Professional Documents
Culture Documents
RAN14 0 Feature Activation Guide PDF
RAN14 0 Feature Activation Guide PDF
Issue 05
Date 2012-12-31
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective holders.
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and the
customer. All or part of the products, services and features described in this document may not be within the
purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information,
and recommendations in this document are provided "AS IS" without warranties, guarantees or representations
of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.
Website: http://www.huawei.com
Email: support@huawei.com
Purpose
This document provides guidelines for enabling or disabling a feature after initial configuration.
Based on the activation, verification, and deactivation of a feature in the feature list, the
guidelines aim to ensure that the feature is available on the network.
This document describes how to activate a license and configure a feature in RAN.
NOTE
The BSC6900 is used as an example to describe the network controller in this document.
Product Version
The solution version is RAN14.0 related to this document, for more details you can refer to the
following table.
BSC6900 V900R014C00
NodeB V100R014
NodeB V200R014
Intended Audience
This document is intended for:
l Technical support engineers
l Maintenance engineers
l Field engineers
l Network optimization engineers
Organization
1 Changes in the RAN Feature Activation Guide
This chapter describes the changes in the RAN Feature Activation Guide.
2 Feature Activation and License Item Descriptions
RANFeatures are classified into basic and optional features. Basic features are not license-
controlled and therefore do not require license activation before use. Some optional features are
license-controlled and therefore require license activation before use. If the Configuration
Method column for a basic feature in the RAN basic feature list is None, enabling this feature
does not involve any configurations. If the Configuration Method column for an optional feature
in the RAN optional feature list is None, this feature is enabled once it is activated.
3 Overview of Configurations on the CME
This section provides an overview of the configuration on the CME. The CME is a configuration
tool on GUIs assisting you to effectively configure the data about wireless NE features. You can
reconfigure configuration parameters by using the configuration expresses provided by the CME
to activate or deactivate specified features.
4 Activating the UMTS License
In the case of certain UMTS features, a license control item is defined for each feature. The
license control item of a feature must be activated before the configuration and use of the feature.
The license control items related to the RNC can be activated on the M2000 or RNC LMT,
whereas those related to the NodeB can be activated only on the M2000.
5 Configuring 3.4/6.8/13.6/27.2Kbps RRC Connection and Radio Access Bearer
Establishment and Release
This section describes how to activate, verify, and deactivate the basic feature WRFD-010510
3.4/6.8/13.6/27.2Kbps RRC Connection and Radio Access Bearer Establishment and Release.
6 Configuring Conversational QoS Class
This section describes how to activate, verify, and deactivate the basic feature WRFD-010501
Conversational QoS Class.
7 Configuring Streaming QoS Class
This section describes how to activate, verify, and deactivate the basic feature WRFD-010502
Streaming QoS Class.
8 Configuring Interactive QoS Class
This section describes how to activate, verify, and deactivate the basic feature WRFD-010503
Interactive QoS Class.
9 Configuring Background QoS Class
This section describes how to activate, verify, and deactivate the basic feature WRFD-010504
Background QoS Class.
10 Configuring Emergency Call
This section describes how to activate, verify, and deactivate the basic feature WRFD-021104
Emergency Call.
11 Configuring RAB Quality of Service Renegotiation over Iu Interface
This section describes how to activate, verify, and deactivate the basic feature WRFD-010506
RAB Quality of Service Renegotiation over Iu Interface.
This section describes how to activate, verify, and deactivate the basic feature WRFD-010801
Intra RNC Cell Update.
37 Configuring Inter RNC Cell Update
This section describes how to activate, verify, and deactivate the basic feature WRFD-010802
Inter RNC Cell Update.
38 Configuring Intra RNC URA Update
This section describes how to activate, verify, and deactivate the basic feature WRFD-010901
Intra RNC URA Update.
39 Configuring Inter RNC URA Update
This section describes how to activate, verify, and deactivate the basic feature WRFD-010902
Inter RNC URA Update.
40 Configuring Direct Signaling Connection Re-establishment (DSCR)
This section describes how to activate, verify, and deactivate the basic feature WRFD-021400
Direct Signaling Connection Re-establishment (DSCR).
41 Configuring CS Fallback Guarantee for LTE Emergency Calls
This section describes how to activate, verify, and deactivate the basic feature WRFD-140102
CS Fallback Guarantee for LTE Emergency Calls. For details about how to configure this feature
on the LTE side, see the related documents provided by the LTE equipment vendor.
42 Configuring NodeB Clock
This section describes how to activate, verify, and deactivate the basic feature MRFD-210501
NodeB Clock.
43 Configuring Dynamic AAL2 Connections in Iub/IuCS/Iur Interface
This section describes how to activate, verify, and deactivate the basic feature WRFD-05030104
Dynamic AAL2 Connections in Iub/IuCS/Iur Interface.
44 Configuring Permanent AAL5 Connections for Control Plane Traffic
This section describes how to activate, verify, and deactivate the basic feature WRFD-05030105
Permanent AAL5 Connections for Control Plane Traffic.
45 Configuring Call Admission Based on Used AAL2 Path Bandwidth
This section describes how to activate, verify, and deactivate the basic feature WRFD-05030106
Call Admission Based on Used AAL2 Path Bandwidth.
46 Configuring CBR, rt-VBR, nrt-VBR, UBR ATM QoS Classes
This section describes how to activate, verify, and deactivate the basic feature
"WRFD-05030107 CBR, rt-VBR, nrt-VBR, UBR ATM QoS Classes".
47 Configuring F5
This section describes how to activate, verify, and deactivate the basic feature WRFD-05030110
F5. (This feature cannot be configured using the CME. )
48 Configuring UBR+ ATM QoS Class
This section describes how to activate, verify, and deactivate the basic feature "WRFD-050305
UBR+ ATM QoS Class".
This section describes how to activate, verify, and deactivate the basic feature MRFD-210103
Link Aggregation.
This section describes how to activate, verify, and deactivate the basic feature WRFD-040100
Flow Control.
51 Configuring BOOTP
This section describes how to activate, verify, and deactivate the basic feature WRFD-031100
BOOTP. In ATM transport mode, the NodeB can automatically set up the OM channel with the
BSC6900 by using the BOOTSTRAP Protocol (BOOTP) function.
This section describes how to activate, verify, and deactivate the basic feature WRFD-031101
NodeB Self-Discovery Based on IP Mode.
This section describes how to activate, verify, and deactivate the basic feature WRFD-040300
License Control for Urgency. (This feature cannot be configured using the CME. )
This section describes how to activate, verify, and deactivate the basic feature WRFD-031000
Intelligently Out of Service.
55 Configuring OCNS
This section describes how to activate, verify, and deactivate the basic feature WRFD-031200
OCNS (Orthogonal Channel Noise Simulator). (This feature cannot be configured using the
CME. )
This section describes how to activate, verify, and deactivate the basic feature WRFD-031400
Power Off the Equipment Level by Level.
This section describes how to activate, verify, and deactivate the basic feature WRFD-031500
Solar Power Device Management.
This section describes how to activate, verify, and deactivate the basic feature MRFD-210601
Connection with TMA (Tower Mounted Amplifier). (This feature cannot be configured using
the CME. )
This section describes how to activate, verify, and deactivate the basic feature MRFD-210602
Remote Electrical Tilt. (This feature cannot be configured using the CME. )
This section describes how to activate, verify, and deactivate the basic feature WRFD-060003
Configuring Same Band Antenna Sharing Unit (900 MHz). (This feature cannot be configured
using the CME. )
61 Configuring VoIP over HSPA/HSPA+
This section describes how to activate, verify, and deactivate the optional feature WRFD-010617
VoIP over HSPA/HSPA+.
62 Configuring Optimized Scheduling for VoIP over HSPA
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061703 Optimized Scheduling for VoIP over HSPA.
63 Configuring IMS Signaling over HSPA
This section describes how to activate, verify, and deactivate the basic feature WRFD-010618
IMS Signaling over HSPA.
64 Configuring PDCP Header Compression (RoHC)
This section describes how to activate, verify, and deactivate the optional feature WRFD-011501
PDCP Header Compression (RoHC).
65 Configuring CS Voice over HSPA/HSPA+
This section describes how to activate, verify, and deactivate the optional feature WRFD-010619
CS Voice over HSPA/HSPA+.
66 Configuring AMR-WB (Adaptive Multi Rate Wide Band)
This section describes how to activate, verify, and deactivate the optional feature WRFD-010613
AMR-WB (Adaptive Multi Rate Wide Band). (This feature cannot be configured using the
CME. )
67 Configuring AMR/WB-AMR Speech Rates Control
This section describes how to activate, verify, and deactivate the basic feature WRFD-020701
AMR/WB-AMR Speech Rates Control.
68 Configuring TFO/TrFO
This section describes how to activate, verify, and deactivate the optional feature WRFD-011600
TFO/TrFO.
69 Configuring AMR Voice Quality Improvement Based on PLVA
This section describes how to activate, verify, and deactivate the optional feature WRFD-140201
AMR Voice Quality Improvement Based on PLVA.
70 Configuring Cell Broadcast Service
This section describes how to activate, verify, and deactivate the optional feature WRFD-011000
Cell Broadcast Service.
71 Configuring Simplified Cell Broadcast
This section describes how to activate, verify, and deactivate the optional feature WRFD-011001
Simplified Cell Broadcast.
72 Configuring Warning of Disaster
This section describes how to activate, verify, and deactivate the optional feature WRFD-020127
Warning of Disaster.
73 Configuring MBMS Introduction Package
This section describes how to activate, verify, and deactivate the optional feature WRFD-010616
MBMS Introduction Package.
74 Configuring MBMS Admission Control
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061602 MBMS Admission Control.
75 Configuring MBMS Load Control
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061603 MBMS Load Control.
76 Configuring MBMS Transport Resource Management
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061605 MBMS Transport Resource Management.
77 Configuring Streaming Service on MBMS
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061606 Streaming Service on MBMS.
78 Configuring 16/32/64/128Kbps Channel Rate on MBMS
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061608 16/32/64/128Kbps Channel Rate on MBMS.
79 Configuring MBMS Phase 2
This section describes how to activate, verify, and deactivate the optional feature WRFD-010660
MBMS Phase 2.
80 Configuring MBMS Enhanced Broadcast Mode
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01066001 MBMS Enhanced Broadcast Mode.
81 Configuring MBMS P2P over HSDPA
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01066002 MBMS P2P over HSDPA.
82 Configuring MBMS Admission Enhancement
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01066003 MBMS Admission Enhancement.
83 Configuring Inter-Frequency Neighboring Cell Selection for MBMS PTP Users
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01066004 Inter-Frequency Neighboring Cell Selection for MBMS PTP Users.
84 Configuring FACH Transmission Sharing for MBMS
This section describes how to activate, verify, and deactivate the optional feature WRFD-010627
FACH Transmission Sharing for MBMS.
This section describes how to activate, verify, and deactivate the optional feature WRFD-010612
HSUPA Introduction Package.
98 Configuring HSUPA Admission Control
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061202 HSUPA Admission Control.
99 Configuring HSUPA Power Control
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061203 HSUPA Power Control.
100 Configuring HSUPA Mobility Management
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061204 HSUPA Mobility Management.
101 Configuring HSUPA DCCC
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061208 HSUPA DCCC.
102 Configuring 20 HSUPA Users per Cell
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061211 20 HSUPA Users per Cell.
103 Configuring HSUPA Iub Flow Control in Case of Iub Congestion
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061212 HSUPA Iub Flow Control in Case of Iub Congestion.
104 Configuring HSUPA E-AGCH Power Control (Based on CQI or HS-SCCH)
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061401 HSUPA E-AGCH Power Control (Based on CQI or HS-SCCH).
105 Configuring HSUPA 2ms TTI
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061403 HSUPA 2ms TTI.
106 Configuring HSUPA 2 ms/10 ms TTI Handover
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061404 HSUPA 2 ms/10 ms TTI Handover.
107 Configuring HSUPA 5.74Mbps per User
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061405 HSUPA 5.74Mbps per User.
108 Configuring Streaming Traffic Class on HSUPA
This section describes how to activate, verify, and deactivate the optional feature WRFD-010632
Streaming Traffic Class on HSUPA.
109 Configuring HSUPA over Iur
This section describes how to activate, verify, and deactivate the optional feature WRFD-010635
HSUPA over Iur.
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061001 15 Codes per Cell.
123 Configuring Time and HS-PDSCH Codes Multiplex
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061018 Time and HS-PDSCH Codes Multiplex.
124 Configuring HSDPA H-ARQ & Scheduling (MAX C/I, RR, and PF)
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061009 HSDPA H-ARQ & Scheduling (MAX C/I, RR, and PF).
125 Configuring HSDPA Static Code Allocation and RNC-Controlled Dynamic Code
Allocation
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061005 HSDPA Static Code Allocation and RNC-Controlled Dynamic Code
Allocation.
126 Configuring HSDPA Power Control
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061004 HSDPA Power Control.
127 Configuring HSDPA Admission Control
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061003 HSDPA Admission Control.
128 Configuring Improvement of User Experience in Low Traffic Service
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061020 Improvement of User Experience in Low Traffic Service.
129 Configuring HSDPA Flow Control
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061010 HSDPA Flow Control.
130 Configuring HSDPA Mobility Management
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061006 HSDPA Mobility Management.
131 Configuring HSDPA UE Category 1 to 28
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061002 HSDPA UE Category 1 to 28.
132 Configuring DL 16QAM Modulation
This section describes how to activate, verify, and deactivate the optional feature WRFD-010629
DL 16QAM Modulation.
133 Configuring Dynamic Code Allocation Based on NodeB
This section describes how to activate, verify, and deactivate the optional feature WRFD-010631
Dynamic Code Allocation Based on NodeB.
134 Configuring HSDPA Enhanced Package
This section describes how to activate, verify, and deactivate the optional feature WRFD-010611
HSDPA Enhanced Package.
135 Configuring Scheduling based on EPF and GBR
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061103 Scheduling based on EPF and GBR.
136 Configuring HSDPA State Transition
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061111 HSDPA State Transition.
137 Configuring HSDPA DRD
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061112 HSDPA DRD.
138 Configuring HS-DPCCH Preamble Support
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061113 HS-DPCCH Preamble Support.
139 Configuring Streaming Traffic Class on HSDPA
This section describes how to activate, verify, and deactivate the optional feature WRFD-010630
Streaming Traffic Class on HSDPA.
140 Configuring HSDPA over Iur
This section describes how to activate, verify, and deactivate the optional feature WRFD-010651
HSDPA over Iur.
141 Configuring SRB over HSDPA
This section describes how to activate, verify, and deactivate the optional feature WRFD-010652
SRB over HSDPA.
142 Configuring CQI Adjustment Based on Dynamic BLER Target
This section describes how to activate, verify, and deactivate the optional feature WRFD-030010
CQI Adjustment Based on Dynamic BLER Target.
143 Configuring MIMO Prime
This chapter describes how to activate, verify, and deactivate the basic feature WRFD-030011
MIMO Prime.
144 Configuring Adaptive Configuration of Typical HSPA Rate
This section describes how to activate, verify, and deactivate the optional feature WRFD-030004
Adaptive Configuration of Typical HSPA Rate.
145 Configuring HSDPA Scheduling Based on UE Location
This section describes how to activate, verify, and deactivate the optional feature WRFD-140221
HSDPA Scheduling Based on UE Location.
146 Configuring Adaptive Adjustment of HSUPA Small Target Retransmissions
This section describes how to activate, verify, and deactivate the optional feature WRFD-140222
Adaptive Adjustment of HSUPA Small Target Retransmissions.
This section describes how to activate, verify, and deactivate the optional feature WRFD-010696
DC-HSDPA.
160 Configuring HSPA+ Uplink 23 Mbit/s per User
This section describes how to activate, verify, and deactivate the optional feature WRFD-140203
HSPA+ Uplink 23 Mbit/s per User.
161 Configuring DC-HSUPA
This section describes how to activate, verify, and deactivate the optional feature WRFD-140204
DC-HSUPA.
162 Configuring Downlink Enhanced CELL_FACH
This section describes how to activate, verify, and deactivate the optional feature WRFD-010688
Downlink Enhanced CELL_FACH.
163 Configuring Performance Improvement of MIMO and HSDPA Co-carrier
This section describes how to activate, verify, and deactivate the optional feature WRFD-010700
Performance Improvement of MIMO and HSDPA Co-carrier.
164 Configuring CPC - DTX /DRX
This section describes how to activate, verify, and deactivate the optional feature WRFD-010686
CPC - DTX /DRX.
165 Configuring CPC - HS-SCCH less operation
This section describes how to activate, verify, and deactivate the optional feature WRFD-010687
CPC - HS-SCCH less operation.
166 Configuring E-DPCCH Boosting
This section describes how to activate, verify, and deactivate the optional feature WRFD-010697
E-DPCCH Boosting.
167 Configuring Uplink Enhanced CELL_FACH
This section describes how to activate, verify, and deactivate the optional feature WRFD-010701
Uplink Enhanced CELL_FACH.
168 Configuring 96 HSDPA Users per Cell
This section describes how to activate, verify, and deactivate the optional feature WRFD-010653
96 HSDPA Users per Cell.
169 Configuring 96 HSUPA Users per Cell
This section describes how to activate, verify, and deactivate the optional feature WRFD-010639
96 HSUPA Users per Cell.
170 Configuring 128 HSDPA Users per Cell
This section describes how to activate, verify, and deactivate the optional feature WRFD-010654
128 HSDPA Users per Cell.
171 Configuring 128 HSUPA Users per Cell
This section describes how to activate, verify, and deactivate the optional feature WRFD-010670
128 HSUPA Users per Cell.
This section describes how to activate, verify, and deactivate the optional feature
WRFD-02131102 Dedicated NodeB/Cell for Operators.
197 Configuring MOCN Mobility Management
This section describes how to activate, verify, and deactivate the optional feature
WRFD-02131103 MOCN Mobility Management.
198 Configuring MOCN Load Balance
This section describes how to activate, verify, and deactivate the optional feature
WRFD-02131104 MOCN Load Balance.
199 Configuring Routing Roaming UEs in Proportion
This section describes how to activate, verify, and deactivate the optional feature
WRFD-02131106 Routing Roaming UEs in Proportion.
200 Configuring MOCN Cell Resource Demarcation
This section describes how to activate, verify, and deactivate the optional feature WRFD-140223
MOCN Cell Resource Demarcation.
201 Configuring HCS (Hierarchical Cell Structure)
This section describes how to activate, verify, and deactivate the optional feature WRFD-021200
HCS (Hierarchical Cell Structure).
202 Configuring One Tunnel
This section describes how to activate, verify, and deactivate the optional feature WRFD-020111
One Tunnel.
203 Configuring Overbooking on ATM Transmission
This section describes how to activate, verify, and deactivate the optional feature WRFD-050405
Overbooking on ATM Transmission.
204 Configuring ATM Switching-Based Hub NodeB
This section describes how to activate, verify, and deactivate the optional feature WRFD-050105
ATM Switching-Based Hub NodeB.
205 Configuring AAL2 Switching-Based Hub NodeB
This section describes how to activate, verify, and deactivate the optional feature WRFD-050106
AAL2 Switching-Based Hub NodeB.
206 Configuring IP Transmission Introduction on Iub Interface
This section describes how to activate, verify, and deactivate the optional feature WRFD-050402
IP Transmission Introduction on Iub Interface. (This feature cannot be configured using the
CME. )
207 Configuring Hybrid Iub IP Transmission
This section describes how to activate, verify and deactivate the optional feature WRFD-050403
Hybrid Iub IP Transmission.
208 Configuring ATM/IP Dual Stack NodeB
This section describes how to activate, verify, and deactivate the optional feature WRFD-050404
ATM/IP Dual Stack NodeB.
This section describes how to activate, verify, and deactivate the optional feature WRFD-050108
Satellite Transmission on Iu Interface.
222 Configuring Clock Synchronization on Ethernet in NodeB
This section describes how to activate, verify, and deactivate the optional feature WRFD-050501
Clock Synchronization on Ethernet in NodeB.
223 Configuring Synchronous Ethernet
This section describes how to activate, verify, and deactivate the optional feature WRFD-050502
Synchronous Ethernet.
224 Configuring Ethernet OAM
This section describes how to activate, verify, and deactivate the optional feature WRFD-050425
Ethernet OAM. (This feature cannot be configured using the CME. )
225 Configuring RNC Node Redundancy
This section describes how to activate, verify, and deactivate the optional feature WRFD-040202
RNC Node Redundancy.
226 Configuring RRU Redundancy
This section describes how to activate, verify, and deactivate the optional feature WRFD-040203
RRU Redundancy.
227 Configuring Iu Flex
This section describes how to activate, verify, and deactivate the optional feature WRFD-021302
Iu Flex.
228 Configuring Iu Flex Load Distribution Management
This section describes how to activate, verify, and deactivate the optional feature WRFD-021306
Iu Flex Load Distribution Management.
229 Configuring Transmit Diversity
This section describes how to activate, verify, and deactivate the optional feature WRFD-010203
Transmit Diversity. Transmit diversity enables the NodeB to provide twice the number of RF
DL channels compared with no transmit diversity.
230 Configuring 4-Antenna Receive Diversity
This section describes how to activate, verify, and deactivate the optional feature WRFD-010209
4-Antenna Receive Diversity.
231 Configuring Extended Cell Coverage up to 200km
This section describes how to activate, verify, and deactivate the optional feature WRFD-021308
Extended Cell Coverage up to 200km.
232 Configuring HSUPA Coverage Enhancement at UE Power Limitation
This section describes how to activate, verify, and deactivate the optional feature WRFD-020138
HSUPA Coverage Enhancement at UE Power Limitation.
233 Configuring Flexible frequency bandwidth of UMTS carrier
This section describes how to activate, verify, and deactivate the optional feature WRFD-021001
Flexible frequency bandwidth of UMTS carrier.
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061505 Combination of Four PS Services.
247 Configuring Inter Frequency Load Balance
This section describes how to activate, verify, and deactivate the optional feature WRFD-020103
Inter Frequency Load Balance.
248 Configuring Domain Specific Access Control (DSAC)
This section describes how to activate, verify, and deactivate the optional feature WRFD-020114
Domain Specific Access Control (DSAC).
249 Configuring Enhanced Multiband Management
This section describes how to activate, verify, and deactivate the optional feature WRFD-020160
Enhanced Multiband Management.
250 Configuring DRD Introduction Package
This section describes how to activate, verify, and deactivate the optional feature WRFD-020400
DRD Introduction Package.
251 Configuring Intra System Direct Retry
This section describes how to activate, verify, and deactivate the optional feature
WRFD-02040001 Intra System Direct Retry.
252 Configuring Inter System Direct Retry
This section describes how to activate, verify, and deactivate the optional feature
WRFD-02040002 Inter System Direct Retry.
253 Configuring Inter-System Redirect
This section describes how to activate, verify, and deactivate the optional feature
WRFD-02040003 Inter System Redirect.
254 Configuring Traffic Steering and Load Sharing During RAB Setup
This section describes how to activate, verify, and deactivate the optional feature
WRFD-02040004 Traffic Steering and Load Sharing During RAB Setup.
255 Configuring Measurement Based Direct Retry
This section describes how to activate, verify, and deactivate the optional feature WRFD-020402
Measurement Based Direct Retry.
256 Configuring Service Steering and Load Sharing in RRC Connection Setup
This section describes how to activate, verify, and deactivate the optional feature WRFD-020120
Service Steering and Load Sharing in RRC Connection Setup.
257 Configuring Uplink Flow Control of User Plane
This section describes how to activate, verify, and deactivate the optional feature WRFD-020124
Uplink Flow Control of User Plane.
258 Configuring Intra Frequency Load Balance
This section describes how to activate, verify, and deactivate the optional feature WRFD-020104
Intra Frequency Load Balance.
This section describes how to activate, verify, and deactivate the optional feature WRFD-020307
Video Telephony Fallback to Speech (AMR) for Inter-RAT HO.
272 Configuring Inter-RAT Handover Phase 2
This section describes how to activate, verify, and deactivate the optional feature WRFD-020308
Inter-RAT Handover Phase 2.
273 Configuring NACC(Network Assisted Cell Change)
This section describes how to activate, verify, and deactivate the optional feature
WRFD-02030801 NACC(Network Assisted Cell Change).
274 Configuring PS Handover between UMTS and GPRS
This section describes how to activate, verify, and deactivate the optional feature
WRFD-02030802 PS Handover between UMTS and GPRS.
275 Configuring Inter-RAT Handover Based on Service
This section describes how to activate, verify, and deactivate the optional feature WRFD-020305
Inter-RAT Handover Based on Service.
276 Configuring Inter-RAT Handover Based on Load
This section describes how to activate, verify, and deactivate the optional feature WRFD-020306
Inter-RAT Handover Based on Load.
277 Configuring Inter-RAT Redirection Based on Distance
This section describes how to activate and verify the optional feature WRFD-020401 Inter-RAT
Redirection Based on Distance.
278 Configuring 3G/2G Common Load Management
This section describes how to activate, verify, and deactivate the optional feature WRFD-020310
3G/2G Common Load Management.
279 Configuring Mobility Between UMTS and LTE Phase 1
This section describes how to activate, verify, and deactivate the optional feature WRFD-020126
Mobility Between UMTS and LTE Phase 1. For details about how to configure this feature on
the LTE side, see the related documents provided by the LTE equipment vendor. (This feature
cannot be configured using the CME. )
280 Configuring Service-Based PS Service Redirection from UMTS to LTE
This section describes how to activate, verify, and deactivate the optional feature WRFD-020129
Service-Based PS Service Redirection from UMTS to LTE.
281 Configuring Service-Based PS Handover from UMTS to LTE
This section describes how to activate, verify, and deactivate the optional feature WRFD-140218
Service-Based PS Handover from UMTS to LTE.
282 Configuring Fast CS Fallback Based on RIM
This section describes how to activate, verify, and deactivate the basic feature WRFD-140224
fast CS fallback based on RIM. For details about how to configure this feature on the LTE side,
see the related documents provided by the LTE equipment vendor.
283 Configuring Queuing and Preemption
This section describes how to activate, verify, and deactivate the optional feature WRFD-010505
Queuing and Preemption.
284 Configuring Access Class Restriction
This section describes how to activate, verify, and deactivate the optional feature WRFD-021103
Access Class Restriction.
285 Configuring Traffic Priority Mapping onto Transmission Resources
This section describes how to activate, verify, and deactivate the optional feature WRFD-050424
Traffic Priority Mapping onto Transmission Resources.
286 Configuring Differentiated Service Based on SPI Weight
This section describes how to activate, verify, and deactivate the optional feature WRFD-020806
Differentiated Service Based on SPI Weight.
287 Configuring Optimization of R99 and HSUPA Users Fairness
This section describes how to activate, verify, and deactivate the optional feature WRFD-020131
Optimization of R99 and HSUPA Users Fairness.
288 Configuring Active Queue Management (AQM)
This section describes how to activate, verify, and deactivate the optional feature WRFD-011502
Active Queue Management (AQM).
289 Configuring Quality Improvement for Subscribed Service
This section describes how to activate, verify, and deactivate the optional feature WRFD-020128
Quality Improvement for Subscribed Service.
290 Configuring TCP Accelerator
This section describes how to activate, verify, and deactivate the optional feature WRFD-020123
TCP Accelerator.
291 Configuring Rate Negotiation at Admission Control
This section describes how to activate, verify, and deactivate the optional feature WRFD-010507
Rate Negotiation at Admission Control.
292 Configuring Videophone Service Restriction
This section describes how to activate, verify, and deactivate the optional feature WRFD-020130
Videophone Service Restriction.
293 Configuring Intelligent Inter-Carrier UE Layered Management
This section describes how to activate, verify, and deactivate the optional feature WRFD-020135
Intelligent Inter-Carrier UE Layered Management.
294 Configuring Micro NodeB Self-Planning
This section describes how to activate, verify, and deactivate the optional feature WRFD-140219
Micro NodeB Self-Planning.
295 Configuring NodeB Integrated IPSec
This section describes how to activate, verify, and deactivate the optional feature WRFD-140209
NodeB Integrated IPSec.
This section describes how to activate, verify, and deactivate the optional feature WRFD-140210
NodeB PKI Support. (This feature cannot be configured using the CME. )
This section describes how to activate, verify, and deactivate the optional feature WRFD-140220
Intelligent Battery Management. (This feature cannot be configured using the CME. )
This section describes how to activate, verify, and deactivate the optional feature MRFD-221801
Multi-mode Dynamic Power Sharing (UMTS).
This section describes how to activate, verify, and deactivate the optional feature MRFD-221802
GSM and UMTS Dynamic Spectrum Sharing (UMTS). This feature enables the spectrum
resources to be dynamically shared between the GSM and UMTS networks based on their traffic
load, improving frequency utilization.
This section describes how to activate, verify, and deactivate the optional feature MRFD-221501
IP-Based Multi-Mode Co-Transmission on Base Station Side. For details about data
configurations, see section Configuration Reference > MBTS Configuration Reference
(V100R007C00) > Common Transmission in the 3900 Series Base Station Initial
Configuration Guide, or see section Common Transmission in the WCDMA RAN Feature
Documentation. The latest 3900 Series Base Station Initial Configuration Guide can be obtained
from the following path: HUAWEI Technical Support (support.huawei.com), Support >
Documentation > SingleRAN > MBTS > SingleRAN7.0.
This section describes how to activate, verify, and deactivate the optional feature MRFD-221504
TDM-Based Multi-mode Co-Transmission via Backplane on BS side (NodeB). (This feature
cannot be configured using the CME. )
This section describes how to activate, verify, and deactivate the optional feature MRFD-221601
Multi-Mode BS Common Reference Clock (NodeB). For details about data configurations, see
section Configuration Reference > MBTS Configuration Reference (V100R007C00) >
Common Clock in the 3900 Series Base Station Initial Configuration Guide, or see section
Common Clock in the WCDMA RAN Feature Documentation. The latest 3900 Series Base
Station Initial Configuration Guide can be obtained from the following path: HUAWEI
Technical Support (support.huawei.com), Support > Documentation > SingleRAN > MBTS
> SingleRAN7.0.
This section describes how to activate, verify, and deactivate the multi-mode feature
MRFD-221602 Multi-mode BS Common IPSec(UMTS).
304 Configuring 2.0MHz Central Frequency point separation between GSM and UMTS
mode(UMTS)
This section describes how to activate, verify, and deactivate the optional feature MRFD-221703
2.0MHz Central Frequency point separation between GSM and UMTS mode(UMTS).
305 Configuring Dynamic MA for GU Dynamic Spectrum Sharing (UMTS)
This section describes how to activate, verify, and deactivate the multi-mode feature
MRFD-221803 Dynamic MA for GU Dynamic Spectrum Sharing(UMTS).
306 Configuring GSM Power Control on Interface Frequency for GU Small Frequency
Gap (UMTS)
This section describes how to activate, verify, and deactivate the multi-mode feature
MRFD-221804 GSM Power Control on Interference Frequency for GU Small Frequency gap
(UMTS).
Conventions
Symbol Conventions
The symbols that may be found in this document are defined as follows.
Symbol Description
General Conventions
The general conventions that may be found in this document are defined as follows.
Convention Description
Command Conventions
The command conventions that may be found in this document are defined as follows.
Convention Description
GUI Conventions
The GUI conventions that may be found in this document are defined as follows.
Convention Description
Keyboard Operations
The keyboard operations that may be found in this document are defined as follows.
Format Description
Key Press the key. For example, press Enter and press Tab.
Key 1+Key 2 Press the keys concurrently. For example, pressing Ctrl+Alt
+A means the three keys should be pressed concurrently.
Key 1, Key 2 Press the keys in turn. For example, pressing Alt, A means
the two keys should be pressed in turn.
Mouse Operations
The mouse operations that may be found in this document are defined as follows.
Action Description
Click Select and release the primary mouse button without moving
the pointer.
Drag Press and hold the primary mouse button and move the
pointer to a certain position.
Contents
124 Configuring HSDPA H-ARQ & Scheduling (MAX C/I, RR, and PF).........................430
125 Configuring HSDPA Static Code Allocation and RNC-Controlled Dynamic Code
Allocation.......................................................................................................................................432
126 Configuring HSDPA Power Control ................................................................................434
127 Configuring HSDPA Admission Control.........................................................................437
128 Configuring Improvement of User Experience in Low Traffic Service......................440
129 Configuring HSDPA Flow Control....................................................................................442
130 Configuring HSDPA Mobility Management...................................................................445
131 Configuring HSDPA UE Category 1 to 28........................................................................447
132 Configuring DL 16QAM Modulation...............................................................................448
133 Configuring Dynamic Code Allocation Based on NodeB.............................................450
134 Configuring HSDPA Enhanced Package..........................................................................454
135 Configuring Scheduling based on EPF and GBR...........................................................456
136 Configuring HSDPA State Transition...............................................................................458
137 Configuring HSDPA DRD..................................................................................................460
138 Configuring HS-DPCCH Preamble Support...................................................................462
139 Configuring Streaming Traffic Class on HSDPA...........................................................465
140 Configuring HSDPA over Iur.............................................................................................467
141 Configuring SRB over HSDPA...........................................................................................469
142 Configuring CQI Adjustment Based on Dynamic BLER Target.................................473
143 Configuring MIMO Prime...................................................................................................475
144 Configuring Adaptive Configuration of Typical HSPA Rate......................................478
145 Configuring HSDPA Scheduling Based on UE Location..............................................480
146 Configuring Adaptive Adjustment of HSUPA Small Target Retransmissions
..........................................................................................................................................................482
147 Configuring HSPA+ Downlink 28Mbps per User..........................................................485
148 Configuring HSPA+ Downlink 21Mbps per User..........................................................487
149 Configuring Downlink Enhanced L2................................................................................489
150 Configuring HSPA+ Downlink 42Mbps per User..........................................................492
151 Configuring Downlink 64QAM.........................................................................................495
152 Configuring 2x2 MIMO........................................................................................................499
271 Configuring Video Telephony Fallback to Speech (AMR) for Inter-RAT HO.........906
272 Configuring Inter-RAT Handover Phase 2.......................................................................908
273 Configuring NACC(Network Assisted Cell Change)....................................................910
274 Configuring PS Handover between UMTS and GPRS..................................................912
275 Configuring Inter-RAT Handover Based on Service.....................................................915
276 Configuring Inter-RAT Handover Based on Load..........................................................918
277 Configuring Inter-RAT Redirection Based on Distance................................................921
278 Configuring 3G/2G Common Load Management...........................................................924
279 Configuring Mobility Between UMTS and LTE Phase 1..............................................926
280 Configuring Service-Based PS Service Redirection from UMTS to LTE...................930
281 Configuring Service-Based PS Handover from UMTS to LTE.....................................934
282 Configuring Fast CS Fallback Based on RIM..................................................................938
283 Configuring Queuing and Preemption.............................................................................941
284 Configuring Access Class Restriction ..............................................................................943
285 Configuring Traffic Priority Mapping onto Transmission Resources........................947
286 Configuring Differentiated Service Based on SPI Weight............................................949
287 Configuring Optimization of R99 and HSUPA Users Fairness...................................955
288 Configuring Active Queue Management (AQM)...........................................................959
289 Configuring Quality Improvement for Subscribed Service.........................................961
290 Configuring TCP Accelerator..............................................................................................964
291 Configuring Rate Negotiation at Admission Control....................................................966
292 Configuring Videophone Service Restriction.................................................................970
293 Configuring Intelligent Inter-Carrier UE Layered Management.................................972
294 Configuring Micro NodeB Self-Planning.........................................................................977
295 Configuring NodeB Integrated IPSec................................................................................983
296 Configuring NodeB PKI Support.....................................................................................1004
297 Configuring Intelligent Battery Management...............................................................1015
298 Configuring Multi-mode Dynamic Power Sharing (UMTS)......................................1018
299 Configuring GSM and UMTS Dynamic Spectrum Sharing (UMTS).......................1021
300 Configuring IP-Based Multi-Mode Co-Transmission on Base Station Side (NodeB)
........................................................................................................................................................1026
This chapter describes the changes in the RAN Feature Activation Guide.
05 (2012-12-31)
This is the fifth commercial release of RAN14.0.
Compared with issue 04 (2012-11-07), this issue does not include any topics.
Compared with issue 04 (2012-11-07), this issue incorporates the following changes:
Content Description
Compared with issue 04 (2012-11-07), this issue does not exclude any topics.
04 (2012-11-07)
This is the fourth commercial release of RAN14.0.
Compared with issue 03 (2012-08-30), this issue does not include any topics.
Compared with issue 03 (2012-08-30), this issue incorporates the following changes:
Content Description
Compared with issue 03 (2012-08-30), this issue does not exclude any topics.
03 (2012-08-30)
This is the third commercial release of RAN14.0.
Compared with issue 02 (2012-06-30), this issue includes the following topics:
l 138 Configuring HS-DPCCH Preamble Support
Compared with issue 02 (2012-06-30), this issue incorporates the following changes:
Content Description
Content Description
92 Configuring A-GPS Based LCS The task example and the procedure are
changed.
176 Configuring Voice Service Experience The procedure is changed, and the data
Improvement for Weak Reception UEs preparation is added.
Content Description
Compared with issue 02 (2012-06-30), this issue does not exclude any topics.
02 (2012-06-30)
This is the second commercial release of RAN14.0.
Compared with issue 01 (2012-04-26), this issue does not include any topics.
Compared with issue 01 (2012-04-26), this issue incorporates the following changes:
Content Description
Content Description
Compared with issue 01 (2012-04-26), this issue does not exclude any topics.
01 (2012-04-26)
This is the first commercial release of RAN14.0.
Compared with issue Draft B (2012-03-26), this issue includes the following new topics:
l 200 Configuring MOCN Cell Resource Demarcation
l 282 Configuring Fast CS Fallback Based on RIM
l 155 Configuring HSPA+ Downlink 84 Mbit/s per User
l 69 Configuring AMR Voice Quality Improvement Based on PLVA
l 160 Configuring HSPA+ Uplink 23 Mbit/s per User
l 260 Configuring CE Overbooking
l 294 Configuring Micro NodeB Self-Planning
Compared with issue Draft B (2012-03-26), this issue incorporates the following changes:
content Description
215 Configuring PDCP Header The step of activating the license is deleted.
Compression (RFC2507)
content Description
105 Configuring HSUPA 2ms TTI The step of enabling the single-user peak-rate
improvement algorithm of HSUPA 2 ms TTI
is added.
120 Configuring Control Channel Parallel The verification steps are modified.
Interference Cancellation (Phase 2)
Compared with issue Draft B (2012-03-26), this issue does not exclude any topics.
Draft B (2012-03-26)
This is the Draft B release of RAN14.0.
Compared with issue Draft A (2012-02-15), this issue does not include any new topics.
Compared with issue Draft A (2012-02-15), this issue incorporates the following changes:
content Description
172 Configuring Flexible HSPA+ The limit that WRFD-010704 Flexible HSPA
Technology Selection + Technology Selection cannot be used
together with WRFD-010699 DC-HSDPA
+MIMO is deleted from prerequisites, and the
configuration of DC-HSDPA and MIMO is
added.
Compared with issue Draft A (2012-02-15), this issue does not exclude any topics.
Draft A (2012-02-15)
This is the Draft A release of RAN14.0.
Compared with issue 05 (2012-01-05) of RAN13.0, this issue includes the following new topics:
l 41 Configuring CS Fallback Guarantee for LTE Emergency Calls
l 144 Configuring Adaptive Configuration of Typical HSPA Rate
l 145 Configuring HSDPA Scheduling Based on UE Location
l 146 Configuring Adaptive Adjustment of HSUPA Small Target Retransmissions
l 161 Configuring DC-HSUPA
l 176 Configuring Voice Service Experience Improvement for Weak Reception UEs
l 177 Configuring Layered Paging in URA_PCH
l 218 Configuring Iu/Iur Transmission Resource Pool in RNC
l 219 Configuring Iub Transmission Resource Pool in RNC
l 259 Configuring Dynamic Target ROT Adjustment
l 261 Configuring Intelligent Access Class Control
l 262 Configuring Dynamic Configuration of HSDPA CQI Feedback Period
l 263 Configuring Load-based Uplink Target BLER Configuration
l 264 Configuring Inter-Frequency Load Balancing Based on Configurable Load
Threshold
l 281 Configuring Service-Based PS Handover from UMTS to LTE
l 295 Configuring NodeB Integrated IPSec
l 296 Configuring NodeB PKI Support
l 297 Configuring Intelligent Battery Management
l 303 Multi-mode BS Common IPSec(UMTS)
l 305 Configuring Dynamic MA for GU Dynamic Spectrum Sharing (UMTS)
l 306 Configuring GSM Power Control on Interface Frequency for GU Small
Frequency Gap (UMTS)
Compared with issue 05 (2012-01-05) of RAN13.0, this issue incorporates the following
changes:
content Description
247 Configuring Inter Frequency Load The configuration of new function is added.
Balance
Compared with issue 05 (2012-01-05) of RAN13.0, this issue does not exclude any topics.
RANFeatures are classified into basic and optional features. Basic features are not license-
controlled and therefore do not require license activation before use. Some optional features are
license-controlled and therefore require license activation before use. If the Configuration
Method column for a basic feature in the RAN basic feature list is None, enabling this feature
does not involve any configurations. If the Configuration Method column for an optional feature
in the RAN optional feature list is None, this feature is enabled once it is activated.
Table 2-1 lists the RAN basic features. Table 2-2 lists the RAN optional features.
WRFD-05030110 F5 47 Configuring F5
This section provides an overview of the configuration on the CME. The CME is a configuration
tool on GUIs assisting you to effectively configure the data about wireless NE features. You can
reconfigure configuration parameters by using the configuration expresses provided by the CME
to activate or deactivate specified features.
Feature activation and deactivation are mainly performed on the configuration expresses on the
CME. This part introduces the operations on the configuration expresses and you need to
understand the operations before activating or deactivating features.
3.1 Introduction to Configuration Methods
This section describes how to configure the features of one or multiple NEs at a time by using
the CME.
3.2 Configuring Device Data
This section describes how to configure device data on the device panel.
3.3 Introduction to the Configuration Express for UMTS Global Parameters
This section describes the structure and provides the configuration guidance to the configuration
express for UMTS global parameters.
3.4 Introduction to the Configuration Express for Iub Interfaces
This section describes the structure and provides the configuration guidance to the configuration
express for Iub interfaces.
3.5 Introduction to the Configuration Express for Iu-CS Interfaces
This section describes the structure and provides the configuration guidance to the configuration
express for Iu-CS interfaces.
3.6 Introduction to the Configuration Express for Iu-PS Interfaces
This section describes the structure and provides the configuration guidance to the configuration
express for Iu-PS interfaces.
3.7 Introduction to the Configuration Express for Iur Interfaces
This section describes the structure and provides the configuration guidance to the configuration
express for Iur interfaces.
3.8 Introduction to the Configuration Express for Iu-BC Interfaces
This section describes the structure and provides the configuration guidance to the configuration
express for Iu-BC interfaces.
3.9 Introduction to the Configuration Express for Iu-PC Interfaces
This section describes the structure and provides the configuration guidance to the configuration
express for Iu-PC interfaces.
3.10 Introduction to the Configuration Express for the (U)Iur-g Interface
This section describes the structure and provides the configuration guidance to the configuration
express for the (U)Iur-g interface.
3.11 Introduction to the Configuration Express for Gi Interfaces
This section describes the structure and provides the configuration guidance to the configuration
express for Gi interfaces.
3.12 Introduction to the Configuration Express for UMTS Global Radio Parameters
This section describes the structure and provides the configuration guidance to the configuration
express for UMTS global radio parameters.
3.13 Introduction to the Configuration Express for UMTS Cells
This section describes the structure and provides the configuration guidance to the configuration
express for UMTS cells.
3.14 Introduction to the Configuration Express for Neighboring UMTS Cells
This section describes the structure and provides the configuration guidance to the configuration
express for neighboring UMTS cells.
3.15 Modifying RNC Parameters in Batches
This section describes how to change values of specified parameters for specified RNCs in
batches.
3.16 Modifying Logical NodeB Parameters in Batches
This section describes how to change values of specified parameters for specified logical NodeBs
in batches.
3.17 Modifying Physical NodeB Parameters in Batches
This section describes how to modify the data about multiple physical NodeBs in batches.
3.18 Modifying UMTS Cell Parameters in Batches
This section describes how to change values of specified parameters for specified UMTS cells
in batches.
3.19 Modifying RNC External Cell Parameters in Batches
This section describes how to change values of specified parameters for specified RNC external
cells in batches.
3.20 Modifying UMTS Channel Parameters in Batches
This section describes how to change values of specified parameters for specified UMTS
channels in batches.
3.21 Introduction to the Object Group Configuration
This section describes how to search for external cells in an object group and configure them.
Config Characteristics
uratio
n
Metho
d
Single Configures parameters for only one object (for example, a base station or a cell)
configu each time.
ration The CME provides configuration expresses and device panels for various types of
data to configure one object.
l The CME displays a navigation tree in the left pane and a table in the right pane.
The navigation tree shows managed objects (MOs) while the table shows the
parameters of the MOs and parameter values. After selecting an MO in the
navigation tree, you can configure its values in the table.
l The device panel is displayed on a GUI, allowing you to directly configure data
for devices such as cabinet, subrack, and board.
Batch Applies the configuration data about an object (for example, a base station or a
modific cell) to other objects.
ation NOTE
center This method is applicable to scenarios where the parameters for multiple objects need to be
configured the same.
For example, after setting the VAMOSSWITCH parameter for cell 1 to ON, you
can use the batch modification function to set the VAMOSSWITCH parameters
for other specified cells to ON at a time. By doing this, you do not need to configure
the parameters for these cells one by one.
Add l In the upper-right part of the device panel window, click Add Cabinet.
l Right-click an empty subrack on the device panel window, and choose Add
Subrack from the shortcut menu.
l Right-click the empty slots on the panels of each subrack, and choose the
required board types from the shortcut menu.
Delete l Right-click a cabinet to be deleted, and choose Delete Cabinet from the
shortcut menu.
l Right-click a subrack to be deleted, and choose Delete Subrack from the
shortcut menu.
l Right-click a board to be deleted, and choose Delete Board from the shortcut
menu.
Configuration Guidance
1. In area 1, choose The NE to be configured > UMTS > RNC in the Transport navigation
tree. The express window for configuring UMTS global parameters is displayed.
2. In area 2, select an object to be configured in the Properties navigation tree. The
configuration parameters of the object are displayed in area 3.
TIP
In area 2, you can also type the parameters to be configured on the tab pages Parameter List and
Search. This helps to quickly locate parameters.
3. In area 3, configure the data.
Configuration Guidance
1. In area 1, choose The NE to be configured > UMTS > Iub in the Transport navigation
tree. The express window for configuring Iub interfaces is displayed.
2. In area 2, select a NodeB to be configured.
3. In area 3, select an object to be configured in the navigation tree Properties. The
configuration parameters of the object are displayed in area 4.
TIP
In area 3, you can also type the parameters to be configured on the tab pages Parameter List and
Search. This helps to quickly locate parameters.
4. In area 4, configure the parameters.
The configuration express provides a window for configuring interface-level objects, as shown
in Figure 3-4.
Configuration Guidance
1. In area 1, choose The NE to be configured > UMTS > Iu-CS in the Transport navigation
tree. The express window for configuring Iu-CS interfaces is displayed.
In area 2, you can also type the parameters to be configured on the tab pages Parameter List and
Search. This helps to quickly locate parameters.
3. In area 3, configure the data.
The configuration express provides a window for configuring interface-level objects, as shown
in Figure 3-5.
Configuration Guidance
1. In area 1, choose The NE to be configured > UMTS > Iu-PS in the Transport navigation
tree. The express window for configuring Iu-PS interfaces is displayed.
2. In area 2, select an object to be configured in the Properties navigation tree. The
configuration parameters of the object are displayed in area 3.
TIP
In area 2, you can also type the parameters to be configured on the tab pages Parameter List and
Search. This helps to quickly locate parameters.
Configuration Guidance
1. In area 1, choose The NE to be configured > UMTS > Iur in the Transport navigation
tree. The express window for configuring Iur interfaces is displayed.
2. In area 2, select an object to be configured in the Properties navigation tree. The
configuration parameters of the object are displayed in area 3.
TIP
In area 2, you can also type the parameters to be configured on the tab pages Parameter List and
Search. This helps to quickly locate parameters.
3. In area 3, configure the data.
Configuration Guidance
1. In area 1, choose The NE to be configured > UMTS > Iu-BC in the Transport navigation
tree. The express window for configuring Iu-BC interfaces is displayed.
2. In area 2, select an object to be configured in the Properties navigation tree. The
configuration parameters of the object are displayed in area 3.
TIP
In area 2, you can also type the parameters to be configured on the tab pages Parameter List and
Search. This helps to quickly locate parameters.
3. In area 3, configure the data.
Configuration Guidance
1. In area 1, choose The NE to be configured > UMTS > Iu-PC in the Transport navigation
tree. The express window for configuring Iu-PC interfaces is displayed.
2. In area 2, select an object to be configured in the Properties navigation tree. The
configuration parameters of the object are displayed in area 3.
TIP
In area 2, you can also type the parameters to be configured on the tab pages Parameter List and
Search. This helps to quickly locate parameters.
3. In area 3, configure the data.
Configuration Guidance
1. In area 1, choose The NE to be configured > UMTS > Iur-g in the Transport navigation
tree. The configuration express window for configuring (U)Iur-g interfaces is displayed.
2. In area 2, select an object to be configured in the Properties navigation tree. The
configuration parameters of the object are displayed in area 3.
TIP
In area 2, you can also type the parameters to be configured on the tab pages Parameter List and
Search. This helps to quickly locate parameters.
3. In area 3, configure the data.
Configuration Guidance
1. In area 1, choose The NE to be configured > UMTS > Gi in the Transport navigation
tree. The express window for configuring Gi interfaces is displayed.
2. In area 2, select an object to be configured in the Properties navigation tree. The
configuration parameters of the object are displayed in area 3.
TIP
In area 2, you can also type the parameters to be configured on the tab pages Parameter List and
Search. This helps to quickly locate parameters.
3. In area 3, configure the data.
Configuration Guidance
1. In area 1, right-click a UMTS NE to be configured in the Main View navigation tree, and
choose UMTS Radio Global Configuration Express from the shortcut menu. The express
window for configuring UMTS global radio parameters is displayed.
2. In area 2, select an object to be configured in the Properties navigation tree. The
configuration parameters of the object are displayed in area 3.
TIP
In area 2, you can also type the parameters to be configured on the tab pages Parameter List and
Search. This helps to quickly locate parameters.
3. In area 3, configure the data.
Configuration Guidance
1. In area 1, right-click a UMTS cell in the Main View navigation tree, and choose UMTS
Cell Configuration Express from the shortcut menu. The express window for configuring
UMTS cells is displayed.
2. (Optional)In area 2, select a cell to be configured.
3. In area 3, select an object to be configured in the navigation tree Properties. The
configuration parameters of the object are displayed in area 4.
TIP
In area 3, you can also type the parameters to be configured on the tab pages Parameter List and
Search. This helps to quickly locate parameters.
4. In area 4, configure the data.
Configuration Guidance
1. In area 1, right-click a UMTS cell in the Main View navigation tree, and then choose
UMTS Neighboring Cell Configuration Express. The express window for configuring
neighboring UMTS cells is displayed.
2. (Optional)Select a source cell in area 2.
3. Select the object to be configured in the Properties navigation tree in area 3.
4. Select the corresponding Template and NE in area 4. Select one or multiple required
neighboring cells, and click Add. The information about the neighboring cell is displayed
in area 5.
5. (Optional) Right-click the neighboring cell selected in area 5, and choose Modify NCell
Relationship from the shortcut menu to modify the information about the neighboring cell.
Procedure
Step 1 In the configuration window, select a data record and click . The dialog box for selecting
objects is displayed.
Step 3 Click Next. The dialog box for selecting parameters is displayed.
The dialog box displays only names and values of the parameters that can be changed in batches. You can
change parameter values as required.
The CME uses values of selected parameters as references to change parameter values of other specified
RNCs in batches.
Step 5 Click Next. The CME starts batch modification. After modification, the CME displays the
results.
----End
Procedure
Step 1 In the configuration window, select a data record and click . The dialog box for selecting
objects is displayed.
Step 2 Click Add. Select the mode for adding NodeBs. For details, see Introduction to the Object
Selection Modes.
Step 3 Click Next. The dialog box for selecting parameters is displayed.
The dialog box displays only names and values of the parameters that can be changed in batches. You can
change parameter values as required.
The CME uses values of selected parameters as references to change parameter values of other specified
NodeBs in batches.
Step 5 Click Next. The CME starts batch modification. After modification, the CME displays the
results.
----End
Procedure
Step 1 In the Main View navigation tree in the left pane of the planned data area, right-click a UMTS
NE, and choose CM Express > UMTS Application > Physical NodeB Management > Modify
Physical NodeB Parameters in Bulk (M2000 Client Mode) or UMTS Application > Physical
NodeB Management > Modify Physical NodeB Parameters in Bulk (CME Client Mode)
from the menu bar. The Modify Physical NodeB Parameters in Bulk dialog box is displayed.
Step 2 Select an object to be modified and click Next. The data about the object for all physical NodeBs
in the planned data area is displayed in the lower part of the window. Select one or multiple
records, and click .
Step 3 Click Next, and modify the parameters value of the selected object.
Step 4 Click Finish. The CME starts to modify the parameter value of the selected object.
Step 5 After the modification is complete, click Finish to exit the wizard.
After the automatic modification is complete, the CME displays a message, indicating whether
the modification is successful. If the modification fails, you need to locate and solve the problem
based on the displayed information.
----End
Procedure
Step 1 In the configuration window, select a data record and click . The dialog box for selecting
objects is displayed.
Modify all cells under an NE in batches Select BY NE from the Select mode drop-down
list and select NEs in the NE list.
Modify specified cells under an NE in Select BY Cell from the Select mode drop-down
batches list, click Add, and select the mode for adding
cells based on site requirements. For details, see
Introduction to the Object Selection Modes.
Step 3 Click Next. The dialog box for selecting parameters is displayed.
Step 4 Select parameters to be modified in batches.
NOTE
The dialog box displays only names and values of the parameters that can be changed in batches. You can
change parameter values as required.
The CME uses values of selected parameters as references to change parameter values of other specified
cells in batches.
Step 5 Click Next. The CME starts batch modification. After modification, the CME displays the
results.
Step 6 Click Finish.
----End
Procedure
Step 1 In the configuration window, select a data record and click . The dialog box for selecting
objects is displayed.
Step 2 Select RNC external cells to be modified in batches.
Modify all RNC external cells under an Select BY NE from the Select mode drop-down
NE in batches list and select NEs in the NE list.
Modify specified RNC external cells The following uses RNC 2G external cell as an
under an NE in batches example.
Select BY GSMCELL from the Select mode
drop-down list, click Add, and select the mode for
adding RNC external cells based on site
requirements. For details, see Introduction to the
Object Selection Modes.
NOTE
l If you want to modify RNC 3G external cells, the
Select mode drop-down list displays BY
NRNCCELL.
l If you want to modify RNC LTE external cells, the
Select mode drop-down list displays By
LTECELL.
Step 3 Click Next. The dialog box for selecting parameters is displayed.
The dialog box displays only names and values of the parameters that can be changed in batches. You can
change parameter values as required.
The CME uses values of selected parameters as references to change parameter values of other specified
RNC external cells in batches.
Step 5 Click Next. The CME starts batch modification. After modification, the CME displays the
results.
----End
Procedure
Step 1 In the configuration window, select a data record and click . The dialog box for selecting
objects is displayed.
Modify all cells under an NE in batches Select BY NE from the Select mode drop-down
list and select NEs in the NE list.
Modify specified cells under an NE in Select BY Cell from the Select mode drop-down
batches list, click Add, and select the mode for adding
cells based on site requirements. For details, see
Introduction to the Object Selection Modes.
Step 3 Click Next. The dialog box for selecting parameters is displayed.
The dialog box displays only names and values of the parameters that can be changed in batches. You can
change parameter values as required.
The CME uses values of selected parameters as references to change parameter values of other specified
cells in batches.
Step 5 Click Next. The CME starts batch modification. After modification, the CME displays the
results.
----End
Configuration Guidance
1. In area 1, select the BSC to be configured in the Main View navigation tree.
2. In area 2, select the external cell to be configured in the Object Group navigation tree.
TIP
In area 2, you can also type the parameters to be set on the Search tab page. This helps quickly locate
parameters.
3. In area 3, configure the data.
In the case of certain UMTS features, a license control item is defined for each feature. The
license control item of a feature must be activated before the configuration and use of the feature.
The license control items related to the RNC can be activated on the M2000 or RNC LMT,
whereas those related to the NodeB can be activated only on the M2000.
Prerequisites
l The LMT is started and you have logged in to the BSC6900.
l The BSC6900 is in service.
Procedure
Step 1 Run the BSC6900 MML command LST ESN and record the Equipment Serial Number (ESN)
of the BSC.
Step 2 Run the BSC6900 MML command DLD LICENSE to download the license file from the FTP
server to the \ftp\license directory of the main area directory of the OMU.
Step 3 Run the LST LICENSE command and enter the filename of the license to be activated to query
the file information.
If... Then...
The file information does not comply with the Exit the task and contact Huawei.
information of the file that you apply for,
Step 4 Run the LST CFGMODE command to query the BSC6900 configuration status. If the
BSC6900 is ineffective, run the SET CFGDATAEFFECTIVE command to switch it to the
effective state.
Step 6 If the primary operator and secondary operators exist, run the SET LICENSE command to
active the license for the primary operator first and then for secondary operators. If multiple
secondary operators exist, run the SET LICENSE command repeatedly.
Step 7 Run the BSC6900 MML command CMP LICENSE to check whether the running license on
the host is consistent with that on the OMU.
If... Then...
If the running license on the host is consistent with that End the task or go to Step 8.
on the OMU
If the running license on the host is inconsistent with End the task and contact Huawei.
that on the OMU
Step 8 In the case of high traffic, run the SET LICENSECTRL command to enable the license control
function of the BSC6900 to enter the grace protection period.
----End
Prerequisites
You have uploaded a valid NodeB license file to the M2000 server.
Procedure
Step 1 Choose License > NE License Management > NodeB License Management. The NodeB
License Management window is displayed.
Step 2 From the navigation tree in the left pane of the NodeB License Management window, select
an RNC node whose NodeB license file is already uploaded to the M2000 server.
Step 3 Right-click a license, and then choose License Distributed to Operator from the shortcut menu.
Step 4 In the License Distributed to Operator window, set available functions and resources for each
telecom operator, and then click OK.
----End
Prerequisites
You have uploaded a valid NodeB license file to the M2000 server.
Procedure
Step 1 Choose License > NE License Management > NodeB License Management. The NodeB
License Management window is displayed.
Step 2 From the navigation tree in the left pane of the NodeB License Management window, select
an RNC node whose NodeB license file is already uploaded to the M2000 server.
Step 3 Optional: In the lower part of the license information area, click the tab of a telecom operator.
If a RAN is shared by multiple telecom operators, you can allocate a NodeB license to them by
referring to 4.2 Allocating a license to Telecom Operators.
The license allocation information about all the NodeBs related to the telecom operator is
displayed in a list.
Step 4 Double-click a NodeB to which you need to allocate the license, or right-click the NodeB and
choose Modify from the shortcut menu. Then, set available resources and functions for the
NodeB.
NOTE
l You can set a function control item to either 0 or 1. 0 indicates that the function is not enabled while
1 indicates that the function is enabled.
l You can hold down Ctrl or Shift to select multiple NodeBs at a time. Right-click the selected NodeBs,
and then choose Modify from the shortcut menu to set a control item value to all the selected NodeBs.
l If a control item is unavailable in the Modify dialog box, it indicates that the control item is not
supported by NodeBs. To view the values indicating that the control item is not supported by NodeBs,
click the status description on the right in the Modify dialog box. For descriptions of the values, see
Parameter Description in the dialog box.
l When setting a certain control item, you can click Clear to clear the preset values in the column of the
control item.
l You can click Settings in the Modify dialog box to add or delete one or multiple control items to be
set.
----End
This section describes how to activate, verify, and deactivate the basic feature WRFD-010510
3.4/6.8/13.6/27.2Kbps RRC Connection and Radio Access Bearer Establishment and Release.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
Context
This feature enables RRC connection establishment and release and RAB assignment for
services of different rates, so as to meet different QoS requirements. This feature is fundamental
to service provision.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET URRCESTCAUSE (CME single
configuration: UMTS Radio Global Configuration Express > Channel Type and
Rate of RRC Setup Cause Configuration > RRC Connection Establish Channel
Type And Bit Rate; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to set the channel type and bit rate corresponding to a specific
RRC connection establishment cause.
NOTE
Do not set Channel type for RRC establishment to FACH. Set Switch for RRC established
on E_FACH to OFF.
l Verification Procedure
1. Start Iub interface tracing on the BSC6900 LMT, as shown in Figure 5-1
2. Establish a service on the UE. Among the traced Iub data, view the dCH-ID in the
DCH-Specific-FDD-Item IE in the NBAP_RL_SETUP_REQ message. The result
shows that the ID of the transport channel that carries signaling is 32.
3. View the transmissionTimeInterval and nrOfTransportBlocks IEs in the ul-
TransportFormatSet IE associated with the DCH whose dCH-ID value is 32.
If the value of transmissionTimeInterval is 40, you can infer that an RRC
connection is established for a 3.4 kbit/s service.
If the value of transmissionTimeInterval is 20, you can infer that an RRC
connection is established for a 6.8 kbit/s service.
If the value of transmissionTimeInterval is 10 and the maximum value of
nrOfTransportBlocks is 1, you can infer that an RRC connection is established
for a 13.6 kbit/s service.
If the value of transmissionTimeInterval is 10 and the maximum value of
nrOfTransportBlocks is 2, you can infer that an RRC connection is established
for a 27.2 kbit/s service.
4. Release the service on the UE, and perform Uu interface tracing. If you find an
RRC_RRC_CONN_REL_CMP message in the traced data, you can infer that the
RRC connection is released.
l Deactivation Procedure
1. This feature does not need to be deactivated.
----End
Example
//Activating 3.4/6.8/13.6/27.2Kbps RRC Connection and Radio Access Bearer
Establishment and Release.
//set the channel type and bit rate corresponding to a specific RRC
connection establishment cause
This section describes how to activate, verify, and deactivate the basic feature WRFD-010501
Conversational QoS Class.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
l Others
The UE and the CN support the conversational class.
Context
Based on QoS requirements, 3GPP defines four traffic classes: conversational, streaming,
interactive, and background.
They differ in their sensitivity to delay. The conversational class is highly sensitive to the delay
and therefore has a high requirement on real-time transmission. The conversational class has the
following fundamental characteristics:
l Preservation of the time relationships between information entities in a stream and
limitation of the transmission delay and delay jitter within an acceptable range.
l Conversational pattern (stringent requirement on the delay).
Conversational services are applicable in both the CS and PS domains. Most typical applications
of the conversational class are voice services and videophone services in the CS domain and
VoIP services in the PS domain.
Huawei RAN supports the following basic types of conversational services:
l CS AMR speech services at the rates of 12.2 kbit/s, 10.2 kbit/s, 7.95 kbit/s, 7.4 kbit/s, 6.7
kbit/s, 5.9 kbit/s, 5.15 kbit/s, and 4.75 kbit/s
l CS transparent data services (conversational class) at the rates of 64 kbit/s, 56 kbit/s, 32
kbit/s, and 28.8 kbit/s
l PS bidirectional symmetric voice services at the rates of 64 kbit/s, 42.8 kbit/s, 32 kbit/s, 16
kbit/s, and 8 kbit/s
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UFRCCHLTYPEPARA (CME single
configuration: UMTS Radio Global Configuration Express > Basic Resource
Control Parameter Configuration > Channel Type Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches). In this step, set
CS voice channel type and VOIP channel type to DCH(UL_DCH,DL_DCH).
l Verification Procedure
1. Initiate Iub interface tracing on the BSC6900 LMT, as shown in Figure 6-1.
2. Establish a conversational service on the UE. Check the DPC (that is, the source) of
the RANAP_RAB_ASSIGNMENT_REQ message among the traced Iu data to
determine whether the service is a CS service or PS service.
3. View the trafficClass IE in the rRB-Parameters IE of the
RANAP_RAB_ASSIGNMENT_REQ message to verify that the traffic class is
conversational.
4. View the maxBitrate and rAB-AsymmetryIndicator IEs in the
RANAP_RAB_ASSIGNMENT_REQ message.
If the value of the rAB-AsymmetryIndicator IE is Asymmetric bidirectional,
then the maxBitrate IE contains two values. The first value indicates the downlink
rate of the conversational service, and the second indicates the uplink rate of the
service. That is, the uplink and downlink transmission uses asymmetric rates.
If the value of the rAB-AsymmetryIndicator IE is Symmetric bidirectional,
then the maxBitrate IE contains one value, which indicates the rate applicable in
both the uplink and the downlink. That is, the uplink and downlink transmission
uses symmetric rates.
If the value of the rAB-AsymmetryIndicator IE is Asymmetric Uni directional
downlink, then the maxBitrate IE contains one value, which indicates the
downlink rate of the conversational service. In this case, the uplink rate of the
service is 0.
If the value of the rAB-AsymmetryIndicator IE is Asymmetric Uni directional
Uplink, then the maxBitrate IE contains one value, which indicates the uplink
rate of the conversational service. In this case, the downlink rate of the service is
0.
5. View the guaranteedBitRate (the guaranteed bit rate of the conversational service)
and rAB-AsymmetryIndicator IEs in the RANAP_RAB_ASSIGNMENT_REQ
message by following the same rules as those for viewing maxBitrate.
l Deactivation Procedure
1. This feature does not need to be deactivated.
----End
Example
//Activating conversational QoS class
SET UFRCCHLTYPEPARA: CSVoiceChlType=DCH, VoipChlType=DCH;
This section describes how to activate, verify, and deactivate the basic feature WRFD-010502
Streaming QoS Class.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
l Others
The UE and CN support streaming services.
Context
Based on QoS requirements, there are four traffic classes: conversational, streaming, interactive,
and background.
QoS indicates the sensitivity of services to the delay. The streaming class is a relatively recent
development in data communications, which raises a number of new requirements in both
telecommunication and data communication systems. The transmission of streaming services
must follow the time sequence of information entities . The streaming class has the following
features:
l The time sequence of information entities in a stream is not changed.
l Streaming services are applicable in both the CS and PS domains. The most typical
applications of the streaming class are fax services in the CS domain and streaming video
services in the PS domain.
Streaming services are real-time services, such as audio and video programs. They are
transmitted in only one direction and serve individual users.
Procedure
l Activation Procedure
In the tests on 384 kbit/s streaming services, the settings of the thresholds cannot ensure that
the services are set up on R99 services. In this case, you can disable the HSDPA and HSUPA
capabilities of the cell to enable the streaming services to be set up on R99 channels.
2. Optional: Run the BSC6900 MML command DEA UCELLHSDPA (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
HSDPA Parameters. Set ACTSTATUS to Deactivated; CME batch modification
center: No supported) to disable the HSDPA capability of the cell.
3. Optional: Run the BSC6900 MML command DEA UCELLHSUPA (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters >
Configuration of HSUPA in Cell. Set Cell HSUPA state to Deactivated; CME batch
modification center: No supported) to disable the HSUPA capability of the cell.
l Verification Procedure
1. Start Iu interface tracing on the BSC6900 LMT, as shown in Figure 7-1
2. Use a UE to set up a streaming service. Check the DPC (that is, the source) of the
RANAP_RAB_ASSIGNMENT_REQ message among the traced Iu data to
determine whether the service is a CS service or PS service.
3. Check the RANAP_RAB_ASSIGNMENT_REQ message and check that the value
of the trafficClass information element (IE) in rRB-Parameters is streaming.
4. View the maxBitrate and rAB-AsymmetryIndicator IEs in the
RANAP_RAB_ASSIGNMENT_REQ message.
Expected result:
If the value of the rAB-AsymmetryIndicator IE is Asymmetric bidirectional,
the maxBitrate IE contains two values. The first value indicates the downlink rate
of the streaming service, and the second indicates the uplink rate of the service.
Example
//Activating Streaming Class QoS
SET UFRCCHLTYPEPARA: DlStrThsOnHsdpa=D384, UlStrThsOnHsupa=D384;
DEA UCELLHSDPA: CellId=1;
DEA UCELLHSUPA: CellId=1;
This section describes how to activate, verify, and deactivate the basic feature WRFD-010503
Interactive QoS Class.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
l Others
The UE and CN support interactive services.
Context
Based on QoS requirements, there are four traffic classes: conversational, streaming, interactive,
and background. QoS indicates the sensitivity of services to the delay.
The interactive class is a typical data communication solution. It is characterized by the request/
response pattern of end users. For example, a person or an entity at the destination sends a data
request to a remote server and expects a response message within a specific time. In this situation,
the Round Trip Time (RTT) is one of the key attributes of the interactive class. Another
characteristic is that the packets should be transparently transferred at a low Bit Error Rate
(BER). In summary, the interactive class has the following fundamental characteristics: request/
response pattern and preservation of the payload.
Interactive services are applicable in the PS domain and not applicable in the CS domain. The
most typical application of the interactive class is web browsing.
Huawei RAN supports the following types of interactive services: PS bidirectional symmetric
or asymmetric interactive services at the rates of 384 kbit/s, 285 kbit/s, 144 kbit/s, 128 kbit/s,
64 kbit/s, 32 kbit/s, 16 kbit/s, and 8 kbit/s.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UFRCCHLTYPEPARA (CME single
configuration: UMTS Radio Global Configuration Express > Basic Resource
Control Parameter Configuration > Channel Type Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches) to set the
HSDPA/HSUPA rate threshold for interactive services. If the assigned rate of an
interactive service is lower than this threshold, the interactive service is set up on R99
channels.
l Verification Procedure
1. Start Iu interface tracing on the BSC6900 LMT, as shown in Figure 8-1
----End
Example
//Activating Interactive QoS Class
SET UFRCCHLTYPEPARA: DlBeTraffThsOnHsdpa=D13900,
UlBeTraffThsOnHsupa=D5440;
This section describes how to activate, verify, and deactivate the basic feature WRFD-010504
Background QoS Class.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
l Others
The UE and CN support this feature.
Context
Based on QoS requirements, there are four traffic classes: conversational, streaming, interactive,
and background.
QoS indicates the sensitivity of services to the delay. A typical type of background service is
data services. One of the characteristics of the background class is that the destination does not
expect data within a specific time, and therefore the background class is delay-insensitive.
Another characteristic is that the packets should be transparently transferred at a low Bit Error
Rate (BER).
In summary, the background class has the following fundamental characteristics: destination not
expecting data within a specific time and preservation of the payload.
Background services are applicable in the PS domain and not applicable in the CS domain. The
most typical applications of the background class are download and emails.
Huawei RAN supports the following types of background services: PS bidirectional symmetric
or asymmetric background services at the rates of 384 kbit/s, 256 kbit/s, 144 kbit/s, 128 kbit/s,
64 kbit/s, 32 kbit/s, 16 kbit/s, and 8 kbit/s.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UFRCCHLTYPEPARA (CME single
configuration: UMTS Radio Global Configuration Express > Basic Resource
Control Parameter Configuration > Channel Type Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches) to set the
HSDPA/HSUPA rate threshold for background services. If the assigned rate of a
background service is lower than this threshold, the background service is set up on
R99 channels.
l Verification Procedure
1. Start Iu interface tracing on the BSC6900 LMT, as shown in Figure 9-1
----End
Example
//Activating Background QoS Class
SET UFRCCHLTYPEPARA: DlBeTraffThsOnHsdpa=D13900,
UlBeTraffThsOnHsupa=D5440;
This section describes how to activate, verify, and deactivate the basic feature WRFD-021104
Emergency Call.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
Context
This feature grants higher priority to emergency calls so that they are preferentially processed,
compared to normal calls.
CAUTION
If the license of the AMR-WB service is not activated on a RNC, ensure that AMR-WB is not
enabled for this RNC on the CS core network side. Otherwise, both the AMR-NB services and
emergency calls cannot be set up for the UE supporting AMR-WB.
Procedure
l Activation Procedure
This feature need not be activated.
l Verification Procedure
1. Use a UE to initiate an emergency call.. The emergency call is successfully established.
l Deactivation Procedure
This feature need not be deactivated.
----End
This section describes how to activate, verify, and deactivate the basic feature WRFD-010506
RAB Quality of Service Renegotiation over Iu Interface.
Prerequisites
l Dependencies on Hardware
The NEs in the core network must support selective configuration of the maximum bit
rate (MBR) and guaranteed bit rate (GBR).
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
Context
This feature enables the BSC6900 to initiate Iu renegotiation on the MBR and GBR of PS real-
time services to reduce the rate of real-time services.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command MOD UCELLALGOSWITCH (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Algorithm Switches; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches) to enable the cell-level LDR algorithm. In this step, set Cell
LDC algorithm switch to UL_UU_LDR(Uplink UU LDR Algorithm),
DL_UU_LDR(Downlink UU LDR Algorithm), and CELL_CREDIT_LDR
(Credit LDR Algorithm).
2. Run the BSC6900 MML command MOD UNODEBALGOPARA (CME single
configuration: NodeB Configuration Express > IUB_RNC > NodeB Basic
Information > NodeB Algorithm Parameters; CME batch modification center: 3.16
Modifying Logical NodeB Parameters in Batches) to enable the NodeB-level LDR
algorithm. In this step, set NodeB LDC algorithm switch to IUB_LDR(IUB LDR
Example
/*Activating RAB Quality of Service Renegotiation over Iu Interface*/
This section describes how to activate, verify, and deactivate the basic feature MRFD-210604
2-Way Antenna Receive Diversity.
Prerequisites
l Dependencies on Hardware
In receive diversity mode, the NodeB should provide sufficient RF channels and
demodulation resources to meet the requirements for the number of antenna diversities.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
Context
The 2-Antenna Receive Diversity is an effective approach of reducing signal attenuation by
using two antennas to receive a signal at the reception end, where two received signals are
combined after certain processing.
Procedure
l Activation Procedure
1. Run the NodeB MML command ADD SEC (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Radio Layer > Sector; CME batch
modification center: not supported). In this step, set Antenna Magnitude to 2.
l Verification Procedure
1. Run the NodeB MML command LST SEC to query the value of Antenna
Magnitude.
Expected result: Antenna Magnitude is 2.
l Deactivation Procedure
This feature does not need to be deactivated.
----End
Example
//Activation procedure
ADD SEC: STN=1, SECN=0, SECT=REMOTE_SECTOR, ANTM=2, DIVM=COMMON_MODE,
ANT1SRN=60, ANT1N=R0A, ANT2SRN=60, ANT2N=R0B;
//Verification procedure
LST SEC: STN=1, SECN=0;
This section describes how to activate, verify, and deactivate the basic feature WRFD-010205
Cell Digital Combination and Split.
Prerequisites
l Dependencies on Hardware
Only DBS3800/DBS3900 supports this feature, RRU3801c cannot support this feature.
Each RRU is configured with only one RX antenna.
It is not recommended that distributed sectors and non-distributed sectors are configured
on an RRU chain.
If distributed sectors are configured, one CPRI port supports a maximum of four
cascaded RRUs, a maximum of four RRUs share one cell, and a maximum of three
distributed cells are supported.
One BBU supports combination of uplink digital signals on only one CPRI port. A
maximum of four RRUs share one cell.
In consideration of delay requirements, the remote distance of fiber optic cables for the
RRUs in a cell and with the same coverage should be smaller than four kilometers.
RF modules, RRU3828 and RRU3829 can only support a maximum of four carriers
when they are implemented for Cell Digital Combination and Split.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
Context
The feature enables multiple sectors to use the resources in the same cell, which improves system
spectrum efficiency and resource utilization. Compared with the analog combination and split,
the digital combination and split can provide higher capacity and wider coverage without
bringing additional noises or signal losses. Cell coverage can be adjusted simply through
software to adapt to actual traffic distribution and changes, which improves CE resource
utilization and operation benefits.
Procedure
l Activation Procedure
1. Run the NodeB MML command ADD RRUCHAIN (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Device Panel > Right click
TOPO > Add RXU Chain; CME batch modification center: not supported) to add
an RRU chain. In this step, set Topo Type to CHAIN.
2. Run the NodeB MML command ADD RRU (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Device Panel > TOPO > Right click RXU
CHAIN > Add RXU Board; CME batch modification center: not supported) to add
an RRU. In this step, set a group of RRUs in consecutive numbering to the RRUs to
be used by the distributed sector.
3. Run the NodeB MML command ADD SEC (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Radio Layer > Sector; CME batch
modification center: not supported) to add a sector. In this step, set Sector Type to
DIST_SECTOR(DIST_SECTOR).
4. Run the NodeB MML command ADD LOCELL (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Radio Layer > xx Sector > Locell; CME
batch modification center: 3.17 Modifying Physical NodeB Parameters in
Batches) to add a local cell. In this step, set Sector Type to DIST_SECTOR
(DIST_SECTOR).
l Verification Procedure
1. Run the NodeB MML command LST SEC. In this step, check that Sector Type is
set to DIST_SECTOR(DIST_SECTOR).
2. Run the NodeB MML command LST LOCELL. In this step, check that Sector
Type is set to DIST_SECTOR(DIST_SECTOR).
l Deactivation Procedure
This feature does not need to be deactivated.
----End
Example
1. NodeB V200R014
//Activation procedure
ADD RRUCHAIN: RCN=0, TT=CHAIN, BM=COLD, HSN=2, HPN=0;
ADD RRU: CN=0, SRN=60, SN=0, TP=TRUNK, RCN=0, PS=0, RT=MRRU, RS=UO;
ADD RRU: CN=0, SRN=61, SN=1, TP=TRUNK, RCN=0, PS=1, RT=MRRU, RS=UO;
ADD SEC: STN=0, SECN=1, SECT=DIST_SECTOR, SRNB=60, SRNE=61;
ADD LOCELL: LOCELL=100, STN=0, SECN=1, SECT=DIST_SECTOR,
RRUMODE=SYNC, ULFREQ=9610, DLFREQ=10560, HISPM=FALSE;
//Verification procedure
LST SEC: STN=0, SECN=1;
LST LOCELL: MODE=LOCALCELL, LOCELL=100;
2. NodeB V100R014
//Activation procedure
ADD RRUCHAIN: RCN=0, TT=CHAIN, HSN=0, HPN=0;
ADD RRU: CN=0, SRN=60, TP=TRUNK, RCN=0, PS=0, RT=MRRU;
ADD RRU: CN=0, SRN=61, TP=TRUNK, RCN=0, PS=0, RT=MRRU;
ADD SEC: STN=0, SECN=1, SECT=DIST_SECTOR, SRNB=60, SRNE=61;
ADD LOCELL: LOCELL=100, STN=0, SECN=1, SECT=DIST_SECTOR,
BBPOOLTYPE=GEN_POOL, RRUMODE=SYNC, ULFREQ=9610, DLFREQ=10560,
HISPM=FALSE;
//Verification procedure
LST SEC: STN=0, SECN=1;
LST LOCELL: MODE=LOCALCELL, LOCELL=100;
This section describes how to activate, verify, and deactivate the basic feature WRFD-010202
UE State in Connected Mode (CELL_DCH, CELL_PCH, URA_PCH, CELL_FACH).
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
l Other Prerequisites
The Iu-PS activity factor is already modified.
The Iu-PS activity factor can be modified by running the ADD TRMFACTOR (CME
single configuration: UMTS Global Configuration Express > Transmission
Resources Configuration > Factor Table; CME batch modification center: not
supported) and MOD ADJMAP (CME single configuration: IUPS Configuration
Express > IP Transport > Adjacent Node Mapping; CME batch modification center:
not supported) commands. The recommended value of the Iu-PS activity factor is 10%.
NOTE
If there are excessive users in the CELL_PCH or URA_PCH state, a large amount of bandwidth
on the Iu-PS interface is consumed though such users do not have data to transmit.
Adjusting the Iu-PS activity factor can prevent PS service admission failures due to the increase
in the number of UEs in the CELL_PCH or URA_PCH state.
The Fast Dormancy procedure of the UE must comply with 3GPP TS 25.331 CR3483.
UEs must support associated states.
Context
Huawei RAN supports four states of UEs in connected mode: CELL_DCH, CELL_PCH,
URA_PCH, and CELL_FACH. This feature helps save radio resources efficiently.
Procedure
l Activation Procedure
A UE can directly enter the CELL_FACH or CELL_DCH state. It can enter the CELL_PCH
or URA_PCH state only through state transition from CELL_FACH or CELL_DCH. The
settings of state transition are as follows:
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, select the
DRA_PS_BE_STATE_TRANS_SWITCH check box under the parameter
Dynamic Resource Allocation Switch.
2. Optional: Run the BSC6900 MML command SET UCORRMALGOSWITCH
(CME single configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, select the DRA_F2U_SWITCH check box
under the parameter Dynamic Resource Allocation Switch to enable state transition
from CELL_FACH to URA_PCH directly.
3. Run the BSC6900 MML command SET UUESTATETRANSTIMER (CME single
configuration: UMTS Radio Global Configuration Express > UE State Transition
Parameter Configuration > RNC StateTrans Timer Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches). In this step, set
BE FACH or E_FACH to PCH Transition Timer and Cell Reselection Timer to
appropriate values.
4. Run the BSC6900 MML command SET UUESTATETRANS (CME single
configuration: UMTS Radio Global Configuration Express > UE State Transition
Parameter Configuration > UE State Translating Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches). In this step, set
Cell Reselection Counter Threshold to an appropriate value.
NOTE
l This feature involves the parameter settings of state transition from CELL_FACH or CELL_DCH to
CELL_PCH or URA_PCH. For the parameter settings of other types of state transition, see 17
Configuring Dynamic Channel Configuration Control.
l For the parameter settings related to fast dormancy, see 175 Configuring Enhanced Fast
Dormancy.
l Verification Procedure
This feature cannot be verified separately. The state of a UE changes when it requests
different services. This is referred to as state transition. For details, see 17 Configuring
Dynamic Channel Configuration Control.
l Deactivation Procedure
This feature does not need to be deactivated.
----End
Example
//Activating UE State in Connected Mode (CELL_DCH, CELL_PCH, URA_PCH,
CELL_FACH)
//Enabling status transition (CELL_FACH/CELL_PCH/URA_PCH)
SET UCORRMALGOSWITCH:
DraSwitch=DRA_PS_BE_STATE_TRANS_SWITCH-1&DRA_F2U_SWITCH-1;
//(Optional) Enabling state transition from CELL_FACH to URA_PCH directly
SET UUESTATETRANSTIMER: BeF2PStateTransTimer=65535,
CellReSelectTimer=180;
//Setting the parameters related to this feature
SET UUESTATETRANS: CellReSelectCounter=9;
This section describes how to activate, verify, and deactivate the basic feature WRFD-010301
Paging UE in Idle, CELL_PCH, URA_PCH State (Type 1).
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
Context
In paging type 1, the UTRAN sends a paging message to the UE in idle mode, CELL_PCH state,
or URA_PCH state through the paging control channel (PCCH).
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) with Dynamic Resource Allocation Switch set to
DRA_HSDPA_STATE_TRANS_SWITCH,
DRA_HSUPA_STATE_TRANS_SWITCH and
DRA_PS_BE_STATE_TRANS_SWITCH.
2. Run the BSC6900 MML command SET URRCTRLSWITCH (CME single
configuration: UMTS Radio Global Configuration Express > Process Switch
Configuration > Process Switch; CME batch modification center: 3.15 Modifying
RNC Parameters in Batches) to set the parameter Reserved parameter 1 to
RSVDBIT1_BIT21 (Reserved Parameter 1 Bit 21).
l After this feature is activated, number of UEs in CELL_PCH or URA_PCH state will increase
sharply. These UEs consume a large number of Iu-PS resources although there is no service data
transmission.
l You can adjust the Iu-PS activation factor to avoid the PS admission failure due to increasing
number of UEs in CELL_PCH or URA_PCH state.
l Verification Procedure (Paging a UE in Idle Mode)
1. On the BSC6900 LMT, click Trace > UMTS Services, and then double-click Uu
Interface Trace. The Uu Interface Trace dialog box is displayed.
2. Set parameters in the areas Cell Config, Uu Message Type, Trace Mode and Save
File. Then, click Submit.
3. Power on UE1 and UE2, and camp on CELL1. Use UE2 to call UE1. The
RRC_PAGING_TYPE1 message should be displayed on the Trace Data tab page.
l Commissioning Procedure (Paging a UE in CELL_PCH State)
1. On the BSC6900 LMT, click Trace > UMTS Services, and then double-click Uu
Interface Trace. The Uu Interface Trace dialog box is displayed.
2. On the HLR, set the PS service type to background or interactive.
3. Establish an R99 PS service on UE1. The RRC_RB_SETUP message should be
displayed in trace data, and the value of the rrc-stateindicator IE should be
CELL_DCH.
4. Do not send any data from UE1 for 30 seconds. Then, the network side should perform
UE1 transition to CELL_FACH state through the RRC_RB_RECFG message, and
the value of rrc-stateindicator IE should be CELL_FACH.
5. Do not send any data from UE1 for another while. Then, the network side should
perform UE1 transition to CELL_PCH state through the RRC_RB_RECFG message,
and the value of rrc-stateindicator IE should be CELL_PCH.
6. Use UE2 to call UE1. The RRC_PAGING_TYPE1 message should be displayed.
l Verification Procedure (Paging a UE in URA_PCH)
1. On the BSC6900 LMT, click Trace > UMTS Services, and then double-click Uu
Interface Trace. The Uu Interface Trace dialog box is displayed.
NOTE
For details about how to enable UE transition to CELL_PCH or URA_PCH state, see 14
Configuring UE State in Connected Mode (CELL_DCH, CELL_PCH, URA_PCH,
CELL_FACH).
l Deactivation Procedure
1. Run the BSC6900 MML command SET URRCTRLSWITCH (CME single
configuration: UMTS Radio Global Configuration Express > Process Switch
Configuration > Process Switch; CME batch modification center: 3.15 Modifying
RNC Parameters in Batches). In this step, deselect RSVDBIT1_BIT21 (Reserved
Parameter 1 Bit 21) from the Reserved parameter 1 drop-down list box.
2. Run the BSC6900 MML command SET UUESTATETRANSTIMER (CME single
configuration: UMTS Radio Global Configuration Express > UE State Transition
Parameter Configuration > RNC StateTrans Timer Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches) to set BE FACH
or E_FACH to PCH Transition Timer to 65535. When this parameter is set to
65535, the FACH-to-PCH state transition is disabled.
3. Run the BSC6900 MML command SET UPSINACTTIMER (CME single
configuration: UMTS Radio Global Configuration Express > PS Permanent
Online Detection Timer Configuration > PS User Inactive Detecting Timer; CME
batch modification center: 3.15 Modifying RNC Parameters in Batches) to set
Interactive service T1and set Background service T1 to 20.
----End
Example
// Activation Procedure
// Deactivation Procedure
This section describes how to activate, verify, and deactivate the basic feature WRFD-010302
Paging UE in CELL_FACH, CELL_DCH State (Type 2).
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
Context
In paging type 2, the UTRAN sends a paging message to the UE in CELL_FACH or CELL_DCH
state through the DCH or FACH.
Procedure
l Activation Procedure
1. (Optional) Run the BSC6900 MML command SET UCORRMALGOSWITCH
(CME single configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to turn on the RNC-oriented PS BE service state transition
switch.
2. Run the BSC6900 MML command SET UUESTATETRANSTIMER (CME single
configuration: UMTS Radio Global Configuration Express > UE State Transition
Parameter Configuration > RNC StateTrans Timer Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches) to set the
parameter BE DCH to FACH Transition Timer[s] to 30s.
3. Run the BSC6900 MML command SET UPSINACTTIMER (CME single
configuration: UMTS Radio Global Configuration Express > PS Permanent
Online Detection Timer Configuration > PS User Inactive Detecting Timer; CME
batch modification center: 3.15 Modifying RNC Parameters in Batches) to set
inactivity detection timers for PS services.
l Verification Procedure (Paging a UE in CELL_DCH State)
1. On the BSC6900 LMT, click Trace > UMTS Services, and then double-click Uu
Interface Trace. The Uu Interface Trace dialog box is displayed.
2. Set parameters in the areas Cell Config, Uu Message Type, Trace Mode and Save
File. Then, click Submit.
3. Establish an R99 PS service on UE1. The RRC_RB_SETUP message should be
displayed in trace data, and the value of the rrc-stateindicator IE should be
CELL_DCH.
4. Use UE2 to call UE1. The RRC_PAGING_TYPE2 message should be displayed.
l Verification Procedure (Paging a UE in CELL_FACH State)
1. On the BSC6900 LMT, click Trace > UMTS Services, and then double-click Uu
Interface Trace. The Uu Interface Trace dialog box is displayed.
2. Set parameters in the areas Cell Config, Uu Message Type, and Save File, and then
click Submit. The Trace Data tab page is displayed.
3. On the HLR, set the PS service type to background or interactive.
4. Establish an R99 PS service on UE1. The RRC_RB_SETUP message should be
displayed in trace data, and the value of the rrc-stateindicator IE should be
CELL_DCH.
5. Do not send any data from UE1 for 30 seconds. Then, you can view that the network
side performs UE transition to CELL_FACH state through the RRC_RB_RECFG
message. The value of rrc-stateindicator IE should be CELL_FACH.
6. Use UE2 to call UE1. The RRC_PAGING_TYPE2 message should be displayed.
l Deactivation Procedure
1. This feature does not need to be deactivated.
----End
Example
//Activating paging type 2
SET UCORRMALGOSWITCH: DraSwitch=DRA_PS_BE_STATE_TRANS_SWITCH-1;
SET UUESTATETRANSTIMER: BeD2FStateTransTimer=30;
SET UPSINACTTIMER: PsInactTmrForInt=1440, ProtectTmrForInt=20,
PsInactTmrForBac=1440, ProtectTmrForBac=20;
This section describes how to activate, verify, and deactivate the basic feature WRFD-021101
Dynamic Channel Configuration Control (DCCC). (This feature cannot be configured using the
CME. )
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
Context
This feature allows dynamic rate adjustment and UE state transition triggered by various reasons.
This improves the quality of services and increases resource utilization.
Procedure
l Activating DCCC
1. To activate the DCCC algorithm, perform the following steps:
Run the BSC6900 MML command SET UCORRMALGOSWITCH. In this step,
set Dynamic Resource Allocation Switch to DRA_DCCC_SWITCH.
2. To activate traffic-based BE service rate adjustment, perform the following steps:
a. Run the BSC6900 MML command MOD UTYPRABDCCCMC to set the
following event 4A and 4B parameters:
Direction
Event4AThd
Event4BThd
TimetoTrigger4A
TimetoTrigger4B
PendingTime4A
PendingTime4B
b. Run the BSC6900 MML command SET UDCCC to set the following RNC-
level DCCC algorithm parameters:
DcccStg
UlRateUpAdjLevel
UlRateDnAdjLevel
DlRateUpAdjLevel
DlRateDnAdjLevel
UlDcccRateThd
DlDcccRateThd
UlMidRateCalc
DlMidRateCalc
UlMidRateThd
DlMidRateThd
3. To activate throughput-based BE service rate adjustment, perform the following steps:
a. Run the BSC6900 MML command SET UCORRMALGOSWITCH. In this
step, set Dynamic Resource Allocation Switch to
DRA_THROUGHPUT_DCCC_SWITCH.
b. Run the BSC6900 MML command SET UDCCC. In this step, set DCH Throu
Meas Period and HSUPA DCCC strategy.
c. Run the BSC6900 MML command MOD UTYPRABDCCCMC to set the
following event 4B parameters for the DCH:
Period Amount to trigger 4B on DCH
Period Amount after trigger 4B on DCH
4. To activate link-stability-based BE service rate adjustment, perform the following
steps:
a. Run the BSC6900 MML command SET UQOSACT to set the RNC-level QoS
enhancement algorithm parameters. The parameters for ensuring link stability
are:
QOS Switch for BE Traffic
First Action for BE Uplink QOS
Second Action for BE Uplink QOS
Third Action for BE Uplink QOS
Wait Timer for BE Uplink Rate
First Action for BE Downlink QOS
Second Action for BE Downlink QOS
Third Action for BE Downlink QOS
Indicator for BE Uplink QOS Event
Srnc Parameter for BE Downlink RLC QOS
DRNC Parameter for BE Downlink RLC QOS
The BSC6900 defines default values for Max UL TX power of interactive service and
Max UL TX power of background service. Retain the default values in normal
situations.
d. Run the BSC6900 MML command MOD UCELLRLPWR to set the cell-level
downlink transmit power parameters.
e. Run the BSC6900 MML command MOD UCELLQUALITYMEAS to set the
cell-level QoS measurement parameters. The parameters for ensuring link
stability are:
BE Trigger Time 6A1
BE Trigger Time 6B1
BE Trigger Time 6A2
BE Trigger Time 6B2
BE Trigger Time 6D
BE Trigger Time of Event E
BE Reporting Period Unit for Event E
BE Event E Reporting Period
BE Trigger Time of Event F
The BSC6900 defines default values for the preceding parameters. Retain the default
values in normal situations.
f. Run the BSC6900 MML command MOD UTYPRABQUALITYMEAS to set
the following typical parameters for QoS measurement:
Uplink Event 6A1 Relative Threshold
Uplink Event 6A2 Relative Threshold
Uplink Event 6B1 Relative Threshold
Uplink Event 6B2 Relative Threshold
Statistic Block Number for 5A Event
Event 5A Threshold
Event 5A Interval Block Number
Event Ea Relative Threshold
Event Eb Relative Threshold
g. Run the BSC6900 MML command MOD UTYPRABRLC to set Radio Link
Control (RLC) parameters for a typical Radio Access Bearer (RAB). The
parameters for ensuring link stability are:
Re-TX monitor period
Event A threshold
Hysteresis of Event A
Event A pending time after trigger
Filter Coefficient of RLC Retransmission Ratio
NOTE
The BSC6900 defines default values for the preceding parameters. Retain the default
values in normal situations.
h. Link stability control for BE services is implemented through Inter-frequency
handover.
a. Run the BSC6900 MML command MOD UCELLHOCOMM. In this step,
set Inter-Frequency and Inter-RAT Coexist Switch to INTERFREQ.
b. Run the BSC6900 MML command SET UCORRMALGOSWITCH. In
this step, set HandOver Switch to
HO_INTER_FREQ_HARD_HO_SWITCH.
i. To configure inter-RAT handover for the link stability of BE services, perform
the following steps:
a. Run the BSC6900 MML command MOD UCELLHOCOMM. In this step,
set Inter-Frequency and Inter-RAT Coexist Switch to INTERRAT and
Inter-RAT PS Handover Switch to ON.
b. Run the BSC6900 MML command SET UCORRMALGOSWITCH. In
this step, set HandOver Switch to
HO_INTER_RAT_PS_OUT_SWITCH.
j. To configure inter-frequency handover and inter-RAT handover for the link
stability of BE services, perform the following steps:
The HSDPA state transition license must be activated before the HSDPA state transition switch is
turned on.
2. Run the BSC6900 MML command SET UUESTATETRANS to set the measurement
control parameters of the UE state transition algorithm.
3. Run the BSC6900 MML command SET UUESTATETRANSTIMER to set the
timer parameters of the UE state transition algorithm.
4. Run the BSC6900 MML command SET UDCCC to set Low Activity Bit Rate
Threshold.
l Activating always online
1. Run the BSC6900 MML command SET UPSINACTTIMER to set the following
timer parameters for checking the low activity of PS users:
Conversational service T1
Streaming service T1
Interactive service T1
Background service T1
IMS signal T1
Conversational service T2
Streaming service T2
Interactive service T2
Background service T2
IMS signal T2
l Verifying DCCC
1. Traffic-based BE service rate adjustment
b. Set up an R99 BE service and maintain the service without data operations. In
the Connection Performance Monitoring tab page, you can view the bandwidth
reduction in UL Throughput Bandwidth.
3. Link-stability-based BE service rate adjustment
Set up an R99 BE service and maintain the service without data operations. Check whether
the value of rrc-StateIndicator in the traced RRC_RB_RECFG message is cell-FACH
(1), as shown in Figure 17-5.
Set up an R99 BE service and maintain the service without data operations. The message
RRC_RB_REL is not traced on the Uu interface.
l Deactivation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH to turn off the
related switches.
2. Run the BSC6900 MML command SET UCORRMALGOSWITCH. In this step,
set Dynamic Resource Allocation Switch to DRA_DCCC_SWITCH.
