Professional Documents
Culture Documents
MRP Run Parallel Planning
MRP Run Parallel Planning
Basic Concept:
Planning Types:
Parallel planning can be started online, or in the background (batch) from a dispatcher server.
In operative planning:
MD01 and MDBT
In master production scheduling:
MD40 and MDBS
In long-term planning:
MS01 and MSBT
Task Handling:
This dispatcher server distributes individual packages to planning file entries in the individual
sessions/processes of the servers defined in Customizing (asynchronous RFC calls are used).
Each process plans its package, and when it has completed planning, sends the package and the
planning results back to the dispatcher server.
As soon as a process/task becomes free again, it is sent the next planning package, and so on and so
forth.
Note: If the overall planning run (as a background job!) terminates, refer to Note 217271 for possible
causes:
In this case, incorrect destinations were defined in Customizing tables. These entries have to
be corrected (as described in Note 217271).
Planning Hierarchy:
The planning packages are sorted by low-level code/material/plant.
Planning is performed on the basis of low-level code, i.e. tasks with a new low-level code are not sent
off until all of the tasks of the previous low-level code have been completed.
When planning with planning scope, all planning file entries with the same material are sent off in the
same package.
If an error arises when a planning package is being planned, the planning file entries in the package
are sent off again individually for planning.
Source Code:
Executing online (transactions MD01/MS01/MD40):
MD01 - Include MM61XI10_DO_MRP_PARALLEL, or
MD40 - Include MM61XI10_DO_MPS_PARALLEL, or
MS01 - Include MM61XI10_DO_LFR_PARALLEL, and
Screen 400 in program SAPMM61X (dispatcher screen with dispatcher in PBO)
Executing in background (transactions MDBT/MSBT/MDBS):
MDBT - RMMRP000 (batch report)
MDBS - RMMPS000 (batch report)
MSBT - RMMRP010 (batch report)
MRP MANUAL
PERFX
RUNCNTX
NREAD
Planning:
Dispatcher screen 400 or FORM DISPATCHER in MM61XF40_DISPATCHER
FORM routine CALL_TASK_DISPOSITION
Function module for asynchronous RFCs to the destination servers:
CALL FUNCTION 'MRP_MATERIAL_PARALLEL'
DESTINATION
taskx-desti
STARTING NEW TASK taskx-tname
PERFORMING get_results ON END OF TASK
EXPORTING
icm61x = cm61x
tindx = taskx-index
iplsc = plsc
user_key = rm61x-uxkey
user_par = rm61x-uxpar
TABLES
cm61d_tab = cm61d_tab
tplantx = plantx
perf_tab = perfy
nread_tab = nread
EXCEPTIONS communication_failure = 01
system_failure
= 02.
FORM routine for returning results at the end of the task:
FORM GET_RESULTS USING TASKNAME.
DATA: RECV
TYPE RECV.
DATA: H_STOPX LIKE CM61X-STOPX.
"HW 155335
*
CLEAR RECV.
IF KEEPING_TASK IS INITIAL.
RECEIVE RESULTS FROM FUNCTION 'MRP_MATERIAL_PARALLEL'
IMPORTING
TINDX = RECV-INDEX
RTIME = RECV-RTIME
ISTATS = RECV-STATN
STOPX = H_STOPX
"HW 155335
TABLES CM61D_TAB = RECV-CM61DX
TPLANTX = PLANTX
PERF_TAB = RECV-PERFY
NREAD_TAB = NREAD
EXCEPTIONS SYSTEM_FAILURE
= 1 MESSAGE RECV-MSGTX
COMMUNICATION_FAILURE = 2 MESSAGE RECV-MSGTX.
ELSE.
"Kontext erhalten
RECEIVE RESULTS FROM FUNCTION 'MRP_MATERIAL_PARALLEL'
KEEPING TASK
IMPORTING
TINDX = RECV-INDEX
RTIME = RECV-RTIME
ISTATS = RECV-STATN
STOPX = H_STOPX
"HW 155335
TABLES CM61D_TAB = RECV-CM61DX
TPLANTX = PLANTX
PERF_TAB = RECV-PERFY
NREAD_TAB = NREAD
EXCEPTIONS SYSTEM_FAILURE
= 1 MESSAGE RECV-MSGTX
COMMUNICATION_FAILURE = 2 MESSAGE RECV-MSGTX.
MRP MANUAL
ENDIF.
Planning a Material:
In function module: MRP_MATERIAL_PARALLEL:
IF CM61X-PLSCN IS INITIAL.
PERFORM BEARBEITEN_MATERIAL_BT USING USER_KEY USER_PAR
CHANGING STOPX_FLAG.
ELSE.
PERFORM BEARBEITEN_MATERIAL_LFRPL USING USER_KEY USER_PAR
CHANGING STOPX_FLAG.
ENDIF.
... the system notes the number of planning runs performed for a material/plant/MRP area combination
(of the same low-level code) in the current planning package, and writes this number to table
IRUNCNTX.
If more than 4 planning runs are performed for a material, the planning file entry in question is no
longer included in the internal planning file entries, which means that the planning of this planning file
key is terminated.
Note:
MRP MANUAL
Note:
Please check the customer system and make sure that the sequence correction regarding the
blocking of a material and the user exit check have been applied as described in Note 179476.
Other Notes dealing with user exits: 155335 and 156582.