Professional Documents
Culture Documents
UE Behaviors in Idle-Mode Description (2008!03!20)
UE Behaviors in Idle-Mode Description (2008!03!20)
Issue
Draft
Date
2008-03-20
Huawei Technologies Co., Ltd. provides customers with comprehensive technical support and service. For any
assistance, please contact our local office or company headquarters.
Website:
http://www.huawei.com
Email:
support@huawei.com
Notice
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but the statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.
RAN
UE Behaviors in Idle Mode Description
Contents
Contents
About This Document.....................................................................................................................1
1 UE Behaviors in Idle Mode Change History........................................................................1-1
2 UE Behaviors in Idle Mode Overview...................................................................................2-1
2.1 Introduction to UE Behaviors in Idle Mode....................................................................................................2-2
2.2 Supported Software Release for UE Behaviors in Idle Mode.........................................................................2-3
RAN
UE Behaviors in Idle Mode Description
Figures
Figures
Figure 3-1 Cell selection procedure for the UE in idle mode...............................................................................3-4
Figure 3-2 Measurement start criteria for cell reselection with HCS disabled....................................................3-7
Figure 3-3 Cell reselection procedure................................................................................................................3-12
iii
RAN
UE Behaviors in Idle Mode Description
Tables
Tables
Table 1-1 Document and product versions...........................................................................................................1-1
Table 2-1 NEs involved in the feature UE behaviors in idle mode......................................................................2-3
Table 2-2 RAN products and related versions......................................................................................................2-3
Table 3-1 UE states involved in the cell selection................................................................................................3-5
Table 3-2 Intra-frequency and inter-frequency measurement criteria for the UE in slow movement.................3-8
Table 3-3 Intra-frequency and inter-frequency measurement criteria for the UE in fast movement...................3-9
Table 3-4 Inter-RAT measurement criteria for the UE in slow movement..........................................................3-9
Table 3-5 Inter-RAT measurement criteria for the UE in fast movement............................................................3-9
Table 3-6 Mapping between the parameters in formulas and the parameters in the LMT.................................3-11
Table 3-7 Parameter list of UE behaviors in idle mode.....................................................................................3-17
RAN
UE Behaviors in Idle Mode Description
RAN
UE Behaviors in Idle Mode Description
RAN Version
RNC Version
NodeB Version
Draft
(2008-03-20)
10.0
V200R010C01B050
V100R010C01B045
Feature change: refers to the change in the feature UE behaviors in idle mode of a specific
product version.
Editorial change: refers to the change in the information that was inappropriately described
or the addition of the information that was not described in the earlier version.
Draft (2008-03-20)
This is the draft of the document for first commercial release of RAN10.0.
Compared with issue 03 (2008-01-20) of RAN6.1, this issue makes the following changes:
Change
Type
Change Description
Parameter Change
Feature
change
None.
None.
Editorial
change
None.
1-1
Change
Type
RAN
UE Behaviors in Idle Mode Description
Change Description
Parameter Change
1-2
RAN
UE Behaviors in Idle Mode Description
2-1
RAN
UE Behaviors in Idle Mode Description
Introduction
Definition
The UE enters the idle mode immediately after the switch-on. The feature "UE behaviors in idle
mode" ensures that the UE is ready to start a service (for example, to make a call or pick a call).
The behaviors mainly include network selection, location registration, paging reception, and
system information reception.
1.
PLMN selection
This procedure ensures that the PLMN selected by the UE provides services properly.
2.
3.
Location registration
This procedure is used by the UE to report its status to the network. This procedure is mainly
of two types: periodical location registration and the location registration caused by location
area change.
Paging reception
The UE detects the paging indicate on the PICH within the predefined time and receives
the corresponding paging information on the S_CCPCH.
Purposes
This feature enables the UE to behave as follows:
l
Impact
Impact on System Performance
This feature has impacts on the following aspects:
l
2-2
The network parameter affects the success rate of service access and paging.
Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
RAN
UE Behaviors in Idle Mode Description
The network parameter affects the power consumption of the UE in idle mode.
The load of the network affects the UE's access to a cell. When the load is heavy, the UE
may fail to access the cell.
