Pyle Chopper series amplifiers are designed from the ground up to deliver the power, performance and flexibility the modern car audio enthusiast demands. The PLA-1200, PLA-2230, PLA-2260, and PLA-4120 are available now.
Pyle Chopper series amplifiers are designed from the ground up to deliver the power, performance and flexibility the modern car audio enthusiast demands. The PLA-1200, PLA-2230, PLA-2260, and PLA-4120 are available now.
Pyle Chopper series amplifiers are designed from the ground up to deliver the power, performance and flexibility the modern car audio enthusiast demands. The PLA-1200, PLA-2230, PLA-2260, and PLA-4120 are available now.
on your purchase of a Pyle Chopper Series amplifier.
This amplifier extends the Pyle tradition into a totally new series of amps, designed from the ground up to deliver the power, performance and flexibility the modern car audio enthusiast demands. When you check the list of features offered by the PLA-1200, PLA-2230, PLA-2260, and PLA-4120 youll know you made the right choice with a Pyle Chopper amplifier. 2/ 4 channel input connections P L A -4120 14 P L A -2230/ P L A -226 0 general features 2-3 speaker connections P L A -4120 system wiring P L A -1200 system wiring speaker connections 17 table of contents features and specifications mounting and installation 21 protection circuitry and troubleshooting 22 15 16 18-19 mono input connections P L A -4120 high lev el input connections P L A -4120 precautions 23 mono input connections P L A -2230/ P L A -226 0 13 stereo input connections P L A -2230/ P L A -226 0 12 electrical connections P L A -1200/ 2230/ 226 0 P L A -4120 10 P L A -1200 P L A -2230/ P L A -226 0 P L A -4120 4-5 6-7 8-9 11 20 1 Mono Block Subwoofer Amplifier 1 Ohm Stable MOSFET Power Supply PWM (Puls e-Width-Modulation) Sys tem Glas s Epoxy PCB Gold Plated RCA Inputs for Line Input & Bypas s Output. Gold Plated Terminals for Speaker Output and Power Input. Thermal, Overload and Short Protection Variable Bas s Boos t Variable Sub-s onic Filter (15Hz~40Hz, 24dB/Octave) Variable Low-pas s Filter (20Hz~250Hz, 24dB/Octave) Phas e Control 0-180 degree Remote Bas s Control Input Impedance : 10K Ohms Soft Turn On/Off Advanced Protection Circuitry S/N Ratio:>90dB Heavy Duty Power Coated Heats ink P L A -1200 1900W Mono Bloc k MOSFET Amplifie r 1500 Watts x 2 Output 3000 Watts x 1 Bridged Output Variable Hi/Lo Electronic Cros s over Network Variable Input Level (Gain) Control Sub Sonic Filter Variable Bas s Boos t Thermal / Overload / Short Circuit Protection MOSFET PWM Power Supply Power & Protection LED Indicators Low Level Inputs Gold Plated RCA Inputs & Outputs Slim Size Amplifier Des ign For Eas y Ins tallation Remote Turn On/Off Soft Turn-On Circuit Anti-Thump Turn-On S/N Ratio:>95dB T.H.D:<0.04% FREQ. RESPONSE:15Hz- 30kHz P L A -2230 High Pe rforma nc e 3000 Wa t t 2 Cha nne l High Powe r MOSFET Amplifie r 2 general features 2000 Watts x 2 Output 4000 Watts x 1 Bridged Output Variable Hi/Lo Electronic Cros s over Network Variable Input Level (Gain) Control Sub Sonic Filter Variable Bas s Boos t Thermal / Overload / Short Circuit Protection MOSFET PWM Power Supply Power & Protection LED Indicators Low Level Inputs Gold Plated RCA Inputs & Outputs Slim Size Amplifier Des ign For Eas y Ins tallation Remote Turn On/Off Soft Turn-On Circuit Anti-Thump Turn-On S/N Ratio:>95dB T.H.D:<0.04% FREQ. RESPONSE:15Hz- 30kHz P L A -226 0 High Pe rforma nc e 4000 Wa t t 2 Cha nne l High Powe r MOSFET Amplifie r 250 Watts x 4 Output 500 Watts x 2 Bridged Output ( 250 x 2 + 500W x 1) Dual Variable Hi/Lo Electronic Cros s