Professional Documents
Culture Documents
com
Code No: A107320402 Set No. 1 JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY HYDERABAD III B.Tech. II Sem., I Mid-Term Examinations, February 2011 MICROWAVE ENGINEERING Objective Exam Name: ______________________________ Hall Ticket No. A I 1. Choose the correct alternative: Which of the following modes are impossible in a circular waveguide? A. TE10 and TE01 B. TEM and TE01 C. TM01 and TEM D. TE10 and TEM [
Answer All Questions. All Questions Carry Equal Marks.Time: 20 Min. Marks: 20.
2.
In a rectangular waveguide, which of the following modes are known as the degenerate modes [ A. TE01 and TE10 B. TE11 and TM11 C. TM01 and TM10 D. TE01 and TM01 A rat race microwave circuit is the popular name for. A. E Plane Tee B. H Plane Tee C. Magic Tee D. Hybrid Ring
3.
4.
For microstrip lines, as the ratio W/h increases the dielectric attenuation factor ___ and the conductor attenuation factor [ ] A. Increases, increases B. Decreases, decreases C. Increases, decreases D. decreases, increases For a wide microstrip line, Zo is proportional to. _____, where h is the substrate thickness and W is the width of the strip. [ ] A. h W B. W/ h C. h /W D.1/ (W h) A tuning screw having a quarter wavelength depth of penetration in a rectangular guide represents in shunt. [ ] A. An inductance B. S capacitance C. A series resonant circuit D. A shunt resonant circuit In microwave frequencies, the specific resistivities of ferrites are. B. > 10 9 cm C. > 1012 cm D. > 1015 cm A. > 10 6 cm
5.
6.
7.
T N
W U
R O
D L
8.
In a cylindrical waveguide, the cut-off frequency of any TM mode is dependent on the medium permittivity () as. [ ] A. Proportional to B. Inversely proportional to C. proportional to D. inversely proportional to A full length thin circular post at the centre of the broad wall (parallel to the narrow wall) of a rectangular guide represents __________in shunt. [ ] A. An inductance B. A capacitance C. A shunt resonant circuit D. A series resonant circuit Cont..2
9.
www.jntuworld.com
www.jntuworld.com
:2:
Set No.1 [ ]
An ideal directional coupler has _______ directivity, and ___________ insertion loss. A. Infinity, zero B. Zero, zero C. Zero, infinity D. Infinity, infinity Fill in the blanks: H-plane T-junction is an______________, and is also known as a shunt Tee. ____________ involves both electric and magnetic coupling features. A 2-port device with S21 = 1 and S12 = 0 can be designated as _________
The dominant mode attenuation factor due to finite conductivity () of the waveguide walls is proportional to___________ At the cut-off frequency, the dominant mode characteristic impedance of a rectangular waveguide is ___________ At the cut-off frequency, the TM11 mode characteristic impedance of a rectangular waveguide is _________ ohms. If the input power of a 20 dB coupler is 20 mW, the output power at the coupled port will be _________ mW. Typical frequency range of X-band is _______G Hz The VSWR of an ideal matched load is ________
15.
16.
17.
The output power of a 20 dB matched waveguide attenuator, having an input of 10 mW is _________ mW.
T N
W U
-oOo-
R O
D L
www.jntuworld.com
www.jntuworld.com Code No: A107320402 Set No. 2 JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY HYDERABAD III B.Tech. II Sem., I Mid-Term Examinations, February 2011 MICROWAVE ENGINEERING Objective Exam Name: ______________________________ Hall Ticket No. A I 1. Choose the correct alternative: For microstrip lines, as the ratio W/h increases the dielectric attenuation factor ___ and the conductor attenuation factor [ ] A. Increases, increases B. Decreases, decreases C. Increases, decreases D. decreases, increases For a wide microstrip line, Zo is proportional to. _____, where h is the substrate thickness and W is the width of the strip. [ ] A. h W B. W/ h C. h /W D.1/ (W h) A tuning screw having a quarter wavelength depth of penetration in a rectangular guide represents in shunt. [ ] A. An inductance B. S capacitance C. A series resonant circuit D. A shunt resonant circuit In microwave frequencies, the specific resistivities of ferrites are. A. > 10 6 cm B. > 10 9 cm C. > 1012 cm D. > 1015 cm
Answer All Questions. All Questions Carry Equal Marks.Time: 20 Min. Marks: 20.