----End
Example
//Activating DCCC
//Activating the DCCC algorithm
SET UCORRMALGOSWITCH: DraSwitch=DRA_DCCC_SWITCH-1;
//Activating traffic-based BE service rate adjustment
MOD UTYPRABDCCCMC: RabIndex=1, Direction=DOWNLINK, Event4aThd=D1024,
Event4bThd=D16, TimetoTrigger4A=D240, PendingTime4A=D4000,
TimetoTrigger4B=D2560, PendingTime4B=D4000;
SET UDCCC: UlDcccRateThd=D64, DlDcccRateThd=D64,
DcccStg=RATE_UP_AND_DOWN_ON_DCH, UlRateUpAdjLevel=3_Rates,
UlRateDnAdjLevel=3_Rates, UlMidRateCalc=HAND_APPOINT, UlMidRateThd=D128,
DlRateUpAdjLevel=3_Rates, DlRateDnAdjLevel=3_Rates,
DlMidRateCalc=HAND_APPOINT, DlMidRateThd=D128;
//Activating throughput-based BE service rate adjustment
SET UCORRMALGOSWITCH: DraSwitch=DRA_THROUGHPUT_DCCC_SWITCH-1;
SET UDCCC: HsupaDcccStg=RATE_UP_AND_DOWN_ON_EDCH, DchThrouMeasPeriod=100;
MOD UTYPRABDCCCMC: RabIndex=1, Direction=UPLINK, Event4bThd=D64,
DchThrouTimetoTrigger4B=2, DchThrouPendingTime4B=16;
SET UUESTATETRANS: E2FThrouMeasPeriod=30;
//Activating link-stability-based BE service rate adjustment
//Setting the QoS-related parameters
SET UQOSACT: BEQosPerform=YES, BeUlAct1=RateDegrade,
BeUlAct2=InterFreqHO, BeUlAct3=InterRatHO, BeDlAct1=RateDegrade,
BeDlAct2=InterFreqHO, BeDlAct3=InterRatHO, BeUlEvTrigInd=SINGLE,
SrncBeDlRlcQosSwitch=YES, DrncBeDlRlcQosSwitch=YES,
BeUlQos6A1McSwitch=YES, BeUlQos5AMcSwitch=YES, BeUlQos6DMcSwitch=YES;
SET UQUALITYMEAS: UlBeTrigTime6A1=D640, UlBeTrigTime6B1=D2560,
UlBeTrigTime6A2=D1280, UlBeTrigTime6B2=D1280, UlBeTrigTime6D=D240,
UlMeasFilterCoef=D19, DlMeasFilterCoef=D1, DlBeTrigTimeE=64,
ChoiceRptUnitForBeE=TEN_MSEC, TenMsecForBeE=480, DlBeTrigTimeF=64,
ChoiceRptUnitForBeF=TEN_MSEC, TenMsecForBeF=480;
MOD UCELLRLPWR: CellId=1, CNDOMAINID=CS_DOMAIN, MAXBITRATE=12200,
RLMAXDLPWR=-30, RLMINDLPWR=-180, DLSF=D128;
MOD UTYPRABQUALITYMEAS: RabIndex=1, UlThd6a1=1, UlThd6a2=5, UlThd6b1=1,
UlThd6b2=5, StaBlkNum5A=500, Thd5a=280, HangBlockNum5a=512, ThdEa=2,
ThdEb=2;
MOD UTYPRABRLC: RabIndex=1, SubflowIndex=0, TrchType=TRCH_DCH,
OppositeTrchType=TRCH_DCH, DelayClass=1, RlcMode=AM,
AmRlcCfgPara=FLOWCONTROL_PARA, TimeToMoniter=6000, MoniterPrd=1000,
ReTransRatioFilterCoef=1, EventAThred=160, TimeToTriggerA=2,
PendingTimeA=1;
//Configuring inter-frequency handover for the link stability of BE
services
MOD UCELLHOCOMM: CellId=1, InterFreqRATSwitch=INTERFREQ,
CoexistMeasThdChoice=COEXIST_MEAS_THD_CHOICE_INTERFREQ,
CSServiceHOSwitch=OFF, PSServiceHOSwitch=OFF;
SET UCORRMALGOSWITCH: HoSwitch=HO_INTER_FREQ_HARD_HO_SWITCH-1;
//Configuring inter-RAT handover for the link stability of BE services
MOD UCELLHOCOMM: CellId=1, InterFreqRATSwitch=INTERRAT,
CoexistMeasThdChoice=COEXIST_MEAS_THD_CHOICE_INTERFREQ,
CSServiceHOSwitch=OFF, PSServiceHOSwitch=ON;
SET UCORRMALGOSWITCH: HoSwitch=HO_INTER_RAT_PS_OUT_SWITCH-1;
//Setting the DCCC algorithm parameters
This section describes how to activate, verify, and deactivate the basic feature WRFD-011401
Integrity Protection.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
Context
This feature protects the network and user data from being listened and modified illegally.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UUIA (CME single configuration: UMTS
Radio Global Configuration Express > Security Mode Configuration > Integrity
Protection Algorithm; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to enable the RNC to support the integrity protection
algorithm.
l Verification Procedure
1. On the BSC6900 LMT, click Trace > UMTS Services, and then double-click Iu
Interface Trace. The Iu Interface Trace dialog box is displayed.
2. Keep UE1 and UE2 in idle mode in CELL1.
3. Use UE2 to call UE1.
4. The messages RANAP_SECURITY_ MODE_COMMAND and
RANAP_SECURITY_MODE_COMPLETE should be displayed. The
chosenIntegrityProtectionAlgorithm IE of the latter message indicates the integrity
protection algorithm.
l Deactivation Procedure
Example
//Activating integrity protection
SET UUIA: IntegrityProtectAlgo=UIA1-1;
19 Configuring Encryption
This section describes how to activate, verify, and deactivate the basic feature WRFD-011402
Encryption.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
Context
The encryption algorithms supported by Huawei RAN include UEA0 and UEA1.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UUEA (CME single configuration: UMTS
Radio Global Configuration Express > Security Mode Configuration >
Encryption Algorithm; CME batch modification center: not supported) to enable the
RNC to support the encryption algorithm.
l Verification Procedure
1. On the BSC6900 LMT, click Trace > UMTS Services, and then double-click Iu
Interface Trace. The Iu Interface Trace dialog box is displayed.
2. Keep UE1 and UE2 in idle mode in CELL1.
3. Use UE2 to call UE1.
4. The messages RANAP_SECURITY_ MODE_COMMAND and
RANAP_SECURITY_MODE_COMPLETE should be displayed. The
chosenEncryptionAlgorithm IE of the latter message indicates the encryption
algorithm.
5. End the calling. UE1 and UE2 return to the idle mode.
Example
//Activating encryption
SET UUEA: EncryptionAlgo=UEA0-1&UEA1-1;
This section describes how to activate, verify, and deactivate the basic feature WRFD-020501
Open Loop Power Control.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
Context
This feature enables BSC6900 to roughly estimate path loss based on power measurement
results, network parameter settings, and QoS requirements. Based on the estimation results,
BSC6900 sets the initial transmit power for a UE and a NodeB before connection is established
between them.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UFRC (CME single configuration: UMTS
Radio Global Configuration Express > Basic Resource Control Parameter
Configuration > RNC Oriented FRC Algorithm Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches). In this step, set
the parameters related to uplink DPCH power control.
NOTE
l The BSC6900 uses the Default Constant Value parameter to calculate the power offset
on the uplink DPCCH (DPCCH_Power_offset). Based on the calculation result, the UE
calculates the initial transmit power on the uplink DPCCH (DPCCH_Initial_Power).
l The formula for calculating DPCCH_Power_offset is: DPCCH_Power_offset = Primary
CPICH DL TX power + UL interference + Default Constant Value. Where,
DPCCH_Power_offset indicates the initial transmit power offset on the DPCCH, Primary
CPICH DL TX power indicates the downlink transmit power on the P-CPICH, UL
interference indicates the uplink interference, and Default Constant Value is the value of
Default Constant Value.
l The formula for calculating DPCCH_Initial_Power is: DPCCH_Initial_Power =
DPCCH_Power_offset - CPICH_RSCP. Where, CPICH_RSCP indicates the received
signal code power (RSCP) that the UE measures on the P-CPICH. An excessively small
value of DPCCH_Power_offset may lead to uplink synchronization failures at the cell edge
during initial link establishment, which affects uplink coverage. An excessively great value
of DPCCH_Power_offset may lead to instantaneous interference on uplink signal
reception, which affects the uplink receiving performance. For details, see 3GPP TS 25.331.
l Deactivation Procedure
1. This feature does not need to be deactivated.
----End
Example
//Activating open loop power control on the uplink DPCH
SET UFRC: DefaultConstantValue=-22;
This section describes how to activate, verify, and deactivate the basic feature WRFD-020502
Downlink Power Balance.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
Context
In soft handover, error codes in a TPC command may lead to downlink transmit power drift.
The downlink power balance feature solves the problem of power imbalance between links,
thereby achieving best gain in soft handover. The greater the downlink transmit power drift, the
smaller the macro diversity gain. Downlink power balance adjusts power drift and improves
performance of soft handover.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, set Power Control Switch to
PC_DOWNLINK_POWER_BALANCE_SWITCH.
l Verification Procedure
1. On the BSC6900 LMT, choose Trace > UMTS Services and double-click Uu
Interface Trace. The Uu Interface Trace dialog box is displayed.
2. Set Cell Config, Uu Message Type, and Save File. Then click Submit.
3. Move a UE from cell 1 to cell 2 to ensure that the UE performs a soft handover.
4. Check whether the active cell set update is complete in the traced Uu-interface
messages. Figure 21-1 shows the expected result.
5. Start Iub interface message tracing on the BSC6900 LMT. Check the value of the
information element dedicatedMeasurementType in the
NBAP_DEDIC_MEAS_INIT_REQ message.
Expected result: the value of dedicatedMeasurementType is transmitted-code-
power(2) shown in Figure 21-2.
l Deactivation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, set
PC_DOWNLINK_POWER_BALANCE_SWITCH to 0.
----End
Example
//Activating downlink power balance SET UCORRMALGOSWITCH:
PcSwitch=PC_DOWNLINK_POWER_BALANCE_SWITCH-1;
//Deactivating downlink power balance SET UCORRMALGOSWITCH:
PcSwitch=PC_DOWNLINK_POWER_BALANCE_SWITCH-0;
This section describes how to activate, verify, and deactivate the basic feature WRFD-020503
Outer Loop Power Control.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
Context
Outer loop power control guarantees the service quality by adjusting the target SIR of inner loop
power control. Outer loop power control is performed on the DCHs carrying the same RRC
connection. When the moving speed of a UE or the multi-path environment changes, the target
SIR needs to be adjusted to ensure a desirable service quality. Otherwise, the service quality
may be bad or will accordingly lead to severe interference and power waste.
The legacy OLPC algorithm enables the target SIR to quickly increase but slowly decrease,
therefore leading to a waste of uplink power. The optimized OLPC algorithm rapidly adjusts the
target SIR in any of the following scenarios: service setup, service reconfiguration, burst
interference, and status switching between insufficient UE transmit power and sufficient UE
transmit power. By doing so, the average uplink target SIR is reduced and the uplink power
consumption is decreased.
Procedure
l Activation Procedure
Activating outer loop power control
1. Run the Run the BSC6900 MML command SET UCORRMALGOSWITCH
(CME single configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to activate outer loop power control. In this step, select
the PC_OLPC_SWITCH check box under the PcSwitch parameter.
2. Optional: Run the Run the BSC6900 MML command MOD
UTYPRABOLPC (CME single configuration: UMTS Radio Global
Configuration Express > Typical Service Configuration > Typical RAB
OLPC Parameters; CME batch modification center: not supported). In this step,
set the parameters related to outer loop power control based on the network plan.
Activating optimized outer loop power control
NOTE
You need to activate outer loop power control before activating optimized outer loop power control.
3. When the service is successfully set up, check whether the adjustment value of the
target SIR is the same as the specified value in each OLPC period. If they are the
same, this feature has been activated.
l Deactivation Procedure
Deactivating outer loop power control
1. Run the Run the BSC6900 MML command SET UCORRMALGOSWITCH
(CME single configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to deactivate outer loop power control. In this step, clear
the PC_OLPC_SWITCH check box under the PcSwitch parameter.
Deactivating optimized outer loop power control
1. Run the Run the BSC6900 MML command SET UCORRMALGOSWITCH
(CME single configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to deactivate optimized outer loop power control. In this
step, clear the PC_OLPC_FASTDOWN_OPTIMIZE_SWITCH check box
under the PcSwitch parameter.
----End
Example
//Activating Outer Loop Power Control
SET UCORRMALGOSWITCH: PcSwitch=PC_OLPC_SWITCH-1;
//Setting the parameters related to outer loop power control
MOD UTYPRABOLPC: RabIndex=11, SubflowIndex=0, TrchType=TRCH_DCH,
DelayClass=1, BLERQuality=-20;
//Deactivating Outer Loop Power Control
SET UCORRMALGOSWITCH: PcSwitch=PC_OLPC_SWITCH-0;
This section describes how to activate, verify, and deactivate the basic feature WRFD-020504
Inner Loop Power Control.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
Context
Inner loop power control is also known as fast close loop power control. It is applied for dedicated
channels only. It is used to adjust the transmit power based on the feedback from the physical
layer of the peer end. The UE and Node B can adjust transmit power according to the SIR sent
by each other. In this way, radio link fading can be reduced.
Procedure
l Activation Procedure
1. The feature does not need to be activated.
l Verification Procedure
1. Click the Monitor on the BSC6900 LMT main page. On the Monitor Navigation
Tree pane, choose Monitor > UMTS Monitoring > Connection Performance
Monitoring. The Connection Performance Monitoring dialog box is displayed. In
the displayed dialog box, set Monitor Item to UL SIR and UE Tx Power, and enter
the corresponding IMSI. And then click Submit to initiate the trace.
2. UE 1 calls UE 2. UE 2 rings, answers and starts the conversation.
3. Observe the variation of UL SIR and UE Tx Power in the UL SIR and UE Tx
Power Connection Performance Monitoring window.
4. UE 1 moves in the cell to change radio link quality.
5. When you move UE 1 away from the cell center, UE_1 transmit power increases.
6. When you move UE_1 towards cell center, UE_1 transmit power decreases.
l Deactivation Procedure
1. This feature does not need to be deactivated.
----End
This section describes how to activate, verify, and deactivate the basic feature WRFD-020101
Admission Control.
Prerequisites
l Dependencies on Hardware
Uplink power admission algorithm 4 introduced in RAN14.0 is based on the actual
service load, which is reported by the NodeB. However, some boards cannot support
the measurement of the service load.
The BTS3812E, BTS3812A and BTS3812AE do not support uplink power
admission algorithm 4.
The DBS3800 does not support uplink power admission algorithm 4.
If the 3900 series base station is configured with the WBBPa board or the RRU3801C
20W, uplink power admission algorithm 4 is not supported. In other configurations,
the algorithm is supported.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
Context
This feature enables the BSC6900 to perform admission control on UEs requesting R99 services
by considering the status of various resources. It helps ensure the QoS and optimize the allocation
of system resources.
Procedure
l Activation Procedure
1. Activating code resource admission
Run the BSC6900 MML command MOD UCELLCAC (CME single configuration:
UMTS Cell Configuration Express > Cell Parameters > Cell Oriented CAC
Algorithm Parameters; CME batch modification center: 3.18 Modifying UMTS
Cell Parameters in Batches) with Dl handover credit and code reserved SF set to
an appropriate value.
2. Activating power resource admission
a. Run the BSC6900 MML command MOD UCELLALGOSWITCH (CME
single configuration: UMTS Cell Configuration Express > Cell Parameters
> Cell Algorithm Switches; CME batch modification center: 3.18 Modifying
UMTS Cell Parameters in Batches). In this step, select associated cell-oriented
power admission control algorithms from the Cell CAC algorithm switch drop-
down list, and select an appropriate algorithm from both the Uplink CAC
algorithm switch and Downlink CAC algorithm switch drop-down lists
according to the network plan.
b. Run the BSC6900 MML command MOD UCELLCAC (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Oriented CAC Algorithm Parameters; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches) to set power resource
admission parameters to appropriate values.
3. Activating NodeB credit resource admission
a. Run the BSC6900 MML command SET UCACALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express > CAC
Algorithm Switch Configuration > CAC Algorithm Switch; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches). In this step,
select NODEB_CREDIT_CAC_SWITCH from the CAC algorithm switch
drop-down list to turn on the NodeB-level CE admission switch.
b. Run the BSC6900 MML command MOD UCELLALGOSWITCH (CME
single configuration: UMTS Cell Configuration Express > Cell Parameters
> Cell Algorithm Switches; CME batch modification center: 3.18 Modifying
UMTS Cell Parameters in Batches). In this step, select CRD_ADCTRL
(Credit Admission Control Algorithm) from the Cell CAC algorithm
switch drop-down list to turn on the NodeB-level credit admission switch.
c. Run the BSC6900 MML command MOD UCELLCAC (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Oriented CAC Algorithm Parameters; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches). In this step, set UL handover
credit reserved SF to an appropriate value.
4. Activating Iub resource admission
This feature does not need to be activated.
l Verification Procedure
The procedure for verifying downlink admission control on R99 non-real-time PS services
based on the number of equivalent subscribers is as follows:
1. Enable a UE in the idle state to camp on CELL_A11.
2. Set the PS service type to interactive on the HLR.
3. Run the BSC6900 MML command MOD UCELLCAC. In this step, set DL total
equivalent user number of CELL_A11 to 1.
4. Connect the UE to a laptop through the USB port and initiate a PS service.
Expected result: The UE fails to initiate the PS service. In the Iu Interface Trace
window, an RANAP_RAB_ASSIGNBMENT_RESP message sent from the RNC to
the CN is displayed, containing the cause value no-radio-resources-available-in-
target-cell.
5. Run the BSC6900 MML command MOD UCELLCAC. In this step, set DL total
equivalent user number of CELL_A11 to 80.
6. Connect the UE to a laptop through the USB port and initiate a PS service.
Expected result: The data service is set up successfully.
l Deactivation Procedure
1. Deactivating code resource admission
This feature does not need to be deactivated.
2. Deactivating power resource admission
----End
Example
//Activating code resource admission
MOD UCELLCAC: CellId=11, UlNonCtrlThdForAMR=75, UlNonCtrlThdForNonAMR=75,
UlNonCtrlThdForOther=60, DlConvAMRThd=80, DlConvNonAMRThd=80,
DlOtherThd=75, UlNonCtrlThdForHo=80, DlHOThd=85, UlCellTotalThd=83,
DlCellTotalThd=90, DlHoCeCodeResvSf=SF32;
//Activating power resource admission
MOD UCELLALGOSWITCH: CellId=11, NBMUlCacAlgoSelSwitch=ALGORITHM_FIRST,
NBMDlCacAlgoSelSwitch=ALGORITHM_SECOND;
MOD UCELLALGOSWITCH: CellId=11,
NBMCacAlgoSwitch=HSDPA_UU_ADCTRL-1&HSDPA_GBP_MEAS-1&HSDPA_PBR_MEAS-1;
MOD UCELLCAC: CellId=11, MaxHsdpaUserNum=64, MaxUlTxPowerforConv=24,
MaxUlTxPowerforInt=24;
//Activating NodeB credit resource admission
SET UCACALGOSWITCH: CacSwitch=NODEB_CREDIT_CAC_SWITCH-1;
MOD UCELLALGOSWITCH: CellId=11, NBMCacAlgoSwitch=CRD_ADCTRL-1;
MOD UCELLCAC: CellId=11, UlHoCeResvSf=SF16;
//Deactivating power resource admission
MOD UCELLALGOSWITCH: CellId=11, NBMUlCacAlgoSelSwitch=ALGORITHM_OFF,
NBMDlCacAlgoSelSwitch=ALGORITHM_OFF;
This section describes how to activate, verify, and deactivate the basic feature WRFD-020102
Load Measurement.
Prerequisites
l Dependencies on Hardware
In RAN14.0, the load measurement of total uplink services is introduced, and the
dependencies on NodeB are as follows:
The BTS3812, BTS3812E and BTS3812AE do not report the actual service load.
The DBS3800 does not report the actual service load.
If the 3900 series base station is configured with the WBBPa board or the RRU3801C
20W, the actual service load is not reported. In other configurations, the actual
service load is reported.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
Context
This feature is used to measure the load for the load control feature.
Procedure
l Activation Procedure
1. The function of measurement on RTWP, TCP, and non-HSPA power is always
activated. Therefore, this feature does not need to be activated.
2. Run the BSC6900 MML command MOD UCELLALGOSWITCH (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Algorithm Switches; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches). In this step, select HSDPA_PBR_MEAS(HSDPA PBR
Meas Algorithm) and HSUPA_PBR_MEAS(HSUPA PBR Meas Algorithm) from
the Cell CAC algorithm switch drop-down list to activate the cell-level load
measurement for HSDPA and HSUPA.
3. Run the BSC6900 MML command MOD UCELLLDM (CME single configuration:
UMTS Cell Configuration Express > Cell Parameters > Cell Oriented LDM
Algorithm Parameters; CME batch modification center: 3.18 Modifying UMTS
Cell Parameters in Batches). In this step, set load monitoring parameters, including
the uplink/downlink load reshuffling (LDR) algorithm trigger/release thresholds and
uplink/downlink overload congestion (OLC) algorithm trigger/release thresholds to
appropriate values.
4. Run the BSC6900 MML command SET ULDM (CME single configuration: UMTS
Radio Global Configuration Express > Load Monitoring Parameter
Configuration > LDM Algorithm Parameters of RNC; CME batch modification
center: 3.15 Modifying RNC Parameters in Batches). In this step, set parameters
associated with load measurement, report period, and smoothing filter length
according to the network plan.
l Verification Procedure
1. On the BSC6900 LMT, open the Monitor page. In the Monitor navigation tree,
double-click UMTS Monitoring > Cell Performance Monitoring, and create tasks
of monitoring Cell DL Carrier TX Power and RTWP.
2. Check whether the uplink full-bandwidth RX power of the cell is displayed in the
RTWP monitoring window.
3. Check whether the downlink carrier TX power is displayed in the Cell DL Carrier
TX Power monitoring window.
l Deactivation Procedure
1. The measurement on RTWP, TCP, and non-HSPA power has been activated and
cannot be deactivated.
2. Run the BSC6900 MML command MOD UCELLALGOSWITCH (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Algorithm Switches; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches). In this step, deselect HSDPA_PBR_MEAS(HSDPA PBR
Meas Algorithm) and HSUPA_PBR_MEAS(HSUPA PBR Meas Algorithm) from
the Cell CAC algorithm switch drop-down list to deactivate the cell-level load
measurement for HSDPA and HSUPA.
----End
Example
//Activating load measurement
MOD UCELLALGOSWITCH: CellId=100,
NBMCacAlgoSwitch=HSDPA_PBR_MEAS-1&HSUPA_PBR_MEAS-1;
MOD UCELLLDM: CellId=1, UlLdrTrigThd=55, UlLdrRelThd=45, DlLdrTrigThd=70,
DlLdrRelThd=60, UlOlcTrigThd=95, UlOlcRelThd=85, DlOlcTrigThd=95,
DlOlcRelThd=85, HsupAuRetrnsLdTrigThd=70, HsupAuRetrnsLdRelThd=50;
SET ULDM: UlBasicCommMeasFilterCoeff=D6,
ChoiceRprtUnitForUlBasicMeas=TEN_MSEC, TenMsecForUlBasicMeas=100,
DlBasicCommMeasFilterCoeff=D6;
//Deactivating load measurement
MOD UCELLALGOSWITCH: CellId=100,
NBMCacAlgoSwitch=HSDPA_PBR_MEAS-0&HSUPA_PBR_MEAS-0;
This section describes how to activate, verify, and deactivate the basic feature WRFD-020106
Load Reshuffling.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
Context
This feature provides multiple load reshuffling policies for a cell in the basic congestion state
to decrease the cell load and increase the access success rate. The load reshuffling policies are
inter-frequency load handover, code reshuffling, BE service rate reduction, uncontrolled real-
time traffic QoS renegotiation, CS domain inter-RAT load handover, PS domain inter-RAT load
handover, downsizing the bit rate of AMR voice, and MBMS power downgrading.
Procedure
l Activation Procedure
NOTE
The following section provides the related parameters and commands. The parameter settings depend
on the network plan.
1. Enable the related load reshuffling algorithms.
a. Run the BSC6900 MML command MOD UCELLALGOSWITCH (CME
single configuration: UMTS Cell Configuration Express > Cell Parameters
> Cell Algorithm Switches; CME batch modification center: 3.18 Modifying
UMTS Cell Parameters in Batches). In this step, turn on the following switches
of Cell LDC algorithm switch:
UL_UU_LDR(Uplink UU LDR Algorithm): UL UU load reshuffling
algorithm
Information > NodeB Algorithm Parameters; CME batch modification center: 3.16
Modifying Logical NodeB Parameters in Batches). In this step, deselect the
following switches from NodeB LDC algorithm switch:
IUB_LDR(IUB LDR Algorithm): NodeB Iub reshuffling algorithm
NODEB_CREDIT_LDR(NodeB Credit LDR Algorithm): NodeB-level credit
reshuffling algorithm
LCG_CREDIT_LDR(LCG Credit LDR Algorithm): cell-group-level credit
reshuffling algorithm
----End
Example
//Activating Load Reshuffling
//Enabling load reshuffling algorithms
MOD UCELLALGOSWITCH: CellId=100,
NBMLdcAlgoSwitch=UL_UU_LDR-1&DL_UU_LDR-1&CELL_CODE_LDR-1&CELL_CREDIT_LDR-
1;
MOD UNODEBALGOPARA: NodeBName="nodeb1",
NodeBLdcAlgoSwitch=IUB_LDR-1&NODEB_CREDIT_LDR-1&LCG_CREDIT_LDR-1;
//Setting load reshuffling thresholds
MOD UCELLLDM: CellId=100, UlLdrTrigThd=55, UlLdrRelThd=45,
DlLdrTrigThd=70, DlLdrRelThd=60, UlOlcTrigThd=95, UlOlcRelThd=85,
DlOlcTrigThd=95, DlOlcRelThd=85, DlLdTrnsHysTime=1000;
//Setting code reshuffling thresholds
MOD UCELLLDR: CellId=100, DlLdrFirstAction=CodeAdj,
DlLdrSecondAction=InterFreqLDHO, CellLdrSfResThd=SF8;
//Setting NodeB-level credit reshuffling thresholds
MOD UNODEBLDR: NodeBName="nodeb1", UlLdrCreditSfResThd=SF8,
DlLdrCreditSfResThd=SF8;
//Setting cell-level credit reshuffling thresholds
MOD UCELLLDR: CellId=100, UlLdrCreditSfResThd=SF8,
DlLdrCreditSfResThd=SF8;
//Setting load reshuffling period
SET ULDCPERIOD: LDRPERIODTIMERLEN=10;
//Turning on load reshuffling function switches
SET UCORRMALGOSWITCH:
PsSwitch=PS_BE_IU_QOS_NEG_SWITCH-1,DraSwitch=DRA_DCCC_SWITCH-1,CsSwitch=C
S_AMRC_SWITCH-1,
HoSwitch=HO_ALGO_LDR_ALLOW_SHO_SWITCH-1&HO_INTER_RAT_CS_OUT_SWITCH-1&HO_I
NTER_RAT_PS_OUT_SWITCH-1;
This section describes how to activate, verify, and deactivate the basic feature WRFD-020107
Overload Control.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
Context
This feature provides load adjustment means to quickly lower the load in overloaded cells.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command MOD UCELLALGOSWITCH (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Algorithm Switches; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches) to enable the air interface OLC algorithm. Select the
UL_UU_OLC(Uplink UU OLC Algorithm) and DL_UU_OLC(Downlink UU
OLC Algorithm) check boxes under the parameter Switch for Cell Load Control.
2. Run the BSC6900 MML command MOD UNODEBALGOPARA (CME single
configuration: NodeB Configuration Express > IUB_RNC > NodeB Basic
Information > NodeB Algorithm Parameters; CME batch modification center: 3.16
Modifying Logical NodeB Parameters in Batches) to enable the OLC algorithm.
Select the IUB_OLC(IUB OLC Algorithm) check box under the parameter NodeB
LDC algorithm.
3. Run the BSC6900 MML command MOD UCELLLDM (CME single configuration:
UMTS Cell Configuration Express > Cell Parameters > Cell Oriented LDM
Algorithm Parameters; CME batch modification center: 3.18 Modifying UMTS
Consult Huawei engineers about the verification solution to obtain professional technical support.
NOTE
l Deactivation Procedure
1. Run the BSC6900 MML command MOD UCELLALGOSWITCH (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Algorithm Switches; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches) to dienable the air interface OLC algorithm. Clear the
UL_UU_OLC(Uplink UU OLC Algorithm) and DL_UU_OLC(Downlink UU
OLC Algorithm) check boxes under the parameter Switch for Cell Load Control.
2. Run the BSC6900 MML command MOD UNODEBALGOPARA (CME single
configuration: NodeB Configuration Express > IUB_RNC > NodeB Basic
Information > NodeB Algorithm Parameters; CME batch modification center: 3.16
Modifying Logical NodeB Parameters in Batches) to disenable the OLC algorithm,
Clear the IUB_OLC(IUB OLC Algorithm) check box under the parameter NodeB
LDC algorithm.
----End
Example
//Activating Overload Control
MOD UCELLALGOSWITCH: CellId=111,
NBMLdcAlgoSwitch=UL_UU_OLC-1&DL_UU_OLC-1;
MOD UNODEBALGOPARA: NodeBName="NodeB1", NodeBLdcAlgoSwitch=IUB_OLC-1;
SET ULDCPERIOD: OlcPeriodTimerLen=3000;
ADD UCELLOLC: CellId=111;
//Deactivating Overload Control
MOD UCELLALGOSWITCH: CellId=111,
NBMLdcAlgoSwitch=UL_UU_OLC-0&DL_UU_OLC-0;
MOD UNODEBALGOPARA: NodeBName="NodeB1", NodeBLdcAlgoSwitch=IUB_OLC-0;
This section describes how to activate, verify, and deactivate the optional feature WRFD-020108
Code Resource Management.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
Context
This feature provides downlink code tree allocation and reshuffling. Through this, the code
resources can be rationally allocated, therefore increasing the utilization efficiency of the
resources.
Procedure
l Activation Procedure
NOTE
The code allocation function is always activated. The activation procedure applies to only the code
reshuffling function.
1. Run the BSC6900 MML command MOD UCELLALGOSWITCH (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Algorithm Switches; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches), and then enable the required LDR algorithm switches for
resources (CELL_CODE_LDR(Code LDR Algorithm)) through setting the Cell
LDC algorithm switch parameter.
2. Run the BSC6900 MML command MOD UCELLLDR (CME single configuration:
UMTS Cell Configuration Express > Cell Parameters > Cell LDR Algorithm
Parameters; CME batch modification center: 3.18 Modifying UMTS Cell
Example
//Activating Code Resource Management
MOD UCELLALGOSWITCH: CellId=111, NBMLdcAlgoSwitch=CELL_CODE_LDR-1;
MOD UCELLLDR: CellId=111, DlLdrFirstAction=CodeAdj, CellLdrSfResThd=SF8;
SET ULDCPERIOD: LdrPeriodTimerLen=10;
//Verifying Code Resource Management
MOD UCELLLDR: CellId=111, CellLdrSfResThd=SF8, MaxUserNumCodeAdj=1;
DSP UCELLCHK: CHECKSCOPE=CELLID, CELLID=111;
RMV URESERVEOVSF: CellId=111, DLOVSFSF=SF32, DLCODENO=1;
//Deactivating Code Resource Management
MOD UCELLALGOSWITCH: CellId=111, NBMLdcAlgoSwitch=CELL_CODE_LDR-0;
This section describes how to activate, verify, and deactivate the optional feature WRFD-020105
Potential User Control.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature reduces system load by modifying cell selection and reselection parameters. In this
way, the cell where the UE camps can be controlled based on cell load.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command MOD UCELLALGOSWITCH (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Algorithm Switches; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches) to select PUC(Potential User Control Algorithm) from
the Switch for Cell Load Control drop list to enable the cell-oriented PUC algorithm.
2. Run the BSC6900 MML command SET ULDCPERIOD (CME single configuration:
UMTS Radio Global Configuration Express > Load Control Parameter
Configuration > RNC Oriented LDC Algorithm Cycle Length; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches) to specify the
period of potential user control. In this step, set PUC period timer length to an
appropriate value.
3. Run the BSC6900 MML command ADD UCELLPUC (CME single configuration:
UMTS Cell Configuration Express > Cell Parameters > Cell Oriented PUC
Example
//Activating Potential User Control
MOD UCELLALGOSWITCH: CellId=111, NBMLdcAlgoSwitch=PUC-1;
SET ULDCPERIOD: PucPeriodTimerLen=1800;
ADD UCELLPUC: CELLID=1, SPUCLIGHT=45, SPUCHEAVY=70, SPUCHYST=5,
OFFSINTERLIGHT=-2, OFFSINTERHEAVY=2, OFFQOFFSET1LIGHT=-4,
OFFQOFFSET2LIGHT=-4, OFFQOFFSET1HEAVY=4, OFFQOFFSET2HEAVY=4;
//Deactivating Potential User Control
MOD UCELLALGOSWITCH: CellId=111, NBMLdcAlgoSwitch=PUC-0;
This section describes how to activate, verify, and deactivate the optional feature WRFD-021102
Cell Barring.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
If the cell barring feature is enabled, cells can be barred either automatically or manually to
facilitate operators' maintenance when the cells are running improperly.
Procedure
l Activation Procedure
Setting automatic cell barring
1. Run the BSC6900 MML command SET URRCTRLSWITCH (CME single
configuration: UMTS Radio Global Configuration Express > Process Switch
Configuration > Process Switch; CME batch modification center: 3.15
Modifying RNC Parameters in Batches). In this step, select
SYS_INFO_UPDATE_FOR_IU_RST and
BARRED_CELL_FOR_CSDOMAIN_RST from the Process switch drop-
down list.
2. Run the BSC6900 MML command SET UIUTIMERANDNUM (CME single
configuration: IUPS Configuration Express > CN > IU Timers And Counter
for CN Node; CME batch modification center: not supported) to enable
interruption protection by specifying CN protection timer.
Perform the same verification procedure when blocking the CS domain or the CS domain is
disconnected.
1. Click to display Uu Interface Trace on the BSC6900 LMT. Under Uu Message
Type, select RRC_SYS_INFO_TYPE1.
2. View whether information element (IE) information of the PS domain is contained
in the traced messages. Expected result: PS domain IE information is not contained,
as shown in Figure 30-1.
Block CS and PS domains, CS and PS domains are disconnected, or block the CS domain
and turn on BARRED_CELL_FOR_CSDOMAIN_RST. Perform the following steps
to verify whether this feature is activated:
1. Click to display Uu Interface Trace on the BSC6900 LMT. Under Uu Message
Type, select RRC_SYS_INFO_TYPE3.
2. View whether IE information related to CS and PS domains is contained in the
traced messages. Expected result: The IE information is not contained, as shown
in Figure 30-2.
Bar PS services of UEs served by an operator. Perform the following steps to verify
whether this feature is activated:
NOTE
Perform the same verification procedure when barring CS services of UEs served by an operator.
l Deactivation Procedure
Deactivating automatic cell barring
1. Run the BSC6900 MML command SET URRCTRLSWITCH (CME single
configuration: UMTS Radio Global Configuration Express > Process Switch
Configuration > Process Switch; CME batch modification center: 3.15
Modifying RNC Parameters in Batches). In this step, deselect
SYS_INFO_UPDATE_FOR_IU_RST and
BARRED_CELL_FOR_CSDOMAIN_RST from the Process switch drop-
down list.
Deactivating manual cell barring
1. Run the BSC6900 MML command RMV URNCALLCELLBLK (CME single
configuration: UMTS Radio Global Configuration Express > Access
Restriction Algorithm Parameters Configuration > The Parameters for
Quickly Blocking all the Cells in the RNC; CME batch modification center: not
supported) to remove parameters related to barring of all cells served by an RNC
in a network.
2. Run the BSC6900 MML command RMV UCNOPALLCELLBLK (CME single
configuration: UMTS Radio Global Configuration Express > Access
Restriction Algorithm Parameters Configuration > The Parameters for
Quickly Blocking all the Cells of the Designated Operator in the RNC; CME
Example
//Activating Cell Barring
SET URRCTRLSWITCH: PROCESSSWITCH = SYS_INFO_UPDATE_FOR_IU_RST-1;
SET URRCTRLSWITCH: PROCESSSWITCH = BARRED_CELL_FOR_CSDOMAIN_RST-1;
SET UIUTIMERANDNUM: CnOpIndex=0, CNId=0, StateIndTmr=20000;
//Deactivating Cell Barring
SET URRCTRLSWITCH: PROCESSSWITCH = SYS_INFO_UPDATE_FOR_IU_RST-0;
SET URRCTRLSWITCH: PROCESSSWITCH = BARRED_CELL_FOR_CSDOMAIN_RST-0;
This section describes how to activate, verify, and deactivate the basic feature WRFD-021301
Shared Network Support in Connected Mode. (This feature cannot be configured using the
CME. )
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
l Other Prerequisites
CN must support this feature. When the Iur interface is used, the RNC connected over
the interface must also support this feature.
Context
This feature enables the RAN and CN together to perform UE access restriction in specified
location areas.
Procedure
l Activation Procedure
1. For the CS service, configure two SNAs (for example, SNA1 and SNA2) on the MSC.
2. For the PS service, run the MML command ADD SNA on the SGSN to add SNA,
SNA1, and SNA2.
3. Run the BSC6900 MML command MOD UCELLACINFO to modify the RACs of
CELL1 and CELL2.
4. Set up a cell. For details, see the BSC6900 UMTS Initial Configuration Guide.
5. Run the BSC6900 MML command to turn on the soft handover switch.
CELL2 belongs to SNA2 but not SNA1. Therefore, the RRC_MEAS_CTRL message sent from
the RNC to UE1 on the Uu interface should indicate that CELL2 is not in the monitoring cell.
10. Move UE1 to CELL2, which will not trigger soft handover because UE1 does not
belong to SNA_2.
11. End the calling. UE1 and UE2 return to the idle mode in CELL1.
l Verifying the SNA Function of the PS Service
1. Run the MML command ADD SNA on the SGSN to add SNA information.
2. Run the BSC6900 MML command to disable the SNA function.
3. Keep the UE in idle mode in CELL1.
4. Establish a PS service on UE1. The RANAP_COMMON_ID message from UE1
should be displayed in Iu trace data, and it should include the SNA ACCESS
information IE.
5. Move UE1 to CELL2 to trigger soft handover. The RRC_ACTIVE_SET_UPDATE
message from the RNC to UE1 and the RRC_ACTIVE_SET_UPDATE_CMP
message from UE1 to the RNC should be displayed in Uu trace data.
6. End the PS service of UE1. UE1 returns to the idle mode in CELL1.
7. Run the BSC6900 MML command to enable the SNA function.
8. Establish a PS service on UE1. The RANAP_COMMON_ID message from UE1
should be displayed in Iu trace data, and it should include the SNA ACCESS
information IE.
9. CELL2 belongs to SNA2 but not SNA1. Therefore, the RRC_MEAS_CTRL message
sent from the RNC to UE1 on the Uu interface should indicate that CELL2 is not in
the monitoring set.
10. Move UE1 to CELL2, which will not trigger soft handover because UE1 does not
belong to SNA_2.
11. End the PS service of UE1. UE1 returns to the idle mode in CELL1.
l Deactivation Procedure
Example
//Adding two SNAs (for example, SNA1 and SNA2) on the MSC
ADD LOCNOLAI: LOCNONAME="SNA_1", LAI="460020001";
ADD LOCSNA: LOCNONAME=" SNA_1", SNAC=1;
ADD SNAGRPCODE: SNAGRPN="1", SNAC=1;
ADD LOCNOLAI: LOCNONAME="SNA_2", LAI="460020002";
ADD LOCSNA: LOCNONAME=" SNA_2", SNAC=2;
ADD SNAGRPCODE: SNAGRPN="2", SNAC=2;
//Activating the SNA function of the CS Service
MOD UCELLACINFO: CellId=1, LAC=1, SAC=0, CfgRacInd=REQUIRE, RAC=1;
MOD UCELLACINFO: CellId=2, LAC=2, SAC=0, CfgRacInd=REQUIRE, RAC=2;
SET UCORRMALGOSWITCH: HoSwitch=HO_INTRA_FREQ_SOFT_HO_SWITCH-1;
SET UCORRMALGOSWITCH: HoSwitch=HO_MC_SNA_RESTRICTION_SWITCH-1;
//Verifying the SNA function of the CS Service
SET UCORRMALGOSWITCH: HoSwitch=HO_MC_SNA_RESTRICTION_SWITCH-0;
SET UCORRMALGOSWITCH: HoSwitch=HO_MC_SNA_RESTRICTION_SWITCH-1;
///Add a mapping relation between IMSI and SNA1 on the MSC
ADD IMSIGRP: IMSIPRE=K'460071104008338, MCCMNC1=K'46002, SNAGRPN1="1";
MOD RNC: RNCID=1, CAPABILITY=SNA-1;
//Deactivating the SNA function
SET UCORRMALGOSWITCH: HoSwitch=HO_MC_SNA_RESTRICTION_SWITCH-0;
//Adding two SNAs (for example, SNA1 and SNA2) on the SGSN
ADD SNA: PLMN="46002", LAC="1", SNAC=1;
ADD SNA: PLMN="46002", LAC="2", SNAC=2;
//Activating the SNA function of the PS Service
MOD UCELLACINFO: CellId=1, LAC=1, SAC=0, CfgRacInd=REQUIRE, RAC=1;
MOD UCELLACINFO: CellId=2, LAC=2, SAC=0, CfgRacInd=REQUIRE, RAC=2;
SET UCORRMALGOSWITCH: HoSwitch=HO_INTRA_FREQ_SOFT_HO_SWITCH-1;
SET UCORRMALGOSWITCH: HoSwitch=HO_MC_SNA_RESTRICTION_SWITCH-1;
//Adding SNA information on the SGSN
ADD SNAA: BEGIMSI="460071104008338", ENDIMSI="460071104008338",
PLMN="46002", SNAC=1;
//Verifying the SNA function of the PS Service
SET UCORRMALGOSWITCH: HoSwitch=HO_MC_SNA_RESTRICTION_SWITCH-0;
SET UCORRMALGOSWITCH: HoSwitch=HO_MC_SNA_RESTRICTION_SWITCH-1;
//Deactivating the SNA function
SET UCORRMALGOSWITCH: HoSwitch=HO_MC_SNA_RESTRICTION_SWITCH-0;
This section describes how to activate, verify, and deactivate the basic feature WRFD-020201
Intra NodeB Softer Handover.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
Context
This feature enables softer handover within a NodeB. Intra-NodeB softer handover is one type
of soft handover. To perform softer handover, multiple RLs need to be established. In this way,
the uplink resources of a cell in the same uplink resource group can be fully shared. In contrast
to soft handover, softer handover does not consume additional transmission resources on the Iub
interface. Therefore, softer handover can provide higher combination gain and require less
transmission resources on the Iub interface.
Softer handover may occur within the same uplink resource group.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, select
HO_INTRA_FREQ_SOFT_HO_SWITCH under HandOver Switch to enable
soft handover.
2. Run the BSC6900 MML command SET UHOCOMM (CME single configuration:
UMTS Radio Global Configuration Express > HandOver Parameter
Example
//Activating Intra NodeB Softer Handover
SET UCORRMALGOSWITCH: HoSwitch=HO_INTRA_FREQ_SOFT_HO_SWITCH-1;
SET UHOCOMM: DivCtrlField=MAY;
ADD UINTRAFREQNCELL: RNCId=202, CellId=2381, NCellRncId=203,
NCellId=3291, SIB11Ind=TRUE, SIB12Ind=FALSE, TpenaltyHcsReselect=D0,
NPrioFlag=FALSE;
SET UINTRAFREQHO: FilterCoef=D3, IntraFreqMeasQuantity=CPICH_EC/NO,
PeriodMRReportNumfor1C=D16, ReportIntervalfor1C=D4000;
//Deactivating Intra NodeB Softer Handover
SET UCORRMALGOSWITCH: HoSwitch=HO_INTRA_FREQ_SOFT_HO_SWITCH-0;
This section describes how to activate, verify, and deactivate the basic feature WRFD-020202
Intra RNC Soft Handover.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
Context
Intra-RNC soft handover is one type of soft handover. To implement intra-RNC soft handover,
multiple RLs need to be established between NodeBs or within a NodeB. Intra-NodeB softer
handover and intra-RNC soft handover differ in the place where macro diversity combining is
performed. For intra-RNC soft handover, macro diversity combining, which is in selective mode,
is performed within the RNC. In such a case, each RL on the Iub interface carries transmission
data independently. Compared with intra-NodeB softer handover, the intra-RNC soft handover
can be applied to more scenarios.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to enable soft handover.
2. Run the BSC6900 MML command ADD UINTRAFREQNCELL (CME single
configuration: UMTS Cell Configuration Express > Neighboring Cell > Intra-
frequency Neighboring Cell; CME batch modification center: not supported) to add
an intra-frequency neighboring cell.
3. Run the BSC6900 MML command SET UINTRAFREQHO (CME single
configuration: UMTS Radio Global Configuration Express > HandOver
Example
//Activating Intra RNC Soft Handover
SET UCORRMALGOSWITCH: HoSwitch=HO_INTRA_FREQ_SOFT_HO_SWITCH-1;
ADD UINTRAFREQNCELL: RNCId=202, CellId=2381, NCellRncId=203,
NCellId=3291, SIB11Ind=TRUE, SIB12Ind=FALSE, TpenaltyHcsReselect=D0,
NPrioFlag=FALSE;
SET UINTRAFREQHO: FilterCoef=D3, IntraFreqMeasQuantity=CPICH_EC/NO,
PeriodMRReportNumfor1C=D16, ReportIntervalfor1C=D4000;
//Deactivating Intra RNC Soft Handover
SET UCORRMALGOSWITCH: HoSwitch=HO_INTRA_FREQ_SOFT_HO_SWITCH-0;
This section describes how to activate, verify, and deactivate the optional feature WRFD-020203
Inter RNC Soft Handover.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
l Other Prerequisites
The Iur interface is configured between adjacent RNCs.
Context
Inter-RNC soft handover is one type of soft handover. To implement inter-RNC soft handover,
multiple RLs need to be established between different RNCs. In such a case, macro diversity
combining is performed by the SRNC connected through the Iur interface. The SRNC sends the
DRNC the radio link establishment signaling over the Iur interface. Based on the signaling, the
DRNC establishes a radio link in the new NodeB. Other procedures are similar to those of intra-
RNC soft handover. This feature enables telecom operators to provide seamless connection
services to subscribers. Inter-RNC soft handover has wider application scenario than soft
handover in other forms, as it can be applied to the RNCs connected through the Iur interface.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to enable soft handover.
2. Run the BSC6900 MML command ADD UNRNC (CME single configuration: IUR
Configuration Express > Neighbouring RNC > Neighboring RNC; CME batch
----End
Example
//Activating Inter RNC Soft Handover
SET UCORRMALGOSWITCH: HoSwitch=HO_INTRA_FREQ_SOFT_HO_SWITCH-1;
MOD UNRNC: NRncId=1,
SHOTRIG=CS_SHO_SWITCH-1&HSPA_SHO_SWITCH-1&NON_HSPA_SHO_SWITCH-1;
ADD UEXT3GCELL: NRncId=1, CellId=2381, CellHostType=SINGLE_HOST,
CellName="2222", CnOpGrpIndex=0, PScrambCode=256, BandInd=Band1,
UARFCNUplinkInd=TRUE, UARFCNUplink=9750, UARFCNDownlink=10700,
TxDiversityInd=FALSE, LAC=2506, CfgRacInd=NOT_REQUIRE, QqualminInd=FALSE,
QrxlevminInd=FALSE, MaxAllowedUlTxPowerInd=FALSE, UseOfHcs=NOT_USED,
CellCapContainerFdd=EDCH_SUPPORT-1, EFachSupInd=FALSE;
ADD UINTRAFREQNCELL: RNCId=1, CellId=221, NCellRncId=2, NCellId=222,
SIB11Ind=TRUE, SIB12Ind=FALSE, TpenaltyHcsReselect=D0, NPrioFlag=FALSE;
//Deactivating Inter RNC Soft Handover
MOD UNRNC: NRncId=1,
SHOTRIG=CS_SHO_SWITCH-0&HSPA_SHO_SWITCH-0&NON_HSPA_SHO_SWITCH-0;
This section describes how to activate, verify, and deactivate the optional feature WRFD-020301
Intra Frequency Hard Handover.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
Context
When hard handover is performed, the existing connection is interrupted before new connection
is set up. Intra-frequency hard handover is performed between cells on the same frequency.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to select HO_INTRA_FREQ_HARD_HO_SWITCH from
the HandOver switch list.
2. Run the BSC6900 MML command ADD UINTRAFREQNCELL (CME single
configuration: UMTS Cell Configuration Express > Neighboring Cell > Intra-
frequency Neighboring Cell; CME batch modification center: not supported) to add
an intra-frequency or inter-RNC neighboring cell.
3. If cross-Iur hard handover is required, add the neighboring RNC and neighboring RNC
cell. Run the BSC6900 MML command ADD UNRNC (CME single configuration:
IUR Configuration Express > Neighbouring RNC > Neighboring RNC; CME
batch modification center: not supported) to add a neighboring RNC. Run the
BSC6900 MML command ADD UEXT3GCELL (CME single configuration:
Object Group > UMTS Service Configuration and Maintenance Management >
External Cell Configuration > RNC 3G External Cell; CME batch modification
center: 3.19 Modifying RNC External Cell Parameters in Batches) to add a
neighboring RNC cell. Run the BSC6900 MML command ADD
UINTRAFREQNCELL (CME single configuration: UMTS Cell Configuration
Express > Neighboring Cell > Intra-frequency Neighboring Cell; CME batch
modification center: not supported) to set the neighboring cell relations.
4. Run the BSC6900 MML command SET UINTRAFREQHO (CME single
configuration: UMTS Radio Global Configuration Express > HandOver
Parameter Configuration > RNC Oriented Intra-frequency Handover
Measurement Algorithm Parameters; CME batch modification center: 3.15
Modifying RNC Parameters in Batches) to set the parameter related to handover.
l Verification Procedure
1. On the BSC6900 LMT, click Trace > UMTS Services, and then double-click Uu
Interface Trace. The Uu Interface Trace dialog box is displayed.
2. Set parameters in the areas Cell Config, Uu Message Type, and Save File. Then,
click Submit.
3. Both UE1 and UE2 are subscribed in HLR to support speech service.
4. 4. Both UE1 and UE2 are in idle mode and camp on the CELL1.
5. UE1 calls UE2, and the conversation is clear.
6. UE1 moved from CELL1 to CELL2, through the Trace Date, it can be observed
RRC_MEAS_RPRT message with 1D event that UE1 sends to RNC1.
l Deactivation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to deselect HO_INTRA_FREQ_HARD_HO_SWITCH
from the Handover switch list.
----End
Example
//Activating Intra Frequency Hard Handover
SET UCORRMALGOSWITCH: HoSwitch=HO_INTRA_FREQ_SOFT_HO_SWITCH-1;
ADD UINTRAFREQNCELL: RncId=1, CellId=111, NCellRncId=1, NCellId=211,
SIB11Ind=TRUE, SIB12Ind=FALSE, TpenaltyHcsReselect=D0, NPrioFlag=FALSE;
ADD UNRNC: NRncId =2,
SHOTRIG=CS_SHO_SWITCH-0&HSPA_SHO_SWITCH-0&NON_HSPA_SHO_SWITCH-0,
HHOTRIG=ON, SERVICEIND=SUPPORT_CS_AND_PS, IurExistInd=TRUE, DPX=1,
RNCPROTCLVER=R5, STATEINDTMR=20, TnlBearerType=ATM_TRANS;
ADD UEXT3GCELL: NRncId=2, CellId=311, CellHostType=SINGLE_HOST,
CellName="311", CnOpGrpIndex=0, PScrambCode=256, BandInd=Band1,
UARFCNUplinkInd=TRUE, UARFCNUplink=9750, UARFCNDownlink=10700,
TxDiversityInd=FALSE, LAC=H'2506, CfgRacInd=NOT_REQUIRE,
QqualminInd=FALSE, QrxlevminInd=FALSE, MaxAllowedUlTxPowerInd=FALSE,
CellCapContainerFdd=EDCH_SUPPORT-1, EFachSupInd=FALSE;
ADD UINTRAFREQNCELL: RncId=1, CellId=111, NCellRncId=2, NCellId=311,
SIB11Ind=TRUE, SIB12Ind=FALSE, TpenaltyHcsReselect=D0, NPrioFlag=FALSE;
This section describes how to activate, verify, and deactivate the basic feature WRFD-010801
Intra RNC Cell Update.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
Context
Cell update is mainly used to update the UE information on the network side when the UE
location or behavior is changed. Intra-RNC cell update means cell update within the RNC.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to turn on the RNC-oriented PS BE service state transition
switch.
2. Run the BSC6900 MML command SET UUESTATETRANSTIMER (CME single
configuration: UMTS Radio Global Configuration Express > UE State Transition
Parameter Configuration > RNC StateTrans Timer Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches) to set the
parameters BE DCH to FACH Transition Timer[s] and BE FACH or E_FACH to
PCH Transition Timer[s] to 30s and 60s respectively.
3. Run the BSC6900 MML command SET UPSINACTTIMER (CME single
configuration: UMTS Radio Global Configuration Express > PS Permanent
Online Detection Timer Configuration > PS User Inactive Detecting Timer; CME
2. Log on the BSC6900 LMT, click Trace > UMTS Services, and then double-click
Uu Interface Trace. The Uu Interface Trace dialog box is displayed.
3. Keep the UE in idle mode in CELL1.
4. On the HLR, set the PS service type to background or interactive.
5. Establish an R99 PS service on the UE. The RRC_RB_SETUP message should be
displayed in trace data, and the value of the rrc-stateindicator IE should be
CELL_DCH.
6. Do not send any data from UE for 30 seconds. Then, the network side should perform
UE transition to CELL_FACH state through the RRC_RB_RECFG message, and the
value of the rrc-stateindicator IE should be CELL_FACH.
7. Do not send any data from the UE for five minutes so as to trigger periodic cell update.
The UE should send the RRC_CELL_UPDATE message to the RNC, with the cell
update cause of periodiccellupdate, and the RNC should send the
RRC_CELL_UPDATE_CONFIRM message to the UE.
l Deactivation Procedure
1. None
----End
Example
//Activating intra-RNC cell update
SET UCORRMALGOSWITCH: DraSwitch=DRA_PS_BE_STATE_TRANS_SWITCH-1;
SET UUESTATETRANSTIMER: BeD2FStateTransTimer=30, BeF2PStateTransTimer=60;
SET UPSINACTTIMER: PsInactTmrForInt=0, PsInactTmrForBac=0;
SET UCONNMODETIMER: T305=D5;
This section describes how to activate, verify, and deactivate the basic feature WRFD-010802
Inter RNC Cell Update.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
l Other Prerequisites
The Iur interface is configured between adjacent RNCs.
Context
Cell update is mainly used to update the UE information on the network side when the UE
location or behavior is changed. Inter-RNC cell update means cell update between RNCs.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to turn on the RNC-oriented PS BE service state transition
switch.
2. Run the BSC6900 MML command SET UUESTATETRANSTIMER (CME single
configuration: UMTS Radio Global Configuration Express > UE State Transition
Parameter Configuration > RNC StateTrans Timer Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches) to set the
parameter BE DCH to FACH Transition Timer to 30s.
3. Run the BSC6900 MML command SET UPSINACTTIMER (CME single
configuration: UMTS Radio Global Configuration Express > PS Permanent
Online Detection Timer Configuration > PS User Inactive Detecting Timer; CME
batch modification center: 3.15 Modifying RNC Parameters in Batches) to set
inactivity detection timers for PS services.
4. Configure intra-frequency neighboring cells controlled by different BSC6900s. For
details, see the Configuring an Intra-Frequency Neighboring Cell.
5. Run the BSC6900 MML command MOD UNRNC (CME single configuration: IUR
Configuration Express > Neighbouring RNC > Neighboring RNC; CME batch
modification center: not supported) to set the parameter IUR CCH support flag to
ON.
NOTE
Example
//Activating inter-RNC cell update
SET UCORRMALGOSWITCH: DraSwitch=DRA_PS_BE_STATE_TRANS_SWITCH-1;
SET UUESTATETRANSTIMER: BeD2FStateTransTimer=30;
SET UPSINACTTIMER: PsInactTmrForInt=0, PsInactTmrForBac=0;
MOD UNRNC: NRncId=2, SuppIurCch=YES;
This section describes how to activate, verify, and deactivate the basic feature WRFD-010901
Intra RNC URA Update.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
Context
The UTRAN registration area (URA) update procedure updates the URA of a UE when an RRC
connection exists and the location of the UE is known on the URA level in the UTRAN. Intra-
RNC URA update means URA update within the RNC.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command MOD UCELLACINFO (CME single
configuration: UMTS Cell Configuration Express > Cell Basic Information > Cell
Basic Information; CME batch modification center: not supported) to set CELL1 and
CELL2 as the intra-frequency neighboring cells that belong to the same location area,
route area, and service area.
2. Run the BSC6900 MML command ADD UCELLURA (CME single configuration:
UMTS Cell Configuration Express > Cell Basic Information > Cell URA; CME
batch modification center: not supported) to configure CELL1 and CELL2 to make
them belong to different URAs.
3. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to select DRA_PS_BE_STATE_TRANS_SWITCH from
the Dynamic Resource Allocation Switch drop-down list to turn on the RNC-
oriented PS BE service state transition switch.
4. Optional: Run the BSC6900 MML command SET UCORRMALGOSWITCH
(CME single configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, select the DRA_F2U_SWITCH check box
under the parameter Dynamic Resource Allocation Switch to to enable state
transition from CELL_FACH to URA_PCH directly.
5. Run the BSC6900 MML command SET UUESTATETRANSTIMER (CME single
configuration: UMTS Radio Global Configuration Express > UE State Transition
Parameter Configuration > RNC StateTrans Timer Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches) to set the Cell
Reselection Timer, BE DCH to FACH Transition Timer, and BE FACH or
E_FACH to PCH Transition Timer parameters to 60s, 10s, and 10s respectively.
6. Run the BSC6900 MML command SET UPSINACTTIMER (CME single
configuration: UMTS Radio Global Configuration Express > PS Permanent
Online Detection Timer Configuration > PS User Inactive Detecting Timer; CME
batch modification center: 3.15 Modifying RNC Parameters in Batches) to set
inactivity detection timers for PS services.
7. Run the BSC6900 MML command SET UCONNMODETIMER (CME single
configuration: UMTS Radio Global Configuration Express > UE Timers and
Constants Configuration > UE Timers And Constants in Connected Mode; CME
batch modification center: 3.15 Modifying RNC Parameters in Batches) to set the
periodic cell update timer to 5 minutes.
8. Configure intra-frequency neighboring cells. For details, see the BSC6900 UMTS
Initial Configuration Guide.
l Verifying URA Update Triggered by URA Reselection
1. Log on the BSC6900 LMT, click Trace > UMTS Services, and then double-click
Uu Interface Trace. The Uu Interface Trace dialog box is displayed.
2. Set parameters in the areas Cell Config, Uu Message Type, and Save File. Then,
click Submit.
3. Keep the UE in idle mode in CELL1.
4. On the HLR, set the PS service type to background or interactive.
5. Establish an R99 PS service on the UE. The RRC_RB_SETUP message should be
displayed in trace data, and the value of the rrc-stateindicator IE should be
CELL_DCH.
6. Do not send any data from UE for 30 seconds. Then, the network side should perform
UE transition to CELL_FACH state through the RRC_RB_RECFG message, and the
value of the rrc-stateindicator IE should be CELL_FACH.
7. When the DRA_F2U_SWITCH switch is on or off, the state transition of UE is
different.
If the switch is off: Do not send any data from the UE for another while. Then, the
network side should perform UE transition to CELL_PCH state through the
RRC_RB_RECFG message, and the value of the rrc-stateindicator IE should be
CELL_PCH. Make the UE perform a cell reselection between CELL1 and
CELL2. Make UE1 perform another cell reselection after the Cell Reselection
Example
//Activating intra-RNC URA update
//Configring the cell information
MOD UCELLACINFO: CellId=111, LAC=1, SAC=1, CfgRacInd=REQUIRE, RAC=1;
MOD UCELLACINFO: CellId=121, LAC=1, SAC=1, CfgRacInd=REQUIRE, RAC=1;
ADD UCELLURA: CellId=111, URAId=0;
ADD UCELLURA: CellId=121, URAId=1;
//Enabling status transition (CELL_FACH/CELL_PCH/URA_PCH)
SET UCORRMALGOSWITCH: DraSwitch=DRA_PS_BE_STATE_TRANS_SWITCH-1;
//(Optional) Enabling state transition from CELL_FACH to URA_PCH directly
SET UCORRMALGOSWITCH: DraSwitch=DRA_F2U_SWITCH-1;
//Setting the parameters related to this feature
SET UUESTATETRANSTIMER: BeD2FStateTransTimer=65535,
CellReSelectTimer=180;
SET UUESTATETRANSTIMER: CellReSelectTimer=60, BeD2FStateTransTimer=10,
BeF2PStateTransTimer=10;
SET UUESTATETRANS: CellReSelectCounter=1;
SET UPSINACTTIMER: PsInactTmrForInt=0, PsInactTmrForBac=0;
SET UCONNMODETIMER: T305=D5;
This section describes how to activate, verify, and deactivate the basic feature WRFD-010902
Inter RNC URA Update.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
l Others
The Iur interface is configured between adjacent RNCs.
Context
Inter-RNC URA update means URA update between RNCs.
Procedure
l Activation Procedure
1. Configure the Iur interface. For details, see the BSC6900 UMTS Initial Configuration
Guide.
2. Run the BSC6900 MML command ADD UCELLURA (CME single configuration:
UMTS Cell Configuration Express > Cell Basic Information > Cell URA; CME
batch modification center: not supported) to configure CELL1 and CELL2 to make
them belong to different URAs.
NOTE
Cell1 belongs to RNC_1, Cell2 belongs to RNC_2.
3. On the RNC1 side, run the BSC6900 MML command SET
UCORRMALGOSWITCH (CME single configuration: UMTS Radio Global
Configuration Express > Connection_Oriented RRM Switch Configuration >
Connection Oriented Algorithm Switches; CME batch modification center: 3.15
Example
//Activating inter-RNC URA update
//Configring the cell information
ADD UCELLURA: CellId=111, URAId=0;
ADD UCELLURA: CellId=121, URAId=1;
//Enabling status transition (CELL_FACH/CELL_PCH/URA_PCH)
SET UCORRMALGOSWITCH: DraSwitch=DRA_PS_BE_STATE_TRANS_SWITCH-1;
//(Optional) Enabling state transition from CELL_FACH to URA_PCH directly
SET UCORRMALGOSWITCH: DraSwitch=DRA_F2U_SWITCH-1;
//Setting the parameters related to this feature
SET UUESTATETRANSTIMER: CellReSelectTimer=60, BeD2FStateTransTimer=10,
BeF2PStateTransTimer=10;
SET UUESTATETRANS: CellReSelectCounter=1;
SET UPSINACTTIMER: PsInactTmrForInt=0, PsInactTmrForBac=0;
MOD UNRNC: NRncId=2, SuppIurCch=YES;
MOD UNRNC: NRncId=1, SuppIurCch=YES;
This section describes how to activate, verify, and deactivate the basic feature WRFD-021400
Direct Signaling Connection Re-establishment (DSCR).
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
Context
During a DSCR procedure, the RNC autonomously releases the RRC connection carrying non-
real-time RABs and then immediately requests the UE to re-establish an RRC connection for
service setup. The RRC connection re-establishment procedure is triggered by an RRC
CONNECTION RELEASE message with the cause value of Directed Signaling Connection
re-establishment sent from the RNC to the UE. A routing area update follows the RRC
connection re-establishment immediately.
Only background and interactive services support this feature. The DSCR re-establishes a service
through the routing area update procedure. Therefore, this feature is applicable only to PS
services.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command MOD UNRNC (CME single configuration: IUR
Configuration Express > Neighbouring RNC > Neighboring RNC; CME batch
modification center: not supported). In this step, set Handover Type for PS BE
Traffic to CORRM_SRNSR_PSBE_DSCR.
NOTE
Example
//Activating Direct Signaling Connection Re-establishment (DSCR)
MOD UNRNC: NRncId=20, PsBeProcType=CORRM_SRNSR_PSBE_DSCR;
SET UCORRMALGOSWITCH:
SrnsrSwitch=SRNSR_DSCR_IUR_RESRCE_SWITCH-1&SRNSR_DSCR_LOC_SEPRAT_SWITCH-1
&SRNSR_DSCR_PROPG_DELAY_SWITCH-1&SRNSR_DSCR_SEPRAT_DUR_SWITCH-1;
SET URRCTRLSWITCH: PROCESSSWITCH=DRNC_DIRECT_DSCR-1;
//Deactivating Direct Signaling Connection Re-establishment (DSCR)
MOD UNRNC: NRncId=20, PsBeProcType=CORRM_SRNSR_PSBE_RELOC;
This section describes how to activate, verify, and deactivate the basic feature WRFD-140102
CS Fallback Guarantee for LTE Emergency Calls. For details about how to configure this feature
on the LTE side, see the related documents provided by the LTE equipment vendor.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
l Other Prerequisites
UEs of Release 8 or later support PS handovers from LTE to UMTS and CSFB from
LTE to UMTS. In addition, the message sent to the MME carries an emergency call
indicator.
The eNodeB supports PS handovers from LTE to UMTS and CSFB from LTE to UMTS.
In addition, the handover request sent to the RNC carries CSFB High Priority.
The CN supports PS handovers from LTE to UMTS and CSFB from LTE to UMTS. In
addition, the INITIAL CONTEXT SETUP REQUEST message sent from the MME to
the eNodeB carries CS Fallback High Priority.
Context
In the CS Fall Back (CSFB) process for an LTE emergency call, a UE can initiate an emergency
call on the UMTS network only after the PS service has been admitted to the UMTS network.
This feature ensures the success of PS admission by decreasing the PS service rate or performing
resource preemption.
Procedure
l Activation Procedure
1. Configure the data on the LTE side, including setting the neighbor relationships
between cells.
For details about how to configure this feature on the LTE side, see the related
documents provided by the LTE equipment vendor. If the LTE equipment is provided
by Huawei, see the LTE document CS Fallback Parameter Description.
2. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, select HO_L2U_EMGCALL_SWITCH
under HandOver Switch to enable this feature.
l Verification Procedure
After this feature is activated, the incoming LTE-to-UMTS PS handover success rate caused
by LTE emergency calls increases.
l Deactivation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, clear HO_L2U_EMGCALL_SWITCH under
HandOver Switch to disable this feature.
----End
Example
//Activating CS Fallback Guarantee for LTE Emergency Calls
SET UCORRMALGOSWITCH: HoSwitch= HO_L2U_EMGCALL_SWITCH-1;
//Deactivating CS Fallback Guarantee for LTE Emergency Calls
SET UCORRMALGOSWITCH: HoSwitch= HO_L2U_EMGCALL_SWITCH-0;
This section describes how to activate, verify, and deactivate the basic feature MRFD-210501
NodeB Clock.
Prerequisites
l Dependencies on Hardware
Ensure that a clock link is available before configuring the LINE clock source.
Ensure that the GPS card is configured before configuring the GPS card clock source.
Ensure that the USCU is configured before configuring the BITS clock source.
The BTS3006C and BTS3002E do not support the GPS clock input.
The BTS3902E cannot support GPS and BITS clock.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
Context
In normal operation, the base station needs to track an external clock to calibrate its main clock
frequency. The synchronization of the base station clock provides the basis for the frame
synchronization.
The base station can work in multiple clock synchronization modes:
l Synchronization with the Iub clock (default mode)
l Synchronization with GPS
l Synchronization with the BITS clock
l Synchronization with the IP clock
l Synchronization with the synchronous Ethernet clock (NodeB V200R014)
l Synchronization with the multi-mode sharing clock (NodeB V200R014)
l Synchronization with the PTP clock (NodeB V100R014)
In addition to the preceding synchronization modes, the MBTS internal clock can work in free-
run mode to keep the MBTS running.
Procedure
l NodeB V200R014
Activation Procedure
1. Run the NodeB MML command SET CLKMODE (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Basic Information > Clock
Source > System Clock Link Management; CME batch modification center: not
supported) to set the working mode of the reference clock source.
Verification Procedure
1. Run the NodeB MML command DSP CLKSTAT to query the status of the current
clock source.
Expected result: The value of Current Clock Source State is Normal.
Deactivation Procedure
Activation Procedure
1. Run the NodeB MML command SET CLKMODE (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Basic Information > Clock
Source > System Clock Link Management; CME batch modification center: not
supported) to set the working mode of the reference clock source.
Verification Procedure
1. Run the NodeB MML command DSP CLKSTAT to query the status of the current
clock source.
Expected result: The value of Current Clock Source State is Normal.
Deactivation Procedure
This feature does not need to be deactivated.
----End
Example
l NodeB V200R014
//Activation procedure
//Synchronization with the Iub clock
SET CLKMODE: MODE=MANUAL, CLKSRC=LINECLK;
//Synchronization with the GPS clock
SET CLKMODE: MODE=MANUAL, CLKSRC=GPS, SRCNO=0;
//Synchronization with the BITS clock
SET CLKMODE: MODE=MANUAL, CLKSRC=BITS;
//Synchronization with the IP clock
SET CLKMODE: MODE=MANUAL, CLKSRC=IPCLK;
//Synchronization with the synchronous Ethernet clock
SET CLKMODE: MODE=MANUAL, CLKSRC=SYNCETH;
//Synchronization with the multi-mode sharing clock
SET CLKMODE: MODE=MANUAL, CLKSRC=PEERCLK;
//Verification procedure
DSP CLKSTAT: SN=7;
l NodeB V100R014
//Activation procedure
//Synchronization with the Iub clock
SET CLKMODE: MODE=MANUAL, CLKSRC=LINE;
//Synchronization with the GPS clock
SET CLKMODE: MODE=MANUAL, CLKSRC=GPSCARD;
//Synchronization with the BITS clock
This section describes how to activate, verify, and deactivate the basic feature WRFD-05030104
Dynamic AAL2 Connections in Iub/IuCS/Iur Interface.
Prerequisites
l Dependencies on Hardware
BTS3902E does not support this feature.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
l Others
The RAN is based on ATM transmission.
Context
In ATM transmission mode, the ATM Adaptation Layer type 2 (AAL2) path is used to carry the
user plane data on the Iub/Iur/Iu-CS interface. The AAL2 path is provided according to service
type (conversational, streaming, interactive, and background) and bearer type (R99, HSDPA,
and HSUPA). Physical bandwidth resources are dynamically allocated to delay-sensitive
services and delay-insensitive services, which improves the utilization of transmission links on
the Iub interface.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command ADD ADJNODE (CME single configuration:
NodeB Configuration Express > IUB_RNC > ATM Transport > Adjacent
Node, IUR Configuration Express > ATM Transport > Adjacent Node, IUCS
Configuration Express > ATM Transport > Adjacent Node; CME batch
modification center: not supported) to add an adjacent node. Set the parameter
Adjacent Node Type to IUB, IUR, or IUCS, and the parameter Transport Type to
ATM. If the node is the lowest leaf node of the switching network, set the parameter
Is Root Node to YES; otherwise, set the parameter Is Root Node to NO.
NOTE
For an adjacent node on the Iur or Iu-CS interface, the parameter Adjacent Node Type of its upper-
level hub node must be NNI_AAL2SWITCH; for an adjacent node on the Iub interface, the
parameter Adjacent Node Type of its upper-level hub node must be UNI_AAL2SWITCH.
2. Run the BSC6900 MML command ADD AAL2PATH (CME single configuration:
NodeB Configuration Express > IUB_RNC > ATM Transport > AAL2 Path,
IUCS Configuration Express > ATM Transport > AAL2 Path, IUR
Configuration Express > ATM Transport > AAL2 Path; CME batch modification
center: not supported) to add an AAL2 path. The parameters CARRYVPI and
CARRYVCI must be consistent with those of the AAL2 path configured on the peer
end.
l Verification Procedure
1. Run the BSC6900 MML command DSP AAL2PATH to query the status of the AAL2
path on the Iub interface.
Expected result: The value of Operation state is Available.
2. In the Iub/Iu-CS ATM transmission scenario, a UE in idle state camps on CELL1 and
the control plane is correctly configured. Originate the speech and data services. If the
service access is normal, the AAL2 path on the Iub/Iu-CS interface is set up
successfully.
3. Optional: In the ATM transmission scenario on the Iur interface, a UE in idle state
camps on CELL1 and the control plane is correctly configured. Originate a cross-Iur
handover. If the handover is successful, the AAL2 path on the Iur interface is set up
successfully.
l Deactivation Procedure
This feature does not need to be deactivated.
----End
Example
//Activating Dynamic AAL2 Connections in Iub/IuCS/Iur Interface
//Adding an adjacent node
ADD ADJNODE: ANI=2, NAME="MSC1", NODET=IUCS, TRANST=ATM, IsROOTNODE=YES,
DPX=1;
//Adding an AAL2 path
ADD AAL2PATH: ANI=2, PATHID=1, CARRYT=UNI, CARRYF=1, CARRYSN=14,
CARRYUNILNKN=0, RSCGRPFLAG=NO, VPI=12, VCI=126, TXTRFX=111, RXTRFX=111,
AAL2PATHT=R99;
This section describes how to activate, verify, and deactivate the basic feature WRFD-05030105
Permanent AAL5 Connections for Control Plane Traffic.
Prerequisites
l Dependencies on Hardware
BTS3902E does not support this feature.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
l Others
The equipment data has been configured for the ATM transmission on the Iub/Iu/Iur
interface.
NOTE
For details about how to configure the equipment data, see section Configuring the Equipment
Data of the BSC6900UMTS Initial Configuration Guide.
Context
In the RAN in ATM transmission mode, AAL5 connections are used to bear the Iub/Iur/Iu
signaling and the Iub OAM traffic. As specified by 3GPP, User-Network Interface SAAL (UNI-
SAAL) is used for control-plane connections on the Iub interface and Network-Network
Interface SAAL (NNI-SAAL) is used for control-plane connections on the Iur/Iu interface.
AAL5 connections on the Iub/Iur/Iu interface are all set up by configuring Signaling ATM
adaptation layer (SAAL) links.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command ADD SAALLNK (CME single configuration:
NodeB Configuration Express > IUB_RNC > ATM Transport > SAAL Signaling
Link, IUCS Configuration Express > ATM Transport > SAAL Signaling Link,
IUR Configuration Express > ATM Transport > SAAL Signaling Link; CME
batch modification center: not supported) to add an SAAL link. If the interface is Iub,
set the parameter Interface type to UNI. If the interface is Iu or Iur, set Interface
type to NNI.
2. Optional: Run the BSC6900 MML command ADD UNCP (CME single
configuration: NodeB Configuration Express > IUB_RNC > ATM Transport >
NCP Link; CME batch modification center: not supported) to add a NodeB Control
Port (NCP) link.
3. Optional: Run the BSC6900 MML command ADD UCCP (CME single
configuration: NodeB Configuration Express > IUB_RNC > ATM Transport >
CCP Link; CME batch modification center: not supported) to add a Communication
Control Port (CCP) link.
NOTE
An SAAL link can carry only one NCP or CCP link. Therefore, choose to perform step 2 or
step 3 based on the actual situation.
l Verification Procedure
1. Run the BSC6900 MML command DSP SAALLNK to query the status of the SAAL
link.
Expected result: The value of SAAL link state is AVAILABLE.
l Deactivation Procedure
NOTE
An SAAL link can carry only one NCP or CCP link. Therefore, choose to remove the NCP or CCP
link carried by the SAAL link, based on the actual situation.
1. Optional: Run the BSC6900 MML command RMV UNCP (CME single
configuration: NodeB Configuration Express > IUB_RNC > ATM Transport >
NCP Link; CME batch modification center: not supported) to remove the NCP link
carried by the SAAL link.
2. Optional: Run the BSC6900 MML command RMV UCCP (CME single
configuration: NodeB Configuration Express > IUB_RNC > ATM Transport >
CCP Link; CME batch modification center: not supported) to remove the CCP link
carried by the SAAL link.
3. Run the BSC6900 MML command RMV SAALLNK (CME single configuration:
NodeB Configuration Express > IUB_RNC > ATM Transport > SAAL Signaling
Link, IUCS Configuration Express > ATM Transport > SAAL Signaling Link,
IUR Configuration Express > ATM Transport > SAAL Signaling Link; CME
batch modification center: not supported) to remove the SAAL link.
----End
Example
//Activating Permanent AAL5 Connections for Control Plane Traffic
ADD SAALLNK: SRN=1, SN=2, SAALLNKN=10, CARRYT=UNI, CARRYSRN=0,
CARRYSN=14, CARRYUNILNKN=2, CARRYVPI=10, CARRYVCI=55, TXTRFX=100,
RXTRFX=100, SAALLNKT=UNI;
ADD UCCP: NODEBNAME="NodeB1", PN=0, CARRYLNKT=SAAL, SAALLNKN=10;
//Verifying Permanent AAL5 Connections for Control Plane Traffic
DSP SAALLNK: SRN=1, SN=2, SAALLNKN=10;
//Deactivating Permanent AAL5 Connections for Control Plane Traffic
RMV UCCP: NODEBNAME="NodeB1", PN=0;
RMV SAALLNK: SRN=1, SN=2, SAALLNKN=10;
This section describes how to activate, verify, and deactivate the basic feature WRFD-05030106
Call Admission Based on Used AAL2 Path Bandwidth.
Prerequisites
l Dependencies on Hardware
BTS3902E does not support this feature.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
Context
With the Call Admission Based on Used AAL2 Path Bandwidth (AAL2 CAC) feature, admission
requests are accepted or rejected selectively. This feature maximizes the usage of transmission
resources in addition to ensuring the QoS.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command ADD ATMTRF (CME single configuration:
NodeB Configuration Express > IUB_RNC > ATM Transport > ATM Traffic
Record; CME batch modification center: not supported) to set parameters to
appropriate values. For example, set Service type to NRTVBR, Peak cell rate to
100, and Sustainable cell rate to 80.
2. Run the BSC6900 MML command ADD AAL2PATH (CME single configuration:
NodeB Configuration Express > IUB_RNC > ATM Transport > AAL2 Path;
CME batch modification center: not supported) to add an ATM Adaptation Layer type
2 (AAL2) path. In this step, set TXTRFX and RXTRFX in accordance with the
settings in step 1.
l Verification Procedure
1. Assume that the verification is based on the preceding parameter settings and the peer
end is configured with the corresponding AAL2 path link. Originate a PS interactive
service. If the data rate is 64 kbit/s, the UE successfully accesses the network.
2. Run the BSC6900 MML command DSP AAL2PATH to view that the used bandwidth
of the path is about 37 kbit/s, which is the admission bandwidth of the control plane.
3. Originate a PS interactive service. If the data rate is 128 kbit/s, the UE fails to access
the network.
l Deactivation Procedure
This feature does not need to be deactivated.
----End
Example
//Activation procedure
ADD ATMTRF: TRFX=100, ST=NRTVBR, UT=CELL/S, PCR=100, SCR=80;
ADD AAL2PATH: ANI=0, PATHID=10, CARRYT=UNI, CARRYF=1, CARRYSN=14,
CARRYUNILNKN=0, RSCGRPFLAG=NO, VPI=12, VCI=126, TXTRFX=100, RXTRFX=100,
AAL2PATHT=R99;
This section describes how to activate, verify, and deactivate the basic feature
"WRFD-05030107 CBR, rt-VBR, nrt-VBR, UBR ATM QoS Classes".
Prerequisites
l Dependencies on Hardware
BTS3902E does not support this feature.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
Context
Huawei RAN supports service type of ATM :
l Constant Bit Rate (CBR)
l Real time Variable Bit Rate (rt-VBR)
l Non-real time Variable Bit Rate (nrt-VBR)
l Unspecified Bit Rate (UBR)
l Enhanced unspecified Bit Rate (UBR+)
Configuring UBR+ QoS Class feature, please refer to Configuring UBR+ ATM QoS Class.
The traffic volume on the VCC depends on the parameters (SCR, PCR, and CDVT) associated
with each type of ATM service. Generally, rt-VBR is applicable to delay-sensitive services and
nrt-VBR is applicable to delay-insensitive services. In addition, UBR and nrt-VBR are applicable
to None Delay Sensitive service mapping on the HSDPA/HSUPA.
It is recommended for configuring service type of ATM shown as Figure 46-1.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command ADD ATMTRF (CME single configuration:
NodeB Configuration Express > IUB_RNC > ATM Transport > ATM Traffic
Record; CME batch modification center: not supported) to add an ATM traffic record.
To add more ATM traffic records, run this command repeatedly.
l Verification Procedure
1. Run the BSC6900 MML command LST ATMTRF to query the ATM traffic
configuration. The expected result is that the query result is consistent with the
configuration information.
l Deactivation Procedure
1. Run the BSC6900 MML command RMV ATMTRF (CME single configuration:
NodeB Configuration Express > IUB_RNC > ATM Transport > ATM Traffic
Record; CME batch modification center: not supported) to delete an ATM traffic
record. To delete more ATM traffic records, run this command repeatedly.
----End
Example
//Activating CBR, rt-VBR, nrt-VBR, UBR ATM QoS Classes
ADD ATMTRF: TRFX=105, ST=CBR, UT=CELL/S, PCR=1000;
//Verifying CBR, rt-VBR, nrt-VBR, UBR ATM QoS Classes
LST ATMTRF: TRFX=105;
Deactivating CBR, rt-VBR, nrt-VBR, UBR ATM QoS Classes
RMV ATMTRF: TRFX=105;
47 Configuring F5
This section describes how to activate, verify, and deactivate the basic feature WRFD-05030110
F5. (This feature cannot be configured using the CME. )
Prerequisites
l Dependencies on Hardware
VCL CC is applicable to the AEUa, AOUa, AOUc, UOIa(ATM), and UOIc boards of
the BSC6900.
VCL PM is applicable to the AOUc and UOIc boards of the BSC6900.
Only BSC6900 does not support the latency detection based on IE LB.
Only 3900 series Base Station supports the passive detection based on IE LB.
BTS3902E does not support this feature.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
Context
This feature supports:
l ATM CC provides E2E continuity detection on the VCL.
l PM function provides performance monitoring on the VCL.
l It is recommended to activate VCL CC before activating VCL PM.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command ACT VCLCC to activate the VCL CC or loopback
function for a link. To activate the function for multiple links, run this command
repeatedly. There are three types of links, that is, SAALLNK, AAL2PATH, and
IPOAPVC.
2. Run the BSC6900 MML command ACT VCLPM to activate the VCL PM function
for a link. To activate the function for multiple links, run this command repeatedly.
There are three types of links, that is, SAALLNK, AAL2PATH, and IPOAPVC.
l Verification Procedure
1. Run the BSC6900 MML command DSP VCLCC to query the CC result of a VCL.
If the VCL CC is activated and the PVC is functional, the SINK activated state
and SOURCE activated state are UP, and LOC, AIS, and RDI alarm state is
normal.
If the loopback is activated and the PVC is functional, the loopback query result
is UP, and LOC, AIS, and RDI alarm state is normal.
2. Run the BSC6900 MML command DSP VCLPM to query the PM result of a VCL.
If the VCL PM is activated, the SINK activated state and SOURCE activated
state are PM_UP, and PM Active Fail Alarm is Normal.
l Deactivation Procedure
1. Run the BSC6900 MML command DEA VCLCC to deactivate the VCL CC or
loopback function for a link. To deactivate the function for multiple links, run this
command repeatedly. There are three types of links, that is, SAALLNK, AAL2PATH,
and IPOAPVC.
2. Run the BSC6900 MML command DEA VCLPM to deactivate the VCL PM for a
link. To deactivate the function for multiple links, run this command repeatedly. There
are three types of links, that is, SAALLNK, AAL2PATH, and IPOAPVC.
----End
Example
//Activating F5
ACT VCLCC: LNKT=SAALLNK, SRN=3, SN=2, SAALLNKN=0, VCLTYPE=CC;
ACT VCLPM: LNKT=SAALLNK, SRN=3, SN=2, SAALLNKN=0;
//Verifying F5
DSP VCLCC: LNKT=SAALLNK, SRN=3, SN=2, SAALLNKN=0;
DSP VCLPM: LNKT=SAALLNK, SRN=3, SN=2, SAALLNKN=0;
//Deactivating F5
DEA VCLCC: LNKT=SAALLNK, SRN=3, SN=2, SAALLNKN=0;
DEA VCLPM: LNKT=SAALLNK, SRN=3, SN=2, SAALLNKN=0;
This section describes how to activate, verify, and deactivate the basic feature "WRFD-050305
UBR+ ATM QoS Class".
Prerequisites
l Dependencies on Hardware
BTS3902E does not support this feature.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
l Other Prerequisites
The basic information about the BSC6900 is configured. For details, see the Configuring
the Basic Data.
Context
Huawei RAN supports the UBR+ ATM service class. UBR+ is the enhanced UBR feature. It
adds the Minimum Desired Cell Rate (MDCR) indication. UBR+ is particularly applicable to
the OAM channels over the Iub interface. The MDCR of UBR+ ensures the reliability of the
OAM connection in case of transmission channel congestion, and the BE service of the UBR+
fully utilizes transmission bandwidth.
Procedure
l Activation Procedure
1. Run the MML command ADD ATMTRF (CME single configuration: NodeB
Configuration Express > IUB_RNC > ATM Transport > ATM Traffic Record;
CME batch modification center: not supported) to add an ATM traffic record of the
UBR+ class. To add more ATM traffic records, run this command repeatedly.
l Verification Procedure
1. Run the MML command LST ATMTRF to query the ATM traffic configuration.
Expected result: The query result is consistent with the configuration information.
l Deactivation Procedure
1. Run the MML command RMV ATMTRF (CME single configuration: NodeB
Configuration Express > IUB_RNC > ATM Transport > ATM Traffic Record;
CME batch modification center: not supported) to delete an ATM traffic record of the
UBR+ class. To delete more ATM traffic records, run this command repeatedly.
----End
Example
//Adding UBR+ ATM QoS Class
ADD ATMTRF: TRFX=105, ST=UBR_PLUS, UT=CELL/S, MCR=100;
//Verifying UBR+ ATM QoS Class
LST ATMTRF: TRFX=105;
//Deactivating UBR+ ATM QoS Class
RMV ATMTRF: TRFX=105;
This section describes how to activate, verify, and deactivate the basic feature MRFD-210103
Link Aggregation.
Prerequisites
l Dependencies on Hardware
This feature applies only to 3900 series base stations excluding the BTS3902E.
This feature is only supported on BSC6900.
l Dependencies on Other Features
In the earlier versions than RAN13.0, trunk group configuration cannot support IP PM.
l License
This feature is not under license control.
l Others
This feature requires the support from peer transmission devices, such as switches and
base stations.
This feature supports IP networking, layer 2 (L2) networking, and layer 3 (L3)
networking.
Context
This feature enables multiple FE or GE ports to be bound to form a logical port. This provides
high bandwidth for end-to-end transmission, achieves load sharing across these FE or GE ports,
and improves the transmission reliability.
Procedure
l Activation Procedure
Activate Link Aggregation on the BSC6900.
1. Run the BSC6900 MML command ADD DEVIP (CME single configuration:
Abis Configuration Express > IP Transport > Device IP Address; CME batch
modification center: not supported) to add a device IP address to a board.
2. Run the BSC6900 MML command ADD ETHTRK (CME single configuration:
Abis Configuration Express > IP Transport > Link Aggregation; CME batch
modification center: not supported) to add an Ethernet link aggregation group. In
Expected result: If the value of Status of ETHTRK is UP in the command output, the Ethernet
link aggregation group is available.
2. Set the IP address of the peer NE to be on the same network segment as the IP
address for the Ethernet link aggregation group. For example, set the IP address
of the peer NE to 16.16.16.2.
3. Run the BSC6900 MML command PING IP to check the IP communication
between the local and peer ends.
NOTE
Expected result: If this command is executed and the command output indicates that no packet
loss occurs, the Ethernet link aggregation group has been successfully configured.
Verify the effect of Link Aggregation on the NodeB.
1. Run the NodeB MML commandDSP ETHTRK to query whether an Ethernet link
aggregation group is available.
2. Run the NodeB MML commandDSP ETHTRKLNK to query whether a member
port of an Ethernet link aggregation group is available.
l Deactivation Procedure
Deactivate Link Aggregation on the BSC6900.
1. Run the BSC6900 MML commandRMV ETHTRKIP (CME single
configuration: Abis Configuration Express > IP Transport > Trunk IP
Address; CME batch modification center: not supported) to remove an IP address
from an Ethernet link aggregation group. If the removal fails, perform operations
as prompted.
2. Run the BSC6900 MML commandRMV ETHTRK (CME single configuration:
Abis Configuration Express > IP Transport > Link Aggregation; CME batch
modification center: not supported) to remove an Ethernet link aggregation group.
Deactivate Link Aggregation on the NodeB.
1. Run the NodeB MML commandRMV DEVIP (CME single configuration: NodeB
Configuration Express > IUB_NodeB > IP Transport Layer > IPPort > Device
IP Address; CME batch modification center: not supported) to remove a device
IP address.
2. Run the NodeB MML commandRMV ETHTRK (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer >
IPPort > Ethernet Trunk; CME batch modification center: not supported) to
remove an Ethernet link aggregation group.
----End
Example
//Activating Link Aggregation on the BSC6900
ADD DEVIP: SRN=2, SN=26, DEVTYPE=LOGIC_IP, IPADDR="10.171.35.123";
ADD ETHTRK: SRN=2, SN=26, TRKN=2, WORKMODE=ACTIVE_STANDBY,
LACPMODE=MANUAL_AGGREGATION, FLOWCTRLSWITCH=ON;
ADD ETHTRKLNK: SRN=2, SN=26, TRKN=2, TRKLNKSN=26, TRKLNKPN=2,
WORKMODE=ACTIVE_STANDBY, PORTPRI=101;
ADD ETHTRKLNK: SRN=2, SN=26, TRKN=2, TRKLNKSN=27, TRKLNKPN=2,
WORKMODE=ACTIVE_STANDBY, PORTPRI=102;
ADD ETHTRKIP: SRN=2, SN=26, TRKN=2, IPINDEX=0, IPADDR="126.126.126.1",
MASK="255.255.255.0";
This section describes how to activate, verify, and deactivate the basic feature WRFD-040100
Flow Control.
Prerequisites
l Dependencies on Hardware
NodeB RRC link priority based flow control is depended on WMPT and WBBP boards.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
Context
Flow control is implemented by regulating the input transmission rate. This mechanism is called
feedback flow control mechanism.
The flow control measures are as follows:
l Board flow control
l Control-plane load sharing
l User-plane load sharing
l Flow control based on RRC request queuing
l Flow control based on MPU load
l Flow control based on traffic growth
Procedure
l Activation Procedure
Activating board flow control
1. Run the BSC6900 MML command SET FCSW (CME single configuration:
UMTS Radio Global Configuration Express > Flow Control Management >
Flow Control Switch; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to switch on the flow control and related flow control
items.
l Flow control is triggered when the CPU usage exceeds the related threshold.
l The CPU usage thresholds must meet the following condition: 100 Critical threshold
Threshold for a flow control item Restore threshold for a flow control item
l The critical threshold is of the highest priority. That is, other thresholds take effect only
when the CPU usage is lower than the critical threshold.
l The flow control based on the packet usage and that based on the CPU usage are independent.
The system limits the flow to the lower one allowed by these two flow control algorithms.
3. Run the BSC6900 MML command SET FCMSGQTHD (CME single
configuration: UMTS Radio Global Configuration Express > Flow Control
Management > Flow Control Threshold of Message Queue Usage; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches) to configure
the packet usage threshold for each flow control item according to the network
plan.
NOTE
l Flow control is triggered when the packet usage exceeds the related threshold.
l The packet usage thresholds must meet the following condition: 100 Critical threshold
Threshold for a flow control item Restore threshold for a flow control item
l The critical threshold is of the highest priority. That is, other thresholds take effect only
when the packet usage is lower than the critical threshold.
l The flow control based on the packet usage and that based on the CPU usage are independent.
The system limits the flow to the lower one allowed by these two flow control algorithms.
Activating control-plane load sharing
1. Run the BSC6900 MML command SET URRCTRLSWITCH (CME single
configuration: UMTS Radio Global Configuration Express > Process Switch
Configuration > Process Switch; CME batch modification center: 3.15
Modifying RNC Parameters in Batches). In this step, set Process switch to
RNC_SHARE_SWITCH to switch on load sharing.
2. (Optional) Run the BSC6900 MML command SET
UCTRLPLNSHAREPARA (CME single configuration: UMTS Radio Global
Configuration Express > Flow Control Management > Control Plane RRC
Sharing Parameter; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, set Control Plane Sharing Out
Threshold to 40 so that the control-plane load sharing function can be triggered
easily. The default value of Control Plane Sharing Out Threshold is 50.
NOTE
l If the CPU usage is higher than this threshold and lower than the overload threshold, new
calls will be assigned to other SPUs. Overload threshold is set by the MML command SET
SHARETHD (CME single configuration: UMTS Radio Global Configuration Express
> Flow Control Management > Load Sharing Threshold of SPU Board; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches).
l Max capability middle load> Max capability normal load> Sharing out capability
middle load.
Activating user-plane load sharing
Example
//Activating board flow control
//Switching on XPU load control
SET FCSW: BRDCLASS=XPU, FCSW=ON, PRINTSW=ON, TRACESW=ON, PMSW=ON,
LOGSW=ON;
//Setting CPU usage threshold for DPU flow control
SET FCCPUTHD:BRDCLASS=DPU, SMWINDOW=6, FDWINDOW=2, CTHD=95, PRINTCTHD=60,
PRINTRTHD=50, TRACECTHD=60, TRACERTHD=50, LOGCTHD=60, LOGRTHD=50;
//Setting packet usage threshold for DPU flow control
SET FCMSGQTHD: BRDCLASS=DPU, SMWINDOW=9, CTHD=95, PRINTCTHD=60,
PRINTRTHD=50, TRACECTHD=60, TRACERTHD=50, LOGCTHD=60, LOGRTHD=50;
51 Configuring BOOTP
This section describes how to activate, verify, and deactivate the basic feature WRFD-031100
BOOTP. In ATM transport mode, the NodeB can automatically set up the OM channel with the
BSC6900 by using the BOOTSTRAP Protocol (BOOTP) function.
Prerequisites
l Dependencies on Hardware
The transmission equipment is in the connected state.
BOOTP applies only to ATM networking scenarios.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
Context
This feature enables NodeB to set up the OM channel to the RNC automatically without
configuration data. The maintenance staff can download the data and software to the NodeB
through the OM channel at the far end. The feature decreases the operation and maintenance
costs and enhances the network maintainability and maintenance quality. NodeB will
automatically set up the OM channel using the BOOTP protocol. In addition, NodeB monitors
the OM channel. When the OM channel is broken, NodeB can rebuild it.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command ADD DEVIP (CME single configuration: NodeB
Configuration Express > IUB_RNC > ATM Transport > Device IP Address;
CME batch modification center: not supported) to add the logical IP address for the
interface board of the BSC6900. This IP address serves as the local address of the
IPoA at the BSC6900.
2. Run the BSC6900 MML command ADD IPOAPVC (CME single configuration:
IUPS Configuration Express > ATM Transport > IPoA PVC; CME batch
modification center: not supported) to add the IPoA PVC for bearing the OM channel.
3. Run the BSC6900 MML command ADD UNODEBIP (CME single configuration:
NodeB Configuration Express > IUB_RNC > ATM Transport > NodeB IP
Address; CME batch modification center: not supported) to add the IP address for the
OM channel of the NodeB.
l Verification Procedure
If the BOOTP configurations at the BSC6900 are completed but no configuration at the
NodeB and the NodeB can be maintained on the M2000, it indicates that the NodeB has
successfully set up the OM channel by using the BOOTP feature.
l Deactivation Procedure
This feature does not need to be deactivated.
----End
Example
//Activation procedure
ADD DEVIP: SRN=0, SN=14, DEVTYPE=IPOA_CLIENT_IP,
IPADDR="131.131.131.132", MASK="255.255.255.0";
ADD IPOAPVC: IPADDR="131.131.131.132", PEERIPADDR="131.131.131.131",
CARRYT=IMA,
CARRYIMAGRPN=0, CARRYVPI=83, CARRYVCI=80, TXTRFX=100;
ADD UNODEBIP: NODEBID=0, NBTRANTP=ATMTRANS_IP,
NBATMOAMIP="131.131.131.131",
NBATMOAMMASK="255.255.255.0", ATMSRN=0, ATMSN=14;
This section describes how to activate, verify, and deactivate the basic feature WRFD-031101
NodeB Self-Discovery Based on IP Mode.
Prerequisites
l Dependencies on Hardware
The transmission equipment is in the connected state.
DHCP applies only to IP networks.
Only 3900 series base stations support DHCP+AACP.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
l Others
If NodeB self-discovery uses the DHCP+AACP scheme
VLANs are used to separate NodeBs to be deployed from other network devices not
required.
VLAN detection and IP path detection must be disabled on the M2000 to prevent
interference during AACP detection.
the deployment list of NodeBs to be commissioned must be ready. For details, see
the NodeB Commissioning Guide.
A bidirectional forwarding detection (BFD) session failure results in a NodeB
automatic deployment failure. Therefore, the BFD function must be disabled on the
gateway side if it is enabled on the NodeB side.
The IP path ping function must be disabled on the RNC side during NodeB automatic
deployment. Otherwise, when the ping message sent by the RNC reaches the
gateway, the gateway sends an ARP request to the NodeB, disturbing the AACP
detection process and resulting in a NodeB automatic deployment failure.
AACP and DHCP messages can be processed through port 67 or 68. Ports 67 and 68
must be enabled for the firewall in the radio network.
Context
l If the configuration file is incorrect, DHCP enables NodeBs to establish OM channels for
NodeB remote maintenance.
l The configuration is not required on the NodeB. If the hub NodeB is used, the configuration
on the hub NodeB is required. The configuration is required on the DHCP server, for
example, BSC6900 and M2000. Following takes BSC6900 for example.
l Data Preparation
PPP/MLPPP networking
Ethernet networking
Procedure
l Activation Procedure (NodeB Self-Discovery Based on DHCP)
1. Run the BSC6900 MML command ADD UNODEBESN (CME single configuration:
NodeB Configuration Express > IUB_RNC > IP Transport > NodeB Electronic
Serial Number; CME batch modification center: not supported) to add the NodeB
ESN in response to the DHCP request reported by the NodeB.
2. Run the BSC6900 MML command ADD UNODEBIP (CME single configuration:
NodeB Configuration Express > IUB_RNC > IP Transport > NodeB IP
Address; CME batch modification center: not supported) to add the IP address for the
OM channel of the NodeB. When the BSC6900 makes a response to the DHCP
request, it sends the IP address to the NodeB.
3. Optional: If the Hub NodeB is used and the DHCP function is used for NodeB self-
discovery, the following configurations are required.
a. Run the NodeB MML command SET DHCPRELAYSWITCH (CME single
configuration: NodeB Configuration Express > IUB_NodeB > Basic
Information > Transport Management > DHCP Relay Switch; CME batch
modification center: not supported) to enable DHCP relaying of the NodeB.
b. Run the NodeB MML command ADD DHCPSVRIP (CME single
configuration: NodeB Configuration Express > IUB_NodeB > Basic
Information > Transport Management > DHCP Server IP Address; CME
batch modification center: not supported) to add the IP address of the DHCP
server so that lower-level NodeBs can automatically obtain the IP address of the
DHCP server through DHCP.
l Activation Procedure (NodeB Self-Discovery Based on DHCP+AACP)
1. Optional: Run the NodeB MML command SET NODEBRSVP (CME single
configuration: NodeB Configuration Express > IUB_NodeB > Basic
Information > Radio Management > NodeB Reserved Para; CME batch
modification center: not supported). In this step, select RSVDBIT29(Reserved
Switch 29) under Reserved Parameter 1.
