Professional Documents
Culture Documents
Audio Power
Audio power
amplifiers
Section Page
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
2 Product survey and page reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
In application sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
In power output sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
3 Audio amplifier ICs for portable radio/audio equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
4 Audio amplifier ICs for car radios/power boosters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
5 Audio amplifier ICs for mains-powered systems including hi-fi and TV sound . . . . . . . . . . . . . . . . 5-1
Appendices
1 Further information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
Application notes and leaflet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
2 Index of audio amplifier ICs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3
NOTE
Purchase of Philips I2C components
conveys a license under the Philips I2C
patent to use the components in the I2C
system, provided the system conforms to
the I2C specifications defined by Philips.
Integrated power The publication is divided into three application areas: portable
A major feature of our latest range is the high degree of func- radio/audio, car radio and mains-powered systems. Many prod-
tional power integrated within each package. A functional power ucts, however, may be suitable for several application areas: car
that dramatically reduces the peripheral component count of audio systems and mains-powered multimedia PCs for example.
finished equipment, leading to: Whats more, many of todays applications for audio amplifier
lower system development costs ICs, e.g. musical greeting cards, were unheard of just a few years
smaller, more compact circuitry ago. This means that any subdivision such as that given in this
far fewer production problems guide can be only a preliminary indication of a products suit-
significantly lower production costs. ability for a particular application. In using this guide, therefore,
designers should cast their net as wide as possible and should
consider all likely candidates when looking for a suitable audio
IC for their application.
PRODUCT SURVEY
Type No. RMS power (W) Supply (V) Package Remarks Page
TDA1011 6.5 3.6 to 24 SIL9MP Separate pre/power amplifiers 3-2
TDA1015 4 3.6 to 18 SIL9MP Separate pre/power amplifiers 3-2
2 TDA1015T 0.5 3.6 to 12 SO8 Separate pre/power amplifiers 3-2
TDA1016 2 3.6 to 15 DIP16 Record/playback + ALC 3-3
TDA1308T 2 0.06 (d = 0.1%) 3 to 7 SO8 Stereo headphone driver 3-4
TDA7050(T) [0.15]/2 0.075 1.6 to 6 DIP8, SO8 No peripheral components 3-5
TDA7052/ 1 3 to 18 DIP8 No peripheral components 3-6
TDA7053 21 No peripheral components
TDA7052A(AT)/ 1(0.5) 4.5 to 18 DIP8, SO8 DC volume control; 36 dB gain 3-7
TDA7052B(BT) TDA7052A(AT) with 40 dB gain
TDA7053A(AT) 2 1(2 0.5) 4.5 to 18 DIP16, SO16 DC volume control; 40 dB gain 3-8
TDA7056/ 3 3 to 18 SIL9MP No peripheral components 3-9
TDA7057Q 23 SIL13P No peripheral components
TDA7056A/ 5 4.5 to 18 SIL9MP DC volume control; 36 dB gain 3-10
TDA7056B TDA7056A with 40 dB gain
TDA7057AQ 25 4.5 to 18 SIL13P DC volume control; 40 dB gain 3-11
TDA8541(T) 1 2.2 to 18 DIP8, SO8 Few peripheral components 3-12
TDA8542(T) 21 2.2 to 18 DIP16, SO16L Few peripheral components 3-13
TDA8543(T) 2 2.2 to 18 DIP16, SO16 Few peripheral components 3-14
TDA8547(T) 21 2.2 to 18 DIP16, SO16L Standby per channel 3-15
TDA8551(T) 1 2.7 to 6 DIP8, SO8 Digital volume control 3-16
TDA8558(T) 0.125 1.8 to 18 DIP8, SO8 Power saving muting facility 3-17
TDA8559(T) 0.035 1.8 to 30 DIP16, SO16 Stereo headphone amplifier 3-18
Note to tables: Output powers are quoted at dtot = 10% unless stated otherwise and depend on supply voltage and loudspeaker
impedance. Figures in square brackets refer to performance in BTL configuration.
Type No. RMS power (W) Supply (V) Package Remarks Page
TDA1010A/ 3.4 to 12 6 to 24 SIL9MP Separate pre/power amplifiers 4-2
TDA1020 + load dump prot., standby, HF limit
TDA1510AQ/ 2 12[1 24] 6 to 18 SIL13P 1-end/BTL, 26 - 50[32 - 56] dB gain 4-3 2
TDA1515BQ TDA1510AQ with LS protection
TDA1516BQ/ 2 12[1 24] 8.5 to 18 SIL13P 2 1-end/1 BTL, 20[26] dB gain 4-4
TDA1516CQ/ TDA1516BQ but BTL only
TDA1518BQ TDA1516BQ with 40[46] dB gain
TDA1517(P)/ 26 8.5 to 18 SIL9MP, DIP18 20 dB gain 4-5
TDA1519 TDA1517 with 40 dB gain
TDA1519A/ 2 11[1 22] 8.5 to 17.5 SIL9P 2 1-end/1 BTL, 40[46] dB gain 4-6
TDA1519B 2 6[1 12] 8.5 to 18 SIL9MP
TDA1552Q/ [2 22] 8.5 to 18 SIL13P Dual BTL amplifiers, [26] dB gain 4-7
TDA1553Q/ TDA1552Q with LS protection
TDA1553CQ/ TDA1553Q with CMOS mode switch
TDA1557Q TDA1553Q with [46] dB gain
TDA1554Q/ 4 11[2 22] 8.5 to 18 SIL17P 1-end/BTL, 20[26] dB gain 4-8
TDA1555Q/ TDA1554Q with distortion detector
TDA1558Q TDA1554Q with 40[46] dB gain
TDA1556Q [2 22] 8.5 to 18 SIL17P Dual BTL, diff. inputs, [26] dB gain 4-9
TDA1560Q [40] 8 to 18 SIL17P BTL class-H amplifier, [30] dB gain 4-10
TDA1561Q 2 23 6 to 18 DBS13P Automatic switching to high-power 4-11
mode when needed
TDA8560Q/ [2 40] 8.5 to 18 SIL13P Dual BTL amplifiers. [40] dB gain 4-12
TDA8563Q/ TDA8560Q with [26] dB gain
TDA8563AQ TDA8563Q with 2.2% THD
(10% with TDA8563Q)
TDA8561Q/ 4 12[2 24] 8.5 to 18 SIL17P 4 1-end/dual BTL, 20[26] dB gain 4-13
TDA8564Q TDA8561Q with 40[46] dB gain
TDA8562Q/ 4 12 8.5 to 18 SIL17P 4 1-end amplifier, 20 dB gain 4-14
TDA8565Q TDA8562Q with 40 dB gain
TDA8566Q 2 25 8.5 to 18 DBS17P Differential inputs 4-15
TDA8567Q/ 4 25 8.5 to 18 DBS23P Quad BTL amplifier, 4 load, [26] dB gain 4-16
TDA8568Q/ TDA8567Q with [40] dB gain
TDA8569Q TDA8567Q driving 2 load
TDA8574(T) dual line driver 6 to 12 DIP16, SO16 Class H high output level 4-17
TDA8576T dual line driver 6 to 12 SO16 Class H high output level 4-18
TDA8577/ dual line driver 5 to 18 SIL9MP Completely separated inputs 4-19
TDA8578(T)/ DIP16, SO16 Completely separated inputs
TDA8579(T) DIP8, SO8 Inverting inputs linked
Note to tables: Output powers are quoted at dtot = 10% unless stated otherwise and depend on supply voltage and loudspeaker
impedance. Figures in square brackets refer to performance in BTL configuration.
