pla od OE ey
a
ue ok? Ca.
QW-482 SUGGESTED FORMAT FOR WELDING PROCEDURE SPECIFICATIONS (WPS)
(See QW-200.1, Section IX, ASME Boiler and Pressure Vessel Code)
‘Company Name: x By: BUBBA SLAGLINE
Welding Procedure Specification No. SMAW-1 Date: §/5/99 Supporting POR Nos) SMAW-A1_
Revision No. Date:
Welding Process(es): SMAW. Typos [Santee as
‘Auiomalc, Manual, Machine. or Semi-Aule
JOINTS (QW-402) Details
Joint Design GROOVE , ,
Backing (Yes) _______(No)_X. 4 for hae de pat case
Backing Material (Type)
(efor to both backing and retainers) vgs
Metal C1 Nonfusing Metal
1 Nonmetalic - ( Other
‘Sketches, Production Drawings, Weld Symbols or Writon Des- LA
Cripton should show the ganeral rangement ofthe pats to be
welded. Where appleabl, the rot spacing and the deta of )
wold groove may be specifi 13)
(At tho option of the Migr., sketches may be attached to ilus-
trate joint design, wold layers and bead sequence, e.g., for
notch toughness procedures, for multiple process procedures, bala
etc.)
“BASE METALS (QW-403)
P-No._1 Group No._1
‘OR
Specification type and grade
to Specification type and grade
OR
Chem. Analysis and Mech. Prop. -
to Chem. Analysis and Mech. Prop. s 3 ae M
Thickness Range: * on
Fillet’ 4 eae
Base Meta: Groove _1/8" — 1"
“FILLER METALS (QW-408) a
‘Spec. No. (SFA) 1 Golo ol
‘AWS No. (Class) = \E-7
No, 3
ANo.
Size of Filer Metals 9/92" 11/8" tie" = 7132"
Weld Metal SeCuNen es ely
Thickness Range: ~~~) : oe el
roove 250_ s ca lik
Fillet
Electrode-Flux (Class) N/A N/A ee
Flux Trade Name N/A N/A dit
Consumable insert __N/A N/A
Other
“Each base motal-fller metal combination should be recorded individually
Read both this WPS and the attached PQR. Make the proper
corrections based on ASME IX. HINT: This is a procedure
for making a carbon steel pipe weld. ITAC Practice WPS/PQR, Fall, 2001 Page 1QW-482 (Back)
WPS No. SMAW-1 ZL Rev. 0
POSITIONS (QW-405) POSTWELD HEAT TREATMENT (QW-407)
Position(s) of Groove ‘Temperature Range fae
Welding Progression: ‘Time Range bak
Position(s) of Fillet
GAS (QW-408)
PREHEAT (QW-406) Rilseix og Percent Composition
Gas(es) _(Mirture) Flow Rate
Interpass Temp. - Max = Shielding NA
Preheat Maintenance Traling
Backing __
(Continuous or special heating where applicable should be recorded)
ELECTRICAL CHARACTERISTICS (QW-409)__=\y
Current AC or OC DG. Polarity
‘Amps (Range) 19 ___ Volts (Range)
‘(Amps and volts range should be recorded for each et
position, and thickness, etc. This information may i
be listed in a tabular form similar to that shown below.
‘Tungsten Electrode Size and Type N/A
(Pure Tungsten, 2% Thorated, ete.)
Mode of Metal Transfer for GMAW N/A
(Spray are, short-ircuting arc, etc.)
Electrode Wire feed speed range NIA
ay Pane
oc eed
pomfuthow
_- Mana gcluves
[TECHNIQUE (QW-410)
ung or Went Sead weapdur —shiieg /rysare
Siaerous Cp ae
alan nace eaing (natn, Geng og] AS
Method of Back Gouging To baa
Osoillation
Contact Tube to Work Distance
Multiple or Single Pass (por side)
im tigi sete eg eee oe
‘Travel Speed (Flange)
Peening
Other
Flor Metal Curent
Other
Travel | (e.g., Remarks, Comments,
eld Type | Amp | Vott | Spood | Hot Wire Addition, Technique
Layers) |Process | Class | Dia.| Polar_| Range | Range | Range ‘Torch Angle, Ec)
1 smaw | €-7018 | 1/8" | vceP |10-1k| 75 | 21PM
TTAC Practice WPS/PQR, Fall, 2001
u.
Peo
e
eos
Lid,
Page 2QW-483 SUGGESTED FORMAT FOR PROCEDURE QUALIFICATION RECORD (PQR)
(See QW-200.2, Section IX, ASME Boller and Pressure Vessel Code)
Record Actual Conditions Used to Weld Test Coupon
Company Name.
Procedure Qualification Record No.
WPS No, SMAW ~ 1
Date §/5/99
Welding Process(es) _SMAW
‘Types (Manual, Automatic, Semi-Auto.)
So rncc nents anne eg
Ee 2) <8" '
fe] thal dh goat
‘ eel bal
Groove Design of Test Coupon
(For combination qualifications the deposited weld meta thickness willbe roquirad for each filer metal or process used.) |
‘BASE METALS (OW= ss POST WELD Hi iT (W407)
{Matai Spec. Temperate ? Pambian
"Type or Grade aS Time
'P. No. 4 ‘PN. Other
{Thickness of Test Coupon
‘Diameter of Test Coupon
‘other ‘GAS(QW-408)
t Percent Composition
t Gases) (iriure) Flow Rate
Stieling _N/A
'FILLER METALS (QW-404) 7 6. @ Trailing
'SFA Speaification bf Backing
JAWS Classification a i
Fite Metal F-No
‘Weld Mos! Analysis AN,
‘Size of Filer Metal
‘other
‘Weld Metal Thickness 1 }
[POSITION (QW-405) 1
"Position of Groove
|Weld Progression (Uphill, Downhill)
PREHEAT (QW-406)
‘Preheat Temp.
TECHNIQUE (QW-410)
Travel Speed
Sting or Weave Boad
Oscilation (Wea
Multipass or Single Pass (per side) — Myaliaa
Single or Multiple Electrodes,
tintorpass Tomp.
‘other
TTAC Practice WPS/PQR, Fall, 2001 Page 3