over Network Dual Switchable Bas s Boos t Dual MOSFET PWM Power Supplies Variable Input Level (Gain) Control Thermal / Overload / Short Circuit Protection Power & Protection LED Indicators Low Level Inputs Gold Plated RCA Inputs & Outputs Slim Size Amplifier Des ign For Eas y Ins tallation Remote Turn On/Off Soft Turn-On Circuit Anti-Thump Turn-On Tri-Mode Configurable S/N Ratio:>95dB T.H.D:<0.04% FREQ. RESPONSE:15Hz- 30kHz 3 P L A -4120 High Pe rforma nc e 1000 Wa t t 4 Cha nne l High Powe r MOSFET Amplifie r general features 4 fre que nc y re s pons e out put powe r @ 14.4v DC, 50Hz RMS Powe r at @ 4 Ohms RMS Powe r at @ 2 Ohms RMS Powe r at @ 1.3 Ohms Maximum Powe r Out put 200W MONO 350W MONO 600W MONO 1900W MONO 20 Hz- 250 Hz (- 3dB) input impe da nc e 10K Ohms Stiffly regulated PWM power s upplies . MOSFET s witches maintain rated power over a wide range of battery voltages . When the s ub s onic s elector s witch is in "ON" mode, this filter control permits continuous ly variable adjus tment from 10 to 100Hz. This control permits adjus tment of the bas s level up to an increas e of approximately up to 18dB. Adjus table from 20Hz to 250Hz with a s lope of 24dB per octave.This allows for the adjus tment of the upper point of the frequency bandwidth and the res pective s ubwoofer. Adjus table from 15Hz to 40Hz with a s lope of 24dB per octave.This allows for the attenuation of frequencies that are mos tly inaudible and caus e unneces s ary s train on the amplifier. Protection agains t thermal, overload and s hort circuit conditions . This amplifier come complete with a compact remote GAIN CONTROLLER which can be conveniently mounted on or under the das hboard of your car. powe r s upplie s s ub s onic c ont rol ba s s boos t le ve l c ont rol c ros s ove r low pa s s filt e r high pa s s s ubs onic filt e r prot e c t ion c irc uit ry re mot e da s h-mount ga in c ont rol input s e ns it ivit y powe r s upply volt a ge 14.4V DC Neg. Ground (10.5- 16V) dime ns ions (W x H x L) mm inc he s 2- 4 Ohm min s pe a ke r lmpe da nc e 20A x 2 270 x 36 x 305 10.63 x 1.42 x 12 T.H.D S/N ra t ion fus e >90dB 0.1% 250mV~4V Adjus table PLA- 1200 features and specifications M ONO BL OCK A M P L IF IER P L A -120 0 P L A -1200 5 features and controls M ONO BL OCK A M P L IF IER P L A -120 0 When us ed with normal, full range s ys tem, s et this s witch to "FULL" . If you wis h to us e the internal cros s over to power a driver or s pecific frequency range, us e the "LPF"or "HPF" FOR the "LOWPASS" OR HIGHPASS" s ettings . Enables the matching of input levels to the output levels from head unit (or other s ignal s ource). The input s ens itivity of adjus tment ranges from 6V to 200mV. When cros s over mode s elector is in HIGHPASS mode, this control s ets the lower frequency limit for audio program s ent to the s peakers . When cros s over mode s elector is in LOWPASS mode, this control s ets the upper frequency limit for audio program s ent to the s peakers . The cros s over is continuous ly variable adjus tment from 40 t0 250 Hz. This s elector s witch permits the bas s level an increas e of 18dB. This control permits adjus tment of the bas s level up to an increas e of approximately up to 18dB. When the s ub s onic s elector s witch is in "ON" mode, this filter control permits continuous ly variable adjus tment from 10 to 100Hz. c ros s ove r mode s e le c t or input le ve l c ont rols c ros s ove r fre que nc y c ont rol ba s s boos t le ve l s e le c t or ba s s boos t le ve l c ont rol s ub s onic c ont rol This amp features gold-plated RCA type jacks for high impedance input. Us