Type No. RMS power (W) Supply (V) Package Remarks Page
TDA1013B 4 to 10 10 to 40 SIL9MP DC volume control 5-2
TDA1514A 50 (d = 0.1%) 15 to 60 SIL9P Super hi-fi, 20 - 46 dB gain 5-3/4
2 TDA1521A/ 2 6 (d = 0.5%) 15 to 42 SIL9MP Automatic mute; hi-fi 5-5
TDA2615 TDA1521A with extra mute pin
TDA1521(Q)/ 2 12 (d = 0.5%) 15 to 42 SIL9P Automatic mute; hi-fi 5-5
TDA2616(Q) TDA1521(Q) with extra mute pin
TDA2611A 4 to 10 6 to 35 SIL9MP Adjustable input impedance 5-6
TDA2613/ 6 (d = 0.5%) 15 to 42 SIL9MP Automatic mute; hi-fi 5-6
TDA2614 TDA2613 with extra mute pin
Note to tables: Output powers are quoted at dtot = 10% unless stated otherwise and depend on supply voltage and loudspeaker
impedance. Figures in square brackets refer to performance in BTL configuration.
Type No. RMS power (W) Supply (V) Package Remarks Application Page
TDA8574(T) dual line driver 6 to 12 DIP16, SO16 Class H high output level c, m 4-17
TDA8576T dual line driver 6 to 12 SO16 Class H high output level c, m 4-18
TDA8577 dual line driver 5 to 18 SIL9MP Completely separated inputs c, m 4-19 2
TDA8578(T) dual line driver 5 to 18 DIP16, SO16 Completely separated inputs c, m 4-19
TDA8579(T) dual line driver 5 to 18 DIP8, SO8 Inverting inputs linked c, m 4-19
TDA8559(T) 0.035 1.8 to 30 DIP16, SO16 Stereo headphone amplifier p 3-18
TDA1308T 2 0.06 (d = 0.1%) 3 to 7 SO8 Stereo headphone driver p, c, m 3-4
TDA7050(T) [0.15]/2 0.075 1.6 to 6 DIP8, SO8 No peripheral components p 3-5
TDA1015T 0.5 3.6 to 12 SO8 Separate pre/power amplifiers p 3-2
Low power (1 W to 5 W)
Type No. RMS power (W) Supply (V) Package Remarks Application Page
TDA8558(T) 0.125 1.8 to 18 DIP8, SO8 Power saving muting facility p, m 3-17
TDA7052A(AT)/ 1(0.5) 4.5 to 18 DIP8, SO8 DC volume control; 36 dB gain p, m 3-7
TDA7052B(BT) TDA7052A(AT) with 40 dB gain
TDA7052/ 1 3 to 18 DIP8 No peripheral components p, m 3-6
TDA7053 21 DIP16 No peripheral components
TDA8541(T) 1 2.2 to 18 DIP8, SO8 Few peripheral components p, m 3-12
TDA8551(T) 1 2.7 to 6 DIP8, SO8 Digital volume control p, m 3-16
TDA8542(T) 21 2.2 to 18 DIP16, SO16L Few peripheral components p, m 3-13
TDA7053A(AT) 2 1(2 0.5) 4.5 to 18 DIP16, SO16 DC volume control; 40 dB gain p, m 3-8
TDA8543(T) 2 2.2 to 18 DIP16, SO16 Few peripheral components p, m 3-14
TDA8547(T) 21 2.2 to 18 DIP16, SO16L Standby per channel p, m 3-15
TDA1016 2 3.6 to 15 DIP16 Record/playback + ALC p, m 3-3
TDA7056/ 3 3 to 18 SIL9MP No peripheral components p, m 3-9
TDA7057Q 23 SIL13P No peripheral components
TDA1015 4 3.6 to 18 SIL9MP Separate pre/power amplifiers p, m 3-2
TDA7057AQ 25 4.5 to 18 SIL13P DC volume control; 40 dB gain p, m 3-11
TDA7056A/ 5 4.5 to 18 SIL9MP DC volume control; 36 dB gain p, m 3-10
TDA7056B TDA7056A with 40 dB gain
Note to tables: Output powers are quoted at dtot = 10% unless stated otherwise and depend on supply voltage and loudspeaker
impedance. Figures in square brackets refer to performance in BTL configuration. Application areas: c = car radios/power boosters,
m = mains-powered equipment, p = portable radio/audio equipment.