NodeB
RNC
MSC
Server
MGW
SGSN
GGSN
HLR
NOTE
: not involved
: involved
NodeB
Version
BSC6800
BSC6810
DBS3800
BTS3812A
BTS3812E
iDBS3800
BTS3812AE
2-3
RAN
UE Behaviors in Idle Mode Description
3-1
RAN
UE Behaviors in Idle Mode Description
Automatic selection
The UE automatically selects a PLMN according to the priority order.
Manual selection
The UE shows all available PLMNs to the subscriber. The subscriber then selects a PLMN.
RAN
UE Behaviors in Idle Mode Description
NOTE
The MCC and MNC in the PLMN identity of the HPLMN match the MCC and MNC in the IMSI of
the UE.
The PLMNs, except the HPLMNs, which the UE camps on, are defined as VPLMNs.
After the UE is switched on, a period of at least two minutes and at most T minutes shall
elapse before the first attempt is made.
Only the priority levels of equivalent PLMNs of the same country (which serve as the
current serving VPLMN) can be compared with the priority level of a selected PLMN.
For more details of the PLMN selection, refer to 3GPP TS 25.304 and 3GPP TS 23.122.
3-3
RAN
UE Behaviors in Idle Mode Description
NOTE
3-4
RAN
UE Behaviors in Idle Mode Description
State
Description
Camped normally
Connected mode
Suitable cell
A suitable cell is the cell that the UE may camp on to obtain normal services.
Acceptable cell
An acceptable cell is the cell that the UE may camp on to obtain limited services. For
example, the UE may originate emergency calls.
3-5
RAN
UE Behaviors in Idle Mode Description
Parameter
Description
Squal
Srxlev
Qqualmeas
Qrxlevmeas
Qqualmin
Qrxlevmin
Pcompensation
Figure 3-1 shows the cell reselection of the UEs in idle mode.
RAN
UE Behaviors in Idle Mode Description
1.
2.
3.
4.
The UE selects a suitable cell to camp on according to the cell reselection criteria.
Intra-frequency measurement
If Squal > Sintrasearch, the UE need not start the intra-frequency measurement.
If system messages do not contain Sintrasearch, the UE always need start the intrafrequency measurement.
Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
3-7
RAN
UE Behaviors in Idle Mode Description
Sintrasearch is set through Intra-freq cell reselection threshold for idle mode on the RNC
side.
l
Inter-frequency measurement
If Squal > Sintersearch, the UE need not start the inter-frequency measurement.
If system messages do not contain Sintersearch, the UE always need start the interfrequency measurement.
Sintersearch is set through Inter-freq cell reselection threshold for idle mode on the RNC
side.
l
Inter-RAT measurement
If Squal > SsearchRATm, the UE need not start the inter-RAT measurement.
If system messages do not contain SsearchRATm, the UE always need start the inter-RAT
measurement.
SsearchRATm is set through Inter-RAT cell reselection threshold on the RNC side.
HCS Enabled
When the HCS is enabled, the measurement criteria for the UE in movement are listed in Table
3-2, Table 3-3, Table 3-4, and Table 3-5.
l
Result
Squal Sintrasearch
SsearchHCS is set through HCS cell reselection threshold on the RNC side.
3-8
RAN
UE Behaviors in Idle Mode Description
The HCS of intra-frequency neighboring cells of a cell is usually consistent with that of
the cell. If the Squal of the current cell is good enough, that is, Squal > Sintrasearch, the UE
only needs to compare the Squal in these cells with different HCSs.
l
Condition
Result
Result
Squal Slimit,SearchRATm
SHCS,RATm is set through HCS inter-rat reselection threshold on the RNC side.
Slimit,SearchRATm is set through HCS search inter-rat limit threshold on the RNC side.
l
Condition
Result
3-9
RAN
UE Behaviors in Idle Mode Description
Condition
Result
If the system information indicates that the HCS is not used, the quality level threshold criterion
H does not apply.
The cell-ranking criterion R is defined by:
where
3-10
RAN
UE Behaviors in Idle Mode Description
Table 3-6 Mapping between the parameters in formulas and the parameters in the LMT
Parameters in Criteria
Parameter ID
Parameter Name
Qhcss
Qhcs
IdleQhyst1s
IdleQhyst2s
TempOffset1
TempOffset2
TpenaltyHcsReselect
Qhcsn
Qhysts
TEMP_OFFSETn
PENALTY_TIMEn
Figure 3-3 shows the cell reselection procedure, which describes the measurement start and
criteria relations. The actual procedure varies with UE implementation.
