Professional Documents
Culture Documents
TABLE OF CONTENT
DESCRIPTION PAGE
SURFACE EQUIPMENT
Blow Out Preventers 2
Manual Type 2
Hydraulic Type 3
Dual Hydraulic Type 4
BOP Technical Sheet 5
Control Head Assembly 6
Hydraulic Packing Nut BT 7
Tree Connections 8
Flange 10
Flow Tee - High Pressure 12
Flow Tee - Low Pressure 13
Fluid Chamber 14
4 TPI Hand Union 15
Hay Pulley 16
Lubricators 17
Lubricator Clamp 19
Pump-In Sub w/WECO Union 20
Quick Union 21
Riser - Dual .5" NPT 22
Stuffing Box 23
Tool Catcher 24
Wellhead Swedges 25
Counter Head Assembly 26
Line Wiper 27
Staff Assembly 28
Sucker Rod Pin x Box Chaser 29
Hydraulic Line Wiper Swab Head 29
Veeder Root 30
Weight Indicator 30
Counter Wheels 31
Pressure Wheels 31
Gin Pole 32
Gin Pole Step 32
Releasing Tool 33
PACKING
Packing 34
SLICKLINE & E-LINE STACK
CONFIGURATION
Stuffing Box
Head Catcher
Grease Head
Chemical Injection Sub
Lubricator
Head Catcher
Lubricator Bleed-Off
Tool Trap
Hydraulic BOP
Hydraulic BOP
Pump-In-Sub/Flow T
Pump-In-Sub/Flow T
E-LINE SLICKLINE
1
BLOW OUT PREVENTER
(MANUAL TYPE)
Purpose
To enable well pressure to be isolated and released from the lubricator without closing wellbore
valves.
Blowout Preventers are designed to give positive protection against blow outs when operating with
wireline in well services work, by providing a positive seal around wireline.
Description
The main body in the shape of a cross has a vertical full bore section to allow movement of wireline
tools in and out of the wellbore.
The horizontal ends of the cross often referred to as ram housing contain rams, with inner and outer
seals. These rams can be rotated in and out of the housing with handles fastened to threaded stems
for closing and opening ram bodies.
An equalizing assembly is located on the side of the main body with a bleed off port on the opposite
side, and located 90 degrees from ram housings. By opening an allen wrench operated valve seat the
equalizing assembly allows pressure to be returned to the lubricator from the wellbore with rams
closed.
BOP are fitted with compatible hand unions for installation with surface equipment. Wireline BOPs
seal and hold pressure from below only.
Blow Out Preventers are available in sizes ranging from 2-1/2" ID through 6-3/8" ID and 3000 PSI
through 15,000 PSI working pressure.
2
BLOW OUT PREVENTER
(HYDRAULIC TYPE)
This BOP's are available basically in two types: Hydraulically Operated and
Manually Operated, with configurations as desired. An equalizer valve
allows the operator to equalize the pressure with lubricator pressure.
3
BLOW OUT PREVENTER
(DUAL HYDRAULIC TYPE)
4
BLOW OUT PREVENTER
5
CONTROL HEAD ASSEMBLY
Purpose
Used to seal wireline or slickline in high pressure or volatile conditions.