Medium power (6 W to 12 W)
Type No. RMS power (W) Supply (V) Package Remarks Application Page
TDA1010A/ 3.4 to 12 6 to 24 SIL9MP Separate pre/power amplifiers c, m 4-2
TDA1020 + load dump prot., standby, HF limit
2 TDA1013B 4 to 10 10 to 40 SIL9MP DC volume control m 5-2
TDA2611A 4 to 10 6 to 35 SIL9MP Adjustable input impedance m 5-6
TDA2613/ 6 (d = 0.5%) 15 to 42 SIL9MP Automatic mute; hi-fi m 5-6
TDA2614 TDA2613 with extra mute pin
TDA1011 6.5 3.6 to 24 SIL9MP Separate pre/power amplifiers p, m 3-2
TDA1517(P)/ 26 6 to 18 SIL9MP, DIP18 20 dB gain c, m 4-5
TDA1519 TDA1517 with 40 dB gain
TDA1521A/ 2 6 (d = 0.5%) 15 to 42 SIL9MP Automatic mute; hi-fi m 5-5
TDA2615 TDA1521A with extra mute pin
TDA1521(Q)/ 2 12 (d = 0.5%) 15 to 42 SIL9P Automatic mute; hi-fi m 5-5
TDA2616(Q) TDA1521(Q) with extra mute pin
Type No. RMS power (W) Supply (V) Package Remarks Application Page
TDA1519A/ 2 11[1 22] 8.5 to 17.5 SIL9P 2 1-end/1 BTL, 40[46] dB gain c, m 4-6
TDA1519B 2 6[1 12] 8.5 to 18 SIL9MP
TDA1554Q/ 4 11[2 22] 8.5 to 18 SIL17P 1-end/BTL, 20[26] dB gain c 4-8
TDA1555Q/ TDA1554Q with distortion detector
TDA1558Q TDA1554Q with 40[46] dB gain
TDA1510AQ/ 2 12[1 24] 8.5 to 18 SIL13P 1-end/BTL, 26 - 50[32 - 56] dB gain c 4-3
TDA1515BQ TDA1510AQ with LS protection
TDA1516BQ/ 2 12[1 24] 8.5 to 18 SIL13P 2 1-end/1 BTL, 20[26] dB gain c 4-4
TDA1516CQ/ TDA1516BQ but BTL only
TDA1518BQ TDA1516BQ with 40[46] dB gain
TDA8562Q/ 4 12 8.5 to 18 SIL17P 4 1-end amplifier, 20 dB gain c 4-14
TDA8565Q TDA8562Q with 40 dB gain
TDA8561Q/ 4 12[2 24] 8.5 to 18 SIL17P 4 1-end/dual BTL, 20[26] dB gain c 4-13
TDA8564Q TDA8561Q with 40[46] dB gain
TDA1552Q/ [2 22] 8.5 to 18 SIL13P Dual BTL amplifiers, [26] dB gain c 4-7
TDA1553Q/ TDA1552Q with LS protection
TDA1553CQ/ TDA1553Q with CMOS mode switch
TDA1557Q TDA1553Q with [46] dB gain
TDA1556Q [2 22] 8.5 to 18 SIL17P Dual BTL, diff. inputs, [26] dB gain c 4-9
TDA1561Q 2 23 6 to 18 DBS13P Automatic switching to high- c, m 4-11
power mode
TDA8566Q 2 25 8.5 to 18 DBS17P Diagnostic outputs c 4-15
TDA8567Q/ 4 25 8.5 to 18 DBS23P Quad BTL amplifier, 4 load,
[26] dB gain c 4-16
TDA8568Q/ TDA8567Q with [40] dB gain c 4-16
TDA8569Q TDA8567Q driving 2 loads c 4-16
TDA1560Q [40] 8 to 18 SIL17P BTL class-H amplifier, [30] dB gain c, m 4-10
TDA8560Q/ [2 40] 8.5 to 18 SIL13P Dual BTL amplifiers. [40] dB gain c 4-12
TDA8563Q/ TDA8560Q with [26] dB gain
TDA8563AQ TDA8563Q with 2.2% THD
TDA1514A 50 (d = 0.1%) 15 to 60 SIL9P Super hi-fi, 20 - 46 dB gain m 5-3/4
Note to tables: Output powers are quoted at dtot = 10% unless stated otherwise and depend on supply voltage and loudspeaker
impedance. Figures in square brackets refer to performance in BTL configuration. Application areas: c = car radios/power boosters,
m = mains-powered equipment, p = portable radio/audio equipment.
PORTABLE RADIO/
AUDIO EQUIPMENT
220 nF
No switch-on/switch-off clicks 5 3
4
Output noise diminishes with reducing volume TDA1011/
1 F TDA1015 100 F
2 2
input PREAMP. POWER
AMP. 680
These ICs are primarily for battery-powered portable recorders F
100
and radios, the TDA1011 offering an output power of 6.5 W 9 7 6 1
nF
TDA1015T
0.1 F 220 F
1 4
input PREAMP. POWER
This amplifier is for portable and mains-powered equipment. It AMP.
TDA1016
stand-by switch
2.2 M VP
10 k 100
22 F 220 nF nF
47
22 F
82 k F
180 5 7 6 4 3
10 k
k 2
ALC
record-
input R 1 F
8 STAB 100 F
470 F
P POWER 1
2.2 270 PREAMP.
9
TDA1016 AMP.
nF k 100
playback nF
input 4
11 10 12 13 14 15 16 2.7
22 220 pF
100 k F
1 F 10 nF
22 F
22 nF 160 MSB421
68 k 560 pF
10 k 100 k
P
3.3 k 470 pF
R
22 k
4.7 k
24 k 5.1 k 82 k
56
220 pF
10 nF
TDA1308T
VP
1 nF 100 F
10 k
1 8
2
input 1
3
1 nF
10 k
TDA7050(T)
150 mW BTL or 2 75 mW
low-voltage amplifier
VP
100 nF
VP
8 100
left channel 8
input nF
input
2 1
22 k 7 22 k 7
1
2
47 F
TDA7050(T)
right channel TDA7050(T)
input
3
22 k 6 4
4 6
47 F 3
5
MSB405 MSA612
TDA7052/TDA7053
VP
100 220
5 nF F
TDA7053
VP
input 1 16
100 220
1 nF F
2
TDA7052 5 k
1
input 5
13
signal
2 ground 1
5 k
3
8
signal input 2 12
ground
6
6 5 k
MSB420
7
power ground
9
signal
ground 2
10 14 MSA611
power ground 1 power ground 2
TDA7052A(AT)/TDA7052B(BT)
No external components required portable recorders, radios and telephones, their wide supply volt-
Excellent overall stability age range (4.5 V to 18 V) also makes them suitable for multi-
media and TV applications.
Output protected against short-circuit to Vp,
ground or across load The amplifiers have built-in DC volume control with a logarith-
No external heatsink required mic characteristic providing control over a typical range of 3
Low power consumption 80 dB (73 dB B versions). When the DC control voltage drops
below 0.3 V (0.4 V B versions), the amplifier is muted. Except
Thermal protection
for pin 4 (DC volume control), the amplifiers are pin-compati-
Low HF radiation ble with the TDA7052.
All pins ESD protected
No switch-on/switch-off clicks They come in an 8-pin plastic DIP (TDA7052A/7052B) or in
an 8-pin small outline (SO) plastic package for surface mount-
Supply voltage range of 4.5 V to 18 V
ing (TDA7052AT/TDA7052BT).
DC volume control
Mute facility
VP
100 nF 220 F
1
7
n.c.
TDA7052A/B
TDA7052AT/BT 5
0.47 F
input 2
STABILIZER TEMPERATURE
Vref PROTECTION
DC
volume
control 3 6
MBC281
ground
TDA7053A/TDA7053AT
No external components required marily for battery-powered portable recorders, radios and tele-
Excellent overall stability phones, their wide supply voltage range (4.5 V to 18 V) also
makes them suitable for multimedia and TV applications.
Output protected against short-circuit to Vp,
ground or across load The amplifiers have built-in DC volume control with a logarith-
3 No external heatsink required mic characteristic providing control over a typical range of
Low power consumption. 73 dB. When the DC control voltage drops below 0.4 V, the
amplifier is muted.
