Professional Documents
Culture Documents
By Joe Botha
Looking for a single-mode (SM) fibre to light-up your multi-terabit per second system? Probably not, but lets say you
were - the smart money is on your well-intended fibre sales rep instinctively flogging you ITU-T G.652D fibre.
Commonly referred to as standard SM fibre and also known as Non-Dispersion-Shifted Fibre (NDSF) - the oldest and
most widely deployed fibre. Not a great choice, right? You bet. So for now, lets resist the notion that you can do
whatever-you-want using standard SM fibre. A variety of SM optical fibres with carefully optimised characteristics
are available commercially: ITU-T G.652, 653, 654, 655, 656 or 657 compliant.
Designs of SM fibre have evolved over the decades and present-day options would have us deploy G.652D, G.655 or
G.656 compliant fibres. Note that G.657A is essentially a more expressive version of G.652D, with a superior bending
loss performance and should you start feeling a little benevolent towards deploying it on a longish-haul - I can
immediately confirm that this allows for a glimpse into the workings of silliness. Dispersion Shifted Fibre (DSF) in
accordance with G.653 has no chromatic dispersion at 1550 nm. However, they are limited to single-wavelength operation
due to non-linear four-wave mixing. G.654 compliant fibres were developed specifically for undersea un-regenerated
systems and since our focus is directed toward terrestrial applications - lets leave it at that.
In the above context, the plan is to briefly weigh up G.652D, G.655 and G.656 compliant fibres against three parameters
we calculate (before installation) and measure (after installation). I must just point-out that the fibre coefficients used are
what one would expect from the not too shabby brands available today.
Attenuation
Attenuation is the reduction or loss of optical power as light
travels through an optical fibre and is measured in decibels per
nm
dB/km
nm
dB/km
nm
dB/km
kilometer (dB/km). G.652D offers respectable attenuation
1310
0.30
1310
1310
coefficients, when compared with G.655 and G.656. It should be
1550
0.20
1550
0.18
1550
0.20
1625
0.23
1625
0.20
1625
0.22
remembered, however, that even a meagre 0.01 dB/km attenuation
improvement would reduce a 100 km loss budget by a full dB - but let's not quibble. No attenuation coefficients for G.655
and G.656 at 1310? It was not, as you may immediately assume, an oversight. Both G.655 and G.656 are optimized to
support long-haul systems and therefore could not care less about running at 1310 nm. A cut-off wavelength is the
minimum wavelength at which a particular fibre will support SM transmission. At 1260 nm, G.652 D has the lowest
cut-off wavelength - with the cut-off wavelengths for G.655 and G.656 sitting at 1480 nm and 1450 respectively which explains why we have no attenuation coefficient for them at 1310 nm.
G.652D compliant
ATTN
G.655 compliant
ATTN
G.656 compliant
ATTN
PMD
G.652D compliant
PMD
G.655 compliant
PMD
G.656 compliant
PMD
ps / km
ps / km
ps / km
0.06
0.04
0.04
optical fibre causes the polarized modes of the light pulse to travel at marginally different speeds, distorting the signal and
is reported in ps / km, or "ps per root km". Oddly enough, G.652 and co all possess decent-looking PMD coefficients.
Now then, popping a 40-Gbps laser onto my fibre up against an ultra-low 0.04 ps / km, my calculator reveals that the
PMD coefficient admissible fibre length is 3,900 km and even at 0.1 ps / km, a distance of 625 km is achievable.
So far so good? But wait, there's more. PMD is particularly troublesome for both high data-rate-per-channel and high
wavelength channel count systems, largely because of its random nature. Fibre manufacturers PMD specifications are
accurate for the fibre itself, but do not incorporate PMD incurred as a result of installation, which in many cases can be
many orders of magnitude larger. It is hardly surprising that questionable installation practices are likely to cause
imperfect fibre symmetry - the obvious implications are incomprehensible data streams and mental anguish. Moreover,
PMD unlike chromatic dispersion (to be discussed next) is also affected by environmental conditions, making it
unpredictable and extremely difficult to find ways to undo or offset its effect.
CD
652D compliant
CD
G.655 compliant
CD
G.656 compliant
CD
nm
ps/(nmkm)
nm
ps/(nmkm)
nm
ps/(nmkm)
1550
1625
18
22
1550
1625
2~6
8~11
1550
1625
6.0~10
8.0~13
CD is exceeded - light pulses representing a bit-stream will be rendered illegible. It is expressed in ps/ (nmkm). At 2.5Gbps CD is not an issue - however, lower data rates are seldom desirable. But at 10-Gbps, it is a big issue and the issue
gets even bigger at 40-Gbps.
Whats troubling is G.652Ds high CD coefficient - which one glumly has to concede, is very poor next to the
competition. G.655 and G.656, variants of non-zero dispersion-shifted fibre (NZ-DSF), comprehensively address
G.652Ds shortcomings. It should be noted that nowadays some optical fibre manufacturers dont bother with
distinguishing between G.655 and G.656 - referring to their offerings as G.655/6 compliant.
On the face of it, one might suggest that the answer to our CD problem is to send light along an optical fibre at a
wavelength where the CD is zero (i.e. G.653). The result? It turns out that this approach creates more problems than it is
likely to solve - by unacceptably amplifying non-linear four-wave mixing and limiting the fibre to single-wavelength
operation - in other words, no DWDM. That, in fact, is why CD should not be completely lampooned. Research revealed
that the fibre-friendly CD value l i e s in the range of 6-11 ps/nmkm. Therefore, and particularly for high-capacity
transport, the best-suited fibre is one in which dispersion is kept within a tight range, being neither too high nor too low.
NZ-DSFs are available in both positive (+D) and negative (-D) varieties. Using NZ-DSF -D, a reverse behavior of the
velocity per wavelength is created and therefore, the effect of +CD can be cancelled out. I almost forgot to mention, by
the way, that short wavelengths travel faster than long ones with +CD and longer wavelengths travel faster than short ones
with -CD. New sophisticated modulation techniques such as dual-polarized quadrature phase-shift keying (DP-QPSK)
using coherent detection, yields high quality CD compensation. However, because of the added signal processing time
(versus simple on-off keying) they require, this can potentially be a poor choice from a latency perspective.
10-Gbps CWDM
40-Gbps CWDM
10-Gbps DWDM
40-Gbps DWDM
100-Gbps DWDM