Professional Documents
Culture Documents
Experiment #3: AIRFOIL LIFT AND DRAG MAE 650:433 Aerospace Engineering Laboratory
Experiment #3: AIRFOIL LIFT AND DRAG MAE 650:433 Aerospace Engineering Laboratory
A force balance (fig. 2) is used by researchers to measure the reaction forces and
moments on a model and allows the orientation (angle of attack, pitch, yaw) to be changed
during a test. Complex force balances in large-scale facilities can measure all thee forces and all
three moments on the model simultaneously. The force balance in this experiment will be used to
measure only the axial and normal force relative to the rotation sting as shown in fig. 2. Using
the axial and normal force, and the rotation sting angle , the lift and drag can be computed using
the relationship shown in fig. 2. The forces are measured using the load cell, which is the hollow
rectangular device at the end of the sting. The rotation sting is connected to a shaft equipped
with an indexed rotation stage allowing the angle of attack to be varied throughout the test. Since
the rotation stage is stiff only use the side arm located on the stage on the outside of the tunnel to
rotate the model, DO NOT ROTATE THE STAGE USING THE STING OR THE
AIRFOIL SINCE THEY WILL BREAK. When the thumbscrew on the rotation stage is
loosened, the stage can be rotated coarsely and then when tightened a rotation angle micrometer
fine can be used for a fine adjustment. DO NOT OVER TIGHTEN THE THUMB SCREW
SINCE YOU MAY DAMAGE THE ROTATION STAGE. The load cell uses strain gage
circuits whose voltage output is calibrated to read the force in grams. A two-channel
oscilloscope monitors the load cell bridge outputs and performs averaging of the signals, which
fluctuate because of turbulence.
Four finite wings with three different airfoil types, shown in fig. 3, will be used for this
experiment. PLEASE BE VERY CAREFUL WHEN HANDLING THESE WINGS SINCE
THEY ARE EXTREMELY FRAGILE AND SMALL DENTS AND SCRATCHES CAN
EFFECT THE RESULTS (POINTS WILL BE DEDUCTED FROM THE LAB GROUP
FOR DAMAGE TO AIRFOILS). Airfoils AR l and AR2 are symmetric NACA 0012 airfoils
with two different aspect ratios of 3.96 and 2.05 respectively. Airfoils AR3 and AR4 are NACA
4412 chambered airfoils with and without flaps with the same aspect ratio as AF2. The airfoils
are attached to the load cell using a mounting sting, which is bent so that the airfoils are oriented
at a slight angle of attack when the rotation sting is at zero degrees. This offset mounting sting
angle is needed to provide the needed large airfoil angles of attack during experimentation, since
the force balance has a limited range of 12. The offset angles, , are shown for each airfoil in
fig. 3 so that the actual angle of attack can be calculated for each rotation sting angle, .
EXPERIMENTAL PROCEDURE
Turn the power on to the force balance, which is located on the side of the existing digital bridge
readout, immediately when you arrive and let the unit warm up for approximately 10 minutes
before making measurements. Note that the digital bridge readout cannot provide averaging of
the fluctuating bridge signals and will not be used for this experiment.
Oscilloscope Setup
Channel 1 should be wired to the output of the axial force sensor and Channel 2 should
be wired to the output of the normal force sensor located on the back of the load cell display. The
display should appear as in Figure 4. Note the waveforms and use the average voltage
measurements [Vavg(I) and Vavg(2)] shown at the bottom of the screen. The load cell has been
calibrated so that the voltage output is 1 mV/gram. Following are the settings, which should be
used for this experiment, as well as a description of how to change them:
Next the load balance must be zeroed. To do this turn the Time/Div knob on the
oscilloscope under the HORIZONTAL controls group until the time scale on the scope is 1ms
per division (this will update the average voltage measurement more quickly on the scope). Now
using the zeroing knob on the Normal and Axial force balance controller, turn the knob until the
average voltage displayed on the scope is within 10.0 mV of zero. After zeroing the balance it
will not be necessary to adjust the zero again since a measurement is taken with the flow for each
angle of attack position. Reset the horizontal scale on the oscilloscope to 500.0 ms per division.
Setting the Force Balance Mounting Sting Offset
In general when using a force balance in wind tunnels the researcher would like to
measure only the forces and moments due to the model and neglect the effects of the mounting
hardware and sting which attach the model to the balance. Unfortunately this can be difficult
since the effect of the mounting sting is influenced by the presence of the model. Therefore, it is
customary to use a calibration mounting sting similar to that used on the airfoils, run the tunnel
with only the mounting sting attached, and record the forces for different angles of attack. Since
the load cell is located at the end of the sting the only effect in the present system is due to the
shape of the load cell itself and the small mounting sting.