3-11
RAN
UE Behaviors in Idle Mode Description
Firstly, the UE shall select certain cells that fulfill the S criterion to rank in the following cases:
3-12
When HCS is not used (UseOfHcs is set to NOT_USED), the UE shall rank all cells, not
considering HCS priority levels.
When HCS is used (UseOfHcs is set to USED) and UE is in low mobility, the UE shall
rank all cells that have the highest HCSPrio among those cells that fulfill the criterion H
0.
When HCS is used and UE is in high mobility and if there are cells with a lower HCS
priority than the serving cell that fulfil the criterion H >= 0, the UE shall rank all cells that
have the highest HCSPrio among those cells that fulfil the criterion H >=0 and have a
lower HCS priority than the serving cell.
When HCS is used and UE is in high mobility and if there are cells that fulfil the criterion
H >= 0 with an HCS priority higher or equal to the HCS priority of the serving cell, the UE
Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
RAN
UE Behaviors in Idle Mode Description
shall rank all cells that have the lowest HCSPrio that fulfil the criterion H >= 0 and have
an HCS priority higher or equal to the HCS priority of the serving cell.
l
When HCS is used and if no cell fulfills the criterion H 0, the UE shall rank all cells,
not considering HCS priority levels.
Secondly, the UE shall rank the cells according to the R criteria, deriving Qmeas,n and Qmeas,s
and calculating the R values, as described in the cases below.
The offset IdleQoffset1sn is used for Qoffsets,n to calculate Rn. The hysteresis IdleQhyst1s is
used for Qhysts to calculate Rs.
l
If a TDD or GSM cell is ranked as the best cell, the UE shall reselect that TDD or GSM
cell.
If an FDD cell is ranked as the best cell and the quality measure for cell selection and
reselection is set to CPICH RSCP(QualMeas = CPICH_RSCP), the UE shall reselect that
FDD cell.
If an FDD cell is ranked as the best cell and the quality measure for cell selection and
reselection is set to CPICH Ec/N0(QualMeas = CPICH_ECNO), the UE shall perform a
second ranking of the FDD cells according to the R criteria specified above.
In this case, however, the UE uses the measurement quantity CPICH Ec/N0 for deriving
the Qmeas,n and Qmeas,s, and then calculating the R values of the FDD cells. The offset
IdleQoffset2sn is used for Qoffsets,n to calculate Rn, and the hysteresis IdleQhyst2s is
used for Qhysts to calculate Rs.
If the system information indicates that the HCS is enabled, TempOffset2 is used to
calculate TOn. Otherwise, TEMP_OFFSETn is not used to calculate Rn. Following the
second ranking, the UE shall reselect the best ranked FDD cell.
In all the previous cases, the UE can reselect a new cell only when the following conditions are
met:
l
The new cell is better ranked than the serving cell during a time interval Treselections .
More than one second has elapsed since the UE camped on the current serving cell.
NOTE
3-13
RAN
UE Behaviors in Idle Mode Description
IMSI attach/detach
NOTE
After the switch-on, the UE selects a suitable cell that belongs to a new LA or RA. That is,
the LA or RA is different from that recorded in the USIM before the switch-off of the UE.
When the UE is switched on or the system information indicates that periodic location
registration shall be applied, and the timer T3212 is not running. Then, the timer shall be
loaded with a random value between 0 and the value of T3212, and shall be started.
When the timer T3212 reaches its expiry value, the UE shall initiate the periodic location
registration.
The timer T3212 shall be prevented from triggering periodic location update in connected
mode. When the UE returns to the idle mode, T3212 shall be initiated with respect to the
broadcast timeout value and then be started.
If the UE performs a successful combined routing area update, the timer T3212 shall be
prevented from triggering the periodic location update until the UE starts location update,
for example, because a network operation mode changes or the UE uses non-GPRS services
only.
IMSI Attach/Detach
The IMSI attach/detach process facilitates the fast location registration of the UE in specific
conditions.
When the IMSI attach/detach operation applies, the UE shall send the IMSI detach message to
the network when the UE is switched off or the SIM is removed while being in the UPDATED
state. This IMSI detach message will not be acknowledged by the network.