e thes e with car s tereo output which us es RCA type connector cables . If your car s tereo jacks RCA type output, us e this adaptor to connect the high-low level input adaptor to connect the s peaker output leads of car s tereo and the RCA input jacks of amp. This amp features gold-plated RCA jacks for AUX line outputs . Us e thes e outputs . Us e thes e for unlimited s ys tem expans ion to the next CHOPPER. This indicator is illuminated in GREEN when power is applied. This indicator is illuminated in RED when the built-in protection circuitry is actirated. The fus e protects the amplifier and your car' s electrical s ys tem from s hort circuit conditions . Us e thes e connectors to deliver power, ground, and remote turn-on control to the amplifier. Thes e terminals are 14K gold plated to guarantee high conductivity and minimum s ignal los s . low le ve l input high le ve l input AUX line out put s powe r LED prot e c t ion LED powe r fus e powe r t e rmina ls s pe a ke r c onne c t ors fre que nc y re s pons e out put powe r @ 14.4v DC, 1KHz RMS Powe r @ 4 Ohms THD @ 4 Ohms RMS Powe r @ 2 Ohms THD @ 2 Ohms Maximum Powe r Out put bridge d Powe r at 4 Out put input s e ns it ivit y low le ve l input s input impe da nc e low le ve l input s bas s boos t maximum c urre nt draw dime ns ions (W x H x L) mm inc he s mat c hing s pe ak e r impe danc e s t e re o mode bridge d mode S/N rat ion >95dB c hanne l s e parat ion c ros s ove r f ilt e rs >65dB 40 Hz- 250 Hz 40 Hz- 250 Hz low Pas s high Pas s powe r s upply volt age 14.4V DC Neg. Ground (10.5-16V) 200 Watts x 2 00 Watts x 2 00 Watts x 2 00 Watts x 2 1500 Watts x 2 3000 Watts x 1 15 Hz- 30 KHz 250mV 10K Ohms 300 Watts x 2 00 Watts x 2 00 Watts x 2 00 Watts x 2 2000 Watts x 2 4000 Watts x 1 PLA- 2230 PLA- 2260 0~ +18dB 2- 4 Ohms 4- 8 Ohms 00Ax2 270 x 36 x 432 10.63 x 1.42 x 17 00Ax2 270 x 36 x 532 10.63 x 1.42 x 21 features and specifications 2 ch a mp P L A -2230 P L A -226 0 6 2 ch a mp P L A -2230 P L A -226 0 P L A -2230 P L A -226 0 7 features and controls fre que nc y re s pons e out put powe r @ 14.4v DC, 1KHz RMS Powe r @ 4 Ohms THD @ 4 Ohms RMS Powe r @ 2 Ohms THD @ 2 Ohms Maximum Powe r Out put bridge d Powe r at 4 Out put input s e ns it ivit y low le ve l input s input impe da nc e low le ve l input s This amp features gold-plated RCA type jacks for high impedance input. Us e thes e with car s tereo output which us es RCA type connector cables . If your car s tereo jacks RCA type output, us e this adaptor to connect the high-low level input adaptor to connect the s peaker output leads of car s tereo and the RCA input jacks of amp. This amp features gold-plated RCA jacks for AUX line outputs . Us e thes e outputs . Us e thes e for unlimited s ys tem expans ion to the next CHOPPER. This indicator is illuminated in GREEN when power is applied. This indicator is illuminated in RED when the built-in protection circuitry is actirated. The fus e protects the amplifier and your car' s electrical s ys tem from s hort circuit conditions . Us e thes e connectors to deliver power, ground, and remote turn-on control to the amplifier. Thes e terminals are 14K gold plated to guarantee high conductivity and minimum s ignal los s . low le ve l input high le ve l input AUX line out put s powe r LED prot e c t ion LED powe r fus e powe r t e rmina ls s pe a ke r c onne c t ors bas s boos t maximum c urre nt draw dime ns ions (W x H x L) mm inc he s mat c hing s pe ak e r impe danc e s t e re o mode bridge d mode S/N rat ion >95dB c hanne l s e parat ion c ros s ove r f ilt e rs >65dB 40 Hz- 250 Hz 40 Hz- 250 Hz low Pas