Standard for properties of cold rolled steel strip (chemical composition) Standard for properties of cold rolled steel strip (hardness) Standard for properties of cold rolled steel strip (bend test) Thickness tolerances for cold rolled steel strip (under 23 15/16 inches in rolled width) Width tolerances of no. 2 edge (mill edge) for cold rolled steel strip (under 23 15 /16 inches in rolled width) Width tolerances of no. 3 edge (slit edge) for cold rolled steel strip (under 23 15 /16 inches in rolled width) Width tolerances of no. 1, 4, 5 and 6 edges rolled steel strip (under 23 15 /16 inches rolled width) Length tolerances for cold rolled steel strip (under 23 15/16 inches rolled width) ASTM A 109 Camber tolerances for cold steel strip (under 23 15?16 inches in rolled width) ASTM A366 Standard for properties of cold rolled steel sheets (chemical composition) A619 Standard for properties of cold rolled steel sheet (chemical composition) A620 Standard fort properties of cold rolled steel strip (chemical composition)
Thickness tolerances for cold steel sheet (coils and cut sheet over 12 inches in width) Thickness tolerances for cold rolled steel sheet (coils and sheet over 2 to under 12 inches in width) Width tolerances for cold rolled steel sheet (coils and cut sheet over 12 inches in width, not resquared) Width tolerances for cold rolled steel sheet (cut sheet/ coils between 2-12 inches in width, 0.014-0.082 in thickness and over 12 inches in length, not resquared) Length tolerances for cold rolled s2teel sheet (cut sheet/ coils between 2-12 inches in width 0.014- 0.082 in thickness and over 12 inches in length ,not resquared) Camber tolerances for cold rolled steel sheet (cut sheet over 12 inches in width not resquared) Camber tolerances for cold rolled steel sheet (over 2 to under 12 inches in width ,over 0.014yto under 0.08 inches in thickness.) Flatness tolerances for cold rolled steel sheet (cut sheet over 12 inches in width , stretcher leveler finish not specified) Flatness tolerances for cold rolled steel sheet (cut sheet, stretcher leveler specified) ASTM A 568 Out-of -square tolerances for cold rolled steel sheet over 12 inches in width , not resquared)
DIN 1623 Unified under EN 10130 DIN 1624 DIN standard for properties of cold rolled steel sheet (carbon steel sheet and strip with narrow width of under 650 mm) DIN 1541 Unified under EN 10130 DIN 1544 Thickness tolerance for cold rolled steel (under 650 mm in rolled width) Thickness tolerances for cold rolled steel and strip Thickness tolerances for cold rolled steel strip (high yield steel point) Width tolerances for cold rolled steel sheet and strip with wide width. BS EN 10131 Width tolerances for cold rolled strip (less than 650 mm in width) Width tolerances for cold rolled steel strip (under 650 mm in rolled width) Length tolerances for cold rolled steel strip (under 650 mm in rolled width)
Camber tolerances for cold rolled steel strip (under 650 mm in rolled width) Standard properties of cold rolled steel strip (chemical composition and mechanical properties BS EN 10130 Surface finished and surface roughness of cold rolled steel strip .