Thermal protection
Low HF radiation They come in a 16-pin plastic DIP (TDA7053A) or in a 16-pin
All pins ESD protected small outline (SO) plastic package for surface mounting
No switch-on/switch-off clicks (TDA7053AT).
Supply voltage range of 4.5 V to 18 V
DC volume control
Mute facility
POWER OUTPUT AT d tot = 10%
These amplifiers are stereo versions of the TDA7052B/ power supply load
TDA7052BT. They use the same proprietary circuit design output voltage impedance
which makes use of the bridge-tied load (BTL) principle to pro- (W) (V) ()
vide low-voltage operation without sacrifice of output power. TDA7053A
They have fixed voltage gain of 40 dB. Although they are pri- 21 6 8
22 12 32
TDA7053AT
2 0.5 6 16
VP
100 nF 220 F
5
TDA7053A
0.47 F TDA7053AT
4 16
input 1
DC 2
volume
control 1
13
TEMPERATURE
Vref STABILIZER PROTECTION
0.47 F
6 12
input 2
DC 8
volume
control 2
9
7 14 10 MSA718 - 2
ground
TDA7056/TDA7057Q
TDA7057Q
23 11 16
VP
100 220
3 nF F
TDA7057Q
VP input 1 13
100 220
2 nF F 2
5 k
TDA7056 1
input 6 11
signal
ground 1
3
5 k
4
input 2 10
8
signal
ground 4
5 k
7 5
MSB419
power ground 8
signal
ground 2
9 12 MSB418
power ground 1 power ground 2
TDA7056A/TDA7056B
VP
100 nF 220 F
2
1
n.c.
9 TDA7056A
n.c. TDA7056B 6
0.47 F
input 3
STABILIZER TEMPERATURE
Vref PROTECTION
DC
volume
control 4 7
MBC280
ground
TDA7057AQ
No external components required The amplifier has built-in DC volume control with a logarith-
Excellent overall stability mic characteristic providing control over a typical range of
73 dB. When the DC control voltage drops below 0.4 V, the
Output protected against short-circuit to Vp,
amplifier is muted.
ground or across load
Low power consumption The IC comes in a 13-pin plastic SIL package with the leads 3
No switch-on/switch-off clicks bent to DIL format.
DC volume control
Mute mode
Thermal protection
Low HF radiation
All pins ESD protected
(1)
VP
100 nF 220 F
4
TDA7057AQ
0.47 F
3 13
input 1
DC 1
volume
control 1
11
TEMPERATURE
V ref STABILIZER PROTECTION
0.47 F
5 10
input 2
DC 7
volume
control 2
8
not 2
connected
6 12 9
MSA715 - 1 ground
TDA8541/TDA8541T
1 W BTL amplifiers
TDA8541
4 5
IN OUT
3
IN+ +
R
6
VCC R
20 k 8
OUT+
2
+
SVR
20 k
1
MODE STANDBY/MUTE LOGIC
7
GND
MGB972
TDA8542/TDA8542T
2 1 W BTL amplifiers
Few external components required These amplifiers are stereo versions of the TDA8541/
Low saturation voltage of output stage TDA8541T. They are primarily for battery-powered applica-
tions such as portable recorders and radios and cellular tele-
Gain settable with external resistors
phones. However, their wide supply voltage range (2.2 V to
Standby mode controllable by CMOS-compatible 18 V) also makes them suitable for mains powered applications
levels such as multimedia PCs. The amplifiers also feature a standby/
Low standby current mute facility to avoid switch-on/switch-off clicks. 3
No switch-on/switch-off clicks
Besides audio applications, they are also suitable for use as elec-
High supply-voltage ripple rejection tric motor drivers in, for example, CD servo systems.
Thermal protection
Outputs short-circuit safe to ground, VCC and The amplifiers come in a 16-pin plastic DIP (TDA8542) or in a
16-pin small outline (SO) plastic package for surface mounting
across load
(TDA8542T).
All pins ESD protected
POWER OUTPUT AT d tot = 10%
power supply load
output voltage impedance
(W) (V) ()
21 5 8
VCCL VCCR
16 9
14 15
INL OUTL
13
INL+ +
R
VCCL
R
2
20 k OUTL+
+
20 k
STANDBY/MUTE LOGIC
TDA8542
11 10
INR OUTR
12
INR+ +
R
VCCR
R
7
20 k OUTR+
4 +
SVR
20 k
3
MODE
5 STANDBY/MUTE LOGIC
BTL/SE
1 8
MGB975
LGND RGND
TDA8543/TDA8543T
2 W BTL amplifiers
VCC
12
6
IN 11
5 OUT
IN+
VCC R
20 k
14
OUT+
4
SVR
20 k
TDA8543
3 STANDBY/MUTE
MODE
LOGIC
13 MSC249
GND
TDA8547/TDA8547T
Independent standby selection of output channels These BTL stereo amplifiers incorporate standby/mute logic that
Few external components required allows either one of the output channels to be switched into a
standby condition. This feature can be used, for example, for
Low saturation voltage of output stage
loudspeaker selection. The amplifiers are primarily for battery-
Gain settable with external resistors powered applications such as portable recorders and radios and
Standby mode controllable by CMOS-compatible cellular telephones. However, their wide supply voltage range 3
levels (2.2 V to 18 V) also makes them suitable for mains powered
applications such as multimedia PCs.
Low standby current
No switch-on/switch-off clicks The amplifiers come in a 16-pin plastic DIP (TDA8547) or in a
High supply-voltage ripple rejection 16-pin small outline (SO) plastic package for surface mounting
Thermal protection (TDA8547T).
Outputs short-circuit safe to ground, VCC and
across load
All pins ESD protected
POWER OUTPUT AT d tot = 10%
power supply load
output voltage impedance
(W) (V) ()
21 5 8
VCC1 VCC2
16 9
14
IN1 15
13 OUT1
IN1+
R
R
2
OUT1+
STANDBY/MUTE
LOGIC
11
IN2 10
12 OUT2
IN2+
VCC R
20 k
7
OUT2+
4
SVR
20 k
TDA8547
3
MODE STANDBY/MUTE
5
SELECT LOGIC
8 1 MSC261
GND2 GND1
TDA8551/TDA8551T
up/down VCC
1 6
MASTER
4 VOLUME
in 8
CONTROL OUT+
VCC
20 k
50 k
5 k R
3
SVT
R
50 k
5
TDA8551 OUT+
SLAVE
STANDBY/MUTE
OPER
2 7 MSC262
MODE GND
TDA8558/TDA8558T
VP
8
1 VP
STANDBY REF
4 INPUT
MUTE 7
LOGIC OA OUT+
2
INPUT OA DQC
3
VP
5
OA OUT
TDA8558
8 MSC263
GND
TDA8559/TDA8559T
Operating voltages down to 1.9 V battery-powered applications (2 1.5 V cells) in, for example,
Very low quiescent current personal audio equipment. They can also be used as a mono
amplifier (e.g. in cellular phones) and as a line driver in mains-
Low distortion
powered applications without need of any external components.