s high Pas s powe r s upply volt age 14.4V DC Neg. Ground (10.5-16V) When us ed with normal, full range s ys tem, s et this s witch to "FULL" . If you wis h to us e the internal cros s over to power a driver or s pecific frequency range, us e the "LPF"or "HPF" FOR the "LOWPASS" OR HIGHPASS" s ettings . Enables the matching of input levels to the output levels from head unit (or other s ignal s ource). The input s ens itivity of adjus tment ranges from 6V to 200mV. When cros s over mode s elector is in HIGHPASS mode, this control s ets the lower frequency limit for audio program s ent to the s peakers . When cros s over mode s elector is in LOWPASS mode, this control s ets the upper frequency limit for audio program s ent to the s peakers . The cros s over is continuous ly variable adjus tment from 40 t0 250 Hz. This s elector s witch permits the bas s level an increas e of 18dB. This control permits adjus tment of the bas s level up to an increas e of approximately up to 18dB. When the s ub s onic s elector s witch is in "ON" mode, this filter control permits continuous ly variable adjus tment from 10 to 100Hz. c ros s ove r mode s e le c t or input le ve l c ont rols c ros s ove r fre que nc y c ont rol ba s s boos t le ve l s e le c t or ba s s boos t le ve l c ont rol s ub s onic c ont rol 15 Hz- 30 KHz 250mV 10K Ohms 35Watts x 4 00 Watts x 4 00 Watts x 4 00 Watts x 4 250 Watts x 4 500 Watts x 2 PLA- 4120 0~ +18dB 2- 4 Ohms 4- 8 Ohms 20Ax2 270 x 36 x 330 10.63 x 1.42 x 13 features and specifications 4 ch a mp P L A -4120 8 P L A -4120 9 18dB 0dB HPF LPF FULL HPF LPF FULL 18dB 0dB BASSBOOST X-OVER BASSBOOST X-OVER CH1/ 2 CH3/ 4 features and controls 4 ch a mp P L A -4120 P L A -2230 P L A -226 0 10 2 ch a mp P L A -2230 P L A -226 0 electrical connections P L A -4120 11 electrical connections 4 ch a mp P L A -4120 12 P L A -2230 P L A -226 0 stereo input connections 2 ch a mp P L A -2230 P L A -226 0 13 P L A -2230 P L A -226 0 mono input connections 2 ch a mp P L A -2230 P L A -226 0 P L A -4 12 0 14 4 ch a mp P L A -4120 2/ 4 channel input connections 4 CHfloating ground connections P L A -4120 15 4 ch a mp P L A -4120 high lev el input connections P L A -4120 16 4 CHmono input connections using low level inputs 2 CHmono input connections using low level inputs 4 ch a mp P L A -4120 mono input connections 17 Stereo Output Mode P L A -2230 P L A -226 0 Bridged Mono Output Mode speaker connections 2 ch a mp P L A -2230 P L A -226 0 P L A -4120 18 4 CHOutput Mode Bridged Dual Mono Output Mode speaker connections 4 ch a mp P L A -4120 P L A -4120 19 2 CHStereo Output Mode with Mono Bridged Subwoofer Output speaker connections 4 ch a mp P L A -4120 P L A-12 0 0 20 MONO BL OCK A MP L IF IER P L A -1200 system wiring 2 1 mounting Your new Pyle Chopper Series amplifier comes complete with all required mounting hardware. When determining a s uitable location in your vehicle for the amp, pleas e remember that it is a high- power electronic device capable of generating high heat. For this reas on, a lwa ys c hoos e a loc a t ion in your ve hic le whic h ha s low vibra t ion, a de qua t e ve nt ila t ion, a minimum of dus t , a nd no mois t ure . Be s ure to mount the amp in s uch a manner as to allow reas onable airflow over the cooling fins . Ma rk t he loc a t ion for t he mount ing s c re w hole s by pos itioning the amp where you wis h to ins tall it and us e a s cribe (or one of the mounting s crews ) ins erted in each of the mounting holes to mark the mounting s urface. If the mounting s urface is carpeted, meas ure the hole centers and mark with a felt tip pen. Be