Professional Documents
Culture Documents
18
Data Sheet
SR
110
Load peaks SR
(occasional, brief loads)
up to 0.75 N/mm2 approx. 80 % 11
Compression hardness 3 0.02 N/mm2 EN ISO 844 1 at 10 % linear compression, 3rd load cycle
Compression set 2
< 5% EN ISO 1856 1
50 % deformation, 23 °C, 72 h, 30 min after removal of load
Dynamic modulus of elasticity 3 0.29 N/mm2 DIN 53513 1 at specific load of 0.018 N/mm2, 10 Hz
Dynamic shear modulus 0.12 N/mm2 DIN ISO 1827 1 at a pretension of 0.018 N/mm2, 10 Hz
1
Measurement / evaluation in accordance All information and data is based on our current knowledge. The data can be applied for calculations and as
with the relevant standard guidelines, are subject to typical manufacturing tolerances and are not guaranteed. Material properties as well
2
The measurement is performed on a as their tolerances can vary depending on type of application or use and are available from Getzner on request.
density-dependent basis with differing
test parameters Further information can be found in VDI Guideline 2062
3
Values apply to shape factor q = 3 (Association of German Engineers) as well as in glossary.
Further characteristic values on request. www.getzner.com
1
Sylomer® SR 18 SR
18
0.035
Quasi-static load deflection curve
measured with a loading rate of
0.030
12.5 mm 0.0018 N/mm2/s.
25 mm
37.5 mm
0.025
50 mm
Testing between flat and plane-paral-
lel steel plates, recording of 3rd load,
0.020 with filtered starting range in accor-
0.018 N/mm2
dance with ISO 844, testing at room
0.005
0
0 1 2 3 4 5 6 7 8 9 10
Deflection in mm
Modulus of elasticity
Dynamic range of use
Static range of use
Modulus of elasticity in N/mm2
0.8
0
0 0.005 0.010 0.015 0.020 0.025 0.030 0.035
Specific load in N/mm2
www.getzner.com
2
Natural frequencies
Specific load in N/mm2
0.035
Natural frequencies of a vibratory
system with a single degree of free-
0.030
dome, consisting of a mass and an
elastic bearing made of
0.025
Sylomer® SR 18 on a rigid surface.
0.018 N/mm2
0.020
12.5 mm
Parameter: thickness of
the Sylomer® bearing
0.005
0
5 10 15 20 25
Natural frequency of the system in Hz
100
Reduction of the transmitted me-
-40 dB/99 %
90
-35 dB/98 % chanical vibrations by implementa-
-30 dB/97 % tion of an elastic bearing consisting
80
-25 dB/94 % of Sylomer® SR 18 based on a stiff
70 subgrade.
-20 dB/90 %
30
0 dB/0 %
20
10
0
5 10 15 20 25
Natural frequency of the system in Hz
www.getzner.com
3
Influence of the shape factor
The graphs show the material properties at different shape factors.
Specific load in N/mm2
Change in deflection in %
0.020 30 %
25 %
0.019
20 %
0.018
15 %
0.017 10 %
5%
0.016
0%
0.015
-5 %
0.014 -10 %
0.3 1 3 6 0.3 1 3 6
Shape factor Shape factor
Fig. 5: Static range of use in relation to the shape factor Fig. 6: Deflection 4 in the relation to the shape factor
Change in dynamic modulus of elasticity in %
10 % 5%
0% 0%
-10 % -5 %
-20 % -10 %
-30 % -15 %
-40 % -20 %
DB SR 18 en © Copyright by Getzner Werkstoffe GmbH l 06-2019
0.3 1 3 6 0.3 1 3 6
Shape factor Shape factor
Fig. 7: Dynamic modulus of elasticity 4 at 10 Hz in Fig. 8: Natural frequency 4 in relation to the shape factor
relation to the shape factor
We reserve the right to amend the data.
4
Reference values: specific load 0.018 N/mm2, shape factor q = 3
Material properties can be determined using the online calculation program FreqCalc.
The program can be accessed via www.getzner.com (registration necessary).
AUSTRIA — Bürs GERMANY — Berlin — Munich — Stuttgart FRANCE — Lyon JORDAN — Amman
JAPAN — Tokyo INDIA — Pune CHINA — Beijing USA — Charlotte www.getzner.com
4