Few external components required A dynamic quiescent controller (DQC) feature automatically
Differential inputs increases quiescent current at higher frequencies to minimize
3 Can be used as a mono amplifier in BTL or stereo HF cross-over distortion. The amplifiers also feature a standby/
mute facility to avoid switch-on/switch-off clicks.
single-ended (SE) mode
SE mode without need of capacitor in series with They come in a 16-pin plastic DIP (TDA8559) or in a 16-pin
the loudspeaker small outline (SO) plastic package for surface mounting
Mute and standby mode (TDA8559T).
No switch-on/switch-off clicks
Outputs short-circuit safe to ground, VCC and
across load POWER OUTPUT AT d tot = 10%
All pins ESD protected power supply load
output voltage impedance
These BTL stereo amplifiers operate at voltages from as low as (W) (V) ()
1.9 V up to a maximum of 30 V and they consume very little 0.035 3 32
quiescent current. The amplifiers are therefore ideally suited to
BTL mode
0.140 3 25
VP2 VP1
15 16
1
STANDBY REFERENCE
VP
2 +
INV1
V/I
3 14
INV1 OA OUT1
+
50 k 50 k
DQC
7
MUTE
INPUT
8 DQC
MODE LOGIC
+
5 11
INV2 + OA OUT2
V/I
6
INV2
50 50
k k
VP
4 12
SVRR BUFFER BUFFER
TDA8559
9,10 13
MGD115
n.c. GND
CAR RADIOS/
POWER BOOSTERS
TDA1010A/TDA1020
stand-by
680 F
100 nF switch 100 nF
VP
330 k
5 3 100 F
4
TDA1010A
1 F
8 2
input PREAMP. POWER
AMP. 1000 F
100
nF
9 7 6 1
RL
100 nF
4.7
1 nF
MSB412
TDA1510AQ/TDA1515BQ
24 W BTL or 2 12 W amplifiers
Low offset voltage at output (<50 mV) important These class-B output amplifiers can be used in car audio systems
for BTL to drive loads down to 1.6 . They have externally adjustable
voltage gain.
Externally adjustable voltage gain range of 32 dB
to 56 dB in BTL configuration and 26 dB to 50 dB They come in 13-pin plastic SIL power packages with the pins
in stereo configuration (14.4 V supply, 4 load) bent to DIL format.
High ripple rejection (50 dB at 1 kHz, Rs = 0 )
Load dump and SOAR protection
Protection against AC short-circuit from output to
ground
Thermal protection
4
Internally limited bandwidth for rejection of HF
interference
Low standby current (<2 mA) to simplify switching
Few external components needed
100 k 100 k
100 F
stand-by switch
100 k 100 k
VP 47 F
22 stand-by switch
0.1
F VP
3 11 10 22 0.1
0.1 F F
2 3 11 10
TDA1510AQ 12
input
TDA1515BQ 0.22 F
0.1 F input
2 TDA1510AQ 12
1 13 TDA1515BQ
0.22 F
1 13
6 5 9 8 7
4 6 5 9 8 7
100 F 100 F
(1) 330 pF
100 k 100 k
47 F
1 1 680
mF mF 0.1 100 F 100 F
0.1 F
1 k F 1 k
4.7 0.1 F
4.7 4.7 100 k 100 k
4.7 F 4.7 F
MSB410
MSB411 2 k
(1)
TDA1515B only 4.7 F
TDA1516BQ/TDA1516CQ/TDA1518BQ
24 W BTL or 2 12 W amplifiers
8 8
to VP to VP
60 k 9 9
60 k
220 nF
13 input 2 13 1 mF
3 7 3 7
MSB259
TDA1517(P)/TDA1519
2 6 W amplifiers
Fixed closed-loop voltage gain of typically 20 dB for The TDA1517 and TDA1519 are stereo power amplifiers devel-
the TDA1517(P), 40 dB for the TDA1519 (14.4 V oped for use in car audio systems. They are virtually identical
except for their gain.
supply, 4 load)
Excellent channel balance (within 1 dB) The TDA1517 and TDA1519 come in 9-pin plastic SIL
High supply voltage ripple rejection (48 dB medium-power packages and the TDA1517P comes in an
between 100 Hz and 10 kHz, Rs = 0 ) 18-pin DIP.
Load dump protection
Output protected against AC and DC short-circuit
to ground or supply
Thermal and SOAR protection
4
Reverse polarity safe
Protected against electrostatic discharge
Few external components needed
Standby feature with switch-on voltage of 0 V to
2 V at pin 8 and a switch-on current of only 12 A
to allow use of an inexpensive switch. The standby
supply current is <100 A. The voltage at pin 8 for
normal operation is >8.5 V
Mute facility with switch-on voltage of 3 V to 6.4 V
POWER OUTPUT AT d tot = 10%
at pin 8 to eliminate switch-on/switch-off clicks.
power supply load
The supply current in the muted condition is output voltage impedance
40 mA (W) (V) ()
26 14.4 4
stand-by switch
VP
100
100 nF
F
2200
F
input
reference internal
voltage 1/2 V P
TDA1517
60 k 60 k
220 nF 220 nF
input 1 input 2
MSB261 - 1
1000 F 1000 F
TDA1519A/TDA1519B
No external components in BTL configuration Mute facility with switch-on voltage of 3.3 V to
Very few external components in stereo 6.4 V at pin 8 to eliminate switch-on/switch-off
configuration clicks. The supply current in the muted condition
Low offset voltage at output (250 mV) important is 40 mA
for BTL Identical inputs (inverting and non-inverting)
Fixed closed-loop voltage gain (14.4 V supply, 4
load) of 46 dB for BTL and 40 dB for stereo These are car audio class-B power amplifiers with internally
High supply voltage ripple rejection (48 dB fixed gain for excellent channel balance (within 1 dB). The two
4 between 100 Hz and 10 kHz, Rs = 0 )
types are virtually identical except for their output power.
Load dump protection The TDA1519A comes in a 9-pin power plastic SIL package
Output protected against AC and DC short-circuit with or without the pins bent to DIL format. The TDA1519B
to ground or supply rail comes in a 9-pin plastic medium-power SIL package.