The system information will contain an indicator indicating whether the IMSI attach/detach
operation is mandatory in the cell. The UE shall operate in accordance with the received value
of the indicator. This indicator, however, shall not be considered in GRPS attach/detach.
3-14
RAN
UE Behaviors in Idle Mode Description
If the UE still stays in the same LA or RA after being switched on again, the UE shall perform
an LR request indicating IMSI attach. Otherwise, the UE shall perform an LR request indicating
normal location update.
You can set IMSI attach/detach indicator by set Attach/detach indication.
Reception Process
When a UE stays in idle mode, the paging to the UE is performed within an LA or RA or the
whole RNC. The UE reads the paging information from the PICH and S-CCPCH. The PICH
indicates when the UE reads the paging information from the S-CCPCH, whereas the S-CCPCH
carries specific paging messages.
Reception Technology
To reduce power consumption, the UE can read the information from the PICH only at a
particular time. This is known as the Discontinuous Reception (DRX) technology. The interval
between two consecutive periods of time is called DRX cycle.
For Frequency Division Duplex (FDD), the DRX cycle length shall be 2k frames, where k is an
integer and is decided by the following three parameters:
l
Any of the stored DRX cycle length for the CN domains where the UE is attached, with no
signaling connection established
3-15
RAN
UE Behaviors in Idle Mode Description
NOTE
If you set a big DRX cycle length coefficient, the period for UE detect paging info will be long; therefore, the
UE can reduce the power consumption. However, the delay for responding to a paging will be long.
MIB
Master Information Block (MIB) provides reference and scheduling information for a
number of SIBs in a cell or one or two Scheduling Blocks (SBs) in a cell. The MIB contains
only the PLMN types supported and the corresponding PLMN identities.
SB
Scheduling Block (SB) provides reference and scheduling information for other SIBs. The
scheduling information of an SIB may be included in the MIB or SB.
SIB
System Information Block (SIB) contains actual system information. It consists of system
information elements (IEs) with the same purpose.
When selecting a new cell, the UE reads the MIB. The UE may locate the MIB through the
predefined scheduling information.
The UE may use the scheduling information in the MIB and SB to locate each SIB to be acquired.
If the UE receives an SIB in a position according to the scheduling information and considers
the content as valid, the UE will read and store the SIB.
3-16
RAN
UE Behaviors in Idle Mode Description
The UE shall consider all current SIBs with an area scope (cell) as invalid, and shall store
and use a new SIB.
Parameter ID
Effective
Level
Configura
tion on ...
T3212
Global
RNC
Attach/detach indication
ATT
Global
RNC
DRXCYCLELENCOEF
Global
RNC
Qqualmin
Cell
RNC
Min RX level
Qrxlevmin
Cell
RNC
Max allowed UE UL TX
power
MaxAllowedUlTxPower
Cell
RNC
IdleSintrasearch
Cell
RNC
IdleSintersearch
Cell
RNC
SsearchRat
Cell
RNC
SsearchHCS
Cell
RNC
Use of HCS
UseOfHcs
Cell
RNC
SHCSRat
Cell
RNC
SlimitSearchRat
Cell
RNC
IdleQoffset1sn
IdleQoffset1sn
Cell
RNC
IdleQoffset2sn
IdleQoffset2sn
Cell
RNC
3-17
RAN
UE Behaviors in Idle Mode Description
Parameter Name
Parameter ID
Effective
Level
Configura
tion on ...
IdleQhyst1s
Cell
RNC
IdleQhyst2s
Cell
RNC
Treselections
Cell
RNC
HCSPrio
Cell
RNC
Qhcs
Cell
RNC
TCRmax
Cell
RNC
CRMaxNum
Cell
RNC
TCrmaxHyst
Cell
RNC
TpenaltyHcsReselect
Cell
RNC
TempOffset1
Cell
RNC
TempOffset2
Cell
RNC
Tcrmaxnonhcs
Cell
RNC
Non-HCS NCR
Ncrnonhcs
Cell
RNC
Tcrmaxhystnonhcs
Cell
RNC
SpeedDependentScalingFactor
Cell
RNC
Inter-freqency scaling
factor for reselection
InterFreqTreselScalingFactor
Cell
RNC
InterRatTreselScalingFactor
Cell
RNC
The following tables describe the detailed information about the parameters related to UE
behaviors in idle mode.