Description
The Control Head is made up of 9 main components:
1. Female Bleed Collar
2. Flow Tube
3. Flow Tube Sleeve
4. Injection Collar
5. Bottom Sub
6. Ported Spacer Sub
7. Hand Union Nut
8. Ball Seat Retainer
9. Steel Ball
Part Number
Assembly OIL-CHAS-0000-0000-W01
6
HYDRAULIC PACKING NUT BT
Part Number
Assembly OIL-HPNBT-0000-0000-W01
COMPONENTS
Body
Plunger
Gland
Spring
Bottom Sub
Housing O-ring
Plunger O-ring
7
Cameron Acme
TREE CONNECTIONS
Pin x Threaded Half
Part Number
2 3/8" 8RD pin x 2 1/2" threaded half OIL-TC-2375P-25TH-W01
2 7/8" 8RD pin x 2 1/2" threaded half OIL-TC-2875P-25TH-W01
3 1/2" 8RD pin x 2 1/2" threaded half OIL-TC-3500P-25TH-W01
Cameron Acme (Above 4 3/4"-4 Bowen Type)
Sliding Sleeve
2 3/8" 8RD pin x 3" dbl. lead thrd. Half OIL-TC-2375P-3DTH-W01
2 7/8" 8RD pin x 3" dbl. lead thrd. half OIL-TC-2875P-3DTH-W01
3 1/2" 8RD pin x 3" dbl. lead thrd. half OIL-TC-3500P-3DTH-W01
(Above Bowen Type)
8
TREE CONNECTIONS
Cameron Acme
Pin x Threaded Half
Part Number
2 3/8" Cameron Acme pin x 2 1/2" thrd half OIL-TCCA-2375P-25TH-W01
2 7/8" Cameron Acme pin x 2 1/2" thrd half OIL-TCCA-2875P-25TH-W01
3 1/2" Cameron Acme pin x 2 1/2" thrd half OIL-TCCA-3500P-25TH-W01
Cameron Acme
Sliding Sleeve B-20 Gray Hub Tree Connection x 2 1/2" threaded
half OIL-TCB20-GH00-25TH-W01
C-25 Gray Hub Tree Connection x 2 1/2" threaded
half OIL-TCC25-GH00-0000-W01
D-31 Gray Hub Tree Connection x 2 1/2" threaded
half OIL-TCD31-GH00-0000-W01
E-25 Gray Hub Tree Connection x 2 1/2" threaded
half OIL-TCE25-GH00-0000-W01
9
FLANGE
Purpose
Connects wireline surface equipment to wellhead.
Description
The lower end of the Wellhead Flange is manufactured flanged to
match the particular configuration of the wellhead. The upper
end of the Flange is compatible to the bottom hand union of the
BOP or flow sub.
10
FLANGE
11
FLOW TEE HIGH PRESSURE
Purpose
Gives the ability to either pump into / or bleed off wellbore pressure
under high pressure.
Description
The Flow Tee HP consists of 6 components:
1. Flow Sub Body
2. Hand Nut
3. Bottom Union
4. Flow Sub to Nutron Valve Cross Over
5. Nutron Valve to 6K Guiberson Style Union
6. Nutron Ball Valve (not shown)
The High Pressure Flow Tee incorporates a 2 high pressure quarter
turn ball valve to allow rapid well control as well as a larger bore to
pump in / bleed off the well bore. The High Pressure Flow Tee also
utilizes (but is not limited to) a 6K Guiberson style union for ease of
use and capability of pressure
Precautions
Ensure proper care and maintenance as abrasive debris may damage
the ball seat if left unchecked.
Part Number
Assembly OIL-FTHP-0000-0000-W01
Please Specify The following When Flow Sub Body OIL-FTHP-0000-FSB0-W01
Ordering this Equipment: Hand Nut OIL-FTHP-0000-HN00-W01
Bottom Union OIL-FTHP-0000-BU00-W01
Union Type X-over to Nutron Valve OIL-FTHP-0000-XONV-W01
Working Pressure X-Over to Guiberson OIL-FTHP-0000-XOGB-W01
Ring Gasket
12
FLOW TEE LOW PRESSURE
Purpose
Gives the ability to either pump into / or bleed off wellbore pressure.
Description
The Flow Tee LP consists of 3 components:
1. Flow Sub Body
2. Hand Nut
3. Bottom Union
The Low Pressure Flow Tee incorporates a 2 line pipe port to allow rapid
well control as well as a larger bore to pump in / bleed off the well bore.
Precautions
Ensure threads are not worn or damaged.
Part Number
Assembly OIL-FTLP-0000-0000-W01
Flow Sub Body OIL-FTLP-0000-FSB0-W01
Hand Nut OIL-FTLP-0000-HN00-W01
Bottom Union OIL-FTLP-0000-BU00-W01
13
FLUID CHAMBER
Purpose
Gives the ability to pump any type of fluid desired, typically used to
pump oil into wellbore directly below the stuffing box to lubricate the
seals within.
Description
The fluid Chamber consists of 4 components:
1. Fluid Chamber Body
2. Gland
3. Hand Nut
4. Bottom Union
The Fluid Chamber incorporates a ported gland internally and a reservoir
that lubricant, methanol, or any desired fluid may be pumped into to
reduce icing, or line chatter, the liquid is installed via a .5 NPT port,
which is connected to a hose and pump.