2.
3.
4.
5.
In a cylindrical waveguide, the cut-off frequency of any TM mode is dependent on the medium permittivity () as. [ ] A. Proportional to B. Inversely proportional to C. proportional to D. inversely proportional to A full length thin circular post at the centre of the broad wall (parallel to the narrow wall) of a rectangular guide represents __________in shunt. [ ] A. An inductance B. A capacitance C. A shunt resonant circuit D. A series resonant circuit An ideal directional coupler has _______ directivity, and ___________ insertion loss. A. Infinity, zero B. Zero, zero C. Zero, infinity D. Infinity, infinity Which of the following modes are impossible in a circular waveguide? B. TEM and TE01 C. TM01 and TEM D. TE10 and TEM A. TE10 and TE01 [ ]
6.
T N
W U
R O
D L
7.
8.
9.
In a rectangular waveguide, which of the following modes are known as the degenerate modes [ A. TE01 and TE10 B. TE11 and TM11 C. TM01 and TM10 D. TE01 and TM01
Cont..2
www.jntuworld.com
www.jntuworld.com
:2:
Set No.2
10.
A rat race microwave circuit is the popular name for. A. E Plane Tee B. H Plane Tee C. Magic Tee D. Hybrid Ring
II 11.
Fill in the blanks: The dominant mode attenuation factor due to finite conductivity () of the waveguide walls is proportional to___________ At the cut-off frequency, the dominant mode characteristic impedance of a rectangular waveguide is ___________ At the cut-off frequency, the TM11 mode characteristic impedance of a rectangular waveguide is _________ ohms. If the input power of a 20 dB coupler is 20 mW, the output power at the coupled port will be _________ mW. Typical frequency range of X-band is _______G Hz The VSWR of an ideal matched load is ________
12.
13.
14.
The output power of a 20 dB matched waveguide attenuator, having an input of 10 mW is _________ mW. H-plane T-junction is an______________, and is also known as a shunt Tee. ____________ involves both electric and magnetic coupling features. A 2-port device with S21 = 1 and S12 = 0 can be designated as _________
T N
W U
-oOo-
R O
D L
www.jntuworld.com
www.jntuworld.com Code No: A107320402 Set No. 3 JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY HYDERABAD III B.Tech. II Sem., I Mid-Term Examinations, February 2011 MICROWAVE ENGINEERING Objective Exam Name: ______________________________ Hall Ticket No. A I 1. Choose the correct alternative: A tuning screw having a quarter wavelength depth of penetration in a rectangular guide represents in shunt. [ ] A. An inductance B. S capacitance C. A series resonant circuit D. A shunt resonant circuit In microwave frequencies, the specific resistivities of ferrites are. B. > 10 9 cm C. > 1012 cm D. > 1015 cm A. > 10 6 cm [ ]
Answer All Questions. All Questions Carry Equal Marks.Time: 20 Min. Marks: 20.
2.
3.
In a cylindrical waveguide, the cut-off frequency of any TM mode is dependent on the medium permittivity () as. [ ] A. Proportional to B. Inversely proportional to C. proportional to D. inversely proportional to A full length thin circular post at the centre of the broad wall (parallel to the narrow wall) of a rectangular guide represents __________in shunt. [ ] A. An inductance B. A capacitance C. A shunt resonant circuit D. A series resonant circuit An ideal directional coupler has _______ directivity, and ___________ insertion loss. A. Infinity, zero B. Zero, zero C. Zero, infinity D. Infinity, infinity Which of the following modes are impossible in a circular waveguide? A. TE10 and TE01 B. TEM and TE01 C. TM01 and TEM D. TE10 and TEM
4.
5.
6.
7.
In a rectangular waveguide, which of the following modes are known as the degenerate modes [ B. TE11 and TM11 C. TM01 and TM10 D. TE01 and TM01 A. TE01 and TE10 A rat race microwave circuit is the popular name for. A. E Plane Tee B. H Plane Tee C. Magic Tee D. Hybrid Ring [
T N
W U
R O
D L
8.
9.
For microstrip lines, as the ratio W/h increases the dielectric attenuation factor ___ and the conductor attenuation factor [ ] A. Increases, increases B. Decreases, decreases C. Increases, decreases D. decreases, increases
Cont..2
www.jntuworld.com
www.jntuworld.com
:2:
Set No.3
10.