Thermal protection
Reverse polarity safe
POWER OUTPUT AT d tot = 10%
Standby feature with switch-on voltage of 0 V to
power supply load
2 V at pin 8 and a switch-on current of only 12 A
output voltage impedance
to allow use of an inexpensive switch. The standby (W) (V) ()
supply current is <100 A. The voltage at pin 8 for mono BTL (TDA1519A/1519B)
normal operation is >8.5 V 22/12 14.4 4
stereo (TDA1519A/1519B)
2 11/6 14.4 4
220 nF 220 nF
1 input 1
1
input 4 4
60 k 60 k
internal internal
Vref. V ref. 1 mF
60 k 60 k
6 220 nF 6
9 9
input 2
TDA1519A(B) TDA1519A(B)
1/2 VP 1/2 VP
3 2 5 3 2 5
MSB260
TDA1552Q/TDA1553Q/CQ/TDA1557Q
2 22 W BTL amplifiers
mute/stand-by mute/stand-by
not connected VP VP
100 nF 100 nF
2.2 2.2
12 11 3 10 mF 12 11 3 10 mF
TDA1552Q/TDA1557Q TDA1553Q(CQ)
220 nF 220 nF
input 1 1 input 1 1
4 4
60 k 60 k
6 6
220 nF 220 nF
input 2 13 input 2 13
9 9
60 k 60 k
7 7
* connected to Vref on
the TDA1557Q 5 8 5 8 MSB257
TDA1554Q/TDA1555Q/TDA1558Q
2 22 W BTL or 4 11 W amplifiers
TDA1554Q/1555Q/1558Q TDA1554Q/1555Q/1558Q
220 nF 220 nF
1 1 1 mF
input 1 6 input 1 6
60 k 60 k
60 k 60 k 1 mF
8 220 nF 8
2 2
input 2
60 k 1 mF
10 220 nF 60 k 10
16 16
input 4
* not connected
3 7 11 9 on the TDA1554Q 3 7 11 9
connected to Vref
signal ground signal ground
not connected on the TDA1558Q not connected
MSB255
power ground (substrate) power ground (substrate)
TDA1556Q
Very few external components This is a class-B power amplifier with internally fixed gain for
Differential inputs excellent channel balance (within 1 dB). The amplifier has two
differential input stages with high Common Mode Ripple
High CMRR (>64 dB)
Rejection (CMRR) which makes it very attractive for car radio
High supply voltage ripple rejection (48 dB booster applications. The TDA1556Q also incorporates a
between 100 Hz and 10 kHz, Rs = 0 ) Dynamic Distortion Detector (DDD) and loudspeaker protec-
Low offset voltage at output (150 mV) important tion.
for BTL
It comes in a 17-pin plastic SIL power package with the pins
Fixed closed-loop voltage gain (14.4 V supply, 4 bent to DIL format.
load) of 26 dB 4
Load dump protection
Thermal protection
Outputs protected against AC and DC short-
circuit to ground, supply rail or across load
Low current consumption in short-circuit to POWER OUTPUT AT d tot = 10%
220 nF
16
input 3 10
60 k
60 k
12
220 nF
17
input 4
7 11
MBC271
TDA1560Q
2
VP
2200 F 0.22 F
100 nF 2200 F
13 10 9
disable
10 k SUPPLY
17 TEMPERATURE
S1
SENSOR
TDA1560Q
diagnostic
14 output 1
VP
0.22 F
Ck
input (+) 7 output 1 ()
1
input
150 nF POWER
150 STAGE
k LOAD DUMP
TEMPERATURE
Rex = 100 k AND CURRENT
150 PROTECTION
Ck k POWER
STAGE
2 11 output 2 (+)
input ()
150 nF
INPUT AND 0.22 F
FEEDBACK
Vref CIRCUIT VP
4 1
10 F
15 k
16
mode select switch
voltage SUPPLY
3 reference disable
15 5 8 12 6
2 MCD333 - 3
TDA1561Q
VP
MUTE
1 6
IN1
OUT1
5
R OUT1
12
CIN 1/2R REFERENCE THERMAL/ HIGHER 0.5VP 11
SOURCES SHORT-CIRCUIT TEMPERATURE C 11
MUTE/STANDBY PROTECTION BTL DISABLE
3
MODE
9
2 OUT2
HVP R
8
13 OUT2
IN2
MUTE TDA1561Q
4 10
MLD214
GND1 GND2
TDA8560Q/TDA8563Q/TDA8563AQ
2 40 W BTL amplifiers
removed.
power ground (substrate)
The ampliers come in 13-pin plastic SIL power packages with
the pins bent to DIL format.
TDA8561Q/TDA8564Q
2 24 W BTL or 4 12 W amplifiers
Very few external components These are class-B power amplifiers with internally-fixed gain for
Low offset voltage (150 mV) at output (250 mV for excellent channel balance (within 1 dB). They are for BTL
stereo or quad (front and rear stereo) car audio applications. The
TDA8564Q) important for BTL
two types are identical except that the TDA8561Q has a fixed
High supply voltage ripple rejection (>48 dB closed-loop voltage gain of 26 dB (BTL)/20 dB (single-ended)
between 100 Hz and 10 kHz, Rs = 0 ) whereas that of the TDA8564Q 46 dB (BTL) and 40 dB
Load dump protection (single-ended).
Output protected against AC and DC short-circuit
A diagnostic facility senses distortion, load short-circuit and
to ground or supply rail temperature. At onset of distortion or temperature >150 C, the
Low current consumption (40 mA) during any diagnostic output signal can be used to reduce the input drive
short-circuit condition via a sound processor or DC volume control. For load short- 4
Thermal protection circuit or output short-circuit to ground or supply, the outputs
are switched-off until the short-circuit is removed.
Reverse polarity safe
Standby feature with switch-on voltage of 0 V to The amplifiers come in 17-pin plastic SIL power packages with