1. Attach the small calibration mounting sting (the angled cylinder with no airfoil attached) onto
the force balance and slightly tighten the setscrew. Make sure the calibration sting is oriented at
a positive angle of attack when the rotation sting angle () is at zero degrees.
2. With the wind tunnel off zero the wind tunnel speed manometer using the adjustment screw.
3. Turn the wind tunnel on but close the flow control plate so there is no flow in the wind tunnel.
4. Starting with a rotation sting angle of = -18 record the average voltage from the
oscilloscope for the axial and normal forces in 2 increments up to a sting angle of = + 18.
Since the load cell bridge circuitry can drift in time, each measurements should include voltage
readings. To accomplish this, keeping the wind tunnel on for each sting position, first record
the voltages with the control plate fully closed (so that there is no flow in the wind tunnel) and a
then with the control plate fully open (so that tunnel is at maximum velocity). For each
position, record the sting angle, wind tunnel air velocity, and axial and normal force with the
control plate closed and opened. Note that the load cell is calibrated to grams, which needs
conversion Newtons (Oscilloscope output 1 mV/gram, 1 gram * 9.81 m/s2 / 1000 = 1N).
Airfoil Axial and Normal Force Measurements
Four airfoils will be tested using the following procedure for each one.
1. Attach the airfoil to the force balance without tightening the mounting setscrew. Make sure
the airfoil is oriented at a positive angle of attack when the rotation sting angle () is at zero
degrees. To ensure that the airfoil is parallel to the wind tunnel floor increase the sting angle
until the leading edge of the airfoil is almost touching the ceiling of the wind tunnel. With the
mounting sting lose in the load cell, rotate the airfoil until the leading edge of both wing tips are
parallel to the ceiling of the wind tunnel. Slightly tighten the setscrew to secure the airfoil to the
sting.
e. Lift slope
f. Stall
g. Flow separation
h. Kutta condition
2. From the components of the force measurements show that the lift and drag are given by:
D = A cos() + N sin()
and
L = N cos() sin()
where:
L = lift force
D = drag force
A = sting axial force
N = sting normal force
= sting angle
3. Tabulate the sting angle, angle of attack, lift force (L) in Newtons, the drag force (D) in
Newtons, the lift coefficient (CL), and the drag coefficient (CD). Also calculate the Reynolds
(Re) number for each airfoil. These are given by:
CL = L/qS
CD = D/ qS
Re = Vc/
q= V2/2
V is the free stream velocity, S is the plan form area (cord time width) c is the cord length
and is the kinematic viscosity.
5
Note that the mounting sting of the airfoils is at an offset angle not aligned along the imaginary
line from the airfoil leading to trailing edges. Using the sting offset angles in fig. 3 the actual
angle of attack of the airfoils should be calculated from the rotation sting angle () and the sting
offset angle . Also when calculating the lift and drag, the tunnel off and calibration mounting
sting data should be subtracted from the measurements.
4. Plot three graphs: lift coefficient versus angle of attack, drag coefficient versus angle of
attack, and the drag polar (CL versus CD on the x-axis). In each graph show the results for all the
airfoils. Also plot the theoretical lift thin airfoil theory lift coefficient for a symmetric airfoil
which is given from thin airfoil theory as CL = 2.
5. Discuss the differences you observe in the profiles between the airfoils and give the reasons
for the differences when possible. Why do the lift and drag plots have the trends they do (i.e.
what is occurring in the flow field around the airfoil causing the plot to have the shape it does?
Refer to Figure 5 of this handout).
6. Discuss the similarities and differences in the curves obtained from the experiment and the
attached plots from reference 2. Give possible reasons for the differences (note that the
differences are not entirely due to experimental errors). What is the difference between section
drag and the drag measured in this experiment?
7. If you were asked to select an airfoil for a model aircraft with a chord length of 0.2 m and a
velocity of 5 m/s would it be better to use the published data given or measured data from
this experiment (give an explanation for you answer).
From your data, state which airfoil you would use and discuss the reasons why you selected the
airfoil for the following applications.
a. aircraft at cruise conditions
b. aircraft landing
c. racing car spoiler where the rules state that the airfoil must be at zero angle of attack
Be sure to give sample calculations for the above analysis and discuss the accuracy of the results.
REFERENCES
1. Ira H. Abbott and Albert E. Von Doenhoff, "Theory of Wing Sections", Dover Publishing,
New York, 1951.
10
11