Professional Documents
Culture Documents
Note: SYSWIN is provided without token or dongle only to program CPM1 and CPM1A.
For C-series, and CV series PLCs, token or dongle is necessary.
Command
Response
Dip Switch
Set to Host
RS232C Connector Configuration
RS−232C
Adapter
IBM PC/AT or Compatible CPM1A CPU RS−232C
Signal Pin Pin Signal
FG 1 1 FG
RD 2 2 SD
SD 3 3 RD
DIR 4 4 RS
SG 5 5 CS
DSR 6 6 ---
RS 7 7 ---
CS 8 8 ---
--- 9 9 SG
5-1
5. WINDOW BASED PROGRAMMING SOFTWARE-
SYSWIN
Installing SYSWIN Program
The CPM1A training kit comes with three SYSWIN installation disks. The SYSWIN
program can be setup in Windows 3.1 or 3.11, Window 95,98 or Window NT 4.0.
To install, select RUN from the START menu. The following dialog box will
appear, enter a:\setup.exe in the command line, click OK to execute and follow
the directions as they appear on the screen.
Once installation is completed, two Program Group icons will appear in the
Program Manager. The SYSWIN samples contains sample programs whereas
SYSWIN contains the necessary program to run SYSWIN. To execute SYSWIN,
double click on the SYSWIN icon.
5-2
5. WINDOW BASED PROGRAMMING SOFTWARE-
SYSWIN
SYSWIN Window
Drawing Tools
Ladder Programming
Workspace
Scroll Bar
Address Bar
Instant Help & Status
Bar
5-3
5. WINDOW BASED PROGRAMMING SOFTWARE-
SYSWIN
Instruction Codes
Connection
Diagram Address Instructio Data
n
00000 LD 000.0
Relay 1 0
00001 OR 010.0
000.00 000.01 010.00 0
00002 AND NOT 000.0
Ladder 1
010.00 Program 00003 OUT 010.0
0
00004 END
00005
00006
00007
ON
000.00
OFF Time
ON
000.01
OFF Time
ON 010.00
5-4
OFF Time
5. WINDOW BASED PROGRAMMING SOFTWARE-
SYSWIN
Select the symbol of ladder program ([F2], normally open contact) from the
drawing Toolbox on side of the SYSWIN window. Click on the symbol and move
the symbol to anywhere in the window and click to release. The address of the
contact must be specified and key into the address dialog box. In this example,
000.00 is entered.
The address of the specific contact will be labeled on top of each component as
shown.
Each particular model of PLC has its own address for input and output, check
the catalogue for each type of PLC. The address 000.00 represent address of
5-5
5. WINDOW BASED PROGRAMMING SOFTWARE-
SYSWIN
the contact, the first three zero represent the channel number and the other 2
zero after the decimal represent the particular bit of the channel.
Continue with the rest of the sample program by clicking on the respective
symbols from the Drawing Toolbox.
Drawin
g
Tool
Box
Add
Networ
k
Note that each line of the ladder program is classified as a network. So in order
to create another line, click the icon Add Network (Shift+F6) from the
5-6
5. WINDOW BASED PROGRAMMING SOFTWARE-
SYSWIN
Toolbox to insert another network. The dialog box shown below appear when
icon is clicked. Select below current network and click OK.
The same program will end with an end instruction line. In order to insert the
end command, click on the FUN icon on side of the window, move it to the
location to end the program, click to execute. A function dialog box appear,
To browse for the types of functions available, lick on the select button. The
select function box will be shown.
5-7
5. WINDOW BASED PROGRAMMING SOFTWARE-
SYSWIN
5-8
5. WINDOW BASED PROGRAMMING SOFTWARE-
SYSWIN
Uploading of program from PLC to PC is also possible. Select detect NOPs (no
operation) for the options as shown.
Note: All application examples in this manual can either be programmed using
window based SYSWIN Software or the Programming Console.
5-9