Professional Documents
Culture Documents
.O.
1. Do not install the system where it will be exposed to direct
sunlight or rain.
2. The system siren is very loud, never put the unit close to
your ear.
3. The unit should be away from heat sources such as
radiators, heating ducts and stoves.
4. If the system sounds at random, it is possible that the
location too close to a heat source, changing the location or
direction of the unit can remedy this.
5. The system can provide valuable protection for your home
and property if utilized properly. However, this unit cannot
guarantee complete protection against to burglary or
robbery. Therefore, we will not be responsible for any losses
or damages which could occur.
o^c
-1-
^Y
6. For shelf topTurn the sensor head 90 degrees upwards, then rotate the
head 180 desired clockwise to the desired angle. Place in on
the shelf-top location you selected (fig.4)
( ft9' 4)
Unit
, --1 ^^, - ^ _
(fg 1)
PRECAUTIONARY NOTE: IF YOU HAVE ANIMALS
Sensor head can be adjusted if you have dogs, ie. you would
set the sensor head slightly higher avoiding your animal. We
suggest that if you have cats to keep them out of the room that
the Auto Dialer is monitoring.
P^ ( fig. 5)
fig. 2a )
FEATURES
7
,-71 (fig.3)
---^
b ^^I
DC Adaptor
^ r TeiePhone
'
1 TO CHANGE PASSWORD
a. Enter factory pre-set pass number, 0-0-0. Press PROG
button once, PASSWORD will flash on the auto-dialer
screen.
b, Press the ARMlDtSARM button to confirm that you want to
enter the PASSWORD option.
c. Enter your new pass number followed by the ARM/DISARM
button to confirm the new number. (you can choose up to 6
numbers in your pass number)
d. Press the PROG button seven times to exit set-up mode.
NOTE: If you forget your pass number, press and hold down
the PROG button, for up to 2 seconds, after a beep press
PAUSE button, remove the battery and AC adapter after 2
-3-
- MEMORY LOCATION
r yg : (fig.7)
a. Enter the pass number followed by PROG button three
times.
b. The "JOC " icon will flash on the auto-dialer screen.
c. Press ARM/DISARM to confirm that this is the option you
need.
d. Using the UP and DOWN buttons select SOUND OFF.
Followed by the ARM/DISARM button to confirm that the
SIREN is now off.
e. Press the PROG button five times to exit the set-up mode.
-4-
(fig.8)
In standby mode, press and hold the PROG button for more
than two seconds, then key in the test telephone number
memory location, the telephone number stored in memory will
automatically be dialed.
1. Connect the PIR slave extended unit (not included, option for
113E)
a. Connect the PIR slave extended unit cable to the terminal
post located in back of the main unit inside the terminal
compartment. See polarity in( fig.9A)
\aG*
Red
ite
(
..^,".
fg-11
(fig.9A)
11
( fig.12 )
Slave Unit 9 4
^--
(fig.10)
F^93 q^m
l[Ull
91
^^.ihen the 9V battery is running low, the battery low LED will
flash once every 3 seconds to indicate the low battery in ARM
mode.
-7-
D '
-8-
fowtacins arrow
fig. 14)
6. To mount the outdoor siren use the siren stand as a tempiate,
mark locations of holes and install anchors and screws as
shown in fig. It is recommended that you mount the out door
siren at entrance door, top of garage door, or any location
which is sheltered from easy tamper and rain.
(fig.15)
7. Remote control unit battery replacement
(Battery Type-A76 or LR44)
a. Remove the battery compartment cover by sliding it in the
direction of the arrow.
b. Replace with three new batteries of the same type.
Make sure the polarity (+ or -) of the batteries match the
polarity marks inside the unit. As shown in (Fig. 16)
AUTO-DIALER WITH
SECURITYISAFETY
ALARM
MODEL: T016
Li
CDw
WARNING
To ar,y risk or damage, when battery is low make sure
(fig. 16) change the battery immediately, or take the battery out when the
device will be out of use for a long period, to avoid any battery
leakage to damage this device.
=1
1:1
3
(L,) C1
^n^
/s
^/ ^ / ^ 6 ^^
^_L;
(fig.17)
611-01600-OO6R
10-
^
141,1
11-
^..
"
Ijovie Siuje
HomeSafe's unique passive infrared system concentrates on the protected area you select.
Whenever the unit set at ARMED, the motion detector wi44 studied the protected area. Once
there is a movement be detected, the alarm will turn on alarm and call to the memorized
telephone numbers one by one. In chime mode, the chime will Ding Dong when movement be
detected.
EASY TO INSTALL
1. Install battery ( not included), connect AC
ADAPTOR and telephone line (included).
2. Mount on the wal{ to have a height
-;;
-_^
I- 6-8M
4 CE
RECYCLABLE
PAPER
Made in China
639-0160C-001R
Patent Pending
Trademark & Copyright Reserved
6 3I I 9IqI VI I l I 4
22 1 01600