2 V at pin 14 and a switch-on current of only 12 A the pins bent to DIL format.
to allow use of an inexpensive-pensive switch. The
standby supply current is >100 A. The voltage at
pin 14 for normal operation is >8.5 V POWER OUTPUT AT d tot = 10%
Mute facility with switch-on voltage of 3.3 V to 6.4 V
power supply load
at pin 14 to eliminate switch-on/switch-off clicks output voltage impedance
Identical inputs (inverting and non-inverting) (W) (V) ()
Diagnostic facility senses distortion, load short- BTL stereo
2 24 14.4 4
circuit and temperature quad
Pins protected against ESD 47 14.4 4
Low thermal resistance 4 12 14.4 2
VP VP
mode mode
switch 100 2200 switch 100 2200
10 10
diagnostic nF F nF F
k k
14 16 5 13 14 16 5 13
TDA8561Q TDA8561Q
220 nF TDA8564Q 220 nF TDA8564Q
non- inverting 1 non- inverting 1
input 1 6 input 1 6
1000 F
60 60
k k
8 220 nF 8
3 inverting 3
inverting input 2 input 2 1000 F
2 60 2 60
ground (signal) ground (signal)
k k
reference reference
voltage 4 voltage
supply voltage 4 9
not connected supply voltage 1/2Vp
ripple rejection ripple rejection 9
60 60 not connected
k k
220 nF
non-inverting 17 non-inverting 17
input 4 12 input 4 12
220 nF
1000 F
60 60
k k
10 10
220 nF
15 inverting 15
inverting input 3 input 3 1000 F
7 11 7 11
MEA862 - 2 MEA863 - 2
TDA8561Q/TDA8564Q in BTL stereo configuration left, and in single-ended quad (front and rear stereo) configuration
TDA8562Q/TDA8565Q
4 12 W single-ended amplifier
4 Identical inputs
Thermal protection
Reverse polarity safe POWER OUTPUT AT d tot = 10%
Standby feature with switch-on voltage of 0 V to power supply load
output voltage impedance
2 V at pin 8 and a switch-on current of only 12 A
(W) (V) ()
to allow use of an inexpensive switch. The standby 47 14.4 4
supply current is <100 A. The voltage at pin 8 for 4 12 14.4 2
normal operation is >8.5 V
Mute facility to eliminate switch-on/switch-off
VP
clicks mode
switch 100 2200
10
Diagnostic facility for sensing distortion, short- diagnostic nF F
k
The amplifiers come in 17-pin plastic SIL power packages with 220 nF 10
15
the pins bent to DIL format. input 3 1000 F
7 11
MEA867 - 2
TDA8566Q
Differential inputs
Very high Common Mode Rejection Ratio
High common mode input signal handling capacity
Very few external components
High output power
Low offset voltage at output (<100 mV)
important for BTL POWER OUTPUT AT d tot = 10%
Fixed gain power supply load
Diagnostic facility for sensing distortion, short-
output voltage impedance 4
(W) (V) ()
circuit and temperature 2 25 14.4 4
Good ripple rejection 2 40 14.4 2
Mode-select switch (operating, mute and standby)
Load dump protection
Short-circuit proof to ground, to Vp and across the
VP1 VP2
load 1 mute 5 13
IN1+
switch
+ CM
Low power dissipation in any short circuit
2
condition IN1
VA
6
OUT1+
+
2.3
Thermally protected k
2.3 k
Reverse-polarity safe mute
(9)
switch
+ CM
Pins protected against ESD
No switch-on/switch-off clicks VA
8
OUT1
+
60 60 2.3
Low thermal resistance k k k
2.3 k
(9)
This is a class-B BTL stereo power amplifier. It features a high- n.c.
9
standby 14
MODE
impedance fully-differential balanced input stage thats also switch
TDA8566Q
capable of operating in single-ended mode (with one input VA
standby
reference
Vref
capacitively coupled to an audio ground). 3
voltage mute
switch
CLIP
4
CLIP
SGND
1
A diagnostic facility senses distortion, load short-circuit and DIAG
15
DIAG
mute
IN2+
via a sound processor or DC volume control. For load short-cir- +
switch CM
12
OUT2
VA
+
2.3
k
2.3 k
11 7 (9)
MGD105
PGND2 PGND1
TDA8567Q/TDA8568Q/TDA8569Q
4 25 W BTL amplifiers
These are class-B power amplifiers with internally fixed gain for
Vref
excellent channel balance. They are for quad (front and rear 11
IN2 + 7
stereo) car audio applications. The TDA8567Q and OUT2+
TDA8569Q have a fixed closed-loop voltage gain of 26 dB,
30 k
whilst that of the TDA8568Q is 40 dB. The TDA8569, more-
+
over, can drive loads down to 2 . 5
OUT2
12
SGND TDA8567Q/ 9
A diagnostic facility senses distortion, load short-circuit and TDA8568Q/ DIAGNOSTIC VDIAG
temperature. At onset of distortion or temperature >145 C, the 13
TDA8569Q
IN3 + 17
diagnostic output signal can be used to reduce the input drive OUT3+
via a sound processor or DC volume control. For load short-
30 k
circuit or output short-circuit to ground or supply, the outputs
+ 19
are switched-off until the short-circuit is removed OUT3
3 6 18 21
TDA8574(T)
Class-H operation means that output voltage is 14 V (peak-to-peak). This high output level significantly
swings are greater than the supply voltage improves signal-to-noise ratio of the power amplifier stage by
allowing it to operate at lower gain.
High supply voltage ripple rejection
Low distortion (0.003% THD at 1 kHz with The TDA8574 comes in a 16-pin plastic DIP and the
Vo(rms) = 3 V) TDA8574T comes in a 16-pin SO package for surface mount-
Low noise (noise output of typ. 5 V) ing.
Supply voltage range of 6 V to 12 V
All pins ESD protected
4
These two-channel class-H amplifiers with single-ended outputs
offer 8 dB voltage gain and low distortion. Theyre principally
POWER OUTPUT AT d tot = 0.1%
for eliminating ground noise in car and mains-powered applica-
tions with long connections between the signal sources and out- AC supply load
put amplifiers (or boosters). Class-H operation ensures that volt- output voltage impedance
age swings over the load are greater than the supply voltage: with (Vrms) (V) ()
a supply voltage of 9 V, the output voltage swing across the load 5 9 10 k
VCCL 1
36 k
BUFFER VCCL 16
CL+
24 k
3
15
CL
SVRL + LIFT
AMP.
BUFFER
30 k
SIGNAL
+ AMP. 13
OUTL
REFERENCE VCCL
2
INL 14
4 LGND
INML
TDA8574(T) 5
5
INMR 11
7 RGND
INR
VCCR
REFERENCE
12
OUTR
+ SIGNAL
AMP.
30 k
BUFFER
LIFT
SVRR
6 + AMP. 10
CR
24 k 9
VCCR CR+
BUFFER
8 36 k
VCCR
MGE668
TDA8576T
Class-H operation means that output voltage swings over the load are greater than the supply voltage: with a
swings are greater than the supply voltage supply voltage of 9 V, the output voltage swing across the load is
14 V (peak-to-peak). This high output level significantly
High supply voltage ripple rejection
improves signal-to-noise ratio of the power amplifier stage by
Low distortion (0.005% THD at 1 kHz with allowing it to operate at lower gain.
Vo(rms) = 3 V)
Low noise (noise output of typ. 5 V) The TDA8576T comes in a 16-pin SO package for surface
mounting.
Supply voltage range of 6 V to 12 V
All pins ESD protected
4
POWER OUTPUT AT d tot = 0.1%
This two-channel class-H amplifier with single-ended outputs
offers 6 dB voltage gain and low distortion. Its principally for AC supply load
eliminating ground noise in car and mains-powered applications output voltage impedance
with long connections between the signal sources and output (Vrms) (V) ()
amplifiers (or boosters). Class-H operation ensures that voltage 5 9 10 k
VCCL 1
36 k
BUFFER VCCL 16
CL+
36 k
15
CL
+ LIFT
AMP.