Precautions
Ensure threads are not worn or damaged, it is recommended that a
check valve be installed in any hose or line that may contain wellbore
pressure.
Part Number
Assembly OIL-FLCH-0000-0000-W01
Fluid Chamber Body OIL-FLCH-BDY0-0000-W01
Gland OIL-FLCH-GL00-0000-W01
Hand Nut OIL-FLCH-HN00-0000-W01
Bottom Union OIL-FLCH-BU00-0000-W01
14
4 TPI HAND UNION
Purpose
The 4 TPI Hand Unions (Bowen style) 5k is used to allow easy assembly /
disassembly of lubricator and or surface equipment..
Description
Hand Unions are made up of 3 components:
1. Male Union Half
2. Hand Nut
3. Female Union Half
Applications
5k working pressure lubricator strings; Connections for bleed subs and / or
risers; Hand Unions are available with any number of connections, please
specify when ordering.
Precautions
Ensure that all O-ring grooves are not worn or damaged, also that
corrosion is kept in check on O-ring surfaces.
15
HAY PULLEY 7 (HOWCO STYLE)
Part Number
Assembly OIL-HAYP-7000-HC00-W01
HAY PULLEY 12
HAY PULLEY 16
16
LUBRICATORS
Purpose
To accommodate downhole wireline tool strings while rigging up, and during
wireline operations, as well as when entering the wellbore and returning to
surface.
Description
The Lubricator is made of 7 components:
1. Hand Union Female
2. Lubricator Tube
3. Ported Sub
4. Hand Union Male
5. Nut
6. O-Ring
7. O-Ring
The lubricator is made up of sections of tubing material threaded on both
ends to accept hand unions. Once they are made up with hand unions they
are known as lubricator joints, and come in 8 or 10 foot lengths.
Standard lubricator sizes on slickline service units are 2.875 and 3.50 inches
OD (outside diameter). Lubricator sizes are also available up to 7 OD.
Sour service or NACE spec. lubricator joints are machined from Sour service
stock material, where the upper and lower hand unions are machined as part
of the lubricator joint or maybe made with sealed premium thread
connections.
An optional bleed sub may be incorporated into the lubricator assembly. This
involves a ported .50 NPT sub between the lubricator tube and the bottom
hand union.-
17
LUBRICATOR SECTIONS
18
LUBRICATOR SECTIONS
19
PUMP-IN SUB W/ WECO UNION
Part Number
3" ID - 5M w/ 4 3/4"-4 Weco
(screwed inside) OIL-PISB-3000-5MSI-W01
20
QUICK UNION
Type "O"
5" x 4" Assembly OIL-QKUO-5000-4000-W01
COMPONENTS
Pin Section - 2 3/8" EUE Connection
Pin Section - 2 7/8" EUE Connection
Pin Section - 3 1/2" NU Connection
Pin Section - 3 1/2" LP Connection
Threaded Half - 2 3/8" EUE connection
Threaded Half - 2 7/8" EUE Connection
Threaded Half - 3 1/2" NU Connection
Threaded Half - 3 1/2" LP Connection
Nut
Blanking Cap Assembly
O-ring
21
RISER DUAL .5 NPT
Purpose
Gives the ability to either pump into / or bleed off wellbore pressure.
Description
The Riser consists of 3 components:
1. Riser Body
2. Hand Nut
3. Bottom Union
The Riser incorporates two .5 NPT ports to allow the bleed off, or injection
of wellbore gasses or liquids.
Precautions
Ensure threads are not worn or damaged.
Part Number
Assembly OIL-RSDU-5000-NPT0-W01
COMPONENTS
Riser Body
Hand Nut
Bottom Union
22
STUFFING BOX
Purpose
Controls the running of slickline into the lubricator and down the wellbore
and contains any well pressure that may exist.
Description
The sheave wheel is supported with bearings and spindle between two
arms.
The two arms are attached to the staff and held in place at the top with the
wire guide when bolted into place. The staff mounts on top of the main
body with an upper and lower bearing. This assembly is held in place with
the hydraulic packing adapter nut.
The packing and packing glands are contained in the body, all having a hole
in the center for the wire to pass through.