Parameter Tables
Parameter Name
3-18
RAN
UE Behaviors in Idle Mode Description
Parameter ID
IdleSintrasearch
GUI Range
16 to 10, 127
32 to 20
Step: 2
Unit: dB
Default Value
None
Optional/Mandatory
Optional
Effective Level
Cell
Configuration Entity
RNC
MML Command
Description
Parameter Name
Parameter ID
SsearchRat
GUI Range
16 to 10, 127
32 to 20
Step: 2
Unit: dB
Default Value
Optional/Mandatory
Optional
Effective Level
Cell
Configuration Entity
RNC
MML Command
Description
3-19
RAN
UE Behaviors in Idle Mode Description
Parameter Name
Parameter ID
SHCSRat
GUI Range
53 to 45
105 to 91
Step: 2 (53:105; 52:103; ..., 45:91)
Unit: dB
Default Value
Optional/Mandatory
Optional
Effective Level
Cell
Configuration Entity
RNC
MML Command
Description
Parameter Name
Parameter ID
SlimitSearchRat
0GUI Range
16 to 10
32 to 20
Step: 2
Unit: dB
3-20
Default Value
Optional/Mandatory
Optional
Effective Level
Cell
Configuration Entity
RNC
MML Command
Description
Parameter Name
SIB11 Indicator
Parameter ID
SIB11Ind
RAN
UE Behaviors in Idle Mode Description
GUI Range
FALSE, TRUE
None.
Default Value
TRUE
Optional/Mandatory
Optional
Effective Level
Cell
Configuration Entity
RNC
MML Command
ADD INTRAFREQNCELL
MOD INTRAFREQNCELL
ADD INTERFREQNCELL
MOD INTERFREQNCELL
Description
Parameter Name
IdleQoffset1sn
Parameter ID
IdleQoffset1sn
GUI Range
50 to 50
50 to 50
Unit: dB
Default Value
Optional/Mandatory
Optional
Effective Level
Cell
Configuration Entity
RNC
MML Command
ADD INTRAFREQNCELL
MOD INTRAFREQNCELL
ADD INTERFREQNCELL
MOD INTERFREQNCELL
ADD GSMNCELL
MOD GSMNCELL
3-21
RAN
UE Behaviors in Idle Mode Description
Description
Parameter Name
IdleQoffset2sn
Parameter ID
IdleQoffset2sn
GUI Range
50 to 50
50 to 50
Unit: dB
Default Value
Optional/Mandatory
Optional
Effective Level
Cell
Configuration Entity
RNC
MML Command
ADD INTRAFREQNCELL
MOD INTRAFREQNCELL
ADD INTERFREQNCELL
MOD INTERFREQNCELL
Description
3-22
Parameter Name
Parameter ID
IdleQhyst1s
GUI Range
0 to 20
RAN
UE Behaviors in Idle Mode Description
0 dB to 40 dB
Step: 2
Unit: dB
Default Value
Optional/Mandatory
Optional
Effective Level
Cell
Configuration Entity
RNC
MML Command
ADD CELLSELRESEL
MOD CELLSELRESEL
Description
Parameter Name
Parameter ID
IdleQhyst2s
GUI Range
0 to 20, 255
0dB to 40dB
Step: 2
Unit: dB
Default Value
IdleQhyst1s
Optional/Mandatory
Optional
Effective Level
Cell
Configuration Entity
RNC
MML Command
ADD CELLSELRESEL
MOD CELLSELRESEL
Description
3-23
RAN
UE Behaviors in Idle Mode Description
Parameter Name
Parameter ID
QUALMEAS
GUI Range
None
Default Value
CPICH_ECNO
Optional/Mandatory
Optional
Effective Level
Cell
Configuration Entity
RNC
MML Command
Description
Parameter Name
Parameter ID
Qqualmin
GUI Range
24 to 0
24 to 0
Unit: dB
3-24
Default Value
18
Optional/Mandatory
Optional
Effective Level
Cell
Configuration Entity
RNC
MML Command
Description
Parameter Name
Min RX level
Parameter ID
Qrxlevmin
GUI Range
58 to 13
RAN
UE Behaviors in Idle Mode Description
115 to 25
Step: 2 (58:115; 57:113; ..., 13:25)
Unit: dBm
Default Value
58
Optional/Mandatory
Optional
Effective Level
Cell
Configuration Entity
RNC
MML Command
Description
Parameter Name
Parameter ID
MaxAllowedUlTxPower
GUI Range
50 to 33
Unit: dBm
Default Value
None
Optional/Mandatory
Optional
Effective Level
Cell
Configuration Entity
RNC
MML Command
Description
Parameter Name
Parameter ID
IdleSintersearch
GUI Range
16 to 10, 127
32dB to 20dB
Step: 2dB
Default Value
None
3-25
RAN
UE Behaviors in Idle Mode Description
Optional/Mandatory
Optional
Effective Level
Cell
Configuration Entity
RNC
MML Command
Description
Parameter Name
Parameter ID
Treselections
GUI Range
0 to 31
0 to 31
Step: 1 second
3-26
Default Value
Optional/Mandatory
Optional
Effective Level
Cell
Configuration Entity
RNC
MML Command
Description
Parameter Name
Use of HCS
Parameter ID
UseOfHcs
GUI Range
USED, NOT_USED
None.