2. On the M2000 client, Choose Configuration > Auto Deployment > NodeB Auto
Deployment. Right-click the import the deployment list, and choose Task Setting
from the shortcut menu. The Task Settings dialog box is displayed.
3. Select Use AACP during Auto Discovery to use AACP for NodeB automatic
deployment, Click OK to start NodeB automatic deployment.
l Verification Procedure
Check the status of NodeB automatic deployment in either of the following ways:
On the deployment list of the M2000
1. Click Show Executing Information on the Deployment List tab page.
2. View the information displayed in the Description column. If Execution
Succeed is displayed, AACP-based NodeB automatic deployment is successful.
Example
//Activation procedure
//NodeB Self-Discovery Based on DHCP
//Operations on the BSC6900 side
ADD UNODEBESN: NODEBID=0, NBLB1="020GKV1082000126", USENBLB2=Disable,
NODEBPT=ETH/TRUNK, PTIP="131.131.131.132", PTIPMASK="255.255.255.0";
ADD UNODEBIP: NODEBID=0, NBTRANTP=IPTRANS_IP,
NBIPOAMIP="131.131.131.131", NBIPOAMMASK="255.255.255.0", IPSRN=0,
IPSN=18, IPLOGPORTFLAG=NO;
//Deactivation procedure
SET NODEBRSVP: REVDPARA1=RSVDBIT29-0;
This section describes how to activate, verify, and deactivate the basic feature WRFD-040300
License Control for Urgency. (This feature cannot be configured using the CME. )
Prerequisites
l Dependencies on Hardware
Only BSC6900 supports this feature.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
Context
CAUTION
This feature is enabled only in scenarios where the traffic volume increases abruptly, for
example, in a disaster.
It can be enabled only three times for each R version by BSC6900 MML command SET
LICENSECTRL and it can be enabled only fifteen times by WRFD-040202 RNC Node
Redundancy and it is valid only for seven days each time.
After this function is enabled, a network can reach its maximum capacity that is supported by
the hardware. This documentation describes the procedure of enabling the feature by
BSC6900 MML command .
Procedure
l Activation Procedure
1. On the BSC6900 side: Run the BSC6900 MML command SET LICENSECTRL. In
this step, set Grace Protection Period Switch to ON(ON).
2. On the NodeB V200R014 side: Run the NodeB MML command SET
LICENSECTRL. In this step, set Grace Protection Period Switch State to ON.
3. On the NodeB V100R014 side: Run the NodeB MML command SET
LICENSECTRL. In this step, set Grace Protection Period Switch to ON(ON).
l Verification Procedure
1. On the BSC6900 Side
a. Run the BSC6900 MML command DSP LICUSAGE to view resource items of
the license.
Expected result: All the resource items reach their maximum values.
b. Run the BSC6900 MML command LST LICENSECTRL to query the setting
of Grace Protection Period Switch State.
Expected result: Values of Remaining Grace Protection Times and Remaining
Grace Protection Days are displayed and the value of Grace Protection Period
Switch State is ON.
2. On the NodeB V200R014 side or NodeB V100R014 side
a. Run the NodeB MML command DSP LICENSE to view resource items of the
license.
Expected result: All the resource items reach their maximum values.
b. Run the NodeB MML command LST LICENSECTRL to query the setting of
Grace Protection Period Switch State.
Expected result: Values of Remaining Grace Protection Times and Remaining
Grace Protection Days are displayed and the value of Grace Protection Period
Switch State is ON.
l Deactivation Procedure
1. On the BSC6900 Side: Run the BSC6900 MML command SET LICENSECTRL.
In this step, set Grace Protection Period Switch to OFF(OFF).
2. On the NodeB V200R014 Side: Run the NodeB MML command SET
LICENSECTRL. In this step, set Grace Protection Period Switch State to OFF.
3. On the NodeB V100R014 Side: Run the NodeB MML command SET
LICENSECTRL. In this step, set Grace Protection Period Switch to OFF(OFF).
----End
This section describes how to activate, verify, and deactivate the basic feature WRFD-031000
Intelligently Out of Service.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
Context
Insufficient battery voltage or NodeB reset may lead to service disruption. When the preceding
problems occur, this feature enables the NodeB to automatically reduce the pilot transmit power
and hand over the UE to other cells, preventing service disruption.
Procedure
l Activation Procedure
1. Run the NodeB MML command SET SMTHPWRSWTCH (CME single
configuration: NodeB Configuration Express > IUB_NodeB > Basic
Information > Basic Information > Smooth Power Change Function Switch;
CME batch modification center: not supported). In this step, set Smooth Power
Change Function Switch to OPEN(Open).
2. Run the NodeB MML command SET SMTHPWRPARA (CME single
configuration: NodeB Configuration Express > IUB_NodeB > Basic
Information > Basic Information > Smooth Power Change Function Switch;
CME batch modification center: not supported). In this step, set Smart default step
(0.5dB) and Smart default time ratio(100ms).
l Verification Procedure
1. Run the NodeB MML command LST SMTHPWRSWTCH. In this step, check
whether Smooth Power Change Function Switch is set to OPEN.
2. Run the NodeB MML command LST SMTHPWRPARA. In this step, check whether
Smart default step(0.5dB) and Smart default time ratio(100ms) are set correctly.
l Deactivation Procedure
This feature does not need to be deactivated.
----End
Example
//Activation procedure
SET SMTHPWRSWTCH: SWITCH=OPEN;
SET SMTHPWRPARA: STEP=10, PERIOD=1;
//Verification procedure
LST SMTHPWRSWTCH:;
LST SMTHPWRPARA:;
55 Configuring OCNS
This section describes how to activate, verify, and deactivate the basic feature WRFD-031200
OCNS (Orthogonal Channel Noise Simulator). (This feature cannot be configured using the
CME. )
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
Context
With the OCNS feature, multiple downlink analog channels are set up on the Uu interface to
simulate the interference of multiple codes. In this way, the simulated downlink load test of a
cell can be performed.
Procedure
l Activation Procedure
1. Run the NodeB MML command STR DLSIM to start downlink load simulation. In
this step, set Local Cell ID and Load Ratio (%).
NOTE
l This command can be successfully executed only when the corresponding logical cell exists.
l The downlink network load simulation uses the channelization codes from 112 to 127 whose
SF = 128.
l If you start the downlink network load simulation, it is advised to reserve the channelization
codes in the RNC.
l After starting the DL load simulation, new service can not be built in the channel resource
occupied by the simulation.
l Verification Procedure
1. Run the NodeB MML command DSP DLSIM to query the downlink load simulation
result. In this step, specify Local Cell ID. The execution result displayed on the LMT
shows the simulated load rate.
l Deactivation Procedure
1. Run the NodeB MML command STP DLSIM to stop the downlink load simulation.
In this step, specify Local Cell ID.
----End
Example
//Activation procedure
STR DLSIM: LOCELL=1, LR=80;
//Verification procedure
DSP DLSIM: LOCELL=1;
//Deactivation procedure
STP DLSIM: LOCELL=1;
This section describes how to activate, verify, and deactivate the basic feature WRFD-031400
Power Off the Equipment Level by Level.
Prerequisites
l Dependencies on Hardware
Cabinets providing AC input power such as APM30, APM100, and APM200. These
cabinets can be used for outdoor NodeBs.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
Context
After the mains supply is cut off, the NodeB powers off devices by level when certain DC voltage
thresholds are reached. Intelligent shutdown of RF units and NodeBs can prolong the working
time of the system by making efficient use of the available storage batteries.
Procedure
l NodeB V200R014
Activation Procedure
1. Run the NodeB MML command MOD PMU (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Device Panel > Right click PMU board
> PMU Porperty > Power Monitoring Unit; CME batch modification center: not
supported). In this step, set Load Shutdown Flag to ENABLE(Enable) and set Load
Shutdown Voltage(0.1V) if needed.
2. Run the NodeB MML command MOD BATTERY (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Device Panel > Right click PMU
board > Battery Property > Battery; CME batch modification center: not
supported). In this step, set Low Voltage Shutdown Flag to ENABLE and set
Shutdown Voltage(0.1V) if needed.
Verification Procedure
1. Run the NodeB MML command LST PMU and query the values of Load Shutdown
Flag and Load Shutdown Voltage(0.1V).
2. Run the NodeB MML command LST BATTERY and query the values of Low
Voltage Shutdown Flag and Shutdown Voltage(0.1V).
Deactivation Procedure
1. Run the NodeB MML command MOD BATTERY (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Device Panel > Right click PMU
board > Battery Property > Battery; CME batch modification center: not supported)
and set Low Voltage Shutdown Flag to DISABLE(Disable).
2. Run the NodeB MML command MOD PMU (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Device Panel > Right click PMU board
> PMU Porperty > Power Monitoring Unit; CME batch modification center: not
supported) and set Load Shutdown Flag to DISABLE(Disable).
l NodeB V100R014
Activation Procedure
1. Run the NodeB MML command SET SDPA (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Device Panel > PMU Board > PMU
Property > PMU Shutdown Parameter; CME batch modification center: not
supported). In this step, set Load Shutdown Flag to ENABLE(Enable), set Load
Shutdown Voltage(0.1V) if needed, set Low Voltage Shutdown Flag to ENABLE
(Enable), set Shutdown Voltage(0.1V) if needed.
Verification Procedure
1. Run the NodeB MML command LST SDPA, query the values of Load Shutdown
Flag and Load Shutdown Voltage(0.1V),, query the values of Low Voltage
Shutdown Flag and Shutdown Voltage(0.1V),.
Deactivation Procedure
1. Run the NodeB MML command SET SDPA (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Device Panel > PMU Board > PMU
Property > PMU Shutdown Parameter; CME batch modification center: not
supported). In this step, set Load Shutdown Flag to DISABLE(Disable), and set
Low Voltage Shutdown Flag to DISABLE(Disable).
----End
Example
l NodeB V200R014
//Activation procedure
MOD PMU: CN=1, PTYPE=APM30, LSDF=ENABLE, LSDV=430;
MOD BATTERY: CN=1, LVSDF=ENABLE, SDV=360;
//Verification procedure
LST PMU: CN=1;
LST BATTERY: CN=1;
//Deactivation procedure
MOD BATTERY: CN=1, LVSDF=DISABLE;
MOD PMU: CN=1, PTYPE=APM30, LSDF=DISABLE;
l NodeB V100R014
//Activation procedure
SET SDPA: CN=1, LSDF=ENABLE, LSDV=440, LVSDF=ENABLE, SDV=360,
CSLSDF=DISABLE;
//Verification procedure
LST SDPA: CN=1;
//Deactivation procedure
SET SDPA: CN=1, LSDF=DISABLE, LVSDF=DISABLE, CSLSDF=DISABLE;
This section describes how to activate, verify, and deactivate the basic feature WRFD-031500
Solar Power Device Management.
Prerequisites
l Dependencies on Hardware
Only 3900 series base stations support the feature.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
Context
As green energy, solar power is being gradually introduced for supplying power for the NodeB.
This feature enables the NodeB to communicate with a solar controller through the 485 serial
port, therefore managing a solar power device, which makes the NodeB an eco-friendly base
station.
Procedure
l Activation Procedure
1. Run the NodeB MML command ADD PMU (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Device Panel > Add PMU; CME batch
modification center: not supported) to add a PMU. In this step, set Power System
Type to SC48200.
2. Optional: If a diesel generator is required, run the NodeB MML command ADD
DIESELGEN (CME single configuration: NodeB Configuration Express >
IUB_NodeB > Device Panel > Right click PMU board > PMU Property > Diesel
Generator; CME batch modification center: not supported).
Set Intelligent Control Flag to ENABLE(Enable).
Set Rated Power(0.1kVA) based on the rated power specified on the nameplate
of the diesel generator.
l Verification Procedure
1. Run the NodeB MML command DSP PMU to query the configuration information
about the PMU.
Expected result: The value of Power System Type is SC48200.
2. Optional: Run the NodeB MML command LST DIESELGEN to query the
configuration information about the diesel generator.
Expected result: The value of Intelligent Control Flag is ENABLE.
l Deactivation Procedure
1. Run the NodeB MML command RMV DIESELGEN (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Device Panel > Right click PMU
board > PMU Property > Diesel Generator; CME batch modification center: not
supported) to remove a dieselgen.
2. Run the NodeB MML command RMV PMU (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Device Panel > Right click PMU board
> Dlete PMU; CME batch modification center: not supported) to remove a PMU.
----End
Example
//Activation procedure
ADD PMU: CN=0, PTYPE=SC48200, MPN=0, LSDF=ENABLE;
ADD DIESELGEN: CN=0, ICF=ENABLE, POWER=500;
//Verification procedure
DSP PMU: CN=0;
LST DIESELGEN: CN=0;
//Deactivation procedure
RMV DIESELGEN: CN=0;
RMV PMU: CN=0;
This section describes how to activate, verify, and deactivate the basic feature MRFD-210601
Connection with TMA (Tower Mounted Amplifier). (This feature cannot be configured using
the CME. )
Prerequisites
l Dependencies on Hardware
The base station is connected to the Antenna Line Device (ALD) normally.
The BTS3902E cannot support this feature.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
l Others
The TMA is loaded with basic software for its normal operation.
Context
The gain range supported by the Smart Tower-Mounted Amplifier (STMA) varies with models
and vendors.
Procedure
l NodeB V200R014
Activation Procedure
1. Run the NodeB MML command MOD ANTENNAPORT to set ALD Power
Switch to ON.
2. Run the NodeB MML command SCN ALD to scan the Device Name, Vendor
Code and Serial No..
3. Run the NodeB MML command ADD TMA to add a TMA.
4. Optional: If the device supports TMA gain, run the NodeB MML command MOD
TMASUBUNIT to set the TMA gain.
NOTE
It is recommended that you query the gain range supported by the STMA using the NodeB MML
command DSP TMADEVICEDATA before adjusting the gain.
5. Run the NodeB MML command MOD RXBRANCH to modify the RX channel of
an RRU.
Verification Procedure
1. Run the NodeB MML command DSP TMA to query the dynamic information about
a TMA.
Deactivation Procedure
This feature does not need to be deactivated.
l NodeB V100R014
Activation Procedure
1. Run the NodeB MML command SET ALDPWRSW to set Power Supply Switch to
ON(On).
2. Run the NodeB MML command SCN ALD to scan Device Name, Vendor Code and
Serial No..
3. Run the NodeB MML command ADD ALD to add a TMA.
4. Optional: If the device supports TMA gain, run the NodeB MML command SET
TMAGAIN to set the TMA gain.
NOTE
It is recommended that you query the gain range supported by the STMA using the NodeB MML
command DSP TMAFUN before adjusting the gain.
5. Run the NodeB MML command SET RXATTEN to set the attenuation of the RX
channel.
Verification Procedure
1. Run the NodeB MML command LST TMAGAIN to query the TMA gain.
2. Run the NodeB MML command LST RXATTEN to query the RX attenuation value.
Deactivation Procedure
This feature does not need to be deactivated.
----End
Example
l NodeB V200R014
//Activation procedure
MOD ANTENNAPORT: CN=0, SRN=60, SN=0, PN=R0A, PWRSWITCH=ON;
SCN ALD: CTRLCN=0, CTRLSRN=60, CTRLSN=0;
ADD TMA: DEVICENO=0, DEVICENAME="TMA1", CTRLCN=0, CTRLSRN=60,
CTRLSN=0, SUBUNITNUM=1;
MOD TMASUBUNIT: DEVICENO=0, SUBUNITNO=1, CONNPN=R0A, MODE=NORMAL,
GAIN=48;
MOD RXBRANCH: CN=0, SRN=60, SN=0, RXNO=0, ATTEN=0;
//Verification procedure
DSP TMA: DEVICENO=0;
l NodeB V100R014
//Activation procedure
SET ALDPWRSW: CN=0, SRN=60, CASE=REGULAR, AST=TMA12DB_ONLY_NON_AISG,
PSP=R0A, PWRSW=ON;
SCN ALD: CN=0, SRN=60, ACN=R0A;
ADD ALD: NAME="test", CASE=REGULAR, DEVTP=STMA, CN=0, SRN=60,
ACN=R0A, SUBUNIT=1;
SET TMAGAIN: OPMODE=CSAT, CN=0, SRN=60, ACN=R0A, GAIN=48;
SET RXATTEN: CN=0, SRN=60, SN=0, RXNO=0, ATTEN=0;
//Verification procedure
LST TMAGAIN: OPMODE=CSAT, CN=0, SRN=60, ACN=R0A;
This section describes how to activate, verify, and deactivate the basic feature MRFD-210602
Remote Electrical Tilt. (This feature cannot be configured using the CME. )
Prerequisites
l Dependencies on Hardware
The base station is connected to a remote electrical tilt (RET) antenna properly.
The remote control unit (RCU) is compatible with the RET antenna. The RCU is loaded
with a configuration file designated for the RET antenna.
The RCU is loaded with the basic software.
This feature is supported by the all types of BTSs except for the BTS3600C and
BTS3002E.
The BTS3902E cannot support this feature.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
Context
With this feature activated, users can remotely adjust the tilt of an RET antenna to optimize
network performance.
l Calibrating the RET antenna may affect its coverage for a short period of time.
l Calibrating an RET antenna takes up to 4 minutes.
Procedure
l NodeB V200R014
Activation Procedure
1. Optional: If the antenna port is used, run the NodeB MML command MOD
ANTENNAPORT. In this step, set ALD Power Switch to ON.
2. Optional: If the RET antenna port is used, run the NodeB MML command MOD
RETPORT. In this step, set ALD Power Switch to ON.
3. Run the NodeB MML command SCN ALD to obtain the ESN of an ALD.
4. Run the NodeB MML command ADD RET to add an RET antenna.
NOTE
For vendor information, see the antenna equipment manual or scan the RET antenna.
5. Run the NodeB MML command CLB RET to calibrate the RET antenna.
6. Optional: Run the NodeB MML command MOD RETSUBUNIT to modify
parameters concerning an RET antenna subunit.
7. Optional: Run the NodeB MML command MOD RETDEVICEDATA to modify
parameters concerning the attributes of an RET device.
8. Run the NodeB MML command MOD RETTILT to modify the tilt of the RET
antenna.
Verification Procedure
1. Optional: If the antenna port is used, run the NodeB MML command DSP
ANTENNAPORT to query the power switch status for the port.
Expected result: ALD Actual Power Switch is ON.
2. Optional: If the RET antenna port is used, run the NodeB MML command DSP
RETPORT to query the power switch status for the port.
Expected result:ALD Actual Power Switch is ON.
3. Run the NodeB MML command DSP RET to query information about the RET
antenna.
4. Run the NodeB MML command DSP RETSUBUNIT to query the dynamic
information on an RET antenna subunit and an RET antenna's tilt.
Deactivation Procedure
Activation Procedure
1. Run the NodeB MML command SET ALDPWRSW. In this step, set Power Supply
Switch to ON.
2. Run the NodeB MML command SCN ALD to obtain the ESN of an ALD.
3. Run the NodeB MML command ADD ALD to add an antenna device.
NOTE
For vendor information, see the antenna equipment manual or scan the RET antenna.
4. Run the NodeB MML command CLB ANT to calibrate the antenna device.
5. Run the NodeB MML command SET ANTTILT to set the tilt of antenna device.
Verification Procedure
1. Run the NodeB MML command DSP ANTCON to query the power switch status for
the antenna port.
Expected result: Power Supply Switch Run Status is ON.
2. Run the NodeB MML command DSP ANTTILT to query the tilt of the RET antenna.
Expected result: Current Tilt (0.1 degree) is set to the specified value.
Deactivation Procedure
This feature does not need to be deactivated.
----End
Example
l NodeB V200R014
//Activation procedure
MOD ANTENNAPORT: CN=0, SRN=60, SN=0, PN=R0A, PWRSWITCH=ON;
SCN ALD:;
ADD RET: DEVICENO=0, DEVICENAME="RET1", CTRLCN=0, CTRLSRN=60,
CTRLSN=0, RETTYPE=SINGLE_RET, POLARTYPE=SINGLE, SCENARIO=REGULAR;
CLB RET: OPMODE=SUBUNIT, DEVICENO=0, SUBUNITNO=1;
MOD RETSUBUNIT: DEVICENO=0, SUBUNITNO=1;
MOD RETDEVICEDATA: DEVICENO=0, SUBUNITNO=1;
MOD RETTILT: RETCLASS=RET, OPMODE=DEVICENO, DEVICENO=0, TILT=45;
//Verification procedure
DSP ANTENNAPORT:;
DSP RET: DEVICENO=0;
DSP RETSUBUNIT: DEVICENO=0, SUBUNITNO=1;
l NodeB V100R014
//Activation procedure
SET ALDPWRSW: CN=0, SRN=60, CASE=REGULAR, AST=RET_ONLY_COAXIAL,
PSP=R0A, PWRSW=ON;
SCN ALD:;
ADD ALD: NAME="test", CASE=REGULAR, DEVTP=SINGLE_RET, CN=0, SRN=60,
ACN=R0A;
CLB ANT: OPMODE=CSAT, CN=0, SRN=60, ACN=R0A, DEVTP=SINGLE_RET;
SET ANTTILT: OPMODE=CSAT, CN=0, SRN=60, ACN=R0A, DEVTP=SINGLE_RET,
TILT=20;
//Verification procedure
DSP ANTCON:;
DSP ANTTILT: OPMODE=CSAT, CN=0, SRN=60, ACN=R0A;
This section describes how to activate, verify, and deactivate the basic feature WRFD-060003
Configuring Same Band Antenna Sharing Unit (900 MHz). (This feature cannot be configured
using the CME. )
Prerequisites
l Dependencies on Hardware
BTS3902E does not support this feature.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
Context
l The introduction of the feature enables UMTS900 and GSM900 to share the same antenna.
l This feature helps to share an antenna in the same band and decreases the uplink division
loss. After SASU900 is applied, there is no uplink division loss, and the gain is expected
to be between 0 dB and 12 dB.
Procedure
l NodeB V200R014
Activation Procedure
1. Run the NodeB MML command MOD ANTENNAPORT to set ALD Power
Switch to ON.
2. Run the NodeB MML command SCN ALD to scan antenna devices and obtain the
serial number of the SASU.
3. Run the NodeB MML command ADD SASU to configure the SASU and set the
antenna DC power switch state of the SASU.
4. Run the NodeB MML command MOD SASUSUBUNIT to set the SASU working
mode and the gain of the SASU.
Verification Procedure
1. Run the NodeB MML command DSP SASU to query the antenna DC power switch
state of the SASU.
2. Run the NodeB MML command DSP SASUSUBUNIT to query the SASU working
mode and the gain of the SASU.
l NodeB V100R014
Activation Procedure
1. Run the NodeB MML command SET ALDPWRSW to turn on the power supply
switch of the SASU (Same band Antenna Sharing Unit) port.
2. Run the NodeB MML command SCN ALD to scan antenna devices and obtain the
serial number of the SASU.
3. Run the NodeB MML command ADD ALD to configure the SASU.
4. Run the NodeB MML command SET SASUMODE to set the SASU working mode.
5. Run the NodeB MML command SET SASUGAIN to set the gain of the SASU.
6. Run the NodeB MML command SET SASUDCSW to set the antenna DC power
switch state of the SASU.
7. Run the NodeB MML command SET SASUDCLD to set the DC load of the SASU.
Verification Procedure
1. Run the NodeB MML command LST ALD to query the configuration information
about the SASU.
2. Run the NodeB MML command LST SASUMODE to query the SASU working
mode.
3. Run the NodeB MML command LST SASUGAIN to query the gain of the SASU.
4. Run the NodeB MML command LST SASUDCSW to query the antenna DC power
switch state of the SASU.
5. Run the NodeB MML command LST SASUDCLD to query the DC load of the SASU.
Deactivation Procedure
This feature need not be deactivated.
----End
Example
l NodeB V200R014
//Activation procedure
MOD ANTENNAPORT: CN=0, SRN=60, SN=0, PN=R0A, PWRSWITCH=ON,
THRESHOLDTYPE=UER_SELF_DEFINE, UOTHD=1000, UCTHD=1050, OOTHD=1200,
OCTHD=1150;
SCN ALD: CTRLCN=0, CTRLSRN=60, CTRLSN=0;
ADD SASU: DEVICENO=0, DEVICENAME="0_0N0A0SASU_3G", CTRLCN=0,
CTRLSRN=60, CTRLSN=0, DCSWITCH=UMTS;
MOD SASUSUBUNIT: DEVICENO=0, SUBUNITNO=1, MODE=NORMAL, BSGAIN=12,
UMTSGAIN=12, DCLOAD=20;
//Verification procedure
DSP SASU: DEVICENO=0;
DSP SASUSUBUNIT: DEVICENO=0;
l NodeB V100R014
//Activation procedure
SET ALDPWRSW: CN=0, SRN=60, CASE=REGULAR, AST=CUSTOM, PSP=R0A,
PWRSW=ON, UOTHD=1000, UCTHD=1050, OOTHD=1200, OCTHD=1150;
SCN ALD: CN=0, SRN=60, ACN=R0A;
ADD ALD: NAME="0_0N0A0SASU_3G", CASE=REGULAR, DEVTP=SASU, CN=0,
SRN=60, ACN=R0A;
SET SASUMODE: OPMODE=NAME, NAME="0_0N0A0SASU_3G", MODE=BYPASS;
SET SASUGAIN: OPMODE=NAME, NAME="0_0N0A0SASU_3G", CHTP=UMTS, GAIN=12;
SET SASUDCSW: OPMODE=NAME, NAME="0_0N0A0SASU_3G", DCSWITCH=UMTS;
SET SASUDCLD: OPMODE=NAME, NAME="0_0N0A0SASU_3G", DCLOAD=20;
//Verification procedure
LST ALD:;
LST SASUMODE: OPMODE=NAME, NAME="0_0N0A0SASU_3G";
LST SASUGAIN: OPMODE=NAME, NAME="0_0N0A0SASU_3G";
LST SASUDCSW: OPMODE=NAME, NAME="0_0N0A0SASU_3G";
LST SASUDCLD: OPMODE=NAME, NAME="0_0N0A0SASU_3G";
This section describes how to activate, verify, and deactivate the optional feature WRFD-010617
VoIP over HSPA/HSPA+.
Prerequisites
l Dependencies on Hardware
This feature depends on the UE capability and the IP multimedia subsystem (IMS).
l Dependencies on Other Features
In the case of VoIP over HSPA, the following features have been configured before this
feature is activated: WRFD-010610 HSDPA Introduction Package, WRFD-010612
HSUPA Introduction Package, WRFD-010636 SRB over HSUPA and WRFD-010652
SRB over HSDPA.
In the case of VoIP over HSPA+, the WRFD-010686 CPC-DTX/DRX feature has been
configured before this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The UE should support VoIP.
CN should support IP multimedia subsystem (IMS).
Context
VoIP services can be carried on the DCH or HSPA. When VoIP services are carried on the DCH,
a large quantity of resources are consumed. When VoIP services are carried on the HSPA, the
system capacity significantly increases. When the Robust Header Compression (RoHC)
technique is used, the data transmission efficiency of VoIP services is greatly improved.
NOTE
l Data configurations on the BSC6900 and NodeB are required to activate the VoIP over HSPA/HSPA
+ feature.
l To increase the transmission efficiency of VoIP services, it is recommended that the WRFD-011501
PDCP Header Compression (RoHC) feature be activated.
l In the case of HSUPA, it is recommended that the non-scheduling transmission mode be used. In the
case of HSDPA, it is recommended that the Enhanced Proportional Fair (EPF) algorithm be activated.
The purpose is to reduce the delay of VoIP services.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UFRCCHLTYPEPARA (CME single
configuration: UMTS Radio Global Configuration Express > Basic Resource
Control Parameter Configuration > Channel Type Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches). In this step, set
VOIP channel type to HSPA(UL_EDCH,DL_HSDSCH) and IMS channel type
to HSPA(UL_EDCH,DL_HSDSCH).
2. Optional: Run the BSC6900 MML command SET UCORRMALGOSWITCH
(CME single configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to enable the RoHC algorithm. In this step, select the
CFG_PDCP_RFC3095_HC_SWITCH check box under the parameter Channel
Configuration Strategy Switch.
3. Optional: If VoIP services need to use the WRFD-01061403 HSUPA 2ms TTI
feature, run the BSC6900 MML command SET UCORRMALGOSWITCH (CME
single configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, select the
MAP_HSUPA_TTI_2MS_SWITCH check box under the parameter Service
Mapping Strategy Switch. Go to Step 4.
4. Optional:
a. If the NodeB is configured with the WCDMA Baseband Process Unit REV:b
(WBBPb) and Enhanced Base Band Card (EBBC) boards, it is recommended
that 10 ms HSUPA TTI be set for VoIP services. Run the BSC6900 MML
command SET UFRC (CME single configuration: UMTS Radio Global
Configuration Express > Basic Resource Control Parameter
Configuration > RNC Oriented FRC Algorithm Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches). In this step,
select the EDCH_TTI_10ms check box under the parameter HSUPA TTI type
of VOIP service.
b. If the NodeB is configured with the WCDMA Baseband Process Unit REV:d
(WBBPd) and Enhanced Base Band Card REV:d (EBBCd) boards, either 10 ms
or 2 ms HSUPA TTI can be set for VoIP services.
a. To set 10 ms HSUPA TTI for HSUPA services, run the BSC6900 MML
command SET UFRC (CME single configuration: UMTS Radio Global
Configuration Express > Basic Resource Control Parameter
Configuration > RNC Oriented FRC Algorithm Parameters; CME
batch modification center: 3.15 Modifying RNC Parameters in Batches)
l Deactivation Procedure
NOTE
The services admitted before deactivation of this feature are not affected.
The services admitted after the deactivation will not use this feature.
1. Run the BSC6900 MML command SET UFRCCHLTYPEPARA (CME single
configuration: UMTS Radio Global Configuration Express > Basic Resource
Control Parameter Configuration > Channel Type Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches). In this step,
select the DCH(UL_DCH,DL_DCH) check box under the parameter VOIP channel
type, and select the DCH(UL_DCH,DL_DCH) check box under the parameter IMS
channel type.
----End
Example
//Activating VoIP over HSPA/HSPA+
//Operations on the BSC6900 side
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061703 Optimized Scheduling for VoIP over HSPA.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The following features have been configured before this feature is activated:
WRFD-010611 HSDPA Enhanced Package and WRFD-010612 HSUPA
Introduction Package have been configured before this feature is activated for VoIP
over HSPA.
WRFD-010611 HSDPA Enhanced Package and WRFD-010686 CPC- DTX/DRX
have been configured before this feature is activated for VoIP over HSPA+.
Other Prerequisites
The UE should support VoIP.
CN should support IP multimedia subsystem (IMS).
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
RAN10.0 supports VoIP over HSPA. To ensure the QoS of VoIP carried over HSPA, the non-
scheduling method is used for the HSUPA scheduling, and the delay-sensitive (DS) scheduling
algorithm is used for optimized HSDPA scheduling.
Procedure
l Activation Procedure
1. Run the NodeB MML command SET MACHSPARA (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Radio Layer > Locell Algorithm
Parameters > MAC Parameters > MACHSPARA; CME batch modification center:
3.17 Modifying Physical NodeB Parameters in Batches). In this step, set
Scheduling Method to EPF(Enhanced PF).
l Verification Procedure
1. Run the NodeB MML command LST MACHSPARA to query the configuration
result.
l Deactivation Procedure
1. Run the NodeB MML command SET MACHSPARA (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Radio Layer > Locell Algorithm
Parameters > MAC Parameters > MACHSPARA; CME batch modification center:
3.17 Modifying Physical NodeB Parameters in Batches). In this step, set
Scheduling Method to MAXCI(Max C/I), RR(Round Robin), or PF(PF).
----End
Example
//Activation procedure
SET MACHSPARA: LOCELL=0, SM=EPF;
//Verification procedure
LST MACHSPARA: LOCELL=0;
//Deactivation procedure
SET MACHSPARA: LOCELL=0, SM=PF;
This section describes how to activate, verify, and deactivate the basic feature WRFD-010618
IMS Signaling over HSPA.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The configurations of the features on which this feature depends are complete. This
feature depends on the feature WRFD-010610 HSDPA Introduction Package and
WRFD-010612 HSUPA Introduction Package.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
CN should support the signaling indication at Iu interface.
Context
IP Multimedia Subsystem (IMS) signaling over HSPA can shorten the setup delay of IMS
services like VoIP to save network resources for the operator.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UFRCCHLTYPEPARA (CME single
configuration: UMTS Radio Global Configuration Express > Basic Resource
Control Parameter Configuration > Channel Type Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches) to set IMS
channel type to HSPA(UL_EDCH,DL_HSDSCH).
l Verification Procedure
1. In the Navigation Tree pane on the BSC6900 LMT, click the Trace tab. In the
displayed Trace Navigation Tree pane, double-click UMTS Services. On the
unfolded list, double-click Uu Interface Trace. In the displayed Uu Interface
l Deactivation Procedure
1. Run the BSC6900 MML command SET UFRCCHLTYPEPARA (CME single
configuration: UMTS Radio Global Configuration Express > Basic Resource
Control Parameter Configuration > Channel Type Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches) to set IMS
channel type to DCH(UL_DCH,DL_DCH).
----End
Example
//Activating IMS Signaling over HSPA.
SET UFRCCHLTYPEPARA: ImsChlType=HSPA;
//Deactivating IMS Signaling over HSPA.
SET UFRCCHLTYPEPARA: ImsChlType=DCH;
This section describes how to activate, verify, and deactivate the optional feature WRFD-011501
PDCP Header Compression (RoHC).
Prerequisites
l Dependencies on Hardware
The UE supports this feature.
l Dependencies on Other Features
WRFD-010619 CS Voice over HSPA/HSPA+
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The UE should support the ROHC compression function.
Context
PDCP header compression (RoHC) mainly applies to VoIP services to reduce IP overhead. This
feature provides an IP header compression mechanism, which aims to save the bandwidth over
the Uu interface, thereby reducing occupancy of radio resources.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, select the
CFG_PDCP_RFC3095_HC_SWITCH check box under the parameter Channel
configuration strategy switch. Select the following parameters in the Compatibility
Switch list box:
CMP_RAB_5_CFG_ROHC_SWITCH
CMP_RAB_6_CFG_ROHC_SWITCH
CMP_RAB_7_CFG_ROHC_SWITCH
CMP_RAB_8_CFG_ROHC_SWITCH
CMP_RAB_9_CFG_ROHC_SWITCH
l Verification Procedure
1. On the BSC6900 LMT, click Trace > UMTS Service, and double-click Uu Interface
Trace to display the Uu Interface Trace window.
2. Set Cell config, Uu Message Type, and Save File, and then click Submit.
3. Enable the UE to establish VoIP services.
4. Check the rb-InformationSetupList message in the traced data:
If this message contains the IE headerCompressionInfoList, as shown in Figure
64-1, this feature has been activated.
If this message does not contain the IE headerCompressionInfoList, this feature
has not been activated.
Figure 64-1
l Deactivation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, deselect the
CFG_PDCP_RFC3095_HC_SWITCH check box under the parameter Channel
configuration strategy switch. Disable the following switches in the Compatibility
Switch list box:
CMP_RAB_5_CFG_ROHC_SWITCH
CMP_RAB_6_CFG_ROHC_SWITCH
CMP_RAB_7_CFG_ROHC_SWITCH
CMP_RAB_8_CFG_ROHC_SWITCH
CMP_RAB_9_CFG_ROHC_SWITCH
----End
Example
//Activating PDCP Header Compression (RoHC)
SET UCORRMALGOSWITCH: CfgSwitch=CFG_PDCP_RFC3095_HC_SWITCH-1,
CmpSwitch=CMP_RAB_5_CFG_ROHC_SWITCH-1&CMP_RAB_6_CFG_ROHC_SWITCH-1&CMP_RAB
_7_CFG_ROHC_SWITCH-1&CMP_RAB_8_CFG_ROHC_SWITCH-1&CMP_RAB_9_CFG_ROHC_SWITC
H-1;
//Deactivating PDCP Header Compression (RoHC)
SET UCORRMALGOSWITCH: CfgSwitch=CFG_PDCP_RFC3095_HC_SWITCH-0,
CmpSwitch=CMP_RAB_5_CFG_ROHC_SWITCH-0&CMP_RAB_6_CFG_ROHC_SWITCH-0&CMP_RAB
_7_CFG_ROHC_SWITCH-0&CMP_RAB_8_CFG_ROHC_SWITCH-0&CMP_RAB_9_CFG_ROHC_SWITC
H-0;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010619
CS Voice over HSPA/HSPA+.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The following features have been configured before this feature is activated:
WRFD-010610 HSDPA Introduction Package, WRFD-010612 HSUPA
Introduction Package, WRFD-010652 SRB over HSDPA, and WRFD-010636 SRB
over HSUPA, in the case of CS voice over HSPA.
WRFD-010686 CPC-DTX/DRX, in the case of CS voice over HSPA+.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The UE is of 3GPP Release 8 or higher and CS voice services are capable of being
carried on HSPA/HSPA+.
Context
The implementation of CS voice services over HSPA is introduced in 3GPP Release 8. In the
case of CS voice services over HSPA, uplink CS voice packets are carried on the E-DCH and
downlink CS voice packets are carried on the HS-DSCH.
CS Voice over HSPA is intended for CS conversational AMR and AMR WB. CS streaming
services are still carried on the DCH. The IMS for VoIP services is not required because the CS
voice services over HSPA are carried on the CS domain of the CN.
NOTE
l Data configurations on the BSC6900 and NodeB are required to activate the CS Voice over HSPA/
HSPA+.
l In the case of HSUPA, it is recommended that the non-scheduling transmission mode be used, which
does not need to be configured. In the case of HSDPA, it is recommended that the Enhanced
Proportional Fair (EPF) algorithm be activated. The purpose is to reduce the delay of CS voice services.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UFRCCHLTYPEPARA (CME single
configuration: UMTS Radio Global Configuration Express > Basic Resource
Control Parameter Configuration > Channel Type Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches) to configure the
uplink EDCH and downlink HSDSCH as the channels carrying HSPA CS services.
In this step, select the HSPA(UL EDCH,DL HSDSCH) check box under the
parameter CS voice channel type.
2. Optional: If CS voice services need to be carried on the 2 ms Transmission Time
Interval (TTI), run the BSC6900 MML command SET
UCORRMALGOSWITCH (CME single configuration: UMTS Radio Global
Configuration Express > Connection_Oriented RRM Switch Configuration >
Connection Oriented Algorithm Switches; CME batch modification center: 3.15
Modifying RNC Parameters in Batches). In this step, select the
MAP_HSUPA_TTI_2MS_SWITCH check box under the parameter Service
Mapping Strategy Switch. Go to Step 3.
3. Optional: Configure the HSUPA TTI type of the VoIP service.
a. If the NodeB is configured with the WCDMA Baseband Process Unit REV:b
(WBBPb) and Enhanced Base Band Card (EBBC) boards, it is recommended
that 10 ms HSUPA TTI be set for VoIP services. Run the BSC6900 MML
command SET UFRC (CME single configuration: UMTS Radio Global
Configuration Express > Basic Resource Control Parameter
Configuration > RNC Oriented FRC Algorithm Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches). In this step,
select the EDCH_TTI_10ms check box under the parameter HSUPA TTI type
of VOIP service.
b. If the NodeB is configured with the WCDMA Baseband Process Unit REV:d
(WBBPd) and Enhanced Base Band Card REV:d (EBBCd) boards, either 10 ms
or 2 ms HSUPA TTI can be set for VoIP services.
a. To set 10 ms HSUPA TTI for HSUPA services, run the BSC6900 MML
command SET UFRC (CME single configuration: UMTS Radio Global
Configuration Express > Basic Resource Control Parameter
Configuration > RNC Oriented FRC Algorithm Parameters; CME
batch modification center: 3.15 Modifying RNC Parameters in Batches)
to select the EDCH_TTI_10ms check box under the parameter HSUPA
TTI type of VOIP service.
b. To set 2 ms HSUPA TTI for HSUPA services, do as follows:
1) Run the BSC6900 MML command SET UFRC (CME single
configuration: UMTS Radio Global Configuration Express > Basic
Resource Control Parameter Configuration > RNC Oriented FRC
Algorithm Parameters; CME batch modification center: 3.15
l Deactivation Procedure
NOTE
The services admitted before deactivation of this feature are not affected.
The services admitted after the deactivation will not use this feature.
1. Run the BSC6900 MML command SET UFRCCHLTYPEPARA (CME single
configuration: UMTS Radio Global Configuration Express > Basic Resource
Control Parameter Configuration > Channel Type Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches). In this step,
select the DCH(UL_DCH,DL_DCH) check box under the parameter CS voice
channel type.
----End
Example
/*Activation procedure*/
//Operations on the BSC6900 side
This section describes how to activate, verify, and deactivate the optional feature WRFD-010613
AMR-WB (Adaptive Multi Rate Wide Band). (This feature cannot be configured using the
CME. )
Prerequisites
l Dependencies on Hardware
The CN supports associated specifications.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The UE supports associated specifications.
The AMR-WB function is enabled on the MSC and UMG.
The UE must have the corresponding support capability.
The CN must have the corresponding support capability.
Context
This feature provides AMR-WB services, which help improve the QoS of voice services when
resources are sufficient.
CAUTION
l If the license of the AMR-WB service is not activated on a RNC, ensure that AMR-WB is
not enabled for this RNC on the CS core network side. Otherwise, both the AMR-NB services
and emergency calls cannot be set up for the UE supporting AMR-WB.
l If the license of the AMR-WB service is enabled on a RNC, ensure that AMR-WB is enabled
for this RNC on the CS core network side. Otherwise, the AMR-WB service cannot be set
up.
l This feature is an integrated solution. To enable this feature, specific parameters must be
configured based on the actual network conditions. Contact Huawei for technical support.
l Do not configure relevant parameters without the assistance of Huawei technical personnel;
otherwise, the network capacity and KPI values may be affected.
Procedure
l Activation Procedure
1. Optional: Run the BSC6900 MML command SET UAMRCWB to set the RNC-
level speech rates for the gold, silver, and bronze users.
2. Optional: Run the BSC6900 MML command ADD UCELLAMRCWB to set cell-
level speech rates for the gold, silver, and bronze users.
l Verification Procedure
1. Optional: Run the BSC6900 MML command LST UAMRCWB to query the AMR-
WB speech rates of the gold, silver, and bronze users.
2. Optional: Run the BSC6900 MML command LST UCELLAMRCWB to query the
AMR-WB speech rates for the gold, silver, and bronze users.
3. On the BSC6900 LMT, open the Monitor tab page, choose Monitor > Monitor >
UMTS Monitoring > Cell Performance Monitoring, and create a task of AMR
Mode.
4. Enable the AMR-WB function on UE1 and UE2, and enable the UEs to camp on the
cell CELL_A11.
5. Use UE1 to initiate a voice call to UE2. The call is successfully established and the
voice is clear.
6. Check the AMR mode on the LMT and verify that the downlink rate of UE1 reaches
the specified value.
l Deactivation Procedure
Run the BSC6900 MML command SET LICENSE to deactivate the license controlling
this feature.
NOTE
After deactivating the license controlling this feature, a WB-AMR cannot establish WB and NB
services. If the WB rate for the RNC is disabled, a WB-AMR UE still can establish NB services.
----End
Example
//Activating AMR-WB
//Setting RNC-level parameters for the WB-AMR speech rate control (WB-
AMRC) algorithm
This section describes how to activate, verify, and deactivate the basic feature WRFD-020701
AMR/WB-AMR Speech Rates Control.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
If this feature is to be applied to Adaptive Multi Rate Wide Band (AMR WB), this
feature depends on WRFD-010613 AMR-WB.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The UE supports TFC control processing.
Context
This feature enables the adjustment of AMR/AMR-WB speech rates triggered by multiple
factors. This ensures uninterrupted services, expands the service coverage area, and reduces the
cell load.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, set CS Algorithm Switch to
CS_AMRC_SWITCH.
2. Run the BSC6900 MML command SET UQOSACT (CME single configuration:
UMTS Radio Global Configuration Express > QOS Parameter Configuration >
1. On the BSC6900 LMT, open the Monitor tab page. In the Monitor tab page, double-
click UMTS Monitoring > Connection Performance Monitoring. In the displayed
dialog box, set Monitor Item to AMR Mode and specify IMSI.
2. On the BSC6900 LMT, open the Trace tab page. In the Trace tab page, double-click
UMTS Services > Uu Interface Trace. In the displayed dialog box, specify the RNC
ID and the Cell ID, as shown in Figure 67-1.
3. Two test UEs supporting AMR WB are available and camp on the cell named
CELL_A11. Use UE A to call UE B. The call is established.
4. Check whether the following information elements (IEs) are contained in the traced
RRC_MEAS_CTR message, as shown in Figure 67-2.
event6a
event6b
5. Place UE B in the center of the cell, and move UE A towards or away from UE B.
Check whether the AMR mode changes during performance monitoring, as shown in
Figure 67-3.
l Deactivation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Example
//Activating AMR/WB-AMR Speech Rates Control
SET UCORRMALGOSWITCH: CsSwitch=CS_AMRC_SWITCH-1;
SET UQOSACT: AMRQosPerform=YES, UlQosAmrAdjSwitch=YES,
UlQosWAmrAdjSwitch=YES, DlQosAmrAdjSwitch=YES, DlQosWAmrAdjSwitch=YES;
MOD UTYPRABQUALITYMEAS: RabIndex=1, UlThd6a1=1, UlThd6a2=5, UlThd6b1=1,
UlThd6b2=5, StaBlkNum5A=500, Thd5a=280, HangBlockNum5a=512, ThdEa=2,
ThdEb=2;
//Setting the AMR speech rate control parameters
SET UCORRMPARA: ReservedSwitch0=RESERVED_SWITCH_0_BIT4-0;
SET UAMRC: GoldMaxMode=NBAMR_BITRATE_6.70K,
SilverMaxMode=NBAMR_BITRATE_6.70K, CopperMaxMode=NBAMR_BITRATE_6.70K;
//Setting the AMR-WB speech rate control parameters
SET UCORRMPARA: ReservedSwitch0=RESERVED_SWITCH_0_BIT3-0;
SET UAMRCWB: GoldMaxMode=WBAMR_BITRATE_12.65K,
SilverMaxMode=WBAMR_BITRATE_12.65K, CopperMaxMode=WBAMR_BITRATE_12.65K;
68 Configuring TFO/TrFO
This section describes how to activate, verify, and deactivate the optional feature WRFD-011600
TFO/TrFO.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The CN node supports this feature.
The UE supports this feature.
Context
This feature helps implement the functions of TFO/TrFO by identifying the Iu user plane (IuUP)
V2 core network (CN) and processing related services.
This feature can prevent speech quality deterioration caused by the interpretation between
different coder and decoders (CODECs). The TrFO can also save the transmission resources.
If the TFO function is enabled on the GSM side, the AMRC rate adjustment function must
enabled together with this feature on the UMTS side to enable communications between GSM
and UMTS users to support the TFO function. To fully utilize this function, it is good practice
to enable the AMRC rate adjustment function on both UMTS users in a conversation.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Example
//Activation procedure
SET UCORRMALGOSWITCH: CsSwitch=CS_IUUP_V2_SUPPORT_SWITCH-1;
//Deactivation procedure
SET UCORRMALGOSWITCH: CsSwitch=CS_IUUP_V2_SUPPORT_SWITCH-0;
This section describes how to activate, verify, and deactivate the optional feature WRFD-140201
AMR Voice Quality Improvement Based on PLVA.
Prerequisites
l Dependencies on Hardware
This feature has the following impact on the NodeB hardware:
The BTS3812E, BTS3812A and BTS3812AE must be configured with the EULPd
board.
The DBS3800 must be configured with the EBBCd board.
The 3900 series base station must be configured with the WBBPd or WBBPf board.
Currently, for baseband boards, only the EULPd, EBBCd, WBBPd and WBBPf
boards support the PLVA feature. When the EULPd, EBBCd, WBBPd or WBBPf
board is inserted together with the other types of baseband boards, AMR services
cannot obtain the PLVA gain if the AMR services are set up on the other types of
baseband boards.
l Dependencies on Other Features
None
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Procedure
l Activation Procedure
After the license is activated, this feature has been activated.
l Verification Procedure
The VS.PLVA.User counter informs operators of the number of UEs using this feature.
Verify that the value of the counter VS.PLVA.User is not 0. A non-zero value indicates
that this feature takes effect.
l Deactivation Procedure
None
----End
Example
None
This section describes how to activate, verify, and deactivate the optional feature WRFD-011000
Cell Broadcast Service.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others
The UE is capable of receiving cell broadcast messages.
Context
This feature supports the standard cell broadcast procedure specified in the related protocol and
therefore helps the cell broadcast center (CBC) implement cell broadcast services.
Procedure
l Activation Procedure
External CBCs are deployed in an ATM or IP network. The ATM network is used as an
example in this document.
1. Run the BSC6900 MML command RMV URNCCBCPUID (CME single
configuration: IUBC Configuration Express > ATM Transport > RNC Broadcast
Message Main CPUID; CME batch modification center: not supported) to disable
the configuration of the built-in CBC.
2. Run the BSC6900 MML command SET URNCCBPARA (CME single
configuration: UMTS Radio Global Configuration Express > Iu-BC Interface
Configuration > RNC Cell Broadcast Message Para; CME batch modification
center: 3.15 Modifying RNC Parameters in Batches) to turn off CB Switch.
3. Run the BSC6900 MML command ADD DEVIP (CME single configuration: IUBC
Configuration Express > ATM Transport > Device IP Address; CME batch
modification center: not supported) to add the device IP address of the interface board.
4. Run the BSC6900 MML command ADD IPOAPVC (CME single configuration:
IUBC Configuration Express > ATM Transport > IPoA PVC; CME batch
modification center: not supported) to add an Internet Protocol over ATM (IPoA)
permanent virtual circuit (PVC).
NOTE
e. Run the BSC6900 MML command DSP UCELL to check whether the CBS
function works, as shown in Figure 70-3.
d. It can be viewed from the Uu interface trace data that the RNC stops sending the
UU_BMC_MSG_TYPE message beginning with 01.
l Deactivation Procedure
1. Run the BSC6900 MML command RMV UCBSADDR (CME single configuration:
IUBC Configuration Express > ATM Transport > CBS Address; CME batch
modification center: not supported) to disable Cell Broadcast Service.
----End
Example
//Activating Cell Broadcast Service
This section describes how to activate, verify, and deactivate the optional feature WRFD-011001
Simplified Cell Broadcast.
Prerequisites
l Dependencies on Hardware
OnlyBSC6900 supports this feature.
l Dependencies on Other Features
This feature and the feature WRFD-011000 Cell Broadcast Service cannot be used
together.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others
The UE is capable of receiving cell broadcast messages.
Context
This feature is used to send simple cell broadcast messages by running a BSC6900 MML
command on the M2000 or BSC6900 LMT when the cell broadcast center (CBC) is not
configured.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command RMV UCBSADDR (CME single configuration:
IUBC Configuration Express > IP Transport > CBS Address; CME batch
modification center: not supported) to remove the IP address of the external CBC.
2. Run the BSC6900 MML command ADD URNCCBCPUID (CME single
configuration: IUBC Configuration Express > IP Transport > RNC Broadcast
Message Main CPUID; CME batch modification center: not supported) to configure
the SPU subsystem of the built-in CBC.
3. Run the BSC6900 MML command SET URNCCBPARA (CME single
configuration: UMTS Radio Global Configuration Express > Iu-BC Interface
Configuration > RNC Cell Broadcast Message Para; CME batch modification
center: 3.15 Modifying RNC Parameters in Batches). In this step, set CB Switch
to ON(ON) to enable the built-in CBC for the RNC.
4. Run the BSC6900 MML command ADD UCTCH (CME single configuration:
UMTS Cell Configuration Express > Channel Configuration > CTCH; CME
batch modification center: not supported) to add the common traffic channel (CTCH)
to a cell.
5. Run the BSC6900 MML command ADD UCELLCBSDRX (CME single
configuration: UMTS Cell Configuration Express > Cell Broadcast Service > Cell
CBS DRX Parameters; CME batch modification center: 3.18 Modifying UMTS
Cell Parameters in Batches) to add the CBS discontinuous reception (DRX)
scheduling parameter.
6. Run the BSC6900 MML command ADD UCELLCBSSAC (CME single
configuration: UMTS Cell Configuration Express > Cell Broadcast Service > Cell
CBS SAC; CME batch modification center: 3.18 Modifying UMTS Cell Parameters
in Batches) to add a CBS area and a broadcast message.
7. Run the BSC6900 MML command ACT UCELLCBS (CME single configuration:
UMTS Cell Configuration Express > Cell Broadcast Service > Cell CBS. Set Cell
CBS state to Activated; CME batch modification center: not supported) to enable the
CBS function for a cell.
l Verification Procedure
1. Check whether the CBS function works properly.
l Deactivation Procedure
1. Run the BSC6900 MML command DEA UCELLCBS (CME single configuration:
UMTS Cell Configuration Express > Cell Broadcast Service > Cell CBS. Set Cell
CBS state to Deactivated; CME batch modification center: not supported) to disable
the CBS function for a cell.
2. Run the BSC6900 MML command SET URNCCBPARA (CME single
configuration: UMTS Radio Global Configuration Express > Iu-BC Interface
Configuration > RNC Cell Broadcast Message Para; CME batch modification
center: 3.15 Modifying RNC Parameters in Batches). In this step, set CB Switch
to OFF(OFF) to turn off the CBS switch for the BSC6900.
----End
Example
//Activating Simplified Cell Broadcast
This section describes how to activate, verify, and deactivate the optional feature WRFD-020127
Warning of Disaster.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The configurations of the features on which this feature depends are complete. This
feature depends on the feature WRFD-011001 Simplified Cell Broadcast.
l License
This feature is not under license control.
Context
With this feature, the Cell Broadcast Center (CBC) incorporated into the RNC informs all users
in specified cells of the disaster information through message broadcasting in the shortest time,
therefore minimizing the impact of the disaster.
NOTE
Procedure
l Activation Procedure
1. For detailed operations for activating license, see Activating the BSC6900 License.
2. (Optional) Run the BSC6900 MML command RMV UCBSADDR (CME single
configuration: IUBC Configuration Express > IP Transport > CBS Address; CME
batch modification center: not supported) to remove the CBS configuration, if the
operator configured the CBS function using external CBC.
3. Run the BSC6900 MML command SET URNCCBPARA (CME single
configuration: UMTS Radio Global Configuration Express > Iu-BC Interface
Configuration > RNC Cell Broadcast Message Para; CME batch modification
center: 3.15 Modifying RNC Parameters in Batches) to set CB switch and CTCH
switch of cell broadcast to ON. By doing this, the system can configure the disaster
warning message and send the message to UEs.
4. Run the BSC6900 MML command ADD URNCCBCPUID (CME single
configuration: IUBC Configuration Express > IP Transport > RNC Broadcast
Message Main CPUID; CME batch modification center: not supported) to configure
the SPU subsystem for the built-in CBC.
5. Run the BSC6900 MML command ADD UCBSAREA (CME single configuration:
UMTS Global Configuration Express > Radio Basic Data Configuration >
Simple Cell Broadcast Area; CME batch modification center: not supported) to
configure the broadcast area. The broadcast area can be a LAC, a cell, or all cells under
the RNC.
6. Run the BSC6900 MML command ADD UCBSMSG (CME single configuration:
UMTS Global Configuration Express > Radio Basic Data Configuration >
Simplified CBS Message; CME batch modification center: not supported) or MOD
UCBSMSG (CME single configuration: UMTS Global Configuration Express >
Radio Basic Data Configuration > Simplified CBS Message; CME batch
modification center: not supported) to configure the broadcast message.
NOTE
l When disasters (such as earthquakes, tsunamis, and hurricanes) occur, Set Geography
Scope to CellImmediate, and set CBS Message Priority to High so that users can receive
the message in time.
l It is recommended to set Number of CBS Messages to a value greater than 3 to ensure
that all UEs can receive the message.
l Verification Procedure
1. Use a test UE to camp on the cell, and then activate the feature. Check whether the
test UE can receive the disaster warning message.
NOTE
A UE can receive this message only after it is enabled with the 3G broadcast message receiving
function.
l Deactivation Procedure
1. Run the BSC6900 MML command SET URNCCBPARA (CME single
configuration: UMTS Radio Global Configuration Express > Iu-BC Interface
Configuration > RNC Cell Broadcast Message Para; CME batch modification
center: 3.15 Modifying RNC Parameters in Batches) to set CTCH switch of cell
broadcast to OFF.
----End
Example
//Activating warning of disaster (The following procedure uses a cell as
an example.)
RMV UCBSADDR: CnOpIndex=0;
SET URNCCBPARA: CBSwitch=ON, CTCHSwitch =ON;
ADD URNCCBCPUID: CnOpIndex=1, SRN=0, SN=2, SSN=1;
ADD UCBSAREA: AreaId=1, CnOpIndex=1, AreaType=CELL, CellId=22;
ADD UCBSMSG: MsgIndex=0, MsgTypeId=1, GeographicalScope=CellImmediate,
Priority=High, RepetPeriod=10, NumOfBrdcstReq=5, CodeType=English,
AreaID=1, EmergencyType=Other, CBSMsg="Hurricane";
//Deactivating warning of disaster
SET URNCCBPARA: CTCHSwitch=OFF;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010616
MBMS Introduction Package.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others
The existing PS domain functional entities (GGSN, SGSN, UTRAN, and UE) support
the Multimedia Broadcast Multicast Service (MBMS) bearer service.
A new functional entity, that is, the broadcast multicast service centre (BM-SC) is added
to provide a set of functions for the MBMS services.
The UE supports MBMS functions.
Context
The MBMS feature is an important feature specified by 3GPP Release 6. When MBMS is
enabled, point-to-multipoint multimedia services can be forwarded from one entity to multiple
entities over a common channel. In this way, the resources can be shared.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UMBMSSWITCH (CME single
configuration: UMTS Radio Global Configuration Express > MBMS
Configuration > MBMS Switch; CME batch modification center: 3.15 Modifying
RNC Parameters in Batches) to set MBMS Control Switch to ON(ON).
2. Run the BSC6900 MML command ADD UMBMSSA (CME single configuration:
UMTS Radio Global Configuration Express > MBMS Configuration > MBMS
SA; CME batch modification center: not supported) to add the MBMS service area
according to the network plan.
3. Run the BSC6900 MML command ADD UCELLMBMSSA (CME single
configuration: UMTS Cell Configuration Express > MBMS Configuration >
Relation Between Cell and SA; CME batch modification center: not supported) to
add the mapping between the cell and the MBMS service area (SA) according to the
network plan.
4. Run the BSC6900 MML command ADD USCCPCHBASIC (CME single
configuration: UMTS Cell Configuration Express > Channel Configuration >
SCCPCH Basic Information; CME batch modification center: not supported) to add
the SCCPCH according to the network plan.
5. Run the BSC6900 MML command ADD UFACH (CME single configuration:
UMTS Cell Configuration Express > Channel Configuration > FACH; CME
batch modification center: not supported) to add the FACH according to the network
plan.
6. Run the BSC6900 MML command ADD UFACHDYNTFS (CME single
configuration: UMTS Cell Configuration Express > Channel Configuration >
Dynamic TFS of FACH; CME batch modification center: not supported) to add the
transport format set (TFS) of an FACH according to the network plan.
7. Run the BSC6900 MML command ADD UFACH (CME single configuration:
UMTS Cell Configuration Express > Channel Configuration > FACH; CME
batch modification center: not supported) to add a logical channel mapped to an FACH
according to the network plan.
8. Run the BSC6900 MML command ADD USCCPCHTFC (CME single
configuration: UMTS Cell Configuration Express > Channel Configuration >
TFC of SCCPCH; CME batch modification center: not supported) to add the
Calculated Transport Format Combination (CTFC) of an SCCPCH according to the
network plan.
9. Run the BSC6900 MML command ADD UCELLMCCH (CME single
configuration: UMTS Cell Configuration Express > Channel Configuration >
Configuration of the MCCH And MICH; CME batch modification center: not
supported) to add the MCCH and the MICH for the cell according to the network plan.
10. Configure the cell-level MBMS parameters according to the network plan.
a. Run the BSC6900 MML command ACT USCCPCH (CME single
configuration: UMTS Cell Configuration Express > Channel Configuration
> SCCPCH Basic Information. Set Validation indication to Activated; CME
batch modification center: not supported) to activate the configuration
information of an SCCPCH.
b. Run the BSC6900 MML command ACT UCELLMBMS (CME single
configuration: UMTS Cell Configuration Express > MBMS Configuration >
Cell MBMS Status. Set Cell MBMS state to Activated; CME batch
modification center: not supported) to activate the MBMS configuration data for
the cell.
11. Run the BSC6900 MML command SET UMTCH (CME single configuration:
UMTS Radio Global Configuration Express > MBMS Configuration > Semi-
Example
//Activation MBMS Introduction Package
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061602 MBMS Admission Control.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
The feature WRFD-010616 MBMS Introduction Package must be configured before
this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
The admission criteria of Iub resources and credit resources for the Multimedia Broadcast and
Multicast Service point-to-point/point-to-multipoint resource block (MBMS PtP/PtM RB)
requests is the same as that for other services. The cell power resources are preferentially
allocated to high-priority MBMS broadcasting services. Only the activation procedure of the
resource admission on the Uu interface is provided in this section.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command MOD UCELLALGOSWITCH (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Algorithm Switches; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches). In this step, select MBMS_UU_ADCTRL(MBMS UU
Load Admission Control Algorithm) from the Cell CAC algorithm switch drop-
down list to enable the MBMS admission control on the Uu interface and select a
proper admission algorithm according to the network plan.
l Verification Procedure
1. Enable the MBMS admission algorithm, and then limit cell resources to ensure that
the admission resources are insufficient. In this manner, the admission fails. An
example is given as follows:
a. Run the BSC6900 MML command ADD URESERVEOVSF to reserve the
downlink Orthogonal Variable Spreading Factor (OVSF) for the cell so that only
64 kbit/s services are supported in the cell.
b. Originate a 256 kbit/s service. Check the messages traced on the Iu interface on
the RNC side, which are the MBMS SESSION START message from the core
network (CN) to the RNC and the MBMS SESSION START RSPPONSE
message from the RNC to the CN.
c. Run the BSC6900 MML command DSP UCELLMBMSSERVICE. If the
parameter Reason of service setup failure is Access Failure, the MBMS
admission algorithm takes effect.
2. Disable the MBMS admission algorithm, and the services are successfully admitted.
l Deactivation Procedure
1. Run the BSC6900 MML command MOD UCELLALGOSWITCH (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Algorithm Switches; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches). In this step, deselect MBMS_UU_ADCTRL(MBMS UU
Load Admission Control Algorithm) from the Cell CAC algorithm switch drop-
down list to disable the MBMS admission algorithm.
----End
Example
//Activating MBMS Admission Control
MOD UCELLALGOSWITCH: CellId=1, NBMCacAlgoSwitch=MBMS_UU_ADCTRL-1,
NBMDlCacAlgoSelSwitch=ALGORITHM_FIRST;
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061603 MBMS Load Control.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
The feature WRFD-010616 MBMS Introduction Package must be configured before
this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
The feature helps to lighten the cell load when the cell enters the congestion state and ensures
the system stability. When the cell is in the basic congestion state and downlink congestion is
detected, the power consumed by MBMS services is reduced.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command MOD UCELLALGOSWITCH (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Algorithm Switches; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches). In this step, select DL_UU_LDR(Downlink UU LDR
Algorithm) and DL_UU_OLC(Downlink UU OLC Algorithm) from the Cell LDC
algorithm switch drop-down list to enable downlink load reshuffling and downlink
overload congestion control on the Uu interface.
2. Run the BSC6900 MML command MOD UCELLLDR (CME single configuration:
UMTS Cell Configuration Express > Cell Parameters > Cell LDR Algorithm
Parameters; CME batch modification center: 3.18 Modifying UMTS Cell
----End
Example
//Activating MBMS Load Control
//Enabling downlink load reshuffling and downlink overload congestion
control on the Uu interface
MOD UCELLALGOSWITCH: CellId=1, NBMLdcAlgoSwitch= DL_UU_LDR-1&DL_UU_OLC-1;
//Setting the first LDR-triggered action to power reduction of MBMS
services
MOD UCELLLDR: CellId=1, DlLdrFirstAction=MBMSDECPOWER;
//Enabling the triggered OLC to release MBMS services on a one-by-one
basis
ADD UCELLOLC: CellId=1, SeqOfUserRel=MBMS_REL, MbmsOlcRelNum=1;
//Verifying MBMS Load Control
MOD UCELLLDM: CellId=1, DlLdrTrigThd=2, DlLdrRelThd=1, DlOlcTrigThd=2,
DlOlcRelThd=1;
//Deactivating MBMS Load Control
MOD UCELLALGOSWITCH: CellId=1, NBMLdcAlgoSwitch= DL_UU_LDR-0&DL_UU_OLC-0;
MOD UCELLLDR: CellId=1, DlLdrFirstAction=NoAct;
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061605 MBMS Transport Resource Management.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
The features WRFD-010616 MBMS Introduction Package must be configured before
this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
For the same MBMS session in the same Node B, a separate Iub transport bearer is established
for each cell. An example is shown in the following figure assuming 3 cells in one Node B.
Three copies of exact same MBMS session data are sent through the Iub from the CRNC to the
Node B.
Procedure
l Activation Procedure
The feature does not need to be activated.
l Verification Procedure
1. Use UEs to require an MBMS service in the two cells under the same NodeB.
2. Check the signaling traced on the Iub interface.
You may find two pairs of COMMON TRANSPORT CHANNEL SETUP
REQUEST/COMMON TRANSPORT CHANNEL SETUP RESPONSE
messages.
The BROADCAST REFERENCE IEs in the two COMMON TRANSPORT
CHANNEL SETUP REQUEST messages are different. This indicates that the
messages are from different Iub interfaces.
Both the COMMON TRANSPORT CHANNEL SETUP RESPONSE
messages contain the TLA and Binding ID.
l Deactivation Procedure
This feature does not need to be deactivated.
----End
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061606 Streaming Service on MBMS.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The configurations of the features on which this feature depends are complete. This
feature depends on the feature WRFD-010616 MBMS Introduction Package.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature enables the MBMS service to be carried on the PS streaming class, therefore
ensuring QoS.
Procedure
l Activation Procedure
This feature can be activated only after MBMS basic functions are enabled. For details, see
the section "Configuring MBMS Introduction Package".
The parameters of streaming services have been configured by the RNC by default. This
feature is used as long as the CN sends MBMS services in the form of PS streaming. No
activation operation is needed.
l Verification Procedure
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061608 16/32/64/128Kbps Channel Rate on MBMS.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
The features WRFD-010616 MBMS Introduction Package must be configured before
this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature is related to four MBMS channel rates: 16 kbit/s, 32 kbit/s, 64 kbit/s, and 128 kbit/
s.
Procedure
l Activation Procedure
This section describes how to activate, verify, and deactivate the optional feature WRFD-010660
MBMS Phase 2.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
The features WRFD-010616 MBMS Introduction Package must be configured before
this feature is activated.
l License
This feature is not under license control.
l Other Prerequisites
UE should support the corresponding enhanced MBMS functions.
Context
This feature supports the enhanced MBMS (PTP/PTM) to save cell resources. The MBMS phase
2 includes following features:
Procedure
l Activation Procedure
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01066001 MBMS Enhanced Broadcast Mode.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
The features WRFD-010616 MBMS Introduction Package must be configured before
this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
Compared with broadcast mode, it is a more efficient way to deploy the point-to-multipoint
services, such as mobile TV.
This feature can be activated only after MBMS basic functions are enabled. For details, see the
section "Configuring MBMS Introduction Package".
The CN specifies whether broadcast mode or enhanced broadcast mode is used for MBMS
services. If the CN specifies the enhanced broadcast mode and the license for this mode is
activated, then, enhanced broadcast mode is used. The MBMS transmission mode should be
configured on the RNC.
The MBMS transmission mode can be configured at the SA level, RNC level, or cell level. The
cell level has the highest priority, while the RNC level has the lowest priority. That is, if the
MBMS transmission mode is configured at both the RNC level and the cell level, the cell level
configuration takes effect in the corresponding cell. The detailed process is as follows:
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET URNCMBMSPARA (CME single
configuration: UMTS Radio Global Configuration Express > MBMS
Configuration > MBMS Parameter in RNC Level; CME batch modification center:
3.15 Modifying RNC Parameters in Batches) to set the transmission mode at the
RNC level through the Mbms Transfer Mode parameter.
2. Optional: Run the BSC6900 MML command ADD USAMBMSPARA (CME single
configuration: UMTS Radio Global Configuration Express > MBMS
Configuration > MBMS Parameter in SA Level; CME batch modification center:
not supported) to set the transmission mode at the SA level through the Mbms
Transfer Mode parameter.
3. Optional: Run the BSC6900 MML command ADD UCELLMBMSPARA (CME
single configuration: UMTS Cell Configuration Express > MBMS
Configuration > MBMS Parameter in Cell Level; CME batch modification center:
3.18 Modifying UMTS Cell Parameters in Batches) to set the transmission mode
at the cell level through the Mbms Transfer Mode parameter.
4. Run the BSC6900 MML command SET URNCMBMSPARA (CME single
configuration: UMTS Radio Global Configuration Express > MBMS
Configuration > MBMS Parameter in RNC Level; CME batch modification center:
3.15 Modifying RNC Parameters in Batches) to set the transfer threshold between
PtP and PtM mode through the Counting Threshold and the Ptp To Ptm Offset
parameters.
l Verification Procedure
1. Use an MBMS-supportive UE to request an MBMS service and receive the
corresponding data.
2. Check MBMS SESSION START message traced on the Iu interface at the RNC. If
the value of the MBMS Bearer Service Type IE is broadcast and the value of MBMS
Counting Information IE is counting, the enhanced broadcast mode is configured.
3. Use one or two MBMS-supportive UEs to receive the MBMS service, you can find
that the DCH or HS-DSCH is used. Use three MBMS-supportive UEs to receive the
MBMS service, you can find that the FACH is used.
l Deactivation Procedure
To deactivate this feature, switch off the license item of the feature.
----End
Example
//Activating MBMS Enhanced Broadcast Mode
SET URNCMBMSPARA: MbmsTransMode= DYNAMIC;
ADD USAMBMSPARA: CnOpIndex=0, MbmsSaId=0, MbmsTransMode= DYNAMIC;
ADD UCELLMBMSPARA: CellId=100, MbmsTransMode= DYNAMIC;
SET URNCMBMSPARA: NCountingThd=2, NPtpToPtmOffset=1;
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01066002 MBMS P2P over HSDPA.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
The features WRFD-010616 MBMS Introduction Package and WRFD-010610 HSDPA
Introduction Package must be configured before this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature enables Multimedia Broadcast and Multicast Service point-to-point (MBMS P2P)
services to be carried on the HS-DSCH, saving cell resources.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET URNCMBMSPARA (CME single
configuration: UMTS Radio Global Configuration Express > MBMS
Configuration > MBMS Parameter in RNC Level; CME batch modification center:
3.15 Modifying RNC Parameters in Batches). In this step, set Mbms Transfer
Mode to DYNAMIC.
2. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, set Service Mapping Strategy Switch to
MAP_PS_STREAM_ON_HSDPA_SWITCH.
l Verification Procedure
Example
//Activating MBMS P2P over HSDPA
SET URNCMBMSPARA: MbmsTransMode= DYNAMIC;
SET UCORRMALGOSWITCH: MapSwitch=MAP_PS_STREAM_ON_HSDPA_SWITCH-1;
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01066003 MBMS Admission Enhancement.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
The feature WRFD-010616 MBMS Introduction Package must be configured before
this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature provides different admission policies for Multimedia Broadcast and Multicast
Service point-to-multipoint (MBMS PTM) services and MBMS point-to-point (MBMS PTP)
services. MBMS PTP services use the same admission, preemption, and congestion criteria with
normal services except MBMS HSDPA services. MBMS PTM services should be treated
differently so that they do not occupy excessive resources to block non-MBMS connection
admission. In addition, some resources should be reserved for MBMS PTM services.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UQUEUEPREEMPT (CME single
configuration: UMTS Radio Global Configuration Express > Queue Preempt
Parameters Configuration > RNC Oriented Queue Preempt Algorithm
Parameters; CME batch modification center: 3.15 Modifying RNC Parameters in
Batches) to set Mbms PreemptAlgoSwitch and Preempt algorithm switch to
ON.
Example
//Activating MBMS Admission Enhancement
SET UQUEUEPREEMPT: PreemptAlgoSwitch=ON, MbmsPreemptAlgoSwitch=ON;
SET URNCMBMSPARA: MbmsTransMode=PTM, PtmPreemptSwitch=ON,
PtmStrmPasiSwitch=ON, PtmNullStrmPasiSwitch=ON;
83 Configuring Inter-Frequency
Neighboring Cell Selection for MBMS PTP
Users
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01066004 Inter-Frequency Neighboring Cell Selection for MBMS PTP Users.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
The configurations of the features on which this feature depends are complete. This
feature depends on the feature WRFD-010616 MBMS Introduction Package,
WRFD-010660 MBMS Phase 2.
l License
This feature is not under license control.
Context
This feature enables the filtering and handover of a target cell based on the MBMS channel
resources in the inter-frequency neighboring cells, therefore ensuring the continuity of the
MBMS service.
Procedure
l Activation Procedure
The feature does not need to be activated.
l Verification Procedure
This feature does not need to be verified.
l Deactivation Procedure
This feature does not need to be deactivated.
----End
This section describes how to activate, verify, and deactivate the optional feature WRFD-010627
FACH Transmission Sharing for MBMS.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The feature WRFD-010616 MBMS Introduction Package has been configured before
this feature is activated.
l License
This feature is not under license control.
Context
This feature enables the FACHs that carry MBMS services to share transport resources over the
Iub interface, thereby saving the Iub bandwidth.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UMBMSSWITCH (CME single
configuration: UMTS Radio Global Configuration Express > MBMS
Configuration > MBMS Switch; CME batch modification center: 3.15 Modifying
RNC Parameters in Batches). In this step, set MBMS Iub Sharing Switch to ON
(ON).
l Verification Procedure
1. Before turning on the transmission sharing switch, activate the MBMS services in two
cells served by the same NodeB. View the tracing messages over the Iub interface.
You may find two pairs of COMMON TRANSPORT CHANNEL SETUP
REQUEST/COMMON TRANSPORT CHANNEL SETUP RESPONSE messages,
where the BROADCAST REFERENCE IEs in the two COMMON TRANSPORT
CHANNEL SETUP REQUEST messages are different. This indicates that the
messages are transmitted over different Iub interfaces.
2. Turn on the transmission sharing switch, activate the MBMS services in two cells
served by the same NodeB, and view the tracing messages over the Iub interface.
You may find two pairs of COMMON TRANSPORT CHANNEL SETUP
REQUEST/COMMON TRANSPORT CHANNEL SETUP RESPONSE messages,
where the BROADCAST REFERENCE IEs in the two COMMON TRANSPORT
CHANNEL SETUP REQUEST messages are the same. This indicates that the
messages are transmitted over the same Iub interface. This feature has been activated.
l Deactivation Procedure
1. Run the BSC6900 MML command SET UMBMSSWITCH (CME single
configuration: UMTS Radio Global Configuration Express > MBMS
Configuration > MBMS Switch; CME batch modification center: 3.15 Modifying
RNC Parameters in Batches). In this step, set MBMS Iub Sharing Switch to OFF
(OFF).
----End
Example
//Activating FACH Transmission Sharing for MBMS
SET UMBMSSWITCH: MbmsSwitch=ON, MbmsIubSharingSwitch=ON;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010626
MBMS FLC(Frequency Layer Convergence)/FLD(Frequency Layer Dispersion).
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The feature WRFD-010616 MBMS Introduction Package has been configured before
this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others Prerequisites
UEs support this feature.
Context
Frequency Layer Convergence (FLC) denotes the process where the UTRAN requests UEs to
preferentially reselect to the frequency layer on which the MBMS service is intended to be
transmitted.
Frequency Layer Dispersion (FLD) denotes the process where the UTRAN redistributes UEs
across frequencies.
FLC helps users obtain the information about an MBMS service in real time. FLD reduces cell
load after the MBMS service is finished.
FLD is activated automatically after FLC takes effect, and is deactivated automatically after
FLC is disabled.
Procedure
l Activation Procedure
NOTE
Two overlapping cells covered by multiple carriers must be enabled with MBMS.
The cell using frequency F1 is in the SA of MBMS, and other cells using other frequencies are not
in the SA of MBMS.
1. Run the BSC6900 MML command MOD UCELLMCCH (CME single
configuration: UMTS Cell Configuration Express > Channel Configuration >
Configuration of the MCCH And MICH; CME batch modification center: not
supported). In this step, set Flc Algo Switch to ON(ON).
2. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, select the
HO_ALGO_MBMS_FLC_SWITCH check box under the parameter HandOver
Switch.
l Verification Procedure
1. Configure an MCCH in an R99 cell and set an MBMS cell to the neighboring cell of
the R99 cell.
2. Make UEs camp on the R99 cell, activate the MBMS service, and accept the MBMS
service.
If UEs are reselected to the MBMS cell successfully and transmit and receive data
normally, FLC is activated.
3. Move UEs to the MBMS cell edge and terminate the MBMS service.
If some UEs are reselected to the R99 cell, FLD is activated.
l Deactivation Procedure
1. Run the BSC6900 MML command MOD UCELLMCCH (CME single
configuration: UMTS Cell Configuration Express > Channel Configuration >
Configuration of the MCCH And MICH; CME batch modification center: not
supported). In this step, set Flc Algo Switch to OFF(OFF).
2. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, deselect the
HO_ALGO_MBMS_FLC_SWITCH check box under the parameter HandOver
Switch.
----End
Example
//Activating MBMS FLC(Frequency Layer Convergence)/FLD(Frequency Layer
Dispersion)
MOD UCELLMCCH: CellId=1, FlcAlgoSwitch=ON;
SET UCORRMALGOSWITCH: HoSwitch=HO_ALGO_MBMS_FLC_SWITCH-1;
//Deactivating MBMS FLC(Frequency Layer Convergence)/FLD(Frequency Layer
Dispersion)
This section describes how to activate, verify, and deactivate the optional feature WRFD-010661
MBMS over Iur.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The feature WRFD-010660 MBMS Phase 2 has been configured before this feature is
activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The neighboring RNC supports the MBMS feature.
The Point to Point (PTP) services are supported.
Context
This feature extends the application scope of the MBMS service.
Procedure
l Activation Procedure
This feature does not need to be activated. It takes effect after the feature WRFD-010616
MBMS Introduction Package is activated.
l Verification Procedure
Initiate a softt handover by moving a UE that is in CELL_DCH state and receiving the
MBMS data in PTP mode from the Serving RNC (SRNC) to the Drift RNC (DRNC). In
this way, a Radio Link (RL) is established on the Iur interface. The cell to which the RL
belongs performs the MBMS service in Point to Multipoint (PTM) mode. If at the time
being the UE under the DRNC is receiving only MBMS data in PTM mode, this feature
has been activated.
l Deactivation Procedure
This feature does not need to be deactivated.
----End
This section describes how to activate, verify, and deactivate the optional feature WRFD-010662
Dynamic Power Estimation for MTCH.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The feature WRFD-010660 MBMS Phase 2 has been configured before this feature is
activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature enables dynamic adjustment of the transmit power of the MTCH based on the
number of neighboring cells that are in PTM mode.
It does not conflict with the maximum power and minimum power defined in the MBMS service.
In addition, this feature depends on the MBMS service, because it introduces only power
deviation.
Procedure
l Activation Procedure
This feature does not need to be activated. Telecom operators only need to set the power
adjustment threshold to an appropriate value.
1. Run the BSC6900 MML command SET URNCMBMSPARA (CME single
configuration: UMTS Radio Global Configuration Express > MBMS
Configuration > MBMS Parameter in RNC Level; CME batch modification center:
3.15 Modifying RNC Parameters in Batches). In this step, set Combine Neighbour
Cell Percent to an appropriate value based on the network plan. When the rate of
PTM applications in a cell in PTM mode reach the value of this parameter, this feature
brings a combining gain. If Combine Neighbour Cell Percent is set to a small value,
the transmit power of the MBMS SCCPCH in the cell decreases.
l Verification Procedure
1. Select two MBMS cells (cell A and cell B) that work in the same frequency. In cell
A, configure only cell B as its intra-frequency neighboring cell. Apply the PTM mode
in cell A and PTP mode in cell B.
2. Use an MBMS-capable UE to initiate an MBMS service in cell A. View the
NBAP_COMM_TRANSP_CH_SETUP_REQ message traced on the Iub interface to
check the power of the FACH that carries the service.
3. Set cell B to send MBMS data in the same channel in PTM mode. In this manner, the
rate of the intra-frequency neighboring cells that apply the PTM mode exceeds the
value of the preset Combine Neighbour Cell Percent.
4. View the NBAP_COMM_TRANSP_CH_SETUP_REQ message traced on the Iub
interface to check the power of the FACH that carries the service.
Expected result: The power of the FACH that carries data of the MBMS channel
decreases by 5 dB.
l Deactivation Procedure
This feature does not need to be deactivated.
----End
Example
//Setting the Power Adjusting Threshold
SET URNCMBMSPARA: CombNCellPercent=50;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010663
MSCH Scheduling.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The feature WRFD-010616 MBMS Introduction Package has been configured before
this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature enables a UE to receive packets on the MTCH in Discontinuous Reception (DRX)
mode, thereby reducing UE power consumption.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UMBMSSWITCH (CME single
configuration: UMTS Radio Global Configuration Express > MBMS
Configuration > MBMS Switch; CME batch modification center: 3.15 Modifying
RNC Parameters in Batches). In this step, set both Msch Switch For
NonMtchMulti Sccpch and Msch Switch For MtchMulti Sccpch to ON(ON).
l Verification Procedure
1. Use an MBMS-capable UE to initiate an MBMS service and ensure that the UE can
receive the MBMS data.
2. Check messages traced on the Uu interface. If MSCH configuration information is
found in the MBMS CURRENT CELL P-T-M RB INFORMATION, MBMS
GENERAL INFORMATION, and MBMS NEIGHBOURING CELL P-T-M RB
INFORMATION messages, this feature has been activated.
l Deactivation Procedure
1. Run the BSC6900 MML command SET UMBMSSWITCH (CME single
configuration: UMTS Radio Global Configuration Express > MBMS
Configuration > MBMS Switch; CME batch modification center: 3.15 Modifying
RNC Parameters in Batches). In this step, set both Msch Switch For
NonMtchMulti Sccpch and Msch Switch For MtchMulti Sccpch to OFF(OFF).
----End
Example
//Activating MSCH scheduling
SET UMBMSSWITCH: MbmsSwitch=ON, MschSwitchForNonMtchMulti=ON,
MschSwitchForMtchMulti=ON;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010665
MBMS Channel Audience Rating Statistics.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The feature WRFD-010616 MBMS Introduction Package has been configured before
this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The BMSC on the CN side identifies the channel with a fixed Temporary Mobile Group
Identity (TMGI) when delivering a program source.
Context
This feature enables statistics on MBMS channels to help the operator obtain the audience rating
of the MBMS channels.
Procedure
l Activation Procedure
Set the MBMS channels (a maximum of five MBMS channels can be set) on which statistics
is to be performed. Then, send the TMGIs of these channels from the M2000 to the RNC.
The RNC then measures the following channel-related counters:
This section describes how to activate, verify, and deactivate the optional feature WRFD-020801
Cell ID + RTT Function Based LCS.
Prerequisites
l Dependencies on Hardware
If SAS-CENTRIC locating is required, SAS equipment has been configured.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others Prerequisites
UE is needed to report the relevant measurement results.
CN is needed to trigger the location request.
The UE supports at least one of the following locating methods:
UE-assisted CELLID+RTT locating or UE-based CELLID+RTT locating in RNC-
CENTRIC mode
UE-assisted CELLID+RTT locating in the SAS-CENTRIC mode
Context
The simplest CELLID + Round Trip Time (RTT) locating method is to directly use the
geographical center of the coverage area of the reference cell as the locating result.
To achieve high locating accuracy, the BSC6900 demands RTT measurement in all cells in the
active set and requests the UE to perform locating measurement on the corresponding cells. By
means of the two types of measurement, the BSC6900 calculates the time of arrival (TOA) of
signal from the cell antenna to the UE. By multiplying the TOA by the velocity of light, the
BSC6900 obtains the distance between a certain cell and the UE. If three TOA circles intersect,
the BSC6900 can obtain the accurate location of the UE.
Procedure
l Activation Procedure
1. Optional: If inter-RNC locating is required, the Iur interface needs to be configured.
For details, see 94 Configuring LCS over Iur.
2. Optional: If SAS-CENTRIC mode needs to be supported, the Iupc interface is
required. For details, see 95 Configuring Iupc Interface for LCS Service.
3. Run the BSC6900 MML command SET USMLC (CME single configuration: UMTS
Radio Global Configuration Express > Location Service Parameter
Configuration > SMLC Algorithm Parameters; CME batch modification center:
3.15 Modifying RNC Parameters in Batches) to set the parameters of the SMLC
algorithm. In this step, set UE Positioning Method, CELLID+RTT Method Type,
and Location Working Mode to appropriate values.
4. Run the BSC6900 MML command ADD USMLCCELL (CME single configuration:
UMTS Cell Configuration Express > SMLC and IPDL > Cell SMLC
Information; CME batch modification center: not supported) to set the following
location information parameters of the cell:
Cell location configuration type
Geographical location information about the antenna:
Cell Antenna Latitude
Cell Antenna Altitude
Cell Antenna Longitude
Cell coverage information:
Cell Antenna Max Coverage
Cell Antenna Orientation
Cell Antenna Opening
l Verification Procedure
1. Initiate Iu, Iub, and Uu interface message tracing, as shown in Figure 90-1, Figure
90-2, and Figure 90-3 respectively.
2. Use a UE to access the cell and enable the CN to send a locating request message.
3. The message LOCATION REPORTING CONTROL and LOCATION
REPORT are traced on the Iu interface, as shown in Figure 90-4 and Figure 90-5.
4. The messages traced on the Iub interface show that the procedure Dedicated
Measurement Initiation is performed on all links in the active set and that the value
of Dedicated Measurement Type is Round Trip Time, as shown in Figure 90-6
and Figure 90-7.
5. From the traced Uu interface messages, you can see the information about the UE Rx-
Tx time difference measurement, which is a type of internal measurement (if the UE
supports UE Rx-Tx time difference type 2 measurement, the locating method for Rx-
Tx time difference type 2 measurement is adopted), as shown in Figure 90-8 and
Figure 90-9.
l Deactivation Procedure
1. Run the BSC6900 MML command SET USMLC (CME single configuration: UMTS
Radio Global Configuration Express > Location Service Parameter
Configuration > SMLC Algorithm Parameters; CME batch modification center:
3.15 Modifying RNC Parameters in Batches) to deactivate the CELLID+RTT
locating method. In this step, deselect the CELLID_RTT check box under parameter
UE Positioning Method.
----End
Example
//Activating Cell ID + RTT Function Based LCS
//Setting the parameters of the SMLC algorithm
SET USMLC: SmlcMethod=CELLID_CENTER-0&CELLID_RTT-1&OTDOA-0&AGPS-0,
CELLIDRTTMethodType=UE_ASSISTED, ForcedSHOSwitch=OFF,
IntraRelThdFor1A=2, IntraRelThdFor1B=2, TrigTime1A=D10, TrigTime1B=D10,
SHOQualmin=-20, LcsWorkMode=RNC_CENTRIC;
This section describes how to activate, verify, and deactivate the optional feature WRFD-020802
OTDOA Based LCS.
Prerequisites
l Dependencies on Hardware
The corresponding NodeBs should be equipped USCU card with GPS function.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others Prerequisites
UE is needed to report the relevant measurement results.
CN is needed to trigger the location request.
The UE supports at least one of the following positioning methods:
UE-based OTDOA positioning method
UE-assisted OTDOA positioning method
Context
Huawei UTRAN supports IPDL-OTDOA location services. In this feature, the NodeB is
configured with a GPS card and supports cell frame timing measurement. In addition,
BSC6900 initiates and traces the SFN-SFN observed time difference measurement. BSC6900
calculates the relative time difference (RTD) of the cell related to positioning based on the latest
measurement reports (MRs).
Procedure
l Activation Procedure
1. Optional: Configure the Iur interface if inter-RNC locating is required. For details,
see 94 Configuring LCS over Iur.
2. Run the BSC6900 MML command SET USMLC (CME single configuration: UMTS
Radio Global Configuration Express > Location Service Parameter
Configuration > SMLC Algorithm Parameters; CME batch modification center:
3.15 Modifying RNC Parameters in Batches) to set the SMLC algorithm
parameters. In this step, set UE Positioning Method and Location Working Mode
to appropriate values.
NOTE
Example
//Activating OTDOA Based LCS
//Setting the parameters for the SMLC algorithm
SET USMLC: SmlcMethod=OTDOA-1, OTDOAMethodType=UE_BASED,
LcsWorkMode=RNC_CENTRIC;
This section describes how to activate, verify, and deactivate the optional feature WRFD-020803
A-GPS Based LCS. (This feature cannot be configured using the CME. )
Prerequisites
l Dependencies on Hardware
If GPS receiver is located at RNC,BSC6900 needs clock board such as GCGa to support
this feature.
If GPS receiver is located at NodeB, NodeB should be equipped with USCU card with
GPS function.
When the RNC-CENTRIC locating service is required:
If a Global Positioning System (GPS) receiver is configured on the BSC6900 side,
the BSC6900 must be configured with the General Clock Unit with GPS REV:a
(GCGa) board.
If a GPS receiver is configured on the NodeB side, the NodeB must be configured
with the Universal Satellite card and Clock Unit (USCU) and WCDMA GPS
Receiving Unit (WGRU), and all the equipment (including the GPS antenna system)
must be properly installed and connected.
When the SAS-CENTRIC locating service is required, the BSC6900 must be configured
with a Stand-Alone SMLC (SAS) device. SMLC refers to Serving Mobile Location
Center.
NOTE
If A-GPS positioning is required, the GPS receiver does not need to be installed in BSC6900 side
or NodeB side.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
NodeB V200R014 supports this feature while NodeB V100R014 does not support this
feature.
Context
A-GPS positioning is an application of GPS positioning in the WCDMA network. In open areas,
A-GPS positioning can provide high positioning sensitivity, shorten positioning time, and save
power.
The location information about the GPS receiver can be automatically searched by the GPS
receiver itself or be configured by a user.
l If the accurate location information (to be provided by the surveying and mapping
authorities) about the antenna of the GPS receiver can be obtained, it is recommended that
the information be specified when the GPS receiver is being configured. In this way, the
GPS receiver can quickly search for the satellite group in the area where it is located, and
accurately calculate the differential GPS information.
l If the accurate location information about the antenna of the GPS receiver cannot be
obtained, the auto search mode can be selected.
Procedure
l Activation Procedure
NOTE
The BSC6900 and NodeB must be configured with the related data to activate this feature.
NOTE
In RNC-CENTRIC mode, a GPS receiver can be configured on the NodeB side as required. If a GPS
receiver is configured on the NodeB side, the NodeB must be configured with the USCU and WGRU,
and all the equipment (including the GPS antenna system) must be properly installed and connected.
1. Run the NodeB MML command ADD BRD to add a USCU board.
Set Cabinet No., Subrack No., and Slot No. to appropriate values based on the
actual location of the USCU board.
Set Board Type to USCU.
2. Run the NodeB MML command SET CLKMODE to set the working mode of the
reference clock source.
3. Run the NodeB MML command ADD GPS to add a GPS clock link.
4. Run the NodeB MML command MOD GPSPOS to add a GPS receiver.
If Way to Get Position is set to USER_CONFIG(User Config), set Antenna
Longitude, Antenna Latitude, and Antenna Altitude to appropriate values.
If Way to Get Position is set to SEARCH_WITH_DURATION(Search with
duration), set Duration to an appropriate value.
If Way to Get Position is set to SEARCH_WITH_PRECISION(Search with
precision), set Precision to an appropriate value.
l Verification Procedure
Verification Procedure on the BSC6900 Side
1. Initiate Iu and Uu interface tracing, as shown in Figure 92-1 and Figure 92-2
respectively.
2. Make a UE access the network and enable the CN to send a positioning request.
3. Over the Iu interface, you can view the Location Reporting Control and Location
Report messages, as shown in Figure 92-3 and Figure 92-4.
4. The Uu interface tracing messages contain the information about A-GPS positioning
measurement, as shown in Figure 92-5 and Figure 92-6.
Example
/*Activating A-GPS Based LCS*/
This section describes how to activate, verify, and deactivate the optional feature WRFD-020804
LCS Classified Zones.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The core network (CN) supports this feature.
Context
This feature defines a classified zone. Once the UE enters or exits the zone, the RNC
automatically reports the service area identity (SAI) of the UE.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command ADD UCZ (CME single configuration: UMTS
Global Configuration Express > Area Information Configuration > Classified
Zone Information; CME batch modification center: not supported) to add a classified
zone.
NOTE
l In this step, you need to set the parameters Cn Operator Index, Location Area Code,
Service Area Code, and Classified Zone ID. More than one classified zone can be set for
each operator.
l Before running the ADD UCZ (CME single configuration: UMTS Global Configuration
Express > Area Information Configuration > Classified Zone Information; CME batch
modification center: not supported) command, ensure that Location Area Code and
Service Area Code are configured at the local RNC. Otherwise, the classified zone cannot
be configured.
l Verification Procedure
1. Initiate Iub interface message tracing on the BSC6900 LMT, as shown in Figure
93-1.
2. Enable the UE to establish a service of any type. Move the UE from cell A (whose
LAC and SAC are 9513 and 272 respectively) to cell B (whose LAC and SAC are
9514 and 273 respectively), to add cell B to the active set.
If a LOCATION REPORT message is displayed, this feature has been activated.
If the value of the information element (IE) "Cause" in the LOCATION REPORT
message is "User Restriction Start Indication", the UE enters the classified zone.
The SAI of the UE is also contained in the message, as shown in Figure 93-2.
3. Remove cell B from the active set by performing a handover or Serving Radio Network
Subsystem (SRNS) relocation.
If a LOCATION REPORT message is displayed, this feature has been activated.
If the cause value of the LOCATION REPORT message is displayed as "User
Restriction End Indication", the UE exits the classified zone. The SAI of the UE
is also contained in the LOCATION REPORT message.
l Deactivation Procedure
1. Run the BSC6900 MML command RMV UCZ (CME single configuration: UMTS
Global Configuration Express > Area Information Configuration > Classified
Zone Information; CME batch modification center: not supported) to remove the
classified zone from all operators at the RNC.
----End
Example
//Activating LCS Classified Zone
This section describes how to activate, verify, and deactivate the optional feature WRFD-020805
LCS over Iur.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The following feature has been configured before this feature is activated:
WRFD-020801 Cell ID + RTT Function Based LCS or WRFD-020803 A-GPS Based
LCS.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others Prerequisites
The UE and the neighboring RNC (NRNC) support this feature.
This feature is used only in RNC-CENTRIC mode.
Context
This feature enables Huawei RAN to provide location services (LCS) over the Iur interface,
extending the LCS area. It enables exchange of cell information and GPS assistance information
over the Iur interface.
Procedure
l Activation Procedure
NOTE
In this procedure, you need to set the positioning method and add the geographical information about
the cell at the RNC. For cell information exchange over the Iur interface, geographical information
about a neighboring cell must be configured at the NRNC.
1. Run the BSC6900 MML command SET USMLC (CME single configuration: UMTS
Radio Global Configuration Express > Location Service Parameter
Configuration > SMLC Algorithm Parameters; CME batch modification center:
l If a GPS receiver on the NRNC side is installed on the NodeB, set GPS type to
NRNC_NODEB(NodeB in RNC).
l Before adding a GPS receiver to the NRNC, ensure that the GPS receiver is installed
at the NRNC. Run the BSC6900 MML command ADD GPS (CME single
configuration: UMTS Global Configuration Express > Device Configuration >
GPS Reference Receiver; CME batch modification center: not supported) to add
the GPS receiver. In this step, set GPS type to RNC(Local RNC) (when the GPS
receiver is installed at the RNC) or to NODEB(Local NodeB) (when the GPS
receiver is installed at the NodeB).
c. If a GPS receiver needs to be configured on the BSC6900 side, run the BSC6900
MML command SET CLKTYPE (CME single configuration: UMTS Global
Configuration Express > Device Configuration > Clock Board Type; CME
batch modification center: 3.15 Modifying RNC Parameters in Batches) with
the type of clock board in the BSC6900 set to GCGa.
d. Run the BSC6900 MML command ACT GPS (CME single configuration:
UMTS GLOBAL Configuration Express > Device Configuration > GPS
Reference Receiver. Set GPS Active Flag to Activated; CME batch
modification center: not supported) to activate the GPS reference receiver.
e. Optional: Run the BSC6900 MML command ADD
UCELLGPSFRMTIMING (CME single configuration: UMTS Cell
Configuration Express > SMLC and IPDL > Cell GPS Frame Timing; CME
batch modification center: 3.18 Modifying UMTS Cell Parameters in
Batches) to set parameters related to UTRAN GPS cell frame timing
measurement to appropriate values. In this step, set Cell ID and GPS Frame
Timing Active Flag.
l Verification Procedure
1. Start Iur interface tracing on the BSC6900 LMT, as shown in Figure 94-1.
2. Check the information traced over the Iur interface. You can find an information
exchange initiation procedure. In this procedure, the local RNC sends the NRNC an
INFORMATION EXCHANGE INITIATION REQUEST message, in which the
value of Information Type is GPS Information or DGPS. The NRNC sends the
local RNC INFORMATION EXCHANGE INITIATION RESPONSE and
INFORMATION REPORT messages, which contain GPS assistance data, as shown
in Figure 94-2.
