Professional Documents
Culture Documents
Plastic Analysis of Structures PDF
Plastic Analysis of Structures PDF
References
1 Marshall and Nelson, Structures.
2 Norris, Wilbur and Utku, Elementary Structural Analysis
3 Sir John Baker and J Heyman: Plastic Design of Frames. (Cambridge University Press)
In the elastic design methods the assumption is made that the stresses are kept below the elastic limit and
that when the load is removed the structure will revert to its original shape. Furthermore one assumes that
strain is directly proportional to stress. This theory works well for most building materials under normal loads.
It, however, does not work when one tries to determine the failure strength of structures.
In the plastic analysis method we are more interested in the strength of the structure. The applied load may
not be greater than a predetermined portion of the load that will cause failure. This failure could be strength
or serviceability.
Certain materials such as steel have the ability to maintain load even though the yield stress has been
reached.
Investigate the stress distribution of a profile that has properties shown in the Figure 1.
Rectangular Profile
1 h 2 1
Elastic: Me = b h fy = bh 2 fy
2 2 3 6
h 1 1
Plastic: Mp = b h fy = bh 2 fy
2 2 4
Mp Zp 6
Shape factor: F= = = = 1,5
Me Ze 4
When the profile is fully plastic, rotation can take place without an increase in the bending moment. A plastic
hinge has then been formed. The bending moment will also change as the profile stresses increase from
elastic to fully plastic.
q L2 12 Me q p L2 16 M p
Elastic: Me = e ; thus qe = Plastic: 2 M p = ; thus q p =
12 L2 8 L2
Failure will occur when enough plastic hinges have formed to lead to a mechanism. Normally this is one
more plastic hinge than the number of redundancies.
Enough assumptions are made so that the bending moment diagram can be solved using the equilibrium
equations. Nowhere may the moment be greater than the assumed plastic moment.
Example:
A uniform beam is loaded as in the sketch. Determine the plastic moment Mp that will just cause the beam to
fail.
The beam is statically indeterminate to the first degree: Two plastic hinges are required.
1 Assume that the negative moment at A is numerically equal to the positive moment at C.
2
5 VA = 2 MA
VA = 0,4 MA
201
It follows that M A = = 52,89 kN m
3,8
VA is then = 2,16 kN
(39 VA )3 = MA en
9 VA - 2 MA 21 x 4 = 0
It follows that MA = 53,40 kN.m
VA = 2,20 kN
The biggest bending moment occurs in two places, namely A and C with a value = 53,4 kN.m. MP =
53,4 kN.m.
The load, that is in equilibrium with arbitrary values of the redundancies and where the bending
moment is nowhere greater than the maximum plastic moment, is never greater than the failure load.
Positions are assumed for the plastic hinges and virtual work is used to determine the ratio between loads
and the bending moment at the plastic hinges.
Mechanism 2 leads to the biggest value of Mp and is hence the critical mechanism.
A load that is determined by using virtual work based on an arbitrary mechanism is never smaller than the
failure load.
1 Equilibrium conditions: The moments must be in equilibrium with the applied loads.
2 Failure conditions: no bending moment in the structure may be greater than the plastic moment.
3 Mechanism conditions: enough plastic hinges must form to form a mechanism.
Example:
Mechanism 3 gives the biggest value of Mp = 24,3 kN.m and is thus the critical mechanism.
The answer may be checked by calculating the bending moment diagram.
1,0 + 1,5
HD = M p = 15,179 kN
4
H A = 20 HD = 4,821 kN
Nowhere in the structure is the bending moment greater than the calculated plastic moment. Enough plastic
hinges have formed to create a mechanism.
Mechanism 3 may be seen as a combination of mechanisms 1 and 2. The virtual work at the hinges is equal
to 4 + 5 2 = 7, where the negative 2 is for the hinge that is removed at B (mechanism 1: clockwise,
mechanism 2: anti-clockwise). The virtual work done by the loads is equal to 90 + 80 = 170. Mechanisms 1
and 2 can be seen as independent and mechanism 3 as derived from the independent mechanisms..
The bending moment diagram of any structure may be determined if the bending moment at enough possible
hinge positions is chosen. The moments at these points are not independent: they are linked by the
equilibrium equations. For every possible hinge position we are able to derive an equilibrium equation in
terms of the loads and the redundancies. From these equations it is possible to eliminate the redundancies
and to derive a set of equilibrium equations that gives the link between the bending moments at possible
hinge positions. The number of these independent equilibrium equations is equal to the number of possible
hinge positions minus the redundancies.
A mechanism is formed when the equilibrium equations are no longer satisfied. The number of independent
mechanisms is also equal to the number of independent equilibrium equations. Therefore:
Combine mechanisms to find big virtual work by the loads and minimum work by the hinges.
Example:
In the following table the independent mechanisms are numbered 1 to 4. Mechanism 4 cannot occur in
isolation but may be combined with other mechanisms to eliminate hinges.
Example
Example:
If one uses the XY as the basis of the zero line, we are back to the bending moment diagram of the propped
cantilever.
7
1) If M A M C then 83,75 MA = MA leads to MA = 52,89 kN.m
12
and MC = 52,89 kN.m
MD = 53,53 kN.m
If one had to design the beam for an Mp = 53,3 kN.m, then we would not have a failure mechanism and the
beam would be able to carry a greater load.
3
2) If M A = MD then 66,75 MA = MA leads to MA = 53,40 kN.m
12
And MC = 52,60 kN.m
MD = 53,40 kN.m
If Mp = 53,40 kN.m then we have a failure mechanism.
Example
The example is statically indeterminate to the first degree. To make the structure statically determinate,
remove the horizontal reaction at D as the redundancy. Draw the bending moment diagram of the statically
determinate structure for the load as well as for the redundancy.
The maximum positive moment between BC for the statically determinate structure is at X1 at a distance of
4,576 m with a value of 132,28 kN.m. Assume plastic hinges at X1 and C.
Remove the redundancy at I, and determine the bending moment diagram of the statically determinate
structure for the given load as well as the redundancy. Fold the bending moments open and super-impose
the bending moments. From the sketch it appears that the biggest moments are at D and H.
At D, 252,7 8,6667 H = + Mp
At H, 06H = - Mp
It follows that 17,229 kN and Mp = 103,377 kN.m. Redraw the bending moment diagramme and ensure that
the value of 103,377 is not exceeded.