Length tolerances for cold rolled steel sheet Flatness tolerances for cold rolled steel sheet
Flatness tolerances for cold rolled steel sheet (high yield point steel over 280 to less than 360N/mm 2 ) Chemical composition of cold rolled carbon steel sheet. Mechanical properties of cold rolled steel sheet Thickness tolerances for cold rolled steel sheet and strip Width tolerances for cold rolled steel and strip with width Length tolerances for cold rolled steel sheet Camber tolerances for cold rolled steel sheet and strip ISO 3574 Flatness tolerances for cold rolled steel sheet
JIS J 3125 Cold rolled superior atmospheric corrosion resistant steel JIS J 3133 Decaburised steel sheet and strip for porcelain enamelling JIS G 3135 Cold rolled high strength steel sheet with improved formability for automobiles structural uses JIS G 3141 Specification for cold rolled steel sheet and strip JIS G 3302 Specification for hot-dip-zinc coated steel sheet and coils JIS G 3316 Specification for shapes and dimension of corrugated sheet
Equivalent Standards Grade IS 513 JIS G 3141 BS 1449 DIN 1623 ASTM A366,A366M,A619,A619M,A620,A620M EN 10130 Commercial quality O SPCC CR4 CQ FEP01 Drawing quality D SPCD CR3 ST 12,13 CQ FEP03 Deep drawing quality DD SPCE CR2 ST14 DQ FEP03 Extra deep drawing quality (Al Killed, Non Ageing) EDD SPCEN CR1 EDDQ FEP04 Extra deep drawing quality (IF Grade) FEP05 Super extra deep drawing quality (IF Grade)
FEP06
IS 513 chemical composition (max permissible limit for each element) Mechanical properties Hardness max Grade * (Al Killed) C% Mn% P% S% YS (MPA) MAX TS (MPA) ELONGATION % MIN HRB HR30T O 0.15 0/60 0.055 0.055 - - - - - D 0.12 0.50 0.040 0.040 280 270-410 23 65 60 DD 0.10 0/45 0.035 0.035 250 270-310 26 57 55 EDD 0.08 0.40 0.030 0.030 220 270-350 32 50 50 DIN 1623 Part 1 Cold Rolled Sheet and Strip for Cold Forming St 12* 0.10
280 270-410 28 65 60 St 13* 0.10 240 270-310 34 55 53 St 14* 0.08
210 270-350 38 50 50
CR Standards (Uncoated & Coated) contd. JIS G 3141 Cold Rolled Carbon Steel Sheet & Strip TS(MPA) Elongation %, min for thickness(t) in mm Symbol of class t>=0.25 0.25<=t<0.4 0.4<=t<0.6 0.6<=t<1.0 1.0<=t<1.6 1.6<=t<2.5 2.5 or over SPCC 270 32 34 36 37 38 39 SPCD 270 34 36 38 39 40 41 SPCE 270 36 38 40 41 42 43
Erichsen Value for thickness in mm Symbol of class 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.2 1.4 1.6 Remarks SPCC 7.2 7.8 8.4 8.8 9.1 9.4 9.6 10.0 10-3 10.5 for general use SPCD 7.6 8.2 8.8 9.2 9.5 9.8 10.0 10.4 10.7 10.9 for deep drawing use SPCE 8.0 8.6 9.2 9.6 9.9 10.2 10.4 10.8 11.1 11.3 for extra deep drawing
Temper grad e Surface finished Symbol Hardness Hr B HV 1/8 hard dull/bright finished SPCC-86/ 8B 50 71 95 130 1/4 hard dull/bright finished SPCC-4D/4B 65 80 115 150 1/2 hard dull/bright finished SPCC-2D/2B 74 89 135 185 full hard dull/bright finished SPCC-1D/1B 85min 170min
Temper grade Surface finished symbol As annealed SPCC-A, SPCD-A, SPCE-A Standard temper grade Dull / Bright finished SPCC-SD/SB. SPCD-SD/SB, SPCE-SE/SB Std temp grade (when specified to guarantee mechanical properties) Dull / Bright finished SPCCT-SD/SB, SPCEN-SD/SB
JIS G 3135 Cold Rolled High Strength Steel with Improved Formability for Automobile Structural Use New Spec. Conventional Spec. Mechanical Properties YS (MPA) min TS (mpa) min % Elong. min
BS 1449 Part 1 Carbon Steel Sheet & Strip Chemical Composition (max permissible limit for each element) Mechnical Properties % Elong. min (Original Gauge Length, Lo) Grade C% Mn% P% S% YS (MPA) min TS (MPA) min 50 mm 80 mm 200 mm CR4 0.12 0.60 0.050 0.050 140 280