Professional Documents
Culture Documents
Multiple Choice Questions
Multiple Choice Questions
2. In a CMOS IC
(a) Only N-channel MOSFET is used
(b) Only P-channel MOSFET is used
(c) Both N-channel and P-channel MOSFETs are used
(d) Either N-channel or P-channel MOSFET is used
2
5. A ROM is a device that contains
(a) OR gate only
(b) Decoder only
(c) Decoder and OR gate
(d) Encoder and decoder
6. Intel i860 is a
(a) 32-bit OMS microprocessor
(b) 32-bit HMOS microprocessor
(c) 64-bit RISC microprocessor
(d) 8-bit microprocessor
3
10. The contents of EPROM can be erased by exposing it to
(a) Ultra violet light
(b) Infra red light
(c) Monochrome light
(d) Microwaves
13. A memory chip organized as the 64x8 has _____ number of storage locations
(a) 65536
(b) 65548
(c) 65525
(d) 65575
4
15. A 40 bit wide address bus can directly access _____ byte of memory
(a) 1 Kilo
(b) 1 Mega
(c) 1 Giga
(d) 1 Tera
17. When a bit of one byte changes, then ________ of that byte must also change
(a) Zero
(b) Nonparty
(c) Parity
(d) Carry
iv) SBUF
v) SP
5
20. The SP is of ___ wide register. And this may be defined anywhere in the ______.
(a)8 byte, on-chip 128 byte RAM.
(b) 8 bit, on chip 128 byte RAM.
(c) 8 bit, on chip 256 byte RAM.
(d) 16 bit, on-chip 128 byte ROM
23. If the __ pin is ___ , then we have the option of using the ____ ROM or EPROM together
with _____ memory and devices.
24.In BCD, each decimal digit is represented by _____ bits of binary code.
(a) 5
(b) 2
(c) 3
(d) 4
6
25. A parity checker can be employed to detect __ bit error
(a) one
(b) Two
(c) Three
(d) Four
33. Interfacing LCD with 8051 _____ data lines are used along with the _____ signals.
(a) 6, RS, RW
(b) 8, RS, EN, RW
(c) 5, RW, EN
(d) 9, RS, EN, RW
(b) 1/ (2 -1)
N
(c) 2 -1
(d) 2N-1
8
35. During interface LCD to a microcontroller _______ line will instruct the LCD that
microcontroller is sending data.
(a) DB0
(b) RW
(c) EN
(d) RS
36. _______ pin of port 3 has an alternative function as write control signal for external data
memory.
(a) P3.8
(b) P3.6
(c) P3.3
(d) P3.1
37. An interrupt in which the extended device supplies the address as well as the interrupt
request is
(a) Vectored interrupt
(b) Non Vectored interrupt
(c) Maskable interrupt
(d) I/O interrupt
9
39.The process in which a computer based on microprogramming principle made to
execute the instruction of another computer is called as
(a) Protection
(b) Transformation
(c) Emulation
(d) Pipelining
41. In 8051 an external interrupt 1 vector address is of ________ and causes of interrupt if
____.
42. _______ are the Address (SFR) for TCON, SCON, SBUF, PCON and PSW respectively.
(a) 98H, 99H, 87H, 88H, 0D0H
(b) 0D0H, 87H, 88H, 99H, 98H
(c) 87H, 88H, 0D0H, 98H, 99H
(d) 88H, 98H, 99H, 87H, 0D0H.
10
44. Serial port vector address is of _______and causes an interrupt when ________.
(a) BR=2
(b) BR=2
SMOD
(c) BR=2
(d) BR=2
46. When operated in mode 2, 8255 supplies _____ number of hand shake signals
(a) 3
(b) 5
(c) 4
(d) 6
11
48. A thermistor has _______ temperature coefficient of resistance
(a)Positive
(b)Zero
(c)Negative
(d)Either positive or negative
50. The phenomenon of conversion of electrical energy to light energy is known as_____
(a) Photo resistive
(b)Electro luminance
(c )Photo conductive
(d)Photo voltaic