3 BUFFER
SVRL 20 k
SIGNAL
+ AMP. 13
OUTL
REFERENCE VCCL
2
INL 14
4 LGND
INML
TDA8576T 5
5
INMR 11
7 RGND
INR
VCCR
REFERENCE
12
OUTR
+ SIGNAL
AMP.
6
SVRR 20 k
BUFFER
LIFT
+ AMP. 10
CR
36 k 9
VCCR CR+
BUFFER
8 36 k
VCCR
MGE671
100 nF 2200 F
Common-mode rejection is independent of source
220 nF
resistance 9
1 2.2 F
Few peripheral components left 8 left
input output
2 VCC
65 dB supply voltage ripple rejection with Rs =
10 F TDA8577 47 F
2 k 5
VP
Low power consumption 10 F 2
supply
0.2 sec DC input voltage settling time VP
100 nF 2200 F
10 F 2
The TDA8577 comes in an 9-pin plastic SIL package and the 6
2.2 F
TDA8578(T) comes in a 16-pin plastic DIL or SO package. 11
right right
These two types have completely separated inputs. The input 220 nF output
7
TDA8579(T) has linked inverting inputs and comes in an 8-pin 9
plastic DIL or SO package.
MBD217 - 1
VP
100 nF 2200 F
220 nF
8
1 2.2 F
7 left
output
left VCC
input
22 F TDA8579 47 F
2 VP 4
2
right 2.2 F
input
6 right
220 nF output
3
5 MBD232 - 1
MAINS-POWERED
SYSTEMS INCLUDING
HI-FI AND TV SOUND
TDA1013B
1 F
0.1 F 220 k
VP
0.1 470
6 5 4 3 F F
220 nF
8
input 2
CONTR. AUDIO
UNIT AMP.
0.1 470
TDA1013B F F
9 7 1
DC 3.3
volume
control
MSA613
TDA1514A
High ripple rejection of 72 dB With its high power output and high performance, this amplifi-
Standby feature with an activation level of <1 V at er is ideal for top quality mains-powered hi-fi systems, radios,
TV sets and digital audio systems.
pin 3. The supply voltage to obtain the standby
state is 4.5 V to 7 V. The standby supply current The output transistors have total thermal and SOAR protection,
is 20 mA. and the circuit embodies a special mute facility that operates for
Mute facility with an activation level of 2 V to 4.5 V a short period after switch-on to eliminate switch-on/switch-off
clicks. This period is preset by external components.
at pin 3
Thermal protection The IC can operate from either asymmetrical or symmetrical
Good supply voltage ripple rejection power supplies (7.5 V to 30 V) and comes in a 9-pin plastic
Signal to noise ratio is 82 dB at Po = 50 mW, SIL power package.
Rs = 2 k
High slew rate (10 V/s)
Output protected against AC short-circuit
(asymmetrical power supply) and DC short-circuit
5
(symmetrical power supply) via SOAR protection
Externally adjustable closed-loop voltage gain of
20 dB to 46 dB
Low output offset voltage (2 mV) also allows 2
POWER OUTPUT WITH Vp = 27.5 V, RL = 8
TDA1514A to be used in BTL configuration to
power dtot dtot
obtain output powers up to 100 W (see next page) output*
(W) (%) (dB)
32 (40) 0.003 -90
40 (50) 0.1 -60
51 (65) 10 -20
* values between brackets are for Vp = 24 V, RL = 4
VP
82 470
nF
1 F 150 2.2 mF
1 6 7
input
220 F
20 47
220 5
pF k F
9 TDA1514A
22 nF
680 PROTECTION
3.3
MUTE/STANDBY
SOAR THERMAL
2.2 mF
8 3 2 4
3.3 F
470
VP
470 nF
20 k
MSB408
2 TDA1514A
VP
470 nF 470 nF
7 6 6 7
1 F
1 1
input
20 5 5 20
220 2.2 mF
k k
pF 1 F
22 nF
9 9
22 nF
47
3.3 2.2 nF F
TDA1514A 3.3 TDA1514A
100
8 3 2 4 20 k 20 k 4 2 3 8
22 F
1.3 k
VP
MSB409
TDA1521(Q)/TDA2616(Q) AND VP
TDA1521A/TDA2615 100 nF
680 F
7
20 k
to
pin 5
5
2
4
1
The TDA1521(Q) and TDA1521A, and the TDA2615 and input 1
22 nF
TDA2616(Q) are pin-compatible amplifiers for mains-powered 220 nF
20 k
applications such as stereo TV sound channels and stereo radio. 3
TDA1521(A)
8.2
2 12 ** 16 8 680 20 k 8.2 R L= 8
26 12 8
5
2 10 12 4
MLA940 - 1
TDA1521A/TDA2615: stereo
26 12 8 TDA2615/TDA2616 in single-ended stereo configuration
* 26 W at dtot = 10% ** 2 15 W at dtot = 10%
MSB415
5 3 2
7
6 W hi-fi amplifiers VP
to internal 1/2 VP
FURTHER INFORMATION
Data
Data on our semiconductors for radio/audio systems are avail- 10. 6.5 W stereo hi-fi audio amplifier for mains-fed applica-
able in loose data sheets or are given in Philips Semiconductors tions Philips Semiconductors Application Note
data handbook IC01a (ordering code 9398 183 00011) and NBA/AN9110.
IC01b (ordering code 9398 183 10011).
11. 12 W stereo hi-fi audio amplifier (20 W BTL) Philips
Data for our semiconductors for TV and video systems are avail- Semiconductors Application Note NBA/AN9205.
able in loose data sheets or a given in Philips Semiconductors
data handbooks IC02a (ordering code 9398 652 23011), IC02b 12. TDA7052A; 1 W BTL mono audio amplifier with DC vol-
(ordering code 9398 652 24011) and IC02c (ordering code ume control Philips Semiconductors Application Note
9398 652 24011). NBA/AN9207.
1. TDA1013B Audio amplifier with DC volume control 14. TDA7056A; 3 W BTL mono audio amplifier with DC
Philips Semiconductors Application Note NBA/AN9005. volume control Philips Semiconductors Application Note
NBA/AN9208.
2. Recorder IC TDA1016 for portable applications Philips
Semiconductors Application Note NBA8301. 15. 3 W mono BTL audio amplifier Philips Semiconductors
Application Note NBA/AN9009.
3. TDA1514A Hi-fi power amplifiers Philips Semiconductors
A Application Note NBA/AN8911. 16. TDA7057 3 W componentless BTL stereo audio amplifier
Philips Semiconductors Application Note NBA/AN9009.
4. Audio power ICs for car radios Philips Semiconductors
Application Note NBA9001 (ordering code: 9398 078 17. TDA1560Q power lifting amplifier (class-H) Philips
30011). Semiconductors Application Note NBA/AN9206.