Professional Documents
Culture Documents
Programmable Logic 7. Nameplate 14. RUN/STOP switch Additional remark: Refer to the PLC Technique Application Manual for relevant special relays and data registers.
DVP08SN11R 0 8 Relay
Do not touch the internal circuit for at least 1 minute after the power supply is OFF.
Input Point Electric Specifications
Make sure that the PLC is properly grounded , to avoid any electromagnetic noise. Input Type DC (SINK or SOURCE)
DVP08SN11T 0 8 Transistor Input Current 24VDC 5mA
OffOn, above 16VDC
DC Type Motion Level
2 INTRODUCTION 24VDC Sink or Source OnOff, below 14.4VDC
DVP08SP11R 4 4 Relay Responding Time About 10ms (An adjustment range of 0~20ms could be selected through D1020 and D1021)
2.1 Model Explanation and Peripherals
DVP08SP11T 4 4 Transistor Output Point Electric Specifications
Thank you for choosing DELTAs DVP PLC Series. The DVP-SS series provides a 14-point Main Processing Unit
Output Type Relay-R Transistor-T
and allows to expand units with 8~16 points. The maximum input/output points could be extended up to 128 points. DVP16SP11R 8 8 Relay
55 0.1A/1point, 50 0.15A/1point
Current Specifications 1.5A/1 point (5A/COM)
Since the power supply unit is independent of the main unit, and with the volume of the device being smaller, the 45 0.2A/1 point, 40 0.3A/1 point (2A/COM
DVP16SP11T 8 8 Transistor Voltage Specifications Below 250VAC, 30VDC 30VDC
installation of DVP PLC is thus easier.
90 W
Maximum Loading 75 VA (Inductive) 9W
Analog/temperature module extension unit (Resistive)
Nameplate Explanation
Responding Time About 10 ms OffOn 15us OnOff 25us
Please refer to user manuals that go with PLC.
PLC Model
Input Power Supply Specification Power Supply Module
Output Module Specification 4 INSTALLATION & WIRING
Bar Code and Serial Number Input/Output
CE
Software Version V4.9 Model Profile Reference
Input Power Output Power 4.1 Terminal Wiring of the Standard Function MPU and the Digital I/O Extension Unit
Power Module MPU Digital I/O Extension Unit
Model Explanation
100~240VAC Output voltage: 24VDC
Model Serial Number Explanation DVPPS01 DVPPS01 DVPPS02 DVP14SS DVP08SM DVP08SN DVP08SP DVP16SP
( 50/60Hz ) Output current (max.): 1A
S
/X
S01234567 001122345
S
/X
S01234567
S
/
S0123
S
/
S01234567 001234567
0Y
C0Y
XXXX
XXXXXXXX CYYYYYYYY
XXXXXXX CYCYCYYYY
XXXXXXX
1Y
Version
2Y
Product Series
3Y
R: Relay DVP-PS01 DVP-PS02
4Y
Input+Output point Production Week 100~240VAC Output voltage: 24VDC
T: Transistor
5Y
DVPPS02
( 50/60Hz ) Output current (max.): 2A
6Y
Production Year (2002)
RUN
7
Production Place (Taoyuan)
0Y
C
Model type
0C
DC Power Input
STOP
Version
1Y
S: Standard Function MPU
1C
Production Model
2Y
M: Input Point Expansion Unit
2C
N: Output Point Expansion Unit 3 STANDARD SPECIFICATIONS
3Y
3
P: I/O Point Expansion Unit
enclosure with sufficient space (as shown diagram on the right) to its
DVPACAB315 Cable (HPP PC, 1.5m) Program Capacity 3792 Steps Built-in EEPROM
surroundings for heat dissipation purpose. 50mm DVP MPU 50mm
a depth of 7.5mm, and when mounting the PLC on the DIN rail, be sure to use the end bracket to stop any
RUN
X0
ERROR
14
X1
8
T64~T126 (10 ms time base, when M1028 is
X3
RUN
X5
X6
10 12
On) of the PLC is a small retaining clip. To secure the PLC to the DIN rail, place it onto the rail and gently
push up the clip. To remove it, pull down the retaining clip and gently pull the PLC away from the DIN rail.
X7
C0
9
General 112 Points C0~C111
Y0
90.00 13
Wiring
C1
Y1
2
C2
Counter Latched 16 Points C112~C127
Y2
3 22-16AWG Use the 22-16AWG (1.5mm) single-core bare wire or the multi-core wire for the
High-Speed 13 Points 1-Phase 20KHz, 2-Phase 5KHz C235~C254 (all of which are latched type)
Y3
I/O wiring, and the specifications of the terminal are shown diagram on the left.
Y4
Y5