Figure 94-2 GPS assistance data carried in the INFORMATION REPORT message
NOTE
You can see INFORMATION EXCHANGE INITIATION REQUEST and
INFORMATION EXCHANGE INITIATION RESPONSE messages only after the
BSC6900 MML command ACT GPS is executed.
3. Establish a service, and then perform a soft handover over the Iur interface.
4. Enable the CN to send a LOCATION REPORTING CONTROL message with the
cause "DIRECT".
5. Check messages traced over the Iur interface. You can find an Information Exchange
Initiation procedure. In this procedure, the local RNC sends the NRNC an
INFORMATION EXCHANGE INITIATION REQUEST message, in which the
value of Information Type is UTRAN Access Point Position with Altitude, as
shown in Figure 94-3. The NRNC sends the local RNC an INFORMATION
EXCHANGE INITIATION RESPONSE message, which contains geographical
information about the neighboring cell over the Iur interface, as shown in Figure
94-4.
6. Check messages traced over the Iur interface. You can find DEDICATED
MEASUREMENT INITIATION REQUEST and DEDICATED
MEASUREMENT INITIATION RESPONSE messages, as shown in Figure
94-5 and Figure 94-6 respectively. In the former message, the value of Dedicated
Measurement Type is Round Trip Time.
l Deactivation Procedure
1. Run the BSC6900 MML command DEA GPS (CME single configuration: UMTS
GLOBAL Configuration Express > Device Configuration > GPS Reference
Receiver. Set GPS Active Flag to Deactivated; CME batch modification center: not
supported) to deactivate the GPS receiver. Alternatively, run the BSC6900 MML
command RMV GPS (CME single configuration: UMTS Global Configuration
Express > Device Configuration > GPS Reference Receiver; CME batch
modification center: not supported) to remove the GPS receiver from the NRNC. GPS
information exchange over the Iur interface is thereby disabled.
2. Run the BSC6900 MML command RMV UIURCOMMSCCP (CME single
configuration: UMTS Global Configuration Express > RNC Basic
Configuration > Information of IUR Common SCCP Connection; CME batch
modification center: not supported) to deactivate LCS over Iur.
----End
Example
/*Activating LCS over Iur*/
//Setting the positioning method
SET USMLC: SmlcMethod=CELLID_RTT-1&OTDOA-0&AGPS-0;
/*Configuring cell information exchange over the Iur interface*/
ADD UIURCOMMSCCP: SRN=0, SN=1;
ADD USMLCCELL: RNCId=29, CellId=1, CellLocCfgType=CELL_ANTENNA, GCDF=DEG,
MTRLGY=MET, AntennaLatitudeDegree=31245560,
AntennaLongitudeDegree=121588234, AntennaAltitudeMeter=20,
MaxAntennaRange=2000, AntennaOrientation=0, AntennaOpening=1200;
CellAverageHeight=25;
/*Configuring GPS assistance information exchange.*/
ADD UIURCOMMSCCP: SRN=0, SN=1;
ADD GPS: AGPSRECEIVERID=0, AGPSRECEIVERTYPE=NRNC_RNC, RNCID=1, GCDF=DEG,
MTRLGY=MET, LATITUDE=31245560, LONGITUDE=121588230, ALTITUDE=21;
SET CLKTYPE: CLKTYPE=GCGa;
ACT GPS: AGPSRECEIVERID=0, ACTTYPE=BOTH;
ADD UCELLGPSFRMTIMING: CellId=1, StartFlag=ACTIVE;
This section describes how to activate, verify, and deactivate the optional feature WRFD-020807
Iupc Interface for LCS service.
Prerequisites
l Dependencies on Hardware
IP interface boards of the BSC6900 support this feature.
A Stand-Alone SMLC (SAS) is configured.
l Dependencies on Other Features
The following features have been configured before this feature is activated:
WRFD-020801 Cell ID + RTT Function Based LCS has been configured if the
operator employs the Cell ID+RTT algorithm.
WRFD-020803 A-GPS Based LCS has been configured if the operator employs the
A-GPS algorithm.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The UE supports at least one of the following positioning methods:
UE-assisted CELLID+RTT
UE-based A-GPS
UE-assisted A-GPS
The global data is configured by performing the following procedure:
1. Configuring the Basic Data
2. Configuring the OSP and DSP
3. Configuring the Area Information
4. Configuring the M3UA Local and Destination Entities
Physical layer data and data link layer data are configured by performing the following
procedure:
1. Configuring the Physical Layer and Data Link Layer for the FG2a/FG2c/GOUa/
GOUc Board
2. Configuring the Physical Layer and Data Link Layer for the PEUa Board
3. Configuring the Physical Layer and Data Link Layer for the POUa/POUc Board
4. Configuring the User Plane of the Iub Interface (over ATM)
Context
Only IP transmission can be applied between the BSC6900 and the SAS. The transport network
layer data on the Iupc interface needs to be configured at the BSC6900. When the BSC6900 is
connected to multiple SASs through IP transmission, you need to configure this feature on each
Iupc interface. One BSC6900 can be connected to a maximum of four SASs simultaneously.
NOTE
Before configuring the Iupc interface data, familiarize yourself with Protocol Structure and Links on the
Iupc Interface.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command ADD N7DPC (CME single configuration: UMTS
Global Configuration Express > Signaling Configuration > DSP Of DPU; CME
batch modification center: not supported) to add the destination signaling point (DSP)
data that corresponds to the SAS.
2. Run the BSC6900 MML commands ADD M3LE (CME single configuration: UMTS
Global Configuration Express > Signaling Configuration > M3UA Local
Entity; CME batch modification center: not supported) and ADD M3DE (CME single
configuration: UMTS Global Configuration Express > Signaling Configuration >
M3UA Destination Entity; CME batch modification center: not supported) to add
the M3UA local entity (M3LE) and the M3UA destination entity (M3DE) that
correspond to the SAS respectively.
3. Run the BSC6900 MML command ADD SCTPLNK (CME single configuration:
IUPC Configuration Express > IP Transport > SCTP Link; CME batch
modification center: not supported) to add an SCTP link. To add multiple SCTP links,
run this command for each SCTP link to be added.
If Signalling link mode is set to Server at the SAS, set Signalling link mode to
CLIENT at the BSC6900. If Signalling link mode is set to CLIENT at the SAS,
set Signalling link mode to Server at the BSC6900.
Set Application type to M3UA.
4. Run the BSC6900 MML command ADD M3LKS (CME single configuration: IUPC
Configuration Express > IP Transport > M3UA Link Set; CME batch modification
center: not supported) to add an M3UA link set.
If Local entity type is set to M3UA_IPSP, set Work mode of the M3UA link set
to M3UA_IPSP.
If Local entity type is set to M3UA_ASP and Destination entity type is set to
M3UA_SP, set Work mode to M3UA_IPSP. If Local entity type is set to
M3UA_ASP and Destination entity type is not set to M3UA_SP, set Work
mode to M3UA_ASP.
5. Run the BSC6900 MML command ADD M3RT (CME single configuration: IUPS
Configuration Express > IP Transport > M3UA Route; CME batch modification
center: not supported) to add an M3UA route.
6. Run the BSC6900 MML command ADD M3LNK (CME single configuration: IUPC
Configuration Express > IP Transport > M3UA Link Set; CME batch modification
center: not supported) to add an M3UA link. To add more M3UA links, run this
command repeatedly.
7. Run the BSC6900 MML command ADD USAS (CME single configuration: UMTS
Global Configuration Express > Radio Basic Data Configuration > Stand-alone
SMLC; CME batch modification center: not supported) to add the SAS.
8. Run the BSC6900 MML command SET USMLC (CME single configuration: UMTS
Radio Global Configuration Express > Location Service Parameter
Configuration > SMLC Algorithm Parameters; CME batch modification center:
3.15 Modifying RNC Parameters in Batches) to enable SAS-CENTRIC positioning
based on CELLID + RTT or AGPS. For details, see 90 Configuring Cell ID + RTT
Function Based LCS or 92 Configuring A-GPS Based LCS.
l Verification Procedure
1. Perform the verification procedures by referring to 90 Configuring Cell ID + RTT
Function Based LCS or 92 Configuring A-GPS Based LCS.
l Deactivation Procedure
1. Perform the deactivation procedures by referring to 90 Configuring Cell ID + RTT
Function Based LCS or 92 Configuring A-GPS Based LCS.
----End
Example
//Activating Iupc Interface for LCS Service
//Adding the DSP data that corresponds to the SAS
ADD N7DPC:DPX=4, SPDF=WNF, DPC=8345, STP=OFF, SLSMASK=B0000,
NEIGHBOR=YES, NAME="SAS", DPCT=IUPC, PROT=ITUT, BEARTYPE=M3UA, SPX=4;
//Adding the M3LE that corresponds to the SAS
ADD M3LE:LENO=0, ENTITYT=M3UA_IPSP, RTCONTEXT=4294967295, NAME="IUPC",
SPX=4;
//Adding the M3DE that correspond to the SAS
ADD M3DE:DENO=0, LENO=0, DPX=4, ENTITYT=M3UA_IPSP, RTCONTEXT=4294967295,
NAME="IUPC";
//Adding an SCTP link
ADD SCTPLNK: SRN=0, SN=0, SCTPLNKN=0, MODE=SERVER, APP=M3UA,
LOCIP1="10.10.10.10", PEERIP1="10.10.11.11", PEERPN=3000, LOGPORTFLAG=NO,
VLANFLAG1=DISABLE, VLANFlAG2=DISABLE, SWITCHBACKFLAG=YES;
//Adding an M3UA link set
ADD M3LKS: SIGLKSX=0, DENO=0, NAME="IUPC";
//Adding an M3UA route
ADD M3RT: DENO=0, SIGLKSX=0, NAME="IUPC";
//Adding an M3UA link
ADD M3LNK: SIGLKSX=0, SIGLNKID=0, SRN=0, SN=0, SCTPLNKN=0, NAME="IUPC";
//Adding the SAS
ADD USAS: CnOpIndex=0, SasId=0, Dpx=4;
//Setting SMLC-related parameters
SET USMLC: SmlcMethod=CELLID_RTT-1, AGPSMethodType=UE_ASSISTED,
LcsWorkMode=SAS_CENTRIC;
This section describes how to activate, verify, and deactivate the optional feature WRFD-020134
Push to Talk. (This feature cannot be configured using the CME. )
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The following features have been configured before this feature is activated:
WRFD-010610 HSDPA Introduction Package, WRFD-010612 HSUPA Introduction
Package, WRFD-010688 Enhanced CELL_FACH, and WRFD-010636 SRB over
HSUPA.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
NOTE
Context
This feature is a part of the end-to-end push to talk (PTT) solution. Implementation of the PTT
solution requires support from the UE, RAN, CN, and PTT server. Huawei RAN can identify
PTT services and implement techniques to reduce the delay in setting up calls of PTT services.
Procedure
l Activation Procedure
----End
Example
//Activating Push to Talk
SET UCORRMALGOSWITCH:CfgSwitch=CFG_PTT_SWITCH-1;
SET UFRC:PTTArpPriorityLevel=1, PTTArpPreEmptCap=TRIGGER,
PTTArpPreEmptVuln=NOT_PRE_EMPTABLE, PTTArpQueuingAllowed=ALLOWED,
PTTHsupaTti=EDCH_TTI_10ms;
SET
URRCTRLSWITCH:PROCESSSWITCH=PTT_EARLY_TRANS_SWITCH_OFF-0&PTT_SPEC_LI_SWIT
CH_OFF-0;
SET UCORRMALGOSWITCH:ReservedSwitch0=RESERVED_SWITCH_0_BIT19-1;
SET UFRCCHLTYPEPARA:SrbChlType=HSUPA;
//Deactivating Push to Talk
SET UCORRMALGOSWITCH:CfgSwitch=CFG_PTT_SWITCH-0;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010612
HSUPA Introduction Package.
Prerequisites
l Dependencies on Hardware
The NBBI and the NULP do not support this feature.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The UE should have HSUPA capability.
Context
This feature enables the system to process HSUPA services, therefore increasing the uplink rate
and system throughput. It provides basic functions of HSUPA.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command ADD UCELLHSUPA (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters >
Configuration of HSUPA in Cell; CME batch modification center: 3.18 Modifying
UMTS Cell Parameters in Batches) to add HSUPA functions of a cell.
2. Run the BSC6900 MML command ACT UCELLHSUPA (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters >
Configuration of HSUPA in Cell. Set Cell HSUPA state to Activated; CME batch
modification center: No supported) to activate the HSUPA function of the cell.
NOTE
To ensure that HSUPA services can be set up successfully, HSUPA services must be mapped to the
corresponding AAL2 paths or IP paths. To avoid the affect on ongoing services, you can add new
AAL2 paths or IP paths.
l Verification Procedure
1. Ensure that the HSUPA function of the cell is activated.
Run the BSC6900 MML command DSP UCELL to verify that the HSUPA function
of the cell is activated.
2. Establish a PS service.
The IE E-DCH FDD information in the RL SETUP message on the Iub interface and
the IE rb-mappinginfo in the RRC_RB_SETUP message on the Uu interface should
indicate that the service has been set up and carried on the E-DCH.
l Deactivation Procedure
1. Run the BSC6900 MML command DEA UCELLHSUPA (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters >
Configuration of HSUPA in Cell. Set Cell HSUPA state to Deactivated; CME batch
modification center: No supported) to deactivate the HSUPA function of the cell.
2. Run the BSC6900 MML command RMV UCELLHSUPA (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters >
Configuration of HSUPA in Cell; CME batch modification center: not supported)
to remove the HSUPA functions of a cell.
----End
Example
//Activating HSUPA Introduction Package
ADD UCELLHSUPA: CellId=111;
ACT UCELLHSUPA: CellId=111;
//Verifying HSUPA Introduction Package
DSP UCELL: DSPT=BYCELL, CellId=111;
//Deactivating HSUPA Introduction Package
DEA UCELLHSUPA: CellId=111;
RMV UCELLHSUPA: CellId=111;
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061202 HSUPA Admission Control.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
The feature WRFD-010612 HSUPA Introduction Package must be configured before
this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature enables HSUPA and R99 services to simultaneously access the network by using
the remaining uplink cell load and other resources, improving the utilization of system resources
and ensuring QoS of admitted users.
Procedure
l Activation Procedure
1. Activating Power Resource Admission
a. Run the BSC6900 MML command MOD UCELLALGOSWITCH (CME
single configuration: UMTS Cell Configuration Express > Cell Parameters
> Cell Algorithm Switches; CME batch modification center: 3.18 Modifying
UMTS Cell Parameters in Batches). In this step, select an uplink Call
Admission Control (CAC) algorithm through the parameter Uplink CAC
algorithm switch and a downlink CAC algorithm through the parameter
Downlink CAC algorithm switch.
b. For HSUPA services, run the BSC6900 MML command MOD
UCELLALGOSWITCH (CME single configuration: UMTS Cell
Configuration Express > Cell Parameters > Cell Algorithm Switches; CME
Iub resource admission is unconditionally performed and does not need to be activated.
NOTE
Run the BSC6900 MML command MOD IPPATH (CME single configuration: NodeB
Configuration Express > IUB_RNC > IP Transport > IP Path; CME batch modification
center: not supported) or MOD AAL2PATH (CME single configuration: NodeB
Configuration Express > IUB_RNC > ATM Transport > AAL2 Path; CME batch
modification center: not supported) to modify the Iub bandwidth.
l Verification Procedure
1. UE1 and UE2 are in idle state and camp on CELL_A11. CELL_A11 supports HSUPA.
2. On the HLR, set the PS service type to background or interactive.
3. Run the BSC6900 MML command MOD UCELLCAC to set the maximum number
of HSUPA users supported by CELL_A11 to 1.
4. Establish an HSUPA PS service on UE1, and then check the rb-mappinginfo
information element in the RRC_RB_SETUP message traced over the Uu interface.
The value of ul-TrCH-Type is e-dch.
Example
//Activating power resource admission
MOD UCELLALGOSWITCH: CellId=11, NBMUlCacAlgoSelSwitch=ALGORITHM_FIRST,
NBMDlCacAlgoSelSwitch=ALGORITHM_SECOND;
MOD UCELLALGOSWITCH: CellId=11,
NBMCacAlgoSwitch=HSUPA_UU_ADCTRL-1&HSUPA_PBR_MEAS-1&HSUPA_EDCH_RSEPS_MEAS
-1;
MOD UCELLCAC: CellId=11, MaxUlTxPowerforConv=24, MaxUlTxPowerforInt=24,
MaxHsupaUserNum=20;
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061203 HSUPA Power Control.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
The features WRFD-010612 HSUPA Introduction Package must be configured before
this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature increases the system power efficiency, reduces the uplink and downlink
interference, and improves the system capacity by controlling the power on HSUPA physical
channels.
Procedure
l Activation Procedure
1. Run the NodeB MML command SET MACEPARA (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Radio Layer > Locell Algorithm
Parameters > MAC Parameters > MACEPARA; CME batch modification center:
3.17 Modifying Physical NodeB Parameters in Batches). In this step, set E-AGCH
HPC Parameters, E-RGCH HPC Parameters for Service Radio Links Set, and
E-HICH HPC Parameters for Service Radio Links Set to YES.
2. Run the NodeB MML command SET MACEPARA (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Radio Layer > Locell Algorithm
Parameters > MAC Parameters > MACEPARA; CME batch modification center:
3.17 Modifying Physical NodeB Parameters in Batches). In this step, set E-AGCH
HPC Mode, E-RGCH HPC Mode for Service Radio Links Set, and E-HICH HPC
Mode for Service Radio Links Set to FOLLOW_TPC.
3. Run the NodeB MML command SET MACEPARA (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Radio Layer > Locell Algorithm
Parameters > MAC Parameters > MACEPARA; CME batch modification center:
3.17 Modifying Physical NodeB Parameters in Batches). In this step, set E-AGCH
Power Offset(0.25dB), E-RGCH Power Offset for Service Radio Links Set
(0.25dB), E-HICH Power Offset for Service Radio Links Set(0.25dB), and E-
HICH Power Offset for Single Radio Link(0.25dB) to appropriate values according
to the network plan.
4. Run the BSC6900 MML command MOD UTYPRABHSUPAPC (CME single
configuration: UMTS Radio Global Configuration Express > Typical Service
Configuration > Typical RAB HSUPA Power Control Parameters; CME batch
modification center: not supported) to modify power control parameters related to
HSUPA services. In this step, set E-RGCH 2-Index-Step Threshold to 9 and E-
RGCH 3-Index-Step Threshold to 12.
5. Run the BSC6900 MML command MOD UTYPRABOLPC (CME single
configuration: UMTS Radio Global Configuration Express > Typical Service
Configuration > Typical RAB OLPC Parameters; CME batch modification center:
not supported). In this step, change the number of target retransmissions for large and
small retransmissions related to HSUPA services according to the network plan.
l Verification Procedure
1. On the BSC6900 LMT, open the Monitor page. Then, double-click Connection
Performance Monitoring under UMTS Monitoring. In the displayed dialog box,
select OLPC and specify the IMSI.
2. Use an HSUPA-capable UE to set up a PS service over the enhanced DCH (E-DCH).
3. Move the UE between the cell center and the cell edge.
4. View the monitor items related to the number of E-DCH retransmissions in the
OLPC area. The values of the monitor items change with UE movement.
5. View the power change on each HSUPA channel.
If static power control is used, the channel power remains unchanged.
If dynamic power control is used:
When the UE is moving away from the antenna, the transmit power of the E-
AGCH increases.
When the UE is moving towards the antenna, the transmit power of the E-
AGCH decreases.
l Deactivation Procedure
1. This feature does not need to be deactivated.
----End
Example
//Activating HSUPA Power Control
//Setting the power control mode
SET MACEPARA: LOCELL=111, EAGCHPCPARA=YES, SERGCHPCPARA=YES,
SEHICHPCPARA=YES;
SET MACEPARA: LOCELL=111, EAGCHPCMOD=FOLLOW_TPC, SERGCHPCMOD=FOLLOW_TPC,
SEHICHPCMOD=FOLLOW_TPC;
SET MACEPARA: LOCELL=111, EAGCHPWROFFSET=142, SERGCHPWROFFSET=100,
SEHICHPWROFFSET=96, SRLEHICHPWROFFSET=88;
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061204 HSUPA Mobility Management.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The feature WRFD-010612 HSUPA Introduction Package must be configured before
this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature enables an HSUPA-capable UE to be handed over to an R99 cell or another HSUPA
cell.
This feature also enables an HSUPA-capable UE to change cells with a small probability of
service interruption.
Procedure
l Activation Procedure
1. The methods of activating intra-frequency, inter-frequency, and inter-RAT handovers
are the same for HSUPA users and R99 users. For the activation procedures for
configuring HSUPA Mobility Management, see the following sections:
35 Configuring Intra Frequency Hard Handover
236 Configuring Inter Frequency Hard Handover Based on Coverage
237 Configuring Inter Frequency Hard Handover Based on DL QoS
247 Configuring Inter Frequency Load Balance
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061208 HSUPA DCCC.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
The features WRFD-010612 HSUPA Introduction Package must be configured before
this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
HSUPA DCCC can dynamically adjust the minimum spreading factor (SF) code of HSUPA
based on the user throughput and flexibly switch the UE state based on the user traffic, which
improves the Channel Element (CE) resource utilization and system efficiency.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, select DRA_HSUPA_DCCC_SWITCH from
the Dynamic Resource Allocation Switch drop-down list.
2. Optional: If the NodeB does not enable dynamic CE, run the BSC6900 MML
command MOD UNODEBALGOPARA (CME single configuration: NodeB
Configuration Express > IUB_RNC > NodeB Basic Information > NodeB
Algorithm Parameters; CME batch modification center: 3.16 Modifying Logical
NodeB Parameters in Batches). In this step, set HSUPA Credit Consume Type to
MBR.
3. Optional: Run the BSC6900 MML command SET UDCCC (CME single
configuration: UMTS Radio Global Configuration Express > Dynamic Channel
Control Parameter Configuration > RNC Oriented DCCC Algorithm
Parameters; CME batch modification center: 3.15 Modifying RNC Parameters in
Batches). In this step, select RATE_UP_AND_DOWN_ON_EDCH from the
HSUPA DCCC Strategy drop-down list so that the data rate of HSUPA services on
the EDCH can increase or decrease.
NOTE
After the preceding optional step is performed, the data rate of HSUPA services on the EDCH can
increase or decrease as required. If the data rate of HSUPA services on the EDCH is expected to
increase only, select RATE_UP_ONLY_ON_EDCH from the HSUPA DCCC Strategy drop-
down list.
4. Optional: Run the BSC6900 MML command SET UEDCHRATEADJUSTSET
(CME single configuration: UMTS Radio Global Configuration Express >
Dynamic Channel Control Parameter Configuration > HSUPA Rate Adjust
Set; CME batch modification center: 3.15 Modifying RNC Parameters in
Batches). In this step, set HSUPA Uplink Rate Adjust Set to a data rate set for rate
adjustment by the HSUPA DCCC algorithm.
NOTE
The preceding optional step sets the available data rate set of the HSUPA DCCC algorithm. After
the step is performed, HSUPA services can be of any data rate in the data rate set by using the HSUPA
DCCC algorithm.
l Verification Procedure
1. On the BSC6900 LMT, display the Monitor page. In the Monitor Navigation
Tree, double-click UMTS Monitoring > Connection Performance Monitoring.
Select UL Throughput Bandwidth and DL Throughput Bandwidth respectively
from the Monitor Item drop-down list to create two monitoring tasks.
2. Make the UE establish an HSUPA Best Effort (BE) service. After the service is
established, layer 3 of the RNC sends an uplink throughput measurement control
message to layer 2.
3. Upload a large file for a period of time. Then, view the RRC_RB_RECFG message
on the Uu interface and check that the data rate increases. In UL Throughput
Bandwidth of Connection Performance Monitoring, the bandwidth increases.
4. Stop the data upload and wait for a period of time. Then, view the RRC_RB_RECFG
message on the Uu interface and check that the data rate decreases. In UL Throughput
Bandwidth of Connection Performance Monitoring, the bandwidth decreases.
l Deactivation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, deselect DRA_HSUPA_DCCC_SWITCH
from the Dynamic Resource Allocation Switch drop-down list.
----End
Example
//Activating HSUPA DCCC
SET UCORRMALGOSWITCH: DraSwitch=DRA_HSUPA_DCCC_SWITCH-1;
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061211 20 HSUPA Users per Cell.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
The feature WRFD-010612 HSUPA Introduction Package must be configured before
this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature enables a single HSUPA cell to serve a maximum of 20 HSUPA users
simultaneously. After the maximum is reached, the cell attempts to establish services on DCHs
to accommodate additional users.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command MOD UCELLALGOSWITCH (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Algorithm Switches; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches). In this step, deselect HSDPA_UU_ADCTRL(HSDPA UU
Load Admission Control Algorithm) and HSUPA_UU_ADCTRL(HSUPA UU
Load Admission Control Algorithm) from the drop-down list of Cell CAC
algorithm switch.
2. Run the BSC6900 MML command MOD UCELLCAC (CME single configuration:
UMTS Cell Configuration Express > Cell Parameters > Cell Oriented CAC
The 20 HSUPA users referred to in this feature are of the SRB Over HSPA type.
l Deactivation Procedure
1. This feature does not need to be deactivated.
----End
Example
/*Activation procedure*/
//Disabling the admission control function in an HSPA cell on the Uu
interface
MOD UCELLALGOSWITCH: CellId=111,
NBMCacAlgoSwitch=HSDPA_UU_ADCTRL-0&HSUPA_UU_ADCTRL-0;
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061212 HSUPA Iub Flow Control in Case of Iub Congestion.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The feature WRFD-010612 HSUPA Introduction Package has been configured before
this feature is activated.
l License
This feature is not under license control.
Context
By monitoring Iub transmission resources, this feature dynamically adjusts the uplink Uu
throughput and thereby greatly improves resource utilization.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET URRCTRLSWITCH (CME single
configuration: UMTS Radio Global Configuration Express > Process Switch
Configuration > Process Switch; CME batch modification center: 3.15 Modifying
RNC Parameters in Batches). In this step, select the
NODEB_PRIVATE_INTERFACE_SWITCH check box under the parameter
PROCESSSWITCH.
2. Run the BSC6900 MML command SET UDPUCFGDATA (CME single
configuration: UMTS Radio Global Configuration Express > DPU Data
Configuration > DPU Configuration Parameters; CME batch modification center:
3.15 Modifying RNC Parameters in Batches). In this step, set HsupaTnlSwitch to
ON(ON).
l Verification Procedure
NOTE
Example
//Activation procedure
SET URRCTRLSWITCH: PROCESSSWITCH=NODEB_PRIVATE_INTERFACE_SWITCH-1;
SET UDPUCFGDATA: HsupaTnlSwitch=ON;
//Deactivation procedure
SET UDPUCFGDATA: HsupaTnlSwitch=OFF;
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061401 HSUPA E-AGCH Power Control (Based on CQI or HS-SCCH).
Prerequisites
l Dependencies on Hardware
This feature does not depend on hardware.
l Dependencies on Other Features
The following features have been configured before this feature is activated:
WRFD-010610 HSDPA Introduction Package and WRFD-010612 HSUPA
Introduction Package.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature enables the RAN to use the channel quality indicator (CQI) and HS-SCCH
information reported by UEs as a reference, therefore effectively reducing the power
consumption of the E-AGCH.
Procedure
l Activation Procedure
1. Run the NodeB MML command SET MACEPARA (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Radio Layer > Locell Algorithm
Parameters > MAC Parameters > MACEPARA; CME batch modification center:
3.17 Modifying Physical NodeB Parameters in Batches) to set Mac-e parameters
with the following parameter settings:
E-AGCH HPC Parameters is set to YES(YES).
E-AGCH HPC Mode is set to CQI_BASED(Tx Pwr Ctr based on CQI) or
HSSCCH_BASED(Tx Pwr Ctr based on HS-SCCH).
Example
//Activation procedure
SET MACEPARA: SCHEDULEPARA=NO, EAGCHPCPARA=YES, EAGCHPCMOD=CQI_BASED,
EAGCHPWROFFSET=100, MAXAGCHPOWER=100,
MINAGCHPOWER=-200, SERGCHPCPARA=NO, NSERGCHPCPARA=NO, SEHICHPCPARA=NO,
NSEHICHPCPARA=NO;
//Deactivation procedure
SET MACEPARA: SCHEDULEPARA=NO, EAGCHPCPARA=NO, SERGCHPCPARA=NO,
NSERGCHPCPARA=NO, SEHICHPCPARA=NO, NSEHICHPCPARA=NO;
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061403 HSUPA 2ms TTI.
Prerequisites
l Dependencies on Hardware
Dependencies on BSC6900 Hardware
This feature does not depend on the BSC6900 hardware.
Dependencies on NodeB Hardware
The BTS3812E, BTS3812A and BTS3812AE need to configure EBBI board, EBOI
board, EDLP or EDLPd board.
The BBU3806 is configured with the EBBC or EBBCd board.
The BBU3900 is configured with the WBBPb,WBBPd or WBBPf board.
l Dependencies on Other Features
The following features have been configured before this feature is activated:
WRFD-010612 HSUPA Introduction Package.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The UE should have the capability of HSUPA Category 2, 4, 6, 7, 8, 9.
Context
This feature enables a single user to obtain a higher uplink throughput and a shorter delay.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
l Deactivation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, deselect the
MAP_HSUPA_TTI_2MS_SWITCH check box under the parameter Service
Mapping Strategy Switch.
2. Optional: If the single-user peak-rate improvement algorithm of HSUPA 2 ms TTI
is to be deactivated, Run the BSC6900 MML command SET UCORRMPARA (CME
single configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > the connection-oriented
algorithm parameters of an RNC; CME batch modification center: 3.15 Modifying
RNC Parameters in Batches). In this step, deselect the
Example
//Activating HSUPA 2ms TTI
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061404 HSUPA 2 ms/10 ms TTI Handover.
Prerequisites
l Dependencies on Hardware
Dependencies on BSC6900 Hardware
This feature does not depend on the BSC6900 hardware.
Dependencies on NodeB Hardware
The BTS3812E, BTS3812A, or BTS3812AE is configured with the EBBI, EBOI,
EULP, or EULPd board.
The BBU3806 is configured with the EBBC or EBBCd board.
The BBU3900 is configured with the WBBPb ,WBBPd or WBBPf board.
l Dependencies on Other Features
The feature WRFD-010614 HSUPA Phase 2 has been configured before this feature is
activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature enables smooth handovers for HSUPA users between 2 ms TTI capable cells and
10 ms TTI capable cells, aiming to maximize HSUPA resource utilization. When this feature is
used, the factors such as the radio environment, CE resource usage, and user throughput rate are
considered.
This feature contains three functions: Dynamic TTI Adjustment for a Single Voice Service over
HSUPA, Differentiation-based Dynamic TTI Adjustment for a Single BE Service over HSUPA,
and Admission-CE-based Dynamic TTI Adjustment for a Single BE Service over HSUPA.
Procedure
l Activation Procedure
This feature is license controlled. It takes effect after its license is activated.
l Verification Procedure
This feature does not need to be verified.
l Deactivation Procedure
This feature does not need to be deactivated.
----End
Example
None
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061405 HSUPA 5.74Mbps per User.
Prerequisites
l Dependencies on Hardware
Dependencies on BSC6900 Hardware
This feature does not have any special requirements for hardware.
Dependencies on NodeB Hardware
The BTS3812E , BTS3812A, and BTS3812AE should be configured with the EBBI,
EBOI, EULP or EULPd board, the downlink services can only be set up on EBBI,
EBOI, EDLP.
For BBU3806, the downlink services can only be set up on EBBC or EBBCd board.
The BBU3900 should be configured with the WBBPb ,WBBPd or WBBPf board.
l Dependencies on Other Features
The feature WRFD-010636 SRB over HSUPA has been configured before this feature
is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
CN support the uplink speed of 5.74 Mbit/s (or more) .
The UE is of HSUPA category 6, 7, 8, or 9.
Context
This feature enables the HSUPA rate at the MAC layer to reach a maximum of 5.74 Mbit/s.
Procedure
l Activation Procedure
1. Optional: Run the BSC6900 MML command MOD TRMMAP (CME single
configuration: UMTS Global Configuration Express > Transmission Resources
Configuration > Transport Resource Mapping; CME batch modification center:
not supported) to configure the TRM mapping table based on the network plan. The
TRM mapping table contains the mapping relationship between the transmission mode
and the service type.
NOTE
The BSC6900 provides a default TRM mapping table. Use an appropriate mapping policy when
configuring the TRM mapping table. For example, if Transport Type is set to ATM, all HSUPA
services, including signaling services, must be carried by AAL2PATH that supports HSUPA
services.
2. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to enable HSUPA services to use the 2 ms TTI. In this step,
set Service Mapping Strategy Switch to MAP_HSUPA_TTI_2MS_SWITCH.
3. Run the BSC6900 MML command SET UFRCCHLTYPEPARA (CME single
configuration: UMTS Radio Global Configuration Express > Basic Resource
Control Parameter Configuration > Channel Type Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches) to enable SRBs
to be carried on HSUPA channels. In this step, set Type of Channel Preferably
Carrying Signaling RB to HSUPA(UL_EDCH,DL_DCH).
l Verification Procedure
1. Use an HSPA-capable UE to establish a PS service on the E-DCH and HS-DSCH.
2. Start Uu interface tracing on the BSC6900 LMT. The RRC_RB_SETUP message
shows that the 2 ms TTI is used in the uplink and the maximum channelization code
IE is 2SF2+2SF4.
3. The real-time monitoring result of UL Throughput & Bandwidth on the BSC6900
side shows that the bandwidth is 5440 kbit/s and that upload through FTP is normal.
l Deactivation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to prohibit the 2 ms TTI from being used on HSUPA
channels. In this step, deselect the MAP_HSUPA_TTI_2MS_SWITCH check box
under the Service Mapping Strategy Switch parameter.
2. Run the BSC6900 MML command SET UFRCCHLTYPEPARA (CME single
configuration: UMTS Radio Global Configuration Express > Basic Resource
Control Parameter Configuration > Channel Type Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches) to prohibit SRBs
from being carried on HSPA channels. In this step, set Type of Channel Preferably
Carrying Signaling RB to DCH(UL_DCH,DL_DCH).
----End
Example
//Activating HSUPA 5.74Mbps per User
SET UCORRMALGOSWITCH: MapSwitch=MAP_HSUPA_TTI_2MS_SWITCH-1;
SET UFRCCHLTYPEPARA: SrbChlType=HSUPA;
//Deactivating HSUPA 5.74Mbps per User
SET UCORRMALGOSWITCH: MapSwitch=MAP_HSUPA_TTI_2MS_SWITCH-0;
SET UFRCCHLTYPEPARA: SrbChlType=DCH;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010632
Streaming Traffic Class on HSUPA.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The feature WRFD-010612 HSUPA Introduction Package has been configured before
this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature allows PS streaming services to be carried on E-DCHs, thereby increasing the
utilization of cell resources.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, select the
MAP_PS_STREAM_ON_HSUPA_SWITCH check box under the parameter
Service Mapping Strategy Switch.
2. Run the BSC6900 MML command SET UFRCCHLTYPEPARA (CME single
configuration: UMTS Radio Global Configuration Express > Basic Resource
Control Parameter Configuration > Channel Type Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches). In this step, set
Example
//Activating Streaming Traffic Class on HSUPA
SET UCORRMALGOSWITCH: MapSwitch=MAP_PS_STREAM_ON_HSUPA_SWITCH-1;
SET UFRCCHLTYPEPARA: UlStrThsOnHsupa=D256;
//Deactivating Streaming Traffic Class on HSUPA
SET UCORRMALGOSWITCH: MapSwitch=MAP_PS_STREAM_ON_HSUPA_SWITCH-0;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010635
HSUPA over Iur.
Prerequisites
l Dependencies on Hardware
The neighboring RNC supports this feature.
l Dependencies on Other Features
The feature WRFD-010612 HSUPA Introduction Package has been configured before
this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The neighboring RNC must support HSUPA over Iur too.
Context
This feature enables HSUPA services to be carried on the Iur interface so that continuous HSUPA
services can be provided for UEs moving between BSC6900s.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command MOD UEXT3GCELL (CME single
configuration: Object Group > UMTS Service Configuration and Maintenance
Management > External Cell Configuration > RNC 3G External Cell; CME batch
modification center: 3.19 Modifying RNC External Cell Parameters in Batches)
to configure a neighboring RNC's cell with the E-DCH function. In this step, set Cell
Capability Container to an appropriate value.
2. Run the BSC6900 MML command MOD UNRNC (CME single configuration: IUR
Configuration Express > Neighbouring RNC > Neighboring RNC; CME batch
modification center: not supported) to configure data about the neighboring RNC. In
this step, set Hsupa cap ind over IUR for NRNC to ON to enable HSUPA services
to be carried on the Iur interface.
l Verification Procedure
1. Verify that the feature HSUPA over Iur has been activated by performing the following
operations:
Run the BSC6900 MML command LST UNRNC to query the configuration of
the neighboring RNC.
Run the BSC6900 MML command LST UEXT3GCELL to query the
configuration of the neighboring RNC's cell.
2. Verify that an HSUPA service has been established on the Iur interface by performing
the following operations:
Configure the neighboring RNC and its cell with the HSUPA function.
Establish an HSUPA service under the serving RNC.
Add a cross-Iur soft handover link.
If the RNSAP_RL_SETUP_REQ message traced on the Iur interface contains
HSUPA-related information elements, an HSUPA service has been set up
successfully.
l Deactivation Procedure
1. Run the BSC6900 MML command MOD UNRNC (CME single configuration: IUR
Configuration Express > Neighbouring RNC > Neighboring RNC; CME batch
modification center: not supported). In this step, set Hsupa cap ind over IUR for
NRNC to OFF.
----End
Example
//Activation procedure
MOD UEXT3GCELL: NRncId=2, CellId=2,
CellCapContainerFdd=EDCH_SUPPORT-1&EDCH_2SF4_SUPPORT-1&EDCH_HARQ_IR_COMBI
N_SUPPORT-1;
MOD UNRNC: NRncId=2,
SHOTRIG=CS_SHO_SWITCH-1&HSPA_SHO_SWITCH-1&NON_HSPA_SHO_SWITCH-1,
ServiceInd=SUPPORT_CS_AND_PS, IurExistInd=TRUE, TnlBearerType=IP_TRANS,
Dpx=2, IurHsupaSuppInd=ON;
//Deactivation procedure
MOD UNRNC: NRncId=1, IurHsupaSuppInd=OFF;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010690
TTI Switch for BE Services Based on Coverage.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The feature WRFD-010614 HSUPA Phase 2 has been configured before this feature is
activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature dynamically adjusts transmission time intervals (TTIs) based on UE transmit power
and uplink service throughput. The TTI of UEs in the cell center is switched to 2 ms to increase
the service rate, whereas the TTI of UEs at the cell edge is switched to 10 ms to expand the
coverage.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to turn on the switch for this feature. In this step, select the
DRA_DCCC_SWITCH and the
DRA_BASE_COVER_BE_TTI_RECFG_SWITCH check box under the
parameter Dynamic Resource Allocation Switch.
2. Optional: If the Uplink Enhanced L2 feature is used, run the BSC6900 MML
command SET UCORRMALGOSWITCH (CME single configuration: UMTS
Radio Global Configuration Express > Connection_Oriented RRM Switch
Configuration > Connection Oriented Algorithm Switches; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches). In this step,
select the DRA_BASE_COVER_BE_TTI_L2_OPT_SWITCH check box under
the parameter Dynamic Resource Allocation Switch.
NOTE
2. Adjust the distance between the UE and the NodeB to trigger a switching of the TTI
from 2 ms to 10 ms.
3. Analyze the traced messages shown in Figure 110-2 and Figure 110-3. The TTI has
switched from 2 ms to 10 ms.
l Deactivation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to turn off the switch for this feature. In this step, deselect
the DRA_BASE_COVER_BE_TTI_RECFG_SWITCH check box under the
parameter Dynamic Resource Allocation Switch.
----End
Example
//Activating TTI Switch for BE Services Based on Coverage
//Turning on the switch for the feature TTI Switch for BE Services Based
on Coverage
SET UCORRMALGOSWITCH:
DraSwitch=DRA_HSUPA_DCCC_SWITCH-1&DRA_BASE_COVER_BE_TTI_INIT_SEL_SWITCH-1
;
//Turning on the switch for TTI L2+ for BE services based on coverage
SET UCORRMALGOSWITCH: DraSwitch=DRA_BASE_COVER_BE_TTI_L2_OPT_SWITCH-1;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010641
HSUPA Adaptive Transmission.
Prerequisites
l Dependencies on Hardware
Dependencies on BSC6900 Hardware
This feature does not have any special requirements for hardware.
Dependencies on NodeB Hardware
The BTS3812E and BTS3812AE should be configured with the EBBI, EBOI, EULP
or EULPd board.
The BBU3806 is configured with the EBBC or EBBCd board.
The BBU3900 is configured with the WBBPb, WBBPd or WBBPf board.
l Dependencies on Other Features
The feature WRFD-010612 HSUPA Introduction Package must be configured before
this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
Considering cell uplink power load, CE resources, and limited uplink coverage, this feature
enables the BTS to adjust the target number of uplink retransmissions to increase the throughput
per user and cell uplink capacity.
Procedure
l Activation Procedure
1. To enable the message containing NodeB private interface data to be transmitted to
the NodeB over the Iub interface, run the BSC6900 MML command SET
l Deactivation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, deselect
PC_HSUPA_HARQNUM_AUTO_ADJUST_SWITCH from the Power Control
Switch drop-down list to deactivate HSUPA Adaptive Transmission.
2. Run the NodeB MML command SET ADPRETRANSSWTCH (CME single
configuration: NodeB Configuration Express > IUB_NodeB > Basic
Information > Radio Management > ADPRETRANSSWTCH; CME batch
modification center: not supported) to deactivate HSUPA Adaptive Transmission on
the NodeB side.
----End
Example
//Activating HSUPA Adaptive Transmission (BSC6900 MML command)
SET URRCTRLSWITCH: PROCESSSWITCH=NODEB_PRIVATE_INTERFACE_SWITCH-1;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010638
Dynamic CE Resource Management.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
WRFD-010612 HSUPA Introduction Package
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
To improve utilization efficiency of channel element (CE) resources, Huawei RAN introduces
the Dynamic CE Resource Management feature. This feature helps to quickly adjust CE
allocation by considering the Guaranteed Bit Rate (GBR) and the actual rate of a UE. During
preemption of CE resources, this feature is used to allocate CE resources in a reasonable way,
therefore ensuring preemption fairness.
Procedure
l Activation Procedure
1. The feature does not need to be activated.
l Verification Procedure
1. Start Tracing Messages on the Iub Interface on BSC6900 LMT and check whether the
value of dynamic-CE-Switch-Private in NBAP_AUDIT_RSP is 1.
If the value is 1, it indicates the feature is activated. Else, it indicates the feature is not
activated. When the value of dynamic-CE-Switch-Private is 1, see Figure 112-1.
l Deactivation Procedure
1. Set NodeB license control item the number of NodeBs with dynamic CE function
enabled to 0 on M2000 client . Details see Allocating a License to NodeBs.
----End
Example
None
This section describes how to activate, verify, and deactivate the optional feature WRFD-010692
HSUPA FDE.
Prerequisites
l Dependencies on Hardware
Dependencies on BSC6900 Hardware
This feature does not have any special requirements for hardware.
Dependencies on NodeB Hardware
The BTS3812E/BTS3812AE must be configured with the EULPd board.
The DBS3800 must be configured with the EBBCd board.
The 3900 series base stations must be configured with the WBBPd or WBBPf board.
l Dependencies on Other Features
WRFD-010612 HSUPA Introduction Package.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
HSUPA FDE equalizes the spectrum in the frequency domain on the HSUPA E-DPDCH through
the UL receiver of the NodeB, therefore suppressing the inter-path interference on the E-
DPDCH. In this manner, the SNR on the EDPDCH is increased and the UL system capacity of
the HSUPA network is expanded. The rate of HSUPA services is also increased in multipath
environment.
NOTE
For UEs of category 6 and category 7 at a transmission rate higher than 2 Mbit/s, the feature brings notable
gains if multipath channels are used in the uplink.
Procedure
l Activation Procedure
1. Run the NodeB MML command MOD LOCELL (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Radio Layer > xx Sector > Locell; CME
batch modification center: 3.17 Modifying Physical NodeB Parameters in
Batches) to modify the local cell. In this step, set FDE to TRUE.
l Verification Procedure
1. Run the NodeB MML command DSP LOCELL to query the configuration
information about the local cell.
Expected result: The value of FDE MODE is ENABLED.
l Deactivation Procedure
1. Run the NodeB MML command MOD LOCELL (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Radio Layer > xx Sector > Locell; CME
batch modification center: 3.17 Modifying Physical NodeB Parameters in
Batches) to modify the local cell. In this step, set FDE to FALSE.
----End
Example
//Activation procedure
MOD LOCELL: LOCELL=1, SECT=LOCAL_SECTOR, FDE_MODE=TRUE;
//Verification procedure
DSP LOCELL: LOCELL=1;
//Deactivation procedure
MOD LOCELL: LOCELL=1, SECT=LOCAL_SECTOR, FDE_MODE=FALSE;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010712
Adaptive Configuration of Traffic Channel Power offset for HSUPA.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The feature WRFD-010612 HSUPA Introduction Package has been configured before
this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
As the HSPA/HSPA+ becomes an increasingly popular mainstream technology, uplink system
performance needs to be enhanced to adapt to the ever-refreshed HSUPA peak rate. Based on
the changes in subscriber behaviors and network status, this feature adaptively configures the
parameters related to power control on the optimum uplink data channel, increasing the HSUPA
system capacity.
NOTE
l This feature applies only to HSUPA Best Effort (BE) services whose Transmission Timing Interval (TTI)
is 10 ms.
l This feature is applicable to the scenarios where dynamic channel configuration control (DCCC) takes effect
and the scenarios where dynamic channel element (CE) takes effect (DCCC does not take effect).
l This feature is highly dependent on parameter settings. The relevant parameters must retain the default
values. This feature may fail to take effect if these parameter settings are changed.
Procedure
l Activation Procedure
CAUTION
Before activating this feature, check the settings of the following two parameters: if
Reference E-TFCI Index1 is set to 4 and Reference E-TFCI Power Offset1 is set to
12, you are advised to set Reference E-TFCI Power Offset1 to 8.
NOTE
l In dynamic CE scenarios, the service rate assigned by the core network (CN) is 2048 kbit/s, and the
BSC6900 configures the Hybrid Automatic Repeat Request (HARQ) power offset (PO) based on the
realtime service rate. In the scenarios where DCCC takes effect, the actual service rate is variable, and
the BSC6900 configures the HARQ PO based on the realtime service rate.
l The HARQ PO is one of the variable that determines the power offset on the E-DPDCH compared
with the DPCCH.
1. Run the BSC6900 MML command LST UTYPRABHSUPAPC to check the
parameters related to power offset for typical services. Figure 114-1 shows an
interactive BE service with the CN-assigned rate of 2048 kbit/s, whose Service
parameter index is set to 55, Traffic Subflow Index to 0, Transport channel
type to TRCH_EDCH_10MS, and the Ul 16QAM Used Indication, Ul enhanced
L2 Used Indication, EdPower Interpolation Priority Used Indication, and UL E-
DPCCH Boosting Indication parameters all set to FALSE. As shown in Figure
114-1, HARQ PO for Large Retransmission is set to 0, HARQ PO for small
Retrans at Low Speed is set to 4, and HARQ PO for small Retrans at High
Speed is set to 0.
2. Establish a PS interactive BE service over HSUPA, for example, upload files to the
FTP server.
NOTE
l In multi-user scenarios where the target load is limited and the realtime service rate of a single
user is lower than a low-rate threshold (such as 150 kbit/s), the user is in the small retransmission
state at a low speed. The HARQ PO is the value of HARQ PO for small Retrans at Low
Speed.
l If the realtime service rate of a single user is higher than a high-rate threshold (such as 300 kbit/
s), the user is in the small retransmission state at a high speed. The HARQ PO is the value of
HARQ PO for small Retrans at High Speed.
3. Check the realtime rate of the new BE service and the CN-assigned rate by referring
to Monitoring UL Throughput and Bandwidth, as shown in Figure 114-2.
Figure 114-3 HARQ PO (4) of a UE for small retransmission at a low speed (256
kbit/s)
b. After the file upload on the FTP is complete, check the uplink data rate of the
UE by referring to Monitoring UL Throughput and Bandwidth. When the
data rate is 608 kbit/s, check the value of HARQ PO in the
RRC_RB_RECFG message by referring to Tracing Messages on the Uu
Interface. The HARQ PO changes from HARQ PO for small Retrans at High
Speed for 256 kbit/s to that for 608 kbit/s, as shown in Figure 114-4.
shows that the user is in the small retransmission state at a high speed when
accessing the network. The HARQ PO is equal to the value of HARQ PO for
small Retrans at High Speed, as shown in Figure 114-5.
b. Simulate a situation that the uplink load is limited by changing the target uplink
load to 10%. Run the BSC6900 MML command MOD UCELLHSUPA. In this
step, set Maximum Target Uplink Load Factor to 10. After the uplink load is
limited, check the uplink throughput and bandwidth by referring to Monitoring
UL Throughput and Bandwidth. HARQ PO reconfiguration is triggered when
the uplink throughput of the UE is lower than the low-rate threshold. Check the
value of HARQ PO in the RRC_RB_RECFG message by referring to Tracing
Messages on the Uu Interface. The HARQ PO changes from HARQ PO for
small Retrans at High Speed to HARQ PO for small Retrans at Low
Speed, as shown in Figure 114-6.
l Deactivation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to turn off the switch for this feature. In this step, clear the
PC_HSUPA_DATA_CH_PO_ADAPTIVE_ADJ_SWITCH check box under the
parameter Power Control Switch.
----End
Example
//Activation procedure in the scenario where DCCC takes effect
SET UCORRMALGOSWITCH: PcSwitch=PC_HSUPA_DATA_CH_PO_ADAPTIVE_ADJ_SWITCH-1;
SET UCORRMALGOSWITCH:
DraSwitch=DRA_DCCC_SWITCH-1&DRA_HSUPA_DCCC_SWITCH-1;
SET UEDCHRATEADJUSTSET:
EdchRateAdjustSet=RATE_128KBPS-1&RATE_256KBPS-1&RATE_608KBPS-1&RATE_2048K
BPS-1;
SET UFRC: HsupaInitialRate=D256;
//Verification procedure
LST UTYPRABHSUPAPC: QueryType=QUERY_BY_PROPERTY, CNDomainId=PS_DOMAIN,
TrafficClass=INTERACTIVE, MaxBitRate=256000, TrchType=TRCH_EDCH_10MS,
Ul16QamInd=FALSE, UlL2EnhanceInd=FALSE, EdPwrInterpolationInd=FALSE,
UlEcBoostingInd=FALSE;
//Deactivation procedure
SET UCORRMALGOSWITCH: PcSwitch=PC_HSUPA_DATA_CH_PO_ADAPTIVE_ADJ_SWITCH-0;
This section describes how to activate, verify, and deactivate the optional feature WRFD-020136
Anti-Interference Scheduling for HSUPA.
Prerequisites
l Dependencies on Hardware
Dependencies on BSC6900 Hardware
This feature does not have any special requirements for hardware.
Dependencies on NodeB Hardware
The BTS3812E and BTS3812AE should be configured with the HBBI, EBBI,
HULP, EBOI, EULP, or EULPd board. The downlink services can only be set up
on the EBBI, EBOI, or EDLP board.
The BBU3806 is configured with the EBBC or EBBCd board.
The BBU3900 is configured with the WBBPb, WBBPd or WBBPf board.
l Dependencies on Other Features
WRFD-010612 HSUPA Introduction Package
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
In commercial networks, the uplink data transmission of HSUPA at some sites is affected
randomly by strong external interference. When a site is strongly interfered, the HSUPA
throughput of the site is significantly reduced and user experience is affected.
This feature can eliminate the strong external interference and maintain high HSUPA
throughput, improving user experience.
NOTE
This feature is not proposed for multi-RRU cells.
Procedure
l Activation Procedure
1. Run the NodeB MML command SET MACEPARA (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Radio Layer > Locell Algorithm
Parameters > MAC Parameters > MACEPARA; CME batch modification center:
3.17 Modifying Physical NodeB Parameters in Batches) to set Mac-e parameters.
a. Set the MAC-e Schedule Para to YES(YES).
b. Set the Anti-Interference Scheduling Switch to ON(ON).
c. Own Cell UL Load Ratio.
In indoor coverage scenarios, the recommended value is 90.
In non-indoor coverage scenarios, the recommended value is 60.
d. It is recommended that Min UL Cover Load Threshold(dB) be set to 13.
NOTE
If Local Cell ID is not specified, the Mac-e scheduling parameters of all local cells under the
NodeB will be set.
CAUTION
If the following conditions are met, step 2 is not required, and the configuration ends.
l On the RNC side, UL_UU_OLC(Uplink UU OLC Algorithm) is not selected
for Switch for Cell Load Control.
l On the RNC side, ALGORITHM_OFF or ALGORITHM_SECOND is selected
for Uplink CAC algorithm switch.
6. Run the NodeB MML command SET MACEPARA to set Mac-e parameters.
a. Set the Anti-Interference Scheduling Switch to ON(ON).
b. Own Cell UL Load Ratio
In indoor coverage scenarios, the recommended value is 90.
In non-indoor coverage scenarios, the recommended value is 60.
c. It is recommended that Min UL Cover Load Threshold(dB) be set to 13.
NOTE
If Local Cell ID is not specified, the Mac-e scheduling parameters of all local cells under the
NodeB will be set.
7. Select Service > Realtime Specific Monitoring > Cell RTWP from the navigation
tree in Maintenance tab on NodeB LMT, as shown in Figure 115-1. The column
1-3 indicates the state of this feature enabled. If the values of column 1-3 in Figure
115-1 are bigger than the values of 1-3 in Figure 115-2, it indicates the feature has
been enabled.
l Deactivation Procedure
1. Run the NodeB MML command SET MACEPARA (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Radio Layer > Locell Algorithm
Parameters > MAC Parameters > MACEPARA; CME batch modification center:
3.17 Modifying Physical NodeB Parameters in Batches) to set Mac-e parameters.
Set the MAC-e Schedule Para to YES(YES).
Set the Anti-Interference Scheduling Switch to OFF(OFF).
----End
Example
//Activation procedure
SET MACEPARA: LOCELL=0, SCHEDULEPARA=YES, OUTERSYSINTERSCHSW=ON,
OWNCELLULLOADRATIO=60, LOADTHRESH4MINULCOV=13, EAGCHPCPARA=NO,
SERGCHPCPARA=NO, NSERGCHPCPARA=NO, SEHICHPCPARA=NO, NSEHICHPCPARA=NO;
(Optional)MOD UCELLALGOSWITCH: CELLID=0,
NBMCacAlgoSwitch=RTWP_RESIST_DISTURB-1;
//Verification procedure
DSP LICENSE:;
SET MACEPARA: LOCELL=0, SCHEDULEPARA=YES, OUTERSYSINTERSCHSW=OFF,
EAGCHPCPARA=NO, SERGCHPCPARA=NO, NSERGCHPCPARA=NO, SEHICHPCPARA=NO,
NSEHICHPCPARA=NO;
SET DESENS: LOCELL=0, DI=6;
SET MACEPARA: LOCELL=0, SCHEDULEPARA=YES, OUTERSYSINTERSCHSW=ON,
OWNCELLULLOADRATIO=60, EAGCHPCPARA=NO, SERGCHPCPARA=NO, NSERGCHPCPARA=NO,
SEHICHPCPARA=NO, NSEHICHPCPARA=NO;
//Deactivation procedure
SET MACEPARA: LOCELL=0, SCHEDULEPARA=YES, OUTERSYSINTERSCHSW=OFF,
EAGCHPCPARA=NO, SERGCHPCPARA=NO, NSERGCHPCPARA=NO, SEHICHPCPARA=NO,
NSEHICHPCPARA=NO;
This section describes how to activate, verify, and deactivate the optional feature WRFD-020137
Dual-Threshold Scheduling with HSUPA Interference Cancellation.
Prerequisites
l Dependencies on BSC6900 Hardware
This feature does not have any special requirements for hardware.
l Dependencies on NodeB Hardware
The BTS3812E/AE must be configured with EULPd baord, and all users of the cell
should be estabilished in one EULPd board.
The DBS3800 must be configured with the EBBCd board.
The 3900 series base stations must be configured with the WBBPd board in the UL
resource pool which support IC feature, and slot 2 or 3 needs to be configured with at
least one WBBPd board.
The RRU3801C 20W and the MTFU for the BTS3812E and BTS3812AE do not support
this feature.
l Dependencies on Other Features
WRFD-010612 HSUPA Introduction Package
WRFD-010691 HSUPA UL Interference Cancellation
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature is applicable in cells enabled with the WRFD-010691 HSUPA UL Interference
Cancellation feature.
Procedure
l Activation Procedure
1. Run the NodeB MML command SET MACEPARA (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Radio Layer > Locell Algorithm
Parameters > MAC Parameters > MACEPARA; CME batch modification center:
3.17 Modifying Physical NodeB Parameters in Batches) to set Mac-e parameters.
Set the MAC-e Schedule Para to YES.
Set the Max Target RoT Difference Before and After IC to 2.
2. Run the BSC6900 MML commandMOD UCELLCAC (CME single configuration:
UMTS Cell Configuration Express > Cell Parameters > Cell Oriented CAC
Algorithm Parameters; CME batch modification center: 3.18 Modifying UMTS
Cell Parameters in Batches), set UL IC LDC Optimized Switch in the specified
cell to ON(ON).
l Verification Procedure
1. Run the NodeB MML command SET MACEPARA to set Mac-e parameters. Set
Max Target RoT Difference Before and After IC to 0.
2. Use multi users to carry out upload service.
3. Select Service > Realtime Specific Monitoring > Cell RTWP from the navigation
tree in Maintenance tab on NodeB LMT, as shown in Figure 116-1. The column
1-3 indicates the state of this feature disabled, the column 1-4 indicates the state of
this feature enabled. If the value of column 1-4 is less than the value of column 1-3,
it indicates HSUPA UL Interference Cancellation feature has been enabled.
4. Run the NodeB MML command SET MACEPARA to set Mac-e parameters. Set
Max Target RoT Difference Before and After IC to 2.
5. Check the Cell RTWP window. If the value of column 1-4 is less than the value of
column 1-3, and the values of column 1-4 and column 1-3 increase by 10, it indicates
dual-threshold scheduling with HSUPA interference cancellation feature has been
enabled.
NOTE
The prerequisite of the foregoing result is the cell power limit does not over.
----End
Example
//Activation procedure
//Operations at the NodeB
SET MACEPARA: LOCELL=0, SCHEDULEPARA=YES, MAXDELTAOFTARGETROT=2,
EAGCHPCPARA=NO, SERGCHPCPARA=NO,
NSERGCHPCPARA=NO, SEHICHPCPARA=NO, NSEHICHPCPARA=NO;
//Operations at the RNC
MOD UCELLCAC: CellId=1, UlIcLdcOptSwitch=ON;
//Verification procedure
//Operations at the NodeB
SET MACEPARA: LOCELL=0, SCHEDULEPARA=YES, MAXDELTAOFTARGETROT=0,
EAGCHPCPARA=NO, SERGCHPCPARA=NO,
NSERGCHPCPARA=NO, SEHICHPCPARA=NO, NSEHICHPCPARA=NO;
SET MACEPARA: LOCELL=0, SCHEDULEPARA=YES, MAXDELTAOFTARGETROT=2,
EAGCHPCPARA=NO, SERGCHPCPARA=NO,
NSERGCHPCPARA=NO, SEHICHPCPARA=NO, NSEHICHPCPARA=NO;
//Operations at the RNC
LST UCELLCAC: CellId=1;
//Deactivation procedure
//Operations at the NodeB
SET MACEPARA: LOCELL=0, SCHEDULEPARA=YES, MAXDELTAOFTARGETROT=0,
EAGCHPCPARA=NO, SERGCHPCPARA=NO,
NSERGCHPCPARA=NO, SEHICHPCPARA=NO, NSEHICHPCPARA=NO;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010634
60 HSUPA Users per Cell.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
The following features must be configured before this feature is activated:
WRFD-010612 HSUPA Introduction Package.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature enables a single HSUPA cell to serve a maximum of 60 HSUPA users
simultaneously. After the maximum number of users is reached, the cell attempts to establish
services on DCHs to accommodate additional users.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command MOD UCELLHSUPA (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters >
Configuration of HSUPA in Cell; CME batch modification center: 3.18 Modifying
UMTS Cell Parameters in Batches) to set Code Number for E-RGCH/E-HICH
to appropriate value.
2. Run the BSC6900 MML command MOD UCELLCAC (CME single configuration:
UMTS Cell Configuration Express > Cell Parameters > Cell Oriented CAC
Algorithm Parameters; CME batch modification center: 3.18 Modifying UMTS
Cell Parameters in Batches) to set Maximum HSUPA user number to 60.
l Verification Procedure
1. On the BSC6900 LMT, click Monitor. Then, double-click UMTS Monitoring > Cell
Performance Monitoring in the Monitor Navigation Tree pane. In the displayed
Cell Performance Monitoring dialog box, set Monitor Item to Cell User
Number.
2. Use UEs to access the cell one by one. Then, make UEs establish PS services, for
example, upload files through FTP.
Expected result: Each UE establishes PS services successfully.
If the number of UEs is less than or equal to 60, uplink services are carried on
HSUPA channels and downlink services are carried on HSDPA channels.
If the number of UEs is greater than 60, HSPA services of the excessive UEs are
carried on R99 channels.
3. View the maximum number of HSUPA users indicated by the counter
VS.HSUPA.UE.Max.Cell on the M2000.
NOTE
The 60 HSUPA users referred to in this feature are of the SRB Over HSPA type.
l Deactivation Procedure
1. This feature does not need to be deactivated.
----End
Example
/*Activation procedure*/
//Allocating code resources to E-RGCHs
MOD UCELLHSUPA: CellId=111, ErgchEhichCodeNum=3;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010691
HSUPA UL Interference Cancellation.
Prerequisites
l Dependencies on Hardware
Dependencies on BSC6900 Hardware
This feature does not have any special requirements for hardware.
Dependencies on NodeB Hardware
The BTS3812E or BTS3812AE must be configured with the EULPd board, the
downlink service cannot be estabilished on HBBI/HDLP/NDLP, and the IC effect
cannot be shared between BB boards.
The DBS3800 must be configured with the EBBCd board and the IC effect can be
shared between the BB boards.
The 3900 series base stations must be configured with the WBBPd or WBBPf board,
and only if slot 2 or 3 is configured with at least one WBBPd or WBBPf board, IC
effect can be shared between the WBBPd or WBBPf boards.
WBBPd/WBBPf is needed for 3900 series NodeB to support HSUPA UL
Interference Cancellation. If the inter-board sharing IC need to be supported, the
WBBPd/WBBPf should be configured in the UL resource pool which used for inter-
board sharing IC, and at least 1 WBBPd/WBBPf should be configured in slot 2 or
3.
l Dependencies on Other Features
WRFD-010612 HSUPA Introduction Package.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
CAUTION
Activate this feature when the traffic volume in a cell is low. The reason is that the cell must be
deactivated before this feature is activated; after the cell is deactivated, the services in this cell
are disrupted.
Interference Cancellation (IC) is performed to cancel the interference caused by the uplink high
rate E-DPDCH data of other users, improving the demodulation signal-to-noise ratio (SNR) and
increasing the uplink capacity of the UMTS network.
NOTE
l For 3900 series base stations, the WBBPd/WBBPf must be configured on slot 2 or slot 3 on the
BBU3900 to support the uplink data IC integrated interference cancellation function. The uplink
resource group must contain the WBBPd/WBBPf. Therefore, cell of the group can support the IC
feature. For details, see Adding a Baseband Board to a 3900 Series Base Station.
l If the DBS3800 is configured with two EBBCd boards, it is recommended that two uplink resource
groups be allocated to the two boards separately. In this way, both the boards support HSUPA uplink
interference cancellation. For details about how to configure the active and standby BTSs, see Adding
an EBBC or EBBCd.
l If the BTS3812E or BTS3812AE is configured with two EULPd boards, it is recommended that two
uplink resource groups be allocated to the two boards separately. In this way, both the boards support
HSUPA uplink interference cancellation. For details about how to configure the active and standby
BTSs, see Adding a Baseband Board to the BTS3812E or BTS3812AE.
Procedure
l Activation Procedure
1. If the UMTS cell has been activated, run the BSC6900 MML command DEA
UCELL (CME single configuration: UMTS Cell Configuration Express > Cell
Basic Information > Cell Basic Information. Set Validation indication to
Deactivated; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches) to deactivate the cell.
2. Run the NodeB MML command MOD LOCELL (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Radio Layer > xx Sector > Locell; CME
batch modification center: 3.17 Modifying Physical NodeB Parameters in
Batches) to modify the local cell. In this step, set IC to TRUE.
3. Run the BSC6900 MML command ACT UCELL (CME single configuration: UMTS
Cell Configuration Express > Cell Basic Information > Cell Basic Information.
Set Validation indication to Activated; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches) to activate the cell.
4. Run the NodeB MML command SET RESALLOCRULE (CME single
configuration: NodeB Configuration Express > IUB_NodeB > Basic
Information > Radio Management > RESALLOCRULE; CME batch modification
center: not supported). In this step, set Auto Rebuild Cell Switch to ON(ON) and set
Cs User Number Threshold and Ps User Number Threshold. If the number of CS
users or the number of PS CELL_DCH users in the downlink resource group is equal
or smaller than the corresponding threshold, the local cells are reestablished
automatically.
l Verification Procedure
1. Run the NodeB MML command DSP LOCELL to query the status of a specified
local cell.
Expected result: The value of IC MODE is ENABLED.
2. Run the NodeB MML command LST RESALLOCRULE.
Expected result: The value of Auto Rebuild Cell Switch is ON.
3. Select Service > Realtime Specific Monitoring > Cell RTWP from the navigation
tree in Maintenance tab on NodeB LMT, as shown in Figure 118-1. The column
1-3 indicates the state of this feature disabled, the column 1-4 indicates the state of
this feature enabled. If the value of column 1-4 is less than the value of column 1-3,
it indicates the feature has been enabled.
l Deactivation Procedure
1. Run the NodeB MML command MOD LOCELL (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Radio Layer > xx Sector > Locell; CME
batch modification center: 3.17 Modifying Physical NodeB Parameters in
Batches) to modify the local cell. In this step, set IC to FALSE.
----End
Example
//Activation procedure
DEA UCELL: CellId=1;
MOD LOCELL: LOCELL=1, SECT=LOCAL_SECTOR, IC_MODE=TRUE;
ACT UCELL: CellId=1;
SET RESALLOCRULE: SW=ON, CSUSERNUM=0, PSUSERNUM=0;
//Verification procedure
DSP LOCELL: LOCELL=1;
LST RESALLOCRULE:;
//Deactivation procedure
MOD LOCELL: LOCELL=1, SECT=LOCAL_SECTOR, IC_MODE=FALSE;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010636
SRB over HSUPA.
Prerequisites
l Dependencies on Hardware
BSC6900
This feature does not depend on the hardware.
Requirements for the NodeB
The 38XX series NodeB supports this feature, and the EBBI, EBOI, EULP or
EULPd, EBBC or EBBCd is required.
The 3900 series NodeB supports this feature, and the WBBPb, WBBPd or WBBPf
is required.
l Dependencies on Other Features
The WRFD-010612 HSUPA Introduction Package feature must be configured before
this feature is configured.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The transmission mapping to support SRB over HSUPA has been configured.
Context
This feature provides high signaling rate and shortens call setup delay. Compared with the
function of carrying SRBs on DCHs, this feature saves code resources and reduces cell load.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UFRCCHLTYPEPARA (CME single
configuration: UMTS Radio Global Configuration Express > Basic Resource
Control Parameter Configuration > Channel Type Parameters; CME batch
If the feature is effective in the case of RRC connection establishment, set Effective Flag of
Signaling RB Channel Type to TRUE.
l Verification Procedure
1. Run the BSC6900 MML command LST UFRCCHLTYPEPARA to query whether
the SRBs are carried over HSUPA.
2. Use a UE with the HSPA function to set up an RRC connection on the enhanced DCH
(E-DCH).
View the RRC_RRC_CONN_SETUP message from the Uu interface trace data. If
the EDCH information is contained in the message, this feature is activated.
l Deactivation Procedure
1. Run the BSC6900 MML command SET UFRCCHLTYPEPARA (CME single
configuration: UMTS Radio Global Configuration Express > Basic Resource
Control Parameter Configuration > Channel Type Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches) to set Type of
Channel Preferably Carrying Signaling RB to DCH(UL_DCH,DL_DCH) and
Effective Flag of Signaling RB Channel Type to FALSE.
----End
Example
//Activating SRB over HSUPA
SET UFRCCHLTYPEPARA: SrbChlType=HSUPA, SrbChlTypeRrcEffectFlag=TRUE;
//Verifying SRB over HSUPA
LST UFRCCHLTYPEPARA:;
//Deactivating SRB over HSUPA
SET UFRCCHLTYPEPARA: SrbChlType=DCH, SrbChlTypeRrcEffectFlag=FALSE;
This section describes how to activate, verify, and deactivate the optional feature WRFD-140202
Control Channel Parallel Interference Cancellation (Phase 2). Control Channel Parallel
Interference Cancellation is short for CCPIC.
Prerequisites
l Dependencies on Hardware
The 3900 series base station (except for BTS3902E) must be configured with the
WBBPd or WBBPf board.
To support inter-board IC, the WBBPd or WBBPf board must be configured for the
uplink resource group that supports inter-board IC. In addition, at least one WBBPd or
WBBPf board must be configured in slot 2 or 3.
It is recommended that the WBBPa or WBBPb board be replaced with a WBBPd or
WBBPf board to fully utilize CCPIC (Phase 2). Assume that a WBBPa or WBBPb board
and a WBBPd or WBBPf board are inserted into one BBU to form a UL resource group.
To share the CCPIC gains of the WBBPd or WBBPf board when NodeB IC Mode is
set to FULL_IC(All board can share IC gain), UEs with their data channel carried
on the WBBPa or WBBPb board must set up another DPCCH on the WBBPd or WBBPf
board for power control. Of the UEs, those with their downlink services carried on an
HSDPA channel must set up another HS-DPCCH on the WBBPd or WBBPf board. The
extra channels consume extra processing resources, reducing the total number of users
supported by the system.
l Dependencies on Other Features
The feature WRFD-010210 Control Channel Parallel Interference Cancellation
(CCPIC) has been configured before this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others Prerequisites
None
Context
l Precautions
Gains from CCPIC (Phase 2) and Adaptive Configuration of Traffic Channel Power
offset for HSUPA may decrease.
If CCPIC (Phase 2) is enabled, gains from Adaptive Configuration of Traffic
Channel Power offset for HSUPA decrease.
If Adaptive Configuration of Traffic Channel Power offset for HSUPA is enabled,
gains from CCPIC (Phase 2) decrease.
System throughput is always greater when CCPIC (Phase 2) is enabled together with
Adaptive Configuration of Traffic Channel Power offset for HSUPA, as compared
with when CCPIC (Phase 2) is not enabled together with Adaptive Configuration of
Traffic Channel Power offset for HSUPA or none of the features is enabled.
Gains from CCPIC (Phase 2) and HSUPA Adaptive Transmission may decrease.
If CCPIC (Phase 2) is enabled, gains from HSUPA Adaptive Transmission decrease.
If HSUPA Adaptive Transmission is enabled, gains from CCPIC (Phase 2) decrease.
System throughput is always greater when CCPIC (Phase 2) is enabled together with
HSUPA Adaptive Transmission, as compared with when CCPIC (Phase 2) is not
enabled together with HSUPA Adaptive Transmission or none of the features is
enabled.
The cell throughput decreases for 5 to 10 seconds and all UEs carried on a WBBPa or
WBBPb board experience call drops when the following conditions are true:
A WBBPd or WBBPf board and the WBBPa or WBBPb board are inserted into one
BBU to form a UL resource group.
The setting for ICMODE changes when the CCPIC (Phase 2) feature is enabled.
l Data Preparation
Scenario 1: No WBBPa or WBBPb board is configured for a base station.
The configuration is not required.
Scenario 2: A WBBPa or WBBPb board is configured for a base station. The WBBPa
or WBBPb board cannot benefit from CCPIC (Phase 2) gains by default.
Parameter Name Parameter ID Recommended Source
Parameter
Settings
Scenario 2: A WBBPa or WBBPb board is configured for a base station. The WBBPa
or WBBPb board cannot benefit from CCPIC (Phase 2) gains.
Parameter Name Parameter ID Recommended Source
Parameter
Settings
Procedure
l Activation Procedure
After the license is activated, this feature has been activated.
NOTE
Even if all prerequisites are ready, CCPIC (Phase 2) may not be available temporarily to the cell to
avoid interruption of ongoing services. To ensure that the cell can be adjusted to support CCPIC
(Phase 2), the Auto Rebuild Cell Switch must be set to ON(ON).
1. Run the NodeB MML command SET RESALLOCRULE (CME single
configuration: NodeB Configuration Express > IUB_NodeB > Basic
Information > Radio Management > RESALLOCRULE; CME batch modification
center: not supported). In this step, set Auto Rebuild Cell Switch to ON(ON) and set
Cs User Number Threshold and Ps User Number Threshold. If the number of CS
users or the number of PS CELL_DCH users in the downlink resource group is equal
or smaller than the corresponding threshold, the local cells are reestablished
automatically.
2. Select operations as configured.
Scenario 1: The configuration ends.
Scenario 2: Run the NodeB MML command SET ICMODE (CME single
configuration: NodeB Configuration Express > IUB_NodeB > Basic
Information > Basic Information > Radio Management > ICMODE; CME
batch modification center: not supported). In this step, set NodeB IC Mode to
PART_IC(Old board can not share IC gain).
Scenario 3: Run the NodeB MML command SET ICMODE (CME single
configuration: NodeB Configuration Express > IUB_NodeB > Basic
Information > Basic Information > Radio Management > ICMODE; CME
batch modification center: not supported). In this step, set NodeB IC Mode to
FULL_IC(All board can share IC gain).
l Verification Procedure
Check whether the CCPIC (Phase 2) feature has been activated by using the RNC or NodeB
LMT. If the base station is configured with the RRU3801C, the following verification mode
does not apply.
NOTE
Observe the activation when there are a large number of UEs because CCPIC (Phase 2) gain is obvious
only when there are a large number of UEs.
On the RNC LMT:
1. On the RNC LMT, click Monitor, choose Cell Performance Monitoring >
RTWP, enter the cell ID, and click Submit.
2. Check whether a valid value is displayed for Cell measured RTWP After First
Stage Interference Cancellation.
Expected result:
A valid value is displayed, indicating that the CCPIC (Phase 2) feature is
functioning properly. When there are a large number of UEs, Cell measured
RTWP After First Stage Interference Cancellation is smaller than Cell
Measured RTWP. The RTWP decrease further indicates that this feature has been
activated. Figure 120-1 shows the RTWP monitoring result displayed on the RNC
LMT.
Figure 120-2 Figure 7-3 Cell-level RTWP monitoring on the NodeB LMT
l Deactivation Procedure
None
----End
Example
//Activation procedure
SET RESALLOCRULE: SW=ON, CSUSERNUM=0, PSUSERNUM=0;
//Scenario 2
SET ICMODE: ICMODE=PART_IC;
//Scenario 3
SET ICMODE: ICMODE=FULL_IC;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010610
HSDPA Introduction Package. (This feature cannot be configured using the CME. )
Prerequisites
l Dependencies on Hardware
NDLP and NBBI in the NodeB do not support this feature.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The UE is HSDPA-capable.
Context
High Speed Downlink Packet Access (HSDPA) is one of the important features defined in 3GPP
specifications. HSDPA can significantly increase the downlink peak rate per user, shorten the
round trip delay, and expand the system capacity. This feature package provides the basic
functions of HSDPA to meet the requirements for test or trial operation of HSDPA services.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command ADD UCELLHSDPA to set HSDPA-related
parameters based on the network plan.
2. Run the BSC6900 MML command ACT UCELLHSDPA to activate this feature.
3. Configure Iub transport for HSDPA.
In an ATM network:
a. Run the BSC6900 MML command ADD ATMTRF to configure new records
of ATM traffic based on network planning requirements.
b. Run the BSC6900 MML command LST TRMMAP to query the
transmission resource mapping.
c. Run the BSC6900 MML command ADD AAL2PATH to set associated
parameters according to the network plan. TX traffic record index and RX
traffic record index of the AAL2 path to be added must be the same as those
set in the ADD ATMTRF command. In addition, AAL2 Path Type should
be set according to the mapping between service types and AAL paths.
d. Run the NodeB MML command ADD AAL2PATH to configure an AAL2
path for HSDPA based on network planning requirements.
In an IP network:
a. Run the BSC6900 MML command LST ADJMAP to query whether
resource management mapping is configured for the adjacent node.
If configured, check the TRMMAP index of the adjacent node.
If not configured, run the BSC6900 MML command LST TRMMAP to
query the default TRMMAP ID used by the adjacent node based on the
settings of Interface Type and Transport Type. For example, if
Interface Type is set to Iub Interface, then TRMMAP ID is 1.
b. Run the BSC6900 MML command LST TRMMAP to check whether the IP
path mapping to the HSDPA service is configured according to the TRMMAP
ID used by the adjacent node.
If configured, no further action is required.
If not configured, run the BSC6900 MML command ADD IPPATH to
configure the IP path mapping to the HSDPA service.
NOTE
To ensure that HSDPA services can be set up successfully, HSDPA services must be mapped to the
corresponding AAL2 paths or IP paths. To avoid the affect on ongoing services, you can add new
AAL2 paths or IP paths.
l Verification Procedure
1. Run the BSC6900 MML command DSP UCELL to check whether this feature is
activated. If HSDPA Operational State is set to Enabled, this feature has been
activated.
l Deactivation Procedure
1. Run the BSC6900 MML command DEA UCELLHSDPA to deactivate this feature.
2. Run the BSC6900 MML command DSP UCELL to check whether the HSDPA
feature is deactivated. If HSDPA Operational State is set to Disabled, this feature
has been deactivated.
----End
Example
// Setting HSDPA-related parameters
ADD UCELLHSDPA: CellId=3000, AllocCodeMode=Automatic,
HsPdschMaxCodeNum=4, HsPdschMinCodeNum=1, CodeAdjForHsdpaSwitch=ON;
//Activating HSDPA Introduction Package
ACT UCELLHSDPA: CellId=3000;
//Configuring Iub transport for HSDPA
//ATM network
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061001 15 Codes per Cell.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The configurations of the features on which this feature depends are complete. This
feature depends on the feature WRFD-010610 HSDPA Introduction Package.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature provides code resources occupied by Huawei HSDPA services. An HS-PDSCH can
use up to 15 SF16 codes in a cell.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command MOD UCELLHSDPA (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
HSDPA Parameters; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches) to set Code Number for HS-SCCH to 1.
NOTE
l The BSC6900 MML command MOD UCELLHSDPA (CME single configuration: UMTS Cell
Configuration Express > Cell Parameters > Cell HSDPA Parameters; CME batch
modification center: 3.18 Modifying UMTS Cell Parameters in Batches) fails to be executed
when HSDPA is activated. Therefore, run the BSC6900 MML command DEA
UCELLHSDPA (CME single configuration: UMTS Cell Configuration Express > Cell
Parameters > Cell HSDPA Parameters. Set ACTSTATUS to Deactivated; CME batch
modification center: No supported) to deactivate HSDPA before configuring this feature and
run the BSC6900 MML command ACT UCELLHSDPA (CME single configuration: UMTS
Cell Configuration Express > Cell Parameters > Cell HSDPA Parameters. Set
ACTSTATUS to Activated; CME batch modification center: No supported) to reactivate
HSDPA after configuring this feature.
l The BSC6900 MML command MOD UCELLHSDPA (CME single configuration: UMTS Cell
Configuration Express > Cell Parameters > Cell HSDPA Parameters; CME batch
modification center: 3.18 Modifying UMTS Cell Parameters in Batches) fails to be executed
when CELL-FACH enhancement is activated. Therefore, run the BSC6900 MML command
DEA UCELLEFACH (CME single configuration: UMTS Cell Configuration Express > Cell
Parameters > Cell Enhanced FACH parameters. Set Validation indication to
Deactivated; CME batch modification center: No supported) to deactivate enhanced CELL-
FACH before configuring this feature and Run the BSC6900 MML command ACT
UCELLEFACH (CME single configuration: UMTS Cell Configuration Express > Cell
Parameters > Cell Enhanced FACH parameters. Set Validation indication to Activated;
CME batch modification center: No supported) to reactivate enhanced CELL-FACH after
configuring this feature.
l By default, the number of HS-SCCH codes for each cell is 4. If the default number is used, the
HS-PDSCH can use only 14 SF16 codes. To enable the HS-PDSCH to use all 15 SF16 codes,
run the BSC6900 MML command MOD UCELLHSDPA (CME single configuration: UMTS
Cell Configuration Express > Cell Parameters > Cell HSDPA Parameters; CME batch
modification center: 3.18 Modifying UMTS Cell Parameters in Batches) to set the value of
Code Number for HS-SCCH to 1.
2. Run the BSC6900 MML command MOD UCELLHSDPA (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
HSDPA Parameters; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches) to set Allocate Code Mode to Manual(Manual) and Code
Number for HS-PDSCH to 15.
l Verification Procedure
1. Initialize UMTS monitoring on the BSC6900 LMT, as shown in Figure 122-1. Click
Submit. A real-time monitoring window is displayed.
2. Check whether 15 SF16 codes are occupied by the HS-PDSCH in the Cell
Performance Monitoring window.
Expected result: The HS-PDSCH occupies 15 SF16 codes.
l Deactivation Procedure
1. This feature does not need to be deactivated.
----End
Example
//Verifying 15 Codes per Cell
MOD UCELLHSDPA: CellId=1, HsScchCodeNum=1;
MOD UCELLHSDPA: CellId=1, AllocCodeMode=Manual, HsPdschCodeNum=15;
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061018 Time and HS-PDSCH Codes Multiplex.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The configurations of the features on which this feature depends are complete. This
feature depends on the feature WRFD-010610 HSDPA Introduction Package.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature enables the allocation of different codes in the same TTI to different users or the
multiplexing of the same code in different TTIs for different users to increase the code resource
utilization and system throughput.
Procedure
l Activation Procedure
This feature does not need to be activated.
l Verification Procedure
This feature does not need to be verified.
l Deactivation Procedure
This feature does not need to be deactivated.
----End
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061009 HSDPA H-ARQ & Scheduling (MAX C/I, RR, and PF).
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
The configurations of the features on which this feature depends are complete. This
feature depends on the feature WRFD-010610 HSDPA Introduction Package.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
Huawei provides multiple HSDPA scheduling algorithms such as maximum C/I (MAXCI),
round-robin (RR), proportional fair (PF), and Enhanced Proportional Fair (EPF).Before the
HSDPA feature is enabled, HARQ must be enabled and HSDPA scheduling algorithms must be
set.
Procedure
l Activation Procedure
NOTE
Example
//Activation procedure
SET MACHSPARA: LOCELL=0, SM=MAXCI;
//Verification procedure
LST MACHSPARA: LOCELL=0;
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061005 HSDPA Static Code Allocation and RNC-Controlled Dynamic Code
Allocation.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
The feature WRFD-010610 HSDPA Introduction Package must be configured before
this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature provides two code allocation strategies: HSDPA static code allocation and RNC-
controlled dynamic code allocation. When R99 and HSDPA services co-exist, this feature
enables full use of channelization code resources to expand system capacity.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command MOD UCELLHSDPA (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
HSDPA Parameters; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches). In this step, set Allocate Code Mode to Manual or
Automatic.
If Allocate Code Mode is set to Manual, set Code Number for HS-PDSCH to
specify the number of HS-PDSCH codes.
If Allocate Code Mode is set to Automatic, set Code Max Number for HS-
PDSCH to specify the maximum number of HS-PDSCH codes and set Code Min
Number for HS-PDSCH to specify the minimum number of HS-PDSCH codes.
l Verification Procedure
1. Run the BSC6900 MML command LST UCELLHSDPA to query code allocation
mode.
2. On the BSC6900 LMT, click to display Cell Performance Monitoring. Set Monitor
Item to Cell Code Tree Monitor and click Submit. The Cell Performance Monitoring
tab page is displayed.
3. View the number of codes allocated to the HS-PDSCH in the cell. If Allocate Code
Mode is set to Manual, the monitoring window of cell code tree usage shows that the
number of codes allocated to the HS-PDSCH remains unchanged. If Allocate Code
Mode is set to Automatic, the monitoring window of cell code tree usage shows that
the number of codes allocated to the HS-PDSCH varies with service access requests
in the cell. For example, the number of codes allocated to the HS-PDSCH increases
with the increase of HSDPA access requests and decreases with the decrease of
HSDPA access requests.
l Deactivation Procedure
This feature does not need to be deactivated.
----End
Example
//Activating HSDPA Static Code Allocation and RNC-Controlled Dynamic Code
Allocation
MOD UCELLHSDPA: CellId=11, AllocCodeMode=Manual, HsPdschCodeNum=5,
HsScchCodeNum=4;
MOD UCELLHSDPA: CellId=11, AllocCodeMode=Automatic, HsPdschMaxCodeNum=5,
HsPdschMinCodeNum=1;
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061004 HSDPA Power Control.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
The feature WRFD-010610 HSDPA Introduction Package must be configured before
this feature is configured.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
After an HSDPA service is introduced, the total downlink transmit power of each cell is classified
into common channel power, dedicated physical channel (DPCH) power, and power of HSDPA
physical channels (HS-PDSCH and HS-SCCH). To achieve high HSDPA performance, power
resources except those reserved for common channels are dynamically allocated to DPCHs and
HSDPA physical channels. For R99 services, the DPCH power can be adjusted by means of
inner-loop and outer-loop power control. HSDPA channel power resources can be dynamically
allocated and adjusted among users by using the NodeB scheduling algorithm.
HS-PDSCH power is controlled by the transport format and resource combination (TFRC)
algorithm and therefore does not require power control.
This feature enables operators to configure the appropriate power control mode of the HS-SCCH,
increasing the power efficiency and system capacity and improving the user experience.
Procedure
l Activation Procedure
1. Activating the adaptive HS-SCCH power control based on the channel quality
indicator (CQI)
l Verification Procedure
1. Verifying the adaptive HS-SCCH power control based on the CQI
a. Use an HSUPA-capable UE to set up a PS service over the HS-SCCH.
b. Move the UE between the cell center and the cell edge to view the power change
on HS-SCCHs. Expected result: The HS-SCCH power changes with the CQI.
2. Verifying the fixed HS-SCCH power control
a. Use an HSUPA-capable UE to set up a PS service over the HS-SCCH.
b. Move the UE between the cell center and the cell edge to view the power change
on the HS-SCCH. Expected result: The HS-SCCH power remains unchanged.
l Deactivation Procedure
----End
Example
//Activating HSUPA Power Control
//Setting the adaptive HS-SCCH power control based on the CQI
MOD UCELLHSDPA: CellId=111, AllocCodeMode=Manual, HsPdschCodeNum=5,
HsScchCodeNum=1;
SET MACHSPARA: LOCELL=111, HSSCCHPWRCMINDCH=CQI, HSSCCHFERTRGTINDCH=10;
HsScchCodeNum=1;
SET MACHSPARA: LOCELL=111, HSSCCHPWRCMINDCH=FIXED, SCCHPWR=0;
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061003 HSDPA Admission Control.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
The feature WRFD-010610 HSDPA Introduction Package must be configured before
this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature implements admission control over HSDPA users in the aspects such as the number
of HSDPA users, remaining power resources, Iub interface resources, and service rate thresholds.
This feature can ensure the QoS of existing HSDPA users while fully utilizing the resources.
Procedure
l Activation Procedure
1. Activate power resource admission.
Run the BSC6900 MML command MOD UCELLALGOSWITCH (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Algorithm Switches; CME batch modification center: 3.18 Modifying UMTS
Cell Parameters in Batches). In this step, set Uplink CAC algorithm switch and
Downlink CAC algorithm switch according to the network planning.
For HSDPA services, run the BSC6900 MML command MOD
UCELLALGOSWITCH (CME single configuration: UMTS Cell
Configuration Express > Cell Parameters > Cell Algorithm Switches; CME
NOTE
Run the BSC6900 MML command MOD IPPATH (CME single configuration: NodeB
Configuration Express > IUB_RNC > IP Transport > IP Path; CME batch modification
center: not supported) or MOD AAL2PATH (CME single configuration: NodeB
Configuration Express > IUB_RNC > ATM Transport > AAL2 Path; CME batch
modification center: not supported) to change the Iub interface bandwidth.
l Verification Procedure
1. Enable two UEs UE1 and UE2 in idle mode to camp on the test cell, and the test cell
must support HSDPA.
2. On the HLR, set PS service type to background or interactive.
3. Run the BSC6900 MML command MOD UCELLCAC to set the maximum number
of HSDPA users to 1.
4. Use UE1 to initiate an HSDPA PS service. After the service is set up successfully,
check the RRC_RB_SETUP message over the Uu interface. You can view that the
new-H-RNTI IE is under the rb-mappinginfo IE, and the value of the dl-
TransportChannel-Type IE is hsdsch.
5. Use UE2 to initiate an HSDPA PS service. The service should fail to set up. Check
the RRC_RB_SETUP message over the Uu interface. You can view that the new-H-
RNTI IE is not under the rb-mappinginfo IE, and the value of the dl-
TransportChannel-Type IE is dch.
Example
//Activating power resource admission
MOD UCELLALGOSWITCH: CellId=11, NBMUlCacAlgoSelSwitch=ALGORITHM_FIRST,
NBMDlCacAlgoSelSwitch=ALGORITHM_SECOND;
MOD UCELLALGOSWITCH: CellId=11,
NBMCacAlgoSwitch=HSDPA_UU_ADCTRL-1&HSDPA_GBP_MEAS-1&HSDPA_PBR_MEAS-1;
MOD UCELLCAC: CellId=11, HsdpaStrmPBRThd=70, HsdpaBePBRThd=30,
MaxHsdpaUserNum=64, MaxUlTxPowerforConv=24, MaxUlTxPowerforInt=24;
//Activating NodeB credit resource admission
SET UCACALGOSWITCH: CacSwitch=NODEB_CREDIT_CAC_SWITCH-1;
MOD UCELLALGOSWITCH: CellId=11, NBMCacAlgoSwitch=CRD_ADCTRL-1;
MOD UCELLCAC: CellId=11, UlHoCeResvSf=SF16, DlHoCeCodeResvSf=SF32;
//Deactivating power resource admission
MOD UCELLALGOSWITCH: CellId=11, NBMUlCacAlgoSelSwitch=ALGORITHM_OFF,
NBMDlCacAlgoSelSwitch=ALGORITHM_OFF;
//Deactivating NodeB credit resource admission
SET UCACALGOSWITCH: CacSwitch=NODEB_CREDIT_CAC_SWITCH-0;
MOD UCELLALGOSWITCH: CellId=11, NBMCacAlgoSwitch=CRD_ADCTRL-0;
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061020 Improvement of User Experience in Low Traffic Service.
Prerequisites
l Dependencies on Hardware
Dependencies on BSC6900 Hardware
Only BSC6900 support this feature.
Dependencies on NodeB Hardware
The BTS3812E, BTS3812A, and BTS3812AE should be configured with the EULP,
EBBI, EBOI or EULPd board.
The BBU3806 is configured with the EBBC or EBBCd board.
The BBU3900 is configured with the WBBPb, WBBPd or WBBPf board.
l Dependencies on Other Features
WRFD-010610 HSDPA Introduction Package
WRFD-010612 HSUPA Introduction Package
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
l The NodeB detects HSPA services with low traffic, such as gaming services and instant
messaging services (such as MSN).
l The NodeB enables low traffic services to obtain more resources based on the scheduling
and flow control principles of HSPA, which reduces delay in low traffic services.
Procedure
l Activation Procedure
When the burst packet size of a user is set to 0, it indicates that the NodeB stops identifying
the low traffic services of the user.
----End
Example
//Activation procedure
SET UEQOSENHANCEPARA: ULGOLDUEBPS=10, ULSILVERUEBPS=11, ULCOPPERUEBPS=12,
DLGOLDUEBPS=13, DLSILVERUEBPS=14, DLCOPPERUEBPS=15;
//Verification procedure
LST UEQOSENHANCEPARA:;
//Deactivation procedure
SET UEQOSENHANCEPARA: ULGOLDUEBPS=0, ULSILVERUEBPS=0, ULCOPPERUEBPS=0,
DLGOLDUEBPS=0, DLSILVERUEBPS=0, DLCOPPERUEBPS=0;
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061010 HSDPA Flow Control.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
The feature WRFD-010610 HSDPA Introduction Package must be configured before
this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
For each MAC-hs queue, HSDPA Flow Control calculates the pre-allocated Iub bandwidth based
on the Uu transmission rate and the amount of data buffered in the NodeB. The Uu transmission
rate of the MAC-hs queue is determined by the scheduling algorithm. For each MAC-hs queue,
if the Iub transmission rate is higher than the Uu transmission rate, the data packets are buffered.
Too much data buffered in the NodeB leads to transmission delay and even packet loss.
Therefore, each MAC-hs queue should not have too much data buffered in the NodeB. However,
it should retain a certain amount of data to prevent wasting the Uu resources due to not having
data to transmit.
Procedure
l Activation Procedure
Expected result:
Expected result:
The throughput of UE1 decreases after UE2 accesses the network. When the
throughput of the two UEs is stable, the total bandwidth of the two UEs is 4 MHz. If
user priority, service type and Security Parameter Index (SPI) of the two UEs are the
same, the final ratio of the two UEs' throughput is 1:1.
l Deactivation Procedure
You can deactivate the current algorithm by selecting one of the other flow control
algorithms.
----End
Example
//Activating HSDPA Flow Control and setting the flow control mode to
adaptive flow control
SET HSDPAFLOWCTRLPARA: SRN=0, SN=6, BEAR=ATM, SBT=BASE_BOARD, PT=IMA,
PN=0, SWITCH= BW_SHAPING_ONOFF_TOGGLE, TD=2, DR=1, ITM=TERRESTRIAL;
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061006 HSDPA Mobility Management.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The feature WRFD-010610 HSDPA Introduction Package must be configured before
this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature enables an HSDPA-capable UE to be handed over to an R99 cell or another HSDPA
cell.
This feature also enables an HSDPA-capable UE to change cells with a small probability of
service interruption.
Procedure
l Activation Procedure
1. The methods of activating intra-frequency, inter-frequency, and inter-RAT handovers
are the same for HSDPA users and R99 users. For details, see the following sections:
35 Configuring Intra Frequency Hard Handover
236 Configuring Inter Frequency Hard Handover Based on Coverage
237 Configuring Inter Frequency Hard Handover Based on DL QoS
247 Configuring Inter Frequency Load Balance
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061002 HSDPA UE Category 1 to 28.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The configurations of the features on which this feature depends are complete. This
feature depends on the feature WRFD-010610 HSDPA Introduction Package.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature can provide proper HSDPA services for the UEs of category 1 to category 28.
Procedure
l Activation Procedure
This feature does not need to be activated.
l Verification Procedure
This feature does not need to be verified.
l Deactivation Procedure
This feature does not need to be deactivated.
----End
This section describes how to activate, verify, and deactivate the optional feature WRFD-010629
DL 16QAM Modulation.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
WRFD-010610 HSDPA Introduction Package
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The UE should have the capability of HSDPA besides Category 11 and Category
12:category 1,2,3,4,5,6,7,8,9,10,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28.
Context
Compared with QPSK, 16QAM is a higher-order downlink data modulation scheme. This feature
enables the peak rate on the Uu interface to reach 14.4 Mbit/s.
l The HS-PDSCH is used to carry the HS-DSCH data. The HS-PDSCH may use QPSK or
16QAM modulation symbols.
l When the UE is in poor radio environment, the transmission can adopt the low-order QPSK
modulation mode and small transport blocks to ensure communication quality.
l When the UE is in good radio environment, the transmission can adopt the high-order
16QAM modulation mode and large transport blocks to achieve high peak rate.
l The UE of category 10 can support a maximum of 15 HS-PDSCH codes and 16QAM
modulation mode. The supported peak rate on the air interface can reach 14.4 Mbit/s.
Procedure
l Activation Procedure
NOTE
HSDPA Introduction Package must be activated before activating this feature. For the method of
activating HSDPA Introduction Package, see the section "Configuring HSDPA Introduction
Package."
1. Run the NodeB MML command SET MACHSPARA (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Radio Layer > Locell Algorithm
Parameters > MAC Parameters > MACHSPARA; CME batch modification center:
3.17 Modifying Physical NodeB Parameters in Batches). In this step, set 16QAM
Switch to OPEN(open).
l Verification Procedure
NOTE
l For the 16QAM modulation of the HSDPA UE, the NodeB license control item must be enabled.
l As defined in 3GPP 25.306, the UE in category 8 can support both QPSK and 16QAM modulation
schemes. Only 16QAM modulation, however, enables the throughput of category 8 UE to reach
5 Mbit/s.
NOTE
Only in case of good environment quality of the channel, the throughput of category 8 UE can
reach 5 Mbit/s.
Perform the following steps to check whether the download rate can reach 5 Mbit/s.
1. Use the UE to start a PS interactive service of DL 7200 kbit/s. The PS service is carried
on the HS-DSCH. The UE keeps in Cell-DCH state.
2. Start FTP (10 threads) to download given files, which are larger than 1 GB. By
monitoring the DL throughput and bandwidth, you find that the PS downloading
service is normal and the bit rate is higher than 5 Mbit/s.
l Deactivation Procedure
1. Run the NodeB MML command SET MACHSPARA (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Radio Layer > Locell Algorithm
Parameters > MAC Parameters > MACHSPARA; CME batch modification center:
3.17 Modifying Physical NodeB Parameters in Batches). In this step, set 16QAM
Switch to CLOSE(close).
