Professional Documents
Culture Documents
50 PDF
50 PDF
AUTOMATED ASSEMBLY
Page: 1/5
Date: 31-AUG-2015
CAGGIATI ALESSANDRO - alessandro.caggiati@fcagroup.com
TPM
SERIO STEFANO - stefano.serio@fcagroup.com
Code
PURPOSE
To specify the dimensional, material and coating requirements for wide flange hexagon bolts used in
the manufacture of motor vehicles where automated assembly operations are envisaged.
Bolts are supplied in loaders or poured into vibratory hoppers from whence they are conveyed by
C
compressed air to assembly stations via a system of supply hoses.
Note: To prevent bolts from overturning in supply hoses and jamming the equipment, the following
Ch.
ratio shall be respected:
dc max.
<1
2
k+I
Edition
Supervisor
Author
F THE ITALIAN EDITION IS NOT AVAILABLE OR NOT UPDATED, THE ENGLISH EDITION IS THE VALID REFERENCE.
-- 08/03/00 Edition 2 Rewritten from the previous edition (Ed.1 Change.M).
Underhead angle changed (formerly 0 1 30)
Dimensions in mm
dr = rolling diameter
Dimension k2 measured from theoretic
diameter d2, is used to ensure constant head
height when driver incorporates magnetic grip.
Example of designation:
1/87701/21 Std.Sh. 10367/50 Wide flange hexagon bolt for automated assembly,size M6 x 16 8.8 Fe/Zn 7 IV.
b
I 125 24 28 32 36 40
I > 125 34 38 42 46
THIS DOCUMENT MUST NOT BE REPRODUCED OR CIRCULATED TO THE THIRD PARTIES
k I min. = 0,7 k min. This dimension delimits minimum effective drive head height, and is checked using gauge
shown on page 5.
Grade A bolts with ISO metric threads.
12 11,6 12,4
14 13,6 14,4 3 87700 10,55
16 15,6 16,4 3 87701 10,89
18 17,6 18,4 3 4 87719 21,18
20 19,6 20,4 3 4
22 21,6 22,4 3 87704 11,91 4 87721 22,61 4,5
25 24,6 25,4 3 12,32 4 87722 23,68 4,5
28 27,6 28,4 4 4 4,5 31,21
30 29,6 30,4 6 4 87723 25,46 4,5
32 31,6 32,4 3 8 4 4,5
35 34,5 35,5 6 11 7 4,5
40 39,5 40,5 11 16 5,75 12 8
45 44,5 45,5 16 21 10,75 17 30,81 6,75 13
48 47,5 48,5 19 24 13,75 20 9,75 16
50 49,5 50,5 21 26 15,75 22 11,75 18
55 54,4 55,6 26 31 20,75 27 16,75 23
60 59,4 60,6 31 36 25,75 32 21,75 28 15623
65 64,4 65,6 30,75 37 26,75 33 15624
70 69,4 70,6 35,75 42 31,75 38
75 74,4 75,6 40,75 47 36,75 43
80 79,4 80,6 45,75 52 41,75 48
90 89,3 90,7 51,75 58
F THE ITALIAN EDITION IS NOT AVAILABLE OR NOT UPDATED, THE ENGLISH EDITION IS THE VALID REFERENCE.
100 99,3 100,7 61,75 68
110 109,3 110,7
For bolts with M12 x 1,25 and M14 x 1,5 threads see page 4.
See: Std. 01307 Identification markings. Std. 01444 General requirements.
CONFIDENTIAL
Dimensions in mm
IMPORTANT: The adoption of this type of material does not always allow obtaining bolts that
THIS DOCUMENT MUST NOT BE REPRODUCED OR CIRCULATED TO THE THIRD PARTIES
In some cases it will not be possibile to obtain the underhead collar of 0,2 +0,1
0
WITHOUT PRIOR WRITTEN CONSENT BY FCA ITALY S.p.A.
Gauge A Gauge B
Nominal thread size
EA KA EB KB
d
max. min. max. min. max. min. min.
M6 11,56 11,55 2,50 2,49 10,94 10,93 3
F THE ITALIAN EDITION IS NOT AVAILABLE OR NOT UPDATED, THE ENGLISH EDITION IS THE VALID REFERENCE.
M14 x 1,5 24,26 24,25 5,10 5,09 23,14 23,13 5
Notes:
EA min. = Theoretic width across corners.
EB max. = Minimum width across corners (e min.) minus 0,01.
KA max. = Minimum drive height. (k').