Default Value
NOT_USED
Optional/Mandatory
Optional
RAN
UE Behaviors in Idle Mode Description
Effective Level
Cell
Configuration Entity
RNC
MML Command
ADD CELLHCS
MOD CELLHCS
Description
None.
Parameter Name
Parameter ID
HCSPrio
GUI Range
0 to 7
None.
Default Value
Optional/Mandatory
Optional
Effective Level
Cell
Configuration Entity
RNC
MML Command
ADD CELLHCS
MOD CELLHCS
Description
None.
Parameter Name
Parameter ID
Qhcs
GUI Range
0 to 99
Default Value
20
Optional/Mandatory
Optional
Effective Level
Cell
Configuration Entity
RNC
3-27
RAN
UE Behaviors in Idle Mode Description
MML Command
ADD CELLHCS
MOD CELLHCS
Description
None.
Parameter Name
Parameter ID
TCRmax
GUI Range
0, 1, 2, 3, 4, 5
Unit: s
Default Value
D60
Optional/Mandatory
Optional
Effective Level
Cell
Configuration Entity
RNC
MML Command
ADD CELLHCS
MOD CELLHCS
Description
None.
Parameter Name
Parameter ID
CRMaxNum
GUI Range
0 to 16
None.
Default Value
Optional/Mandatory
Optional
Effective Level
Cell
Configuration Entity
RNC
MML Command
ADD CELLHCS
MOD CELLHCS
3-28
Description
None.
Parameter Name
RAN
UE Behaviors in Idle Mode Description
Parameter ID
TCrmaxHyst
GUI Range
0, 1, 2, 3, 4, 5, 6, 7
Unit: s
Default Value
D20
Optional/Mandatory
Optional
Effective Level
Cell
Configuration Entity
RNC
MML Command
ADD CELLHCS
MOD CELLHCS
Description
Parameter Name
Parameter ID
TpenaltyHcsReselect
GUI Range
Default Value
D0
Optional/Mandatory
Optional
Effective Level
Cell
Configuration Entity
RNC
MML Command
ADD INTRAFREQNCELL
MOD INTRAFREQNCELL
ADD INTERFREQNCELL
MOD INTERFREQNCELL
ADD GSMNCELL
MOD GSMNCELL
Description
The larger the value of this parameter is, the longer the
penalty time for HCS cell reselection is.