----End
Example
//Activating procedure
SET MACHSPARA: CME16QAMSW=OPEN;
//Deactivating procedure
SET MACHSPARA: CME16QAMSW=CLOSE;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010631
Dynamic Code Allocation Based on NodeB.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
WRFD-010610 HSDPA Introduction Package
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature implements dynamic code allocation on the NodeB side. The NodeB adjusts the
allocation of code resources in each TTI according to available code resources and scheduling
algorithms. This feature can further improve the utilization of code resources.
Procedure
l Activation Procedure
NOTE
HSDPA Introduction Package must be activated before activating this feature. For the method of
activating HSDPA Introduction Package, see the section "Configuring HSDPA Introduction
Package."
1. Run the NodeB MML command SET MACHSPARA (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Radio Layer > Locell Algorithm
Parameters > MAC Parameters > MACHSPARA; CME batch modification center:
3.17 Modifying Physical NodeB Parameters in Batches). In this step, set Dynamic
Code Switch to OPEN(open).
l Verification Procedure
1. Run the NodeB MML command SET MACHSPARA. In this step, set Dynamic
Code Switch to CLOSE(close).
2. Run the BSC6900 MML command MOD UCELLHSDPA.
set Allocate Code Mode to Manual.
set Code Number for HS-PDSCH to 5.
3. Use a UE that belongs to category 8 or is capable of higher HSDPA performance to
download 200 MB files from the FTP server in the serving cell.
4. Select Service > Trace Management > Interface Trace Task > User from the
navigation tree in Maintenance tab on NodeB LMT, select (DL)Hsdpa User
Enhanced Schedule Data message, as shown in Figure 133-1.
6. Run the NodeB MML command SET MACHSPARA. In this step, set Dynamic
Code Switch to OPEN(open).
7. Trace (DL)Hsdpa User Enhanced Schedule Data message,
ucMaxPdschCodeNum is less than the value of 5, it indicates the feature has been
enabled. as shown in Figure 133-3.
l Deactivation Procedure
1. Run the NodeB MML command SET MACHSPARA (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Radio Layer > Locell Algorithm
Parameters > MAC Parameters > MACHSPARA; CME batch modification center:
3.17 Modifying Physical NodeB Parameters in Batches). In this step, set Dynamic
Code Switch to CLOSE(close).
----End
Example
//Activation procedure
//Operations on the NodeB side
SET MACHSPARA: DYNCODESW=OPEN;
//Verification procedure
//Operations on the NodeB side
SET MACHSPARA: DYNCODESW=CLOSE;
//Operations on the BSC6900 side
MOD UCELLHSDPA: CellId=0, AllocCodeMode=Manual, HsPdschCodeNum=5;
//Operations on the NodeB side
SET MACHSPARA: DYNCODESW=OPEN;
//Deactivation procedure
//Operations on the NodeB side
SET MACHSPARA: DYNCODESW=CLOSE;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010611
HSDPA Enhanced Package.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The configurations of the features on which this feature depends are complete. This
feature depends on the feature WRFD-010610 HSDPA Introduction Package.
l License
This feature is not under license control.
l Other Prerequisites
UE should support the functions connected with HSDPA Enhanced package.
Context
HSDPA enhanced package is introduced on the basis of WRFD-010610 HSDPA Introduction
Package, and provides enhancement features to meet the QoS and HSDPA network
requirements. Related features include:
l WRFD-01061103 Scheduling based on EPF and GBR
l WRFD-01061111 HSDPA State Transition
l WRFD-01061112 HSDPA DRD
l WRFD-01061113 HS-DPCCH Preamble Support
Procedure
l For details about activate, verify, and deactivate procedures, see the following sections:
135 Configuring Scheduling based on EPF and GBR
136 Configuring HSDPA State Transition
137 Configuring HSDPA DRD
NOTE
HS-DPCCH Preamble Support does not need to be activated, verified, or deactivated.
----End
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061103 Scheduling based on EPF and GBR.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
WRFD-010610 HSDPA Introduction Package
l License
This feature is not under license control.
Context
The operator can set different QoS parameters such as priority, weight, and Guaranteed Bit Rate
(GBR) for different users. Based on the QoS parameters, the Enhanced Proportional Fair (EPF)
algorithm can accurately allocate resources by proportion. This feature allows different users to
obtain accurate differentiated experiences.
Procedure
l Activation Procedure
1. Run the NodeB MML command SET MACHSPARA (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Radio Layer > Locell Algorithm
Parameters > MAC Parameters > MACHSPARA; CME batch modification center:
3.17 Modifying Physical NodeB Parameters in Batches). In this step, set
Scheduling Method to EPF(Enhanced PF).
l Verification Procedure
1. Run the NodeB MML command LST MACHSPARA to check that Scheduling
Method is set to EPF.
l Deactivation Procedure
1. Run the NodeB MML command SET MACHSPARA (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Radio Layer > Locell Algorithm
Parameters > MAC Parameters > MACHSPARA; CME batch modification center:
3.17 Modifying Physical NodeB Parameters in Batches). In this step, set
Scheduling Method to an option other than EPF(Enhanced PF).
----End
Example
//Activation procedure
SET MACHSPARA: SM=EPF;
//Verification procedure
LST MACHSPARA;
//Deactivation procedure
SET MACHSPARA: SM=PF;
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061111 HSDPA State Transition.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The feature WRFD-010610 HSDPA Introduction Package has been configured before
this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
l This feature enables the switching between the DCH and HS-DSCH and makes it possible
for UEs to enjoy high-speed services.
l This feature also enables a UE with an ongoing BE service or streaming service to move
to the CELL_FACH state to save system resources when the UE does not have data
transmission for a long period.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, select the
DRA_HSDPA_STATE_TRANS_SWITCH and
DRA_PS_BE_STATE_TRANS_SWITCH check boxes under the parameter
Dynamic Resource Allocation Switch.
l Verification Procedure
l Deactivation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, deselect the
DRA_HSDPA_STATE_TRANS_SWITCH and
DRA_PS_BE_STATE_TRANS_SWITCH check boxes under the parameter
Dynamic Resource Allocation Switch.
----End
Example
//Activating HSDPA State Transition
SET UCORRMALGOSWITCH:
DraSwitch=DRA_HSDPA_STATE_TRANS_SWITCH-1&DRA_PS_BE_STATE_TRANS_SWITCH-1;
//Deactivating HSDPA State Transition
SET UCORRMALGOSWITCH:
DraSwitch=DRA_HSDPA_STATE_TRANS_SWITCH-0&DRA_PS_BE_STATE_TRANS_SWITCH-0;
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061112 HSDPA DRD.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
The following features must be configured before this feature is activated:
WRFD-010610 HSDPA Introduction Package and WRFD-020400 DRD Introduction
Package.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature enables HSDPA-suitable services to be established on the HS-DSCH cell as much
as possible if a UE is HS-DSCH capable, achieving better service performance.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, set Direct retry switch to
DR_RAB_SING_DRD_SWITCH or DR_RAB_COMB_DRD_SWITCH
according to the network plan.
NOTE
The DR_RAB_SING_DRD_SWITCH and the DR_RAB_COMB_DRD_SWITCH can be
turned on at the same time according to the network plan.
l Verification Procedure
This feature also supports the following scenario: If a UE in an R99 cell (cell 1) originates HSDPA
streaming services or BE services, the UE can camp on an HSDPA cell (cell 2) through directed
retry. In this scenario, cell 2 is the inter-frequency neighboring cell for blind handover of cell 1 and
admission to cell 2 is allowed.
l Deactivation Procedure
1. The feature does not need to be deactivated.
----End
Example
//Activating HSDPA DRD
SET UCORRMALGOSWITCH: DrSwitch= DR_RAB_SING_DRD_SWITCH-1;
SET UCORRMALGOSWITCH: DrSwitch= DR_RAB_COMB_DRD_SWITCH-1;
//Verifying HSDPA DRD
MOD UINTERFREQNCELL: RNCId=1, CellId=1, NCellRncId=1, NCellId=2,
BlindHoFlag=TRUE;
SET UFRCCHLTYPEPARA: DlBeTraffThsOnHsdpa=D384;
MOD UCELLCAC: CellId=1, MaxHsdpaUserNum=0;
MOD UCELLALGOSWITCH: CellId=1, NBMCacAlgoSwitch=HSDPA_UU_ADCTRL-1;
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061113 HS-DPCCH Preamble Support.
Prerequisites
l Dependencies on Hardware
Dependency on RNC
This feature does not depend on the RCN hardware.
Dependency on NodeB
The BTS3812E, BTS3812A and BTS3812AE must be configured with EBBI board,
EBOI board, EULP or EULPd board.
The BBU3806 needs to configure EBBC or EBBCd board.
The BBU3900 needs to configure WBBPb ,WBBPd or WBBPf board.
l Dependencies on Other Features
The following features must be configured before this feature is activated:
WRFD-010610 HSDPA Introduction Package.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others
The UE should have the capability of HSDPA Category 6 (or later) and support this
feature.
Context
This feature enables the transmission of dedicated preamble subframes before ACK/NACK
subframes are transmitted on the HS-DPCCH, improving transmission reliability.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command ADD UCELLHSDPA (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
HSDPA Parameters; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches) or Run the BSC6900 MML command MOD
UCELLHSDPA (CME single configuration: UMTS Cell Configuration Express >
Cell Parameters > Cell HSDPA Parameters; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches). In this step, set HARQ Preamble
Capability Indication to Mode1.
l Verification Procedure
1. Start UE message tracing on the BSC6900 LMT, and verify the value of the
information element (IE) harq-Preamble-Mode contained in the message
RRC_RRC_CONN_SETUP.
The expect result: The value of the information element (IE) harq-Preamble-Mode
is 1. As shown in Figure 138-1.
l Deactivation Procedure
1. Run the BSC6900 MML command ADD UCELLHSDPA (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
HSDPA Parameters; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches) or Run the BSC6900 MML command MOD
UCELLHSDPA (CME single configuration: UMTS Cell Configuration Express >
Cell Parameters > Cell HSDPA Parameters; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches). In this step, set HARQ Preamble
Capability Indication to Mode0.
----End
Example
//Activation Procedure
ADD UCELLHSDPA: CellId=0, HsdpcchPreambleSwitch=Mode1;
MOD UCELLHSDPA: CellId=0, HsdpcchPreambleSwitch=Mode1;
//Deactivation Procedure
ADD UCELLHSDPA: CellId=0, HsdpcchPreambleSwitch=Mode0;
MOD UCELLHSDPA: CellId=0, HsdpcchPreambleSwitch=Mode0;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010630
Streaming Traffic Class on HSDPA.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The configurations of the features on which this feature depends are complete. This
feature depends on the feature WRFD-010611 HSDPA Enhanced Package.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature enables the streaming services to be mapped onto the HS-DSCH, which improves
the utilization of cell resources.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to select MAP_PS_STREAM_ON_HSDPA_SWITCH from
the drop-down list Service mapping strategy switch.
l Verification Procedure
1. Initiate Uu interface tracing on the BSC6900 LMT, as shown in Figure 139-1.
2. Establish an HSDPA streaming service on the UE. To check whether the establishment
is successful, view the RRC_RB_SETUP message and check whether the dl-
TransportChannelType in the rb-MappingInfo information element (IE) is set to
hsdsch in the Uu interface trace data.
3. Check whether the service can receive the data successfully.
l Deactivation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to clear MAP_PS_STREAM_ON_HSDPA_SWITCH from
the drop-down list Service mapping strategy switch.
----End
Example
//Activating Streaming Traffic Class on HSDPA
SET UCORRMALGOSWITCH: MapSwitch=MAP_PS_STREAM_ON_HSDPA_SWITCH-1;
//Deactivating Streaming Traffic Class on HSDPA
SET UCORRMALGOSWITCH: MapSwitch=MAP_PS_STREAM_ON_HSDPA_SWITCH-0;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010651
HSDPA over Iur.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The feature WRFD-010610 HSDPA Introduction Package has been configured before
this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The neighboring RNC supports this feature.
Context
This feature enables HSDPA services to be carried on the Iur interface and provides continuous
HSDPA services for UEs moving between BSC6900s.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command MOD UEXT3GCELL (CME single
configuration: Object Group > UMTS Service Configuration and Maintenance
Management > External Cell Configuration > RNC 3G External Cell; CME batch
modification center: 3.19 Modifying RNC External Cell Parameters in Batches)
to configure the neighboring RNC's cell with HSDSCH and Fractional-Dedicated
Physical Control Channel (F-DPCH). In this step, select the HSDSCH support
indicator and F-DPCH support indicator check boxes under the parameter Cell
Capability Container.
2. Run the BSC6900 MML command MOD UNRNC (CME single configuration: IUR
Configuration Express > Neighbouring RNC > Neighboring RNC; CME batch
modification center: not supported). In this step, set Hsdpa cap ind over IUR for
NRNC to ON.
l Verification Procedure
1. Verify that the feature HSDPA over Iur has been activated by performing the following
operations:
Run the BSC6900 MML command LST UNRNC to query the configuration of
the neighboring RNC.
Run the BSC6900 MML command LST UEXT3GCELL to query the
configuration of the neighboring RNC's cell.
2. Verify that an HSDPA service has been set up by performing the following operations:
Configure the neighboring RNC and its cell with the HSDPA function.
Establish an HSDPA service under the serving RNC.
The serving cell changes to a cell under the neighboring RNC.
If the RNSAP_RL_SETUP_REQ message traced on the Iur interface contains
HSDPA-related information elements, an HSDPA service has been set up
successfully.
l Deactivation Procedure
1. Run the BSC6900 MML command MOD UNRNC (CME single configuration: IUR
Configuration Express > Neighbouring RNC > Neighboring RNC; CME batch
modification center: not supported). In this step, set Hsdpa cap ind over IUR for
NRNC to OFF.
2. Run the BSC6900 MML command MOD UEXT3GCELL (CME single
configuration: Object Group > UMTS Service Configuration and Maintenance
Management > External Cell Configuration > RNC 3G External Cell; CME batch
modification center: 3.19 Modifying RNC External Cell Parameters in Batches).
In this step, deselect the HSDSCH support indicator and F-DPCH support
indicator check boxes under the parameter Cell Capability Container.
----End
Example
//Activating HSDPA over Iur
MOD UEXT3GCELL: NRncId=1, CellId=1,
CellCapContainerFdd=HSDSCH_SUPPORT-1&FDPCH_SUPPORT-1;
MOD UNRNC: NRncId=1, IurHsdpaSuppInd=ON;
//Deactivating HSDPA over Iur
MOD UNRNC: NRncId=1, IurHsdpaSuppInd=OFF;
MOD UEXT3GCELL: NRncId=1, CellId=1,
CellCapContainerFdd=HSDSCH_SUPPORT-0&FDPCH_SUPPORT-0;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010652
SRB over HSDPA.
Prerequisites
l Dependencies on Hardware
Requirement for the BSC6900
This feature does not depend on the hardware.
Requirements for the NodeB
The BTS3812E, BTS3812A, or BTS3812AE is configured with the EBBI, EBOI,
or EDLP board.
The BBU3806 is configured with the EBBC or EBBCd board.
The BBU3900 is configured with the WBBPb, WBBPd or wBBPf board.
l Dependencies on Other Features
The WRFD-010610 HSDPA Introduction Package feature must be configured before
this feature is configured.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others
The UE complies with the specifications of 3GPP Release 6 or higher versions and
supports fractional DPCH (F-DPCH) or E-FDPCH.
Context
Using F-DPCH multiplexing, this feature enables downlink signaling radio bearers (SRBs) of
multiple users to be carried over HSDPA. This helps reduce downlink code resource
consumption and call setup delay.
During radio access bearer (RAB) setup, SRBs can be carried over HSDPA only when all the
downlink services of the UE are carried on the HSDPA channels. During radio resource control
(RRC) connection setup, this feature can be activated by performing the following operations:
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UFRCCHLTYPEPARA (CME single
configuration: UMTS Radio Global Configuration Express > Basic Resource
Control Parameter Configuration > Channel Type Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches) to set Type of
Channel Preferably Carrying Signaling RB to HSDPA
(UL_DCH,DL_HSDSCH) or HSPA(UL_EDCH,DL_HSDSCH).
2. Run the BSC6900 MML command SET UFRCCHLTYPEPARA (CME single
configuration: UMTS Radio Global Configuration Express > Basic Resource
Control Parameter Configuration > Channel Type Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches) to set the phase
at which this feature is activated by means of the Effective Flag of Signaling RB
Channel Type parameter.
NOTE
l If Effective Flag of Signaling RB Channel Type is set to False, this feature is activated during
RAB setup. Recommended Value is False.
l If Effective Flag of Signaling RB Channel Type is set to TRUE, this feature is activated during
RRC connection setup.
3. Run the BSC6900 MML command MOD UCELLALGOSWITCH (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Algorithm Switches; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches) to set the E_F_DPCH is activated by means of the Cell Hspa
Enhanced function switch parameter.
NOTE
2. To verify whether this feature is activated , view the information element (IE) dl-
TransportChannelType and rb-Identity in the RRC_RB SETUP message from the
Uu interface trace data.
If the value of dl-TransportChannelType is hsdsch, as shown in Figure 141-2,
and the value of rb-Identity is less than or equal to 4, as shown in Figure 141-3,
this feature is activated.
l Deactivation Procedure
1. Run the BSC6900 MML command SET UFRCCHLTYPEPARA (CME single
configuration: UMTS Radio Global Configuration Express > Basic Resource
Control Parameter Configuration > Channel Type Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches) to set Type of
Channel Preferably Carrying Signaling RB to HSUPA or DCH.
----End
Example
//Activating SRB over HSDPA
//Setting the type of channel on which SRBs are preferably carried with
SrbChlType set to HSDPA
SET UFRCCHLTYPEPARA: SrbChlType=HSDPA;
//Setting the type of channel on which SRBs are preferably carried with
SrbChlTypeRrcEffectFlag set to False
SET UFRCCHLTYPEPARA: SrbChlTypeRrcEffectFlag=False;
//Setting the type of channel on which SRBs are preferably carried with
SrbChlType set to DCH
SET UFRCCHLTYPEPARA: SrbChlType=DCH;
This section describes how to activate, verify, and deactivate the optional feature WRFD-030010
CQI Adjustment Based on Dynamic BLER Target.
Prerequisites
l Dependencies on Hardware
The BTS3812E and BTS3812AE are configured with the EBBI, EBOI, or EDLP board.
The BBU3806 is configured with the EBBC or EBBCd board.
The BBU3900 is configured with the WBBPb, WBBPd or WBBPf board.
l Dependencies on Other Features
WRFD-010610 HSDPA Introduction Package
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
With this feature, the NodeB can dynamically select the optimum BLER target value based on
the channel quality fluctuation of HSDPA users. The NodeB then adjusts the Channel Quality
Indicator (CQI) accordingly, improving user throughput and cell throughput.
Procedure
l Activation Procedure
1. Run the NodeB MML command SET MACHSPARA (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Radio Layer > Locell Algorithm
Parameters > MAC Parameters > MACHSPARA; CME batch modification center:
3.17 Modifying Physical NodeB Parameters in Batches). In this step, set CQI
Adjust Algorithm Switch of non-Conversational Service to
CQI_ADJ_BY_DYN_BLER(CQI Adjusted by Dynamic BLER).
l Verification Procedure
1. Run the NodeB MML command LST MACHSPARA. In this step, check that CQI
Adjust Algorithm Switch of non-Conversational Service is set to
CQI_ADJ_BY_DYN_BLER.
l Deactivation Procedure
1. Run the NodeB MML command SET MACHSPARA (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Radio Layer > Locell Algorithm
Parameters > MAC Parameters > MACHSPARA; CME batch modification center:
3.17 Modifying Physical NodeB Parameters in Batches). In this step, set CQI
Adjust Algorithm Switch of non-Conversational Service to NO_CQI_ADJ(Not
CQI Adjust Algorithm).
----End
Example
//Activating CQI Adjustment Based on Dynamic BLER Target
SET MACHSPARA: LOCELL=0, CQIADJALGOFNONCON=CQI_ADJ_BY_DYN_BLER;
//Verifying CQI Adjustment Based on Dynamic BLER Target
LST MACHSPARA: LOCELL=0;
//Deactivating CQI Adjustment Based on Dynamic BLER Target
SET MACHSPARA: CQIADJALGOFNONCON=NO_CQI_ADJ;
This chapter describes how to activate, verify, and deactivate the basic feature WRFD-030011
MIMO Prime.
Prerequisites
l Dependencies on Hardware
This feature is supported only by the 40W RRU3801C, RRU3804, RRU3806,
RRU3808, WRFU, RRU3805, WRFUd, RRU3828, RRU3829, RRU3928, RRU3929,
MRFUd, MRFUe, as well as the RRU3908 V1 operating in 850 MHz, 900 MHz, and
1900 MHz.
For RF modules providing only one transmit channel, two such RF modules need to be
interconnected to support this feature.
Two RF units, each with a TX channel, are configured.
The BBU3900 is configured with the WBBPb, WBBPd or WBBPf board.
The BTS3812E/AE does not support this feature.
The DBS3800 does not support this feature.
RRU3908 V2 and MRFU V2 modules support this feature from RAN14.0.0
l Dependencies on Other Features
WRFD-010610 HSDPA Introduction Package
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
l MIMO Prime can increase the capacity of the cell in which MIMO has not been
implemented by 5% to 10%. The increase in the overall cell throughput helps to greatly
improve the experience of users in medium and bad radio conditions. MIMO Prime is
applicable to various services such as HSDPA and 64QAM, whereas it does not have any
special requirement for the capabilities of UEs and will not affect the performance of UEs
that do not support MIMO.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command DEA UCELL (CME single configuration: UMTS
Cell Configuration Express > Cell Basic Information > Cell Basic Information.
Set Validation indication to Deactivated; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches) to deactivate cells.
2. On the NodeB, remove the old local cell and establish a new local cell.
a. Run the NodeB MML command RMV LOCELL (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Radio Layer > xx Sector >
Locell; CME batch modification center: not supported) to remove the local cell
b. Run the NodeB MML command ADD LOCELL (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Radio Layer > xx Sector >
Locell; CME batch modification center: 3.17 Modifying Physical NodeB
Parameters in Batches) to add a local cell. In this step, set Support VAM to
TRUE(TRUE), Two Tx Way to FALSE.
3. Run the NodeB MML command SET MACHSPARA (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Radio Layer > Locell Algorithm
Parameters > MAC Parameters > MACHSPARA; CME batch modification center:
3.17 Modifying Physical NodeB Parameters in Batches). In this step, set MIMO
Prime Switch to OPEN(open).
4. Run the BSC6900 MML command ACT UCELL (CME single configuration: UMTS
Cell Configuration Express > Cell Basic Information > Cell Basic Information.
Set Validation indication to Activated; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches) to activate the cell.
l Verification Procedure
1. Run the NodeB MML command LST LOCELL. In this step, check that Support
VAM is TRUE(TRUE), Two Tx Way is FALSE.
2. Run the NodeB MML command LST MACHSPARA. In this step, check that MIMO
Prime Switch is set to Open.
3. Observe the counters VS.APCPhase0CQI.MEAN and VS.APCCQI.MEAN.
Before this feature is activated, the values of both counters are 0. After this feature is
activated, the values of both counters differ from 0.
l Deactivation Procedure
1. Run the BSC6900 MML command DEA UCELL (CME single configuration: UMTS
Cell Configuration Express > Cell Basic Information > Cell Basic Information.
Set Validation indication to Deactivated; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches) to deactivate cells.
2. On the NodeB, remove the old local cell and establish a new local cell.
a. Run the NodeB MML command RMV LOCELL (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Radio Layer > xx Sector >
Locell; CME batch modification center: not supported) to remove the local cell
b. Run the NodeB MML command ADD LOCELL (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Radio Layer > xx Sector >
Locell; CME batch modification center: 3.17 Modifying Physical NodeB
Parameters in Batches) to add a local cell. In this step, set Support VAM to
FALSE(FALSE).
3. Run the NodeB MML command SET MACHSPARA (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Radio Layer > Locell Algorithm
Parameters > MAC Parameters > MACHSPARA; CME batch modification center:
3.17 Modifying Physical NodeB Parameters in Batches). In this step, set MIMO
Prime Switch to CLOSE(close).
4. Run the BSC6900 MML command ACT UCELL (CME single configuration: UMTS
Cell Configuration Express > Cell Basic Information > Cell Basic Information.
Set Validation indication to Activated; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches) to activate the cell.
----End
Example
//Activating MIMO Prime
//Operations at the BSC6900
//Deactivating a cell
DEA UCELL: CellId=1;
This section describes how to activate, verify, and deactivate the optional feature WRFD-030004
Adaptive Configuration of Typical HSPA Rate.
Prerequisites
l Dependencies on Hardware
The BTS3812E, BTS3812A, and BTS3812AE must be configured with the EBBI,
EBOI, EULP+EDLP, or EULPd+EDLP boards. Downlink services must be established
on the EBBI, EBOI, or EDLP board.
The DBS3800 must be configured with the EBBC or EBBCd board. Downlink services
must be established on the EBBC or EBBCd board.
The 3900 series base stations must be configured with the WBBPb, WBBPd, or WBBPf
board. Downlink services must be established on the WBBPb, WBBPd, or WBBPf
board.
l Dependencies on Other Features
The features WRFD-010610 HSDPA Introduction Package and WRFD-010612
HSUPA Introduction Package have been configured before this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
PS BE services carried on an HSPA channel use typical rate rather than the CN-assigned rate as
the maximum rate, leading to inconsistent between the CN-assigned rate and the actual rate.
This feature enables the users to apply the CN-assigned rate rather than the typical rate when
they are different.
l Precautions
None
l Data Preparation
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to enable this feature. In this step, select the
HSPA_ADPTIVE_RATE_ALGO_SWITCH check box under the parameter PS
Rate Negotiation Switch.
l Verification Procedure
1. Before the feature is activated, the CN assigns a non-typical rate for a PS BE service
to be carried on an HSPA channel. Check the real rate.
The PS BE service is set up successfully on an HSPA channel with a typical rate.
2. After the feature is activated, the CN assigns a non-typical rate for a PS BE service to
be carried on an HSPA channel. Check the real rate.
The PS BE service is set up successfully on an HSPA channel with the assigned rate.
l Deactivation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to disable this feature. In this step, clear the
HSPA_ADPTIVE_RATE_ALGO_SWITCH check box under the parameter PS
Rate Negotiation Switch.
----End
Example
//Activating Adaptive Configuration of Typical HSPA Rate
This section describes how to activate, verify, and deactivate the optional feature WRFD-140221
HSDPA Scheduling Based on UE Location.
Prerequisites
l Dependencies on BSC6900 Hardware
This feature does not depend on the BSC6900 hardware.
l Dependencies on NodeB Hardware
All 3900 series base stations support this feature. To support this feature, the 3900 series
base stations must be configured with the WBBPb, WBBPd or WBBPf board.
All DBS3800 series base stations support this feature. To support this feature, the
DBS3800 series base stations must be configured with the EBBC or EBBCd board.
The BTS3812E/BTS3812A/BTS3812AE supports this feature. To support this feature,
the BTS3812E/BTS3812A/BTS3812AE must be configured with the EBBI, EDLP or
EBOI board.
l Dependencies on Other Features
This feature depends on the following features:
WRFD-010610 HSDPA Introduction Package
WRFD-010611 HSDPA Enhanced Package
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others Prerequisites
As recommended, GBRs have been configured on the RNC for all BE services.
Context
l Developed on the basis of the EPF algorithm, this feature considers UE locations as the
criterion for adjusting HSDPA scheduling weights. This feature gives more scheduling
opportunities to UEs close to the NodeB and increases the cell throughput on the downlink.
l Precautions
With this feature, HSDPA UEs at cell edges have fewer scheduling opportunities and
the cell throughput at cell edges drops. If GBRs are not configured for BE services,
HSDPA UEs at cell edges may have to wait a long time before they can get scheduling
opportunities. As a result, traffic radio bearers (TRBs) are more likely to reset and the
call drop rate increases. The magnitude of this impact depends on factors such as UE
distribution and service distribution in the cell. It is recommended that GBRs be
configured for BE services to ensure network performance.
Procedure
l Activation Procedure
1. Run the NodeB MML commandSET MACHSPARA (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Radio Layer > Locell Algorithm
Parameters > MAC Parameters > MACHSPARA; CME batch modification center:
3.17 Modifying Physical NodeB Parameters in Batches). In this step, set
Scheduling Method to EPF_LOC(Location based EPF) and set Location
Weight.
l Verification Procedure
1. Run the NodeB MML commandLST MACHSPARA. If the command output shows
that the value of Scheduling Method is EPF_LOC(Location based EPF), this
feature has been activated for the cell.
l Deactivation Procedure
1. Run the NodeB MML commandSET MACHSPARA (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Radio Layer > Locell Algorithm
Parameters > MAC Parameters > MACHSPARA; CME batch modification center:
3.17 Modifying Physical NodeB Parameters in Batches). In this step, set
Scheduling Method to a value except EPF_LOC(Location based EPF).
----End
Example
//Activation procedure
SET MACHSPARA: LOCELL=1, SM=EPF_LOC, LOCWEIGHT=1;
//Deactivation procedure
SET MACHSPARA: LOCELL=1, SM=EPF;
This section describes how to activate, verify, and deactivate the optional feature WRFD-140222
Adaptive Adjustment of HSUPA Small Target Retransmissions.
Prerequisites
l Dependencies on Hardware
None
l Dependencies on Other Features
This feature depends on WRFD-010612 HSUPA Introduction Package.
l License
None
Context
l With this feature, the target number of retransmissions can shift between two preset values.
In scenarios where a small target number of retransmissions are desired on the E-DCH, the
larger one between the two preset values is used as the target number of retransmissions.
When the uplink load on the cell is not restricted and the UE rate is above a specific
threshold, the smaller one between the two preset values is used as the target number of
retransmissions. This improves the UE throughput. When the uplink load on the cell is
restricted again and the UE rate falls below another threshold, the larger one between the
two preset values is again used as the target number of retransmissions to raise the uplink
throughput of the cell.
l This feature is only intended for non-DC-HSUPA UEs.
l This feature provides two algorithms for configuring the small target number of
retransmissions: algorithm for selecting an initial small target number of retransmissions
for HSUPA UEs and algorithm for adaptively adjusting the small target number of
retransmissions for HSUPA UEs.
l Precautions
None
l Data Preparation
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) with PC_OLPC_SWITCH under Power Control Switch
selected to enable outer-loop power control.
NOTE
You need to activate outer loop power control before activating the adaptive adjustment of
HSUPA small target retransmissions.
2. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) with
PC_HSUPA_LITRETNUM_INIT_SEL_SWITCH and
PC_HSUPA_LITRETNUM_AUTO_ADJUST_SWITCH under Power Control
Switch selected to activate the algorithm for selecting an initial small target number
of retransmissions for HSUPA UEs.
NOTE
When configuring the parameter Alter Edch Little Target Number of E-DCH PDU
retransfer, the default value for this parameter is recommended. An inappropriate value for
this parameter may lead to decreased cell throughput. For services with a 5.44 Mbit/s MBR
and a 2 ms transmission time interval (TTI), the default value of this parameter is 0.02. For
other services with a 2 ms TTI, the default value of this parameter is 0.01. For services with a
10 ms TTI, the default value of this parameter is 0.1.
l Verification Procedure
1. On the BSC6900 LMT main page, click Monitor. In the Monitor Navigation Tree
pane, choose Monitor > UMTS Monitoring > Connection Performance
Monitoring. The Connection Performance Monitoring dialog box is displayed.
2. In this dialog box, set Monitor Item to OLPC,and then click Submit. Check the
average number of transmissions on the E-DCH. If the following conditions are met,
this feature has been activated.
If there are multiple HSUPA UEs, the uplink load of the cell is limited and the
average number of transmissions on the E-DCH is close to the larger value between
EdchTargetLittleRetransNum and EdchAltTarLittleRetransNum.
If there are multiple HSUPA UEs, the uplink load of the cell is unlimited and the
average number of transmissions on the E-DCH is close to the smaller value
between EdchTargetLittleRetransNum and EdchAltTarLittleRetransNum.
l Deactivation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) with
PC_HSUPA_LITRETNUM_INIT_SEL_SWITCH and
PC_HSUPA_LITRETNUM_AUTO_ADJUST_SWITCH under Power Control
Switch cleared to deactivate the algorithm for selecting an initial small target number
of retransmissions for HSUPA UEs.
----End
Example
//Activating Adaptive Adjustment of HSUPA Small Target Retransmissions
SET UCORRMALGOSWITCH: PcSwitch=PC_OLPC_SWITCH-1;
SET UCORRMALGOSWITCH: PcSwitch=
PC_HSUPA_LITRETNUM_INIT_SEL_SWITCH-1&PC_HSUPA_LITRETNUM_AUTO_ADJUST_SWITC
H-1;
//Deactivating Adaptive Adjustment of HSUPA Small Target Retransmissions
SET UCORRMALGOSWITCH: PcSwitch=
PC_HSUPA_LITRETNUM_INIT_SEL_SWITCH-0&PC_HSUPA_LITRETNUM_AUTO_ADJUST_SWITC
H-0;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010680
HSPA+ Downlink 28Mbps per User.
Prerequisites
l Dependencies on Hardware
BSC6900
This feature does not have any special requirements for hardware.
NodeB
The BTS3812E, BTS3812A, and BTS3812AE should be configured with the EBBI,
EBOI or EDLP board.
The BBU3806 should be configured with the EBBC or EBBCd board.
The BBU3900 should be configured with the WBBPb, WBBPd or WBBPf board.
For the RF part, the RF module of Node B supports one TX channel each, and two
interconnected RF modules can provide two TX channels to support 2 x 2 MIMO.
l Dependencies on Other Features
The configurations of the features on which this feature depends are complete. This
feature depends on the feature:
WRFD-010684 2 x 2 MIMO or WRFD-010696 DC-HSDPA
WRFD-010650 HSDPA 13.976 Mbps per User
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
CN support user rate of 28Mbit/s or above.
The UE category must support cat16, cat18(or later).
Context
This feature enables the theoretical HSPA+ MIMO rate per user to reach a maximum of 28
Mbps. This feature enhances the user experience for high-speed data services.
Procedure
l Activation Procedure
This feature does not need to be activated.
l Verification Procedure
1. Enable a UE in a 2 x 2 MIMO cell to download a 500 MB file from the FTP server.
Then, detect the download transmission rate. At this time, the UE initiates BE services
in the 2 x 2 MIMO cell and the RNC establishes services on the 2 x 2 MIMO.
l Deactivation Procedure
This feature does not need to be deactivated.
----End
Example
None
This section describes how to activate, verify, and deactivate the optional feature WRFD-010681
HSPA+ Downlink 21Mbps per User.
Prerequisites
l Dependencies on Hardware
Dependencies on BSC6900 Hardware
This feature does not depend on the BSC6900 hardware.
Dependencies on NodeB Hardware
The BTS3812E, BTS3812A, and BTS3812AE are configured with the EBBI, EBOI,
or EDLP board.
The BBU3806 is configured with the EBBC or EBBCd board.
The BBU3900 is configured with the WBBPb, WBBPd or WBBPf board.
l Dependencies on Other Features
The following features have been configured before this feature is activated:
WRFD-010683 Downlink 64QAM, WRFD-010685 Downlink Enhanced L2.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The UE category must support cat 14,18,20,24 or 28.
CN support user rate of 21Mbit/s or above.
Context
This feature enables the theoretical HSPA+ 64QAM rate per user to reach a maximum of 21
Mbps. It provides users with high-speed data services.
Procedure
l Activation Procedure
This feature does not need to be activated.
l Verification Procedure
1. Use the UE in a 64QAM cell to download a 500 MB file from the FTP server. Then,
check the downloading rate.
l Deactivation Procedure
This feature does not need to be deactivated.
----End
Example
None
This section describes how to activate, verify, and deactivate the optional feature WRFD-010685
Downlink Enhanced L2.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The feature WRFD-010610 HSDPA Introduction Package must be configured before
this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others
The UE is of 3GPP R7 or later and supports this feature.
Context
The Downlink Enhanced L2 feature eliminates contradictions between high-rate transmission
that requires a large PDU size and cell-edge coverage that requires a small PDU size by using
flexible Protocol Data Unit (PDU) sizes. This feature enables dynamic adjustment of the PDU
size. This improves transmission efficiency on the Iub and Uu interfaces and increases the cell-
edge throughput and coverage radius.
This feature is a prerequisite for the features DL 64QAM, 2x2 MIMO, and Enhanced
CELL_FACH.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UFRC (CME single configuration: UMTS
Radio Global Configuration Express > Basic Resource Control Parameter
Configuration > RNC Oriented FRC Algorithm Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches) to set the RNC-
2. Use the UE to establish an HSDPA service. Check whether the value of the IE dl-
TransportChannelType in the rb-MappingInfo of the RRC_RB_SETUP message
is hsdsch.
3. View the value of the IE dL RLC PDU size in the RRC_RB_SETUP message.
If the value of the IE dL RLC PDU size is flexibleSize, as shown in Figure
149-2, this feature has been activated.
If the value of the IE dL RLC PDU size is fixedSize, this feature is not activated.
l Deactivation Procedure
1. Run the BSC6900 MML command MOD UCELLALGOSWITCH (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Algorithm Switches; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches). In this step, deselect DL_L2ENHANCED(Cell DL
L2ENHANCED Function Switch) from the Cell Hspa Plus function switch drop-
down list box.
----End
Example
//Activating Downlink Enhanced L2
//Enabling the cell-level downlink L2 enhancement
MOD UCELLALGOSWITCH: CellId=1, HspaPlusSwitch=DL_L2ENHANCED-1;
//Deactivating Downlink Enhanced L2
//Disabling the cell-level downlink L2 enhancement
MOD UCELLALGOSWITCH: CellId=1, HspaPlusSwitch=DL_L2ENHANCED-0;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010689
HSPA+ Downlink 42Mbps per User.
Prerequisites
l Dependencies on Hardware
Only BSC6900 supports this feature.
It is recommended that the BSC6900 be configured with the Data Processing Unit
REV:e (DPUe) board to support more peak-rate users.
On the NodeB side:
The BTS3812E, BTS3812A, or BTS3812AE must be configured with the EBBI,
EBOI or EDLP board.
The BBU3806 must be configured with the EBBC or EBBCd board.
BBU3806 is configured with the Enhanced Base Band Card (EBBC) or Enhanced
Base Band Card REV:d (EBBCd) board.
In the case of BTS3812E, BTS3812A, or BTS3812AE, the NodeB Enhanced
HSDPA Supported Baseband Processing and Interface Unit (EBBI) , NodeB
Enhanced HSDPA Supported Baseband Processing and Optical Interface Unit
(EBOI), or NodeB Enhanced Downlink Processing Unit (EDLP) board is
configured. In addition, the uplink service cannot be established on the NodeB
HSDPA supported Baseband processing and Interface Unit (HBBI) or NodeB
HSUPA supported Uplink Processing Unit (HULP) board.
BBU3900 is configured with the WBBPb, WBBPd or WBBPf board.
For the RF part which supports only one TX channel, two interconnected RF
modules can provide two TX channels to support 2 x 2 MIMO. In terms of RF
modules including 2 Tx channels, no additional RF modules is required for
2*2MIMO.
l Dependencies on Other Features
The following features have been configured before this feature is activated:
WRFD-010689 HSPA+ Downlink 21Mbit/s per User plus WRFD-010696 DC-
HSPA plus WRFD-010612 HSUPA Introduction Package, or WRFD-010689 HSPA
+ Downlink 21Mbit/s per User plus WRFD-010680 HSPA+ Downlink 28Mbit/s per
Context
As indicated in 3GPP Release 8, the downlink peak rate per user reaches up to 42 Mbit/s by
using the 2x2 MIMO+64QAM or 64QAM+DC-HSDPA technologies and by using enhanced
functions of the related NEs.
Procedure
l Activation Procedure
1. This feature does not need to be activated.
l Verification Procedure
1. Set the BE service rate of the UE at the Home Location Register (HLR) to 42 Mbit/
s.
2. Enable a UE in an HSDPA cell to download a 500 MB file from the FTP server. Then,
check whether the download transmission rate is 42 Mbit/s. If yes, this feature has
been activated. At this time, the UE initiates BE services in the HSDPA cell and the
BSC6900 establishes services on the HS-DSCH.
3. Start Monitoring DL Throughput and Bandwidth on the BSC6900 LMT, as shown in
Figure 150-1.
The connection performance monitoring result indicates that the BSC6900 assigns a
42.1 Mbit/s bandwidth to the UE, that is, this feature has been activated.
l Deactivation Procedure
1. This feature does not need to be deactivated.
----End
Example
None
This section describes how to activate, verify, and deactivate the optional feature WRFD-010683
Downlink 64QAM.
Prerequisites
l Dependencies on Hardware
The BTS3812E, BTS3812A and BTS3812AE need to configure EBBI board, EBOI
board or EDLP board.
The BBU3806 needs to be configured with the EBBC or EBBCd board.
The BBU3900 needs to be configured with the WBBPb, WBBPd or WBBPf board.
l Dependencies on Other Features
WRFD-010610 HSDPA Introduction Package
WRFD-010685 Downlink Enhanced L2
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The UE category must support 64QAM. That is, the UE must belong to category
13,14,17,18,19,20,23, 24, 27, 28, as specified by the 3GPP protocols.
Context
The 16QAM modulation scheme, which was introduced in 3GPP R5 specifications, provides a
higher peak rate per user and system capacity than Quadrature Phase Shift Keying (QPSK). The
64QAM modulation scheme, which was introduced in 3GPP R7 specifications, provides a higher
peak rate per user and system capacity than the 16QAM modulation scheme.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
l If the switch parameter is set to 64QAM, the network preferentially configures 64QAM
for the UE. Otherwise, the network preferentially configures MIMO for the UE.
l Before commissioning the feature, you need to set the switch parameter to 64QAM. After
the commissioning, you can set the parameter according to the actual network planning.
l For UEs to 3GPP R7 specifications, MIMO and 64QAM cannot be used together.
3. Run the BSC6900 MML command MOD UCELLALGOSWITCH (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Algorithm Switches; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches) to turn on the cell-level 64QAM switch and enhanced
downlink layer 2 function switch. In this step, select 64QAM(Cell 64QAM Function
Switch) and DL_L2ENHANCED(Cell DL L2ENHANCED Function Switch)
from the Cell Hspa Plus function switch list.
4. Optional: Run the BSC6900 MML command MOD UEXT3GCELL (CME single
configuration: Object Group > UMTS Service Configuration and Maintenance
Management > External Cell Configuration > RNC 3G External Cell; CME batch
modification center: 3.19 Modifying RNC External Cell Parameters in Batches)
to set neighboring BSC6900 cell support 64QAM. Set parameter Cell Capability
Container and select HSPAPLUS_DL_64QAM_SUPPORT (downlink 64QAM
support indicator).
NOTE
In a hard handover or soft handover over Iur, when the serving cell is relocated under the DRNC,
this function is enabled so that the serving cell continues to support 64QAM. Otherwise, the
serving cell does not support 64QAM. In this case, the actual physical capabilities of the cell
under DRNC support 64QAM.
l Verification Procedure
1. As Figure 151-1 shows, start Uu interface tracing on the BSC6900 LMT.
2. Establish an HSDPA service on the UE. Check the RRC_RB_SETUP message and
check that the value of the dl-TransportChannelType information element in rb-
MappingInfo is hsdsch.
3. In the Uu interface tracing data, check the value of the dl-64QAM-Configured
information element under dl-HSPDSCH-Information in the RRC_RB_SETUP
message.
If the value of dl-64QAM-Configured is true as Figure 151-2 shows, you can
infer that this feature has been activated.
Otherwise, you can infer that this feature has not been activated.
l Deactivation Procedure
1. Run the BSC6900 MML command MOD UCELLALGOSWITCH (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Algorithm Switches; CME batch modification center: 3.18 Modifying UMTS Cell
Example
//Activation procedure SET UCORRMALGOSWITCH:
CfgSwitch=CFG_HSDPA_64QAM_SWITCH-1;
SET UFRC: MIMOor64QAMSwitch=64QAM, RetryCapability=64QAM-1;
MOD UCELLALGOSWITCH: CellId=1, HspaPlusSwitch=64QAM-1&DL_L2ENHANCED-1;
(Optional)MOD UEXT3GCELL: NRncId=0, CellId=0,
CellCapContainerFdd=HSPAPLUS_DL_64QAM_SUPPORT-1;
//Deactivation procedure MOD UCELLALGOSWITCH: CellId=1,
HspaPlusSwitch=64QAM-0;
(Optional)MOD UEXT3GCELL: NRncId=0, CellId=0,
CellCapContainerFdd=HSPAPLUS_DL_64QAM_SUPPORT-0;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010684
2x2 MIMO. Multiple Input Multiple Output (MIMO) is a multi-antenna technology, which
enables multiple antennas to receive and transmit data. This increases the data transmission rate.
Prerequisites
l Dependencies on Hardware
The BTS3812E, BTS3812A, and BTS3812AE must be configured with the EBBI,
EBOI, or EDLP board.
The BBU3806 must be configured with the EBBC or EBBCd board.
The BBU3900 must be configured with the WBBPb, WBBPd or WBBPf board.
For the RF part, the RF module of NodeB supports one TX channel each and two
interconnected RF modules can provide two TX channels to support 2 x 2 MIMO.
20W RRU3801c can only support MIMO by using together with the same module (20W
RRU3801c).
l Dependencies on Other Features
WRFD-010610 HSDPA Introduction Package
WRFD-010685 Downlink Enhanced L2
WRFD-010629 DL 16QAM Modulation
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The UE is of HSDPA category 15 or higher, that is, category 15, 16, 17, 18, 19, 20, 21,
22, 23, 24, 25, 26, 27, or 28.
Context
CAUTION
Before enabling this feature in an activated cell, you need to:
l Deactivate the cell. This will interrupt services in the cell. Therefore, enable the feature when
the traffic of the cell is light.
l Ensure that there are sufficient baseband resources on the baseband processing board.
Otherwise, this feature cannot be activated.
2x2 MIMO is introduced to HSDPA in 3GPP R7. To support this feature, the NodeB use two
antennas to transmit signals, and UEs use two antennas to receive signals. When 2x2 MIMO is
enabled, the theoretical peak rate of HSDPA users increases from 14 Mbit/s to 28 Mbit/s.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to turn on the BSC6900-level MIMO algorithm switch. In
this step, set Channel Configuration Strategy Switch to
CFG_HSDPA_MIMO_SWITCH.
2. Run the BSC6900 MML command SET UFRC (CME single configuration: UMTS
Radio Global Configuration Express > Basic Resource Control Parameter
Configuration > RNC Oriented FRC Algorithm Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches) to set common
parameters among the fundamental resource configuration (FRC) parameters. In this
step, set Preferred MIMO or 64QAM character to MIMO.
NOTE
l MIMO and 64QAM cannot be enabled together for UEs of 3GPP R7.
l If Preferred MIMO or 64QAM character is set to MIMO, MIMO is preferentially
configured for the UE.
l Before verifying the feature, set Preferred MIMO or 64QAM character to MIMO. After
the verification, set this parameter to a proper value according to the network plan.
3. Run the BSC6900 MML command MOD UCELLALGOSWITCH (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Algorithm Switches; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches) turn on the cell-level MIMO switch and enhanced L2
function switch. In this step, set Cell Hspa Plus function switch to MIMO,
DL_L2ENHANCED(Cell DL L2ENHANCED Function Switch), and
UL_L2ENHANCED(Cell UL L2ENHANCED Function Switch).
4. Run the BSC6900 MML command DEA UCELL (CME single configuration: UMTS
Cell Configuration Express > Cell Basic Information > Cell Basic Information.
Set Validation indication to Deactivated; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches) to deactivate the cell.
5. Configure the related data on the NodeB according to the MIMO hardware
configuration scheme. The following procedure takes the RRU3804 as an example to
describe how to configure data for the change from one RRU3804 to two cascading
RRU3804s.
a. Optional: Run the NodeB MML command ADD RRUCHAIN (CME single
configuration: NodeB Configuration Express > IUB_NodeB > Device Panel
> Right click TOPO > Add RXU Chain; CME batch modification center: not
supported) to create an RRU chain.
b. Run the NodeB MML command ADD RRU (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Device Panel > TOPO > Right click
RXU CHAIN > Add RXU Board; CME batch modification center: not
supported) to add an RRU to the chain.
6. On the NodeB, modify Diversity Mode of the sector and Two Tx Way of the cell.
a. Run the NodeB MML command RMV LOCELL (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Radio Layer > xx Sector >
Locell; CME batch modification center: not supported) to remove the local cell.
b. Run the NodeB MML command RMV SEC (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Radio Layer > Sector; CME batch
modification center: not supported) to remove the sector.
c. Run the NodeB MML command ADD SEC (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Radio Layer > Sector; CME batch
modification center: not supported) to add a sector. In this step, set Diversity
Mode to COMMON_MODE and configure the antenna data based on the
MIMO hardware deployment scheme.
d. Run the NodeB MML command ADD LOCELL (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Radio Layer > xx Sector >
Locell; CME batch modification center: 3.17 Modifying Physical NodeB
Parameters in Batches) to add a local cell. In this step, set Two Tx Way to
TRUE and configure the antenna data based on the MIMO hardware deployment
scheme.
7. Modify the transmit diversity mode of a cell on the BSC6900.
a. Optional: If UPRACH exists, run the BSC6900 MML command RMV
UPRACH (CME single configuration: UMTS Cell Configuration Express >
Channel Configuration > PRACH Basic Information; CME batch
modification center: not supported) to remove the PRACH.
b. Run the BSC6900 MML command ADD UPRACHBASIC (CME single
configuration: UMTS Cell Configuration Express > Channel Configuration
> PRACH Basic Information; CME batch modification center: not supported)
to add PRACH basic information.
c. Run the BSC6900 MML command ADD UPRACHTFC (CME single
configuration: UMTS Cell Configuration Express > Channel Configuration
> TFC of PRACH; CME batch modification center: not supported) to add TFC
of PRACH.
d. Run the BSC6900 MML command ADD UPRACHASC (CME single
configuration: UMTS Cell Configuration Express > Channel Configuration
> PRACH ASC Information; CME batch modification center: not supported)
to add ASC Of PRACH.
e. Run the BSC6900 MML command ADD UPRACHACTOASCMAP (CME
single configuration: UMTS Cell Configuration Express > Channel
Configuration > AC-ASC Mapping Information of PRACH; CME batch
> Dynamic TFS of FACH; CME batch modification center: not supported) to
add the transport format set (TFS) of the FACH.
s. Run the BSC6900 MML command ADD UFACHLOCH (CME single
configuration: UMTS Cell Configuration Express > Channel Configuration
> Logical Channel Mapped to FACH; CME batch modification center: not
supported) to add a logical channel mapped to the FACH.
t. Run the BSC6900 MML command ADD UPCH (CME single configuration:
UMTS Cell Configuration Express > Channel Configuration > PCH; CME
batch modification center: 3.20 Modifying UMTS Channel Parameters in
Batches) to add a PCH.
u. Run the BSC6900 MML command ADD UPCHDYNTFS (CME single
configuration: UMTS Cell Configuration Express > Channel Configuration
> Dynamic TFS of PCH; CME batch modification center: not supported) to add
the transport format set (TFS) of the PCH.
v. Run the BSC6900 MML command ACT USCCPCH (CME single
configuration: UMTS Cell Configuration Express > Channel Configuration
> SCCPCH Basic Information. Set Validation indication to Activated; CME
batch modification center: not supported) to activate the SCCPCH.
w. Run the BSC6900 MML command MOD UCELLSETUP (CME single
configuration: UMTS Cell Configuration Express > Cell Basic Information
> Cell Basic Information; CME batch modification center: 3.18 Modifying
UMTS Cell Parameters in Batches) to set the transmit diversity mode of an
MIMO-enabled cell to STTD.
Set TX Diversity Indication to TRUE.
Set STTD Support Indicator to STTD_Supported.
Set CP1 Support Indicator to CP1_not_Supported.
Set DPCH Tx Diversity Mode for Other User to STTD.
Set DPCH Tx Diversity Mode for MIMO User to STTD.
Set FDPCH Tx Diversity Mode for Other User to STTD.
Set FDPCH Tx Diversity Mode for MIMO User to STTD.
8. Run the BSC6900 MML command ACT UCELL (CME single configuration: UMTS
Cell Configuration Express > Cell Basic Information > Cell Basic Information.
Set Validation indication to Activated; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches) to activate the cell.
9. Run the BSC6900 MML command ACT UCELLMIMO (CME single configuration:
UMTS Cell Configuration Express > Cell Parameters > Cell MIMO status. Set
Cell MIMO state to Activated; CME batch modification center: not supported) to
activate the MIMO-related parameter settings.
l Verification Procedure
1. Start Uu interface tracing on the BSC6900 LMT, as shown in Figure 152-1.
2. Use the UE to establish an HSDPA service. Check whether the value of the information
element (IE) dl-TransportChannelType in the rb-MappingInfo of the
RRC_RB_SETUP message is hsdsch.
3. In the traced Uu interface data, check whether the RRC_RB_SETUP message
contains the IE mimoParameters.
If the RRC_RB_SETUP message contains the IE mimoParameters, as shown in
Figure 152-2, this feature has been activated.
If the RRC_RB_SETUP message does not contain the IE mimoParameters, as
shown in Figure 152-2, this feature is not activated.
l Deactivation Procedure
1. Run the BSC6900 MML command DEA UCELL (CME single configuration: UMTS
Cell Configuration Express > Cell Basic Information > Cell Basic Information.
----End
Example
l NodeB V200R014
//Activation procedure
//Operations on the BSC6900 side
//Turning on the BSC6900-level MIMO algorithm switch
SET UCORRMALGOSWITCH: CfgSwitch=CFG_HSDPA_MIMO_SWITCH-1;
//Setting MIMO as the preferred function
SET UFRC: MIMOor64QAMSwitch=MIMO;
//Enabling the cell-level MIMO and L2 enhancement
MOD UCELLALGOSWITCH: HspaPlusSwitch=MIMO-1&DL_L2ENHANCED-1;
//Deactivating the HSDPA cell
DEA UCELL: CellId=1;
//Activation operation
RMV UPRACH: CellId=1, PhyChId=4;
ADD UPRACHBASIC: CellId=1,
PreambleSignatures=SIGNATURE0-1&SIGNATURE1-1&SIGNATURE2-1&SIGNATURE3-
1&SIGNATURE4-1&SIGNATURE5-1&SIGNATURE6-1&SIGNATURE7-1,
RACHSubChNo=SUBCHANEL0-1&SUBCHANEL1-1&SUBCHANEL2-1&SUBCHANEL3-1&SUBCH
ANEL4-1&SUBCHANEL5-1&SUBCHANEL6-1&SUBCHANEL7-1&SUBCHANEL8-1&SUBCHANEL
9-1&SUBCHANEL10-1&SUBCHANEL11-1, Constantvalue=-20, PowerRampStep=3;
ADD UPRACHTFC: CellId=1, PhyChId=4, CTFC=0, PowerOffsetPpm=-3,
GainFactorBetaC=13, GainFactorBetaD=15;
ADD UPRACHTFC: CellId=1, PhyChId=4, CTFC=1, PowerOffsetPpm=-2,
GainFactorBetaC=10, GainFactorBetaD=15;
ADD UPRACHASC: CellId=1, PhyChId=4, AccessServiceClass=ASC0;
ADD UPRACHASC: CellId=1, PhyChId=4, AccessServiceClass=ASC1;
ADD UPRACHASC: CellId=1, PhyChId=4, AccessServiceClass=ASC2,
PersistScalingFactor=D0.9;
//Activating a cell
ACT UCELL: CellId=1;
//Activating the MIMO-related parameter settings
ACT UCELLMIMO: CellId=1;
//Operations on the NodeB side
ADD RRUCHAIN: RCN=0, TT=CHAIN, BM=COLD, HSN=2, HPN=0;
ADD RRU: CN=0, SRN=60, SN=0, TP=TRUNK, RCN=0, PS=0, RT=MRRU, RS=UO,
ALMPROCSW=OFF;
ADD RRU: CN=0, SRN=61, SN=0, TP=TRUNK, RCN=0, PS=1, RT=MRRU, RS=UO,
ALMPROCSW=OFF;
//Removing a local cell and a sector
RMV LOCELL: LOCELL=1;
RMV SEC: STN=0, SECN=2;
//Adding a sector and setting the transmit diversity mode
ADD SEC: STN=0, SECN=2, SECT=REMOTE_SECTOR, ANTM=2, DIVM=COMMON_MODE,
ANT1SRN=60, ANT1N=R0A, ANT2SRN=61, ANT2N=R0A;
//Adding a local cell and setting 2-way transmit diversity
ADD LOCELL: LOCELL=1, STN=0, SECN=2, SECT=REMOTE_SECTOR, TTW=TRUE,
//Activation operation
RMV UPRACH: CellId=1, PhyChId=4;
ADD UPRACHBASIC: CellId=1,
PreambleSignatures=SIGNATURE0-1&SIGNATURE1-1&SIGNATURE2-1&SIGNATURE3-
1&SIGNATURE4-1&SIGNATURE5-1&SIGNATURE6-1&SIGNATURE7-1,
RACHSubChNo=SUBCHANEL0-1&SUBCHANEL1-1&SUBCHANEL2-1&SUBCHANEL3-1&SUBCH
ANEL4-1&SUBCHANEL5-1&SUBCHANEL6-1&SUBCHANEL7-1&SUBCHANEL8-1&SUBCHANEL
9-1&SUBCHANEL10-1&SUBCHANEL11-1, Constantvalue=-20, PowerRampStep=3;
ADD UPRACHTFC: CellId=1, PhyChId=4, CTFC=0, PowerOffsetPpm=-3,
GainFactorBetaC=13, GainFactorBetaD=15;
ADD UPRACHTFC: CellId=1, PhyChId=4, CTFC=1, PowerOffsetPpm=-2,
GainFactorBetaC=10, GainFactorBetaD=15;
ADD UPRACHASC: CellId=1, PhyChId=4, AccessServiceClass=ASC0;
ADD UPRACHASC: CellId=1, PhyChId=4, AccessServiceClass=ASC1;
ADD UPRACHASC: CellId=1, PhyChId=4, AccessServiceClass=ASC2,
PersistScalingFactor=D0.9;
ADD UPRACHASC: CellId=1, PhyChId=4, AccessServiceClass=ASC3,
PersistScalingFactor=D0.9;
ADD UPRACHASC: CellId=1, PhyChId=4, AccessServiceClass=ASC4,
PersistScalingFactor=D0.9;
ADD UPRACHASC: CellId=1, PhyChId=4, AccessServiceClass=ASC5,
PersistScalingFactor=D0.9;
ADD UPRACHASC: CellId=1, PhyChId=4, AccessServiceClass=ASC6,
PersistScalingFactor=D0.9;
ADD UPRACHASC: CellId=1, PhyChId=4, AccessServiceClass=ASC7,
PersistScalingFactor=D0.9;
ADD UPRACHACTOASCMAP: CellId=1, PhyChId=4;
ADD UPRACHSLOTFORMAT: CellId=1, SlotFormatNum=D4;
ADD URACH: CellId=1, PhyChId=4, TrChId=1;
ADD URACHDYNTFS: CellId=1, RLCSize=168, TFsNumber=D1, TbNumber1=1;
ADD URACHDYNTFS: CellId=1, RLCSize=360, TFsNumber=D1, TbNumber1=1;
ADD UAICH: CellId=1, PRACHPhyChId=4, PhyChId=6, STTDInd=TRUE;
ACT UPRACH: CellId=1, PhyChId=4;
RMV USCCPCH: CellId=1, PhyChId=8;
ADD USCCPCHBASIC: CellId=1, PhyChId=8, ScrambCode=0, STTDInd=TRUE,
SlotFormat=D8, TFCIpresence=EXISTS;
ADD USCCPCHTFC: CellId=1, PhyChId=8, CTFC=0;
//Activating a cell
ACT UCELL: CellId=1;
//Activating the MIMO-related parameter settings
ACT UCELLMIMO: CellId=1;
//Operations on the NodeB side
ADD RRUCHAIN: RCN=0, TT=CHAIN, HSN=0, HPN=0;
ADD RRU: CN=0, SRN=60, TP=TRUNK, RCN=0, PS=0, RT=MRRU, RS=UO,
ALMPROCSW=OFF;
ADD RRU: CN=0, SRN=61, TP=TRUNK, RCN=0, PS=1, RT=MRRU, RS=UO,
ALMPROCSW=OFF;
//Removing a local cell and a sector
RMV LOCELL: LOCELL=1;
RMV SEC: STN=0, SECN=2;
//Adding a sector and setting the transmit diversity mode
ADD SEC: STN=0, SECN=2, SECT=REMOTE_SECTOR, ANTM=2, DIVM=COMMON_MODE,
ANT1SRN=60, ANT1N=R0A, ANT2SRN=61, ANT2N=R0A;
//Adding a sector and setting the transmit diversity mode (assuming
that DBS3800 is used)
ADD LOCELL: LOCELL=1, STN=0, SECN=1, SECT=REMOTE_SECTOR, TTW=TRUE,
SRN1=60, SRN2=61, SN2=0, ANT2N=ANTB, ULFREQ=9630, DLFREQ=10580,
MXPWR=430, HISPM=FALSE, RMTCM=FALSE, VAM=FALSE;
//Deactivation procedure
DEA UCELL: CellId=1;
DEA UCELLMIMO: CellId=1;
RMV UPRACH: CellId=1, PhyChId=4;
RMV USCCPCH: CellId=1, PhyChId=8;
MOD UCELLSETUP: CellId=1, TxDiversityInd=FALSE;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010693
DL 64QAM+MIMO.
Prerequisites
l Dependencies on Hardware
The 3900 series base station supports 64QAM+MIMO when the WBBPb, WBBPd or
WBBPf board is configured.
In the case of the BTS3900, BTS3900A, and DBS3900, the WBBPb1, WBBPb2,
WBBPb3, WBBPb4, or WBBPd1 board needs to be configured.
In the case of the BTS3812E and BTS3812AE, the EBBI or EDLP board needs to be
configured.
Two RRUs (for example RRU3804) with single TX channels, or one RRU (for example
the RRU3805 or RRU3808) with a dual TX channel needs to be configured.
The HBBI and HDLP of the BTS3812E AND BTS3812AE do not support 64QAM
+MIMO. To support 64QAM+MIMO, the EBBI or EDLP must be configured.
The BBU3806 of the DBS3800 does not support 64QAM+MIMO. To support 64QAM
+MIMO, the EBBC or EBBCd board must be configured.
l Dependencies on Other Features
WRFD-010684 22 MIMO
WRFD-010683 Downlink 64 QAM
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The UE is of category 19, 20 as specified by the 3GPP specifications.
Context
In 3GPP Release 8, MIMO and 64QAM can be used in combination to increase the peak
throughput of a single user.
With 64QAM+MIMO, the peak throughput of a single user can reach 42Mbit/s, compared to
28Mbit/s with MIMO or 21Mbit/s with 64QAM only.
NOTE
l The SRB, CS service, IMS signaling, and PS conversational services are not carried on MIMO,
64QAM, or MIMO+64QAM because the data flow is small and the gain is insignificant.
l The PS streaming service, PS interactive service, PS background service, and the combined services
with previous services can be carried on MIMO+64QAM.
Data Planning
Procedure
l Activation Procedure
1. Run the NodeB MML command MOD LOCELL (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Radio Layer > xx Sector > Locell; CME
batch modification center: 3.17 Modifying Physical NodeB Parameters in
Batches) to modify a local cell. In this step, set DL 64QAM MIMO to TRUE.
2. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to turn on the following three BSC6900-level switches: In
this step, select CFG_HSDPA_64QAM_SWITCH,
CFG_HSDPA_MIMO_SWITCH, and
CFG_HSDPA_MIMO_WITH_64QAM_SWITCH from the Channel
Configuration Strategy Switch list.
3. Run the BSC6900 MML command SET UFRC (CME single configuration: UMTS
Radio Global Configuration Express > Basic Resource Control Parameter
Configuration > RNC Oriented FRC Algorithm Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches) to configure
preferential use of 64QAM+MIMO. In this step, select MIMO_64QAM from the
Prefered MIMO_64QAM or DC_HSDPA character list.
4. Optional: If the streaming service needs to use HSDPA, run the BSC6900 MML
command SET UCORRMALGOSWITCH (CME single configuration: UMTS
Radio Global Configuration Express > Connection_Oriented RRM Switch
Configuration > Connection Oriented Algorithm Switches; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches). In this step,
Example
//Activation procedure
//Operations on the NodeB side
MOD LOCELL: LOCELL=1, SECT=REMOTE_SECTOR, DL64QAM_MIMO=TRUE;
//Operations on the BSC6900 side
SET UCORRMALGOSWITCH:
CfgSwitch=CFG_HSDPA_64QAM_SWITCH-1&CFG_HSDPA_MIMO_SWITCH-1&CFG_HSDPA_MIMO
_WITH_64QAM_SWITCH-1;
SET UFRC: MIMO64QAMorDCHSDPASwitch=MIMO_64QAM;
SET UCORRMALGOSWITCH: MapSwitch=MAP_PS_STREAM_ON_HSDPA_SWITCH-1;
SET UFRCCHLTYPEPARA: DlStrThsOnHsdpa=D64, DlBeTraffThsOnHsdpa=D64;
MOD UCELLALGOSWITCH: CellId=1,
HspaPlusSwitch=64QAM-1&MIMO-1&DL_L2ENHANCED-1&64QAM_MIMO-1;
//Verification procedure
//Operations on the NodeB side
LST LOCELL: MODE=LOCALCELL, LOCELL=1;
//Operations on the BSC6900 side
LST UCELLALGOSWITCH:CellId=1;
LST UCORRMALGOSWITCH: LstFormat=VERTICAL;
DSP UCELLCHK:CellId=1;
//Deactivation procedure
//Operations on the BSC6900 side
MOD UCELLALGOSWITCH: CellId=1, HspaPlusSwitch=64QAM_MIMO-0;
SET UCORRMALGOSWITCH: CfgSwitch=CFG_HSDPA_MIMO_WITH_64QAM_SWITCH-0;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010698
HSPA+ Uplink 11.5Mbit/s per User.
Prerequisites
l Dependencies on Hardware
Dependencies on NodeB for uplink 16QAM+E-DPCCH boosting:
The BTS3812E, BTS3812A and BTS3812AE must be configured with the EULPd
board.
The DBS3800 must be configured with the EBBCd board.
The 3900 series base station must be configured with the WBBPd or WBBPf board.
Dependencies on NodeB for DC-HSUPA:
The BTS3812E, BTS3812A and BTS3812AE must be configured with the EULP
or EULPd board.
The DBS3800 must be configured with the EBBC or EBBCd board.
The 3900 series base station must be configured with the WBBPb, WBBPd or
WBBPf board.
l Dependencies on Other Features
For uplink 16QAM+E-DPCCH boosting,
WRFD-010694 UL 16QAM
WRFD-010614 HSUPA Phase 2
WRFD-010697 E-DPCCH Boosting
For DC-HSUPA,
WRFD-140204 DC-HSUPA
WRFD-010614 HSUPA Phase 2
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others
The UE must support E-DPCCH boosting. The UE must be of HSUPA category 7, 8,
or 9.
The CN must support an uplink data rate of 11.5Mbit/s or above.
Context
With the original HSUPA peak rate of 5.74 Mbps, the UE increases its uplink peak rate to 11.5
Mbps by using the technologies introduced in 3GPP Release 7, including 16QAM and E-DPCCH
Boosting.
Procedure
l Activation Procedure
1. To enable the SRB to carry over HSUPA, run the BSC6900 MML command SET
UFRCCHLTYPEPARA (CME single configuration: UMTS Radio Global
Configuration Express > Basic Resource Control Parameter Configuration >
Channel Type Parameters; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) with Type of Channel Preferably Carrying Signaling
RB set to HSUPA(UL_EDCH,DL_DCH).
2. To enable the 2 ms TTI switch, run the BSC6900 MML command SET
UCORRMALGOSWITCH (CME single configuration: UMTS Radio Global
Configuration Express > Connection_Oriented RRM Switch Configuration >
Connection Oriented Algorithm Switches; CME batch modification center: 3.15
Modifying RNC Parameters in Batches) with Service Mapping Strategy Switch
set to MAP_HSUPA_TTI_2MS_SWITCH.
3. To enable the switch for RNC-level UL 16QAM, run the BSC6900 MML command
SET UCORRMALGOSWITCH (CME single configuration: UMTS Radio Global
Configuration Express > Connection_Oriented RRM Switch Configuration >
Connection Oriented Algorithm Switches; CME batch modification center: 3.15
Modifying RNC Parameters in Batches) with Channel Configuration Strategy
Switch set to CFG_HSUPA_16QAM_SWITCH.
4. To enable the algorithm switch for RNC-level E-DPCCH Boosting, run the BSC6900
MML command SET UCORRMALGOSWITCH (CME single configuration:
UMTS Radio Global Configuration Express > Connection_Oriented RRM
Switch Configuration > Connection Oriented Algorithm Switches; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches) with Channel
Configuration Strategy Switch set to CFG_EDPCCH_BOOSTING_SWITCH.
5. To enable the switch for cell-level UL 16QAM, run the BSC6900 MML command
MOD UCELLALGOSWITCH (CME single configuration: UMTS Cell
Configuration Express > Cell Parameters > Cell Algorithm Switches; CME batch
modification center: 3.18 Modifying UMTS Cell Parameters in Batches) with Cell
Hspa Plus function switch set to UL_16QAM(Cell UL 16QAM Function
Switch) .
6. To enable the switch for cell-level UL Layer 2 Improvement, run the BSC6900 MML
command MOD UCELLALGOSWITCH (CME single configuration: UMTS Cell
Configuration Express > Cell Parameters > Cell Algorithm Switches; CME batch
modification center: 3.18 Modifying UMTS Cell Parameters in Batches) with Cell
Hspa Plus function switch set to UL_L2ENHANCED(Cell UL L2ENHANCED
Function Switch).
Example
/* Activating the HSPA+ Uplink 11.5Mbps per User feature*/
This section describes how to activate, verify, and deactivate the optional feature WRFD-010703
HSPA+ Downlink 84 Mbit/s per User.
Prerequisites
l Dependencies on Hardware
Requirements on BSC6900 Hardware
The DPUe is required to support this feature.
The FG2a (for the GE interface), FG2c (for the GE interface), GOUa, or GOUc serve
as the interface boards.
Requirements on NodeB Hardware
The BTS3812AE/BTS3812E and DBS3800 cannot provide the downlink peak rate
of 84 Mbit/s per user.
To support this feature, 3900 series base stations must be configured with the
WBBPd, WBBPb3, WBBPb4 or WBBPf board.
l Dependencies on Other Features
The following features must be configured before this feature is activated:
WRFD-010689 HSPA+ Downlink 42Mbit/s per User
WRFD-010693 DL 64QAM+MIMO
WRFD-010699 DC-HSDPA+MIMO
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others
The UE must be of category 28 to support 84 Mbit/s in the downlink, according to 3GPP
Release 9.
The Iub interface uses IP transmission mode rather than ATM or STM-1 transmission
mode.
Downlink 64QAM
Context
This feature improves the maximum downlink rate of a single user to 84 Mbit/s using 64QAM,
MIMO, and DC-HSDPA, and users can experience high-speed data services.
Procedure
l Activation Procedure
This feature does not need to be activated.
l Verification Procedure
1. Set the BE service rate of a UE at the Home Location Register (HLR) to 84 Mbit/s.
2. Enable the UE in an HSDPA cell to download a 1024 MB file from the FTP server.
Check whether the download transmission rate is close to 84 Mbit/s. If yes, this feature
has been activated. In this case, the UE will originate BE services in the HSDPA cell,
and the BSC6900 will establish services on the HS-DSCH.
3. On the BSC6900 LMT, start Monitoring DL Throughput and Bandwidth, as shown
in Figure 155-1.
The connection performance monitoring result indicates that the bandwidth the
BSC6900 assigns to the UE is close to 84 Mbit/s bandwidth to the UE. That is, this
feature has been activated.
l Deactivation Procedure
This feature does not need to be deactivated.
----End
Example
None
This section describes how to activate, verify, and deactivate the optional feature WRFD-010699
DC-HSDPA+MIMO.
Prerequisites
l Dependencies on Hardware
The HBBI and HDLP boards in the BTS3812E/BTS3812AE do not support the DC-
HSDPA+MIMO feature. To support this feature, the BTS3812E/BTS3812AE must be
configured with the EBBI and EDLP boards.
To support DC-HSDPA+MIMO, the DBS3800 must be configured with the EBBC or
EBBCd boards. In addition, the maximum capability of the DBS3800 is DC+MIMOx1.
That is, only one frequency in a dual cell (DC) group can be configured with MIMO.
3900 series base stations must be configured with the WBBPb, WBBPd or WBBPf
boards.
l Dependencies on Other Features
The following features must be configured before this feature is activated:
WRFD-010696 DC-HSDPA and WRFD-010684 22 MIMO.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others
This feature is dependent on the UE capability (class 25, 26, 27, and 28 on the HS-
DSCH).
Differentiated Service Management.
Context
Introduced in the R9 protocol, the DC-HSDPA+MIMO feature combines the DS-HSDPA
feature in the R8 protocol and the MIMO feature in the R7 protocol. This feature allows two
inter-frequency co-coverage neighboring carriers under a NodeB that use the same frequency
band to simultaneously transmit HSDPA data to a UE.
Procedure
l Activation Procedure
1. To enable the algorithm switch for RNC-level DC-HSDPA+MIMO, run the BSC6900
MML command SET UCORRMALGOSWITCH (CME single configuration:
UMTS Radio Global Configuration Express > Connection_Oriented RRM
Switch Configuration > Connection Oriented Algorithm Switches; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches) with Channel
Configuration Strategy Switch set to CFG_HSDPA_DCMIMO_SWITCH and
CFG_HSDPA_MIMO_SWITCH.
2. Optional: if HSDPA is required for streaming services, you need to enable the
algorithm switch for streaming services carried over HSDPA: run the BSC6900 MML
command SET UCORRMALGOSWITCH (CME single configuration: UMTS
Radio Global Configuration Express > Connection_Oriented RRM Switch
Configuration > Connection Oriented Algorithm Switches; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches) with Service
Mapping Strategy Switch set to MAP_PS_STREAM_ON_HSDPA_SWITCH.
3. Run the BSC6900 MML command SET UFRC (CME single configuration: UMTS
Radio Global Configuration Express > Basic Resource Control Parameter
Configuration > RNC Oriented FRC Algorithm Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches) with HSPA
Technologies Retried by UEs set to DCMIMO_HSDPA.
4. To set the HSDPA threshold for downlink streaming services and for downlink BE
services, run the BSC6900 MML command SET UFRCCHLTYPEPARA (CME
single configuration: UMTS Radio Global Configuration Express > Basic
Resource Control Parameter Configuration > Channel Type Parameters; CME
batch modification center: 3.15 Modifying RNC Parameters in Batches) with DL
streaming traffic threshold on HSDPA and DL BE traffic threshold on HSDPA
set to appropriate values according to the network plan.
5. To enable the switch for cell-level DC-HSDPA+MIMO and the algorithm switch for
DL Layer2 Improvement, run the BSC6900 MML command MOD
UCELLALGOSWITCH (CME single configuration: UMTS Cell Configuration
Express > Cell Parameters > Cell Algorithm Switches; CME batch modification
center: 3.18 Modifying UMTS Cell Parameters in Batches) with Cell Hspa Plus
function switch set to DL_L2ENHANCED and DCMIMO_HSDPA.
NOTE
You are advised to enable the switch for cell-level DC-HSDPA+MIMO and the algorithm
switch for DL Layer2 Improvement on two cells of the DC-HSDPA cell group.
6. To add the HSDPA parameters for a cell, run the BSC6900 MML command ADD
UCELLHSDPA (CME single configuration: UMTS Cell Configuration Express >
Cell Parameters > Cell HSDPA Parameters; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches) with related parameters set to
appropriate values according to the network plan.
7. To enable the switch for cell-level DC-HSDPA+MIMO, run the NodeB MML
command ADD LOCELL (CME single configuration: NodeB Configuration
Express > IUB_NodeB > Radio Layer > xx Sector > Locell; CME batch
modification center: 3.17 Modifying Physical NodeB Parameters in Batches) or
MOD LOCELL (CME single configuration: NodeB Configuration Express >
IUB_NodeB > Radio Layer > xx Sector > Locell; CME batch modification center:
3.17 Modifying Physical NodeB Parameters in Batches) with DC+MIMO set to
TRUE on the NodeB.
l Deactivation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, deselect
CFG_HSDPA_DCMIMO_SWITCH and CFG_HSDPA_MIMO_SWITCH from
the Channel Configuration Strategy Switch drop-down list to disable the algorithm
switch for RNC-level DC-HSDPA+MIMO on the RNC.
2. Run the BSC6900 MML command MOD UCELLALGOSWITCH (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Algorithm Switches; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches). In this step, deselect DCMIMO_HSDPA(Cell DC-
HSDPA Combined with MIMO Function Switch) from the Cell Hspa Plus
function switch drop-down list to disable the algorithm switch for cell-level DC-
HSDPA+MIMO on the RNC.
3. Run the NodeB MML command MOD LOCELL (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Radio Layer > xx Sector > Locell; CME
batch modification center: 3.17 Modifying Physical NodeB Parameters in
Batches). In this step, set DC+MIMO to FALSE to disable the algorithm switch for
DC-HSDPA+MIMO on the NodeB.
----End
Example
/*Activating DC-HSDPA+MIMO*/
//Enabling the algorithm switch for RNC-level DC-HSDPA+MIMO
SET UCORRMALGOSWITCH:
CfgSwitch=CFG_HSDPA_DCMIMO_SWITCH-1&CFG_HSDPA_MIMO_SWITCH-1;
//(Optional) Enabling the algorithm switch for streaming services over
HSDPA If HSDPA is required for streaming services
SET UCORRMALGOSWITCH: MapSwitch=MAP_PS_STREAM_ON_HSDPA_SWITCH-1;
//Enabling the retried switch for DC-HSDPA+MIMO
SET UFRC: RetryCapability=DCMIMO_HSDPA-1;
//Setting HSDPA thresholds for downlink streaming services and for
downlink BE services
SET UFRCCHLTYPEPARA: DlStrThsOnHsdpa=D64, DlBeTraffThsOnHsdpa=D64;
//Enabling the switch for cell-level DC-HSDPA+MIMO and the algorithm
switch for DL Layer2 Improvement
MOD UCELLALGOSWITCH: CellId=1,
HspaPlusSwitch=64QAM-1&MIMO-1&DL_L2ENHANCED-1&64QAM_MIMO-1&DC_HSDPA-1&DCM
IMO_HADPA-1
//Adding the HSDPA parameters for a cell
ADD UCELLHSDPA: CellId=1, AllocCodeMode=Automatic,
CodeAdjForHsdpaSwitch=ON;
/*Deactivating DC-HSDPA+MIMO*/
//Disabling the algorithm switch for RNC-level DC-HSDPA+MIMO
SET UCORRMALGOSWITCH: CfgSwitch=CFG_HSDPA_DCMIMO_SWITCH-0;
//Disable the switch for cell-level DC-HSDPA+MIMO
MOD UCELLALGOSWITCH: CellId=1, HspaPlusSwitch=DCMIMO_HSDPA-0;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010694
UL 16QAM.
Prerequisites
l Dependencies on Hardware
In the case of the 3900 series base station, the WBBPd or WBBPf board needs to be
configured.
In the case of the DBS3800, the EBBCd board needs to be configured.
In the case of the BTS3812E/BTS3812AE, the EULPd board needs to be configured.
For the BTS3812E/BTS3812AE, the uplink resource groups are set up on the EULPd
board, and the downlink cells are set up on the EBBI or EDLP board.
l Dependencies on Other Features
WRFD-010614 HSUPA Phase 2
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The CN supports the "peak rate per user" introduced by UL 16QAM.
The UE must be of category 7, category 9.
Context
l This feature can help increase the system capacity in the uplink so that HSUPA users can
obtain a higher peak rate.
l It is recommended that the feature WRFD-010692 HSUPA FDE be activated to help
increase the data throughput on the Uu interface.
Procedure
l Activation Procedure
1. Run the NodeB MML command MOD LOCELL (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Radio Layer > xx Sector > Locell; CME
3. Use the UE to perform a dialing test of the PS service. Ensure that an HSUPA service
is established.
4. Analyze the trace messages. In the Uu interface trace data, view the EDCH
information information element (IE) in the RRC_RB_SETUP message.
As shown in Figure 157-2, if the EDCH information IE contains the indicator of
uplink 16QAM, you can infer that this feature has been activated.
If the EDCH information IE does not contain the indicator of uplink 16QAM,
you can infer that this feature has not been activated.
l Deactivation Procedure
1. Run the NodeB MML command MOD LOCELL (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Radio Layer > xx Sector > Locell; CME
batch modification center: 3.17 Modifying Physical NodeB Parameters in
Batches) to modify the local cell. In this step, set UL_16QAM to FALSE.
2. Run the BSC6900 MML command MOD UCELLALGOSWITCH (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Algorithm Switches; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches), Clear the UL_16QAM(Cell UL 16QAM Function
Switch) check box under the parameter Cell Hspa Plus function switch.
3. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches), Clear the CFG_HSUPA_16QAM_SWITCH check box
under the parameter Channel Configuration Strategy Switch.
----End
Example
//Activation procedure
MOD LOCELL: LOCELL=1, UL_16QAM=TRUE;
ADD UCELLALGOSWITCH: CellId=1, HspaPlusSwitch=UL_16QAM-1;
SET UCORRMALGOSWITCH: CfgSwitch=CFG_HSUPA_16QAM_SWITCH-1;
//Verification procedure
DSP LOCELL: LOCELL=1;
//Deactivation procedure
MOD LOCELL: LOCELL=1, UL_16QAM=FALSE;
MOD UCELLALGOSWITCH: CellId=1, HspaPlusSwitch=UL_16QAM-0;
SET UCORRMALGOSWITCH: CfgSwitch=CFG_HSUPA_16QAM_SWITCH-0;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010695
UL Layer 2 Improvement.
Prerequisites
l Dependencies on Hardware
In the case of the BTS3900, BTS3900A, or DBS3900, the WCDMA Baseband Process
Unit REV:b (WBBPb) board (including WBBPb1, WBBPb2, WBBPb3, and WBBPb4)
or the WCDMA Baseband Process Unit REV:d (WBBPd) board (including WBBPd1
or WBBPd2) is configured.
For BBU3806,EBBC or EBBCd is needed.
For BBU3900, WBBPb ,WBBPd or WBBPf is needed.
For BTS3812E and BTS3812AE, EBBI/EBOI/EULP/EULPd is needed.
l Dependencies on Other Features
The WRFD-010612 HSUPA Introduction Package feature has been configured before
this feature is activated.
WRFD-010685 Downlink Enhanced L2
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The UE needs to be compliant with 3GPP Release 8 (or later) to support the feature.
Context
This feature enables the radio link layer to use a flexible Protocol Data Unit (PDU) size for data
transmission based on the radio transmission environment on the Uu interface.
l When the UE is located at the cell edge, data is transmitted in a small PDU size, reducing
the bit error rate (BER) caused by power limitation and improving the data transmission
efficiency.
l When the UE is located in the cell center, data is transmitted in a large PDU size, meeting
the high-speed data transmission requirement and increasing the data transmission
efficiency. As a result, the effective throughput of the entire system is increased.
Procedure
l Activation Procedure
1. Optional: Run the BSC6900 MML command SET UFRC (CME single
configuration: UMTS Radio Global Configuration Express > Basic Resource
Control Parameter Configuration > RNC Oriented FRC Algorithm
Parameters; CME batch modification center: 3.15 Modifying RNC Parameters in
Batches) to set parameters related to UL Layer 2 Improvement at the BSC6900 level.
In this step, set Cell_DCH UL L2 enhance max RLC PDU size and Cell_DCH UL
L2 enhance min RLC PDU size to appropriate values.
NOTE
Generally, use the default values of Cell_DCH UL L2 enhance max RLC PDU size and
Cell_DCH UL L2 enhance min RLC PDU size of the BSC6900.
2. Run the BSC6900 MML command MOD UCELLALGOSWITCH (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Algorithm Switches; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches) to enable UL Layer 2 Improvement at the cell level. In this
step, select the DL_L2ENHANCED(Cell DL L2ENHANCED Function Switch)
check box under the parameter Cell Hspa Plus function switch.
3. NodeB V100R014: Run the NodeB MML command MOD LOCELL (CME single
configuration: NodeB Configuration Express > IUB_NodeB > Radio Layer > xx
Sector > Locell; CME batch modification center: 3.17 Modifying Physical NodeB
Parameters in Batches) to enable UL Layer 2 Improvement at the cell level. In this
step, set UL_L2+ to TRUE.
4. NodeB V200R014: Run the NodeB MML command MOD LOCELL (CME single
configuration: NodeB Configuration Express > IUB_NodeB > Radio Layer > xx
Sector > Locell; CME batch modification center: 3.17 Modifying Physical NodeB
Parameters in Batches) to enable UL Layer 2 Improvement at the cell level. In this
step, set UL L2 Enhanced to TRUE.
l Verification Procedure
1. Start Uu interface tracing on the BSC6900 LMT, as shown in Figure 158-1.
The type of services that use this feature is limited by the HSUPA rate threshold.
3. In the Uu interface tracing data, check the value of the information element (IE) rlc-
PDU-Size in the RRC_RB_SETUP message.
If the value of the IE rlc-PDU-Size is flexibleSize, as shown in Figure 158-2, this
feature has been activated.
If the value of the IE rlc-PDU-Size is fixedSize, this feature is not activated.
l Deactivation Procedure
Example
//Activation procedure
//Turning on the cell-level switch for UL Layer 2 Improvement on the
BSC6900 side
MOD UCELLALGOSWITCH: CellId=1, HspaPlusSwitch=UL_L2ENHANCED-1;
//Enabling UL Layer 2 Improvement at the cell level on the NodeB side
//NodeB V100R014
MOD LOCELL: CellId=1, UL_L2+=TRUE;
//NodeB V200R014
MOD LOCELL: CellId=1, UL_L2PLUS=TRUE;
//Deactivation procedure
//Turning off the cell-level switch for UL Layer 2 Improvement on the
BSC6900 side
MOD UCELLALGOSWITCH: HspaPlusSwitch=UL_L2ENHANCED-0;
//Disabling UL Layer 2 Improvement at the cell level on the NodeB side//
NodeB V100R014
MOD LOCELL: CellId=1, UL_L2+=FALSE;
//NodeB V200R014
MOD LOCELL: CellId=1, UL_L2PLUS=FALSE;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010696
DC-HSDPA.
Prerequisites
l Dependencies on Hardware
For 3900 series base station, BBU3900 needs to be configured with the WBBPb,
WBBPd or WBBPf.
For DBS3800 base station, the BBU3806 needs to be configured with the EBBC or
EBBCd.
The BTS3812E or BTS3812AE needs to be configured with the EBBI or EDLP board,
and the UL baseband resources of DC-HSDPA cells cannot be carried on the HBBI or
HULP board. They can be carried on the EBBI or EDLP board.
For the BSC6900, DPUe boards are recommended because the downlink 42 Mbit/s
throughput of DC-HSDPA users may be affected if the BSC6900 is configured with
DPUb boards.
l Dependencies on Other Features
WRFD-010610 HSDPA Introduction Package
WRFD-010629 DL 16QAM Modulation
WRFD-010685 Downlink Enhanced L2
l License
The license controlling this feature has been activated.
l Other Prerequisites
The UEs must belong in categories 21 or later(category 21, 22, 23, 24, 25, 26, 27, 28),
as specified by the 3GPP specifications.
Context
CAUTION
Activate this feature when the traffic volume in a cell is low. The reason is that the cell must be
deactivated before this feature is activated; after the cell is deactivated, the services in this cell
are disrupted.
NOTE
l The CS service, IMS signaling, SRB signaling, or PS conversational service is carried on a single carrier
instead of DC-HSDPA because the amount of data is small and the gain is insignificant when DC-
HSDPA is used.
l The BE or streaming service can be carried over the DC-HSDPA. The BE/streaming combined service
is carried over the DC-HSDPA preferentially.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command MOD UNODEB (CME single configuration:
NodeB Configuration Express > IUB_RNC > NodeB Basic Information >
NodeB; CME batch modification center: not supported). In this step, set NodeB
Protocol Version to R9.
2. Run the BSC6900 MML command MOD UCNNODE (CME single configuration:
UMTS Global Configuration Express > Core Network > UMTS CN Node; CME
batch modification center: not supported). In this step, set CN protocol version to
R8.
3. Run the BSC6900 MML command DEA UCELL (CME single configuration: UMTS
Cell Configuration Express > Cell Basic Information > Cell Basic Information.
Set Validation indication to Deactivated; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches) to deactivate the logical cell of local
cell 1.
4. Run the BSC6900 MML command DEA UCELL (CME single configuration: UMTS
Cell Configuration Express > Cell Basic Information > Cell Basic Information.
2. For cells with Cell DC-HSDPA Function Switch turned on, trace
RRC_RB_SETUP messages on the Uu interface.
3. Perform dialing tests on FTP services for a UE to ensure that data is transmitted on
HSDPA channels.
4. On the Trace tab page of the LMT, check whether RRC_RB_SETUP messages
contain the dl-SecondaryCellInfoFDD information element.
If the dl-SecondaryCellInfoFDD information element is contained, as shown in
Figure 159-2, it indicates that the feature is activated.
If the dl-SecondaryCellInfoFDD information element is not contained, it
indicates that the feature is not activated.
l Deactivation Procedure
To remove a DC-HSDPA cell group, you only need to remove one local cell in the group.
4. Run the BSC6900 MML command ACT UCELL (CME single configuration: UMTS
Cell Configuration Express > Cell Basic Information > Cell Basic Information.
Set Validation indication to Activated; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches) to activate the logical cell of local
cell 1.
----End
Example
//Activation procedure
//Modify the protocol version of the NodeB and CN
MOD UNODEB: IDTYPE=BYID, NodeBId=0, NodeBProtclVer=R9;
MOD UCNNODE: CnOpIndex=0, CNId=0, CNDomainId=PS_DOMAIN, CNProtclVer=R8;
//To deactivate cells, run the following command repeatedly:
DEA UCELL: CellId=1;
DEA UCELL: CellId=2;
//Setting channel configuration strategy switch
SET UCORRMALGOSWITCH: CfgSwitch=CFG_HSDPA_DC_SWITCH-1;
//Setting preferred MIMO_64QAM or DC_HSDPA character
SET UFRC: MIMO64QAMorDcHSDPASwitch= DC_HSDPA;
//Setting Cell Hspa Plus function switch
MOD UCELLALGOSWITCH: CellId=1, HspaPlusSwitch=DC_HSDPA-1;
MOD UCELLALGOSWITCH: CellId=2, HspaPlusSwitch=DC_HSDPA-1;
//Querying the parameter Time Offset (TCELL) of the cell
LST UCELL: LstType=ByCellId, CellId=1;
LST UCELL: LstType=ByCellId, CellId=2;
//Modifying the time offset of the cell
MOD UCELLSETUP: CellId=2, TCell=CHIP512;
//Configuring local cell 1 and local cell 2 as a DC-HSDPA cell group
ADD DLDUALCELLGRP: FIRSTLOCELL=1, SECONDLOCELL=2;
//Activating the cells
ACT UCELL: CellId=1;
ACT UCELL: CellId=2;
//Deactivation procedure
//To set Channel Configuration Strategy Switch, run the following
command:
MOD UCELLALGOSWITCH: CellId=1, HspaPlusSwitch=DC_HSDPA-0;
MOD UCELLALGOSWITCH: CellId=2, HspaPlusSwitch=DC_HSDPA-0;
//To deactivate cell, run the following command:
DEA UCELL: CellId=1;
This section describes how to activate, verify, and deactivate the optional feature WRFD-140203
HSPA+ Uplink 23 Mbit/s per User.
Prerequisites
l Dependencies on Hardware
This feature has the following impact on the RNC hardware:
The DPUb or DPUe board must be configured.
In IP transmission mode, the GOUa, FG2A, POUc, FG2c or GOUc board must be
configured. The following table briefly describes the boards:
The BTS3812E, BTS3812A and BTS3812AE support this feature. The EULPd
board must be configured on these base stations. Downlink services must be
established on the EBBI, EBOI or EDLP board.
When 4-way receive diversity is used, only 3900 series base stations (except the
BTS3902E) support this feature.
The uplink peak rate of 23 Mbit/s is applicable only to IP transmission scenarios.
The NodeB connects to the transmission equipment through the Ethernet port on the
transmission board.
The UE must support E-DPCCH Boosting and DC-HUSPA. The UE must be of
HSUPA UE category.
The CN is of 3GPP Release 7 or later to support a maximum uplink rate of 23 Mbit/
s or higher, which is promised at service subscription time.
l Dependencies on Other Features
The following features have been configured before this feature is activated:
WRFD-010694 UL 16QAM
WRFD-010697 E-DPCCH Boosting
WRFD-140204 DC-HSUPA
WRFD-010698 HSPA+ Uplink 11.5Mbit/s per User
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
To support a peak rate of 23 Mbit/s of a single UE, the IP over Iub transmission is used
and the uplink bandwidth is greater than 25 Mbit/s.
On the NodeB side, run the SET ETHPORT or ADD ETHPORT command to set
Maximum Transmission Unit to 1500 or above. The default value of this parameter
is 1500.
The transmission network carried on the Iub interface supports the maximum
transmission unit (MTU) of greater than 1500 bytes. On the NodeB, the ping operation
is performed, with PING Packet Size set to 2990. If the ping operation succeeds, the
transmission network meets the requirements.
The UE must support E-DPCCH Boosting and DC-HUSPA.The UE must be of HSUPA
UE category 9.
The CN is of 3GPP Release 7 or later to support a maximum uplink rate of 23 Mbit/s
or higher, which is promised at service subscription time.
Procedure
l Activation Procedure
After the license is activated, this feature has been activated.
l Verification Procedure
1. Enable a DC-HSUPA UE supporting 16QAM to access the network and to establish
PS services on the E-DCH and HS-DSCH.
2. On the BSC6900 LMT, start Monitoring UL Throughput and Bandwidth, as shown
in Figure 160-1.
Expected result: The bandwidth is 23 Mbit/s, and FTP uploading is normal. The feature
has been activated.
l Deactivation Procedure
None
----End
This section describes how to activate, verify, and deactivate the optional feature WRFD-140204
DC-HSUPA.
Prerequisites
l Dependencies on Hardware
This feature has the following impact on the NodeB hardware:
All 3900 series base stations support this feature. The WBBPd or WBBPf board
must be configured on these base stations.
All DBS3800 series base stations support this feature. The EBBCd board must be
configured on these base stations.
The BTS3812E, BTS3812A and BTS3812AE configured with the EBBI, EBOI,
EULP, or EULPd board support this feature. Downlink services must be established
on the EBBI, EBOI or EDLP board.
When 4-way receive diversity is used, only 3900 series base stations (except the
BTS3902E) support this feature.
The uplink peak rate of 23 Mbit/s is applicable only to IP transmission scenarios.
The NodeB connects to the transmission equipment through the Ethernet port on the
transmission board. In addition to the DPUb or DPUe board, the GOUa, FG2a,
POUc, FG2c, or GOUc board must be configured on the RNC.
l Dependencies on Other Features
The following features have been configured before this feature is activated:
WRFD-010614 HSUPA Phase 2
WRFD-010695 UL Layer 2 Improvement
WRFD-010652 SRB over HSDPA
WRFD-010636 SRB over HSUPA
WRFD-010696 DC-HSDPA
WRFD-010638 Dynamic CE Resource Management
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
To support a peak rate of 11.5 Mbit/s of a single UE, the license for the feature
WRFD-010698 HSPA+ Uplink 11.5 Mbit/s per User must be activated.
To support a peak rate of 23 Mbit/s of a single UE, the license for the feature
WRFD-140203 HSPA+ Uplink 23 Mbit/s per User must be activated.
l Other Prerequisites
Two DC-HSUPA cells must be on intra-band adjacent carriers that provide the same
coverage.
Two adjacent carriers are available and DC-HSDPA has been configured in the
downlink.
To support a peak rate of 23 Mbit/s of a single UE, the IP over Iub transmission is used
and the uplink bandwidth is greater than 25 Mbit/s.
On the NodeB side, run the SET ETHPORT or ADD ETHPORT command to set
Maximum Transmission Unit to 1500. The default value of this parameter is 1500.
The UE must comply with 3GPP Release 9 or later.
The UE must be of HSUPA UE category 8 or 9.
Category-8 UEs support only DC-HSUPA+QPSK. Their peak rate is 11.5 Mbit/s.
Category-9 UEs support DC-HSUPA+16QAM. Their peak rate is 23 Mbit/s.
Context
Before DC-HSUPA is configured, DC-HSDPA must be configured in cells. For details, see 159
Configuring DC-HSDPA.
Procedure
l Activation Procedure
1. Run the NodeB MML command ADD ULDUALCELLGRP (CME single
configuration: NodeB Configuration Express > IUB_NodeB > Basic
Information > Radio Management > Other Information >
ULDUALCELLGRP; CME batch modification center: not supported) to configure
cells in a DC-HSUPA carrier group.
2. To enable the DC-HSUPA algorithm on the RNC, Run the BSC6900 MML
command SET UCORRMALGOSWITCH (CME single configuration: UMTS
Radio Global Configuration Express > Connection_Oriented RRM Switch
Configuration > Connection Oriented Algorithm Switches; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches). In this step,
select CFG_HSUPA_DC_SWITCH under Channel Configuration Strategy
Switch.
3. To configure the cell capability on the RNC, Run the BSC6900 MML command MOD
UCELLALGOSWITCH (CME single configuration: UMTS Cell Configuration
Express > Cell Parameters > Cell Algorithm Switches; CME batch modification
center: 3.18 Modifying UMTS Cell Parameters in Batches). In this step, select
DC_HSUPA(Cell DC-HSUPA Function Switch) under Cell Hspa Plus function
switch.