The stuffing box is attached to the top of the lubricator with a hand union.
Part Number
5000 PSI WP Assembly OIL-SFBX-0000-5K00-W01
10,000 PSI WP Assembly OIL-SFBX-0000-10K0-W01
15,000 PSI WP Assembly OIL-SFBX-0000-15K0-W01
(less staff assembly)
COMPONENTS
Body OLG-G-15-901446
Union Nut OLG-G-15-901546
Packing Nut OLG-G-15-901146
Upper Packing Gland OLG-G-15-901046
Lower Packing Gland OLG-G-15-900946
Packing OLG-G-15-435691
Blow Out Plug OLG-G-15-900746
Blow Out Plug Retainer OLG-G-15-900846
Staff Jam Nut OLG-G-15-901246
The tool catcher also comes with a integral velocity check valve, meaning the in the case that the wireline is
parted and travels through the stuffing box / control head, the wellbore is contained through the use of a
one way check
valve.
Description
Designed to be install directly beneath a stuffing box / control head in lubricator string.
Hydraulically controlled so as to be manipulated remotely via a hand pump during wireline operations.
Integral velocity check valve to prevent wellbore gases or fluids from escaping to the atmosphere in the
event that the slickline / wireline is pulled free of the stuffing box / control head during wireline operations.
Purpose
Connects wireline surface equipment to wellhead.
Description
The lower end of the swage connection is either threaded or
flanged to fit the wellhead. The upper end of the swage is
compatible to the bottom hand union of the BOP.
Line Pipe
Part Number
2.00 Assembly OIL-WHSG-2000-LP00-W01
3.00 Assembly OIL-WHSG-3000-LP00-W01
EUE
Part Number
2.375 Assembly OIL-WHSG-2375-EUE0-W01
2.875 Assembly OIL-WHSG-2875-EUE0-W01
3.50 Assembly OIL-WHSG-3500-EUE0-W01
3.875 Assembly OIL-WHSG-3875-EUE0-W01
Please Specify The following When
Ordering this Equipment:
Casing
Union Type
Working Pressure Part Number
4.50 Assembly OIL-WHSG-4500-CSG0-W01
5.50 Assembly OIL-WHSG-5500-CSG0-W01
25
COUNTER HEAD ASSEMBLY
8" (Metric)
.092" OIL-CHAS-082-092M-W01
.105" - .125" OIL-CHAS-105-125M-W01
.187" - .218" OIL-CHAS-187-218M-W01
26
LINE WIPER
Part Number
HOWCO Type Assembly OIL-LNWP-HC00-0000-W01
27
STAFF ASSEMBLY
Part Number
7" Sheave Assembly OIL-STFA-7000-0000-W01
10" Sheave Assembly OIL-STFA-1000-0000-W01
16" Sheave Assembly OIL-STFA-1600-0000-W01
COMPONENTS
Staff
Sheave
Sheave Bearing
Sheave Bolt
Washer
Guard
Staff Bearing
28
SUCKER ROD PIN X BOX CHASER
Part Number
5/8" S.R. Assembly OIL-SRPXB-0625-SR00-W01
3/4" S.R. Assembly OIL-SRPXB-0750-SR00-W01
4 Way Combination OIL-SRPXB-4WY-0000-W01
29
VEEDER ROOT
Part Number
Direct Drive OIL-DTDR-0000-0000-W01
Cable Drive OIL-CBDR-0000-0000-W01
WEIGHT INDICATOR
Part Number
0 - 2000# OIL-WTIN-2000-0000-W01
0 - 4000# OIL-WTIN-4000-0000-W01
0 - 5000# OIL-WTIN-5000-0000-W01
30
COUNTER WHEELS
8" Part Number
.082" (US Measure) OIL-CTWH-8000-082U-W01
