Professional Documents
Culture Documents
30
Data Sheet
Compression hardness 3
0.03 N/mm 2
EN ISO 844 1
at 10 % linear compression, 1st load cycle
Compression set 2 < 5% EN ISO 1856 25 % deformation, 23 °C, 72 h, 30 min after removal of load
Dynamic shear modulus 3 0.53 N/mm2 DIN ISO 1827 1 at a pretension of 0.03 N/mm2, 10 Hz
Specific volume resistivity > 1012 Ω·cm DIN IEC 60093 dry
1
Measurement/evaluation in accordance with the All information and data is based on our current knowledge. The data can be applied for
relevant standard calculations and as guidelines, are subject to typical manufacturing tolerances and are not
2
The measurement is performed on a density- guaranteed. Material properties as well as their tolerances can vary depending on type of
dependent basis with differing test parameters application or use and are available from Getzner on request.
3
Values apply to shape factor q = 3
4
Take account of heating caused by energy conversion Further information can be found in VDI Guideline 2062 (Association of German Engineers)
as well as in glossary. Further characteristic values on request.
www.getzner.com
1
Sylodamp® SP 30 SP
30
0.025
Quasi-static load deflection curve with
a loading rate of 1 % of the thickness
12.5 mm 25 mm 37.5 mm 50 mm of the unloaded sample per second.
0.020
Shape factor q = 3
0.010
0
0 1 2 3 4
Deflection in mm
Modulus of elasticity
3.0
0.012 N/mm2 tangential modulus from the load
30 Hz deflection curve. Dynamic modulus
2.5 of elasticity from sinusoidal excita-
tion at a vibration velocity of 100 dBv
re. 5·10-8 m/s (corresponding to a
2.0
vibration amplitude of 0.22 mm at
10 Hz
10 Hz and 0.08 mm at 30 Hz).
1.5
Measurement in accordance with
DIN 53513
1.0
Shape factor q = 3
Quasi-static
0.5
0
0 0.005 0.010 0.015 0.020 0.025
Specific load in N/mm2
www.getzner.com
2
Natural frequencies
Specific load in N/mm2
0.025
Natural frequencies of a vibratory
system with a single degree of free-
12.5 mm
0.020
dom, consisting of a mass and an
elastic bearing made of Sylodamp®
SP 30 on a rigid surface.
0.015
Parameter: thickness of the
0.012 N/mm2
25 mm Sylodamp®-bearing
0.010
Shape factor q = 3
50 mm
0.005
0
20 30 40 50 60 70
Natural frequency of the system in Hz
Energy absorption
20
impact load at an impact speed of up
18 to 5 m/s.
16
Drop impact test with a round, flat
50 mm
14 stamp, recording of the 1st load,
testing at room temperature.
12
37.5 mm
10 Parameter: thickness of the
Sylodamp®-bearing
8
25 mm
6
4 12.5 mm
0
20 30 40 50 60 70 80
Linear compression in %
www.getzner.com
3
Influence of the shape factor
The graphs show the material properties at different shape factors.
Specific load in N/mm2
Change in deformation in %
0.014 30 %
25 %
0.013
20 %
0.012
15 %
0.011 10 %
5%
0.010
0%
0.009
-5 %
0.008 -10 %
0.3 0.5 1 3 6 0.3 0.5 1 3 6
Shape factor Shape factor
Fig. 5: Static range of use in relation to the shape factor Fig. 6: Deflection 5 in relation to the shape factor
Change in natural frequencies in %
5%
Change in dynamic modulus of elasticity in %
10 %
5%
0% 0%
-5 %
-10 % -5 %
-15 %
-20 % -10 %
-25 %
-30 % -15 %
0.3 0.5 1 3 6 0.3 0.5 1 3 6
Shape factor Shape factor
Fig. 7: Dynamic modulus of elasticity 5 at 10 Hz in relation Fig. 8: Natural frequency 5 in relation to the shape factor
to the shape factor
DB SP 30 en © Copyright by Getzner Werkstoffe GmbH l 03-2018
5
Reference values: specific load 0.012 N/mm2, shape factor q = 3
Material properties can be determined using the online calculation program FreqCalc.
The program can be accessed via www.getzner.com (registration necessary).
Subject to change without notice.
AUSTRIA — Bürs GERMANY — Berlin — Munich — Stuttgart FRANCE — Paris — Lyon JAPAN — Tokyo INDIA — Pune
JORDAN — Amman CHINA — Beijing USA — Charlotte AUSTRALIA — Melbourne www.getzner.com
4