NOTE
DC-HSUPA must be enabled for the two cells. Logical cells corresponding to the local cells
on the NodeB must be configured.
4. To configure DC-HSUPA periodic retry capability, Run the BSC6900 MML
command SET UFRC (CME single configuration: UMTS Radio Global
2. Perform dialing tests on FTP services for a DC-HSUPA UE and ensure that HSUPA
services have been set up.
3. On the Trace tab page of the BSC6900 LMT, check whether the
RRC_RB_SETUP messages contain the ul-SecondaryCellInfoFDD information
element (IE). If the IE is contained, the DC-HSUPA feature has been activated, as
shown in Figure 161-2.
l Deactivation Procedure
NOTE
Deactivating the DC-HSUPA feature decreases cell uplink throughput.
1. Disable the DC-HSUPA algorithm on the RNC.
To disable the DC-HSUPA feature of the entire RNC, Run the BSC6900 MML
command SET UCORRMALGOSWITCH (CME single configuration: UMTS
Radio Global Configuration Express > Connection_Oriented RRM Switch
Configuration > Connection Oriented Algorithm Switches; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches). In this step,
clear CFG_HSUPA_DC_SWITCH under Channel Configuration Strategy
Switch.
To disable the DC-HSUPA feature of a specified cell, Run the BSC6900 MML
command MOD UCELLALGOSWITCH (CME single configuration: UMTS
Cell Configuration Express > Cell Parameters > Cell Algorithm Switches;
CME batch modification center: 3.18 Modifying UMTS Cell Parameters in
Batches). In this step, clear DC_HSUPA(Cell DC-HSUPA Function Switch)
under Cell Hspa Plus function switch.
2. Optional: Run the NodeB MML command RMV ULDUALCELLGRP (CME
single configuration: NodeB Configuration Express > IUB_NodeB > Basic
Information > Radio Management > Other Information >
ULDUALCELLGRP; CME batch modification center: not supported) to remove a
carrier group.
----End
Example
//Activation procedure
ADD ULDUALCELLGRP: FIRSTLOCELL=0, SECONDLOCELL=2;
SET UCORRMALGOSWITCH: CfgSwitch=CFG_HSUPA_DC_SWITCH-1;
MOD UCELLALGOSWITCH: CellId=1, HspaPlusSwitch=DC_HSUPA-1;
MOD UCELLALGOSWITCH: CellId=2, HspaPlusSwitch=DC_HSUPA-1;
SET UFRC: RetryCapability=DC_HSUPA-1;
SET UFRCCHLTYPEPARA: SrbChlType=HSPA;
SET UCORRMALGOSWITCH:
DraSwitch=DRA_BASE_ADM_CE_BE_TTI_L2_OPT_SWITCH-1&DRA_BASE_COVER_BE_TTI_L2
_OPT_SWITCH-1&DRA_BASE_RES_BE_TTI_L2_OPT_SWITCH-1;
SET UCORRMALGOSWITCH: ReservedSwitch0=RESERVED_SWITCH_0_BIT7-1;
//Deactivation procedure
//Deactivating the DC-HSUPA feature of the entire RNC
SET UCORRMALGOSWITCH: CfgSwitch=CFG_HSUPA_DC_SWITCH-0;
//Deactivating the DC-HSUPA feature of a specified cell
MOD UCELLALGOSWITCH: CellId=1, HspaPlusSwitch=DC_HSUPA-0;
MOD UCELLALGOSWITCH: CellId=2, HspaPlusSwitch=DC_HSUPA-0;
//(Optional) Removing a NodeB carrier group
RMV ULDUALCELLGRP: FIRSTLOCELL=0, SECONDLOCELL=2;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010688
Downlink Enhanced CELL_FACH.
Prerequisites
l Dependencies on Hardware
HBBI and HDLP on BTS3812E/BTS3812AE do not support this feature, EBBI, EDLP
is needed.
BBU3806 does not support this feature, EBBC or EBBCd is needed.
3900 series NodeB: WBBPa does not support this feature, and WBBPb, WBBPd or
WBBPf board are needed.
l Dependencies on Other Features
The configurations of the features on which this feature depends are complete. This
feature depends on the feature WRFD-010685 Downlink Enhanced L2.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The UE must be Release 7 (or later) UE and support this feature.
Context
This feature enables the FACH to be carried on the HS-DSCH. Based on this feature, the UE
can receive data at a higher rate in CELL_FACH state.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command MOD UCELLALGOSWITCH (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Algorithm Switches; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches) to select E_FACH(Cell E_FACH Function Switch) and
----End
Example
//Activating Downlink Enhanced CELL_FACH
163
Improvement of MIMO and HSDPA Co-carrier
Configuring Performance
This section describes how to activate, verify, and deactivate the optional feature WRFD-010700
Performance Improvement of MIMO and HSDPA Co-carrier.
Prerequisites
l Dependencies on Hardware
This feature is only supported by 40W RRU3801C, RRU3804, RRU3806, RRU3808,
WRFU, RRU3805, WRFUd, RRU3828, RRU3829, RRU3928, RRU3929, MRFUd,
MRFUe and 850M/900M/1900M RRU3908V1.
The BTS3812E/AE cannot support this feature.
The RRU3908 V2 and MRFU V2 modules support this feature from RAN14.0.
l Dependencies on Other Features
WRFD-010610 HSDPA Introduction Package
WRFD-010685 Enhanced L2
WRFD-010684 2x2 MIMO
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The UE must be support 2x2 MIMO.
The UE is of category 15, 16, 17, 18, as specified by the 3GPP protocols.
Context
CAUTION
Before enabling the feature in an existing cell, you need to deactivate the cell. This, however,
will interrupt services in the cell. Therefore, you should enable the feature when the traffic of
the cell is low.
The feature adopts MIMO in Primary/Secondary common Pilot (PSP) mode, Virtual Antenna
Mapping (VAM), and Intelligent Interference Control (ICC), improving performance of MIMO
and HSDPA co-carrier.
Data Planning
Procedure
l Activation Procedure
1. Run the BSC6900 MML command DEA UCELL (CME single configuration: UMTS
Cell Configuration Express > Cell Basic Information > Cell Basic Information.
Set Validation indication to Deactivated; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches) to deactivate MIMO cells.
2. On the NodeB, remove the old local cell and establish a new local cell.
a. Run the NodeB MML command RMV LOCELL (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Radio Layer > xx Sector >
Locell; CME batch modification center: not supported) to remove the local cell.
b. Run the NodeB MML command ADD LOCELL (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Radio Layer > xx Sector >
Locell; CME batch modification center: 3.17 Modifying Physical NodeB
Parameters in Batches) to add a local cell. In this step, set VAM to TRUE
(TRUE), TTW to TRUE and Precoding Weight Set Restriction Switch to
TRUE.
3. Run the NodeB MML command SET MACHSPARA (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Radio Layer > Locell Algorithm
Parameters > MAC Parameters > MACHSPARA; CME batch modification center:
3.17 Modifying Physical NodeB Parameters in Batches). In this step, set IIC
Switch to OPEN(open).
4. Configure the PSP function on the BSC6900 side.
Run the BSC6900 MML command MOD UCELLSETUP (CME single
configuration: UMTS Cell Configuration Express > Cell Basic Information >
Cell Basic Information; CME batch modification center: 3.18 Modifying UMTS
Cell Parameters in Batches) to modify the cell basic information. In this step, set
TX Diversity Indication to FALSE.
Run the BSC6900 MML command ADD USCPICH (CME single configuration:
UMTS Cell Configuration Express > Channel Configuration > SCPICH;
Example
l NodeB V200R014
//Activation procedure (using an RRU with only one transmit channel as
an example)
//Operations at the BSC6900
This section describes how to activate, verify, and deactivate the optional feature WRFD-010686
CPC - DTX /DRX.
Prerequisites
l Dependencies on Hardware
Dependencies on BSC6900 Hardware
This feature does not depend on the hardware.
Dependencies on NodeB Hardware
The BTS3812E, BTS3812A, or BTS3812AE is configured with the EBBI, EBOI,
EULP/EULPd (supporting DTX), and EDLP (supporting DRX) boards.
The BBU3806 is configured with the EBBC or EBBCd board.
The BBU3900 is configured with the WBBPb, WBBPd or WBBPf board.
l Dependencies on Other Features
The following features must be configured before this feature is activated:
WRFD-010636 SRB over HSUPA and WRFD-010652 SRB over HSDPA.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The UE is of 3GPP Release 7 or later and supports this feature.
Context
This feature is related to DTX and DRX. It can reduce the interference between UEs, improve
the HSPA+ user capacity per cell and save the battery consumption of the UE.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command MOD UCELLALGOSWITCH (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Algorithm Switches; CME batch modification center: 3.18 Modifying UMTS Cell
dtx-drx-TimingInfo
dtx-drx-Info
l Deactivation Procedure
1. Run the BSC6900 MML command MOD UCELLALGOSWITCH (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Algorithm Switches; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches). In this step, deselect DTX_DRX(Cell DTX_DRX
Function Switch) from the Cell Hspa Plus function switch drop-down list.
----End
Example
//Activating CPC - DTX /DRX
MOD UCELLALGOSWITCH: CellId=0, HspaPlusSwitch=DTX_DRX-1;
SET UCORRMALGOSWITCH: CfgSwitch=CFG_HSPA_DTX_DRX_SWITCH-1;
SET UFRCCHLTYPEPARA: SrbChlType=HSPA;
//Deactivating CPC - DTX /DRX
MOD UCELLALGOSWITCH: CellId=0, HspaPlusSwitch=DTX_DRX-0;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010687
CPC - HS-SCCH less operation.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The configurations of the features on which this feature depends are complete. This
feature depends on the feature WRFD-010652 SRB over HSDPA, WRFD-010636 SRB
over HSUPA.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The UE must be Release-7 (or later) to support this feature.
Context
This feature supports the HS-SCCH less operation function. With this feature, UE can receive
data from HS-PDSCH without sending data on HS-SCCH. This increases the capacity of
downlink data services.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, select
How to make the service on E-DCH, see section 97 Configuring HSUPA Introduction Package.
2. Check the RRC_RB_SETUP message traced over the Uu interface. You can find the
hs-scch-LessInfo IE which contains the parameters related to CPC-HSSCCH less
operation, as shown in Figure 165-1.
l Deactivation Procedure
Example
//Activating CPC-HS-SCCH Less operation
SET UCORRMALGOSWITCH: CfgSwitch=CFG_HSPA_HSSCCH_LESS_OP_SWITCH-1;
MOD UCELLALGOSWITCH: CellId=0, HspaPlusSwitch=HS_SCCH_LESS_OPERATION-1;
//Deactivating CPC-HS-SCCH Less operation
SET UCORRMALGOSWITCH: CfgSwitch=CFG_HSPA_HSSCCH_LESS_OP_SWITCH-0;
MOD UCELLALGOSWITCH: CellId=0, HspaPlusSwitch=HS_SCCH_LESS_OPERATION-0;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010697
E-DPCCH Boosting.
Prerequisites
l Dependencies on Hardware
The BTS3812E/BTS3812AE is configured with the Enhanced NodeB HSPA supported
Uplink Processing unit REV:d (EULPd) board, and the downlink services cannot be set
up on HBBI/HDLP/NDLP board.
The DBS3800 is configured with the Enhanced Base Band Card REV:d (EBBCd) board.
3900 series base stations are configured with WBBPd or WBBPf boards.
l Dependencies on Other Features
The feature WRFD-010612 HSUPA Introduction Package has been configured before
this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others
The UE is of 3GPP Release-7 or later and supports this feature.
CN supports data bit rate of 11.5Mbit/s or above.
Context
An E-DCH Dedicated Physical Control Channel (E-DPCCH) is used for channel estimation to
improve the estimation accuracy when the HSUPA service data is demodulated. In this way, the
requirement for Dedicated Physical Control Channel (DPCCH) power is lowered, increasing
the HSUPA service rate.
Procedure
l Activation Procedure
NOTE
When this feature is enabled together with the feature WRFD-010694 Uplink 16QAM, you are
advised to configure the network bandwidth over the Iub interface to 16 Mbit/s or higher if ATM
transmission is applied and to 15 Mbit/s or higher if IP transmission is applied.
1. Configure the bandwidth over the Iub interface in ATM transmission mode.
a. Configure the type of primary and secondary paths required by various services:
Run the BSC6900 MML command ADD TRMMAP (CME single
configuration: UMTS Global Configuration Express > Transmission
Resources Configuration > Transport Resource Mapping; CME batch
modification center: not supported). In this step, specify TRMMAP ID, set
Interface Type to IUB (Iub Interface) and Transport Type to ATM(ATM),
and specify SRB primary path and SRB secondary path.
b. Add an activation factor table: Run the BSC6900 MML command ADD
TRMFACTOR (CME single configuration: UMTS Global Configuration
Express > Transmission Resources Configuration > Factor Table; CME
batch modification center: not supported). In this step, specify Factor table
index and Remark, and change the activation factor.
c. Add the TRM mapping to an adjacent node: Run the BSC6900 MML
command ADD ADJMAP (CME single configuration: NodeB Configuration
Express > IUB_RNC > ATM Transport > Adjacent Node Mapping; CME
batch modification center: not supported). In this step, set Interface Type to
IUB (Iub Interface) and Transport Type of the adjacent node and interface
type to ATM(ATM), and specify Gold user TRMMAP index, Silver user
TRMMAP index, Bronze user TRMMAP index, and Factor table index.
d. Add ATM traffic records corresponding to the type of the primary and secondary
paths set in 1.1 (you are advised to configure the network bandwidth over the
Iub interface to 16 Mbit/s or higher): Run the BSC6900 MML command ADD
ATMTRF (CME single configuration: NodeB Configuration Express >
IUB_RNC > ATM Transport > ATM Traffic Record; CME batch
modification center: not supported). In this step, specify Traffic index, Service
type, Rate unit, and Peak cell rate.
e. Add an AAL2 path: Run the BSC6900 MML command ADD AAL2PATH
(CME single configuration: NodeB Configuration Express > IUB_RNC >
ATM Transport > AAL2 Path; CME batch modification center: not supported).
In this step, specify TX traffic record index and RX traffic record index.
2. Configure the bandwidth over the Iub interface in IP transmission mode.
a. Configure the type of primary and secondary paths required by various services:
Run the BSC6900 MML command ADD TRMMAP (CME single
configuration: UMTS Global Configuration Express > Transmission
Resources Configuration > Transport Resource Mapping; CME batch
modification center: not supported). In this step, specify TRMMAP ID, set
Interface Type to IUB (Iub Interface) and Transport Type to IP(IP), and
specify SRB primary path and SRB secondary path.
b. Add an activation factor table: Run the BSC6900 MML command ADD
TRMFACTOR (CME single configuration: UMTS Global Configuration
Express > Transmission Resources Configuration > Factor Table; CME
batch modification center: not supported). In this step, specify Factor table
index and Remark, and change the activation factor.
c. Add the TRM mapping to an adjacent node: Run the BSC6900 MML
command ADD ADJMAP (CME single configuration: NodeB Configuration
Express > IUB_RNC > IP Transport > Adjacent Node Mapping; CME batch
modification center: not supported). In this step, set Interface Type to IUB (Iub
Interface) and Transport Type of the adjacent node and interface type to IP
(IP), and specify Gold user TRMMAP index, Silver user TRMMAP index,
Bronze user TRMMAP index, and Factor table index.
d. Add an IP path (you are advised to configure the network bandwidth over the
Iub interface to 15 Mbit/s or higher): Run the BSC6900 MML command ADD
IPPATH (CME single configuration: NodeB Configuration Express >
IUB_RNC > IP Transport > IP Path; CME batch modification center: not
supported). In this step, specify Interface Type, Transport Type, IP path
type, Forward Bandwidth, and Backward Bandwidth.
e. Optional: Set the mapping from the PHB to the DSCP based on the service type:
Run the BSC6900 MML command SET PHBMAP (CME single configuration:
Device Panel > Board > Mapping Table Between PHB And DSCP; CME
batch modification center: not supported).
3. Configure the E-DPCCH Boosting function.
a. Turn on the E-DPCCH Boosting algorithm switch: Run the BSC6900 MML
command SET UCORRMALGOSWITCH (CME single configuration:
UMTS Radio Global Configuration Express > Connection_Oriented RRM
Switch Configuration > Connection Oriented Algorithm Switches; CME
batch modification center: 3.15 Modifying RNC Parameters in Batches). In
this step, set Channel Configuration Strategy Switch to
CFG_EDPCCH_BOOSTING_SWITCH.
b. Optional: If streaming services are to be enabled with E-DPCCH Boosting, run
the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, set Service Mapping Strategy Switch to
MAP_PS_STREAM_ON_HSUPA_SWITCH to ensure that streaming
services are carried over HSUPA.
c. Set the rate threshold for BE services and streaming services carried over
HSUPA: Run the BSC6900 MML command SET UFRCCHLTYPEPARA
(CME single configuration: UMTS Radio Global Configuration Express >
Basic Resource Control Parameter Configuration > Channel Type
Parameters; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, specify UL streaming traffic threshold
on HSUPA and UL BE traffic threshold on HSUPA.
d. Optional: Configure HSUPA-related parameters for a cell: Run the BSC6900
MML command ADD UCELLHSUPA (CME single configuration: UMTS Cell
Configuration Express > Cell Parameters > Configuration of HSUPA in
Cell; CME batch modification center: 3.18 Modifying UMTS Cell Parameters
in Batches).
NOTE
Retain the default values of Code Number for E-AGCH, Code Number for E-RGCH/
E-HICH, Maximum Target Uplink Load Factor, and Target Non-serving E-DCH
to Total E-DCH Power Ratio.
e. Activate the HSUPA function for a cell: Run the BSC6900 MML command ACT
UCELLHSUPA (CME single configuration: UMTS Cell Configuration
Express > Cell Parameters > Configuration of HSUPA in Cell. Set Cell
HSUPA state to Activated; CME batch modification center: No supported).
f. Enable the E-DPCCH Boosting function for a cell: Run the BSC6900 MML
command MOD UCELLALGOSWITCH (CME single configuration: UMTS
Cell Configuration Express > Cell Parameters > Cell Algorithm Switches;
CME batch modification center: 3.18 Modifying UMTS Cell Parameters in
Batches). In this step, set Cell Hspa Plus function switch to
EDPCCH_BOOSTING(Cell E-DPCCH Boosting Function Switch).
g. Turn on the E-DPCCH Boosting retry algorithm switch: Run the BSC6900 MML
command SET UFRC (CME single configuration: UMTS Radio Global
Configuration Express > Basic Resource Control Parameter
Configuration > RNC Oriented FRC Algorithm Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches). In this step,
set HSPA Technologies Retried by UEs to EDPCCH_BOOSTING.
h. Enable the E-DPCCH Boosting function for a cell on the NodeB side: Run the
NodeB MML command MOD LOCELL (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Radio Layer > xx Sector > Locell;
CME batch modification center: 3.17 Modifying Physical NodeB Parameters
in Batches).
l Verification Procedure
1. Establish PS BE HSUPA services with the uplink rate higher than 1 Mbit/s.
2. Trace messages over the Uu interface by referring to Tracing Messages on the Uu
Interface to check whether the RRC_RB_SETUP message carries the e-TFC-Boost-
Info information element (IE) that includes the e-TFCI-Boost and delta-T2TP fields,
as shown in Figure 166-1.
3. Trace messages over the Iub interface by referring to Tracing Messages on the Iub
Interface to check whether the NBAP_RL_RECFG_PREP message carries the e-
TFCI-Boost-Information IE that includes the e-TFCI-BetaEC-Boost and uL-
Delta-T2TP fields, as shown in Figure 166-2.
If the messages described in the preceding two steps carry the corresponding IEs,
the E-DPCCH Boosting function has taken effect.
If either of the messages described in the preceding two steps does not carry the
corresponding IEs, the E-DPCCH Boosting function has not taken effect.
l Deactivation Procedure
1. To disable the E-DPCCH Boosting function of all cells under the BSC6900, do as
follows: Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME
single configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, deselect the
CFG_EDPCCH_BOOSTING_SWITCH check box under the parameter Channel
Configuration Strategy Switch.
2. To disable the E-DPCCH Boosting function in a single cell, do as follows:
a. Method 1: Run the BSC6900 MML command MOD
UCELLALGOSWITCH (CME single configuration: UMTS Cell
Configuration Express > Cell Parameters > Cell Algorithm Switches; CME
batch modification center: 3.18 Modifying UMTS Cell Parameters in
Batches). In this step, deselect the EDPCCH_BOOSTING(Cell E-DPCCH
Boosting Function Switch) check box under the parameter Cell Hspa Plus
function switch to disable the E-DPCCH Boosting function in a cell on the
BSC6900 side.
b. Method 2: Run the NodeB MML command MOD LOCELL (CME single
configuration: NodeB Configuration Express > IUB_NodeB > Radio Layer
> xx Sector > Locell; CME batch modification center: 3.17 Modifying Physical
NodeB Parameters in Batches) to disable the E-DPCCH Boosting function in
a cell on the NodeB side.
----End
Example
/*Activating E-DPCCH Boosting */
transmission mode*/
//Adding ATM traffic records corresponding to the type of the primary and
secondary paths required by various services
ADD ATMTRF: TRFX=150, ST=RTVBR, UT=KBIT/S, PCR=16000, SCR=15000;
ADD ATMTRF: TRFX=151, ST=UBR, UT=KBIT/S, PCR=16000;
//Adding IP paths
ADD IPPATH: ANI=0, PATHID=2, ITFT=IUB, TRANST=IP, PATHT=AF11,
IPADDR="1.1.1.2", PEERIPADDR="1.1.1.1", PEERMASK="255.255.255.255",
TXBW=45000, RXBW=30000, CARRYFLAG=NULL, VLANFlAG=DISABLE,
PATHCHK=DISABLED;
ADD IPPATH: ANI=0, PATHID=2, ITFT=IUB, TRANST=IP, PATHT=AF12,
IPADDR="1.1.1.2", PEERIPADDR="1.1.1.1", PEERMASK="255.255.255.255",
TXBW=45001, RXBW=30001, CARRYFLAG=NULL, VLANFlAG=DISABLE,
PATHCHK=DISABLED;
//Disabling the E-DPCCH Boosting function in all cells on the RNC side
SET UCORRMALGOSWITCH: CfgSwitch= CFG_EDPCCH_BOOSTING_SWITCH-0;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010701
Uplink Enhanced CELL_FACH.
Prerequisites
l Dependencies on Hardware
Dependencies on the NodeB:
The BTS3812E, BTS3812A and BTS3812AE must be configured with the EULPd,
EBBI, EBOI or EULP board. The downlink services must be set up on the EBBI,
EBOI, or EULP board. The E-AI is not supported.
The DBS3800 must be configured with the EBBC or EBBCd board. The downlink
services must be set up on the EBBC or EBBCd board. To support the E-AI, the
DBS3800 must be configured with the EBBCd board.
The 3900 series base station must be configured with the WBBPb, WBBPd, or
WBBPf board. The downlink services must be set up on the WBBPb, WBBPd, or
WBBPf board. To support the E-AI, the 3900 series base station must be configured
with the WBBPd or WBBPf board.
l Dependencies on Other Features
The following features must be configured before this feature is activated:
WRFD-010688 Downlink Enhanced CELL_FACH
WRFD-010695 UL Layer 2 Improvement
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The UE must be Release-8 (or later) UE and support uplink for CELL_FACH
enhancement state.
Context
This feature enables the random access channel (RACH) to be mapped onto the E-DCH
Dedicated Physical Data Control Channel (E-DPDCH). With this feature, UEs in the
CELL_FACH state can transmit uplink data at higher rates.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command ADD UERACHBASIC (CME single
configuration: UMTS Cell Configuration Express > Channel Configuration >
ERACH Basic Information; CME batch modification center: not supported) to add
basic information about the Enhanced RACH (ERACH) function, namely Uplink
Enhanced CELL_FACH in a cell. In this step, set TTI for Common E-DCH.
2. Run the BSC6900 MML command ACT UCELLERACH (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > ERACH
Function. Set Cell ERACH state to Activated; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches) to activate this feature.
3. Run the NodeB MML commandMOD LOCELL (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Radio Layer > xx Sector > Locell; CME
batch modification center: 3.17 Modifying Physical NodeB Parameters in
Batches) to enable the UL L2 Enhanced and the ERACH function. In this step, set
the UL L2 Enhanced to TRUE, and set the ERACH to TRUE.
l Verification Procedure
1. Run the BSC6900 MML command DSP UCELL to check whether the ERACH is
available.
l Deactivation Procedure
1. Run the BSC6900 MML command DEA UCELLERACH (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > ERACH
Function. Set Cell ERACH state to Deactivated; CME batch modification center:
3.18 Modifying UMTS Cell Parameters in Batches) to deactivate this feature.
----End
Example
//Activating Uplink Enhanced CELL_FACH
ADD UERACHBASIC: CellId=11, CommonEdchTTISelect=TTI_10MS;
ACT UCELLERACH: CellId=11;
MOD LOCELL: LOCELL=11, SECT=REMOTE_SECTOR, UL_L2PLUS=TRUE, ERACH=TRUE;
//Verifying Uplink Enhanced CELL_FACH
DSP UCELL: DSPT=BYCELL, CellId=11;
//Deactivating Uplink Enhanced CELL_FACH
DEA UCELLERACH: CellId=11;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010653
96 HSDPA Users per Cell.
Prerequisites
l Dependencies on Hardware
In order to support this feature, EBBI, EBOI, EULP, EULPd is needed for BTS3812E
and BTS3812AE.
EBBC, EBBCd is needed for BBU3806.
WBBPb, WBBPd or WBBPf is needed for BBU3900.
l Dependencies on Other Features
The following features have been configured before this feature is activated:
WRFD-010623 64 HSDPA Users per Cell and WRFD-010686 CPC-DTX/DRX.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature enables an HSDPA cell to serve a maximum of 96 users performing VoIP or other
low-rate services, increasing capacity of voice services or other low-rate services.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command MOD UCELLCAC (CME single configuration:
UMTS Cell Configuration Express > Cell Parameters > Cell Oriented CAC
Algorithm Parameters; CME batch modification center: 3.18 Modifying UMTS
Cell Parameters in Batches) to stop reserving uplink and downlink credit resources
by setting UL handover credit reserved SF and DL handover credit and code
reserved SF to SFOFF(SFOFF), and setting Maximum HSDPA user number to
96.
l Verification Procedure
1. On the BSC6900 LMT, click Monitor. Then, double-click Cell Performance
Monitoring in the Monitor Navigation Tree pane. In the displayed Cell
Performance Monitoring dialog box, set Monitor Item to Cell User Number.
2. Use UEs to access the cell successively and then establish PS services, for example,
download files through FTP.
Expected result: Each UE establishes PS services successfully.
If the number of UEs is less than or equal to 96, uplink services are carried on
HSUPA channels and downlink services are carried on HSDPA channels.
If the number of UEs is greater than 96, HSPA services of the excessive UEs are
carried on R99 channels.
3. Check the maximum number of users through the counter
VS.HSDPA.UE.Max.Cell on the M2000.
NOTE
The 96 HSDPA users referred to in this feature are of the SRB Over HSPA type.
l Deactivation Procedure
1. This feature does not need to be deactivated.
----End
Example
/*Activating 96 HSDPA Users per Cell*/
//Stop reserving uplink and downlink credit resources and setting the
maximum number of HSDPA users to 96
MOD UCELLCAC: CellId=111, MaxHsdpaUserNum=96, UlHoCeResvSf=SFOFF,
DlHoCeCodeResvSf=SFOFF;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010639
96 HSUPA Users per Cell.
Prerequisites
l Dependencies on Hardware
In order to support this feature, EBBI, EBOI, EULP, EULPd is needed for BTS3812E
and BTS3812AE.
EBBC, EBBCd is needed for BBU3806.
WBBPb, WBBPd or WBBPf is needed for BBU3900.
l Dependencies on Other Features
The following features have been configured before this feature is activated:
WRFD-010634 60 HSUPA Users per Cell and WRFD-010653 96 HSDPA Users per
Cell.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature enables an HSUPA cell to serve a maximum of 96 users performing VoIP or other
low-rate services, increasing the capacity of voice services or other low-rate services per cell.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command MOD UCELLHSUPA (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters >
Configuration of HSUPA in Cell; CME batch modification center: 3.18 Modifying
UMTS Cell Parameters in Batches) to set Code Number for E-AGCH and Code
Number for E-RGCH/E-HICH to appropriate values.
2. Run the BSC6900 MML command MOD UCELLCAC (CME single configuration:
UMTS Cell Configuration Express > Cell Parameters > Cell Oriented CAC
Algorithm Parameters; CME batch modification center: 3.18 Modifying UMTS
Cell Parameters in Batches) to stop reserving uplink and downlink credit resources
by setting UL handover credit reserved SF and DL handover credit and code
reserved SF to SFOFF(SFOFF), and setting Maximum HSUPA user number to
96.
l Verification Procedure
1. On the BSC6900 LMT, click Monitor. Then, double-click Cell Performance
Monitoring in the Monitor Navigation Tree pane. In the displayed Cell
Performance Monitoring dialog box, set Monitor Item to Cell User Number.
2. Use UEs to access the cell successively and then establish PS services, for example,
upload files through FTP.
Expected result: Each UE establishes PS services successfully.
If the number of UEs is less than or equal to 96, uplink services are carried on
HSUPA channels and downlink services are carried on HSDPA channels.
If the number of UEs is greater than 96, HSPA services of the excessive UEs are
carried on R99 channels.
3. Check the maximum number of users indicated by the counter
VS.HSUPA.UE.Max.Cell on the M2000.
NOTE
The 96 HSUPA users referred to in this feature are of the SRB Over HSPA type.
l Deactivation Procedure
1. This feature does not need to be deactivated.
----End
Example
/*Activation procedure*/
//Stopping reserving uplink and downlink credit resources and setting the
maximum number of HSUPA users to 96
MOD UCELLCAC: CellId=111, MaxHsupaUserNum=96, UlHoCeResvSf=SFOFF,
DlHoCeCodeResvSf=SFOFF;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010654
128 HSDPA Users per Cell.
Prerequisites
l Dependencies on Hardware
The feature is only available for 3900 series NodeB, 3900 series NodeB (except
BTS3902E) requires WBBPd2/WBBPd3 board which is one type of WBBPd or
WBBPf.
l Dependencies on Other Features
The following features have been configured before this feature is activated:
WRFD-010653 96 HSDPA Users per Cell and WRFD-010670 128 HSUPA Users per
Cell.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature can increase the capacity of voice services in a cell, especially in cells with VoIP
users or a large number of low-rate users.
This feature enables an HSDPA cell to serve a maximum of 128 users performing VoIP or other
low-rate services. Note that these users must adopt the CPC-DTX/DRX mode.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command MOD UCELLCAC (CME single configuration:
UMTS Cell Configuration Express > Cell Parameters > Cell Oriented CAC
Algorithm Parameters; CME batch modification center: 3.18 Modifying UMTS
Cell Parameters in Batches) to stop reserving uplink and downlink credit resources
and set the maximum number of HSDPA users per cell to 128.
l Verification Procedure
1. On the BSC6900 LMT, click Monitor. Then, double-click Cell Performance
Monitoring in the Monitor Navigation Tree pane. In the displayed Cell
Performance Monitoring dialog box, set Monitor Item to Cell User Number.
2. Use UEs to access the cell successively and then establish PS services, for example,
download files through FTP.
Expected result: Each UE establishes PS services successfully.
If the number of UEs is less than or equal to 128, uplink services are carried on
HSUPA channels and downlink services are carried on HSDPA channels.
If the number of UEs is greater than 128, HSPA services of the excessive UEs are
carried on R99 channels.
3. Check the maximum number of users through the counter
VS.HSDPA.UE.Max.Cell on the M2000.
NOTE
The 128 HSDPA users referred to in this feature are of the SRB Over HSPA type.
l Deactivation Procedure
1. This feature does not need to be deactivated.
----End
Example
/*Activating 128 HSDPA Users per Cell*/
//Stop reserving uplink and downlink credit resources and setting the
maximum number of HSDPA users to 128
MOD UCELLCAC: CellId=111, MaxHsdpaUserNum=128, UlHoCeResvSf=SFOFF,
DlHoCeCodeResvSf=SFOFF;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010670
128 HSUPA Users per Cell.
Prerequisites
l Dependencies on Hardware
The feature is only available for 3900 series NodeB, 3900 series NodeB (except
BTS3902E) requires WBBPd2/WBBPd3 board which is one type of WBBPd or
WBBPf.
l Dependencies on Other Features
The following features have been configured before this feature is activated:
WRFD-010639 96 HSUPA Users per Cell and WRFD-010654 128 HSDPA Users per
Cell.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature can increase the capacity of voice services in a cell with a large number of low-rate
users, such as VoIP users.
This feature enables an HSUPA cell to serve a maximum of 128 users performing VoIP or other
low-rate services. Note that these users must adopt the CPC-DTX/DRX mode.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command MOD UCELLHSUPA (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters >
Configuration of HSUPA in Cell; CME batch modification center: 3.18 Modifying
UMTS Cell Parameters in Batches) to allocate code resources to E-AGCHs and E-
RGCHs.
2. Run the BSC6900 MML command MOD UCELLCAC (CME single configuration:
UMTS Cell Configuration Express > Cell Parameters > Cell Oriented CAC
Algorithm Parameters; CME batch modification center: 3.18 Modifying UMTS
Cell Parameters in Batches) to stop reserving uplink and downlink credit resources
and set the maximum number of HSUPA users to 128.
l Verification Procedure
1. On the BSC6900 LMT, click Monitor. Then, double-click Cell Performance
Monitoring in the Monitor Navigation Tree pane. In the displayed Cell
Performance Monitoring dialog box, set Monitor Item to Cell User Number.
2. Use UEs to access the cell successively and then establish PS services, for example,
upload files through FTP.
Expected result: Each UE establishes PS services successfully.
If the number of UEs is less than or equal to 128, uplink services are carried on
HSUPA channels and downlink services are carried on HSDPA channels.
If the number of UEs is greater than 128, HSPA services of the excessive UEs are
carried on R99 channels.
3. Check the maximum number of users indicated by the counter
VS.HSUPA.UE.Max.Cell on the M2000.
NOTE
The 128 HSUPA users referred to in this feature are of the SRB Over HSPA type.
l Deactivation Procedure
1. This feature does not need to be deactivated.
----End
Example
/*Activating 128 HSUPA Users per Cell*/
//Stop reserving uplink and downlink credit resources and setting the
maximum number of HSUPA users to 128
MOD UCELLCAC: CellId=111, MaxHsupaUserNum=128, UlHoCeResvSf=SFOFF,
DlHoCeCodeResvSf=SFOFF;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010704
Flexible HSPA+ Technology Selection.
Prerequisites
l Dependencies on Hardware
The BTS3812E, BTS3812A, and BTS3812AE must be configured with the EBBI,
EBOI, and EDLP boards. In addition, the uplink service cannot be established on the
HBBI or HULP board.
In DBS3800, the BBU3806 must be configured with the EBBC or EBBCd board.
The 3900 series base stations must be configured with the WBBPb, WBBPd or WBBPf
board.
BTS RF modules support only one transmission channel. MIMO requires
interconnection of two RF modules.
l Dependencies on Other Features
The following features must be configured before this feature is activated:
WRFD-010696 DC-HSDPA and RFD-010684 22 MIMO.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
In 22 MIMO mode, two RF units must be interconnected.
The UE has the HSDPA Category21 or higher capability, including HSDPA category
21, 22, 23, 24, 25, 26, 27, and 28.
Context
DC-HSDPA and MIMO can achieve gains under different conditions. DC-HSDPA ensures a
comparatively high throughput for the UEs when few HSDPA-capable UEs camp on a cell that
has a light load. MIMO ensures a comparatively high throughput for the UEs when a large
number of HSDPA-capable UEs camp on an overloaded cell.
When one or two carriers in DC-HSDPA networking support MIMO, Flexible HSPA+
Technology Selection dynamically selects DC-HSDPA or MIMO for newly accessing UEs,
based on the current number of HSDPA-capable UEs and downlink load of the carriers that
support MIMO. This ensures an optimum service bearing mode.
Procedure
l Activation Procedure
1. Turn on the DC/MIMO dynamic selection algorithm switch. Run the BSC6900 MML
command SET UCORRMALGOSWITCH (CME single configuration: UMTS
Radio Global Configuration Express > Connection_Oriented RRM Switch
Configuration > Connection Oriented Algorithm Switches; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches) with
CFG_DC_MIMO_DYNAMIC_SELECT_SWITCH selected in the Channel
Configuration Strategy Switch drop-down list.
2. Turn off the RNC-oriented DC+MIMO algorithm switch. Run the BSC6900 MML
command SET UCORRMALGOSWITCH (CME single configuration: UMTS
Radio Global Configuration Express > Connection_Oriented RRM Switch
Configuration > Connection Oriented Algorithm Switches; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches) with
CFG_HSDPA_DCMIMO_SWITCH deselected in the Channel Configuration
Strategy Switch drop-down list.
3. Optional: Turn on the HSDPA algorithm switch for streaming services if HSDPA is
required for streaming services. Run the BSC6900 MML command SET
UCORRMALGOSWITCH (CME single configuration: UMTS Radio Global
Configuration Express > Connection_Oriented RRM Switch Configuration >
Connection Oriented Algorithm Switches; CME batch modification center: 3.15
Modifying RNC Parameters in Batches) with
MAP_PS_STREAM_ON_HSDPA_SWITCH selected in the Service Mapping
Strategy Switch drop-down list.
4. Set HSDPA thresholds for downlink streaming services and HSDPA thresholds for
downlink BE services. Run the BSC6900 MML command SET
UFRCCHLTYPEPARA (CME single configuration: UMTS Radio Global
Configuration Express > Basic Resource Control Parameter Configuration >
Channel Type Parameters; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) with DL streaming traffic threshold on HSDPA and DL
BE traffic threshold on HSDPA set to appropriate values based on network planning.
l Verification Procedure
1. Set the TX power threshold and HSDPA user number threshold of the secondary cell
for the DC/MIMO dynamic selection algorithm. Run the BSC6900 MML command
SET UFRC with DL TX Power Threshold of Secondary Cell and Threshold of
HSDPA Users in Secondary Cell set to appropriate values.
2. Have a UE access the secondary cell and initiate an HSDPA service.
3. Query the DL power load of the secondary cell covered by the DC carrier group. On
the BSC6900 LMT, choose Monitor > Monitor > UMTS Monitoring > Cell
Performance Monitoring and select Cell DL Carrier TX Power in the Monitor
Item: drop-down list.
4. Check whether the value of the IE dl-TransportChannelType in the rb-MappingInfo
of the RRC_RB_SETUP message is hsdsch.
Expected result: As shown in Figure 172-2, the RRC_RB_SETUP message in the
Uu tracing result contains the mimoParameters IE when the downlink power of the
l Deactivation Procedure
1. Turn off the DC/MIMO dynamic selection algorithm switch. Run the BSC6900 MML
command SET UCORRMALGOSWITCH (CME single configuration: UMTS
Radio Global Configuration Express > Connection_Oriented RRM Switch
Configuration > Connection Oriented Algorithm Switches; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches) with
CFG_DC_MIMO_DYNAMIC_SELECT_SWITCH deselected in the Channel
Configuration Strategy Switch drop-down list.
----End
Example
//Activation procedure
//Turning on the DC/MIMO dynamic selection algorithm switch
SET UCORRMALGOSWITCH: CfgSwitch=CFG_DC_MIMO_DYNAMIC_SELECT_SWITCH-1;
//Turning off the RNC-oriented DC+MIMO algorithm switch
SET UCORRMALGOSWITCH: CfgSwitch=CFG_HSDPA_DCMIMO_SWITCH-0;
//(Optional) Enabling the HSDPA algorithm switch for streaming services
if HSDPA is required for streaming services
SET UCORRMALGOSWITCH: MapSwitch=MAP_PS_STREAM_ON_HSDPA_SWITCH-1;
//Setting the HSDPA threshold for downlink streaming services and HSDPA
threshold for downlink BE services
SET UFRCCHLTYPEPARA: DlStrThsOnHsdpa=D64, DlBeTraffThsOnHsdpa=D64;
//Verification procedure
SET UFRC: SecCellTcpThd=10, SecCellHUserNumThd=1;
//Deactivation procedure
SET UCORRMALGOSWITCH: CfgSwitch=CFG_DC_MIMO_DYNAMIC_SELECT_SWITCH-0;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010713
Traffic-Based Activation and Deactivation of the Supplementary Carrier In Multi-carrier.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
WRFD-010696 DC-HSDPA
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The UE must be of HS-DSCH category 21, 22, 23, 24 to support DC-HSDPA or HS-
DSCH category 25, 26, 27, 28 to support DC-HSDPA+MIMO.
Context
For a user that uses DC-HSDPA/DC-HSDPA+MIMO in the downlink and DCH/SC-HSUPA
in the uplink, the feature has the following functions:
l Disables the downlink secondary carrier function when the downlink traffic is light but the
buffer has been occupied by a large amount of data. In this case, the user becomes a single-
carrier user.
l Re-activate the downlink secondary carrier function when the buffer can accommodate a
large amount of data and throughput is high. In this case, the user becomes a dual-carrier
user.
Procedure
l Activation Procedure
1. Run the NodeB MML command SET MACHSPARA (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Radio Layer > Locell Algorithm
Parameters > MAC Parameters > MACHSPARA; CME batch modification center:
3.17 Modifying Physical NodeB Parameters in Batches) to set the Mac-hs
scheduling parameters with the DC HSDPA Cell Act Deact Switch set to ON
(ON).
NOTE
If the Mac-hs scheduling parameters of two DC-HSDPA cells must be set, set DC HSDPA
Cell Act Deact Switch to ON(ON) for each cell.
l Verification Procedure
1. Run the NodeB MML command LST MACHSPARA to query the Mac-hs scheduling
parameters. Check whether the Secondary DC HSDPA Cell Act Deact Switch is
turned on.
2. Run the BSC6900 MML command SET UCORRMALGOSWITCH. In this step,
clear DRA_HSDPA_STATE_TRANS_SWITCH,
DRA_HSUPA_STATE_TRANS_SWITCH, and
DRA_PS_BE_STATE_TRANS_SWITCH from the Dynamic Resource
Allocation Switch list.
3. Use a DC-HSDPA UE to perform PS services in a DC-HSDPA cell. Do not upload
or download data after required connections are established. Five seconds later, the
UE becomes an SC UE, which indicates that the feature has been activated.
l Deactivation Procedure
1. Run the NodeB MML command SET MACHSPARA (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Radio Layer > Locell Algorithm
Parameters > MAC Parameters > MACHSPARA; CME batch modification center:
3.17 Modifying Physical NodeB Parameters in Batches) to set the Mac-hs
scheduling parameters with the Secondary DC HSDPA Cell Act Deact Switch set
to OFF(OFF).
----End
Example
//Activation procedure
SET MACHSPARA: LOCELL=1, SECCELLACTDEASW=ON;
SET MACHSPARA: LOCELL=2, SECCELLACTDEASW=ON;
//Verification procedure
LST MACHSPARA: LOCELL=1;
LST MACHSPARA: LOCELL=2;
SET UCORRMALGOSWITCH:
DraSwitch=DRA_HSDPA_STATE_TRANS_SWITCH-0&DRA_HSUPA_STATE_TRANS_SWITCH-0&D
RA_PS_BE_STATE_TRANS_SWITCH-0;
//Deactivation procedure
SET MACHSPARA: LOCELL=1, SECCELLACTDEASW=OFF;
SET MACHSPARA: LOCELL=2, SECCELLACTDEASW=OFF;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010702
Enhanced DRX. (This feature cannot be configured using the CME. )
Prerequisites
l Dependencies on Hardware
NodeB:
The BTS3812E, BTS3812A, or BTS3812AE is configured with the EULPd, EBBI,
EBOI, or EULP board.
The BBU3806 is configured with the EBBC or EBBCd board.
The BBU3900 is configured with the WBBPb, WBBPd or WBBPf board.
l Dependencies on Other Features
Configurations of other features, on which this feature depends, are complete. This
feature depends on the feature WRFD-010688 Enhanced CELL_FACH.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The UE must be of 3GPP Release-8 or later and support Enhanced DRX.
HSPA+ Downlink 42Mbit/s per User
Context
The enhanced discontinuous reception (DRX) feature enables UEs in the enhanced downlink
for CELL_FACH state to receive the HS-SCCH discontinuously. After this feature is enabled,
the RAN and UEs in the enhanced downlink for CELL_FACH state transmit and receive data
at a specified time. The UE detects the HS-SCCH at regular intervals instead of detecting the
HS-SCCH continuously. When there is no data to transmit, the UE shuts down the receiver. As
a result, the power consumption of the UE decreases.
Procedure
l Activation Procedure
The BSC6900 MML command ADD UCELLEDRX fails to be executed in an active cell enabled
with enhanced downlink for CELL_FACH. Therefore, you need to deactivate enhanced downlink
for CELL_FACH before configuring the related parameters.
3. Run the BSC6900 MML command ADD UCELLEDRX to set parameters related to
enhanced DRX based on network planning requirements.
4. Run the BSC6900 MML command ACT UCELLEFACH to activate this feature.
l Verification Procedure
1. Start Uu Interface Trace on the LMT to trace messages on the Uu interface.
2. If the UE is not enabled with enhanced uplink for CELL_FACH, the information
element DRX Interruption by HS-DSCH data in the system information message
SIB5/5bis should be set to TRUE, as shown in Figure 174-1. If the UE is enabled
with enhanced uplink for CELL_FACH, the information element Common E-DCH
system info is carried in the system information message SIB5/5bis.
Figure 174-2 Indication sent from the RNC to the NodeB on the DCCH or DTCH
5. If the UE is enabled with enhanced uplink for CELL_FACH, the HS-DSCH DATA
FRAME type2 carries New IE Flag, H-RNTI, and E-RNTI, which can be viewed in
Cell Trace, as shown in Figure 174-3.
l Deactivation Procedure
1. Run the BSC6900 MML command MOD UCELLALGOSWITCH to deselect
E_DRX(Enhanced Discontinous Reception Function Switch) for Cell Hspa Plus
function switch.
----End
Example
//Activating enhanced DRX
MOD UCELLALGOSWITCH: CellId=11, HspaPlusSwitch=E_DRX-1;
DEA UCELLEFACH: CellId=11;
ADD UCELLEDRX: CellId=11, EDRXT321=EDRXT321_100, EDRXCycle=EDRXCYCLE_8,
EDRXBurst=EDRXBURST_1, EDRXInterruptbyHSDSCHData=INTERRUPTION_CFG;
ACT UCELLEFACH: CellId=11;
//Deactivating enhanced DRX
MOD UCELLALGOSWITCH: CellId=11, HspaPlusSwitch=E_DRX-0;
This section describes how to activate, verify, and deactivate the optional feature WRFD-020500
Enhanced Fast Dormancy. (This feature cannot be configured using the CME. )
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
NOTE
Context
As the number of smartphones keeps increasing in mobile networks, the networks face signaling
storms produced by these UEs. With rich experience in network optimization, Huawei provides
CAUTION
l Consult Huawei engineers about the comprehensive solution to obtain professional technical
support.
l Huawei engineers will recommend appropriate parameter settings for this feature based on
the network conditions.
l Do not configure the parameters related to this feature without Huawei professional technical
support. Inappropriate parameter settings may lead to network failures.
Always on line can be provided for PS services of intelligent UEs to improve user experience.
Always on line, however, will increase the power consumption of intelligent UEs. To prolong
UE battery life, the Fast Dormancy feature is introduced. When there is no PS data transfer, the
UE will send a signaling connection release indication (SCRI) message to request the
BSC6900 to release the RRC connection and move the UE state to IDLE mode, CELL_PCH,
or URA_PCH.
If this feature is not enabled, the BSC6900 will move the UE state to IDLE mode after the
BSC6900 receives an SCRI message from the UE or the UE inactivity timer expires. If UEs are
frequently switched between RRC connected states and IDLE mode, signaling storms occur.
If this feature is enabled, the BSC6900 will move the UE to the CELL_PCH or URA_PCH state
instead of the IDLE mode under either of the following conditions, reducing signaling processing
costs:
l The BSC6900 receives an SCRI message from the UE.
l The CELL_FACH/CELL_DCH inactivity timer on the BSC6900 expires.
Procedure
l Activation Procedure (The UE supporting fast dormancy is a Pre-Release 8 UE)
1. Run the BSC6900 MML command SET URRCTRLSWITCH to enable the feature
Enhanced Fast Dormancy at the BSC6900-level. In this step, select the
FAST_DORMANCY_SWITCH under PROCESSSWITCH.
2. Run the BSC6900 MML commandSET URRCTRLSWITCH to select the
RNC_PS_QUERY_UE_IMEI_SWITCH under PROCESSSWITCH2.
3. Run the BSC6900 MML command SET URRCTRLSWITCH to enable cell update
during CS service setup. In this step, clear the RSVDBIT1_BIT21 check box under
Reserved Parameter 1.
NOTE
After this feature is enabled, the FACH will carry a large amount of data, which may lead to
FACH congestion. Therefore, it is recommended that a new SCCPCH be added.
For details about how to handle FACH congestion in other methods, see section "FACH
Congestion Control" in the Flow Control in the RAN Feature Documentation.
5. Run the BSC6900 MML command SET UPSINACTTIMER to set the value of the
CELL_DCH, CELL_FACH, and CELL_PCH inactivity timer respectively.
The recommended value of the FAST DORMANCY USER T1 in
CELL_DCH is 5 seconds.
The recommended value of the FAST DORMANCY USER T1 in
CELL_FACH is 5 seconds.
The recommended value of the FAST DORMANCY USER T1 in
CELL_PCH is 1800 seconds.
NOTE
This document provide the recommended value of the FAST DORMANCY USER T1 in
CELL_DCH, the FAST DORMANCY USER T1 in CELL_FACH, and the FAST
DORMANCY USER T1 in CELL_PCH.
6. Run the BSC6900 MML command SET UUESTATETRANS. In this step, set Fast
Dormancy User FACH/E_FACH2DCH/HSPA 4A Threshold to D1024.
7. Run the BSC6900 MML command SET URRCTRLSWITCH to enable the Type
Allocation Code (TAC) match function. In this step, select the
FD_TAC_MATCH_SWITCH under PROCESSSWITCH.
8. Run the BSC6900 MML commandADD UIMEITAC to set the value of the TAC to
add the IMEI TACs of smartphones to the whitelist, set the The function of the
TAC to Fast_Dormancy, and set the Fast Dormancy Switch to ON.
9. Run the BSC6900 MML command ADD TRMFACTOR and MOD ADJMAP to
change the Iu-PS activity factor. The recommended value of the Iu-PS activity factor
is 10%. If the configured Iu-PS activity factor is smaller than 10%, retain the
configured value.
NOTE
After this feature is enabled, the number of UEs in the CELL_PCH or URA_PCH state increases
sharply. UEs in the CELL_PCH or URA_PCH state consume a large number of Iu-PS
bandwidth resources although they do not transmit any data.
Adjusting the Iu-PS activity factor can prevent PS service admission failures due to the increase
in the number of UEs in the CELL_PCH or URA_PCH state.
CAUTION
The Iu-PS activity factor of all services must be set to an appropriate value. Otherwise,
a large number of PS service setups fail, and the CPU usage of the SPU boards
increases sharply.
After this feature is enabled, the FACH will carry a large amount of data, which may lead to
FACH congestion. Therefore, it is recommended that a new SCCPCH be added.
For details about how to handle FACH congestion in other methods, see section "FACH
Congestion Control" in the Flow Control in the RAN Feature Documentation.
5. Run the BSC6900 MML command SET UPSINACTTIMER to set the value of the
CELL_DCH, CELL_FACH, and CELL_PCH inactivity timer respectively.
The recommended value of the FAST DORMANCY USER T1 in
CELL_DCH is 5 seconds.
The recommended value of the FAST DORMANCY USER T1 in
CELL_FACH is 5 seconds.
The recommended value of the FAST DORMANCY USER T1 in
CELL_PCH is 1800 seconds.
NOTE
This document provide the recommended value of the FAST DORMANCY USER T1 in
CELL_DCH, the FAST DORMANCY USER T1 in CELL_FACH, and the FAST
DORMANCY USER T1 in CELL_PCH.
6. Run the BSC6900 MML command SET UUESTATETRANS. In this step, set Fast
Dormancy User FACH/E_FACH2DCH/HSPA 4A Threshold to D1024.
7. Run the BSC6900 MML command SET URRCTRLSWITCH to enable the Type
Allocation Code (TAC) match function. In this step, select the
FD_TAC_MATCH_SWITCH under PROCESSSWITCH.
8. Optional: To enable this feature only for UEs of Release 8 or later versions on the
live network, Run the BSC6900 MML commandRMV UIMEITAC to remove the
TAC values for these UEs.
9. Run the BSC6900 MML command ADD TRMFACTOR and MOD ADJMAP to
change the Iu-PS activity factor. The recommended value of the Iu-PS activity factor
is 10%. If the configured Iu-PS activity factor is smaller than 10%, retain the
configured value.
NOTE
After this feature is enabled, the number of UEs in the CELL_PCH or URA_PCH state increases
sharply. UEs in the CELL_PCH or URA_PCH state consume a large number of Iu-PS
bandwidth resources although they do not transmit any data.
Adjusting the Iu-PS activity factor can prevent PS service admission failures due to the increase
in the number of UEs in the CELL_PCH or URA_PCH state.
CAUTION
The Iu-PS activity factor of all services must be set to an appropriate value. Otherwise,
a large number of PS service setups fail, and the CPU usage of the SPU boards
increases sharply.
l Verification Procedure
1. Run the BSC6900 MML command DSP LICUSAGE to query the state of the license
for this feature. If the result shown in Figure 175-1 is returned, the license for this
feature has been configured.
4. Keep the UE in IDLE mode for 10 seconds and perform no operation after a Web page
is opened.
If the RRC_RB_RECFG message shown in Figure 175-3 is traced, the UE will move
from the CELL_DCH state to the CELL_FACH state and then to the CELL_PCH
state.
5. Use the UE to continue PS services such as web page browsing. Cell update or channel
reconfiguration occurs.
l Deactivation Procedure
To deactivate this feature for all UEs on the live network, Run the BSC6900 MML
commandSET URRCTRLSWITCH. In this step, clear
FAST_DORMANCY_SWITCH under Process switch parameter to turn off the
BSC6900-level switch for enhanced fast dormancy.
To deactivate this feature only for UEs of versions earlier than Release 8 on the live
network, Run the BSC6900 MML commandRMV UIMEITAC to remove the TAC
values for these UEs.
To deactivate this feature only for UEs of Release 8 or later versions on the live network,
Run the BSC6900 MML commandSET UCONNMODETIMER. In this step, set
Timer 323 to INVALID.
NOTE
If this feature must be deactivated when the SPUa or SPUb board is being reset, do as follows:
1. Run the BSC6900 MML command SET CFGDATAINEFFECTIVE to set the subrack to ineffective
mode.
2. Run the MML commands to deactivate this feature. For details, see the script in the example.
3. Run the BSC6900 MML command SET CFGDATAEFFECTIVE to set the subrack to effective
mode.
----End
Example
//Activating Fast Dormancy Enhancement (The UE supporting fast dormancy
is a Pre-Release 8 UE)
Phone", FastDormancy=ON;
176
Experience Improvement for Weak Reception
Configuring Voice Service
UEs
This section describes how to activate, verify, and deactivate the optional feature WRFD-140205
Voice Service Experience Improvement for Weak Reception UEs.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature enables the radio network controller (RNC) to identify weak reception UEs based
on the International Mobile Station Equipment Identity (IMEI) and to configure dedicated power
control and handover parameters for them. Based on the parameter settings, weak reception UEs
obtain a high downlink power control threshold in weak coverage areas and perform handovers
at the designated threshold. This prevents frequent compressed mode measurement and call
drops caused by signal quality fluctuations and improves user experience of CS voice services.
l Precautions
None
l Data Preparation
Procedure
l Activation Procedure
1. Optional: Enable the CS international mobile equipment identity (IMEI) acquisition
function on the BSC6900.
a. Run the BSC6900 MML command SET URRCTRLSWITCH (CME single
configuration: UMTS Radio Global Configuration Express > Process Switch
Configuration > Process Switch; CME batch modification center: 3.15
Modifying RNC Parameters in Batches). In this step, select the
RNC_CS_QUERY_UE_IMEI_SWITCH check box under Process Control
Switch 2.
NOTE
l If CS IMEI acquisition has been enabled on the CN, skip this step.
l Before enabling CS IMEI acquisition, ensure that the CN checks the serial number of direct
transfer messages. Run the BSC6900 MML command SET URRCTRLSWITCH (CME single
configuration: UMTS Radio Global Configuration Express > Process Switch
Configuration > Process Switch; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, turn on the SEND_MSG_NULL_SWITCH switch.
l After enabling CS IMEI acquisition, check for the compatibility issue between the BSC6900
and the CN. When there is a compatibility issue, enabling CS IMEI acquisition results in CS
service setup failures.
2. Enable differentiated power control and differentiated handover for smartphones, and
configure the Type Allocation Code (TAC) of the smartphone.
a. Run the BSC6900 MML command ADD UIMEITAC (CME single
configuration: UMTS Global Configuration Express > RNC Basic
Configuration > IMEI TAC; CME batch modification center: not supported).
In this step, set The function of the TAC to Special_User_Enhance, and select
the SPECUSER_AMR_HOENHANCE_SWITCH and
To enable this feature in a specified cell, run the ADD UCELLHOCOMM (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell Oriented
Handover Common Algorithm Parameters; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches) command to set the differentiated handover
parameters for the cell.
l Verification Procedure
l Deactivation Procedure
1. Disable differentiated power control and differentiated handover for smartphones.
a. Run the BSC6900 MML command MOD UIMEITAC (CME single
configuration: UMTS Global Configuration Express > RNC Basic
Configuration > IMEI TAC; CME batch modification center: not supported).
In this step, set The function of the TAC to Special_User_Enhance, and clear
the SPECUSER_AMR_HOENHANCE_SWITCH and
SPECUSER_AMR_PWRENHANCE_SWITCH check boxes under
SpecUserFunctionSwitch.
b. Optional: Run the BSC6900 MML command SET URRCTRLSWITCH
(CME single configuration: UMTS Radio Global Configuration Express >
Process Switch Configuration > Process Switch; CME batch modification
center: 3.15 Modifying RNC Parameters in Batches). In this step, clear the
RNC_CS_QUERY_UE_IMEI_SWITCH check box under Process Control
Switch 2.
----End
Example
//Activating Voice Experience Improvement for Smartphones
//Enabling CS IMEI acquisition
SET URRCTRLSWITCH: PROCESSSWITCH2=RNC_CS_QUERY_UE_IMEI_SWITCH-1;
//Enabling differentiated power control and differentiated handover for
smartphones and setting the TAC of the smartphone
ADD UIMEITAC: TAC_FUNC=Special_User_Enhance, TAC=12345,
Description="Smart Phone",
SpecUserFunctionSwitch=SPECUSER_AMR_HOENHANCE_SWITCH-1&SPECUSER_AMR_PWREN
HANCE_SWITCH-1;
//Setting the parameters related to cell load monitoring
This section describes how to activate, verify, and deactivate the optional feature WRFD-140206
Layered Paging in URA_PCH.
Prerequisites
l Dependency on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The URA_PCH state has been enabled and CellReSelectCounter in the SET
UUESTATETRANS (CME single configuration: UMTS Radio Global
Configuration Express > UE State Transition Parameter Configuration > UE State
Translating Parameters; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) command has been specified to enable UEs to easily enter the
URA_PCH state.
Before the feature activation, it is recommended that Enhanced Fast Dormancy be
activated and parameters related to the D2F state transition be configured to enable
smartphones to enter the URA_PCH state if possible.
Context
Due to the rapid rise of smart phone use in recent years, paging messages have been increasing.
Conventionally, paging messages are sent to the entire UTRAN registration area (URA). Once
Layered Paging in URA_PCH is activated, paging messages are first sent to the last camped-on
cell of the UEs in the URA_PCH state and the neighboring cells of the last camped-on cell.
When necessary, these messages will be sent to the URA. This reduces the number of paging
messages and the possibility of PCH congestion, eliminates the need for manually dividing
URAs, and reduces the number of URA updates.
l Precautions
None.
l Data Preparation
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET URRCTRLSWITCH (CME single
configuration: UMTS Radio Global Configuration Express > Process Switch
Configuration > Process Switch; CME batch modification center: 3.15 Modifying
RNC Parameters in Batches). In this step,
Select the URAPCH_LAYERED_PAGING_RT_SWITCH check box under
the PROCESSSWITCH parameter to enable Layered Paging in URA_PCH for
real-time services.
Select the URAPCH_LAYERED_PAGING_NRT_SWITCH check box under
the PROCESSSWITCH parameter to enable Layered Paging in URA_PCH for
non-real-time services.
l Verification Procedure
Check the value of the counter VS.Paging1.Att1.URA.RealTime.Cell or
VS.Paging1.Att1.URA.NonRealTime.Cell on the M2000. If either counter is set to a value
other than 0, this feature has been activated.
l Deactivation Procedure
1. Run the BSC6900 MML command SET URRCTRLSWITCH (CME single
configuration: UMTS Radio Global Configuration Express > Process Switch
Configuration > Process Switch; CME batch modification center: 3.15 Modifying
RNC Parameters in Batches). In this step,
Example
//Enabling Layered Paging in URA_PCH for real-time services
SET URRCTRLSWITCH: PROCESSSWITCH=URAPCH_LAYERED_PAGING_RT_SWITCH-1;
//Enabling Layered Paging in URA_PCH for non-real-time services
SET URRCTRLSWITCH: PROCESSSWITCH=URAPCH_LAYERED_PAGING_NRT_SWITCH-1;
//Disabling Layered Paging in URA_PCH for real-time services
SET URRCTRLSWITCH: PROCESSSWITCH=URAPCH_LAYERED_PAGING_RT_SWITCH-0;
//Disabling Layered Paging in URA_PCH for non-real-time services
SET URRCTRLSWITCH: PROCESSSWITCH=URAPCH_LAYERED_PAGING_NRT_SWITCH-0;
This section describes how to activate, verify, and deactivate the optional feature WRFD-020132
Web browsing acceleration. (This feature cannot be configured using the CME. )
Prerequisites
l Dependencies on RNC hardware
NIUa board is required.
l Dependencies on NodeB Hardware
BTS3812E and BTS3812AE series base stations are configured with EBBI or EDLP
boards. HBBI and HDLP boards do not support this feature.
DBS3800 series base stations are configured with EBBC or EBBCd boards. The HBBU
board does not support this feature.
3900 series base stations are configured with WBBPb, WBBPd or WBBPf boards. The
WBBPa board does not support this feature.
The Network Intelligence Unit REV:a (NIUa) board is ready. The NIUa board can be
housed in the same slot as the DPUb or DPUe board. For details of inserting a NIUa
board, see Inserting a Board.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
NOTE
Context
This feature enables the RNC to identify web browsing services by parsing packets and thereby
to preferentially allocate higher bandwidth to these services. As a result, web browsing services
take shorter time and the user experience is improved.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command ADD BRD to add a NIUa board. In this step, set
the Board Class to NIU, and set the Board Type to NIUa.
2. Set the initial Scheduling Priority Indicator (SPI) weight on the BSC6900 LMT.
If the switch for the license control item of the feature WRFD-020806
Differentiated Service Based on SPI Weight is turned on, run the BSC6900
MML command SET USPIWEIGHT to configure weight of each SPI. In this
step, set Scheduling Priority Indicator and SPI Weight to appropriate values
based on the network plan.
If the switch for the license control item of the feature WRFD-020806
Differentiated Service Based on SPI Weight is not turned on, run the BSC6900
MML command SET UFRC to set Default SPI Weight to an appropriate value
based on the network plan.
3. Run the BSC6900 MML command SET URRCTRLSWITCH. In this step, select
the NODEB_PRIVATE_INTERFACE_SWITCH check box under the parameter
Process switch.
4. Run the BSC6900 MML command ADD UIPSERVICEQOS. In this step, set the
Traffic Type to HTTP, and set the Traffic Priority to HIGH.
5. Run the BSC6900 MML command SET UDPUCFGDATA. In this step, set
Scheduling Priority Weight for High PRI Service, Scheduling Priority Weight
for Middle PRI Service, and Scheduling Priority Weight for Low PRI Service to
appropriate values based on the network plan.
l Verification Procedure
1. Verify that the value of the counter VS.IuPS.BytesPayldHTTP.Rx is not 0. If it is not
0, this feature has been activated.
l Deactivation Procedure
1. This feature does not need to be deactivated.
----End
Example
//Activating Web Browsing Acceleration
//Setting the initial SPI weight value if the switch for the license
control item of the feature WRFD-020806 Differentiated Service Based on
SPI Weight is turned on
SET USPIWEIGHT: SPI=4, SPIWEIGHT=10;
//Setting the initial SPI weight value if the switch for the license
control item of the feature WRFD-020806 Differentiated Service Based on
SPI Weight is not turned on
SET UFRC: DefaultSPIWeight=10;
This section describes how to activate, verify, and deactivate the optional feature WRFD-020133
P2P Downloading Rate Control during Busy Hour. (This feature cannot be configured using the
CME. )
Prerequisites
l Dependencies on Hardware
Dependencies on RNC Hardware
NIUa board is required.
Dependencies on NodeB Hardware
BTS3812E and BTS3812AE series base stations are configured with EBBI or EDLP
boards. HBBI and HDLP boards do not support this feature.
DBS3800 series base stations are configured with EBBC or EBBCd boards. The
HBBU board does not support this feature.
3900 series base stations are configured with WBBPb or WBBPd boards. The
WBBPa board does not support this feature.
The Network Intelligence Unit REV:a (NIUa) board is ready. The NIUa board can
be housed in the same slot as the DPUb or DPUe board. For details of inserting a
NIUa board, see Inserting a Board.
l Dependencies on Other Features
This feature does not depend on other features.
NOTE
Context
This feature restricts point to point service (P2P) traffic during busy hours, thereby improving
the user experience of other delay-sensitive services and reducing operating costs. During non-
busy hours, P2P downloads are not restricted, thereby improving the user experience of P2P
users and full utilizing network resources.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command ADD BRD to add a NIUa board. In this step, set
the Board Class to NIU, and set the Board Type to NIUa.
2. Set the initial Scheduling Priority Indicator (SPI) weight on the BSC6900 LMT.
If the switch for the license control item of the feature WRFD-020806
Differentiated Service Based on SPI Weight is turned on, run the BSC6900
MML command SET USPIWEIGHT to configure weight of each SPI. In this
step, set Scheduling Priority Indicator and SPI Weight to appropriate values
based on the network plan.
If the switch for the license control item of the feature WRFD-020806
Differentiated Service Based on SPI Weight is not turned on, run the BSC6900
MML command SET UFRC to set Default SPI Weight to an appropriate value
based on the network plan.
3. Run the BSC6900 MML command SET URRCTRLSWITCH. In this step, select
the NODEB_PRIVATE_INTERFACE_SWITCH check box under the parameter
Process switch.
4. Run the BSC6900 MML command ADD UIPSERVICEQOS to add the priority
mapping of P2P services.
5. Run the BSC6900 MML command SET UDPUCFGDATA to set scheduling priority
weight that corresponds to services of each priority to appropriate values.
l Verification Procedure
1. Verify that the value of the counter VS.IuPS.BytesPayldP2P.Rx is not 0. If it is not 0,
this feature has been activated.
l Deactivation Procedure
1. This feature does not need to be deactivated.
----End
Example
//Activating P2P Downloading Rate Control during Busy Hour
//Setting the initial SPI weight value if the switch for the license
control item of the feature WRFD-020806 Differentiated Service Based on
SPI Weight is turned on
SET USPIWEIGHT: SPI=4, SPIWEIGHT=10;
//Setting the initial SPI weight value if the switch for the license
control item of the feature WRFD-020806 Differentiated Service Based on
SPI Weight is not turned on
This section describes how to activate, verify, and deactivate the optional feature WRFD-020116
Dynamic Power Sharing of Multi-Carriers.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
WRFD-010610 HSDPA Introduction Package
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
Dynamic Power Sharing of Multi-Carriers means that among multiple carriers, the carrier
bearing HSPA service can dynamically share the unused power resource of another carrier. This
function increases the utilization of the power amplifier as well as the HSPA service rate of the
cell. For asymmetrical power configuration, the carrier with higher emitting power cannot share
the unused power resource of the carrier with lower emitting power.
Procedure
l Activation Procedure
1. Run the NodeB MML command ADD PAGRP (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Radio Layer > Other Information >
PAGRP; CME batch modification center: not supported) to add a power sharing
group.
NOTE
Example
//Activation procedure
ADD PAGRP: SLOCELL=1, DLOCELL=2, MAXSHRTO=50, SHMGN=10;
//Deactivation procedure
RMV PAGRP: DLOCELL=2;
This section describes how to activate, verify, and deactivate the optional feature WRFD-020117
Multi-Carrier Switch off Based on Traffic Load.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
l The power consumption evaluation of the products in mobile networks shows that the
devices, particularly the base stations, in the radio access network are the principal
contributor of power consumption and CO2 emissions when they are functioning.
l If multiple carriers are used in the same coverage area, Huawei provides operators with
adaptive carrier power management to reduce power consumption. The traffic volume
varies with time. For example, a base station in the Central Business District (CBD) has a
higher traffic volume in the daytime, which requires more than one carrier to serve all the
subscribers; the traffic volume becomes low from midnight to early morning of the next
day. From RAN10.0 on, during an idle period that is configurable by operators, the RNC
dynamically shuts down the carriers on which there is no service and uses the other carriers
in the same area. The carriers will be turned on again when the traffic on the other carriers
becomes congested or when the idle period ends. This reduces power consumption.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET URNCCELLSHUTDOWNPARA (CME
single configuration: UMTS Radio Global Configuration Express > RNC_Lever
NOTE
This feature takes effect only when the GBP measurement switch for the inter-frequency co-
coverage neighboring cell is turned on.
l Verification Procedure
1. Start alarm browsing on the BSC6900 LMT.
2. Ensure that the total number of users in cell 1 and cell 2 is 0. Alternatively, set up two
inter-frequency co-coverage neighboring cells where no user is admitted.
3. At a time during the period specified by running the BSC6900 MML command ADD
UCELLDYNSHUTDOWN (for example, 09:10):
If an ALM-22202 UMTS Cell Unavailable is reported at cell 1 with the cause value
of cell dynamic shutdown, this feature has been activated.
If this alarm is not reported or is reported but the cause value is not cell dynamic
shutdown, this feature is not activated.
4. Check whether this feature is activated by viewing the counter
VS.DynOpen.CellSetup and check whether this feature is deactivated by viewing the
counter VS.DynClose.CellDel on the M2000.
l Deactivation Procedure
1. Run the BSC6900 MML command SET URNCCELLSHUTDOWNPARA (CME
single configuration: UMTS Radio Global Configuration Express > RNC_Lever
Cell Dynamic ShutDown Parameter Configuration > Cell Dynamic Shutdown
Parameters in RNC; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to deactivate this feature at the RNC. In this step, set Cell
Dynamic ShutDown Switch For RNC to OFF(switch off).
2. Optional: Run the BSC6900 MML command RMV UCELLDYNSHUTDOWN
(CME single configuration: UMTS Cell Configuration Express > Cell
Parameters > Cell Dynamic Shutdown Parameters; CME batch modification
center: not supported) to deactivate this feature for cell 1.
----End
Example
/*Activation procedure*/
//Turning on the RNC-level switch for dynamic shutdown
SET URNCCELLSHUTDOWNPARA: DynCellShutDownSwitch=ON;
//Turning on the cell-level switch for dynamic shutdown
ADD UCELLDYNSHUTDOWN: CellId=1, DynShutdownSwitch=ON_1, StartTime1=08&59,
EndTime1=10&59, DynShutDownType=CONDITIONALSHUTDOWN;
//Adding inter-frequency co-coverage neighboring cells for the cell where
this feature is activated (cell 1 and cell 2 in the following command are
served by the same NodeB)
ADD UINTERFREQNCELL: RNCId=110, CellId=1, NCellRncId=110, NCellId=2,
SIB11Ind=TRUE, SIB12Ind=FALSE, TpenaltyHcsReselect=D0, BlindHoFlag=TRUE,
NPrioFlag=FALSE, InterNCellQualReqFlag=FALSE;
This section describes how to activate, verify, and deactivate the optional feature WRFD-020118
Energy Efficiency Improved.
Prerequisites
l Dependencies on Hardware
MTRU of the BTS3812E/BTS3812AE does not support this feature.
The RRU3801C of the NodeB does not support this feature.
Other RF modules support this feature.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
l Based on the high efficient power amplification techniques, power amplification
parameters can be dynamically adjusted to further improve the power amplification
efficiency under low load. The NodeB adjusts the Power Amplifier (PA) bias voltage based
on the output power that varies with the traffic load, improving the PA efficiency and
reducing the static PA power consumption.
l When there is no HSDPA service, the NodeB supports this function as long as the license
is activated.
l When there are HSDPA services, the NodeB does not support this function by default. If
this function is required, perform the following activation operations.
Procedure
l Activation Procedure
1. Run the NodeB MML command SET OPTDYNADJPARA (CME single
configuration: NodeB Configuration Express > IUB_NodeB > Basic
Example
//Activation procedure SET OPTDYNADJPARA: DYNADJSWITCH=ON,
DYNADJSTARTTIME=0, DYNADJENDTIME=6;
//Verification procedure LST OPTDYNADJPARA:;
//Deactivation procedure SET OPTDYNADJPARA: DYNADJSWITCH=OFF;
This section describes how to activate, verify, and deactivate the optional feature WRFD-020119
Multi-Carrier Switch off Based on Power Backup.
Prerequisites
l Dependencies on Hardware
The BTS3902E doesn't support this feature.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
In case of mains failure, the backup power system starts to operate. In this case, this feature can
implement hierarchical carrier shutdown based on the shutdown duration and cell priority.
Procedure
l NodeB V200R014
Activation Procedure
1. Run the NodeB MML command MOD LOCELL (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Radio Layer > xx Sector > Locell; CME
batch modification center: 3.17 Modifying Physical NodeB Parameters in
Batches) with Local Cell ID and Sector Type specified in order to set reserved cells.
For the cells that need to provide services continuously during the level-1 shutdown
period, set Reserved Cell to TRUE.
NOTE
It is recommended that at least one cell be reserved for a sector. In case of mains failure, the
reserved cell continues to provide services for the users in this sector.
Before a cell is shut down, the smooth power change function reduces the TX power of the P-
CPICH so that the services in the cell are handed over to neighboring cells. This prevents service
disruption due to abrupt cell shutdown.
Verification Procedure
1. Run the NodeB MML command LST LOWPOWERPARA to query the
configuration information about the intelligent power shutdown switch. On the LMT,
check whether the NodeB ISD Switch is set to ENABLE, and whether the Level 1
power off Delay (s) and Level 2 power off Delay (s) are set correctly.
2. Run the NodeB MML command LST LOCELL to query the configuration
information about local cells. Check whether the value of Reserve Cell of each local
cell is correct.
3. Optional: If the smooth power change function is already used, run the NodeB MML
command LST SMTHPWRSWTCH to check whether the intelligent power
shutdown switch is turned on. If the Smooth Power Change Function Switch is set
to OPEN, it indicates that this function is enabled.
Deactivation Procedure
1. Run the NodeB MML command MOD LOWPOWERPARA (CME single
configuration: NodeB Configuration Express > IUB_NodeB > Basic
Information > Equipment Management > NODEB; CME batch modification
center: not supported) to turn off the intelligent power shutdown switch with the
NodeB ISD Switch set to DISABLE.
l NodeB V100R014
Activation Procedure
1. Run the NodeB MML command MOD LOCELL (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Radio Layer > xx Sector > Locell; CME
batch modification center: 3.17 Modifying Physical NodeB Parameters in
Batches) with Local Cell ID and Sector Type specified in order to set reserved cells.
For the cells that need to provide services continuously during the level-1 shutdown
period, set Reserved Cell to TRUE.
NOTE
It is recommended that at least one cell be reserved for a sector. In case of mains failure, the
reserved cell continues to provide services for the users in this sector.
2. Run the NodeB MML command SET ITELSHUTDOWN (CME single
configuration: NodeB Configuration Express > IUB_NodeB > Basic
Information > More Information > NODEB; CME batch modification center: not
supported) to set the intelligent power shutdown switch with the ISD SWITCH set
to ENABLE. Set LEVEL1 DELAY and LEVEL2 DELAY based on the backup
capability of the batteries.
3. Optional: If you need to use the smooth power change function, run the NodeB MML
command SET SMTHPWRSWTCH (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Basic Information > Basic Information
> Smooth Power Change Function Switch; CME batch modification center: not
supported) to set the intelligent power shutdown switch with the Smooth Power
Change Function Switch set to OPEN.
NOTE
Before a cell is shut down, the smooth power change function reduces the TX power of the P-
CPICH so that the services in the cell are handed over to neighboring cells. This prevents service
disruption due to abrupt cell shutdown.
Verification Procedure
1. Run the NodeB MML command LST ITELSHUTDOWN to query the configuration
information about the intelligent power shutdown switch. On the LMT, check whether
the NodeB ISD Switch is set to ENABLE, and whether the Level 1 power off and
Level w power off are set correctly.
2. Run the NodeB MML command LST LOCELL to query the configuration
information about local cells. Check whether the value of Reserve Cell of each local
cell is correct.
3. Optional: If the smooth power change function is already used, run the NodeB MML
command LST SMTHPWRSWTCH to check whether the intelligent power
shutdown switch is turned on. If the Smooth Power Change Function Switch is set
to OPEN, it indicates that this function is enabled.
Deactivation Procedure
----End
Example
l NodeB V200R014
//Activation procedure
MOD LOCELL: LOCELL=1, SECT=LOCAL_SECTOR, RSV=TRUE;
MOD LOWPOWERPARA: ISD=ENABLE, LEVEL1=60, LEVEL2=120;
SET SMTHPWRSWTCH: SWITCH=OPEN;
//Verification procedure
LST LOWPOWERPARA:;
LST LOCELL: MODE=LOCALCELL, LOCELL=1;
LST SMTHPWRSWTCH:;
//Deactivation procedure
MOD LOWPOWERPARA: ISD=DISABLE;
l NodeB V100R014
//Activation procedure
MOD LOCELL: LOCELL=1, SECT=LOCAL_SECTOR, RSV=TRUE;
This section describes how to activate, verify, and deactivate the optional feature WRFD-020122
Multi-Carrier Switch off Based on QoS.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The feature WRFD-010610 HSDPA Introduction Package has been configured before
this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature guarantees the data rate for only DCH and high-priority HSDPA users. For low-
priority HSDPA users, only Guaranteed Bit Rate (GBR) is guaranteed.
If the remaining bandwidth of neighboring cells can meet the preceding requirements for rate,
this feature can be enabled to reduce the power consumption, and therefore increase profits of
operators.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET URNCCELLSHUTDOWNPARA (CME
single configuration: UMTS Radio Global Configuration Express > RNC_Lever
Cell Dynamic ShutDown Parameter Configuration > Cell Dynamic Shutdown
Parameters in RNC; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, set Cell Dynamic ShutDown Switch for
RNC to ON(switch on).
2. Assume that the cell ID is 2003. Run the BSC6900 MML command LST
UCELLDYNSHUTDOWN (CME single configuration: UMTS Cell Configuration
Express > Cell Parameters > Cell Dynamic Shutdown Parameters) to check
whether Cell Dynamic ShutDown Switch is set to ON for this cell.
a. If Cell Dynamic ShutDown Switch is set to OFF, run the BSC6900 MML
command ADD UCELLDYNSHUTDOWN (CME single configuration:
UMTS Cell Configuration Express > Cell Parameters > Cell Dynamic
Shutdown Parameters; CME batch modification center: 3.18 Modifying
UMTS Cell Parameters in Batches). In this step, set Cell Dynamic ShutDown
Switch to ON_1(switch on1), specify First Cell Dynamic ShutDown Interval
Start Time, First Cell Dynamic ShutDown Interval End Time, set Cell
Dynamic ShutDown Type to QOSSHUTDOWN(QosShutDown), and specify
High-Priority Scheduling Indicator.
b. If Cell Dynamic ShutDown Switch is turned on, run the BSC6900 MML
command MOD UCELLDYNSHUTDOWN (CME single configuration:
UMTS Cell Configuration Express > Cell Parameters > Cell Dynamic
Shutdown Parameters; CME batch modification center: 3.18 Modifying
UMTS Cell Parameters in Batches) to modify the settings of the preceding
parameters to the specified settings.
3. Run the BSC6900 MML command LST UINTERFREQNCELL (CME single
configuration: UMTS Cell Configuration Express > Neighboring Cell > Inter-
frequency Neighboring Cell) to check whether cell 2003 is configured with an inter-
frequency co-coverage neighboring cell. Assume that the ID of the inter-frequency
co-coverage neighboring cell is 2004.
a. This feature takes effect only when cell 2004 is under the same NodeB as cell
2003.
b. If the neighboring cell is not configured, run the BSC6900 MML command ADD
UINTERFREQNCELL (CME single configuration: UMTS Cell
Configuration Express > Neighboring Cell > Inter-frequency Neighboring
Cell; CME batch modification center: not supported) to add an inter-frequency
co-coverage neighboring cell. In this step, set Blind Handover Flag to TRUE.
c. If the neighboring cell is configured, run the BSC6900 MML command MOD
UINTERFREQNCELL (CME single configuration: UMTS Cell
Configuration Express > Neighboring Cell > Inter-frequency Neighboring
Cell; CME batch modification center: not supported). In this step, set Blind
Handover Flag set to TRUE.
4. Run the BSC6900 MML command ADD UCELLALGOSWITCH (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Algorithm Switches; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches). In this step, set Cell CAC algorithm switch to
HSDPA_GBP_MEAS(HSDPA GBP Meas Algorithm).
NOTE
This feature takes effect only when the GBP measurement switches of both cell 2003 and cell
2004 are turned on.
l Verification Procedure
1. Start alarm browsing on the BSC6900 LMT.
2. Ensure that the total number of users in cell 2003 and cell 2004 is 0. Alternatively,
add two inter-frequency co-coverage cells that have bidirectional neighboring cell
relationships, and these cells do not carry any services.
3. At a time during the period specified in the BSC6900 MML command ADD
UCELLDYNSHUTDOWN (for example, 09:10):
If the alarm ALM-22202 UMTS Cell Unavailable is reported at cell 2003 with a
cause of cell dynamic shutdown, this feature has been activated.
If the alarm is not reported or is reported at cell 2003 but the cause is not cell
dynamic shutdown, this feature has not been activated.
4. You can also view whether the feature is activated by checking certain counters on
the M2000: If the value of the counter VS.DynOpen.CellSetup is not 0, the feature
is activated; If the value of the counter VS.DynClose.CellDel is not 0, the feature is
not activated.
l Deactivation Procedure
1. Run the BSC6900 MML command SET URNCCELLSHUTDOWNPARA (CME
single configuration: UMTS Radio Global Configuration Express > RNC_Lever
Cell Dynamic ShutDown Parameter Configuration > Cell Dynamic Shutdown
Parameters in RNC; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to deactivate this feature for the RNC. In this step, set Cell
Dynamic ShutDown Switch for RNC to OFF(switch off).
2. Optional: Run the BSC6900 MML command RMV UCELLDYNSHUTDOWN
(CME single configuration: UMTS Cell Configuration Express > Cell
Parameters > Cell Dynamic Shutdown Parameters; CME batch modification
center: not supported). In this step, set Cell ID to 2003 to deactivate this feature for
cell 2003.
----End
Example
/*Activation procedure*/
//Turning on the GBP measurement switches for a cell (cell 2003)and its
inter-frequency co-coverage neighboring cell (cell 2004)
ADD UCELLALGOSWITCH: CellId=2003, NBMCacAlgoSwitch=HSDPA_GBP_MEAS-1,
NBMUlCacAlgoSelSwitch=ALGORITHM_FIRST,
NBMDlCacAlgoSelSwitch=ALGORITHM_FIRST;
2003
RMV UCELLDYNSHUTDOWN: CellId=2003;
This section describes how to activate, verify, and deactivate the optional feature WRFD-020121
Intelligent Power Management.
Prerequisites
l Dependencies on Hardware
Only when DBS3900, BTS3900AL or BTS3900A is used with APM30 and battery.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
With this feature, certain Power Supply Units (PSUs) can be powered on or off according to the
power consumption of the NodeB, reducing the power consumption.
Procedure
l Activation Procedure
1. Run the NodeB MML command SET PSUISS (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Basic Information > Equipment
Management > PSU Intelligent Shutdown Switch; CME batch modification center:
not supported) with the PSU Intelligent Shutdown Switch set to ENABLE
(ENABLE).
l Verification Procedure
1. Run the NodeB MML command LST PSUISS to check whether the PSU Intelligent
Shutdown Switch is set to ENABLE(ENABLE).
l Deactivation Procedure
1. Run the NodeB MML command SET PSUISS (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Basic Information > Equipment
Management > PSU Intelligent Shutdown Switch; CME batch modification center:
not supported) with the PSU Intelligent Shutdown Switch set to DISABLE
(DISABLE).
----End
Example
//Activation procedure
SET PSUISS: PSUISS=ENABLE;
//Verification procedure
LST PSUISS:;
//Deactivation procedure
SET PSUISS: PSUISS=DISABLE;
This section describes how to activate, verify and deactivate the optional feature WRFD-021304
RAN Sharing Introduction Package.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature cannot be used together with the feature WRFD-021311 MOCN
Introduction Package.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature enables multiple operators to share the same set of RAN equipment but have their
own independent cells. The same set of RAN equipment can provide different operators with
rich and differentiated services.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UOPERATORSHARINGMODE (CME
single configuration: UMTS Global Configuration Express > Operator
Configuration > RNC Operators Sharing Mode; CME batch modification center:
not supported). In this step, set RAN Sharing Support to YES to turn on the RAN
sharing switch.
2. Run the BSC6900 MML command ADD UCNOPERATOR (CME single
configuration: UMTS Global Configuration Express > Operator Configuration >
CN Operator; CME batch modification center: not supported) twice to add the
primary and secondary operators respectively.
Primary and secondary operators can have their own OSPs for the same BSC6900.
l Primary and secondary operators can share the same Network ID when required.
l When primary and secondary operators share the same Network ID, they must use the
same OSP code bits but different OSP code[Whole Number].
l When primary and secondary operators do not share Network ID, they can have different
values for OSP code bits.
5. Run the BSC6900 MML command ADD N7DPC (CME single configuration: UMTS
Global Configuration Express > Signaling Configuration > DSP Of DPU; CME
batch modification center: not supported) for multiple times to add DSPs for primary
and secondary operators.
6. Configure Iu data for the primary and secondary operators.
7. Run the BSC6900 MML command ADD UCNNODE (CME single configuration:
UMTS Global Configuration Express > Core Network > UMTS CN Node; CME
batch modification center: not supported) for multiple times to add CN nodes for the
primary operator.
8. Configure Iub data and add a dedicated cell.
NOTE
Example
//Activating RAN Sharing Introduction Package
//Adding a cell
ADD UCELLQUICKSETUP: CELLID=1, CELLNAME="Cell1", BANDIND=BAND1,
PeerIsValid=VALID, PeerCellId=100, CnOpGrpIndex=0, UARFCNUPLINK=9612,
UARFCNDOWNLINK=10562, PSCRAMBCODE=0, TCELL=CHIP256, LAC=H'2501,
SAC=H'0000, CFGRACIND=REQUIRE, RAC=H'00, SpgId = 6, URANUM=D8, URA1=1,
URA2=2, URA3=3, URA4=4, URA5=5, URA6=6, URA7=7, URA8=8,
This section describes how to activate, verify, and deactivate the optional feature
WRFD-02130401 Dedicated Carrier for Each Operator.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The feature WRFD-021304 RAN Sharing Introduction Package has been configured
before this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UOPERATORSHARINGMODE (CME
single configuration: UMTS Global Configuration Express > Operator
Configuration > RNC Operators Sharing Mode; CME batch modification center:
not supported). In this step, set RAN Sharing Support to YES to turn on the RAN
sharing switch.
2. Run the BSC6900 MML command ADD UCNOPERATOR (CME single
configuration: UMTS Global Configuration Express > Operator Configuration >
CN Operator; CME batch modification center: not supported) to add the primary and
secondary operators.
3. Run the BSC6900 MML command ADD UCNOPERGROUP (CME single
configuration: UMTS Global Configuration Express > Operator Configuration >
CN Operator Group; CME batch modification center: not supported) twice to add
an operator group respectively for the primary and secondary operators.
4. Configure Iu data for the primary and secondary operators.
Example
//Activating Dedicated Carrier for Each Operator
This section describes how to activate, verify, and deactivate the optional feature
WRFD-02130402 Flexible Network Architecture.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The configurations of the features on which this feature depends are complete. This
feature depends on the feature WRFD-021304 RAN Sharing Introduction Package.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature can meet the networking requirements of different operators.
Procedure
l Activation Procedure
For information on activating the Iu Flex feature, see 227 Configuring Iu Flex.
For information on activating the Cell Broadcast Service feature, see 70 Configuring Cell
Broadcast Service.
For information on activating the RAN Sharing feature, see 186 Configuring RAN
Sharing Introduction Package.
l Verification Procedure
For information on verifying the Iu Flex feature, see 227 Configuring Iu Flex.
For information on verifying the Cell Broadcast Service feature, see 70 Configuring Cell
Broadcast Service.
For information on verifying the RAN Sharing feature, see 186 Configuring RAN Sharing
Introduction Package.
l Deactivation Procedure
For information on deactivating the Iu Flex feature, see 227 Configuring Iu Flex.
For information on deactivating the Cell Broadcast Service feature, see 70 Configuring
Cell Broadcast Service.
For information on deactivating the RAN Sharing feature, see 186 Configuring RAN
Sharing Introduction Package.
----End
This section describes how to activate, verify, and deactivate the optional feature
WRFD02130403 Mobility Control and Service Differentiation.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The configurations of the features on which this feature depends are complete. This
feature depends on the feature WRFD-021304 RAN Sharing Introduction Package.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature supports the configuration of different service support for multiple operators to meet
their individual requirements.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UOPERATORSHARINGMODE (CME
single configuration: UMTS Global Configuration Express > Operator
Configuration > RNC Operators Sharing Mode; CME batch modification center:
not supported) to set the parameter RAN Sharing Support to YES. Then, set the
parameters Intra RAT Inter Plmn Ho Allowed and Inter RAT Inter Plmn Ho
Allowed to YES.
l Verification Procedure
The cells that belong to different operators can be configured as intra-frequency, inter-
frequency, or inter-RAT neighboring cells.
l Deactivation Procedure
1. Run the BSC6900 MML command SET UOPERATORSHARINGMODE (CME
single configuration: UMTS Global Configuration Express > Operator
Configuration > RNC Operators Sharing Mode; CME batch modification center:
not supported) to set the parameter RAN Sharing Support to YES. Then, set the
parameters Intra RAT Inter Plmn Ho Allowed and Inter RAT Inter Plmn Ho
Allowed to NO.
----End
Example
//Activating Mobility Control and Service Differentiation
SET UOPERATORSHARINGMODE: RANSharingSupport=YES,
InterPlmnHoAllowedIntraRat=YES, InterPlmnHoAllowedInterRat=YES;
//Deactivating Mobility Control and Service Differentiation
SET UOPERATORSHARINGMODE: RANSharingSupport=YES,
InterPlmnHoAllowedIntraRat=NO, InterPlmnHoAllowedInterRat=NO;
This section describes how to activate, verify, and deactivate the optional feature
WRFD-02130404 Independent License Control. (This feature cannot be configured using the
CME. )
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The feature WRFD-021304 RAN Sharing Introduction Package has been configured
before this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature enables operators to have their own network capacity and optional features, thereby
meeting different service and operation requirements.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET LICENSE to configure a license for the
primary operator.
2. Run the BSC6900 MML command SET LICENSE to configure a license for the
secondary operator.
l Verification Procedure
This feature does not need to be verified.
l Deactivation Procedure
Example
//Activating Independent License Control
SET LICENSE: SETOBJECT=UMTS, ISPRIMARYPLMN=YES, CNOPERATORINDEX=0,
CsErlang=30000, FUNCTIONSWITCH1=PDCP-1;
SET LICENSE: SETOBJECT=UMTS, ISPRIMARYPLMN=NO, CNOPERATORINDEX=1,
CsErlang=20000;
This section describes how to activate, verify, and deactivate the optional feature WRFD-021305
RAN Sharing Phase 2.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
The features WRFD-021304 RAN Sharing Introduction Package must be configured
before this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature provides independent Iub transmission resource management for multiple telecom
operators to ensure the QoS of their respective users.
Procedure
l Activation Procedure
For information on activating this feature, see 192 Configuring Dedicated Iub
Transmission Control.
l Verification Procedure
----End
This section describes how to activate, verify, and deactivate the optional feature
WRFD-02130501 Dedicated Iub Transmission Control.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The configurations of the other features, on which this feature depends, are complete.
The feature WRFD-021304 RAN Sharing Introduction Package has been activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature provides separate admission control policies for operators that share the same port,
thereby ensuring the basic bandwidth available for each operator and improving bandwidth
efficiency when the Iub resources are idle.
Procedure
l Activation Procedure
Activating Dedicated Iub Transmission Control in ATM mode
1. Run the BSC6900 MML command ADD OPSEPINFO (CME single
configuration: UMTS Global Configuration Express > Transmission
Resources Configuration > Separate Information for Operators; CME batch
modification center: not supported) to add the separate information for operators,
including the bandwidth admission ratio and load thresholds for each operator, and
set Transport Type to ATM.
NOTE
This feature can be enabled for one to four operators as required. The bandwidth ratios and load
thresholds for these operators need to be separately configured. Note that the sum of the
bandwidth ratios for all valid operators must be 100%.
2. Run the BSC6900 MML command ADD FRALNK (CME single configuration:
NodeB Configuration Express > IUB_RNC > ATM Transport > Fractional
ATM Link; CME batch modification center: not supported), ADD UNILNK
(CME single configuration: NodeB Configuration Express > IUB_RNC > ATM
Transport > UNI Link; CME batch modification center: not supported), or ADD
IMAGRP (CME single configuration: NodeB Configuration Express >
IUB_RNC > ATM Transport > IMA Group; CME batch modification center:
not supported) to add a physical port. Set Operator Separated Flag to ON
(ON). In addition, on the links carried on the physical port, set Index of Separate
Information for Operators.
3. Run the BSC6900 MML command ADD UNODEB (CME single configuration:
Main View > Right Click RNC > Create Logical NodeB; CME batch
modification center: not supported) to add a NodeB. In this step, set Sharing Type
Of NodeB to RANSHARING(RAN Sharing).
4. Run the BSC6900 MML command ADD ADJNODE (CME single configuration:
NodeB Configuration Express > IUB_RNC > ATM Transport > Adjacent
Node; CME batch modification center: not supported) to add an adjacent node.
5. Run the BSC6900 MML command ADD AAL2PATH (CME single
configuration: NodeB Configuration Express > IUB_RNC > ATM Transport
> AAL2 Path; CME batch modification center: not supported) to add an AAL2
path.
6. Run the BSC6900 MML command ADD TRMMAP (CME single configuration:
UMTS Global Configuration Express > Transmission Resources
Configuration > Transport Resource Mapping; CME batch modification
center: not supported) to add a TRM mapping table.
NOTE
The BSC6900 provides a default TRM mapping table. This step is executed only when different
TRM mapping policies are required.
Activating Dedicated Iub Transmission Control in IP mode
1. Run the BSC6900 MML command ADD OPSEPINFO (CME single
configuration: UMTS Global Configuration Express > Transmission
Resources Configuration > Separate Information for Operators; CME batch
modification center: not supported) to add the separate information for operators,
including the bandwidth admission ratio and load thresholds for each operator, and
set Transport Type to IP(IP).
NOTE
This feature can be enabled for one to four operators as required. The bandwidth ratios and load
thresholds for these operators need to be separately configured. Note that the sum of the
bandwidth ratios for all valid operators must be 100%.
2. Run the BSC6900 MML command ADD PPPLNK (CME single configuration:
NodeB Configuration Express > IUB_RNC > IP Transport > PPP Link; CME
batch modification center: not supported) or ADD MPGRP (CME single
configuration: NodeB Configuration Express > IUB_RNC > IP Transport >
MP Group; CME batch modification center: not supported) to add a physical port,
or run the BSC6900 MML command ADD IPLOGICPORT (CME single
configuration: NodeB Configuration Express > IUB_RNC > IP Transport >
IP Logical Port; CME batch modification center: not supported) to add a logical
port. Set Operator Separated Flag to ON(ON), and set Index of Separate
Information for Operators on the links carried on the physical port.
NOTE
If this feature is activated on the physical port, this feature is only enabled on the physical port.
If this feature is activated on the logical port, this feature is only enabled on the logical port. You
can enable this feature on both the physical port and logical port based on the network plan.
3. Run the BSC6900 MML command ADD UNODEB (CME single configuration:
Main View > Right Click RNC > Create Logical NodeB; CME batch
modification center: not supported) to add a NodeB. In this step, set Sharing Type
Of NodeB to RANSHARING(RAN Sharing).
4. Run the BSC6900 MML command ADD ADJNODE (CME single configuration:
NodeB Configuration Express > IUB_RNC > ATM Transport > Adjacent
Node; CME batch modification center: not supported) to add an adjacent node.
5. Run the BSC6900 MML command ADD IPPATH (CME single configuration:
NodeB Configuration Express > IUB_RNC > IP Transport > IP Path; CME
batch modification center: not supported) to add an IP path.
6. Run the BSC6900 MML command ADD TRMMAP (CME single configuration:
UMTS Global Configuration Express > Transmission Resources
Configuration > Transport Resource Mapping; CME batch modification
center: not supported) to add a TRM mapping table.
NOTE
The BSC6900 provides a default TRM mapping table. This step is executed only when different
TRM mapping policies are required.