.092" (US Measure) OIL-CTWH-8000-092U-W01
.105" (US Measure) OIL-CTWH-8000-105U-W01
.108" (US Measure) OIL-CTWH-8000-108U-W01
.125" (US Measure) OIL-CTWH-8000-125U-W01
.187" (US Measure) OIL-CTWH-8000-187U-W01
.082" (Metric) OIL-CTWH-8000-082M-W01
.092" (Metric) OIL-CTWH-8000-092M-W01
.105" (Metric) OIL-CTWH-8000-105M-W01
.108" (Metric) OIL-CTWH-8000-108M-W01
.187" (Metric) OIL-CTWH-8000-187M-W01
16"
.092" (US Measure) OIL-CTWH-1600-092U-W01
.105" (US Measure) OIL-CTWH-1600-105U-W01
.108" (US Measure) OIL-CTWH-1600-108U-W01
.125" (US Measure) OIL-CTWH-1600-125U-W01
.187" (US Measure) OIL-CTWH-1600-187U-W01
.218" (US Measure) OIL-CTWH-1600-218U-W01
.092" (Metric) OIL-CTWH-1600-092M-W01
.105" (Metric) OIL-CTWH-1600-105M-W01
.108" (Metric) OIL-CTWH-1600-108M-W01
.125" (Metric) OIL-CTWH-1600-125M-W01
.187" (Metric) OIL-CTWH-1600-187M-W01
PRESSURE WHEELS .218" (Metric) OIL-CTWH-1600-218M-W01
MATHEY
.082" OIL-PWMT-0000-082-W01
.092" OIL-PWMT-0000-092-W01
.105" OIL-PWMT-0000-105-W01
.108" OIL-PWMT-0000-108-W01
.125" OIL-PWMT-0000-125-W01
.187" OIL-PWMT-0000-187-W01
31
GIN POLE
PART NUMBER
Assembly OIL-GNPL-0000-0000-W01
32
RELEASING TOOL
Part Number
2" OIL-RLT-2000-0000-W01
2 1/2" OIL-RLT-2500-0000-W01
3" OIL-RLT-3000-0000-W01
4" OIL-RLT-4000-0000-W01
33
PACKING
Part Number
BK Packing OLG-G-17-435191
BK Teflon Ring OLG-G-17-435291
RD Lower Packing OLG-G-17-434891
RD Lower Teflon Ring OLG-G-17-434991
RD Upper Packing OLG-G-17-435391
RD Upper Teflon Ring OLG-G-17-435491
91V38 (2.188" T) OIL-PK91V-3800-2188T-W01
91V64 (2.875" S) OIL-PK91V-6400-2875S-W01
91V172 - Prong Packing OIL-PK91V-1720-PRPK-W01
91V310 (1.781") OIL-PK91V-3100-1781-W01
91V318 (2.313") OIL-PK91V-3180-2313-W01
91V320 (3.813" X) OIL-PK91V-3200-3813X-W01
91V345 (1.250") OIL-PK91V-3450-1250-W01
91V346 (1.625") OIL-PK91V-3460-1625-W01
91V347 (1.500") OIL-PK91V-3470-1500-W01
91V366 (2.750" T) OIL-PK91V-3660-2750-W01
91V1214 (1.710" R) OIL-PK91V-1214-1710R-W01
91V1216 (2.188" R) OIL-PK91V-1216-2188R-W01
91V1330 (2.813" X) OIL-PK91V-1330-2813X-W01
91V3308 OIL-PK91V-3308-0000-W01
91V3306 (2" V-Packing) OIL-PK91V-3306-2VPK-W01
91V3310 (2 1/2" V-Packing) OIL-PK91V-3310-25VP-W01
91V3376 (2.750" X) OIL-PK91V-3376-2750X-W01
91V3380 (2.125" R) OIL-PK91V-3380-2121R-W01
91V3385 (2.562") OIL-PK91V-3385-2562-W01
1.78" Baker OIL-BPK-1780-C000-W01
1.81" Baker OIL-BPK-1810-C000-W01
1.87" Baker OIL-BPK-1870-C000-W01
2.25" Baker OIL-BPK-2250-C000-W01
2.750" Baker OIL-BPK-2750-C000-W01
2.31" Baker OIL-BPK-2310-C000-W01
2.81" Baker OIL-BPK-2810-C000-W01
2.25" Camco OIL-CMPK-2250-C000-W01
1.81" Camco OIL-CMPK-1810-C000-W01
34
PACKING
Part Number
Low Pressure Stuffing Box Packing OIL-LPSBP-0000-C000-W01
35
Oilog, Inc
10370 Richmond Ave. Ste 895.
Houston, TX 77042