Professional Documents
Culture Documents
http://iwing.wordpress.com
http://www.ittelkom.ac.id/pinguin
----------------------------------------------------------
Membuat Tunnel di router cnc2 dan cnc3
----------------------------------------------------------
cnc2#sh run int tun 1
Building configuration...
cnc2#
cnc3#sh run int tun 1
Building configuration...
cnc3#
The command no ipv6 nd ra suppress is required as the router does not send RA
messages on Tunnel interface (disabled by default).
----------------------------------------------------------
how to check 1 (sh ipv6 int brief)
----------------------------------------------------------
----------------------------------------------------------
how to check 2 (sh int tun 1)
----------------------------------------------------------
cnc2#sh int tun 1
Tunnel1 is up, line protocol is up
Hardware is Tunnel
MTU 17920 bytes, BW 100 Kbit/sec, DLY 50000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation TUNNEL, loopback not set
Keepalive not set
Tunnel source 192.168.20.1 (FastEthernet1/0)
Tunnel protocol/transport IPv6 ISATAP
Tunnel TTL 255
Tunnel transport MTU 1480 bytes
Tunnel transmit bandwidth 8000 (kbps)
Tunnel receive bandwidth 8000 (kbps)
Last input never, output 00:03:01, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
0
Queueing strategy: fifo
Output queue: 0/0 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
2 packets input, 268 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
11 packets output, 1116 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 unknown protocol drops
0 output buffer failures, 0 output buffers swapped out
cnc2#
cnc3#sh int tunnel 1
Tunnel1 is up, line protocol is up
Hardware is Tunnel
MTU 17920 bytes, BW 100 Kbit/sec, DLY 50000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation TUNNEL, loopback not set
Keepalive not set
Tunnel source 192.168.20.2 (FastEthernet1/0)
Tunnel protocol/transport IPv6 ISATAP
Tunnel TTL 255
Tunnel transport MTU 1480 bytes
Tunnel transmit bandwidth 8000 (kbps)
Tunnel receive bandwidth 8000 (kbps)
Last input never, output 00:04:11, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
0
Queueing strategy: fifo
Output queue: 0/0 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
4 packets input, 536 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
9 packets output, 876 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 unknown protocol drops
0 output buffer failures, 0 output buffers swapped out
cnc3#
----------------------------------------------------------
how to check 3 (ping and traceroute)
----------------------------------------------------------
cnc1#ping ipv6
Target IPv6 address: 13::13:2
Repeat count [5]: 100
Datagram size [100]:
Timeout in seconds [2]:
Extended commands? [no]:
Type escape sequence to abort.
Sending 100, 100-byte ICMP Echos to 13::13:2, timeout is 2 seconds:
!!!!!!!!!!!!!!!!!!!!!!!!..!.!!!!!!!!!!!!!!!!!!!!!!!!!!!!!.!...!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Success rate is 93 percent (93/100), round-trip min/avg/max =
112/283/1824 ms
cnc1#
cnc1#traceroute 13::13:2
----------------------------------------------------------
----------------------------------------------------------
"Sekian dulu dan semoga bermanfaat"
Ref:
[1]. Cisco IOS IPv6 Configuration Guide, URL:http://www.cisco.com, (April 2010)
[2]. RFC 4214.