7. Run the BSC6900 MML command ADD ADJMAP (CME single configuration:
NodeB Configuration Express > IUB_RNC > ATM Transport > Adjacent
Node Mapping; CME batch modification center: not supported) to add the TRM
mapping to the adjacent node. In this step, set Resource Management Mode to
SHARE(Sharing) or EXCLUSIVE(EXCLUSIVE). If you set Resource
Management Mode to EXCLUSIVE(EXCLUSIVE), you are advised to add a
TRM mapping to the adjacent node for each operator. Otherwise, the operator
cannot admit services.
l Verification Procedure
Assume that networks of operators A and B are enabled with the RAN sharing feature.
1. Choose Monitor > Transport Resource RealTime Monitoring on the LMT. Specify
the parameters related to the physical port that is shared by operators A and B and
specify operator indexes. Then, check whether the bandwidth occupied by each
operator meets the conditions specified by the predefined bandwidth ratio parameters.
NOTE
The verification procedures for this feature are the same for the ATM mode and IP mode.
l Deactivation Procedure
Deactivating Dedicated Iub Transmission Control in ATM mode
1. Run the BSC6900 MML command MOD FRALNK (CME single configuration:
NodeB Configuration Express > IUB_RNC > ATM Transport > Fractional
ATM Link; CME batch modification center: not supported), MOD UNILNK
(CME single configuration: NodeB Configuration Express > IUB_RNC > ATM
Transport > UNI Link; CME batch modification center: not supported), or MOD
IMAGRP (CME single configuration: NodeB Configuration Express >
IUB_RNC > ATM Transport > IMA Group; CME batch modification center:
not supported) as required. In this step, set Operator Separated Flag to OFF
(OFF).
Deactivating Dedicated Iub Transmission Control in IP mode
1. If a physical port is added, run the BSC6900 MML command MOD PPPLNK
(CME single configuration: NodeB Configuration Express > IUB_RNC > IP
Transport > PPP Link; CME batch modification center: not supported) or MOD
MPGRP (CME single configuration: NodeB Configuration Express >
IUB_RNC > IP Transport > MP Group; CME batch modification center: not
supported) to set Operator Separated Flag to OFF(OFF); if a logical port is
added, run the BSC6900 MML command MOD IPLOGICPORT (CME single
configuration: NodeB Configuration Express > IUB_RNC > IP Transport >
IP Logical Port; CME batch modification center: not supported) to set Operator
Separated Flag to OFF(OFF).
----End
Example
//Activation procedure
Activate Dedicated Iub Transmission Control in ATM mode
ADD OPSEPINFO: OPSEPINDEX=0, OPCOUNT=TWO, TYPE=ATM, OPINDEX1=0,
BWRATIO1=40, OPINDEX2=3, BWRATIO2=60;
ADD IMAGRP: SRN=0, SN=26, BT=AEUa, IMAGRPN=0, FLOWCTRLSWITCH=ON,
OPSEPFLAG=ON, OPSEPINDEX=0;
ADD UNODEB: NodeBName="NodeB1", NodeBId=1, SRN=0, SN=0, SSN=1,
TnlBearerType=ATM_TRANS, HostType=SINGLEHOST, SharingType=RANSHARING;
ADD ADJNODE: ANI=1, NAME="NodeB1", NODET=IUB, NODEBID=1, TRANST=ATM,
IsROOTNODE=YES, SAALLNKN=20;
ADD AAL2PATH: ANI=1, PATHID=10, CARRYT=ATMLOGICPORT, CARRYF=0,
CARRYSN=26, CARRYVPN=10, VPI=2, VCI=50, TXTRFX=111, RXTRFX=111,
AAL2PATHT=SHARE;
ADD TRMMAP: TMI=14, ITFT=IUB, TRANST=ATM; ADD ADJMAP: ANI=1, ITFT=IUB,
TRANST=ATM, CNMNGMODE=SHARE, TMIGLD=14, TMISLV=14, TMIBRZ=14, FTI=0;
This section describes how to activate, verify, and deactivate the optional feature WRFD-021303
IMSI Based Handover.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
The feature WRFD-021304 RAN Sharing Introduction Package must be configured
before this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
With this feature, configuring SNA-related information on the RNC is supported. This enables
the UTRAN to limit UE mobility when the CN does not support the shared network area (SNA)
function.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET URRCTRLSWITCH (CME single
configuration: UMTS Radio Global Configuration Express > Process Switch
Configuration > Process Switch; CME batch modification center: 3.15 Modifying
RNC Parameters in Batches). In this step, select the
RNCAP_IMSI_HO_SWITCH check box under the parameter
PROCESSSWITCH.
2. Run the BSC6900 MML command ADD ULASNAMAP (CME single configuration:
UMTS Global Configuration Express > Radio Basic Data Configuration >
Mapping of LAC to SNA; CME batch modification center: not supported). In this
step, set PLMN to 46000, LAC to 1234, and SNAC to 1.
3. Run the BSC6900 MML command ADD UIMSISNAMAP (CME single
configuration: UMTS Global Configuration Express > Radio Basic Data
Configuration > Mapping of IMSI to SNA; CME batch modification center: not
supported) to add an IMSI-to-SNA mapping relationship. In this step, set The start of
IMSI to 460071234000000, The end of IMSI to 460071234500000, PLMN to 46000,
and SNAC to 1.
l Verification Procedure
1. Use the UE with the IMSI of 460071234000006 to access the cell with the LAC of
H'1234. The UE is admitted to the cell.
2. Use the UE with the IMSI of 460071234000006 to access the cell with the LAC of
H'1235. The UE is rejected by the cell. In this case, you can view the RRC
CONNECTION REJECT message on the Uu interface.
NOTE
The restrictions on cell update, UTRAN registration area (URA) update, handovers,
relocations, and handling COMMON ID messages are the same as that on RRC connection
request.
l Deactivation Procedure
1. Run the BSC6900 MML command RMV ULASNAMAP (CME single
configuration: UMTS Global Configuration Express > Radio Basic Data
Configuration > Mapping of LAC to SNA; CME batch modification center: not
supported) to remove a mapping relationship between LAC and SNA.
2. Run the BSC6900 MML command RMV UIMSISNAMAP (CME single
configuration: UMTS Global Configuration Express > Radio Basic Data
Configuration > Mapping of IMSI to SNA; CME batch modification center: not
supported) to remove a mapping relationship between IMSI and SNA.
----End
Example
//Activating IMSI-Based Handover
This section describes how to activate, verify, and deactivate the optional feature WRFD-021311
MOCN Introduction Package. (This feature cannot be configured using the CME. )
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature cannot be used together with the feature WRFD-021304 RAN Sharing
Introduction Package.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
Multi-Operator Core Network (MOCN) was introduced in 3GPP Release 6. It enables multiple
operators to share the network and therefore reduces the CAPEX and OPEX.
The MOCN feature has no requirement for the RNC, NodeB, and UE hardware. It is applicable
to all categories of UEs.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command ADD UCNOPERATOR to add a primary
operator. In this step, set Cn Operator Name, MCC, MNC, and Cn Operator
Index to appropriate values.
2. Run the BSC6900 MML command ADD UCNOPERATOR to add a secondary
operator. In this step, set Cn Operator Name, MCC, MNC, and Cn Operator
Index to appropriate values.
3. Run the BSC6900 MML command SET LICENSE to activate the license for the
primary operator.
4. Run the BSC6900 MML command SET LICENSE to activate the license for the
secondary operator.
5. Run the BSC6900 MML command ADD UCNOPERATOR to add a common
operator.
NOTE
If the MOCN operator has applied for a new PLMN, a common operator needs to be configured.
If the MOCN operator does not apply for a new PLMN, a common operator does not need to
be configured.
6. Run the BSC6900 MML command ADD UCNOPERGROUP to add an operator
group.
NOTE
When no common operator is configured, set the common operator index (CnOpIndex1) of the
operator group to the default value 255.
7. Run the BSC6900 MML command SET UOPERATORSHARINGMODE to set
the sharing mode for the operators. Set RAN Sharing Support to NO. Set MOCN
Support to YES. Set Intra RAT Inter Plmn Ho Allowed, Inter RAT Inter Plmn
Ho Allowed, Default CnOperator, and Mocn Control Switch to appropriate values
based on the network plan.
8. Run the BSC6900 MML command SET UOPERATORCFGPARA to set
parameters for the primary operator.
9. Run the BSC6900 MML command SET UOPERATORCFGPARA to set
parameters for the secondary operator.
10. Configure Iu interface transmission data between the BSC6900 and the primary and
secondary operators' CNs by referring to Configuring Interface Data.
11. Run the BSC6900 MML command ADD UCNNODE to add a CN node for the
primary operator.
12. Run the BSC6900 MML command ADD UCNNODE to add a CN node for the
secondary operator.
13. Run the BSC6900 MML command ADD UNRIGLBCNIDMAP to add a mapping
between Network Resource Identifiers (NRIs) and CN nodes.
NOTE
The mapping between NRIs and CN nodes needs to be configured based on the network plan.
If a CN node is configured with multiple NRIs, repeat this step until all the required mapping
relationships are configured.
14. Run the BSC6900 MML command ADD UNODEB to add an MOCN NodeB. In this
step, set Sharing Type Of NodeB to MOCN and set other parameters based on the
network plan.
15. (Optional) Run the BSC6900 MML command ADD UNODEB to add a dedicated
NodeB.
16. Configure the area information by referring to Configuring the Area Information.
NOTE
Location areas must be the same for the primary and secondary operators.
17. Run the BSC6900 MML command ADD UCELLQUICKSETUP to add an MOCN
cell.
NOTE
A cell is a dedicated cell if its operator group is configured with only one operator.
18. Run the BSC6900 MML command ADD UEXT3GCELL to add a neighboring RNC
cell.
l Verification Procedure
1. Register supporting UEs and non-supporting UEs in MOCN cells of the primary and
secondary operators. The UEs are registered successfully and properly initiate CS and
PS services.
NOTE
Deactivating the MOCN feature interrupts services. Therefore, perform the deactivation operations
early in the morning when the traffic is light.
----End
Example
//Configuring MOCN Introduction Package
//Adding the mapping between CN node 10 and an NRI for the primary
operator
ADD UNRIGLBCNIDMAP: CnOpIndex=0, CNId=10, NRI=10;
//Adding the mapping between CN node 20 and an NRI for the primary
operator
ADD UNRIGLBCNIDMAP: CnOpIndex=0, CNId=20, NRI=20;
//Adding the mapping between CN node 11 and an NRI for the secondary
operator
ADD UNRIGLBCNIDMAP: CnOpIndex=1, CNId=11, NRI=100;
//Adding the mapping between CN node 21 and an NRI for the secondary
operator
ADD UNRIGLBCNIDMAP: CnOpIndex=1, CNId=21, NRI=600;
This section describes how to activate, verify, and deactivate the optional feature
WRFD-02131101 Carrier Sharing by Operators.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The feature WRFD-021311 MOCN Introduction Package has been configured before
this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others
The CN supports the MOCN feature.
Context
This feature enables multiple operators to share the same carrier.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command ADD UCELLQUICKSETUP (CME single
configuration: Main View > Right click NodeB > Add UMTS Cell; CME batch
modification center: not supported) to add an MOCN cell so that multiple operators
can share the same carrier.
l Verification Procedure
1. Check whether the MOCN introduction package is effective based on the message
traced on the Uu interface.
If a cell is configured for only one operator, the system information message of
the cell does not contain the information element (IE) multiplePLMN-List.
If a cell is configured with multiple operators but is not configured with a common
operator, the system information message of the cell contains the PLMN of only
the first operator, and the value of the IE multiplePLMN-List is TRUE.
If a cell is configured with multiple operators and a common operator, the system
information message of the cell contains the IE multiplePLMN-List, broadcasting
all PLMNs of the MOCN cell.
As shown in Figure 195-1, the system information message broadcasts PLMN
302580 of the common operator.
As shown in Figure 195-2, the field PLMN Identity in the system information
message contains the IE multiplePLMN-List. This IE contains the PLMNs
(302221 and 302640) of two operators.
The IE Multiple PLMN List contains the PLMNs (302221 and 302640) of the actual
operators.
l Deactivation Procedure
1. Run the BSC6900 MML command RMV UCELL (CME single configuration: Main
View > Right click UMTS cell > Delete Cell; CME batch modification center: not
supported) to remove the MOCN cell.
----End
Example
//Configuring Carrier Sharing by Operators
ADD UCELLQUICKSETUP: PeerIsValid=INVALID, CnOpGrpIndex=0, LAC=H'7208,
SupBmc=FALSE;
//Deactivating Carrier Sharing by Operators
RMV UCELL: CellId=1;
This section describes how to activate, verify, and deactivate the optional feature
WRFD-02131102 Dedicated NodeB/Cell for Operators.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The feature WRFD-021311 MOCN Introduction Package has been configured before
this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature enables operators to independently control a NodeB or cell when the MOCN feature
is enabled.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command ADD UNODEB (CME single configuration:
Main View > Right Click RNC > Create Logical NodeB; CME batch modification
center: not supported) to add a dedicated NodeB.
2. Run the BSC6900 MML command ADD UCELLQUICKSETUP (CME single
configuration: Main View > Right click NodeB > Add UMTS Cell; CME batch
modification center: not supported) to add a dedicated cell.
l Verification Procedure
1. Check whether this feature has been activated based on the master information block
(MIB) message traced on the Uu interface.
As shown in Figure 196-1, the MIB message of the dedicated cell contains the operator
information (302640).
l Deactivation Procedure
1. Run the BSC6900 MML command RMV UCELL (CME single configuration: Main
View > Right click UMTS cell > Delete Cell; CME batch modification center: not
supported) to remove the dedicated cell.
2. Run the BSC6900 MML command MOD UNODEB (CME single configuration:
NodeB Configuration Express > IUB_RNC > NodeB Basic Information >
NodeB; CME batch modification center: not supported) to change a dedicated NodeB
into a shared NodeB.
3. Run the BSC6900 MML command ADD UCELLQUICKSETUP (CME single
configuration: Main View > Right click NodeB > Add UMTS Cell; CME batch
modification center: not supported) to add a shared cell.
----End
Example
//Activating Dedicated NodeB/Cell for Operators
This section describes how to activate, verify, and deactivate the optional feature
WRFD-02131103 MOCN Mobility Management.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The feature WRFD-021311 MOCN Introduction Package has been configured before
this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature is applicable to different MOCN mobility strategies. This feature enables the
BSC6900 to determine whether to hand over a UE to a target cell based on the ID of the operator
to which the UE belongs and the PLMN ID of the target cell.
By default, the BSC6900 allows inter-RAT cross-PLMN handovers. You can prohibit this type
of handover by running the command SET UOPERATORSHARINGMODE (CME single
configuration: UMTS Global Configuration Express > Operator Configuration > RNC
Operators Sharing Mode; CME batch modification center: not supported).
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UOPERATORSHARINGMODE (CME
single configuration: UMTS Global Configuration Express > Operator
Configuration > RNC Operators Sharing Mode; CME batch modification center:
not supported). In this step, set MOCN Support, Intra RAT Inter Plmn Ho
Allowed, and Inter RAT Inter Plmn Ho Allowed to YES.
l Verification Procedure
1. When the cross-PLMN handover switch is turned on, check whether UEs can perform
cross-PLMN handovers, relocations, and cell updates. If UEs can perform cross-
PLMN handovers, relocations, and cell updates, this feature has been activated.
l Deactivation Procedure
1. Run the BSC6900 MML command SET UOPERATORSHARINGMODE (CME
single configuration: UMTS Global Configuration Express > Operator
Configuration > RNC Operators Sharing Mode; CME batch modification center:
not supported). In this step, set MOCN Support to YES, Intra RAT Inter Plmn Ho
Allowed to NO, and Inter RAT Inter Plmn Ho Allowed to NO.
----End
Example
//Activating MOCN Mobility Management
SET UOPERATORSHARINGMODE: RANSharingSupport=NO, MOCNSupport=YES,
InterPlmnHoAllowedIntraRat=YES, InterPlmnHoAllowedInterRat=YES;
//Deactivating MOCN Mobility Management
SET UOPERATORSHARINGMODE: RANSharingSupport=NO, MOCNSupport=YES,
InterPlmnHoAllowedIntraRat=NO, InterPlmnHoAllowedInterRat=NO;
This section describes how to activate, verify, and deactivate the optional feature
WRFD-02131104 MOCN Load Balance.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The feature WRFD-021311 MOCN Introduction Package has been configured before
this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature enables multiple operators to achieve load balance and network fairness.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UOPERATORSHARINGMODE (CME
single configuration: UMTS Global Configuration Express > Operator
Configuration > RNC Operators Sharing Mode; CME batch modification center:
not supported). In this step, set MOCN Support to YES.
NOTE
In this step, set Default CnOperator to 255. The BSC6900 selects operators in Round Robin
mode.
l Verification Procedure
1. Run the BSC6900 MML command LST UOPERATORSHARINGMODE to query
the parameter settings of the feature MOCN Load Balance.
l Deactivation Procedure
1. Run the BSC6900 MML command SET UOPERATORSHARINGMODE (CME
single configuration: UMTS Global Configuration Express > Operator
Configuration > RNC Operators Sharing Mode; CME batch modification center:
not supported). In this step, set MOCN Support to YES and Default CnOperator
to 0. The BSC6900 preferentially selects the default operator (operator 0).
----End
Example
//Activating MOCN Load Balance
SET UOPERATORSHARINGMODE: MOCNSupport=YES, DefaultCnOp=255;
//Deactivating MOCN Load Balance
SET UOPERATORSHARINGMODE: MOCNSupport=YES, DefaultCnOp=0;
This section describes how to activate, verify, and deactivate the optional feature
WRFD-02131106 Routing Roaming UEs in Proportion.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
The feature WRFD-021311 MOCN Introduction Package has been configured before
this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others
The CN supports this feature. During initial registration of a roaming UE, the UE selects
the same operator for CS and PS services, and the IMSI is carried to the RNC.
Context
When roaming UEs of one operator move to the area served by the RNC that is shared among
multiple operators using the Multi-Operator Core Network (MOCN), the RNC routes the UEs
to CN nodes that belong to different operators according to the preset ratio if the UEs are under
the roaming agreement with these operators.
Procedure
l Activation Procedure
NOTE
Assume that operator1 and operator2 share the same RNC by using the MOCN and operator A signs
a roaming agreement with the two operators.
1. To add operator A to the roaming relation list of operator1, run the BSC6900 MML
command ADD UROAMMAP (CME single configuration: UMTS Global
Configuration Express > Operator Configuration > UROAM MAP; CME batch
modification center: not supported). In this step, set MCC for operator A to 460,
MNC to 09, Cn Operator Index for operator1 to 1, Cn Operator Group Index for
operator1 to 1, and Capability of Roaming Operator to an appropriate value
according to the network plan, such as 30.
2. To add operator A to the roaming relation list of operator2, run the BSC6900 MML
command ADD UROAMMAP (CME single configuration: UMTS Global
Configuration Express > Operator Configuration > UROAM MAP; CME batch
modification center: not supported). In this step, set Cn Operator Index for operator2
to 2, Cn Operator Group Index to 1, and Capability of Roaming Operator to an
appropriate value according to the network plan, such as 70.
NOTE
After the parameter settings are complete, the UEs that belong to operator A are distributed to
operator1 and operator2 according to the preset ratio (30:70).
If operator B also signs a roaming agreement with operator1 and operator2, the roaming UE
distribution ratio for operator B must be set to the same as that for operator A when operator
B is added to the roaming relation lists of the two operators.
l Verification Procedure
1. Run the BSC6900 MML command LST UROAMMAP to query the roaming
capacity of operator A. Expected result: Capability of Roaming Operator for
operator1 is set to 30, and Capability of Roaming Operator for operator2 is set to
70.
2. When UEs belonging to operator A roam to the RNC shared by operator1 and
operator2 by using the MOCN for a long measurement period, view the performance
counter VS.ROAM.MOCN.NUM on the M2000. Expected result: The roaming UEs
of operator A are routed to CN nodes of operator1 and operator2 in a preset proportion
of 30:70.
NOTE
UEs of the non-supporting UE type do not support network sharing, as defined in the feature
WRFD-02131101 Carrier Sharing by Operators.
This feature is not applicable to UEs of the supporting UE type (supporting network sharing).
l Deactivation Procedure
1. Run the BSC6900 MML command RMV UROAMMAP (CME single configuration:
UMTS Global Configuration Express > Operator Configuration > UROAM
MAP; CME batch modification center: not supported) to remove operator A from the
roaming relation list of operator1.
2. Run the BSC6900 MML command RMV UROAMMAP (CME single configuration:
UMTS Global Configuration Express > Operator Configuration > UROAM
MAP; CME batch modification center: not supported) to remove operator A from the
roaming relation list of operator2.
----End
Example
/*Activating Routing Roaming UEs in Proportion*/
//Removing operator A serving roaming UEs from the roaming relation list
of operator1
RMV UROAMMAP: MCC="460", MNC="09", CnOpIndex=1, CnOpGrpIndex = 1;
//Removing operator A serving roaming UEs from the roaming relation list
of operator2
RMV UROAMMAP: MCC="460", MNC="09", CnOpIndex=2, CnOpGrpIndex = 1;
This section describes how to activate, verify, and deactivate the optional feature WRFD-140223
MOCN Cell Resource Demarcation.
Prerequisites
l Dependencies on Hardware
Only the 3900 series base stations configured with the WBBPb, WBBPd, or WBBPf
board support this feature.
l Dependencies on Other Features
The feature WRFD-021311 MOCN Introduction Package must be configured before
this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature provides a mechanism for predefining the percentage of cell resources available to
UEs of each operator involved in the MOCN cell. This feature helps prevent the UEs of an
operator from occupying excessive cell resources.
If the MOCN cell has idle resources, the UEs of each operator can use more resources than their
predefined resource percentage. If the MOCN cell is congested, the RNC performs preemption
and congestion control on the operator whose actual resource percentage has exceeded the
predefined value. By doing so, the RNC keeps resource usage of each operator in the MOCN
cell during busy hours close to their respective predefined resource percentage.
You are not advised to use this feature with WRFD-010696 DC-HSDPA. That is because
enabling DC-HSDPA affects power measurement accuracy.
l Precautions
None
l Data Preparation
Scenario 1: Using cell resources based on the HSDPA power percentages for MOCN-
enabled operators in a cell
Parameter Name Parameter ID Setting Source
Description
Scenario 2: Using cell resources based on the R99 SF percentages for MOCN-enabled
operators in a cell
Procedure
l Activation Procedure
Using cell resources based on the HSDPA power percentages for MOCN-enabled
operators in a cell
1. Run the BSC6900 MML command SET URRCTRLSWITCH (CME single
configuration: UMTS Radio Global Configuration Express > Process Switch
Configuration > Process Switch; CME batch modification center: 3.15
Modifying RNC Parameters in Batches). In this step, select
PSCRR_OpIndex_INCLUDED (Switch for carrying operator indexes in the
PHYSICAL SHARED CHANNEL RECONFIGURATION REQUEST
message) under Iub Private Interface Switch to enable the Physical Shared
Channel Reconfiguration Request message to carry the operator index.
2. Run the BSC6900 MML command SET URRCTRLSWITCH (CME single
configuration: UMTS Radio Global Configuration Express > Process Switch
Configuration > Process Switch; CME batch modification center: 3.15
Modifying RNC Parameters in Batches). In this step, select
RL_OpIndex_INCLUDED (Switch for carrying operator indexes in the
RADIO LINK message) under Iub Private Interface Switch to enable the Radio
Link Setup Request message to carry the operator index.
3. Run the BSC6900 MML command MOD UCELLALGOSWITCH (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Algorithm Switches; CME batch modification center: 3.18 Modifying UMTS
Cell Parameters in Batches). In this step, select HSDPA_GBP_MEAS(HSDPA
GBP Meas Algorithm) under Cell CAC algorithm switch to enable the HSDPA
GBP test.
4. Optional: If a neighboring RNC exists, Run the BSC6900 MML command MOD
UNRNC (CME single configuration: IUR Configuration Express >
Neighbouring RNC > Neighboring RNC; CME batch modification center: not
supported). In this step, select PLMNID_INCLUDED (Switch for Carrying
PLMN ID) under Iur Private Interface Switch to turn on the Iur-interface
proprietary IE switch with PLMN ID included.
5. Run the BSC6900 MML command MOD UCELLCAC (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Oriented CAC Algorithm Parameters; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches). In this step, set Non-HSPA
Power Threshold for GBP-based Preemption to according to the network plan.
6. Run the BSC6900 MML command ADD
UCELLMOCNDPAPOWERDEMAR (CME single configuration: UMTS Cell
Configuration Express > Cell Parameters > Cell-Oriented Operator HSDPA
Power Availability Percentage Parameters; CME batch modification center:
3.18 Modifying UMTS Cell Parameters in Batches). In this step, set Cell
Index, Cn Operator Index, and HSDPA Power Availability Percentage to
configure the HSDPA power percentage for an operator of an operator group in a
cell.
7. Run the BSC6900 MML command MOD UCELLALGOSWITCH (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Algorithm Switches; CME batch modification center: 3.18 Modifying UMTS
Cell Parameters in Batches). In this step, select
MOCN_DEMARC_PREEMPT_GBP under Demarcation Preemption
Switch to enable preemption based on HSDPA power percentages of operators in
a cell.
8. Run the BSC6900 MML command ADD UCELLLICENSE (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
License Resource/Function Item; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches). In this step, select
CELL_MOCN_DEMARCATION_SWITCH(Cell MOCN Demarcation
Switch) under Function Switch1 to activate the license for MOCN Cell Resource
Demarcation for operators in a cell.
Using cell resources based on the R99 SF percentages for MOCN-enabled operators in
a cell
1. Run the NodeB MML command SET MACHSPARA (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Radio Layer > Locell Algorithm
Parameters > MAC Parameters > MACHSPARA; CME batch modification center:
3.17 Modifying Physical NodeB Parameters in Batches).In this step, set Resource
Allocate Method to POWERCODE_BAL(Balance between Code and Power).
l Verification Procedure
Using cell resources based on the HSDPA power percentages for MOCN-enabled
operators in a cell
1. Start the Iub-interface message tracing task. Check whether the
NBAP_PHY_SHARED_CH_RECFG_REQ message carries the mOCN-
Operator-Hsdpa-Operator-Index-private IE and the mOCN-Operator-Hsdpa-Pwr-
Ratio-private IE. If yes, the feature based on the HSDPA power percentage has
been activated.
Using cell resources based on the R99 SF percentages for MOCN-enabled operators in
a cell
Example
//Activating MOCN Cell Resource Demarcation
Configuration on the RNC side
Using cell resources based on the HSDPA power percentages for MOCN-enabled
operators in a cell
SET URRCTRLSWITCH: IubPrivateInterfaceSwitch=PSCRR_OpIndex_INCLUDED-1;
SET URRCTRLSWITCH: IubPrivateInterfaceSwitch=RL_OpIndex_INCLUDED-1;
MOD UCELLALGOSWITCH: CellId=0, NBMCacAlgoSwitch=HSDPA_GBP_MEAS-1;
MOD UNRNC: NRncId=1, IurPrivateInterfaceSwitch=PLMNID_INCLUDED-1;
MOD UCELLCAC: CellId=1, NonHPwrForGBPPreemp=40;
ADD UCELLMOCNDPAPOWERDEMAR: CellId=1, CnOpIndex=0, DPAAvaiPwrRatio=10;
MOD UCELLALGOSWITCH: CellId=1,
DemarcPreemptSwitch=MOCN_DEMARC_PREEMPT_GBP-1;
ADD UCELLLICENSE: CellId=1, FuncSwitch1=CELL_MOCN_DEMARCATION_SWITCH-1;
Using cell resources based on the R99 SF percentages for MOCN-enabled
operators in a cell
ADD UCELLMOCNSFDEMAR: CellId=1, CnOpIndex=0, DLAvaiSFRatio=10;
MOD UCELLALGOSWITCH: CellId=1,
DemarcPreemptSwitch=MOCN_DEMARC_PREEMPT_SF-1;
MOD UCELLALGOSWITCH: CellId=1, NBMLdcAlgoSwitch=CELL_CODE_LDR-1;
MOD UCELLALGOSWITCH: CellId=1, NbmSFLdcUeSelSwitch=NBM_SF_LDC_DEMARC;
ADD UCELLLICENSE: CellId=1, FuncSwitch1=CELL_MOCN_DEMARCATION_SWITCH-1;
Configuration on the NodeB side
SET MACHSPARA: LOCELL=0, RSCALLOCM=POWERCODE_BAL;
//Deactivating MOCN Cell Resource Demarcation
MOD UCELLLICENSE: FuncSwitch1=CELL_MOCN_DEMARCATION_SWITCH-0;
This section describes how to activate, verify, and deactivate the optional feature WRFD-021200
HCS (Hierarchical Cell Structure).
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
Based on speed estimation, the BSC6900 hands over fast-moving UEs to low-priority cells to
reduce the number of handovers, and hands over slow-moving UEs to high-priority cells to
increase network capacity.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches).
In this step, set HoSwitch to the following parameter value.
HO_ALGO_HCS_SPEED_EST_SWITCH
HO_INTRA_FREQ_SOFT_HO_SWITCH
HO_INTER_FREQ_HARD_HO_SWITCH
HO_INTER_RAT_PS_OUT_SWITCH
HO_INTER_RAT_CS_OUT_SWITCH
Example
/*Activating HCS (Hierarchical Cell Structure).*/
//Set HandOver Switch
SET UCORRMALGOSWITCH:
HoSwitch=HO_ALGO_HCS_SPEED_EST_SWITCH-1&HO_INTRA_FREQ_SOFT_HO_SWITCH-1&HO
_INTER_FREQ_HARD_HO_SWITCH-1&HO_INTER_RAT_PS_OUT_SWITCH-1&HO_INTER_RAT_CS
_OUT_SWITCH-1, ReservedSwitch0=RESERVED_SWITCH_0_BIT5-0;
//Set HCS cell to Use of HCS
ADD UCELLHCS: CellId=11, UseOfHcs=USED;
//Add an intra-frequency neighboring cell
ADD UINTRAFREQNCELL: RncId=1, CellId=11, NCellRncId=9, NCellId=100,
SIB11Ind=TRUE, IdleQoffset1sn=0, IdleQoffset2sn=0, SIB12Ind=FALSE,
TpenaltyHcsReselect=D0, NPrioFlag=FALSE;
//Add an inter-frequency neighboring cell
ADD UINTERFREQNCELL:RncId=1, CellId=11, NCellRncId=9, NCellId=100,
CIOOffset=0, SIB11Ind=TRUE, SIB12Ind=FALSE, TpenaltyHcsReselect=D0,
HOCovPrio=1, BlindHOFlag=FALSE, NPrioFlag=FALSE;
//Add a GSM inter-RAT neighboring cell
ADD U2GNCELL: RncId=1, CellId=11, GSMCellIndex=0, CIOOffset=0,
Qoffset1sn=0, Qrxlevmin=-50, TpenaltyHcsReselect=D0, TempOffset1=D3,
BlindHoFlag=TRUE, BlindHOPrio=30, NPrioFlag=FALSE;
//Set Algorithm Switch for UE Speed Estimation
ADD UCELLHCSHO: CellId=11, SpdEstSwitch=ON;
//Deactivating HCS (Hierarchical Cell Structure).
SET UCORRMALGOSWITCH: HoSwitch=HO_ALGO_HCS_SPEED_EST_SWITCH-0;
MOD UCELLHCS: CellId=11, UseOfHcs=NOT_USED;
MOD UCELLHCSHO: CellId=11, SpdEstSwitch=OFF;
This section describes how to activate, verify, and deactivate the optional feature WRFD-020111
One Tunnel.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others
The SGSN, GGSN and S-GW need to support the feature One Tunnel.
The control plane of the Iu-PS interface has been configured. For details in IP pool
networking, see Configuring the Control Plane of the Iu-PS Interface (over IP), For
details in IP path networking, see Configuring the Control Plane of the Iu-PS Interface
(over Transmission Resource Pool).
Context
The feature One Tunnel is available between the RNC and the GGSN and between the RNC and
the S-GW. This feature improves the efficiency of processing PS traffic and prevents the
capabilities of the SGSN from becoming the bottleneck under heavy PS traffic. The network
plan specifies which tunnel to be configured.
NOTE
l In IP pool networking, you do not need to activate or deactivate this feature. Related configurations are
included in initial configuration. IP pool networking does not consider whether the peer NE is the SGSN,
GGSN, or S-GW. Instead, only an Iu-PS adjacent node needs to be configured. This operation is mandatory
in the section that describes how to configure user-plane data over the Iu-PS interface in BSC6900 UMTS
Initial Configuration Guide. For details, see Configuring the User Plane of the Iu-PS Interface (over
Transmission Resource Pool).
l In IP path networking, this feature needs to be configured. This section describes about how to activate and
deactivate this feature.
l Precautions
You are advised to configure this feature during off-peak hours because configuring
this feature involves transmission mode reconfiguration which interrupts services.
l Data Preparation
Parameter Name Parameter ID Setting Source
Description
Procedure
l Activation Procedure
1. Run the MML command ADD ADJNODE (CME single configuration: IUPS
Configuration Express > IP Transport > Adjacent Node; CME batch modification
center: not supported) to add basic information about the adjacent nodes. In this step,
set parameters as follows:
Set Adjacent Node Type to IUPS so that the node type is set to Iu PS.
Set Transport Type to IP so that the transport type is IP.
Set SGSN FLAG to NO. Depending on the configured adjacent node, set the
parameter to GGSN or S-GW.
2. Run the MML command ADD IPPATH (CME single configuration: IUPS
Configuration Express > IP Transport > IP Path; CME batch modification center:
not supported) to add an IP path. In this step, set the PEERIPADDR parameter to the
IP address of the GGSN or S-GW.
3. Optional: If layer 3 networking is deployed between the BSC6900 and the peer node,
run the MML command ADD IPRT (CME single configuration: IUPS
Configuration Express > IP Transport > IP Route; CME batch modification center:
not supported) to add an IP path.
NOTE
l On the SGSN, GGSN, or S-GW side, you can run associated commands to check whether the
feature One Tunnel is supported.
l Verification Procedure
1. On the BSC6900 LMT, start signaling tracing over the Iu interface. For details, see
Tracing Messages on the Iu Interface.
l Deactivation Procedure
1. Run the MML command RMV ADJNODE (CME single configuration: IUPS
Configuration Express > IP Transport > Adjacent Node; CME batch modification
center: not supported) to remove the corresponding adjacent node.
----End
Example
//Activation procedure:
//Adding an adjacent node
ADD ADJNODE: ANI=0, NAME="S-GW NAME", NODET=IUPS, TRANST=IP, ISIPPOOL=NO,
SGSNFLG=NO;
/Adding an IP path for the adjacent node
ADD IPPATH: ANI=0, PATHID=1, ITFT=IUPS, PATHT=BE, IPADDR="80.1.1.1",
PEERIPADDR="10.161.0.1", PEERMASK="255.255.255.0", TXBW=1000, RXBW=1000;
//Adding a layer 3 route to this adjacent node
ADD IPRT: SRN=0, SN=14, DSTIP="10.161.0.1", DSTMASK="255.255.255.0",
NEXTHOP="80.1.1.10", PRIORITY=HIGH, REMARK="TO S-GW ROUTE";
//Deactivation procedure:
RMV ADJNODE: ANI=0;
This section describes how to activate, verify, and deactivate the optional feature WRFD-050405
Overbooking on ATM Transmission.
Prerequisites
l Dependencies on Hardware
The backpressure and VP shaping mechanism depends on the ATM interface board on
RNC like AOUa/UOIa/AEUa/AOUc/UOIc.
The BTS3902E cannot support this feature.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature improves the resource usage and provides a method for greatly saving OPEX on
ATM transmission, especially on Iub interface, when deploying HSDPA services. Other
strategies applied in overbooking are as follows:
l RLC retransmission rate-based downlink congestion control
l Backpressure-based downlink congestion control
l VP shaping
Procedure
l Activation Procedure
Activating RLC retransmission rate-based downlink congestion control
Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express > Connection_Oriented
RRM Switch Configuration > Connection Oriented Algorithm Switches; CME
1. On the BSC6900 LMT, start downlink traffic and bandwidth tracing tasks on the Uu,
Iub, and Iu interfaces.
2. Register an R99 user UE1 in the HLR. Enable UE1 with streaming services and with
both highest uplink rate and highest downlink rate of 384 kbit/s.
3. Register an HSDPA user UE2 in the HLR. Enable UE2 with background services and
with highest uplink rate of 384 kbit/s and highest downlink rate of 1450 kbit/s.
4. Run the BSC6900 MML command ADD TRMMAP to map R99 services to the high-
priority queue and HSDPA services to the low-priority queue.
5. All AAL2 paths of the RNC are carried on an IMA port (IMA port is configured to
1Mbit/s). Enable the port flow control when adding the IMA port.
6. Enable UE1 and UE2 to stay in idle mode and camp on the test cell. The test cell must
support HSDPA services.
7. Use UE1 to perform PS streaming services, that is, use UE1 to download files from
the FTP server.
Expected result: The IMA port is not congested and UE1 downloads data at the highest
rate.
8. Use UE2 to perform PS BE services, that is, use UE2 to download files from the FTP
server.
Expected result: The IMA port is congested and the backpressure function is triggered.
The downloading rate of UE2 decreases and that of UE1 remains unchanged. This is
because R99 services have a higher priority.
l Deactivation Procedure
Deactivating RLC retransmission rate-based downlink congestion control
Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express > Connection_Oriented
RRM Switch Configuration > Connection Oriented Algorithm Switches; CME
batch modification center: 3.15 Modifying RNC Parameters in Batches) to turn off
the flow control switch.
For R99 BE services, deselect DRA_R99_DL_FLOW_CONTROL_SWITCH in
Dynamic Resource Allocation Switch.
For HSDPA BE services, deselect
DRA_HSDPA_DL_FLOW_CONTROL_SWITCH in Dynamic Resource
Allocation Switch.
Deactivating backpressure-based downlink congestion control
1. Run the BSC6900 MML command MOD IMAGRP (CME single configuration:
NodeB Configuration Express > IUB_RNC > ATM Transport > IMA
Group; CME batch modification center: not supported). In this step, set Flow
control switch to OFF.
2. Run the BSC6900 MML command MOD UNILNK (CME single configuration:
NodeB Configuration Express > IUB_RNC > ATM Transport > UNI Link;
CME batch modification center: not supported). In this step, set Flow control
switch to OFF.
3. Run the BSC6900 MML command MOD FRALNK (CME single configuration:
NodeB Configuration Express > IUB_RNC > ATM Transport > Fractional
ATM Link; CME batch modification center: not supported). In this step, set Flow
control switch to OFF.
4. Run the BSC6900 MML command MOD ATMLOGICPORT (CME single
configuration: NodeB Configuration Express > IUB_RNC > ATM Transport
> ATM Logical Port; CME batch modification center: not supported). In this step,
set Flow control switch to OFF.
----End
Example
//Activating RLC retransmission rate-based downlink congestion control
SET UCORRMALGOSWITCH:
DraSwitch=DRA_HSDPA_DL_FLOW_CONTROL_SWITCH-1&DRA_R99_DL_FLOW_CONTROL_SWIT
CH-1;
//Activating VP shaping
ADD ATMLOGICPORT: SRN=1, SN=14, LPNTYPE=Leaf, BT=AOUc, LPN=0,
CARRYT=ATMLOGICPORT, UPPERVP=0, TXBW=512, RXBW=512, FLOWCTRLSWITCH=ON;
ADD AAL2PATH: ANI=0, PATHID=1, CARRYT=ATMLOGICPORT, CARRYF=0, CARRYSN=0,
CARRYVPN=0, VPI=0, VCI=200, TXTRFX=150, RXTRFX=150, AAL2PATHT=HSPA;
This section describes how to activate, verify, and deactivate the optional feature WRFD-050105
ATM Switching-Based Hub NodeB.
Prerequisites
l Dependencies on Hardware
The BTS3902E cannot support this feature.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
Context
This feature enables NodeB to provide the transmission convergence function in ATM mode.
Thus, the convergence gain is achieved and the transmission line cost is reduced.
Procedure
l Activation Procedure
1. Run the NodeB MML command ADD TREELNKPVC (CME single configuration:
NodeB Configuration Express > IUB_NodeB > ATM Transport Layer >
NetWork > TreeLink PVC; CME batch modification center: not supported) to add
a tree link PVC.
l Verification Procedure
1. Run the NodeB MML command LST TREELNKPVC to query the tree link PVC.
l Deactivation Procedure
1. Run the NodeB MML command RMV TREELNKPVC (CME single configuration:
NodeB Configuration Express > IUB_NodeB > ATM Transport Layer >
NetWork > TreeLink PVC; CME batch modification center: not supported) to
remove the tree link PVC.
----End
Example
l NodeB V200R014
//Activation procedure
ADD TREELNKPVC: NO=1, JNRSCGRP=DISABLE, VST=VC_SWITCH, SRCSRN=0,
SRCSN=7, SRCSBT=BASE_BOARD,
SRCPT=IMA, SRCPN=0, SRCVPI=7, SRCVCI=33, DSTSRN=0, DSTSN=5,
DSTSBT=E1_COVERBOARD, DSTPT=IMA,
DSTPN=1, DSTVPI=8, DSTVCI=33, RU=kbps, ST=RTVBR, PCR=1000, SCR=800;
//Verification procedure
LST TREELNKPVC:;
//Deactivation procedure
RMV TREELNKPVC: NO=1;
l NodeB V100R014
//Activation procedure
ADD TREELNKPVC: NO=1, VST=VC_SWITCH, SRCSRN=0, SRCSN=15,
SRCSBT=BASE_BOARD,
SRCPT=IMA, SRCPN=0, SRCVPI=7, SRCVCI=33, DSTSRN=0, DSTSN=12,
DSTSBT=E1_COVERBOARD, DSTPT=IMA,
DSTPN=1, DSTVPI=8, DSTVCI=33, RU=KBPS, ST=RTVBR, PCR=1000, SCR=800;
//Verification procedure
LST TREELNKPVC:;
//Deactivation procedure
RMV TREELNKPVC: NO=1;
This section describes how to activate, verify, and deactivate the optional feature WRFD-050106
AAL2 Switching-Based Hub NodeB.
Prerequisites
l Dependencies on Hardware
DBS 3800 does not support this feature.
BTS 3902E does not support this feature.
l Dependencies on Other Features
The feature WRFD-050105 ATM Switching-Based Hub NodeB must be configured
before this feature is activated.
l License
This feature is not under license control.
Context
This feature enables Huawei NodeB to provide the AAL2 transmission convergence function
in ATM mode. Thus, the convergence gain is achieved and the transmission line cost is reduced.
Procedure
l Activation Procedure
1. Run the NodeB MML command ADD AAL2NODE (CME single configuration:
NodeB Configuration Express > IUB_NodeB > ATM Transport Layer >
ALCAP > AAL2 Node; CME batch modification center: 3.17 Modifying Physical
NodeB Parameters in Batches) to add an AAL2 node. In this step, set Node Type
to HUB(Switching Node).
2. Run the NodeB MML command ADD AAL2ADJNODE (CME single configuration:
NodeB Configuration Express > IUB_NodeB > ATM Transport Layer >
ALCAP > AAL2 Adjacent Node; CME batch modification center: not supported) to
add an AAL2 adjacent node to the lower-level NodeB.
l Verification Procedure
1. Run the NodeB MML command DSP AAL2NODE to query the configuration of the
AAL2 node.
2. Run the NodeB MML command DSP AAL2ADJNODE to query the configuration
of the AAL2 adjacent node.
l Deactivation Procedure
1. Run the NodeB MML command RMV AAL2ADJNODE (CME single
configuration: NodeB Configuration Express > IUB_NodeB > ATM Transport
Layer > ALCAP > AAL2 Adjacent Node; CME batch modification center: not
supported) to remove the AAL2 adjacent node.
2. Run the NodeB MML command RMV AAL2NODE (CME single configuration:
NodeB Configuration Express > IUB_NodeB > ATM Transport Layer >
ALCAP > AAL2 Node; CME batch modification center: not supported) to remove
an AAL2 node. In this step, set Node Type to HUB(Switching Node).
NOTE
There is a relation between the AAL2 adjacent node and the AAL2 node. Therefore, you need
to remove the AAL2 adjacent nodes first and then remove the AAL2 node. Note that the AAL2
node can be removed only after all the AAL2 adjacent nodes are removed. Otherwise, the
command execution fails.
----End
Example
//Activation procedure
ADD AAL2NODE: NT=HUB, LN=1;
ADD AAL2ADJNODE: ANI=1,
ADDR="H'3912323232323232333333333333333333333333", LN=2;
//Verification procedure
DSP AAL2NODE:;
DSP AAL2ADJNODE:;
//Deactivation procedure
RMV AAL2ADJNODE: ANI=1;
RMV AAL2NODE: NT=HUB;
This section describes how to activate, verify, and deactivate the optional feature WRFD-050402
IP Transmission Introduction on Iub Interface. (This feature cannot be configured using the
CME. )
Prerequisites
l Dependencies on Hardware
To use the IP header compression function on the Iub interface, the PEUa or POUa
board is required.
Only the Dopra Linux OS supports the built-in firewall function for O&M.
Only the FG2c and GOUc boards of the BSC6900 support the built-in firewall function
for interfaces.
Only the FG2a, GOUa, FG2c and GOUc boards of the BSC6900 support Bidirectional
Forwarding Detection (BFD).
Dependencies on base stations:
NUTI board is needed with BTS3812E/AE to support this feature.
Only the 3900 series NodeB supports inter-board ML-PPP.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature provides a new lub transmission solution for operators. Compared with ATM
transmission, IP transmission reduces the transmission costs of HSDPA and HSUPA services.
This feature enhances Iub transmission by introducing the following functions: BFD-based IP
fault detection, built-in firewall on the RNC side, and built-in firewall on the NodeB side.
l If BFD-based IP fault detection is enabled, the BSC6900 triggers a port switchover, board
switchover, or IP rerouting when detecting that the gateway or the peer entity becomes
faulty. BFD can be classified into multi-hop BFD and single-hop BFD:
In multi-hop BFD, the IP addresses of the local and peer ports must be on different
network segments.
In single-hop BFD, the IP addresses of the local and peer ports must be on the same
network segment.
l The built-in firewall on the RNC side safeguards IP Ethernet ports on interface boards and
O&M ports against network attacks.
l The built-in firewall on the NodeB side safeguards the Iub interface against network attacks
during IP transmission.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET ETHPORT to set the attributes of an
Ethernet port. In this step, takes the FG2c board as an example.
2. Run the BSC6900 MML command ADD ETHIP to add an IP address to the Ethernet
port.
3. Run the BSC6900 MML command STR IPCHK to configure the BFD check. In this
step, set Check type to SBFD.
4. Run the BSC6900 MML command SET IPGUARD to configure the built-in firewall
function for an interface board. In this step, set Board type. to FG2c and ARP
Learning Strict Switch to ON.
NOTE
The FG2c and GOUc boards support both the invalid packet detection function and the ARP learning
strict function. The FG2a and GOUa boards support only the ARP learning strict function.
5. (Optional) Activate the built-in firewall function for O&M (only the Dopra Linux OS
supports the built-in firewall function) by performing the following operations: Log
in to the OMU through LMT locally or through Putty remotely. Run the Dopra Linux
command iptables -A INPUT -s restricted IP -i Ethernet adapter -p transport
protocol --dport restricted port -j DROP. Here, restricted IP refers to the IP address
that needs to be prohibited or allowed, and it can be a single IP address or a network
segment; Ethernet adapter is the name of the OMU external Ethernet adapter; transport
protocol can be TCP or UDP; restricted port is the port to be prohibited. If -p transport
protocol and --dport restricted port are not specified, all ports are disabled.
6. Run the BSC6900 MML command ADD PPPLNK to configure head compress for
a PPP link. In this step, set Head compress to UDP/IP_HC(UDP/IP_HC). Run the
BSC6900 MML command ADD MPGRP to configure head compress for a PPP link
group. In this step, set Head compress to UDP/IP_HC(UDP/IP_HC).
NOTE
Head compress must be configured on peer equipment.
7. Run the NodeB MML command ADD PPPLNK to enable head compress for a PPP
link. Run the NodeB MML command ADD MPGRP to enable head compress for a
PPP link group.
8. Activating the built-in firewall function on the NodeB.
a. Run the NodeB MML command ADD ACL to add an access control list (ACL).
b. Run the NodeB MML command ADD ACLRULE to add a rule to the ACL.
NOTE
Before adding a rule to an ACL, ensure that the ACL has already existed.
c. Run the NodeB MML command ADD PACKETFILTER to bind an ACL to a
port so that packets received at the port are filtered by the ACL.
9. Optional: Activating layer 2 ACL packet filter.
a. Run the NodeB MML command ADD ACL to add an access control list (ACL).
b. Run the NodeB MML command ADD ACLRULE to add a rule to the ACL.
NOTE
The ACL used in layer 2 packet filter is an extended ACL. According to the ACL
specifications, the ID of an extended ACL ranges from 4000 to 4999. Therefore, the ACL
ID configured in layer 2 ACL packet filter must also range from 4000 to 4999.
c. Run the NodeB MML command ADD PACKETFILTER to bind an ACL to a
port so that packets received at the port are filtered by the ACL.
10. Optional: Run the NodeB MML command ADD FLOODDEFEND to activate flood
attack prevention.
11. Optional: Run the NodeB MML command SET IPGUARD to activate ARP spoofing
prevention.
l Verification Procedure
1. Run the BSC6900 MML command DSP ETHPORT to query the attributes of an
Ethernet port.
2. Run the BSC6900 MML command LST ETHIP to query the IP address of the
Ethernet port.
3. Run the BSC6900 MML command DSP IPCHK to query whether the Check state
is UP.
4. Start BFD-based IP fault detection. If a BFD fails, an alarm ALM-21346 IP
Connectivity Check Failure is reported.
5. Run the BSC6900 MML command LST IPGUARD to check whether the value of
ARP Learning Strict Switch is ON.
6. Built response messages to ARP requests and sent to interface boards. Run the
BSC6900 MML command DSP ARP to query the ARP table of interface boards. If
the information of interface boards in ARP table do not update, the ARP Learning
Strict Switch is valid.
7. If any invalid packet exists, run the BSC6900 MML command DSP
INVALIDPKTINFO to query the detailed information.
8. (Optional) Log in to the computer whose IP address is prohibited and check whether
the prohibited services can be performed. Run the Dopra Linux command iptables -
L. All the filtering rules on the OMU will be listed, and check whether new rules are
added successfully.
If port 80 is disabled, logging in to the BSC6900 LMT is prohibited. Check whether
you can log in to the BSC6900 LMT on the PC whose port 80 is disabled.
If port 22 is disabled, the OMU cannot be logged in to remotely. Check whether
you can log in to the BSC6900 OMU through Putty on the PC whose port 22 is
disabled.
If port 21 is disabled, FTP services of the OMU cannot be used. Check whether
you can connect to the FTP server of the BSC6900 OMU through an FTP client
on the PC whose port 21 is disabled.
9. Run the BSC6900 MML command DSP PPPLNK or DSP MPGRP to query whether
the Code compress type is UDP/IP_HC.
10. Run the NodeB MML command DSP PPPLNK or DSP MPGRP to check whether
the compress state is enable.
11. Run the NodeB MML command LST ACL to check whether an ACL has been
configured.
12. Run the NodeB MML command LST ACLRULE to check whether a rule has been
added to the ACL.
13. Run the NodeB MML command DSP PACKETFILTER to check whether a port is
bound to the ACL.
14. Run the NodeB MML command PING to use IP addresses that are not listed in the
ACL to ping the port supporting the packet filtering function. If no response is
received, the built-in firewall on the NodeB side has been activated.
15. Optional: To check whether layer 2 ACL packet filter has been activated, Run the
NodeB MML command DSP PACKETFILTER to query the junk packets that have
been filtered out.
16. Optional: To check whether flood attack prevention has been activated, Run the
NodeB MML command DSP FLOODDEFEND to query the discarded attack
packets.
17. Optional: To check whether malformed packet attack prevention and ARP spoofing
prevention have been activated, Run the NodeB MML command DSP
INVALIDPKTINFO to query the discarded attack packets.
l Deactivation Procedure
1. Run the BSC6900 MML command STP IPCHK to stop the BFD.
2. Run the BSC6900 MML command SET IPGUARD. In this step, set Board type to
FG2c and ARP Learning Strict Switch to OFF.
3. Run the BSC6900 MML command RMV ETHIP to remove an IP address from the
Ethernet port.
4. Run the BSC6900 MML command SET ETHPORT. In this step, set Port type to
FE.
5. (Optional) Log in to the OMU through the LMT locally or through Putty remotely.
Run the Dopra Linux command iptables -D INPUT -s restricted IP -i Ethernet
adapter -p transport protocol --dport restricted port -j DROP. Here, restricted IP
is the IP address that needs to be prohibited or allowed, and it can be a single IP address
or a network segment; Ethernet adapter is the name of the OMU external Ethernet
adapter; transport protocol can be TCP or UDP; restricted port is the port to be
prohibited, and it is used together with the transport protocol. If -p transport protocol
and --dport restricted port are not specified, all ports are disabled.
6. (Optional) Run the Dopra Linux command iptables -L. All the filtering rules on the
OMU will be listed, and check whether new rules are removed successfully.
7. Run the BSC6900 MML command MOD PPPLNK or MOD MPGRP. In this step,
set Head compress to No_HC.
8. Run the NodeB MML command RMV PPPLNK to remove a PPP link. Run the
NodeB MML command RMV MPGRP to remove a PPP link group.
9. Run the NodeB MML command RMV PACKETFILTER to remove the binding
relationship between the port and the ACL.
10. Run the NodeB MML command RMV ACLRULE to remove all the rules from the
ACL.
11. Run the NodeB MML command RMV ACL to remove the ACL.
12. Optional: Run the NodeB MML command RMV PACKETFILTER to deactivate
layer 2 ACL packet filter for a port.
13. Optional: Run the NodeB MML command RMV FLOODDEFEND to deactivate
flood attack prevention.
14. Optional: Run the NodeB MML command SET IPGUARD with ARP Spoofing
Check Switch and ARP Learning Strict Switch set to DISABLE(Disable) to
deactivate ARP spoofing prevention.
----End
Example
//Configuring the attributes of an Ethernet port and adding an IP address
to the port
SET ETHPORT: SRN=0, SN=14, BRDTYPE=FG2c, PTYPE=GE, SPEED=AUTO;
ADD ETHIP: SRN=0, SN=14, PN=0, IPINDEX=0, IPADDR="10.171.35.123",
MASK="255.255.255.0";
//Activating BFD-based IP fault detection on an interface board
STR IPCHK: SRN=0, SN=14, CHKTYPE=SBFD, CARRYT=ETHPORT, PN=0,
PEERIP="10.171.35.126";
//Activating the built-in firewall function on an RNC interface board
SET IPGUARD: SRN=0, SN=14, BRDTYPE=FG2c, ARPLRNSTRICTSW=ON;
//Activating the built-in firewall function for O&M on the RNC
//For example, only the IP addresses on the 10.141.148.0 network segment
is allowed to access the LMT
iptables -A INPUT -s ! 10.141.148.0/255.255.255.0 -i bond1 -p tcp --dport
80 -j DROP
//Activating IP head compress for a PPP link
ADD PPPLNK: SRN=0, SN=14, BRDTYPE=PEUa, LGCAPPTYPE=IP, PPPLNKN=0, DS1=0,
TSBITMAP=TS1-1, BORROWDEVIP=NO, LOCALIP="5.5.5.5", MASK="255.255.255.0",
PEERIP="5.5.5.6", IPHC=UDP/IP_HC, PPPMUX=Disable, AUTHTYPE=NO_V,
FLOWCTRLSWITCH=ON, ERRDETECTSW=OFF, OPSEPFLAG=OFF;
//Activating IP head compress for a PPP link group
ADD MPGRP: SRN=0, SN=14, BRDTYPE=PEUa, LGCAPPTYPE=IP, MPGRPN=0,
MPTYPE=MCPPP, BORROWDEVIP=NO, LOCALIP="5.5.5.5", MASK="255.255.255.0",
PEERIP="5.5.5.6", MHF=LONG, PPPMUX=Disable, FLOWCTRLSWITCH=ON,
AUTHTYPE=NO_V, ERRDETECTSW=OFF, ANTIERRFLAG=OFF, OPSEPFLAG=OFF;
//Activating IP head compress for a PPP link on NodeB
ADD PPPLNK: SRN=0, SN=0, SBT=E1_COVERBOARD, AUTH=NONAUTH, TSN=TS1-1,
IPHC=ENABLE;
//Activating IP head compress for a PPP link group on NodeB
ADD MPGRP: SRN=0, SN=0, SBT=E1_COVERBOARD, AUTH=NONAUTH, IPHC=ENABLE;
//Activating the built-in firewall function on the NodeB
ADD ACL: ACLID=3000, ACLDESC="ACL_TEST";
ADD ACLRULE: ACLID=3000, RULEID=1, PT=IP, SIP="192.168.1.1",
SWC="0.0.0.0", DIP="10.10.1.101", DWC="0.0.0.0", MDSCP=NO;
ADD PACKETFILTER: SRN=0, SN=7, SBT=BASE_BOARD, PT=ETH, PN=0, ACLID=3000;
//(Optional)Activating layer 2 ACL packet filter
ADD ACL: ACLID=4000, ACLDESC="Acl Group is created";
ADD ACLRULE: ACLID=4000, VLANIDOP=OP_RANGE, VLANID1=100, VLANID2=105;
ADD PACKETFILTER: SRN=0, SN=7, SBT=BASE_BOARD, PT=ETH, PN=0, FM=L2_ACL,
ACLID2=4000;
//(Optional)Activating flood attack prevention
This section describes how to activate, verify and deactivate the optional feature WRFD-050403
Hybrid Iub IP Transmission.
Prerequisites
l Dependencies on Hardware
BTS3902E does not support this feature.
l Dependencies on Other Features
The configurations of the features on which this feature depends are complete. This
feature depends on the feature WRFD-050402 IP Transmission Introduction on Iub
Interface.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others
The RNC and NodeB support IP transmission.
The control-plane data and physical device data of the IP-based Iub interface is
configured.
Context
In hybrid IP transmission, real-time services and non-real-time services are transmitted on
discrete paths to meet different requirements of services in the UMTS system. Two types of
hybrid transmission are available: FE+E1/T1 and FE+FE.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command ADD UNODEB (CME single configuration:
Main View > Right Click RNC > Create Logical NodeB; CME batch modification
center: not supported) to add a NodeB. In this step, set IUB Trans Bearer Type to
HYBRID_IP_TRANS.
2. Run the BSC6900 MML command ADD ADJNODE (CME single configuration:
NodeB Configuration Express > IUB_RNC > IP Transport > Adjacent Node;
CME batch modification center: not supported) to add an adjacent node. In this step,
set the parameter Adjacent Node Type to IUB and the parameter Transport Type
to HYBIRD_IP.
3. Run the BSC6900 MML command ADD IPPATH (CME single configuration:
NodeB Configuration Express > IUB_RNC > IP Transport > IP Path; CME batch
modification center: not supported) to add an IP path. In this step, set the parameter
Interface Type to IUB and the parameter Transport Type to HYBIRD_IP.
NOTE
If IP Path Type is set to QOS or BE-EF, the path is a high-priority path and usually E1/T1
transmission is applied.
If IP Path Type is set to LQ_QOS or LQ_BE-LQ_EF, the path is a low-priority path and usually
FE transmission is applied.
4. Run the BSC6900 MML command ADD TRMMAP (CME single configuration:
UMTS Global Configuration Express > Transmission Resources Configuration
> Transport Resource Mapping; CME batch modification center: not supported).
In this step, set Interface Type to IUB and Transport Type to HYBIRD_IP.
5. Run the BSC6900 MML command ADD ADJMAP (CME single configuration:
NodeB Configuration Express > IUB_RNC > IP Transport > Adjacent Node
Mapping; CME batch modification center: not supported). In this step, set Interface
Type to IUB, and Transport Type of the adjacent node and interface type and
Interface type to HYBIRD_IP.
l Verification Procedure
1. Use the UE to make a call. If the call is connected, you can infer that high-priority
services can access the high-priority IP paths normally and low-priority services can
access the low-priority IP paths normally.
2. Run the BSC6900 MML command DSP IPCHN to query the type of services carried
in the IP path, and the forward bit rate and backward bit rate of the services.
l Deactivation Procedure
1. Run the BSC6900 MML command RMV ADJMAP (CME single configuration:
NodeB Configuration Express > IUB_RNC > IP Transport > Adjacent Node
Mapping; CME batch modification center: not supported) to remove the TRM
mapping to the adjacent node on the Iub interface.
2. Run the BSC6900 MML command RMV TRMMAP (CME single configuration:
UMTS Global Configuration Express > Transmission Resources Configuration
> Transport Resource Mapping; CME batch modification center: not supported) to
remove the transmission resource mapping on the Iub interface.
3. Run the BSC6900 MML command RMV IPPATH (CME single configuration:
NodeB Configuration Express > IUB_RNC > IP Transport > IP Path; CME batch
modification center: not supported) to remove the IP path on the Iub interface.
----End
Example
//Activating Hybrid Iub IP Transmission
//Adding a NodeB
This section describes how to activate, verify, and deactivate the optional feature WRFD-050404
ATM/IP Dual Stack NodeB.
Prerequisites
l Dependencies on Hardware
BSC6900 is configured with both ATM interface boards and IP interface boards.
BTS3902E does not support this feature.
l Dependencies on Other Features
The feature WRFD-050402 IP Transmission Introduction on Iub Interface must be
configured before this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others
The ATM/IP transmission link from the RNC to the NodeB is configured.
Context
This feature allows NodeB to support the ATM/IP dual-stack transmission. Services with
different QoS requirements can be carried on the links of different protocols. In addition, the
transmission backup is also provided.
Procedure
l Activation Procedure
NOTE
When you allocate resources for ATM/IP dual stack-based transport on the Iub interface, take the
following suggestions into consideration:
l ATM transport, IP transport, or ATM/IP hybrid transport is applicable to control plane data. It
is recommended that ATM/IP hybrid transport be applied to control plane data for security
purposes. That is, the SAAL and SCTP links together carry an NCP or a CCP, and the SAAL
link is the active link.
l ATM transport, IP transport, or ATM/IP hybrid transport is applicable to user plane data. It is
recommended that:
l ATM transport be applied to signaling, voice services, CS conversational services, CS
streaming services, PS conversational services, and PS streaming services.
l IP transport be applied to PS interactive services, PS background services, HSDPA
conversational services, HSDPA streaming services, HSDPA interactive services, HSDPA
background services, HSUPA conversational services, HSUPA streaming services, HSUPA
interactive services, and HSUPA background services.
l Either ATM or IP transport is applicable to management plane data. It is recommended that IP
transport be applied.
1. Run the BSC6900 MML command ADD UNODEB (CME single configuration:
Main View > Right Click RNC > Create Logical NodeB; CME batch modification
center: not supported) to add a NodeB. In this step, set IUB Trans Bearer Type to
ATMANDIP_TRANS.
2. Run the BSC6900 MML command ADD TRMMAP (CME single configuration:
UMTS Global Configuration Express > Transmission Resources Configuration
> Transport Resource Mapping; CME batch modification center: not supported).
In this step, set Interface Type to IUB and Transport Type to ATM_IP.
3. Run the BSC6900 MML command ADD ADJNODE (CME single configuration:
NodeB Configuration Express > IUB_RNC > ATM Transport > Adjacent
Node; CME batch modification center: not supported) to add an adjacent node. In this
step, set Adjacent Node Type to IUB and Transport Type to ATM_IP. If the node
is a leaf node, set Is Root Node to YES; otherwise, set Is Root Node to NO.
4. Run the BSC6900 MML command ADD AAL2PATH (CME single configuration:
NodeB Configuration Express > IUB_RNC > ATM Transport > AAL2 Path;
CME batch modification center: not supported) to add an AAL2 path.
5. Run the BSC6900 MML command ADD IPPATH (CME single configuration:
NodeB Configuration Express > IUB_RNC > IP Transport > IP Path; CME batch
modification center: not supported) to add an IP path. In this step, set Interface
Type to IUB and Transport Type to IP.
6. Run the BSC6900 MML command ADD ADJMAP (CME single configuration:
NodeB Configuration Express > IUB_RNC > ATM Transport > Adjacent Node
Mapping; CME batch modification center: not supported). In this step, set Interface
Type to IUB and Transport Type of the adjacent node and interface type to
ATM_IP.
l Verification Procedure
1. Use a UE to make a call and perform FTP downloading. High-priority services (such
as calls and web browsing) can be carried on ATM paths and low-priority services
(FTP downloading) can be carried on IP paths.
2. Run the BSC6900 MML command DSP IPPATH to check the state of the IP path
and whether any resources of the path are occupied.
Expected result: Operation state is Available, and some resources of the path are
occupied.
3. Run the BSC6900 MML command DSP AAL2PATH to check the state of the AAL2
path and whether any resources of the path are occupied.
Expected result: Operation state is Available, and some resources of the path are
occupied.
l Deactivation Procedure
1. Run the BSC6900 MML command RMV ADJMAP (CME single configuration:
NodeB Configuration Express > IUB_RNC > ATM Transport > Adjacent Node
Mapping; CME batch modification center: not supported) to remove the TRM
mapping to the adjacent node.
2. Run the BSC6900 MML command RMV TRMMAP (CME single configuration:
UMTS Global Configuration Express > Transmission Resources Configuration
> Transport Resource Mapping; CME batch modification center: not supported) to
remove the transmission resource mapping on the Iub interface.
3. Run the BSC6900 MML command RMV IPPATH (CME single configuration:
NodeB Configuration Express > IUB_RNC > IP Transport > IP Path; CME batch
modification center: not supported) to remove the IP path on the Iub interface.
----End
Example
//Configuring ATM/IP Dual Stack NodeB
//Adding a NodeB
ADD UNODEB: NodeBName="test", NodeBId=115, SRN=0, SN=0,
TnlBearerType=ATMANDIP_TRANS, IPTRANSAPARTIND=SUPPORT,
HostType=SINGLEHOST, SharingType=DEDICATED, CnOpIndex=0;
//Adding the transmission resource mapping
ADD TRMMAP: TMI=115, ITFT=IUB, TRANST=ATM_IP;
//Adding an adjacent node
ADD ADJNODE: ANI=115, NAME="test", NODET=IUB, NODEBID=115, TRANST=ATM_IP,
IsROOTNODE=YES, SAALLNKN=1;
//Adding an AAL2 path
ADD AAL2PATH: ANI=115, PATHID=115, CARRYT=UNI, CARRYF=1, CARRYSN=14,
CARRYUNILNKN=0, RSCGRPFLAG=NO, VPI=12, VCI=126, TXTRFX=115, RXTRFX=115,
AAL2PATHT=R99;
//Adding an IP path
ADD IPPATH: ANI=115, PATHID=115, ITFT=IUB, TRANST=IP, PATHT=QoS,
IPADDR="183.22.81.1", PEERIPADDR="22.22.22.23", TXBW=10000, RXBW=10000,
CARRYFLAG=NULL, VLANFlAG=DISABLE, PATHCHK=DISABLED;
//Adding the TRM mapping to the adjacent node
ADD ADJMAP: ANI=115, ITFT=IUB, TRANST=ATM_IP, CNMNGMODE=EXCLUSIVE,
CNOPINDEX=0, TMIGLD=115, TMISLV=115, TMIBRZ=115, FTI=0, LEIGLD=0,
LEISLV=0, LEIBRZ=0;
This section describes how to activate, verify, and deactivate the optional feature WRFD-050409
IP Transmission Introduction on Iu Interface.
Prerequisites
l Dependencies on Hardware
Only the Dopra Linux OS supports the built-in firewall function for O&M.
Only the FG2c and GOUc boards of the BSC6900 support the built-in firewall function
for interfaces.
Only the FG2a, GOUa, FG2c and GOUc boards of the BSC6900 support Bidirectional
Forwarding Detection (BFD).
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature provides a new lu transmission solution for operators. Compared with ATM
transmission, IP transmission can significantly reduce the transmission cost.
l The built-in firewall on the RNC side safeguards IP Ethernet ports on interface boards and
O&M ports against network attacks.
Procedure
Step 1 For configurations of Iu interface, see Initial Configuration Guide.
----End
This section describes how to activate, verify, and deactivate the optional feature WRFD-050410
IP Transmission Introduction on Iur Interface.
Prerequisites
l Dependencies on Hardware
Only the Dopra Linux OS supports the built-in firewall function for O&M.
Only the FG2c and GOUc boards of the BSC6900 support the built-in firewall function
for interfaces.
Only the FG2a, GOUa, FG2c and GOUc boards of the BSC6900 support Bidirectional
Forwarding Detection (BFD).
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others Prerequisites
The neighboring RNC supports IP transmission on the Iur interface.
Context
This feature provides a new lur transmission solution for operators. Compared with ATM
transmission, IP transmission can significantly reduce the transmission cost.
This feature enhances Iur transmission by introducing the following functions: BFD-based IP
fault detection and built-in firewall on the RNC side.
l If BFD-based IP fault detection is enabled, the BSC6900 triggers a port switchover, board
switchover, or IP rerouting when detecting that the gateway or the peer entity becomes
faulty. BFD can be classified into multi-hop BFD and single-hop BFD:
In multi-hop BFD, the IP addresses of the local and peer ports must be on different
network segments.
In single-hop BFD, the IP addresses of the local and peer ports must be on the same
network segment.
l The built-in firewall on the RNC side safeguards IP Ethernet ports on interface boards and
O&M ports against network attacks.
Procedure
Step 1 For configurations of Iur interface, see Initial Configuration Guide.
----End
This section describes how to activate, verify, and deactivate the optional feature WRFD-050420
Configuring FP MUX for IP Transmission.
Prerequisites
l Dependencies on Hardware
The FG2a/FG2c, GOUa/GOUc, and POUc support FP multiplexing for BSC6900.
l Dependencies on Other Features
The feature WRFD-050402 IP Transmission Introduction on Iub Interface has been
configured before this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others
The receive end of IP packets support FP mulptiplexing.
Context
The FP MUX feature encapsulates multiple packets with the same source IP address, destination
IP address, and DiffServ Code Point (DSCP) into one UDP/IP packet. This reduces the overhead
of packet headers and therefore improves the transmission efficiency.
FP MUX is a Huawei proprietary protocol. Both RNC and NodeB must support this feature.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command ADD IPMUX (CME single configuration: NodeB
Configuration Express > IUB_RNC > IP Transport > IP MUX Pipe; CME batch
modification center: not supported) to enable frame multiplexing on the Iub interface.
In this step, set IP MUX Type to FPMUX.
NOTE
You do not need to configure the number of packets for multiplexing, the BSC6900 selects
proper subframes for multiplexing based on the length of subframes. Subframes that meet the
following conditions are multiplexed into packets:
1. The total sending duration of subframes is smaller than Maximum Delay Time.
2. The length of the subframe is smaller than Max subframe length.
3. The total length of subframes plus eight is smaller than or equal to Maximum Frame
Length.
2. Run the NodeB MML command SET FPMUX (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Basic Information > Transport
Management > FP Multiplexing Switch; CME batch modification center: not
supported) to configure FP multiplexing on the Iub interface on the NodeB side.
l Verification Procedure
1. Run the BSC6900 MML command DSP IPMUX to check IP packet multiplexing
conditions.
2. Run the NodeB MML command LST FPMUX to query the FP multiplexing condition
of an IP path.
l Deactivation Procedure
1. Run the BSC6900 MML command RMV IPMUX (CME single configuration:
NodeB Configuration Express > IUB_RNC > IP Transport > IP MUX Pipe; CME
batch modification center: not supported) to disable the FP multiplexing function for
the IP path.
2. Run the NodeB MML command SET FPMUX (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Basic Information > Transport
Management > FP Multiplexing Switch; CME batch modification center: not
supported) to disable FP multiplexing on the NodeB side.
----End
Example
//Acitvating FP MUX for IP Transmission on the RNC side
ADD IPMUX: MUXTYPE=FPMUX, ANI=1, PATHID=1, ISQOSPATH=NO, SUBFRAMELEN=352,
MAXFRAMELEN=1031;
//Acitvating FP MUX for IP Transmission on the NodeB side
SET FPMUX: FPMUXSWITCH =ENABLE;
//Verifying FP MUX for IP Transmission on the RNC side
DSP IPMUX: IPMUXINDEX=1;
//Verifying FP MUX for IP Transmission on the NodeB side
LST FPMUX:;
//Deacitvating FP MUX for IP Transmission on the RNC side
RMV IPMUX: IPMUXINDEX=1;
//Deacitvating FP MUX for IP Transmission on the NodeB side
SET FPMUX: FPMUXSWITCH =DISABLE;
This section describes how to activate, verify, and deactivate the optional feature WRFD-050422
Dynamic Bandwidth Control of Iub IP.
Prerequisites
l Dependencies on Hardware
The FG2a, FG2c, GOUa and GOUc support this feature for BSC6900.
l Dependencies on Other Features
The configurations of the features on which this feature depends are complete. This
feature depends on the feature WRFD-050402 IP Transmission Introduction on Iub
Interface.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature enables the RNC to adjust the transmission bandwidth according to the packet loss
ratio and jitter over links detected by the IP performance monitor (PM).
Procedure
l Activating Procedure
1. Run the BSC6900 MML command ADD IPLOGICPORT (CME single
configuration: NodeB Configuration Express > IUB_RNC > IP Transport > IP
Logical Port; CME batch modification center: not supported). In this step, set Auto
adjust bandwidth switch to ON, Max bandwidth and Min bandwidth to
appropriate values.
2. Run the BSC6900 MML command ADD IPPATH (CME single configuration:
NodeB Configuration Express > IUB_RNC > IP Transport > IP Path; CME batch
modification center: not supported) to add a new IP PATH over the new logic port.
3. Run the BSC6900 MML command ACT IPPM (CME single configuration: NodeB
Configuration Express > IUB_RNC > IP Transport > IPPM; CME batch
modification center: not supported) to activate the IP PM of the new IP PATH.
l Verification Procedure
1. Log on the BSC6900 LMT. On the displayed monitoring navigation tree, choose
Monitor > Common Monitoring > Link Performance Monitoring to create a task
of logical port bandwidth monitoring.
NOTE
l Configure monitoring parameters, select Logical Port Bandwidth for Monitor Item, and set the
Subrack No. and Slot No. of the logical port.
l Expected result: when the rate of packet discard and delay exceed the threshold (which can be
set by running the BSC6900 MML command ADD IPLOGICPORT), you can obtain that the
logic port bandwidth changes within the range defined by Max bandwidth and Min
bandwidth.
l Deactivating Procedure
1. Run the BSC6900 MML command MOD IPLOGICPORT (CME single
configuration: NodeB Configuration Express > IUB_RNC > IP Transport > IP
Logical Port; CME batch modification center: not supported). In this step, set Auto
adjust bandwidth switch to OFF.
2. Run the BSC6900 MML command DEA IPPM (CME single configuration: NodeB
Configuration Express > IUB_RNC > IP Transport > IPPM; CME batch
modification center: not supported) to deactivate the IP PM.
----End
Example
ADD IPLOGICPORT: SRN=0, SN=14, BT=FG2a, LPN=0, CARRYT=ETHER, PN=0,
RSCMNGMODE=SHARE, BWADJ=ON, MAXBW=100, MINBW=50, FLOWCTRLSWITCH=ON,
OPSEPFLAG=OFF;
ADD IPPATH: ANI=0, PATHID=1, ITFT=IUB, TRANST=IP, PATHT=BE,
IPADDR="80.1.1.1", PEERIPADDR="10.161.0.1", TXBW=100, RXBW=1000,
CARRYFLAG=IPLGCPORT, LPNSN=14, LPN=0, VLANFlAG=DISABLE, PATHCHK=DISABLED;
ACT IPPM: ANI=0, PATHID=1, ISQOSPATH=NO, LOSTPKTDETECTSW=OFF;
//Deactivating dynamic bandwidth control of Iub IP
MOD IPLOGICPORT: SRN=0, SN=14, BT=FG2a, LPN=0, BWADJ=OFF, CIR=100;
DEA IPPM: ANI=0, PATHID=1;
This section describes how to activate, verify, and deactivate the optional feature WRFD-050408
Overbooking on IP Transmission.
Prerequisites
l Dependencies on Hardware
BSC6900 IP interface boards (PEUa/FG2a/FG2c/GOUa/GOUc board) all support
backpressure mechanism
FG2a/FG2c/GOUa/GOUc/ in BSC6900 support LP shaping.
l Dependencies on Other Features
The feature WRFD-050402 IP Transmission Introduction on Iub Interface must be
configured before this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
The transmission rate of UMTS services varies during the transmission. For example, the rate
of a speech service is 12.2 kbit/s when someone is speaking and is low when no one is speaking.
Overbooking on IP Transmission helps save transmission resources on the Iub interface,
reducing the CAPEX and OPEX of the operator on transmission resources.
Procedure
l Activation Procedure
Take the FE/GE-based IP transmission on the Iub interface as an example to describe how
to verify backpressure-based downlink flow control.
1. On the BSC6900 LMT, start downlink traffic and bandwidth tracing tasks on the Uu,
Iub, and Iu interfaces.
2. Register an R99 user UE1 in the HLR. Enable UE1 with streaming services and with
both highest uplink rate and highest downlink rate of 384 Kbit/s.
3. Register an HSDPA user UE2 in the HLR. Enable UE2 with background services and
with highest uplink rate of 384 Kbit/s and highest downlink rate of 1450 Kbit/s.
4. Run the BSC6900 MML command ADD TRMMAP to map R99 services to high-
priority queue and HSDPA services to low-priority queue.
5. All IP paths of the RNC are carried on a logical port. Enable the port flow control
when adding the logical port.
6. Enable UE1 and UE2 to stay in idle mode and camp on the test cell. The test cell must
support HSDPA services.
7. Use UE1 to perform PS streaming services, that is, use UE1 to download files from
the FTP server.
Expected result: The logical port is not congested and UE1 downloads data at the
highest rate.
8. Use UE2 to perform PS BE services, that is, use UE2 to download files from the FTP
server.
Expected result: The logical port is congested and the backpressure function is
triggered. The downloading rate of UE2 decreases and that of UE1 remains
unchanged. This is because R99 services have a higher priority.
l Deactivation Procedure
Deactivating RLC retransmission rate-based downlink congestion control
Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express > Connection_Oriented
RRM Switch Configuration > Connection Oriented Algorithm Switches; CME
batch modification center: 3.15 Modifying RNC Parameters in Batches) to switch off
flow control.
For R99 BE services, deselect DRA_R99_DL_FLOW_CONTROL_SWITCH in
Dynamic Resource Allocation Switch.
For HSDPA BE services, deselect
DRA_HSDPA_DL_FLOW_CONTROL_SWITCH in Dynamic Resource
Allocation Switch.
Deactivating backpressure-based downlink congestion control
1. Run the BSC6900 MML command MOD PPPLNK (CME single configuration:
NodeB Configuration Express > IUB_RNC > IP Transport > PPP Link; CME
batch modification center: not supported). In this step, set Flow control switch to
OFF.
2. Run the BSC6900 MML command MOD MPGRP (CME single configuration:
NodeB Configuration Express > IUB_RNC > IP Transport > MP Group; CME
batch modification center: not supported). In this step, set Flow control switch to
OFF.
3. Run the BSC6900 MML command MOD IPLOGICPORT (CME single
configuration: NodeB Configuration Express > IUB_RNC > IP Transport >
IP Logical Port; CME batch modification center: not supported). In this step, set
Flow control switch to OFF.
Deactivating IP shaping
1. Run the BSC6900 MML command MOD IPPATH (CME single configuration:
NodeB Configuration Express > IUB_RNC > IP Transport > IP Path; CME
batch modification center: not supported) to modify a logical port. In this step, set
Bearing type to NULL(NULL).
Example
//Activating RLC retransmission rate-based downlink congestion control
SET UCORRMALGOSWITCH:
DraSwitch=DRA_HSDPA_DL_FLOW_CONTROL_SWITCH-1&DRA_R99_DL_FLOW_CONTROL_SWIT
CH-1;
//Activating IP shaping
ADD IPLOGICPORT: SRN=0, SN=27, BT=FG2a, LPNTYPE=Leaf, LPN=0,
CARRYT=ETHER, PN=0, RSCMNGMODE=SHARE, BWADJ=OFF, CIR=1000,
FLOWCTRLSWITCH=ON;
ADD IPPATH: ANI=0, PATHID=1, ITFT=IUB, TRANST=IP, PATHT=BE,
IPADDR="80.1.1.1", PEERIPADDR="10.161.0.1", PEERMASK="255.255.255.0",
TXBW=1000, RXBW=1000, CARRYFLAG=IPLGCPORT, LPNSN=0, LPN=0,
VLANFlAG=DISABLE, PATHCHK=DISABLED;
//Deactivating IP shaping
MOD IPPATH: ANI=0, PATHID=1, ITFT=IUB, CARRYFLAG=NULL;
MOD IPLOGICPORT: SRN=0, SN=27, BT=FG2a, LPN=0, FLOWCTRLSWITCH=OFF;
This section describes how to activate, verify, and deactivate the optional feature WRFD-050107
IP Routing-Based Hub NodeB.
Prerequisites
l Dependencies on Hardware
Only 3900 series base stations support this feature.
BTS3902E doesn't support this feature.
l Dependencies on Other Features
The feature WRFD-050402 IP Transmission Introduction on Iub Interface must be
configured before this feature is activated.
l License
This feature is not under license control.
Context
This feature enables Huawei NodeBs to provide the transmission convergence function in IP
mode, therefore increasing transmission efficiency and reducing transmission costs.
Procedure
l Activation Procedure
1. On NodeBs locating on all leaf nodes and root nodes, run the NodeB MML
command ADD IPRT (CME single configuration: NodeB Configuration Express
> IUB_NodeB > IP Transport Layer > IPRoute > IP Route; CME batch
modification center: not supported) to add an IP route from the NodeB to the
BSC6900 or M2000.
l Verification Procedure
1. Run the NodeB MML command DSP IPRT to query the configuration of the newly
added IP route.
l Deactivation Procedure
1. Run the NodeB MML command RMV IPRT (CME single configuration: NodeB
Configuration Express > IUB_NodeB > IP Transport Layer > IPRoute > IP
Route; CME batch modification center: not supported) to remove the IP route.
----End
Example
l NodeB V200R014
//Activation procedure
ADD IPRT: SRN=0, SN=7, SBT=BASE_BOARD, DSTIP="11.11.11.11",
DSTMASK="255.255.255.0", RTTYPE=NEXTHOP, NEXTHOP="10.10.10.10";
//Verification procedure
DSP IPRT: CN=0, SRN=0, SN=7;
//Deactivation procedure
RMV IPRT: SRN=0, SN=7, SBT=BASE_BOARD, DSTIP="11.11.11.11",
DSTMASK="255.255.255.0", RTTYPE=NEXTHOP, NEXTHOP="10.10.10.10";
l NodeB V100R014
//Activation procedure
ADD IPRT: SRN=0, SN=12, SBT=BASE_BOARD, DSTIP="11.11.11.11",
DSTMASK="255.255.255.0", RTTYPE=NEXTHOP, NEXTHOP="10.10.10.10";
//Verification procedure
DSP IPRT:;
//Deactivation procedure
RMV IPRT: SRN=0, SN=12, SBT=BASE_BOARD, DSTIP="11.11.11.11",
DSTMASK="255.255.255.0", RTTYPE=NEXTHOP, NEXTHOP="10.10.10.10";
This section describes how to activate, verify, and deactivate the optional feature WRFD-011500
PDCP Header Compression (RFC2507).
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others
The UE should support the compression function.
Context
This feature complies with the header compression function of data packet as defined in RFC
2507. It enables the deletion of redundant information such as TCP/IP header. The system
compresses the redundant protocol header before the data is transmitted on a link. In addition,
the system can decompress the received data. This feature can decrease the throughput on the
Uu interface and improve the efficiency of radio links.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to select the CFG_PDCP_RFC2507_HC_SWITCH check
box under the Channel configuration strategy switch parameter.
l Verification Procedure
1. Initiate UE tracing on the BSC6900 LMT.
2. Establish a PS service on the UE. Observe the CRLC _SETUP_REQ message in the
traced UE data. Check the bit1RfcInfo2507 IE in the following path in the message:
pdcpSetupInfo> pdcpInfo> pdcpInfoBmp> bit1RfcInfo2507.
If the value of the bit1RfcInfo2507 IE is 1, you can infer that this feature has been
activated.
If the value of the bit1RfcInfo2507 IE is 0, you can infer that this feature has not
been activated.
l Deactivation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to clear the CFG_PDCP_RFC2507_HC_SWITCH check
box under the Channel configuration strategy switch parameter.
----End
Example
//Activating PDCP Header Compression (RFC2507).
SET UCORRMALGOSWITCH: CfgSwitch=CFG_PDCP_RFC2507_HC_SWITCH-1;
//Deactivating PDCP Header Compression (RFC2507).
SET UCORRMALGOSWITCH: CfgSwitch=CFG_PDCP_RFC2507_HC_SWITCH-0;
This section describes how to activate, verify, and deactivate the optional feature WRFD-012001
RNC Offload. With this feature, the RNC can send some PS service data directly to Internet
over the offload Gi interface.
Prerequisites
l Dependencies on Hardware
The Gi interface between the RNC and the Internet is supported only by the FG2c board
and the GOUc board.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
l Others
The RNC supports the Network Address Translation (NAT) technology.
Context
The RNC Offload function is applied by means of NAT. The RNC analyzes the uplink data flow,
performs NAT on some service data, and then sends the service data to the Internet over the
offload Gi interface. Figure 216-1 shows the offload Gi interface between the RNC and the
Internet.
To enable data packets from the Internet to directly arrive at the RNC (instead of the GGSN),
the source IP address of an uplink data packet must be changed to the public IP address of the
offload Gi interface by means of NAT. In this way, the downlink data packets can flow into the
UTRAN over the offload Gi interface.
The RNC Offload function can be configured on the basis of IMEI, IMSI, cell, service type,
Access Point Name (APN), and destination IP address.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command ADD BRD (CME single configuration: Device
Panel > Add Board; CME batch modification center: not supported) to add an FG2c
board.
2. Run the BSC6900 MML command SET ETHPORT (CME single configuration:
Device Panel > Right click Board > Properties > Ethernet Port Parameters; CME
batch modification center: not supported) to set the Ethernet port attributes of the FG2c
board.
3. Run the BSC6900 MML command ADD ETHREDPORT (CME single
configuration: Device Panel > Right click Board > Properties > Ethernet Red
Port; CME batch modification center: not supported) to add two Ethernet ports as
active and standby ports.
4. Run the BSC6900 MML command ADD UGIPORT (CME single configuration: Gi
Configuration Express > IP Transport > Gi port; CME batch modification center:
not supported) to add a Gi interface.
5. Run the BSC6900 MML command ADD ETHIP (CME single configuration: Gi
Configuration Express > IP Transport > Ethernet Port IP Address; CME batch
modification center: not supported) to add an IP address of the Gi interface.
6. Run the BSC6900 MML command ADD IPRT (CME single configuration: Gi
Configuration Express > IP Transport > IP Route; CME batch modification center:
not supported) to add a route from the Gi interface to the firewall.
7. Run the BSC6900 MML command ADD UNATRESPOOL (CME single
configuration: Gi Configuration Express > IP Transport > NAT resource pool;
CME batch modification center: not supported) to add a NAT resource pool.
8. Run the BSC6900 MML command SET UNATSWITCH (CME single
configuration: Gi Configuration Express > IP Transport > NAT function switch;
CME batch modification center: not supported) to enable the NAT function.
9. Run the BSC6900 MML command SET UNATALG (CME single configuration: Gi
Configuration Express > IP Transport > NAT function parameters; CME batch
modification center: not supported) to set the Application Level Gateway (ALG)
function for the protocols over the Gi interface.
10. Run the BSC6900 MML command ADD UOFFLOAD (CME single configuration:
UMTS Radio Global Configuration Express > Local Break Out Configuration >
Global SIPTO Parameters; CME batch modification center: not supported) to
configure RNC Offload for the operator.
11. Run the BSC6900 MML command ADD UOFFLOADRAB (CME single
configuration: UMTS Radio Global Configuration Express > Local Break Out
Configuration > SIPTO RAB Restriction; CME batch modification center: not
supported) to configure RNC Offload based on user priority and service type.
12. (Optional) To configure RNC Offload based on IMEI, run the BSC6900 MML
command MOD UOFFLOAD (CME single configuration: UMTS Radio Global
Configuration Express > Local Break Out Configuration > Global SIPTO
Parameters; CME batch modification center: not supported) to enable the TAC-level
offload function. Then, run the BSC6900 MML command ADD
UOFFLOADIMEITAC (CME single configuration: UMTS Radio Global
Configuration Express > Local Break Out Configuration > TAC to Be Enabled
with Offload; CME batch modification center: not supported) to configure the TAC-
level offload function. For details about Type Allocation Code (TAC), see the MML
command ADD UIMEITAC (CME single configuration: UMTS Global
Configuration Express > RNC Basic Configuration > IMEI TAC; CME batch
modification center: not supported).
13. (Optional) To configure RNC Offload based on APN, run the BSC6900 MML
command ADD UOFFLOADAPN (CME single configuration: UMTS Radio
Global Configuration Express > Local Break Out Configuration > APN; CME
batch modification center: not supported) to add a registered APN for the operator.
Then, run the BSC6900 MML command MOD UOFFLOAD (CME single
configuration: UMTS Radio Global Configuration Express > Local Break Out
Configuration > Global SIPTO Parameters; CME batch modification center: not
supported) to enable RNC Offload based on APN.
14. (Optional) To configure RNC Offload based on IMSI, run the BSC6900 MML
command ADD UOFFLOADIMSI (CME single configuration: UMTS Radio
Global Configuration Express > Local Break Out Configuration > SIPTO IMSI
Range; CME batch modification center: not supported) to set the range of IMSIs
supporting RNC Offload.
15. (Optional) To configure RNC Offload based on the cell, run the BSC6900 MML
command MOD UCELLALGOSWITCH (CME single configuration: UMTS Cell
Configuration Express > Cell Parameters > Cell Algorithm Switches; CME batch
modification center: 3.18 Modifying UMTS Cell Parameters in Batches) to enable
RNC Offload for the cell.
16. (Optional) To configure RNC Offload based on the destination IP address, run the
BSC6900 MML command ADD UUNOFFLOADIP (CME single configuration:
UMTS Radio Global Configuration Express > Local Break Out Configuration >
Host IP Address/Host Network Segment That not Allow Visit in Offload Mode;
CME batch modification center: not supported) to set the IP addresses or network
segment that are not allowed to access the Internet using RNC Offload.
l Verification Procedure
1. On the BSC6900 LMT, choose Monitor > UMTS monitoring, and then double-click
Cell Performance Monitoring. The Cell Performance Monitoring dialog box is
displayed.
2. Set Monitor Item to Cell User Number, and then set Monitor Period and Cell ID.
Click OK.
3. Choose Monitor > Common Monitoring. Double-click Link Performance
Monitoring. The Link Performance Monitoring dialog box is displayed.
4. Set Monitor Item to FE/GE, Subrack No. to 0, Slot No. to 14, Monitor Type to
Port, and FE/GE Port No. to 0. Click OK.
5. Power on a UE and enable the UE to camp on CELL1. Use the UE to initiate a PS
service.
6. Check the Cell User Number parameter. The number of UEs supporting RNC Offload
in the cell changes from 0 to 1.
7. The UE starts data transmission.
8. Check the FE/GE parameter. The data throughput over the FE/GE port increases.
l Deactivation Procedure
1. Run the BSC6900 MML command MOD UOFFLOAD (CME single configuration:
UMTS Radio Global Configuration Express > Local Break Out Configuration >
Global SIPTO Parameters; CME batch modification center: not supported) to
disable RNC Offload for the operator.
----End
Example
//Configuring the Gi interface
ADD BRD: SRN=0, BRDCLASS=INT, BRDTYPE=FG2c, SN=14, RED=YES, MPUSUBRACK=0,
MPUSLOT=0;
SET ETHPORT: SRN=0, SN=14, BRDTYPE=FG2c, PTYPE=GE, PN=0, SPEED=AUTO;
ADD ETHREDPORT: SRN=0, SN=14, PN=0;
ADD UGIPORT: SRN=0, SN=14, PN=0, ISPSSHAREPORT=NO;
ADD ETHIP: SRN=0, SN=14, PN=0, IPINDEX=0, IPADDR="10.53.50.69",
MASK="255.255.255.240";
ADD IPRT: SRN=0, SN=14, DSTIP="0.0.0.0", DSTMASK="0.0.0.0",
NEXTHOP="10.53.50.68", PRIORITY=HIGH, REMARK="Gi";
//Configuring the NAT function
ADD UNATRESPOOL: SRN=0, SN=14, PN=0, NATINDEX=0,
STARTADDR="172.168.0.100", ENDADDR="172.168.0.101", MAXPN=65535,
MINPN=10000;
SET UNATSWITCH: NATSW=ON;
SET UNATALG: PROTOCOLTYPE=FTP, ALGSW=ON, AGINGTIMER=600;
//Activating RNC Offload
ADD UOFFLOAD: CnOpIndex=0, OffloadSwitch=ON, NonDTRAB=PERMIT_OFFLOAD;
ADD UOFFLOADRAB: CnOpIndex=0, UserPriority=GOLDEN_USER,
OffloadService=STREAMING-1&INTERACTIVE-1&BACKGROUND-0;
//Configuring RNC Offload based on IMEI
MOD UOFFLOAD: CnOpIndex=0, RsvdPara1=LBO_IMEITAC_SWITCH-1;
ADD UOFFLOADIMEITAC: TAC=12345678, Description="iphone";
//Configuring RNC Offload based on APN
MOD UOFFLOAD: CnOpIndex=0, OffloadSwitch=ON, NonDTRAB=NOT_PERMIT_OFFLOAD,
RegAPN=PERMIT_OFFLOAD;
//Configuring RNC Offload based on IMSI
ADD UOFFLOADIMSI: CnOpIndex=0, IMSIStart="000000000000000",
IMSIEnd="999999999999999";
//Configuring RNC Offload based on the cell
MOD UCELLALGOSWITCH: CellId=111, OffloadSwitch=ON;
//Configuring RNC Offload based on destination IP address
ADD UUNOFFLOADIP: CnOpIndex=0, IpAddr="10.10.10.10",
Mask="255.255.255.255";
//Deactivating RNC Offload
MOD UOFFLOAD: CnOpIndex=0, OffloadSwitch=OFF;
This section describes how to activate, verify, and deactivate the feature WRFD-050412 UDP
MUX for Iu-CS Transmission.
Prerequisites
l Dependencies on Hardware
This feature is supported only by the BSC6900 that is configured with the FG2a/GOUa/
FG2c/GOUc/POUc boards.
l Dependencies on Other Features
The feature WRFD-050409 IP Transmission Introduction on Iu Interface has been
configured before this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The CS CN element (MGW) supports UDP MUX.
The RTCP switch has been opened. Run the BSC6900 MML command ADD
UCNNODE (CME single configuration: UMTS Global Configuration Express >
Core Network > UMTS CN Node; CME batch modification center: not supported) to
set the RTCP SWITCH to ON.
Context
After IP transmission is introduced to the Iu-CS interface, UP packets, especially short packets
like CS packets, cannot be transmitted efficiently after being encapsulated at the RTP, UDP, and
IP layers.
This feature helps solve this problem by using a UDP subheader shorter than UDP to encapsulate
multiple RTP packets into a UDP. This reduces resources used by packet headers and therefore
improves the efficiency of Iu-CS transmission.
This feature supports UDP MUX, regardless of whether compression of RTP headers is enabled.
After this feature is enabled, transmission efficiency can be increased by 30% to 40%, depending
on the number of RTP packets that are encapsulated into a UDP.
Procedure
l Activation Procedure
NOTE
Configure IP paths based on the network plan.
1. Run the BSC6900 MML command ADD IPMUX (CME single configuration: IUCS
Configuration Express > IP Transport > IP MUX Pipe; CME batch modification
center: not supported) or MOD IPMUX (CME single configuration: IUCS
Configuration Express > IP Transport > IP MUX Pipe; CME batch modification
center: not supported) to enable the Iu-CS UDP MUX function. In this step, set IP
MUX Type to UDPMUX, and set Max subframe length[byte], Maximum Frame
Length[byte], and Maximum Delay Time[ms] to appropriate values based on the
network plan. To enable the UDP MUX function for multiple links, run this command
for each of the links.
l Verification Procedure
1. Run the BSC6900 MML command DSP IPMUX to query the application of UDP
MUX for Iu Transmission. Check whether the feature has been activated based on the
values of IPMUX Status, Number of MUX packets, and Number of MUX Sub-
frames.
l Deactivation Procedure
1. Run the BSC6900 MML command RMV IPMUX (CME single configuration: IUCS
Configuration Express > IP Transport > IP MUX Pipe; CME batch modification
center: not supported) to remove the IP MUX paths or run the BSC6900 MML
command MOD IPMUX (CME single configuration: IUCS Configuration
Express > IP Transport > IP MUX Pipe; CME batch modification center: not
supported) to set IP MUX Type to FPMUX.
----End
Example
//Activating UDP MUX for Iu-CS Transmission
ADD IPMUX: MUXTYPE=UDPMUX, SUBFRAMELEN=352, MAXFRAMELEN=1031, FPTIMER=2;
//Checking whether UDP MUX for Iu-CS Transmission has been activated for
an IP MUX path of which the index is 1
DSP IPMUX: IPMUXINDEX=1;
This section describes how to activate, verify, and deactivate the optional feature WRFD-140207
Iu/Iur Transmission Resource Pool in RNC.
Prerequisites
l Dependencies on Hardware
The GOUc and FG2c boards support this feature.
l Dependencies on Other Features
Configurations of other features on which this feature depends are complete.This feature
depends on features WRFD-050409 IP Transmission Introduction on Iu Interface or
WRFD-050410 IP Transmission Introduction on Iur Interface.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The RNC can communicate with an interconnected NE by any route using their
respective user-plane IP addresses.
Deploying this feature on RNC transmission ports that work in active/standby mode
requires Huawei professional services.