Parameter Name
3-29
RAN
UE Behaviors in Idle Mode Description
Parameter ID
TempOffset1
GUI Range
Default Value
D3
Optional/Mandatory
Optional
Effective Level
Cell
Configuration Entity
RNC
MML Command
ADD INTRAFREQNCELL
MOD INTRAFREQNCELL
ADD INTERFREQNCELL
MOD INTERFREQNCELL
ADD GSMNCELL
MOD GSMNCELL
Description
Parameter Name
Parameter ID
TempOffset2
GUI Range
Default Value
D2
Optional/Mandatory
Optional
Effective Level
Cell
Configuration Entity
RNC
MML Command
ADD INTRAFREQNCELL
MOD INTRAFREQNCELL
ADD INTERFREQNCELL
MOD INTERFREQNCELL
ADD GSMNCELL
MOD GSMNCELL
3-30
RAN
UE Behaviors in Idle Mode Description
Description
Parameter Name
Parameter ID
Tcrmaxnonhcs
GUI Range
not used,D30,D60,D120,D180,D240
not used,30,60,120,180,240
Unit: s
Default Value
not used
Optional/Mandatory
Optional
Effective Level
Cell
Configuration Entity
RNC
MML Command
ADD CELLSELRESEL
MOD CELLSELRESEL
Description
Parameter Name
Non-HCS NCR
Parameter ID
Ncrnonhcs
GUI Range
1 to 16
1 to 16
Unit: times
Default Value
Optional/Mandatory
Optional
Effective Level
Cell
Configuration Entity
RNC
MML Command
ADD CELLSELRESEL
MOD CELLSELRESEL
Description
3-31
RAN
UE Behaviors in Idle Mode Description
Parameter Name
Parameter ID
Tcrmaxhystnonhcs
GUI Range
Default Value
None.
Optional/Mandatory
Optional
Effective Level
Cell
Configuration Entity
RNC
MML Command
ADD CELLSELRESEL
MOD CELLSELRESEL
Description
This parameter specifies the extra time before nonHCS resume slow movement.
Parameter Name
Parameter ID
SpeedDependentScalingFactor
GUI Range
0 to 10, 255
0 to 1
Step: 0.1
Unit: None
Default Value
None.
Optional/Mandatory
Optional
Effective Level
Cell
Configuration Entity
RNC
MML Command
ADD CELLSELRESEL
MOD CELLSELRESEL
Description
3-32
RAN
UE Behaviors in Idle Mode Description
Parameter Name
Parameter ID
InterFreqTreselScalingFactor
GUI Range
4 to 19, 255
1 to 4.75
Step: 0.25
Unit: None
Default Value
None.
Optional/Mandatory
Optional
Effective Level
Cell
Configuration Entity
RNC
MML Command
ADD CELLSELRESEL
MOD CELLSELRESEL
Description
This parameter is used to increase the time of interfrequency reselection. This parameter is not
configured when its value is 255.
Parameter Name
Parameter ID
InterRatTreselScalingFactor
GUI Range
4 to 19, 255
1 to 4.75
Step: 0.25
Unit: None
Default Value
None.
Optional/Mandatory
Optional
Effective Level
Cell
Configuration Entity
RNC
MML Command
ADD CELLSELRESEL
MOD CELLSELRESEL
Description
Parameter Name
3-33
RAN
UE Behaviors in Idle Mode Description
Parameter ID
SsearchHCS
GUI Range
53 to 45
105 to 91
Step: 2
Unit: dB
Default Value
Optional/Mandatory
Optional
Effective Level
Cell
Configuration Entity
RNC
MML Command
ADD CELLHCS
MOD CELLHCS
Description
The GUI value and physical value are mapped as: (-53:
-105; -52: -103; ..., 45: 91)
Parameter Name
Parameter ID
T3212
GUI Range
0 to 255
3-34
Default Value
10
Optional/Mandatory
Optional
Effective Level
Global
Configuration Entity
RNC
MML Command
Description
Parameter Name
Parameter ID
DRXCYCLELENCOEF
RAN
UE Behaviors in Idle Mode Description
GUI Range
6 to 9
26to 29
Unit: 10 ms
Default Value
Optional/Mandatory
Optional
Effective Level
Global
Configuration Entity
RNC
MML Command
Description
Parameter Name
Attach/detach indication
Parameter ID
ATT
GUI Range
NOT_ALLOWED, ALLOWED
None.
Default Value
ALLOWED
Optional/Mandatory
Optional
Effective Level
Global
Configuration Entity
RNC
MML Command
Description
3-35
RAN
UE Behaviors in Idle Mode Description
4-1
RAN
UE Behaviors in Idle Mode Description
3GPP, TS 23.122 "NAS Functions related to Mobile Station (MS) in idle mode"
3GPP, TS 24.008 "Mobile radio interface layer 3 specification; Core Network Protocols Stage 3"
3GPP, TS 25.304 "UE Procedures in Idle Mode and Procedures for Cell Reselection in
Connected Mode"
5-1