fore a t t e mpt ing t o drill t he mount ing hole s , t a ke not e of a ny wire s , line s or ot he r de vic e s in your ve hic le whic h ma y be loc a t e d be hind t he mount ing s urfa c e ! Then drill pilot holes in the mounting s urface for the mounting s crews and ins ert them. Tighten the s crews s ecurely. fuses wiring tips Whe n ma king e le c t ric a l c onne c t ions t o your a mplifie r, ple a s e obs e rve t he following: Us e at leas t 8 gauge wire for power and ground connections . Wire the amplifier directly to the car battery. For the ground connection, us e the s hortes t pos s ible wire to a good chas s is ground point. Wire the Remote connection to the auto s tart lead of your head unit, equalizer or power antenna. About powe r fus e s : Pyle Chopper Series amplifiers feature built- in fus e s ys tems . Thes e fus es protect both the amplifier and the electrical s ys tem in your vehicle from fault conditions . If you ever need to replace the fus e in your Pyle Chopper Series amp, us e a fus e of exactly the s ame type and rating. A different type or rating of fus e may res ult in damage or fire. mounting and installation 22 The built- in protection circuitry in the Pyle Chopper Series amplifiers will dis able the amplifier if it s ens es an input overload, a s peaker s hort circuit, or extreme temperature conditions . When the protection circuit is activated by any of thes e conditions , the Protection LED will be illuminated. If this occurs , carefully ins pect the s ys tem to determine the s ource of the problem. If the s hutdown was a res ult of a thermal overload condition, allow the amplifier to cool down before attempting to res tart it. If the s hutdown was a res ult of an input overload, or s peaker s hort circuit, be s ure to correct the condition before res tarting. The amplifier can be res tarted by turning the remote power OFF and then ON again. No out put . Confirm that all terminal s trip connections are s ecure and tight. Check both in- line and built- in fus es . Both the +12V and the Remote terminals mus t have +12v referenced to chas s is ground. Confirm that the audio s ignal s ource (car radio, equalizer, etc.) is connected and is s upplying output s ignal. To check if the amp is s upplying s ignal, unplug the cables from the s ignal s ource (but leave them plugged into the amp). Briefly tap the center pin of each of the dis connected RCA plugs with your finger. This s hould produce a nois e (feedback) in your s peakers . Only one c ha nne l works . Confirm that all terminal s trip connections are s ecure and tight. Check the Balance control on the head unit (or other s ource) to verify that it is s et to its midpoint. If you are us ing the Low Level RCA input, revers e the input plugs at the amplifier (i.e., s witch the L with the R). If the channels which is s ilent s witches to the other s ide, the problem is either in the head unit/ other s ource or the connecting cables . We a k out put . Readjus t the Input Level Control(s ) to better s uit the input s ignal. Nois e in t he a udio. If the nois e is a whine whos e pitch follows the engine s peed, confirm that the amplifier and any other s ignal s ources (head unit, etc.) are properly grounded. If the nois e is a clicking or popping nois e whos e rate follows the engine s peed, this us ually means that the vehicle is equipped with res is tor s park plugs and wires , or that the ignition is in need of s ervice. Check the rounting of the s peaker and input wires to make s ure they are not adjacent to wires which interconnect lights and other acces s ories . If the above s