Professional Documents
Culture Documents
USB en El Frontal
USB en El Frontal
I guess it's no secret by now that the Chieftec/Antec/Chenming mid tower case is my current favourite
case. I think it's the same with Diceman too with the amount of mod projects/reviews that you see around
here revolving around the case. It's not only it looks, but the features that attracts me and Dice to the case.
Lot's of room, a well-thought out and balanced cooling system is just among the many features of the case
that we love. But one thing that is missing from the case is front USB ports. Antec answered that
shortcoming with their new line of Performance Plus cases, that was reviewed here by Diceman, but it's
just not at the right place. Rather awkward positioning and it kinda interferes with the overall front bezel
look. But that's just me I guess. :O) But what if you're like me? Prefering the old Antec/Chieftec look but
still want those front USB ports? Mod one into the case! That what! So here is the guide for you "oldskool" Antec/Chieftec lovers. Like all custom mod projects, this one requires some degree of planning
and also patience. Heheh! So if you screw things up, don't look at me!
Now before you actually do this mod, you gotta make sure that you have those USB Extension Brackets
that comes with your mobo. Most new motherboards nowadays comes with at least one. Even is they
don't include them, there should still be a USB Header on your motherboard somewhere and you can then
pruchase the brackets separately. Not sure about you folks in the States, but here in Singapore, it's widely
available. I'm using the bracket from my Gigabyte GA-8IRXP P4 mobo. The package comes with two
brackets actually; a bracket with 2 X USB 1.1 ports and another with 4 X USB 2.0 ports. The one I
choose for this project is a no brainer guys! :^) OK, in case you haven't seen one of them brackets before,
here's how it looks like.
As you can see, these brackets were designed to be installed in one of those expansion slots at the back of
your case. No way! This is going in the front!! So, the first thing you need to do here is remove that metal
bracket. Usualy, it's connected to the USB ports by screws so that should make light work of it.
Bracket removed.....
Once you got the bracket removed, it's time to aligned the USB ports to the where you want to mount it in
the case. I chose to mount it on the left side of the Chieftec front bezel (looking from front). There's a
considerable amount of FLAT surface area to mount the ports easily and blends it nicely into the overall
case look. (I have my case on my right side, so the ports are easily accessible). Next thing to do is to mark
out the holes for the ports on the bezel itself. I hope you didn't throw that bracket away! Not only does it
makes marking out easier, but it'll also help you in getting the right size hole and cut-outs, as I will show
you later.
en
av
r
K
y
OK, now that you have a rough idea where to mount your USB ports, let's get to the cutting part!! :O)
Marked out.....
Drilling the holes for the screws is simple enough. For the rectangular USB ports, it's a little more
involved. First drill a couple of holes at each end of the rectangular markings. I then use a cutter/shear to
cut thru the holes and exposed a rather large part of the rectangular ports. This is where the bracket comes
into play again.
Secure the bracket into location with a couple of bolts and nuts on the screw holes that you have drilled
earlier. And using the rectangular holes in the bracket, file away the plastic according to the size of the
bracket. You're sure not to missed or "over-cut" the holes in this manner. This shouldn't take you long.
Once you're done, remove the bracket and you'll have yourself some nice USB ports cut-outs! Heheh!
en
av
r
K
y
Finished Mod
Here you go! Now, that didn't take long, does it? I finished off the cut-outs by sanding it down lightly
with a 600 grit sandpaper. It's up to you really to do this. Now it's time to test the USB ports to the cutouts you just made. Before that, you'll find that there's a ridge running next to the cooling vents and
depending on the type of USB extension port that you got, you'll probably need/need not to cut away part
of the ridge so that the extension port sits in nicely. In my case, I had to trim away a small part of the
ridge to accommodate the extension ports. Nothing I can't handle though! ;oP
DONE!!!
Perfect Fit!
Mod done..
Close-up!
en
av
r
K
y
Preliminary cut...
Done!
Cabling
If you think that's the end, man you're wrong! Them extension ports provided with your mobo are usually
very short in length. Reason being you're to mount them at the back of your case, not at the front. So what
do you do about the cabling? Well, here's how I extended mine so that the connectors are able to reach the
header on my motherboard. Here's what you need for this mod.
First, strip off the main protective layer from the cable and expose about 2 inches of cables inside. Each
of the 10 cables will be covered with different coloured protective layer so it's much easier for you to
ensure the right connection from your USB extension ports to the headers. Using the same connectors as
the one on the USB extension cable, crimp the 10 wires onto the connector terminals. Use the long nose
pliers to secure the wires into the terminals and secure them into the connectors. Do the same for the rest
of the wires and take note of the alignments of the wires at the other end, connecting to your original USB
extension.
en
av
r
K
y
Done!
Now take the double-sided jumper pins and cut them according to the number of pins on the USB
connector. This will be used as a "connecting bridge' between the original USB extension and the
extension cable you just made.
If you're have difficulty trying to look for the 10-wire USB cable for this mod, you can also use the wires
from an old IDE cable that you mght have lying around. Just strip off the required number of wires, like
when you're making your own "round cables" and use the same connector and connector terminals. Much
cheaper and easier to find! :O)
en
av
r
K
y
Looks stock!
Those of you with older motherboards without the USB extension, you can still do this mod if the USB
header is present somewhere on your mobo. If it's not, then tough luck! A 3.5" hub would be better for
ya! :O) I hope this will help you in your own USB port mods for your Chieftec/Antec/Chenming case
folks. Give me a holler if you need help with this! I'll try to help ya out! And if any of you know where to
get the parts for the cabling extension in the States, lemme know so I can post it here for the overseas
folks! Thanks for reading and enjoy!!!
en
av
r
K
y