For a wide microstrip line, Zo is proportional to. _____, where h is the substrate thickness and W is the width of the strip. [ ] A. h W B. W/ h C. h /W D.1/ (W h)
II 11.
Fill in the blanks: At the cut-off frequency, the TM11 mode characteristic impedance of a rectangular waveguide is _________ ohms. If the input power of a 20 dB coupler is 20 mW, the output power at the coupled port will be _________ mW. Typical frequency range of X-band is _______G Hz The VSWR of an ideal matched load is ________
12.
The output power of a 20 dB matched waveguide attenuator, having an input of 10 mW is _________ mW. H-plane T-junction is an______________, and is also known as a shunt Tee. ____________ involves both electric and magnetic coupling features. A 2-port device with S21 = 1 and S12 = 0 can be designated as _________ The dominant mode attenuation factor due to finite conductivity () of the waveguide walls is proportional to___________ At the cut-off frequency, the dominant mode characteristic impedance of a rectangular waveguide is ___________
20.
T N
W U
-oOo-
R O
D L
www.jntuworld.com
www.jntuworld.com Code No: A107320402 Set No. 4 JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY HYDERABAD III B.Tech. II Sem., I Mid-Term Examinations, February 2011 MICROWAVE ENGINEERING Objective Exam Name: ______________________________ Hall Ticket No. A I 1. Choose the correct alternative: In a cylindrical waveguide, the cut-off frequency of any TM mode is dependent on the medium permittivity () as. [ ] A. Proportional to B. Inversely proportional to C. proportional to D. inversely proportional to A full length thin circular post at the centre of the broad wall (parallel to the narrow wall) of a rectangular guide represents __________in shunt. [ ] A. An inductance B. A capacitance C. A shunt resonant circuit D. A series resonant circuit An ideal directional coupler has _______ directivity, and ___________ insertion loss. A. Infinity, zero B. Zero, zero C. Zero, infinity D. Infinity, infinity Which of the following modes are impossible in a circular waveguide? A. TE10 and TE01 B. TEM and TE01 C. TM01 and TEM D. TE10 and TEM
Answer All Questions. All Questions Carry Equal Marks.Time: 20 Min. Marks: 20.
2.
3.
4.
5.
In a rectangular waveguide, which of the following modes are known as the degenerate modes [ A. TE01 and TE10 B. TE11 and TM11 C. TM01 and TM10 D. TE01 and TM01 A rat race microwave circuit is the popular name for. A. E Plane Tee B. H Plane Tee C. Magic Tee D. Hybrid Ring
6.
7.
For microstrip lines, as the ratio W/h increases the dielectric attenuation factor ___ and the conductor attenuation factor [ ] A. Increases, increases B. Decreases, decreases C. Increases, decreases D. decreases, increases For a wide microstrip line, Zo is proportional to. _____, where h is the substrate thickness and W is the width of the strip. [ ] A. h W B. W/ h C. h /W D.1/ (W h) A tuning screw having a quarter wavelength depth of penetration in a rectangular guide represents in shunt. [ ] A. An inductance B. S capacitance C. A series resonant circuit D. A shunt resonant circuit Cont..2
T N
W U
R O
D L
8.
9.
www.jntuworld.com
www.jntuworld.com
:2:
Set No.4 [ ]
In microwave frequencies, the specific resistivities of ferrites are. B. > 10 9 cm C. > 1012 cm D. > 1015 cm A. > 10 6 cm
Fill in the blanks: Typical frequency range of X-band is _______G Hz The VSWR of an ideal matched load is ________ The output power of a 20 dB matched waveguide attenuator, having an input of 10 mW is _________ mW. H-plane T-junction is an______________, and is also known as a shunt Tee. ____________ involves both electric and magnetic coupling features.
The dominant mode attenuation factor due to finite conductivity () of the waveguide walls is proportional to___________ At the cut-off frequency, the dominant mode characteristic impedance of a rectangular waveguide is ___________ At the cut-off frequency, the TM11 mode characteristic impedance of a rectangular waveguide is _________ ohms. If the input power of a 20 dB coupler is 20 mW, the output power at the coupled port will be _________ mW. -oOo-
18.
19.
20.
T N
W U
R O
D L
www.jntuworld.com