teps fail to improve or clear nois e interference, the s ys tem s hould be checked by a profes s ional mobile audio ins taller. protection circuitry troubleshooting 23 STOP YES! NO! 2-c hannel Ampl i f i er (Operat i ng i n St ereo) 4 ohm 4 ohm Two 4-ohm speakers, wired in stereo, will present a 4-ohm load to each channel of the amplifier. Most two- channel amplifiers will work well in this configuration. Two 4-ohm speakers, wired in parallel to a bridged two-channel amplifier. will present a 2-ohm mono load to the amplifier. MOST TWO-CHANNEL AMPLIFIERS DO NOT SUPPORT 2-OHM MONO OPERATION! AMPLIFIER DAMAGE COULD RESULT! 4 ohm 4 ohm 2-c hannel Ampl i f i er (Operat i ng i n Bri dged Mono) STOP YES! NO! Four 4-ohm speakers, wired in stereo, will present a 4-ohm load to each channel of the amplifier. Most four- channel amplifiers will work well in this configuration. Four 4-ohm speakers, wired in parallel to a bridged four-channel amplifier, will present a 4-ohm mono load to the amplifier. MOST FOUR-CHANNEL AMPLIFIERS DO NOT SUPPORT 2-OHM MONO OPERATION! AMPLIFIER DAMAGE COULD RESULT! 4-c hannel Ampl i f i er (Operat i ng i n Bri dged Mono) 4 ohm 4 ohm 4 ohm 4 ohm 4-c hannel Ampl i f i er (Operat i ng i n St ereo) 4 ohm 4 ohm 4 ohm 4 ohm notes precautions Do not operate the amplifier when it is unmounted. Attach all audio s ys tem components s ecurely within the automobile to prevent damage, es pecially in an accident. Do not mount this amplifier s o that the wire connections are unprotected, or in a pinched condition, or likely to be damaged by nearby objects . Before making or breaking power connections in your s ys tem, dis connect the vehicle battery. Confirm that your head unit or other equipment is turned off while connecting the input jacks and s peaker terminals . If you need to replace the power fus e, do s o only with a fuse identical to that supplied with the amplifier. Us ing a fus e of a different type or rating may res ult in damage that is nt covered in the manufacturers warranty. All Pyle products are carefully cons tructed and thoroughly tes ted before s hipment. Products purchas ed in the USA are warranted to be free of defects in material and workmans hip for two (2) years from the date of purchas e. This warranty is limited to the original retail purchas e. Should the product fail due to factory defects in material or workmans hip, your unit will be repaired or replaced at the s ole dis cretion of Pyle. To obtain warranty s ervice you mus t firs t call our Cons umer Return Hotline number at (718) 236- 6948 to obtain a Return Authorization number. This R.A.# mus t appear on the outs ide of your package and on all paperwork relating to your return. When returning a product to us for warranty s ervice it mus t be carefully packed and s hipped prepaid to: You mus t a ls o inc lude t he following it e ms : A copy of your s ales receipt or other proof of purchas e A brief letter indicating the problem you are experiencing include in your letter your return addres s , daytime phone number, and R.A. number als o include a check or money order for $18.00 for return s hipping, handling, and ins urance, or provide your Vis a/ MC number with expiration date. R.A.# Pyle Se rvic e Ce nt e r 1600 63rd St re e t Brooklyn, NY 11204 Our obligation under this warranty is limited to the repair or replacement of the defective unit when it is returned to us prepaid. This warranty will be cons idered void if the unit was tampered with, improperly s erviced, or s ubject to mis us e, neglect, or accidental damage. limited warranty policy a m p l i f i e r s www.pyleaudio.com