Professional Documents
Culture Documents
,R3E-AB0AB0RNB731-5-1,2014/02/03 1/9
CREATED 2014/02/03
UPDATED 2022/05/09
2. Hazards Identification
GHS Classification of the substance or mixture
This product is classified under hazardous according to JIS Z 7252: 2019 (Classification of chemicals based on
GHS).
Health Hazards
Carcinogenicity Category 2
Signal Word(s)
WARNING
Hazard statement(s)
Health Hazards
H351 Suspected of causing cancer
"AMILAN"GF-Reinforced Grade CM3004G-15 (A), CM3004G-15 B (A),TORAY INDUSTRIES,INC.,R3E-AB0AB0RNB731-5-1,2014/02/03 2/9
Precautionary statement
[Prevention]
P201 Obtain special instructions before use.
P202 Do not handle until all safety precautions have been read and understood.
P280 Wear (protective gloves/protective clothing/eye protection/face protection).
[Response]
P308+P313 IF exposed or concerned: Get medical advice/attention.
[Storage]
P405 Store locked up.
[Disposal]
P501 Dispose of contents/container in accordance with the local laws or regulations (-).
Other hazards which do not result in classification
Nothing in particular.
Major symptom and envisioned emergencies
No information available.
3. Composition/Information on Ingredients
Substance/Mixture Mixture
Product identity(chemical name, common name) Poly(hexamethylene adipamide) resin
Synonym(s) Polyamide-66 resin, Nylon-66 resin
Composition/information on ingredients
Chemical identity of the substance Poly(hexamethylene adipamide)
Content(%) 29-76
Ingredient type Constituent
Contribution to GHS classification Not contribute
Chemical property(chemical formula, [NH(CH2)6NHCO(CH2)4CO]n
structural formula)
CAS No. 32131-17-2
ENCS No.(Chemical Substances Control Law) 7-382
ISHL No.(Industrial Safety and Health Act) 7-382
Content(%) 4-10
Ingredient type Constituent
Contribution to GHS classification Contribute
Chemical property(chemical formula, Sb2O3
structural formula)
CAS No. 1309-64-4
ENCS No.(Chemical Substances Control Law) 1-543
ISHL No.(Industrial Safety and Health Act) 1-543
PRTR No. 31
Notifiable number for ISHL 38
4. First-aid measures
Inhalation
Remove victim to fresh air and keep at rest in a position comfortable for breathing.
Evacuate victim that inhaled gas from the molten polymer to fresh air.
Seek medical advice, if victim does not recover.
Skin contact
If a person touches the molten polymer, cool the affected part with fresh water.
Do not try to remove the polymer by force and seek medical advice if the person got burnt.
Eye contact
Remove contact lenses, if present and easy to do. Continue rinsing.
Rinse your eyes gently with clean water for at least 15 minutes. Consult a doctor to receive medical treatment as
soon as possible.
Do not let the victim rub his eyes/keep his eyes tightly closed.
Ingestion
Rinse your mouth with some water.
If you don't feel well, arrange for a medical evaluation.
Most important symptoms and effects, both acute and delayed
No information available.
Precautions required to protect first-aiders
No information available.
Notes for the doctor
No information available.
5. Firefighting measures
Suitable extinguishing media
Water spray/Water jet/Foam/Powder/Carbon dioxide (CO2)
Unsuitable extinguishing media
Nothing in particular.
"AMILAN"GF-Reinforced Grade CM3004G-15 (A), CM3004G-15 B (A),TORAY INDUSTRIES,INC.,R3E-AB0AB0RNB731-5-1,2014/02/03 4/9
Contact with the fibers may cause temporary irritation or itching to skin, eyes, nose or throat.
Sweep up and dispose of spilled resin to eliminate slipping hazard.
Do not pile up bags too high in order to avoid injury caused by falling of the product.
Proper hygiene measures
Wash hands before intermissions or and after work.
Do not eat or smoke while working.
Conditions for safe storage, including any incompatibilities
Proper storage condition
Follow fire defense law and local regulations for storage and handling.
Storage condition to avoid
Keep fire away.
Keep away from heat source, steam pipe and direct sunlight. Store in cool places.
Safe container materials
No information available.
Color
Beige, Black
Odor
characteristic odor(peculiar odor)
Melting point/freezing point
265°C
Boiling point or initial boiling point and boiling range
None
Flammability (solid, gas)
Not available.
Lower and upper explosion limit / flammability limit
Not available.
Flash point
Not available.
Auto-ignition temperature
>400°C
Decomposition temperature
No information available.
pH
Not applicable.
Kinematic viscosity
Not applicable.
Solubility
No information available.
Partition coefficient: n-octanol/water
No information available.
Vapour pressure
No information available.
Density and/or relative density
1.47-1.68
Relative vapour density
Not applicable.
Particle characteristics
Not applicable.
Other information
No information available.
However, no warranty is made with respect to its completeness and we assume no liability resulting from its use.
It is advised to make their own tests to determinate the safety and suitability of each such product or
combination for their own purposes.
Other information
Resin is usually safe itself, so as for the calculation of division, acute toxicity (oral) is calculated by LD50
as more than 10000.