Professional Documents
Culture Documents
30 IN.
20 Gauge
1-1/2 IN.
5/32, 11/64, and 7/32 IN.
1, 2, 3, 6, 8, and 10 IN.
Page 2
Item 5907
Item 5907
Page 3
Set up Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section
at the beginning of this manual including all text under
subheadings therein before set up or use of this product.
Note: For additional information regarding the parts listed in the following pages,
refer to PartsList and AssemblyDiagram near the end of this manual.
Functions
Upper
Braking
Dies (12-01
to 12-06)
Mounting
Apron (11)
Upper
Blade
(23a)
Figure 2
Figure 1
Mounting Holes
Page 4
Item 5907
Upper Braking
Die (12-01
to 12-06)
Figure 3
Moveable
Cutter
Plate
Item 5907
Page 5
Upper
Blade
(23a)
Lower
Blade
(23b)
Hex
Screws
(56)
Figure 4
1. Remove the Hex Screws(56) from
the Upper Cutting Blade(23a).
2. Remove the Upper Cutting Blade.
Figure 5
1. Remove the Hex Screws(58) from
the Lower Cutting Blade(23).
3. Align the Upper Cutting Blade so that it is flush 2. Remove the Lower Cutting Blade.
with the Apron(11) and secure with its Screws.
3. Replace the Lower Cutting Blade
and secure with the Hex Screws.
4. To adjust the Upper Blade:
Supporting Plate (22)
Figure 6
Nut (49)
Figure 7
a. Lower the Upper Cutting Blade
to its lowest position.
b. Loosen the two inset Hex Head Bolts(59)
located on the top of the Work Bench(2).
c. Adjust the Lower Cutting Blade by turning its
Adjustment Screws. The distance between
the Lower Cutting Blade and Upper
Cutting Blade should be 5to8percent
of the thickness of the workpiece.
d. Tighten the two inset Hex Head Bolts.
Item 5907
Operating Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section
at the beginning of this manual including all text under
subheadings therein before set up or use of this product.
Angle Bending
Upper Braking Die
(12-(01-06))
Upper
Blade
(23a)
Lower
Blade
(23b)
Apron (11)
Figure 8
Guide (16)
Item 5907
Figure 9
1. Mark the workpiece where you
want to bend the material.
2. Place the material above the Apron(11).
3. Align the bending mark with the front
edge of the Upper Braking Die.
4. Rotate the Handle(18) until the desired
angle has been formed. Use a protractor or
other measuring tool to ensure accuracy.
Page 7
Radius Bending
Adjusting
Screw (27)
IN
Figure 12
24
Rollers
(24,31 & 32)
Roller
Adjustment
Knob (25)
Figure 10
For cylinders, the bends are evenly
spaced, i.e. every bend is identical.
Figure 11
For cones, move one side of the stock out
farther than the other for every bend.
Page 8
Item 5907
Pan Forming
Pans of various sizes can be formed
with a maximum lip(side) of 1".
To form a pan:
Figure 13
1. Pre-measure and cut the material
before bending. Notch the corners
according to the desired lip height.
Figure 16
4. Repeat Step 3 for the third side.
5. Rotate to the final side, and insert the
workpiece between the dies. The formed
sides will be on the outside of the Die.
Figure 14
2. Insert the material between the Upper
Braking Die and the Apron. Bend the
material until a 90 angle has been formed.
Figure 17
6. Before bending, tap one corner
nearer to the middle of the machine.
Thiswill allow the material to clear the
Upper Braking Die when raised.
7. Bend the fourth side.
8. Using a block or piece of wood, tap the
corner of material back into place.
Pressing
Figure 15
3. Rotate the material 90 counterclockwise.
Allow the completed side to extend just
beyond the Die. Bend the second side.
Item 5907
Page 9
Page 10
Item 5907
Troubleshooting
Problem
Bend is distorted.
Possible Causes
Likely Solutions
Bending
1. Clamping pressure
1. Adjust clamping pressure so that the
tootight.
workpiece has little or no clamping
pressure at the outside edges of the tool.
2. Radius set back
too close.
Bend angle
doesnt match
from end to end.
Clamp misaligned.
Metal doesnt
cut evenly.
1. Blades dull.
2. Blade distance
needs adjustment.
Item 5907
Page 11
Parts List
Part
1
2
3
4
5
6
7
8
9
10
11
12-01
12-02
12-03
12-04
12-05
12-06
13
14
15
16
17
18
19
20
21
22
23a
23b
24
25
26
27
28
29
30
31
Page 12
Description
Left Frame
Work Bench
Crossbeam
Crank Arm
Right Frame
Bear Frame
Cover
Press Plate Bracket
Spring
Press Plate
Apron
Upper Braking Die 1"
Upper Braking Die 2"
Upper Braking Die 3"
Upper Braking Die 6"
Upper Braking Die 8"
Upper Braking Die 10"
Press Plate
Hex Head Bolt M10X65
Rolling Wheel
Guide
Adjustable Bolt
Handle
Positioning Bar
Positioner
Positioning Plate
Supporting Plate
Upper Cutting Blade
Lower Cutting Blade
Back Pressing Roller
Roller Adjuster Knob
Handle Knob
Adjusting Screw
Roll Bushing
Washer
Gear
Lower Pressing Roller
Qty
1
1
1
2
1
1
2
2
2
1
1
1
1
1
1
1
1
1
2
2
1
2
1
2
2
1
1
1
1
1
2
2
2
4
2
2
1
Part
32
33
34
35
36
37
38
39
40
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
62
63
64
65
66
67
68
69
70
71
Description
Qty
1
1
1
2
2
2
4
2
2
4
2
2
2
1
2
2
1
2
2
9
4
2
2
7
2
7
2
2
2
1
1
1
2
2
2
2
2
Item 5907
REV 12f
Item 5907
71
70
71
66
26 70
7
42 38
26
65
18
64
39
44
29
45
35
15
27
4 25
40
62 36
34
28
33
28
24
19
67 47
17
37
32
42
48
20
31
68
28
30
51
49 50
46
43
28 68
67
6
70
55
12 -6 12 -5
13
21
37 30
48
8 9
47
53
22
12 -4
50
63
56
12 -3
51
40 36
10
12 -1
52
5 27
12 -2
11 54
14 23a
25
69
70
59
53
17
54
15
23b
14
45
38
39 7
35 29
4 62
55
44
58
42
59
16
57
Assembly Diagram
Page 13
Page 14
Item 5907
Item 5907
Page 15
3491 Mission Oaks Blvd. PO Box 6009 Camarillo, CA 93011 (800) 444-3353