Context
With this feature, multiple Iu or Iur interface boards form a transmission resource pool. A
network element (NE) interconnected with the RNC, such as a neighboring RNC (NRNC), the
MGW, the SGSN, or the GGSN, can access all boards in this pool. This helps balance the load
among these boards.
l Data Preparation
See Data Preparation for Initial Configuration in the Initial Configuration Guide.
Procedure
l Activation Procedure
Initial configuration scenarios
Iu-CS interface
1. See Configuring the Physical Layer and Data Link Layer for the FG2c/GOUc
Board in the Initial Configuration Guide.
2. See Configuring the Transmission Resource Pool in the Initial Configuration
Guide.
3. See Configuring the Control Plane of the Iu-CS Interface (over Transmission
Resource Pool) in the Initial Configuration Guide.
4. See Configuring the User Plane of the Iu-CS Interface (over Transmission
Resource Pool) in the Initial Configuration Guide.
5. See Configuring the Mapping Between Service Types and Transmission
Resources for the Adjacent Node in the Initial Configuration Guide.
Iu-PS interface
1. See Configuring the Physical Layer and Data Link Layer for the FG2c/GOUc
Board in the Initial Configuration Guide.
2. See Configuring the Transmission Resource Pool in the Initial Configuration
Guide.
3. See Configuring the Control Plane of the Iu-PS Interface (over Transmission
Resource Pool) in the Initial Configuration Guide.
4. See Configuring the User Plane of the Iu-PS Interface (over Transmission
Resource Pool) in the Initial Configuration Guide.
5. See Configuring the Mapping Between Service Types and Transmission
Resources for the Adjacent Node in the Initial Configuration Guide.
Iur interface
1. See Configuring the Physical Layer and Data Link Layer for the FG2c/GOUc
Board in the Initial Configuration Guide.
2. See Configuring the Transmission Resource Pool in the Initial Configuration
Guide.
3. See Configuring the Control Plane of the Iur Interface (over Transmission
Resource Pool) in the Initial Configuration Guide.
4. See Configuring the User Plane of the Iur Interface (over Transmission
Resource Pool) in the Initial Configuration Guide.
5. See Configuring the Mapping Between Service Types and Transmission
Resources for the Adjacent Node in the Initial Configuration Guide.
NOTE
For details about the initial configuration on the CME, see Initial Configuration of the BSC6900
(V900R014) > BSC6900 UMTS Initial Configuration (V900R014) > Configuring the BSC6900 in
the General Configuration Procedure > Configuring Iu-CS Interface Data (in Transmission Resource
Pool Mode)/Configuring Iu-PS Interface Data (in Transmission Resource Pool Mode)/Configuring
Iur Interface Data (in Transmission Resource Pool Mode) in the documentation CD-ROM of (For
Customer) M2000-CME Product Documentation (V200R012)(HDX)-EN.
Reconfiguration scenarios
Iu-CS interface
See Configuring the IP Pool Networking Mode on the Iu-CS Interface in the
Reconfiguration Guide.
Iu-PS interface
See Configuring the IP Pool Networking Mode on the Iu-PS Interface in the
Reconfiguration Guide.
Iur interface
See Configuring the IP Pool Networking Mode on the Iur Interface in the
Reconfiguration Guide.
l Verification Procedure
1. Run the BSC6900 MML commandDSP ETHPORT to query the port rate and work
mode.
Expected result: Speed is 1000M and Duplex is FULL.
2. Run the BSC6900 MML commandDSP SRCIPRT to check whether the transmitted
and received data over the source IP address uses an interface board in the same slot.
If the values of Number of Packets Sent and Number of Packets Received
increase in the same slot, it indicates that the route priority on the RNC side is
consistent with that on the peer router side.
If the value of Number of Packets Received increases in the active and standby
slots, it indicates that an equal-cost route has been configured from the router to
the RNC. In this case, change the route to active and standby routes.
If the slot where the value of Number of Packets Received increases is different
from the slot where the value of Number of Packets Sent increases, it indicates
that the route priority on the RNC side is inconsistent with that on the peer router
side. In this case, change the route priority.
3. Run the ping command and check for relevant alarms. Verify that the alarms
ALM-21392 Adjacent Node IP Address Ping Failure, ALM-21393 Adjacent Node IP
Path Ping Failure are not reported and ALM-21394 Transmission Resource Pool Ping
Packet Loss.
4. Run the BSC6900 MML commandDSP IPPOOL. In this step, check the values of
Send bit rate of the port[bps], Receive bit rate of the port[bps], Send bit rate load
of the board, Receive bit rate load of the board, Send packets load of the board,
and Receive packets load of the board for all egress ports corresponding to the source
IP addresses in transmission resource pools. Verify that these values of the egress
ports are close to each other.
l Deactivation Procedure
This feature does not need to be deactivated.
----End
Example
//Activation Procedure
//Refer to the example of a typical configuration script in the Initial
Configuration Guide.
//Deactivation Procedure
//Not involved.
This section describes how to activate, verify, and deactivate the optional feature WRFD-140208
Iub Transmission Resource Pool in RNC.
Prerequisites
l Dependencies on Hardware
The GOUc and FG2c boards support this feature.
For NodeBs, only the 3900 series base stations support this feature.
l Dependencies on Other Features
Configurations of other features on which this feature depends are complete. This
feature depends on feature WRFD-050402 IP Transmission Introduction on Iub
Interface.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others
The RNC can communicate with an interconnected NE by any route using their
respective user-plane IP addresses.
The requirements for the routers on the RNC side are as follows:
If the RNC boards work in active/standby mode, dynamic routing protocols such as
Open Shortest Path First (OSPF) and Intermediate System-to-Intermediate System
(ISIS) must be configured on the RNC, and policy-based routing must be configured
on routers.
Bidirectional Forwarding Detection (BFD) is configured for static routes on routers,
configuring fast reroute (FRR) is recommended to implement second-level fast
reroute.
Deploying this feature on RNC transmission ports that work in active/standby mode
requires Huawei professional services.
Context
With this feature, multiple Iub interface boards form a transmission resource pool. Each NodeB
interconnected with the RNC can access all boards in this pool. This helps balance the load
among these boards.
l Data Preparation
Data preparation on the RNC side
See Data Preparation for Initial Configuration in the Initial Configuration Guide.
Data preparation on the NodeB side
Parameter Name Parameter ID Setting Source
Description
Procedure
l Activation Procedure
Initial configuration scenarios
Configuration on the RNC side
1. See Configuring the Physical Layer and Data Link Layer for the FG2c/GOUc
Board in the Initial Configuration Guide.
2. See Configuring the Transmission Resource Pool in the Initial Configuration
Guide.
3. See Configuring the Control Plane of the Iub Interface (over Transmission
Resource Pool) in the Initial Configuration Guide.
4. See Configuring the User Plane of the Iub Interface (over Transmission
Resource Pool) in the Initial Configuration Guide.
5. See Configuring the Mapping Between Service Types and Transmission
Resources in the Initial Configuration Guide.
6. See Configuring the OM Channel over the Iub Interface (over Transmission
Resource Pool) in the Initial Configuration Guide.
NOTE
For details about the initial configuration on the CME, see Initial Configuration of the BSC6900
(V900R014) > BSC6900 UMTS Initial Configuration (V900R014) > Configuring the BSC6900
in the General Configuration Procedure > Configuring Iub Interface Data (in Transmission
Resource Pool Mode) in the documentation CD-ROM of (For Customer) M2000-CME Product
Documentation (V200R012)(HDX)-EN.
Configuration on the NodeB side
1. Run the NodeB MML commandADD DEVIP (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer >
IPPort > Device IP Address; CME batch modification center: 3.17 Modifying
Physical NodeB Parameters in Batches) to add a device IP address.
2. Run the NodeB MML commandADD SERVIP (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer > Basic
Configuration > ServerIP > Service IP; CME batch modification center: not
Example
//Activation Procedure
//Refer to the example of a typical configuration script in the Initial
Configuration Guide.
//Deactivation Procedure
//Not involved.
This section describes how to activate, verify, and deactivate the optional feature WRFD-050104
Satellite Transmission on Iub Interface.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature supports satellite transmission on the Iub interface, which is useful to cover remote
areas, such as an island.
When satellite transmission is applied over the Iub interface, the delay increases. The default
setting of the SAAL/SCTP timer on the Iub interface can meet the satellite transmission
requirements.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command MOD UNODEB (CME single configuration:
NodeB Configuration Express > IUB_RNC > NodeB Basic Information >
NodeB; CME batch modification center: not supported). In this step, set Satellite
Trans Ind to TRUE, and set IUB Transport Delay to 600.
2. Run the BSC6900 MML command ACT UCELL (CME single configuration: UMTS
Cell Configuration Express > Cell Basic Information > Cell Basic Information.
Set Validation indication to Activated; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches) to activate a cell.
l Verification Procedure
1. Run the BSC6900 MML command DSP UCELL to check whether cell settings are
successful.
2. Establish an AMR service in the cell. The AMR service is established successfully
and the speech quality is satisfactory.
3. Establish a PS BE service in a cell. The service is established successfully and the
data download rate is steady.
l Deactivation Procedure
1. Run the BSC6900 MML command DEA UCELL (CME single configuration: UMTS
Cell Configuration Express > Cell Basic Information > Cell Basic Information.
Set Validation indication to Deactivated; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches) to deactivate the cell.
2. Run the BSC6900 MML command MOD UNODEB (CME single configuration:
NodeB Configuration Express > IUB_RNC > NodeB Basic Information >
NodeB; CME batch modification center: not supported). In this step, set Satellite
Trans Ind to FALSE, and set IUB Transport Delay to 10.
----End
Example
//Activating Satellite Transmission on Iub Interface
MOD UNODEB: IDTYPE=BYID, NodeBId=1, TRANSDELAY=600, SATELLITEIND=TRUE;
ACT UCELL: CellId=1;
//Deactivating Satellite Transmission on Iub Interface
DEA UCELL: CellId=1;
MOD UNODEB: IDTYPE=BYID, NodeBId=1, TRANSDELAY=10, SATELLITEIND=FALSE;
This section describes how to activate, verify, and deactivate the optional feature WRFD-050108
Satellite Transmission on Iu Interface.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature solves the communication problems of base stations in remote areas, such as remote
regions, islands, and deserts, where there is no transmission system or the terrestrial transmission
system is difficult to deploy
Satellite transmission may bring extra delay and therefore timers of signaling plane and user
plane need to be adjusted to prevent transmission delay from causing data loss.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command ADD SAALLNK (CME single configuration:
IUCS Configuration Express > ATM Transport > SAAL Signaling Link; CME
batch modification center: not supported) or MOD SAALLNK (CME single
configuration: IUCS Configuration Express > ATM Transport > SAAL Signaling
Link; CME batch modification center: not supported) to add or modify the settings
of SAAL links on the Iu interface. Modify the values of parameters associated with
satellite transmission, as described in Table 221-1.
NOTE
In the signaling plane of the Iu interface, except that the timer of SAAL links is set to a smaller
value, timers of other links are set to 1s or longer. The delay of satellite transmission is about 600
ms and therefore the settings of timers in other signaling planes do not need to be changed. Timers
of links in the user plane of the Iu interface are also set to 1s or longer and do not need to be changed,
either.
l Verification Procedure
1. Run the BSC6900 MML command LST SAALLNK to check whether the setting of
the timer is modified correctly.
2. Run the BSC6900 MML command DSP SAALLNK to query the status of SAAL
links. The result shows that SAAL link state is AVAILABLE.
l Deactivation Procedure
1. Run the BSC6900 MML command MOD SAALLNK (CME single configuration:
IUCS Configuration Express > ATM Transport > SAAL Signaling Link; CME
batch modification center: not supported) to change associated parameters to the
default values.
----End
Example
//Activating Satellite Transmission on Iu Interface
MOD SAALLNK: SRN=0, SN=0, SAALLNKN=1, CARRYT=NCOPT, CARRYSRN=0,
CARRYSN=14, CARRYNCOPTN=0, SAALLNKT=NNI, CCTMR=800, POLLTMR=300,
IDLETMR=3000, RSPTMR=3000, KEEPTMR=1000;
This section describes how to activate, verify, and deactivate the optional feature WRFD-050501
Clock Synchronization on Ethernet in NodeB.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The feature WRFD-050402 IP Transmission Introduction on Iub Interface must be
configured before this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others
Huawei clock server should support this feature.
Context
This feature provides a solution for clock synchronization in the all-IP network. The clock
synchronization of the base station can be achieved for the operator without changing the existing
data network and introducing additional QoS requirements for the transport network.
Procedure
l NodeB V200R014
Activation Procedure
1. Run the NodeB MML command ADD IPCLKLINK (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer >
IPCLKLNK > IP Clock Link Management; CME batch modification center: not
supported) to add an IP clock link.
2. Run the NodeB MML command SET CLKMODE (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Basic Information > Clock
Source > System Clock Link Management; CME batch modification center: not
supported) to set the working mode of the reference clock source.
Set Clock Working Mode to MANUAL(Manual).
Set Selected Clock Source to IPCLK(IP Clock).
Verification Procedure
1. Run the NodeB MML command DSP IPCLKLINK to query the running status of
all IP clock links.
Expected result: The value of Link Available State is Available.
2. Run the NodeB MML command DSP CLKSTAT to query the status of the system
clock.
Expected result: The value of Current Clock Source State is Normal.
Deactivation Procedure
1. Run the NodeB MML command SET CLKMODE (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Basic Information > Clock
Source > System Clock Link Management; CME batch modification center: not
supported) to set the working mode of the reference clock source. Set Clock Working
Mode to FREE(Free).
2. Run the NodeB MML command RMV IPCLKLINK (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer >
IPCLKLNK > IP Clock Link Management; CME batch modification center: not
supported) to remove a specified IP clock link.
l NodeB V100R014
Activation Procedure
1. Run the NodeB MML command ADD IPCLKLINK (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer >
IPCLKLNK > IP Clock Link Management; CME batch modification center: not
supported) to add an IP clock link.
2. Run the NodeB MML command SET CLKMODE (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Basic Information > Clock
Source > System Clock Link Management; CME batch modification center: not
supported) to set the working mode of the reference clock source.
Set System Clock Working Mode to MANUAL(Manual).
Set Clock Source Type to IPCLK(IP clock source).
Verification Procedure
1. Run the NodeB MML command DSP IPCLKLINK to query the running status of
all IP clock links.
Expected result: The value of IP Clock Link Status is Normal.
2. Run the NodeB MML command DSP CLKSTAT to query the status of the system
clock.
Expected result: The value of Current Clock Source State is Normal.
Deactivation Procedure
1. Run the NodeB MML command SET CLKMODE (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Basic Information > Clock
Source > System Clock Link Management; CME batch modification center: not
supported) to set the working mode of the reference clock source. Set System Clock
Working Mode to FREE(Free).
2. Run the NodeB MML command RMV IPCLKLINK (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer >
IPCLKLNK > IP Clock Link Management; CME batch modification center: not
supported) to remove a specified IP clock link.
----End
Example
l NodeB V200R014
//Activation procedure
ADD IPCLKLINK: ICPT=HW_DEFINED, SN=7, CIP="82.0.1.107",
SIP="82.0.1.128";
SET CLKMODE: MODE=MANUAL, CLKSRC=IPCLK, SYNMODE=OFF;
//Verification procedure
DSP IPCLKLINK:;
DSP CLKSTAT: SN=7;
//Deactivation procedure
SET CLKMODE: MODE=FREE;
RMV IPCLKLINK:;
l NodeB V100R014
//Activation procedure
ADD IPCLKLINK: SRN=0, SN=12, CIP="11.11.11.11", SIP="10.10.12.12",
ICPT=HW_DEFINED;
SET CLKMODE: MODE=MANUAL, CLKSRC=IPCLK, IPMODE=AUTO;
//Verification procedure
DSP IPCLKLINK: SN=12;
DSP CLKSTAT:;
//Deactivation procedure
SET CLKMODE: MODE=FREE;
RMV IPCLKLINK: SRN=0, SN=12;
This section describes how to activate, verify, and deactivate the optional feature WRFD-050502
Synchronous Ethernet.
Prerequisites
l Dependencies on Hardware
Only the BSC6900 supports this feature.
Only the 3900 series base stations support this feature.
l Dependencies on Other Features
Configurations of other features on which this feature depends are complete. This
feature depends on features WRFD-050402 IP Transmission Introduction on Iub
Interface.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others
The synchronous Ethernet technology requires that all the equipments on the clock relay
path must support the synchronous Ethernet.
Context
This feature provides the solution for clock synchronization in all-IP networking scenarios. It
enables the clock extraction and recovery in the physical layer of the Ethernet.
Procedure
l Activation Procedure
1. Run the NodeB MML command ADD SYNCETH (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Basic Information > Clock
Source > Synchronous Ethernet Clock Link Management; CME batch
modification center: not supported) to add a synchronous-Ethernet clock link.
2. Run the NodeB MML command SET CLKMODE (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Basic Information > Clock
Source > System Clock Link Management; CME batch modification center: not
supported) to set the working mode of the reference clock source.
Set Clock Working Mode to MANUAL(Manual).
Set Selected Clock Source to SYNCETH(SyncEth Clock).
l Verification Procedure
1. Run the NodeB MML command DSP CLKSTAT to query the status of the current
clock source.
Expected result: The value of Current Clock Source State is Normal.
l Deactivation Procedure
1. Run the NodeB MML command SET CLKMODE (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Basic Information > Clock
Source > System Clock Link Management; CME batch modification center: not
supported) to set the working mode of the reference clock source. In this step, set
Clock Working Mode to FREE(Free).
2. Run the NodeB MML command RMV SYNCETH (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Basic Information > Clock
Source > Synchronous Ethernet Clock Link Management; CME batch
modification center: not supported) to remove a synchronous-Ethernet clock link.
----End
Example
//Activation procedure
ADD SYNCETH: SN=7, PN=0;
SET CLKMODE: MODE=MANUAL, CLKSRC=SYNCETH;
//Verification procedure
DSP CLKSTAT: SN=7:;
//Deactivation procedure
SET CLKMODE: MODE=FREE;
RMV SYNCETH:;
This section describes how to activate, verify, and deactivate the optional feature WRFD-050425
Ethernet OAM. (This feature cannot be configured using the CME. )
Prerequisites
l Dependency on RNC Hardware
Only BSC6900 supports this feature.
RAN11.0, BTS3812E/AE and DBS3800 can only support IEEE 802.1ag draft 7. 3900
series NodeB can support IEEE 802.3ah and IEEE 802.1ag draft 7.
RAN12.0, BTS3812E/AE, DBS3800, 3900 series NodeB can support both IEEE
802.3ah and IEEE 802.1ag draft 8.
l Dependencies on Other Features
The configurations of the features on which this feature depends are complete. This
feature depends on the feature WRFD-050402 IP Transmission Introduction on the Iub
Interface, or WRFD-050409 IP Transmission Introduction on the Iu Interface, or
WRFD-050410 IP Transmission Introduction on the Iur Interface.
l License
This feature is not under license control.
Context
With the evolution from WCDMA to IPRAN, the Ethernet transmission network is widely used.
As a layer-2 protocols, the Ethernet OAM can report the status of the network on the data link
layer. In this way, the Ethernet can be more efficiently monitored and managed. The Ethernet
OAM functions include detection, notification, verification, and fault location functions. These
faults include the hard faults (such as the link interruption) that can be detected on the physical
layer or the soft faults (such as the fault of the memory or the bridge) that cannot be detected on
the physical layer. The Ethernet OAM plays a significant role in cutting the CAPEX/OPEX cost
and complies with the service level (SLA).
The RAN supports two kinds of Ethernet OAM features, that is, the PPP Ethernet OAM feature
defined by the 802.3ah and the E2E Ethernet OAM defined by 802.1ag.
1. PPP Ethernet OAM
The PPP Ethernet OAM complies with the IEEE 802.3ah protocol. It is the last-mile OAM
solution. It implements the PPP maintenance of the Ethernet through detection, loopback,
link monitoring, and fault detection and is not service, and it is not service-specific, as
shown in Figure 224-1.
Procedure
l Activating the Ethernet OAM 3AH Function
1. Run the BSC6900 MML command ACT EFMAH to activate the Ethernet OAM 3AH
function.
NOTE
The OAM 3AH function on peer equipment must be activated.
l Activating the Ethernet OAM 1AG Function
1. Run the BSC6900 MML command ADD CFMMD to add the Ethernet OAM
maintenance domain (MD). The Ethernet OAM MD consists of bridges and
maintenance equipment. Each MD is associated with a maintenance level. There are
eight maintenance levels, that is level 0 to level 7.
2. Run the BSC6900 MML command ADD CFMMA to add the Ethernet OAM
maintenance association (MA). Each MD can be divided into several MAs. Each MA
corresponds to a service instance identified by the VLAN in the MD.
3. Run the BSC6900 MML command ADD CFMMEP to add an Ethernet OAM
maintenance end point (MEP). You can add different local or remote maintenance
points of different MEP types to the MA.
NOTE
l The MEPID of the RemoteMep configured on the peer equipment must be consistent with
the MEPID of the LocalMep configured on the local equipment.
l MD, MA or MEP must be configured on the peer equipment when the MD, MA or MEP
has be added on BSC6900.
4. Run the BSC6900 MML command ACT CFMCCMTST to activate the Ethernet
OAM unidirectional connectivity detection between the local MEP and the remote
MEP.
l Verifying the Ethernet OAM 3AH Function
1. Activate the Ethernet OAM 3AH function. The Alarm-21371 ETHOAM 3AH
Detection Failure alarm is reported when Ethernet OAM detection fails. The
ALM-21345 Ethernet Link Fault alarm is report when Ethernet OAM detection is
enable, because link on local end and peer end fails.
2. Activate the Ethernet OAM 3AH loopback function. If the loopback succeeds, the
Alarm-21374 ETHOAM 3AH Remote Loopback is reported due to service
congestion.
l Verifying the Ethernet OAM 1AG Function
1. Activate the Ethernet OAM 1AG function. The running of the PING MAC and TRC
MAC fails if the transmission between the local MEP and the remote MEP is faulty
because the local MEP fails to receive the connectivity detection packet from the
remote MEP.
2. OAM 1AG function on the peer equipment must be activated, and the transmission is
functional that the local MEP succeeds to receive the CCM packets from the peer
MEP, the running of the PING MAC and TRC MAC succeeds.
l Deactivating the Ethernet OAM 3AH Function
1. Run the BSC6900 MML command DEA EFMAH to deactivate the Ethernet OAM
3AH function.
l Deactivating the Ethernet OAM 1AG Function
1. Run the BSC6900 MML command DEA CFMCCMTST to deactivate the Ethernet
OAM unidirectional connectivity detection.
2. Run the BSC6900 MML command RMV CFMMD to delete the Ethernet OAM
maintenance domain (MD).
3. Run the BSC6900 MML command RMV CFMMA to delete the Ethernet OAM
maintenance association (MA).
4. Run the BSC6900 MML command RMV CFMMEP to delete the Ethernet OAM
maintenance end point (MEP).
----End
Example
//Activating the Ethernet OAM 3AG function
ACT EFMAH: SRN=0, SN=18, PN=0;
//Activating the Ethernet OAM 1AG function
ADD CFMMD: SRN=0, SN=18, MDIDX=0, MDName="md0";
ADD CFMMA: SRN=0, SN=18, MDIDX=0, VLANID=2, MAIDX=0, MANAME="ma0";
ADD CFMMEP: SRN=0, MAIDX=0, MEPTYPE=LocalMep, MEPID=1, PORTTYPE=ETHER,
SN=18, PN=0;
ADD CFMMEP: SRN=0, MAIDX=0, MEPTYPE=RemoteMep, MEPID=11, SN=18;
ACT CFMCCMTST: SRN=0, SN=18, MAIDX=0, MEPID=1;
//Verifying the Ethernet OAM 1AG function
PING MAC: SRN=0, SN=18, MAIDX=0, SRCMEPID=1, DESTMEPID=11;
TRC MAC: SRN=0, SN=18, MAIDX=0, SRCMEPID=1, DESTMEPID=11;
//Deactivating the Ethernet OAM 3AG function
DEA EFMAH: SRN=0, SN=18, PN=0;
//Deactivating the Ethernet OAM 1AG function
DEA CFMCCMTST: SRN=0, SN=18, MAIDX=0, MEPID=1;
RMV CFMMD: SRN=0, SN=18, MDIDX=0;
RMV CFMMA: SRN=0, SN=18, MAIDX=0;
RMV CFMMEP: SRN=0, SN=18, MAIDX=0, MEPID=11;
RMV CFMMEP: SRN=0, SN=18, MAIDX=0, MEPID=1;
This section describes how to activate, verify, and deactivate the optional feature WRFD-040202
RNC Node Redundancy.
Prerequisites
l Dependencies on Hardware
This feature does not depend on hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others
The Iur, Iu-CS, Iub and Iu-PS interfaces have been configured. For details, see
Configuring the Interfaces.
Context
This feature improves the reliability and robustness of RAN and shortens the service interruption
due to single-point failure in the RNC. In this way, the service quality is improved. With this
feature, a NodeB can be connected to two RNCs and heartbeat detection is performed on the Iur
interface between the two RNCs. When the primary RNC is faulty, the NodeB can be fast
switched to the secondary RNC for service provisioning.
The primary RNC and the secondary RNC form an RNC pool, as shown in Figure 225-1 and
Figure 225-2.
NOTE
l When the serving RNC is faulty, the maximum service capability (such as CS Erlang and PS
throughput) decreases from the combined capability of two RNCs to the capability of one RNC. As a
result, the processing specifications of the network decrease.
l To activate this feature, data configurations related to this feature are required on the RNC and the
NodeB. The CN and M2000 do not require data configurations specific to this feature. You can check
the homing state of the NodeB on the M2000.
Procedure
l Activation Procedure
NOTE
This document uses RNC202, RNC203, and NodeB1 as examples to describe the procedures. Assume
that RNC202 and RNC203 are initially configured as the primary homing and secondary homing
RNC of NodeB1 respectively.
1. Data configurations on the primary homing RNC (RNC202)
a. Run the BSC6900 MML command ADD URNCPOOL (CME single
configuration: UMTS Global Configuration Express > Redundancy Backup
Configuration > RNC Pool; CME batch modification center: not supported) to
add an RNC pool. In this step, set the parameters such as RncPool Index,
RncPool Name, Supporting Auto-Rehoming Switch and so on.
CAUTION
If the license is activated , the primary homing RNC is physically broken down
and Supporting Auto-Rehoming Switch is set to OFF, the feature
WRFD-040300 License Control for Urgency will be activated.
WRFD-040300 License Control for Urgency can be enabled only fifteen times
for each R version for this kind of reason.
CAUTION
If the license is activated , the secondary homing RNC is physically broken down
and Supporting Auto-Rehoming Switch is set to OFF, and the feature
WRFD-040300 License Control for Urgency will be activated.
WRFD-040300 License Control for Urgency can be enabled only fifteen times
for each R version for this kind of reason.
DSP UCELL on the RNC203 LMT. The query result shows that cell 2 is
unavailable due to no control rights.
b. Perform an emulation test of the primary RNC fault.
Run the BSC6900 MML command RST UIU on RNC202 to make RNC202
become faulty.
If the BSC6900 recovers too fast after the BSC6900 MML command RST
UIU is executed, you can remove the cable on the Iu-CS/Iu-PS interface
instead.
c. After RNC203 detects that RNC202 is faulty through the Iur interface, RNC203
takes over the NodeB and initiates cell2 reestablishment.
d. (Optional) When the connection between the NodeB and the primary homing
RNC is disconnected, the secondary homing RNC cannot obtain the NodeB
control rights automatically. To solve this problem, run the BSC6900 MML
command FOC UHOSTNODEB on the RNC203 LMT to manually switch over
the NodeB control rights to the secondary homing RNC.
CAUTION
Switching over NodeB control rights manually disrupts the ongoing services
when the connection between the NodeB and the primary homing RNC is normal.
e. On both the RNC203 LMT and the RNC202 LMT, run the BSC6900 MML
command DSP UCELL. If the query result on the RNC203 LMT shows that cell
2 is operational and the query result on the RNC202 LMT shows that cell 1 is
unavailable due to no control rights, this feature has been activated. Otherwise,
this feature is not activated.
2. Method 2: Verifying services
a. Check whether the heartbeat between RNC202 and RNC203 is normal, as shown
in Figure 225-3.
b. Check that the cell under RNC202 is available, and then use the UE to establish
a CS AMR service, as shown in Figure 225-4 and Figure 225-5.
c. Power off RNC202 when RNC203 works properly. RNC203 then takes over the
NodeB control rights.
d. When RNC202 restores normal services, it takes over the NodeB control rights
again according to the rehoming strategy, and RNC203 releases the NodeB
control rights.
3. Method 3: Verifying this feature on the M2000
a. Create the RNCs and NodeB on the RNC POOL monitor of the M2000. When
creating a NodeB, the M2000 checks the homing state of the NodeB. If the RNC
is the secondary homing RNC of the NodeB, the NodeB cannot be created under
that RNC.
b. When the M2000 starts, it starts NE status subscribing. When the homing state
of the NodeB changes, the RNC reports the NodeB homing state to the M2000.
The M2000 then updates the network topology displayed in the RNC POOL
monitor.
l Deactivation Procedure
1. On RNC202 and RNC203, run the BSC6900 MML command DEA URNCPOOL
(CME single configuration: UMTS GLOBAL Configuration Express >
Redundancy Backup Configuration > RNC Pool. Set active status to
Deactivated; CME batch modification center: not supported) to deactivate the feature.
----End
Example
/*Activation procedure*/
/*Data configuration script on the primary homing RNC side*/
/*Configuring an RNC pool*/
ADD URNCPOOL: RncPoolIndex=0, RncPoolName="redundancy_RNCPOOL";
ADD URNCPOOLMEMBER: RncPoolIndex=0, NrncId=203;
ACT URNCPOOL: RncPoolIndex=0;
//RNC203
DSP UCELL: DSPT=BYCELL, CellId=2;
//RNC202
RST UIU: CnOpIndex=0, CNDOMAINID= ALL_DOMAIN, RSTCNTYPE=ALL_NODES;
//RNC202
DSP UCELL: DSPT=BYCELL, CellId=1;
//RNC203
DSP UCELL: DSPT=BYCELL, CellId=2;
//Deactivating RNC Node Redundancy
//RNC202&RNC203
DEA URNCPOOL: RncPoolIndex=0;
This section describes how to activate, verify, and deactivate the optional feature WRFD-040203
RRU Redundancy.
Prerequisites
l Dependencies on Hardware
BTS3902E does not support this feature.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
Context
RRU redundancy can improve the reliability and robustness of the RAN and shorten the duration
of service disruption caused by an RRU failure, improving service quality.
Procedure
l Activation Procedure
1. If a cell is configured as a MIMO cell or a transmit diversity cell, run the BSC6900
MML command ADD UCELLALGOSWITCH (CME single configuration: UMTS
Cell Configuration Express > Cell Parameters > Cell Algorithm Switches; CME
batch modification center: 3.18 Modifying UMTS Cell Parameters in Batches) or
MOD UCELLALGOSWITCH (CME single configuration: UMTS Cell
Configuration Express > Cell Parameters > Cell Algorithm Switches; CME batch
modification center: 3.18 Modifying UMTS Cell Parameters in Batches). In this
step, set Cell Capability Auto Handle Switch to TX_DIVERSITY_ON_TO_OFF
(TX diversity capability is on to off) or TX_DIVERSITY_OFF_TO_ON(TX
diversity capability is off to on). Both the options can be selected.
2. Run the NodeB MML command ADD LOCELL (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Radio Layer > xx Sector > Locell; CME
batch modification center: 3.17 Modifying Physical NodeB Parameters in
Batches) to ensure the local cell uses two power amplifiers.
l Verification Procedure
1. Run the BSC6900 MML command LST UCELLALGOSWITCH to check that Cell
Capability Auto Handle Switch is set to TX diversity capability is on to off::ON
or TX diversity capability is off to on::ON.
2. Run the NodeB MML command LST LOCELL to query whether the local cell is
configured with two power amplifiers.
l Deactivation Procedure
This feature need not be deactivated.
----End
Example
//Activation procedure
//When a cell is configured as a MIMO and transmit diversity cell, do as
follows:
ADD UCELLALGOSWITCH: CellId=1, NBMUlCacAlgoSelSwitch=ALGORITHM_SECOND,
NBMDlCacAlgoSelSwitch=ALGORITHM_SECOND,
CellCapacityAutoHandleSwitch=TX_DIVERSITY_ON_TO_OFF-1&TX_DIVERSITY_OFF_TO
_ON-1;
//Or
MOD UCELLALGOSWITCH: CellId=1,
CellCapacityAutoHandleSwitch=TX_DIVERSITY_ON_TO_OFF-1&TX_DIVERSITY_OFF_TO
_ON-1;
//Ensure that the local cell uses two power amplifiers.
ADD LOCELL: LOCELL=0, STN=0, SECN=0, SECT=REMOTE_SECTOR, RADIUS=10000,
HORAD=150, TTW=TRUE, SRN1=60, SRN2=61, SN2=0, ULFREQ=9610, DLFREQ=10560,
MXPWR=430, HISPM=TRUE, SPR=250, RMTCM=FALSE, VAM=FALSE;,
//Verification procedure
//Querying the cell algorithm switch
LST UCELLALGOSWITCH: CellId=1;
//Checking whether the local cell is configured with two power
amplifiers
LST LOCELL: MODE=LOCALCELL, LOCELL=10;
This section describes how to activate, verify, and deactivate the optional feature WRFD-021302
Iu Flex.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others
The MSC and the serving GPRS support node (SGSN) support this feature.
Context
This feature allows one BSC6900 to connect to multiple MSCs and/or SGSNs, and these CS/
PS domain nodes can form different pools that serve the same pool area.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UOPERATORCFGPARA (CME single
configuration: UMTS Global Configuration Express > Operator Configuration >
RNC Operator Configuration Information; CME batch modification center: not
supported). In this step, set Feature Supporting Mode of CS Domain to
SUPP_IUFLEX, set Feature Supporting Mode of PS Domain to
SUPP_IUFLEX, and set Length of CS NRI in bits and Length of PS NRI in bits
to appropriate values.
2. Configure the Iu interface transmission between BSC6900 and multiple core networks
(CNs) by referring to Configuring the Interfaces.
3. Run the BSC6900 MML command ADD UCNNODE (CME single configuration:
UMTS Global Configuration Express > Core Network > UMTS CN Node; CME
batch modification center: not supported) to add multiple CN nodes for an operator
according to the network plan.
4. Run the BSC6900 MML command ADD UNRIGLBCNIDMAP (CME single
configuration: UMTS Global Configuration Express > Core Network > NRI And
CN Node Mapping Information; CME batch modification center: not supported).
In this step, set Cn Operator Index, CN node ID, and Network resource identity
to configure the mapping relationships between NRI and CN nodes.
5. Optional: Run the BSC6900 MML command ADD UIMSIIDNNSCNIDMAP
(CME single configuration: UMTS Global Configuration Express > Core
Network > IMSI Route Parameters and CN Node Mapping Information; CME
batch modification center: not supported) to configure the mapping relationships
between international mobile subscriber identity (IMSI) ranges and CN nodes.
After configuring the mapping relationships, the RNC routes the UE whose IMSI is
within the IMSI range to the specified CN.
l Verification Procedure
1. Enable the UE to access a cell and register in the cell.
2. According to the mapping relationships between IMSI ranges and CN nodes and the
load balance algorithm, the RNC selects a CN node for the UE, and the UE registers
successfully.
3. Then, if the UE initiates a service, the RNC routes the UE to the corresponding CN
node according to the mapping relationships between NRI and CN nodes.
l Deactivation Procedure
1. Run the BSC6900 MML command RMV UIMSIIDNNSCNIDMAP (CME single
configuration: UMTS Global Configuration Express > Core Network > IMSI
Route Parameters and CN Node Mapping Information; CME batch modification
center: not supported) to remove IMSI Route Parameters and CN Node Mapping
Information (Keep Mapping of one CN Node).
2. Run the BSC6900 MML command RMV UNRIGLBCNIDMAP (CME single
configuration: UMTS Global Configuration Express > Core Network > NRI And
CN Node Mapping Information; CME batch modification center: not supported) to
remove NRI and all of CN Node Mapping Information.
3. Run the BSC6900 MML command RMV UCNNODE (CME single configuration:
UMTS Global Configuration Express > Core Network > UMTS CN Node; CME
batch modification center: not supported) to remove CN Node (Keep one CN Node).
4. Run the BSC6900 MML command SET UOPERATORCFGPARA (CME single
configuration: UMTS Global Configuration Express > Operator Configuration >
RNC Operator Configuration Information; CME batch modification center: not
supported) to deactivate this feature. In this step, set Feature Supporting Mode of
CS Domain to SUPP_NONE, set Feature Supporting Mode of PS Domain to
SUPP_NONE.
----End
Example
//Activating Iu Flex
//Configuring the RNC supporting Iu Flex with Length of CS NRI in bits and
Length of PS NRI in bits set to appropriate values
SET UOPERATORCFGPARA: CnOpIndex=1, CsNriCfgMode=SUPP_IUFLEX,
PsNriCfgMode=SUPP_IUFLEX, CSNRILength=5, PSNRILength=5;
//Configuring the mapping relationship between NRI and the first CN node
ADD UNRIGLBCNIDMAP: CnOpIndex=1, CNId=17, NRI=8;
//Configuring the mapping relationship between NRI and the second CN node
ADD UNRIGLBCNIDMAP: CnOpIndex=1, CNId=18, NRI=9;
//Configuring the mapping relationship between the IMSI range and the
first CN node
ADD UIMSIIDNNSCNIDMAP: ImsiRtMin=0, ImsiRtMax=666, CnOpIndex=1, CNId=17;
//Configuring the mapping relationship between the IMSI range and the
second CN node
ADD UIMSIIDNNSCNIDMAP: ImsiRtMin=667, ImsiRtMax=999, CnOpIndex=1,
CNId=18;
//Deactivating Iu Flex
RMV UIMSIIDNNSCNIDMAP: ImsiRtMin=667, ImsiRtMax=999, CnOpIndex=1,
CNId=18;
RMV UNRIGLBCNIDMAP: CnOpIndex=1, CNId=18, NRI=9;
RMV UNRIGLBCNIDMAP: CnOpIndex=1, CNId=17, NRI=8;
RMV UCNNODE: CnOpIndex=1, CNId=18;
SET UOPERATORCFGPARA: CnOpIndex=1, CsNriCfgMode=SUPP_NONE,
PsNriCfgMode=SUPP_NONE;
This section describes how to activate, verify, and deactivate the optional feature WRFD-021306
Iu Flex Load Distribution Management.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The feature WRFD-021302 Iu Flex has been configured before this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The CN supports dynamic capacity management and load redistribution.
Context
This feature enables load balancing and load redistribution among multiple CN nodes when Iu
Flex is deployed. The BSC6900 supports dynamic and static management of CN capacity and
status information.
Procedure
l Activation Procedure
Configuring load balancing in static capacity mode
1. Run the BSC6900 MML command ADD UCNNODE (CME single configuration:
UMTS Global Configuration Express > Core Network > UMTS CN Node;
CME batch modification center: not supported). In this step, set Capability of CN
Node to an appropriate value. The BSC6900 performs load balancing between CN
nodes based on the configured CN capacities.
Configuring load balancing in dynamic capacity mode
Load balancing in dynamic capacity mode takes effect only when the BSC6900 is
connected to Huawei CN and the preceding switches related to Iu Flex are turned on.
Configuring load redistribution based on NullNRI
1. Run the BSC6900 MML command MOD UCNNODE (CME single
configuration: UMTS Global Configuration Express > Core Network > UMTS
CN Node; CME batch modification center: not supported). In this step, set Status
of CN Node to OFFLOAD.
2. Run the BSC6900 MML command SET UOPERATORCFGPARA (CME single
configuration: UMTS Global Configuration Express > Operator
Configuration > RNC Operator Configuration Information; CME batch
modification center: not supported). In this step, set NullNRI VALUE to an
appropriate value based on the network plan.
Configuring load redistribution based on Block CN Node
1. Run the BSC6900 MML command MOD UCNNODE (CME single
configuration: UMTS Global Configuration Express > Core Network > UMTS
CN Node; CME batch modification center: not supported). In this step, set Status
of CN Node to NORMAL and select the RSVDBIT1_BIT1 check box under the
parameter Reserved parameter 1.
l Verification Procedure
Verifying load balancing in static capacity mode
1. Run the BSC6900 MML command DSP UCNNODE to query the capacity ratio
of CN nodes.
2. Check the following performance counters on the M2000 to verify that the
BSC6900 performs load balancing based on the preconfigured CN capacity:
Performance counters for CS service setup:
VS.IU.LdBalRtCS.IMSI
VS.IU.LdBalRtCS.InValidNRI
VS.IU.LdBalRtCS.IMEI
Performance counters for PS service setup:
VS.IU.Load.RoutePS.IMSI
VS.IU.Load.RoutePS.NRI
VS.IU.Load.RoutePS.IMEI
Verifying load balancing in dynamic capacity mode
1. Run the BSC6900 MML command DSP UCNNODE to query the capacity ratio
of CN nodes.
2. On the BSC6900 LMT, choose Trace > UMTS Services to initiate Uu and Iu
interface message tracing.
3. Check the traced messages. If the CN sends the BSC6900 an INFORMATION
TRANSFER INDICATION message, the dynamic CN capacity ratio is updated
and used. If the CN does not send any INFORMATION TRANSFER
INDICATION message to the BSC6900, the static CN capacity ratio is used.
4. Check the following performance counters on the M2000 to verify that the
BSC6900 performs load balancing based on the dynamic CN capacity ratio:
Performance counters for CS service setup:
VS.IU.LdBalRtCS.IMSI
VS.IU.LdBalRtCS.InValidNRI
VS.IU.LdBalRtCS.IMEI
Performance counters for PS service setup:
VS.IU.Load.RoutePS.IMSI
VS.IU.Load.RoutePS.NRI
VS.IU.Load.RoutePS.IMEI
Verifying load redistribution based on NullNRI
1. On the BSC6900 LMT, choose Trace > UMTS Services to initiate Uu and Iu
interface message tracing.
2. Power off the UE. The PTMSI of the UE is assigned by SGSN1.
3. Set SGSN1 to the OFFLOAD state and SGSN2 to the NORMAL state on the RNC.
4. Set SGSN1 to the OFFLOAD state on SGSN1.
5. Power on the UE and the UE makes an attach request. Check the traced Iu interface
messages. The expected result is as follows:
The BSC6900 routes the RRC_INIT_DIRECT_TRANSFER message to
SGSN1 based on NULL NRI. The attach reception message from SGSN1
contains NULL NRI and non-broadcasting location areas.
After receiving the non-broadcasting location areas, the UE sends a new routing
area update (RAU) request and contains NULL NRI in the
RRC_INIT_DIRECT_TRANSFER message. The BSC6900 routes the
RRC_INIT_DIRECT_TRANSFER message to SGSN2, of which the state
is not OFFLOAD, based on NULL NRI.
Verifying load redistribution based on Block CN Node
1. On the BSC6900 LMT, choose Trace > UMTS Services to initiate Uu and Iu
interface message tracing.
2. Power off the UE. The PTMSI of the UE is assigned by SGSN1.
3. Set SGSN1 to the BLOCK state and SGSN2 to the NORMAL state on the RNC.
4. Power on the UE and the UE makes an attach request. Check the
RRC_INIT_DIRECT_TRANSFER message traced on the Iu interface.
Expected result: The RRC_INIT_DIRECT_TRANSFER message contains
NRI of SGSN1. The BSC6900 routes the RRC_INIT_DIRECT_TRANSFER
message to SGSN2 because SGSN1 is in the BLOCK state.
l Deactivation Procedure
Deactivating load balancing in static capacity mode
Example
//Activating Iu Flex Load Distribution Management
//Configuring Load balancing in static capacity mode
ADD UCNNODE: CnOpIndex=1, CNId=17, CNDomainId=CS_DOMAIN, Dpx=2,
CNProtclVer=R6, CNLoadStatus=NORMAL, AvailCap=1000,
TnlBearerType=ATM_TRANS, Switch3GPP25415CR0125=OFF;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010203
Transmit Diversity. Transmit diversity enables the NodeB to provide twice the number of RF
DL channels compared with no transmit diversity.
Prerequisites
l Dependencies on Hardware
TX diversity requires the NodeB to provide two times RF channel resources compared
with no TX diversity mode. In TX diversity mode, the UE must support diversity
reception, STTD, TSTD, and CLD1.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
l Others
The UE must support diversity reception, STTD, TSTD, and CLD1.
Context
l The feature supports STTD, TSTD, and CLD1 to effectively improve the reception
performance of the UE.
l The transmit diversity feature improves terminal performance in special circumstances.
Especially when multipath fading is not obvious and the UE is not moving fast, capacity
and coverage can be significantly improved. The investment can be reduced while the same
QoS is guaranteed. In this way, operators can reduce the CAPEX and the OPEX.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command MOD UCELLSETUP (CME single
configuration: UMTS Cell Configuration Express > Cell Basic Information > Cell
Basic Information; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches) to set the transmit diversity mode. Transmit diversity mode
consists of Space Time Transmit Diversity (STTD) mode and closed loop TX diversity
mode 1 (CP1).
Example
//Activation procedure
MOD UCELLSETUP: CellId=2, TxDiversityInd=TRUE, STTDSupInd=STTD_Supported,
CP1SupInd=CP1_Supported, ClosedLoopTimeAdjustMode=OFFSET1,
DpchDivModforOther=STTD, FdpchDivModforOther=STTD,
DpchDivModforMIMO=STTD, FdpchDivModforMIMO=STTD, DivModforDCHSDPA=STTD;
ADD SEC: STN=0, SECN=1, SECT=REMOTE_SECTOR, ANTM=2, DIVM=COMMON_MODE,
ANT1SRN=60, ANT1N=R0A, ANT2SRN=61, ANT2N=R0A;
ADD LOCELL: LOCELL=1, STN=0, SECN=1, SECT=REMOTE_SECTOR, TTW=TRUE,
SRN1=60, SRN2=61, ULFREQ=9700, DLFREQ=10650, MXPWR=430, HISPM=FALSE,
RMTCM=FALSE, VAM=FALSE;
//Verification procedure
DSP LOCELL: LOCELL=1;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010209
4-Antenna Receive Diversity.
Prerequisites
l Dependencies on Hardware
The RX diversity requires the Node B to provide enough RF channels and demodulation
resources that can match the number of diversity antennas.
BTS3902E can't support this feature.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
Context
l Compared with 2-Antenna Receive Diversity, 4-Antenna Receive Diversity provides the
NodeB with twice the number of RF UL channels. In this way, a bigger UL coverage gain
can be obtained.
l 4-antenna Receive Diversity improves the receiver sensitivity and the uplink coverage, so
that the CAPEX can be reduced.
Procedure
l Activation Procedure
1. Run the NodeB MML command ADD SEC (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Radio Layer > Sector; CME batch
modification center: not supported). In this step, set Antenna Magnitude to 4. Set
Antenna Channel1 No., Antenna Channel2 No., Antenna Channel3 No., Antenna
Channel4 No., their respective cabinet numbers, and subrack numbers.
2. Run the NodeB MML command ADD ULGROUP (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Radio Layer > UL/DL BB
Resource Group > ULGROUP; CME batch modification center: not supported). In
Example
l NodeB V200R014
//Activation procedure
ADD SEC: STN=0, SECN=0, SECT=LOCAL_SECTOR, ANTM=4, ANT1CN=0,
ANT1SRN=4, ANT1N=N0A, ANT2CN=0, ANT2SRN=4, ANT2N=N0B, ANT3CN=0,
ANT3SRN=4, ANT3N=N1A, ANT4CN=0, ANT4SRN=4, ANT4N=N1B;
This section describes how to activate, verify, and deactivate the optional feature WRFD-021308
Extended Cell Coverage up to 200km.
Prerequisites
l Dependencies on Hardware
All types of baseband boards support this feature. However, only the WBBPb, WBBPd
(3900 series NodeB), EBBI, EBOI, EULP, EULPd (BTS3812E/AE), and EBBC/
EBBCd/EBBM (DBS3800) support remote cell groups.
BTS3902E can't support this feature.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
Context
l This feature enables the operator to use a few NodeBs to extend the cell coverage.
l This feature extends the cell coverage to very remote areas with the fewest sites.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command ADD UAICH (CME single configuration: UMTS
Cell Configuration Express > Channel Configuration > AICH; CME batch
modification center: not supported). In this step, set AICH Transmission Timing to
1.
2. Run the BSC6900 MML command ADD UPRACHBASIC (CME single
configuration: UMTS Cell Configuration Express > Channel Configuration >
PRACH Basic Information; CME batch modification center: not supported). In this
step, select available RACH sub channels in the cell from the RACH Sub Channel
No. list.
3. Run the BSC6900 MML command MOD UCELL (CME single configuration:
UMTS Cell Configuration Express > Cell Basic Information > Cell Basic
l Only 3 sub channels can be set for every cell, and no repeated sub channel exists. The 3 sub
channels need to be fixed as follows:
l sub-channel 0, sub-channel 1 and sub-channel 2
l sub-channel 4, sub-channel 5 and sub-channel 6
l sub-channel 8, sub-channel 9 and sub-channel 10
l When adding logical cell on BSC6900, the parameter Time Offset needs to be set to CHIP0,
CHIP256 or CHIP512.
l Verification Procedure
1. Run the NodeB MML command LST REMOTECELLGRP to check that the remote
cell group is configured.
2. Run the NodeB MML command LST LOCELL to check that the local cell is set to
a remote cell and that Remote Cell Mode is set to TRUE.
l Deactivation Procedure
This feature does not need to be deactivated.
----End
Example
//Activation procedure
//Configuration on the BSC6900 side
ADD UAICH: CELLID=1;
ADD UPRACHBASIC: CellId=1, PhyChId=4, PreambleSignatures=SIGNATURE0-1,
RACHSubChNo=SUBCHANEL0-1&SUBCHANEL1-1&SUBCHANEL2-1, Constantvalue=-23,
PreambleRetransMax=20, PowerRampStep=2, CTFCSize=BIT2;
MOD UCELL: CellId=2, MaxTxPower=430;
ADD UPCPICH: CELLID=1, PHYCHID=2, PCPICHPOWER=330, MAXPCPICHPOWER=346,
MINPCPICHPOWER=313;
//Configuration on the NodeB side
ADD REMOTECELLGRP: REMOTECELLGRPINDEX=1, REMOTECELLGRPNAME="test";
ADD LOCELL: LOCELL=1, STN=1, SECN=1, SECT=LOCAL_SECTOR, CN1=0, SRN1=4,
SN1=0, ULFREQ=9700, DLFREQ=10600, MXPWR=430, HISPM=FALSE,
This section describes how to activate, verify, and deactivate the optional feature WRFD-020138
HSUPA Coverage Enhancement at UE Power Limitation.
Prerequisites
l Dependencies on Hardware
There is no requirement for BSC6900or NodeB.
The UE supports this feature.
l Dependencies on Other Features
The feature WRFD-010612 HSUPA Introduction Package must be configured before
this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others
The UE needs to support 3GPP Release 8 or later. It also needs to support improved
EUL power control at UE power limitation.
Context
Compared with the traditional power compression technology, this feature provides an enhanced
power compression function. This feature optimizes the size of a data block and the E-DPDCH
power offset, improving the HSUPA performance at cell edge.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to select
l Deactivation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to clear
PC_HSUPA_COVER_EN_AT_POLIMIT_SWITCH check box from Power
Control Switch to deactivate the feature.
----End
Example
//Activation procedure
This section describes how to activate, verify, and deactivate the optional feature WRFD-021001
Flexible frequency bandwidth of UMTS carrier.
Prerequisites
l Dependencies on Hardware
For 4.6M~5M(including 4.6M), all the RF module can support this feature.
For 4.0M~4.6M(excluding 4.6M), only 850M/1900M RRU3804, 850M WRFU, MRFU
V1/V2 and MRRU V1/V2, WRFUd, RRU3828, RRU3829, RRU3928, RRU3929,
MRFUd, MRFUe can support this feature.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
To help an operator adapt to insufficient frequency resources, Huawei supports flexible
frequency spacing. In network planning, to address insufficient bandwidth resources, an operator
can plan a frequency spacing that is lower than the frequency spacing in the case of 5.0 MHz
UMTS carrier bandwidth. Accordingly, the effective bandwidth of the RRU or RFU carrier is
adjusted so that the carrier works in a suitable status with suitable algorithms and parameters.
In this way, network performance on a low- spacing frequency is optimized as much as possible.
When deploying a UMTS site, one needs to adjust the minimal effective bandwidth of a UMTS
carrier based on the GSM frequency configuration. Otherwise, TRX alarms may occur or
network performance may deteriorate.
Procedure
l Activation Procedure
1. Before configuring the effective bandwidth of the carrier, run the NodeB MML
command LST RRU (CME single configuration: NodeB Configuration Express >
IUB_NodeB > Device Panel > RXU Topology) to check that an RRU is configured
for the cell that requires setting of carrier effective bandwidth. If an RRU is not
configured, run the NodeB MML command ADD RRU (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Device Panel > TOPO > Right
click RXU CHAIN > Add RXU Board; CME batch modification center: not
supported) to add an RRU.
2. Run the NodeB MML command SET FREQBWH (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Device Panel > RUX Topology >
Right click RRU > RXU Board Property > Radio Frequency Unit; CME batch
modification center: not supported) to set the minimal effective bandwidth of the RRU
carrier (parameter: Frequency Min Bandwidth).
l Verification Procedure
Run the NodeB MML command LST FREQBWH to query the effective bandwidth of the
RRU carrier and check the returned message.
If... Then...
l Deactivation Procedure
Run the NodeB MML command SET FREQBWH (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Device Panel > RUX Topology > Right click
RRU > RXU Board Property > Radio Frequency Unit; CME batch modification center:
not supported) to set the RRU effective bandwidth to 5000 Hz so that the standard
configuration of the system is restored.
----End
Example
//Activation procedure
SET FREQBWH: CN=0, SRN=60, SN=0, FMBWH=4200;
//Verification procedure
LST FREQBWH;
//Deactivation procedure
SET FREQBWH: CN=0, SRN=60, SN=0, FMBWH=5000;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010206
High Speed Access.
Prerequisites
l Dependencies on Hardware
All boards of the 3900 series base stations support High Speed Access.
All boards of the DBS3800 support High Speed Access.
All boards, except the NBBI and NULP, of the BTS3812E and BTS3812AE support
the high speed access feature.
l Dependencies on Other Features
This feature does not depend on other features.
l License
This feature is not under license control.
Context
The time-selective fading caused by the Doppler effect of a fast-moving UE increases the BER
and affects the signals received by the NodeB. The high speed access feature provides the
automatic frequency control (AFC) function for the uplink, reducing the Doppler effect and
offering reliable services for the UE in high-speed movement.
NOTE
l The local sectors, remote sectors and distributed sectors support the high speed access feature.
l When the HULP, HBBI, HBBU, or WBBPa is configured to support the high speed access feature, the
capability for the board to carry access channels decreases. Each board can support the access channels
of only one cell. In addition, the board in a common four-channel demodulation mode does not support
high speed access.
l When the WBBPb, WBBPd, EBBI, EBOI, EULP, EULPd, EBBC, or EBBCd is configured to support
the high speed access feature, the capability of the board does not decrease. The board supports high
speed access in any demodulation mode.
CAUTION
To enable the high speed access feature in the cells carrying services, deactivate these cells,
modify these cells, and then activate these cells. This process disrupts the ongoing services.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command DEA UCELL (CME single configuration: UMTS
Cell Configuration Express > Cell Basic Information > Cell Basic Information.
Set Validation indication to Deactivated; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches) to deactivate the logical cell of local
cell.
2. Run the NodeB MML command MOD LOCELL (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Radio Layer > xx Sector > Locell; CME
batch modification center: 3.17 Modifying Physical NodeB Parameters in
Batches) to modify the attributes of the specified local cell. In this step, set, High
Speed Movement Mode to TRUE. Set Speed Rate as required.
3. Run the BSC6900 MML command ACT UCELL (CME single configuration: UMTS
Cell Configuration Express > Cell Basic Information > Cell Basic Information.
Set Validation indication to Activated; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches) to activate the logical cell of local
cell.
l Verification Procedure
1. Run the NodeB MML command LST LOCELL to query the configuration
information about the local cell. The query result is returned on the LMT. Check that
the values of High Speed Movement Mode and Speed Rate match the configuration.
l Deactivation Procedure
1. Run the BSC6900 MML command DEA UCELL (CME single configuration: UMTS
Cell Configuration Express > Cell Basic Information > Cell Basic Information.
Set Validation indication to Deactivated; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches) to deactivate the logical cell of local
cell.
2. Run the NodeB MML command MOD LOCELL (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Radio Layer > xx Sector > Locell; CME
batch modification center: 3.17 Modifying Physical NodeB Parameters in
Batches) to modify the attributes of the local cell. In this step, set, High Speed
Movement Mode to FALSE.
3. Run the BSC6900 MML command ACT UCELL (CME single configuration: UMTS
Cell Configuration Express > Cell Basic Information > Cell Basic Information.
Set Validation indication to Activated; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches) to activate the logical cell of local
cell.
----End
Example
//Activation procedure
DEA UCELL: CellId=1;
235
Demodulation of Signals from Multiple RRUs in
Configuring Independent
One Cell
This section describes how to activate, verify, and deactivate the optional feature WRFD-021350
Independent Demodulation of Signals from Multiple RRUs in One Cell.
Prerequisites
l Dependencies on Hardware
This feature supports only DBS3900 series base stations.
The WBBPb, WBBPd, or WBBPf board needs to be configured.
l Dependencies on Other Features
This feature is mutually exclusive to the following features:
WRFD-010203 Transmit Diversity
WRFD-010209 4-Way Receive Diversity
WRFD-010684 2x2 MIMO
WRFD-021308 Extended Cell Coverage up to 200km
WRFD-010701 Uplink Enhanced CELL_FACH
WRFD-010692 HSUPA FDE
WRFD-020102 Load Measurement (based on the report of actual service load)
WRFD-140215 Dynamic Configuration of HSDPA CQI Feedback Period
WRFD-140216 Load-based Uplink Target BLER Configuration
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
l Precautions
In multi-RRU cell scenarios, this feature reduces handovers between cells and increases
cell capacity and cell throughput.
This feature cannot be used if a base station is configured with the feature transmit
diversity, 4-Antenna Receive Diversity, or multiple-input multiple-output (MIMO).
This feature is suitable for high-speed scenarios, such as freeways, high-speed railways,
and F1 racing arenas.
l Data Preparation
Configuring an uplink baseband resource group
Parameter Name Parameter ID Recommended Date Source
Parameter
Settings
Configuring a sector
Parameter Name Parameter ID Recommended Data Source
Parameter
Settings
Procedure
l Activation Procedure
Scenario 1: 1TX+2RX configuration
Figure 235-1 shows the hardware configuration of this scenario. The following
procedure assumes that RRU 1 is installed at slot 60 and RRU 2 is at slot 61.
1. Run the NodeB MML command ADD BRD (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Device Panel > Universal Satellite
Control Unit; CME batch modification center: not supported) to add a baseband
processing board.
2. Run the NodeB MML command ADD ULGROUP (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Radio Layer > UL/DL BB
Resource Group > ULGROUP; CME batch modification center: not supported)
to add an uplink resource group.
3. Run the NodeB MML command ADD DLGROUP (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Radio Layer > UL/DL BB
Resource Group > DLGROUP; CME batch modification center: not supported)
to add a downlink resource group.
4. Run the NodeB MML command ADD RRUCHAIN (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Device Panel > Right click
TOPO > Add RXU Chain; CME batch modification center: not supported) to add
an RRU chain.
5. Run the NodeB MML command ADD RRU (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Device Panel > TOPO > Right click
RXU CHAIN > Add RXU Board; CME batch modification center: not supported)
to add an RRU to the RRU chain.
6. Run the NodeB MML command ADD SITE (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Radio Layer > Site; CME batch
modification center: not supported) to add a site.
7. Run the NodeB MML command ADD SEC (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Radio Layer > Sector; CME batch
modification center: not supported) to add a sector.
8. Run the NodeB MML command ADD LOCELL (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Radio Layer > xx Sector >
Locell; CME batch modification center: 3.17 Modifying Physical NodeB
Parameters in Batches) to add a local cell.
9. Run the BSC6900 MML command ADD UCELLQUICKSETUP (CME single
configuration: Main View > Right click NodeB > Add UMTS Cell; CME batch
modification center: not supported) to add a cell.
Scenario 2: 1TX+1RX configuration
Figure 235-2 shows the hardware configuration of this scenario. The following
procedure assumes that RRU 1 to RRU 3 are installed in slot 60 to 62, respectively.
1. Run the NodeB MML command ADD BRD (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Device Panel > Universal Satellite
Control Unit; CME batch modification center: not supported) to add a baseband
processing board.
2. Run the NodeB MML command ADD ULGROUP (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Radio Layer > UL/DL BB
Resource Group > ULGROUP; CME batch modification center: not supported)
to add an uplink resource group.
3. Run the NodeB MML command ADD DLGROUP (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Radio Layer > UL/DL BB
Resource Group > DLGROUP; CME batch modification center: not supported)
to add a downlink resource group.
4. Run the NodeB MML command ADD RRUCHAIN (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Device Panel > Right click
TOPO > Add RXU Chain; CME batch modification center: not supported) to add
an RRU chain.
5. Run the NodeB MML command ADD RRU (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Device Panel > TOPO > Right click
RXU CHAIN > Add RXU Board; CME batch modification center: not supported)
to add an RRU to the RRU chain.
6. Run the NodeB MML command ADD SITE (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Radio Layer > Site; CME batch
modification center: not supported) to add a site.
7. Run the NodeB MML command ADD SEC (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Radio Layer > Sector; CME batch
modification center: not supported) to add a sector.
8. Run the NodeB MML command ADD LOCELL (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Radio Layer > xx Sector >
Locell; CME batch modification center: 3.17 Modifying Physical NodeB
Parameters in Batches) to add a local cell.
9. Run the BSC6900 MML command ADD UCELLQUICKSETUP (CME single
configuration: Main View > Right click NodeB > Add UMTS Cell; CME batch
modification center: not supported) to add a cell.
Scenario 3: 1TX+1RX and 1TX+2RX hybrid configuration
Figure 235-3 shows the hardware configuration of this scenario. The following
procedure assumes that RRU 1 to RRU 4 are installed in slot 60 to 63, respectively.
1. Run the NodeB MML command ADD BRD (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Device Panel > Universal Satellite
Control Unit; CME batch modification center: not supported) to add a baseband
processing board.
2. Run the NodeB MML command ADD ULGROUP (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Radio Layer > UL/DL BB
Resource Group > ULGROUP; CME batch modification center: not supported)
to add an uplink resource group.
3. Run the NodeB MML command ADD DLGROUP (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Radio Layer > UL/DL BB
Resource Group > DLGROUP; CME batch modification center: not supported)
to add a downlink resource group.
4. Run the NodeB MML command ADD RRUCHAIN (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Device Panel > Right click
TOPO > Add RXU Chain; CME batch modification center: not supported) to add
an RRU chain.
5. Run the NodeB MML command ADD RRU (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Device Panel > TOPO > Right click
RXU CHAIN > Add RXU Board; CME batch modification center: not supported)
to add an RRU to the RRU chain.
6. Run the NodeB MML command ADD SITE (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Radio Layer > Site; CME batch
modification center: not supported) to add a site.
7. Run the NodeB MML command ADD SEC (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Radio Layer > Sector; CME batch
modification center: not supported) to add a sector.
NOTE
If an RRU requires only one antenna, set the unused antenna to NULL for the RRU by
running the ADD SEC (CME single configuration: NodeB Configuration Express >
IUB_NodeB > Radio Layer > Sector; CME batch modification center: not supported)
command.
8. Run the NodeB MML command ADD LOCELL (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Radio Layer > xx Sector >
Locell; CME batch modification center: 3.17 Modifying Physical NodeB
Parameters in Batches) to add a local cell.
9. Run the BSC6900 MML command ADD UCELLQUICKSETUP (CME single
configuration: Main View > Right click NodeB > Add UMTS Cell; CME batch
modification center: not supported) to add a cell.
l Verification Procedure
1. Run the NodeB MML command LST SEC to query configured sectors.
Expected result: The value of Sector Type is MULTIRRU_SECTOR
(MULTIRRU_SECTOR).
2. Run the NodeB MML command DSP LOCELL to query the local cell.
Expected result: The value of Local Cell Status is Local Cell Available.
3. Optional: After the corresponding logical cell is activated, perform drive tests to
check for coverage holes and weak coverage areas.
l Deactivation Procedure
Deactivate the corresponding logical cell on the RNC, and then remove the local cell and
sector on the NodeB. After this feature is deactivated, the released resources, such as the
RF components and baseband processing board, can be used for other cells.
1. Run the BSC6900 MML command DEA UCELL (CME single configuration: UMTS
Cell Configuration Express > Cell Basic Information > Cell Basic Information.
Set Validation indication to Deactivated; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches) to deactivate a specified logical cell
on the RNC.
2. Run the NodeB MML command RMV LOCELL (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Radio Layer > xx Sector > Locell; CME
batch modification center: not supported) to remove a specified local cell of the
NodeB.
3. Run the NodeB MML command RMV SEC (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Radio Layer > Sector; CME batch
modification center: not supported) to remove a specified sector of the NodeB.
----End
Example
//Activation procedure
//Scenario 1: 1TX+2RX configuration
ADD BRD: SN=3, BT=WBBP, WM=FDD, HCE=FULL;
ADD ULGROUP: ULGROUPN=0, DEMMODE=DEM_2_CHAN, SNE1=3;
ADD DLGROUP: DLGROUPN=0, SNE1=3;
ADD RRUCHAIN: RCN=1, TT=CHAIN, BM=COLD, HCN=0, HSRN=0, HSN=3, HPN=0;
ADD RRU: CN=0, SRN=60, SN=0, TP=TRUNK, RCN=1, PS=0, RT=MRRU, RS=UO,
RXNUM=2, TXNUM=1;
ADD RRU: CN=0, SRN=61, SN=0, TP=TRUNK, RCN=1, PS=1, RT=MRRU, RS=UO,
RXNUM=2, TXNUM=1;
This section describes how to activate, verify, and deactivate the optional feature WRFD-020302
Inter Frequency Hard Handover Based on Coverage.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The UE supports relevant measurements and the handover procedure.
Context
This feature introduces inter-frequency hard handover triggered by Active Set quality
measurement event 2D or by Uplink Radio Link Qos or emergency blind handover triggered by
event 1F.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, select
HO_INTER_FREQ_HARD_HO_SWITCH from the HandOver Switch drop-
down list.
2. Run the BSC6900 MML command ADD UINTERFREQNCELL (CME single
configuration: UMTS Cell Configuration Express > Neighboring Cell > Inter-
frequency Neighboring Cell; CME batch modification center: not supported) to add
an inter-frequency neighboring cell.
3. Run the BSC6900 MML command ADD UCELLINTERFREQHOCOV (CME
single configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Oriented Coverage Based Inter-frequency Handover Measurement Algorithm
Parameters; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches) (cell level) or SET UINTERFREQHOCOV (CME single
configuration: UMTS Radio Global Configuration Express > HandOver
Parameter Configuration > RNC Oriented Coverage Based Inter-frequency
Handover Measurement Algorithm Parameters; CME batch modification center:
3.15 Modifying RNC Parameters in Batches) (RNC level) to configure parameters
related to coverage-based inter-frequency hard handover.
l Verification Procedure
1. Attenuate signals in the current cell that the UE accesses to trigger reporting of event
2D by the UE.
2. Click to display Uu Interface Trace on the BSC6900 LMT.
3. Check whether the RNC has sent the UE an RRC_MEAS_CTRL message and the
traced message contains thresholds for triggering events 2D and 2F and the reporting
mode.
4. Check whether the RNC has sent the UE an RRC_MEAS_RPRT message and the
traced message contains an event 2D measurement report shown in Figure 236-1.
5. After the event 2D measurement report is reported, check whether the RNC has sent
the UE an RRC_MEAS_CTRL message and the traced message contains the
information element interFrequencyMeasurement, as shown in Figure 236-2.
l Deactivation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, deselect
HO_INTER_FREQ_HARD_HO_SWITCH from HandOver Switch.
----End
Example
//Activating Inter Frequency Hard Handover Based on Coverage
SET UCORRMALGOSWITCH: HoSwitch=HO_INTER_FREQ_HARD_HO_SWITCH-1
ADD UINTERFREQNCELL:RncId=1, CellId=1, NCellRncId=9, NCellId=100,
CIOOffset=0, SIB11Ind=TRUE, SIB12Ind=FALSE, TpenaltyHcsReselect=D0,
HOCovPrio=1, BlindHOFlag=FALSE, NPrioFlag=FALSE;
ADD UCELLINTERFREQHOCOV: CellId=1,
InterFreqReportMode=PERIODICAL_REPORTING, InterFreqMeasTime=60;
//Deactivating Inter Frequency Hard Handover Based on Coverage
SET UCORRMALGOSWITCH: HoSwitch=HO_INTER_FREQ_HARD_HO_SWITCH-0;
This section describes how to activate, verify, and deactivate the optional feature WRFD-020304
Inter Frequency Hard Handover Based on DL QoS.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
The feature WRFD-020302 Inter Frequency Hard Handover Based on Coverage must
be configured before this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
When the load of services is high in a cell and downlink QoS decreases, this feature enables the
UE to be handed over to an inter-frequency cell, guaranteeing QoS requirements.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to activate the inter-frequency hard handover.
2. Run the BSC6900 MML command ADD UINTERFREQNCELL (CME single
configuration: UMTS Cell Configuration Express > Neighboring Cell > Inter-
frequency Neighboring Cell; CME batch modification center: not supported) to add
an inter-frequency neighboring cell.
3. Run the BSC6900 MML command ADD UCELLINTERFREQHOCOV (CME
single configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Example
//Activating Inter Frequency Hard Handover Based on DL QoS
SET UCORRMALGOSWITCH: HoSwitch=HO_INTER_FREQ_HARD_HO_SWITCH-1;
ADD UINTERFREQNCELL:RncId=1, CellId=1, NCellRncId=9, NCellId=100,
CIOOffset=0, SIB11Ind=TRUE, SIB12Ind=FALSE, TpenaltyHcsReselect=D0,
HOCovPrio=1, BlindHOFlag=FALSE, NPrioFlag=FALSE;
ADD UCELLQOSHO: CellId=111, DlRscpQosHyst=5, DLQosMcTimerLen=20,
ULQosMcTimerLen=20;
SET UQOSACT: BEQosPerform=YES, BeDlAct1=InterFreqHO;
SET UQOSACT: AMRQosPerform=YES, DlQosAmrInterFreqHoSwitch=YES,
DlQosWAmrInterFreqHoSwitch=YES;
SET UQOSACT: VPQosPerform=YES, DlQosVpInterFreqHoSwitch=YES;
//Deactivating Inter Frequency Hard Handover Based on DL QoS
RMV UCELLQOSHO: CellId=111;
SET UQOSACT: BEQosPerform=NO; or SET UQOSACT: BEQosPerform=YES,
BeDlAct1=None, BeDlAct2=None, BeDlAct3=None;
SET UQOSACT: AMRQosPerform=NO; or SET UQOSACT: AMRQosPerform=YES,
DlQosAmrInterFreqHoSwitch=NO, DlQosWAmrInterFreqHoSwitch=NO;
SET UQOSACT: VPQosPerform=NO; or SET UQOSACT: VPQosPerform=YES,
DlQosVpInterFreqHoSwitch=NO;
This section describes how to activate, verify, and deactivate the optional feature
WRFD-02060501 SRNS Relocation (UE Not Involved). (This feature cannot be configured
using the CME. )
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The feature WRFD-020605 SRNS Relocation Introduction Package has been
configured before this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others Prerequisites
The CN supports this feature.
Both the SRNC and the DRNC support this feature.
Context
This feature supports the SRNS relocation procedure based on the standard Iu interface defined
by 3GPP specifications. The static SRNS relocation procedure does not involve the UE and radio
connections are not affected during the relocation. Therefore, static SRNS relocation is an
optimal relocation mode.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command ADD DEVIP to add a device IP address to an
interface board.
2. Run the BSC6900 MML command ADD IPOAPVC to add an Internet Protocol over
ATM (IPoA) permanent virtual circuit (PVC). In this step:
Call drops do not occur during SRNS relocation if all the following messages are
traced:
Example
//Activating SRNS Relocation (UE Not Involved)
PsBeProcType=CORRM_SRNSR_PSBE_RELOC;
MOD UNRNC: NRncId=2,
SHOTRIG=CS_SHO_SWITCH-1&HSPA_SHO_SWITCH-1&NON_HSPA_SHO_SWITCH-1,
PsBeProcType=CORRM_SRNSR_PSBE_RELOC;
This section describes how to activate, verify, and deactivate the optional feature
WRFD-02060502 SRNS Relocation with Hard Handover.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The configurations of the features on which this feature depends are complete. This
feature depends on the feature WRFD-021304 RAN Sharing Introduction Package.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The SRNC and the DRNC must support this feature simultaneously.
The CN must support this feature simultaneously.
Context
When the Iur interface is unavailable, this feature enables the UE to move between RNCs.
This feature is enabled when the Iur interface does not exist, or the resources for the connection
setup on the Iur interface are insufficient.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command ADD UINTRAFREQNCELL (CME single
configuration: UMTS Cell Configuration Express > Neighboring Cell > Intra-
frequency Neighboring Cell; CME batch modification center: not supported) to add
an intra-frequency neighboring cell.
2. UE1 and UE2 are in idle mode and camp on Cell 111.
l Deactivation Procedure
This feature does not need to be deactivated.
----End
Example
//Activating SRNS Relocation with Hard Handover
//Turn on HHO cross IUR trigger, and set Handover Type for PS BE Traffic
to CORRM_SRNSR_PSBE_RELOC
MOD UNRNC: NRncId=2, HHOTRIG=ON, PsBeProcType=CORRM_SRNSR_PSBE_RELOC;
This section describes how to activate, verify, and deactivate the optional feature
WRFD-02060503 SRNS Relocation with Cell/URA Update.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The configurations of the features on which this feature depends are complete. This
feature depends on the feature WRFD-020605 SRNS Relocation Introduction Package.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The CN and the DRNC must support this feature simultaneously.
Context
If the Iur interface supports the Iur-CCH, inter-RNC cell/URA update normally does not trigger
the relocation. Instead, the relocation is triggered through the static relocation procedure. SNSR
relocation triggered by cell/URA update is performed when the following conditions are met:
The SNSR relocation can be triggered by cell reselection of UEs in the CELL_FACH,
CELL_PCH, or URA_PCH state. The relocation is started after the Cell Update or URA Update
message from the UE is forwarded from the target RNC to the source RNC over the Iur interface.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to set the following switches in the Dynamic resource
allocation switch parameter:
Set DRA_DCCC_SWITCH to 1.
Set DRA_PS_BE_STATE_TRANS_SWITCH to 1.
Set DRA_PS_NON_BE_STATE_TRANS_SWITCH to 1.
2. Run the BSC6900 MML command SET UUESTATETRANSTIMER (CME single
configuration: UMTS Radio Global Configuration Express > UE State Transition
Parameter Configuration > RNC StateTrans Timer Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches) to set BE DCH
to FACH Transition Timer to 10.
3. Run the BSC6900 MML command MOD UNRNC (CME single configuration: IUR
Configuration Express > Neighbouring RNC > Neighboring RNC; CME batch
modification center: not supported) to set IUR CCH support flag to NO and
Handover Type for PS BE Traffic to CORRM_SRNSR_PSBE_RELOC.
l Verification Procedure
1. The Iur interface between RNC1 and RNC2 is working properly. On the HLR, set the
UE to support background services.
2. UE1 and UE2 are in idle mode and camp on Cell 111.
3. Trigger state transition so that the UE transits to the CELL_FACH, CELL_PCH, or
URA_PCH state.
4. Initiate standard interface tracing on the RNC LMT to perform the verifying procedure
as follows:
If the following messages are displayed, you can infer that no call drops occur during
the transition.
RNC1->RNC2: RNSAP_RELOCATION_COMMIT
l Deactivation Procedure
This feature does not need to be deactivated.
----End
Example
//Activating SRNS Relocation with Cell/URA Update.
SET UCORRMALGOSWITCH:
DraSwitch=DRA_DCCC_SWITCH-1&DRA_PS_BE_STATE_TRANS_SWITCH-1&DRA_PS_NON_BE_
STATE_TRANS_SWITCH-1;
SET UUESTATETRANSTIMER: BeD2FStateTransTimer=10;
MOD UNRNC: NRncId=2, SuppIurCch=NO, PsBeProcType=CORRM_SRNSR_PSBE_RELOC;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010615
Multiple RAB Package (PS RAB 2).
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The CN node and UE must have the corresponding multi-RAB support capability.
Context
With the Multiple RAB feature, operators have relatively diversified choices of service solutions.
If the Multiple RAB feature is enabled, a large quantity of services can be provided for the upper
layers. Huawei products support the following solutions with more than one PS RAB:
l Combination of two PS services
l Combination of one CS service and two PS services
l Combination of three PS services
l Combination of one CS service and three PS services
l Combination of four PS services
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Example
//Activating Multiple RAB Package (PS RAB 2).
SET UCORRMALGOSWITCH: CfgSwitch=CFG_MULTI_RAB_SWITCH-1;
//Deactivating Multiple RAB Package (PS RAB 2).
SET UCORRMALGOSWITCH: CfgSwitch=CFG_MULTI_RAB_SWITCH-0;
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061501 Combination of Two PS Services.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The configurations of the features on which this feature depends are complete. This
feature depends on the feature WRFD-010615 Multiple RAB Package (PS RAB 2).
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The UE supports the combination of two PS services.
The CN node and UE must have the corresponding multi-RAB support capability.
Context
With the Multiple RAB feature, operators have relatively diversified choices of service solutions.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to select the CFG_MULTI_RAB_SWITCH check box
under the Channel configuration strategy switch parameter.
l Verification Procedure
Example
//Activating Combination of Two PS Services.
SET UCORRMALGOSWITCH: CfgSwitch=CFG_MULTI_RAB_SWITCH-1;
//Deactivating Combination of Two PS Services.
SET UCORRMALGOSWITCH: CfgSwitch=CFG_MULTI_RAB_SWITCH-0;
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061502 Combination of One CS Service and Two PS Services.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The configurations of the features on which this feature depends are complete. This
feature depends on the feature WRFD-010615 Multiple RAB Package (PS RAB 2).
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The UE supports the combination of One CS Service and Two PS Services.
The CN node and UE must have the corresponding multi-RAB support capability.
Context
With the Multiple RAB feature, operators have relatively diversified choices of service solutions.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to select the CFG_MULTI_RAB_SWITCH check box
under the Channel configuration strategy switch parameter.
l Verification Procedure
Example
//Activating Combination of One CS Service and Two PS Services.
SET UCORRMALGOSWITCH: CfgSwitch=CFG_MULTI_RAB_SWITCH-1;
//Deactivating Combination of One CS Service and Two PS Services.
SET UCORRMALGOSWITCH: CfgSwitch=CFG_MULTI_RAB_SWITCH-0;
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061503 Combination of Three PS Services.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The configurations of the features on which this feature depends are complete. This
feature depends on the feature WRFD-010615 Multiple RAB Package (PS RAB 2).
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The UE supports the Combination of Three PS Services.
The CN node and UE must have the corresponding multi-RAB support capability.
Context
With the Multiple RAB feature, operators have relatively diversified choices of service solutions.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to select the CFG_MULTI_RAB_SWITCH check box
under the Channel configuration strategy switch parameter.
l Verification Procedure
Example
//Activating Combination of Three PS Services.
SET UCORRMALGOSWITCH: CfgSwitch=CFG_MULTI_RAB_SWITCH-1;
//Deactivating Combination of Three PS Services.
SET UCORRMALGOSWITCH: CfgSwitch=CFG_MULTI_RAB_SWITCH-0;
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061504 Combination of One CS Service and Three PS Services.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The configurations of the features on which this feature depends are complete. This
feature depends on the feature WRFD-010615 Multiple RAB Package (PS RAB 2).
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The UE supports the combination of one CS service and three PS services.
The CN node and UE have the corresponding multi-RAB support capability.
Context
With the Multiple RAB feature, operators have relatively diversified choices of service solutions.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to select the CFG_MULTI_RAB_SWITCH check box
under the Channel configuration strategy switch parameter.
l Verification Procedure
Example
//Activating Combination of One CS Service and Three PS Services.
SET UCORRMALGOSWITCH: CfgSwitch=CFG_MULTI_RAB_SWITCH-1;
//Deactivating Combination of One CS Service and Three PS Services.
SET UCORRMALGOSWITCH: CfgSwitch=CFG_MULTI_RAB_SWITCH-0;
This section describes how to activate, verify, and deactivate the optional feature
WRFD-01061505 Combination of Four PS Services.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The configurations of the features on which this feature depends are complete. This
feature depends on the feature WRFD-010615 Multiple RAB Package.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The UE supports the combination of Four PS Services.
The CN node and UE have the corresponding multi-RAB support capability.
Context
RAN11.0 supports up to four PS RABs per user. A typical application of Multi-RAB is VoIP
plus BE service where VoIP may need up to three RABs to transmit SIP signaling, Real-Time
Transport Protocol (RTP) (voice), and Real-Time Control Protocol (RTCP) (media monitoring)
respectively, as shown in Figure 246-1.
RAN11.0 supports four PS RABs per user, and the service combination VoIP + BE is supported.
Other service combination like 4PS BE is also supported.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to select the CFG_MULTI_RAB_SWITCH check box
under the Channel configuration strategy switch parameter.
2. Run the BSC6900 MML command SET UFRCCHLTYPEPARA (CME single
configuration: UMTS Radio Global Configuration Express > Basic Resource
Control Parameter Configuration > Channel Type Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches) command to set
the VOIP channel type parameter to DCH(UL_DCH,DL_DCH).
NOTE
The BSC6900 defines the default value of the VOIP channel type parameter. Retain the default value
in normal situations.
l Verification Procedure
1. Initiate Iu interface tracing on the BSC6900 LMT.
2. Connect the UE to the portable computer so as to use the UE as a modem.
3. Establish a VoIP service on the UE. View the
"RANAP_RAB_ASSIGNMENT_REQ" message traced on the Iu interface. If you
find that the CN assigns three RABs at the same time, you can infer that the VoIP
service is established successfully. (If RTCP is assigned, SIP signaling and RTP must
be assigned at the same time.)
4. On the portable computer, connect to an FTP server and download data. Verify that
the data is downloaded normally.
l Deactivation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to clear the CFG_MULTI_RAB_SWITCH check box
under the Channel configuration strategy switch parameter.
----End
Example
//Activating Combination of Four PS Services
SET UCORRMALGOSWITCH: CfgSwitch=CFG_MULTI_RAB_SWITCH-1;
SET UFRCCHLTYPEPARA: VoipChlType=DCH;
//Deactivating Combination of Four PS Services
SET UCORRMALGOSWITCH: CfgSwitch=CFG_MULTI_RAB_SWITCH-0;
This section describes how to activate, verify, and deactivate the optional feature WRFD-020103
Inter Frequency Load Balance.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The two optional features WRFD-010610 HSDPA Introduction Package and
WRFD-010612 HSUPA Introduction Package have been configured before this feature
is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature enables some UEs in a cell to be handed over to the inter-frequency same-coverage
cells if the cell is in the basic congestion state. The purpose is to reduce the load of this cell.
l Precautions
None
l Data Preparation
Procedure
l Activation Procedure
1. Enable load reshuffling (LDR) algorithms.
Enabling uplink load reshuffling on the Uu interface
a. Run the Run the BSC6900 MML command ADD UCELLALGOSWITCH
(CME single configuration: UMTS Cell Configuration Express > Cell
Parameters > Cell Algorithm Switches; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches). In this step, select the
UL_UU_LDR(Uplink UU LDR Algorithm) check box under the parameter
Switch for Cell Load Control.
Enabling downlink load reshuffling on the Uu interface
a. Run the Run the BSC6900 MML command ADD UCELLALGOSWITCH
(CME single configuration: UMTS Cell Configuration Express > Cell
Parameters > Cell Algorithm Switches; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches). In this step, select the
DL_UU_LDR(Downlink UU LDR Algorithm) check box under the parameter
Switch for Cell Load Control.
Enabling load reshuffling based on cell code resources
a. Run the Run the BSC6900 MML command ADD UCELLALGOSWITCH
(CME single configuration: UMTS Cell Configuration Express > Cell
Parameters > Cell Algorithm Switches; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches). In this step, select the
CELL_CODE_LDR(Code LDR Algorithm) check box under the parameter
Switch for Cell Load Control.
Enabling NodeB-level or cell group-level load reshuffling based on credit resources
a. Run the Run the BSC6900 MML command SET ULDCALGOPARA (CME
single configuration: UMTS Radio Global Configuration Express > Load
Control Parameter Configuration > RNC Configuration of Load Control;
CME batch modification center: 3.15 Modifying RNC Parameters in
Batches). In this step, select the NodeB-level
NODEB_CREDIT_LDR_SWITCH(NodeB Credit LDR Switch) or cell
group-level LCG_CREDIT_LDR_SWITCH(Local Cell Group Credit LDR
Switch) check box under the parameter load control algorithm switch.
b. Run the Run the BSC6900 MML command ADD UNODEBALGOPARA
(CME single configuration: NodeB Configuration Express > IUB_RNC >
NodeB Basic Information > NodeB Algorithm Parameters; CME batch
modification center: 3.16 Modifying Logical NodeB Parameters in Batches).
In this step, select the NodeB-level NODEB_CREDIT_LDR(NodeB Credit
LDR Algorithm) or cell group-level LCG_CREDIT_LDR(LCG Credit LDR
Algorithm) check box under the parameter NodeB LDC algorithm switch.
2. Run the Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME
single configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to enable inter-frequency handover. In this command, select
the HO_ALGO_LDR_ALLOW_SHO_SWITCH and
HO_INTER_FREQ_HARD_HO_SWITCH check boxes under the parameter
HandOver Switch.
3. Run the Run the BSC6900 MML command ADD UINTERFREQNCELL (CME
single configuration: UMTS Cell Configuration Express > Neighboring Cell >
Inter-frequency Neighboring Cell; CME batch modification center: not supported)
to add an inter-frequency neighboring cell supporting blind handover, or to add an
inter-frequency neighboring cell supporting measurement by setting the parameter
DrdOrLdrFlag to an appropriate value.
4. Run the Run the BSC6900 MML command ADD
UCELLINTERFREQHONCOV (CME single configuration: UMTS Cell
Configuration Express > Cell Parameters > Cell Oriented None-Coverage Based
Inter-frequency Handover Measurement Algorithm Parameters; CME batch
modification center: 3.18 Modifying UMTS Cell Parameters in Batches) (cell level)
or SET UINTERFREQHONCOV (CME single configuration: UMTS Radio
Global Configuration Express > HandOver Parameter Configuration > RNC
Oriented None-Coverage Based Inter-frequency Handover Measurement
Algorithm Parameters; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) (RNC level) to set parameters related to load-based inter-
RAT hard handovers to appropriate values based on the network plan.
5. For a load-based inter-frequency handover that is based on measurement, run the Run
the BSC6900 MML command MOD UCELLLDR (CME single configuration:
UMTS Cell Configuration Express > Cell Parameters > Cell LDR Algorithm
Parameters; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches). In this step, set InterFreq Load Handover Method
Selection to MEASUREHO(MEASUREHO).
6. Set LDR-related thresholds based on the network plan.
For uplink and downlink load reshuffling on the Uu interface, run the Run the
BSC6900 MML command MOD UCELLLDM (CME single configuration:
UMTS Cell Configuration Express > Cell Parameters > Cell Oriented LDM
Algorithm Parameters; CME batch modification center: 3.18 Modifying UMTS
Cell Parameters in Batches). In this step, set the following LDR-related
thresholds: UL LDR trigger threshold, UL LDR release threshold, DL LDR
trigger threshold, DL LDR release threshold, and DlLdTrnsHysTime.
For uplink and downlink load reshuffling on the Uu interface and load reshuffling
based on cell code resources, run the Run the BSC6900 MML command MOD
UCELLLDR (CME single configuration: UMTS Cell Configuration Express >
Cell Parameters > Cell LDR Algorithm Parameters; CME batch modification
center: 3.18 Modifying UMTS Cell Parameters in Batches). In this step, set the
following LDR-related threshold: Cell LDR SF reserved threshold.
For NodeB-level or cell group-level load reshuffling based on credit resources, run
the Run the BSC6900 MML command MOD UNODEBLDR (CME single
configuration: NodeB Configuration Express > IUB_RNC > NodeB Basic
Information > NodeB LDR Algorithm Parameters; CME batch modification
center: 3.16 Modifying Logical NodeB Parameters in Batches). In this step, set
the following LDR-related threshold: UL LDR Credit SF reserved threshold.
7. For load reshuffling based on cell code resources, run the Run the BSC6900 MML
command MOD UCELLLDR (CME single configuration: UMTS Cell
Configuration Express > Cell Parameters > Cell LDR Algorithm Parameters;
CME batch modification center: 3.18 Modifying UMTS Cell Parameters in
Batches) to allow inter-frequency handovers in cases of code resource congestion. In
this step, set Code congestion select inter-freq indication to TRUE(TRUE).
8. Run the Run the BSC6900 MML command SET ULDCPERIOD (CME single
configuration: UMTS Radio Global Configuration Express > Load Control
Parameter Configuration > RNC Oriented LDC Algorithm Cycle Length; CME
batch modification center: 3.15 Modifying RNC Parameters in Batches). In this
step, set the LDR period LDR period timer length to an appropriate value.
9. For uplink and downlink load reshuffling on the Uu interface and load reshuffling
based on cell code resources, run the Run the BSC6900 MML command MOD
UCELLLDR (CME single configuration: UMTS Cell Configuration Express >
Cell Parameters > Cell LDR Algorithm Parameters; CME batch modification
center: 3.18 Modifying UMTS Cell Parameters in Batches). In this step, set the DL
LDR second action and DL LDR first action and set other parameters related to the
LDR action based on the network plan.
10. For NodeB-level or cell group-level load reshuffling based on credit resources, run
the Run the BSC6900 MML command MOD UNODEBLDR (CME single
configuration: NodeB Configuration Express > IUB_RNC > NodeB Basic
Information > NodeB LDR Algorithm Parameters; CME batch modification
center: 3.16 Modifying Logical NodeB Parameters in Batches). In this step, select
the InterFreqLDHO(inter-freq load handover) check box under the parameter UL
LDR first action and set other parameters related to the LDR action based on the
network plan.
l Verification Procedure
1. Run the following BSC6900 to check whether this feature has been activated.
LST UCELLALGOSWITCH
LST UCELLLDR
LST UCELLLDM
LST ULDCPERIOD
LST UCORRMALGOSWITCH
LST UINTERFREQNCELL
LST UCELLINTERFREQHONCOV (cell level)
LST UINTERFREQHONCOV (RNC level)
LST ULDCALGOPARA
LST UNODEBALGOPARA
LST UNODEBLDR
2. Check the value of the counter VS.LCC.LDR.InterFreq (Number of UEs Performing
Inter-Frequency Load Handovers in Basic Congestion for Cell). If the values is not 0,
this feature has been activated.
l Deactivation Procedure
1. Disabling load reshuffling algorithms
Disabling uplink LDR on the Uu interface
a. Run the Run the BSC6900 MML command MOD UCELLALGOSWITCH
(CME single configuration: UMTS Cell Configuration Express > Cell
Parameters > Cell Algorithm Switches; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches). In this step, clear the
UL_UU_LDR(Uplink UU LDR Algorithm) check box under the parameter
Switch for Cell Load Control.
Disabling downlink LDR on the Uu interface
a. Run the Run the BSC6900 MML command MOD UCELLALGOSWITCH
(CME single configuration: UMTS Cell Configuration Express > Cell
Parameters > Cell Algorithm Switches; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches). In this step, clear the
DL_UU_LDR(Downlink UU LDR Algorithm) check box under the parameter
Switch for Cell Load Control.
Disabling load reshuffling based on cell code resources
a. Run the Run the BSC6900 MML command MOD UCELLALGOSWITCH
(CME single configuration: UMTS Cell Configuration Express > Cell
Parameters > Cell Algorithm Switches; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches). In this step, clear the
CELL_CODE_LDR(Code LDR Algorithm) check box under the parameter
Switch for Cell Load Control.
Disabling NodeB-level or cell-level load reshuffling based on credit resources
a. Run the Run the BSC6900 MML command SET ULDCALGOPARA (CME
single configuration: UMTS Radio Global Configuration Express > Load
Control Parameter Configuration > RNC Configuration of Load Control;
CME batch modification center: 3.15 Modifying RNC Parameters in
Batches). In this step, clear the NodeB-level
NODEB_CREDIT_LDR_SWITCH(NodeB Credit LDR Switch) or cell
group-level LCG_CREDIT_LDR_SWITCH(Local Cell Group Credit LDR
Switch) check box under the parameter load control algorithm switch.
b. Run the Run the BSC6900 MML command MOD UNODEBALGOPARA
(CME single configuration: NodeB Configuration Express > IUB_RNC >
NodeB Basic Information > NodeB Algorithm Parameters; CME batch
modification center: 3.16 Modifying Logical NodeB Parameters in Batches).
In this step, clear the NodeB-level NODEB_CREDIT_LDR(NodeB Credit
LDR Algorithm) or cell group-level LCG_CREDIT_LDR(LCG Credit LDR
Algorithm) check box under the parameter NodeB LDC algorithm switch.
2. Run the Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME
single configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to disable inter-frequency handover. In this command, clear
the HO_ALGO_LDR_ALLOW_SHO_SWITCH and
HO_INTER_FREQ_HARD_HO_SWITCH check boxes under the parameter
HandOver Switch.
3. Run the Run the BSC6900 MML command MOD UCELLLDR (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell LDR
Algorithm Parameters; CME batch modification center: 3.18 Modifying UMTS
Cell Parameters in Batches) to prohibit inter-frequency handovers in cases of code
resource congestion. In this step, set Code congestion select inter-freq indication to
FALSE(FALSE).
4. Restore the parameter settings modified in the activation procedure.
----End
Example
//Activating Inter Frequency Load Balance
MOD UCELLALGOSWITCH: CellId=111,
NBMLdcAlgoSwitch=UL_UU_LDR-1&DL_UU_LDR-1&CELL_CODE_LDR-1&CELL_CREDIT_LDR-
1;
SET UCORRMALGOSWITCH:
HoSwitch=HO_ALGO_LDR_ALLOW_SHO_SWITCH-1&HO_INTER_FREQ_HARD_HO_SWITCH-1;
ADD UINTERFREQNCELL: RNCId=11, CellId=111, NCellRncId=22, NCellId=222,
SIB11Ind=TRUE, SIB12Ind=FALSE, TpenaltyHcsReselect=D0, BlindHoFlag=FALSE,
NPrioFlag=FALSE, DrdOrLdrFlag=TRUE, InterNCellQualReqFlag=FALSE;
ADD UCELLINTERFREQHONCOV: CellId=111, InterFreqFilterCoef=D3,
Hystfor2C=6, TrigTime2C=D640, InterFreqCovHOThdEcN0=-16,
InterFreqMeasTime=60, PeriodFor2C=4, AmntOfRpt2C=5;
MOD UCELLLDR: CellId=111, InterFreqLDHOMethodSelection=MEASUREHO;
MOD UCELLLDM: CellId=111, UlLdrTrigThd=55, UlLdrRelThd=45,
DlLdrTrigThd=70, DlLdrRelThd=60, DlLdTrnsHysTime=1000;
MOD UCELLLDR: CellId=111, CellLdrSfResThd=SF8;
MOD UCELLLDR: CellId=111, CodeCongSelInterFreqHoInd=TRUE;
SET ULDCPERIOD: LdrPeriodTimerLen=10;
MOD UCELLLDR: CellId=111, DlLdrFirstAction=InterFreqLDHO,
DlInterFreqHoCellLoadSpaceThd=20, DlInterFreqHoBWThd=200000;
SET ULDCALGOPARA:
LdcSwitch=NODEB_CREDIT_LDR_SWITCH-1&LCG_CREDIT_LDR_SWITCH-1;
ADD UNODEBALGOPARA: IDTYPE=BYID, NodeBId=10,
NodeBLdcAlgoSwitch=NODEB_CREDIT_LDR-1&LCG_CREDIT_LDR-1;
MOD UNODEBLDR: IDTYPE=BYID, NodeBId=10, UlLdrFirstAction=InterFreqLDHO,
UlLdrCreditSfResThd=SF8, UlInterFreqHoCeLDRSpaceThd=SF8;
//Deactivating Inter Frequency Load Balance
MOD UCELLALGOSWITCH: CellId=111,
NBMLdcAlgoSwitch=UL_UU_LDR-0&DL_UU_LDR-0&CELL_CODE_LDR-0&CELL_CREDIT_LDR-
0;
SET UCORRMALGOSWITCH:
HoSwitch=HO_ALGO_LDR_ALLOW_SHO_SWITCH-0&HO_INTER_FREQ_HARD_HO_SWITCH-0;
MOD UCELLLDR: CellId=111, CodeCongSelInterFreqHoInd= FALSE;
SET ULDCALGOPARA:
LdcSwitch=NODEB_CREDIT_LDR_SWITCH-0&LCG_CREDIT_LDR_SWITCH-0;
MOD UNODEBALGOPARA: IDTYPE=BYID, NodeBId=11,
NodeBLdcAlgoSwitch=NODEB_CREDIT_LDR-0&LCG_CREDIT_LDR_SWITCH-0;
MOD UNODEBLDR: IDTYPE=BYID, NodeBId=10, UlLdrFirstAction=NoAct;
This section describes how to activate, verify, and deactivate the optional feature WRFD-020114
Domain Specific Access Control (DSAC).
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others
Only the UEs of R6 (or later) can support this function.
DSAC is a feature specified in 3GPP Release 6, and therefore only the UEs of Release
6 or later support this feature.
Context
DSAC specifies the UE access restriction based on the domain type (CS, PS, or CS+PS). The
feature can be triggered either manually or automatically.
Procedure
l Activation Procedure
1. To activate manual DSAC, run the BSC6900 MML command ADD
UCELLDSACMANUALPARA (CME single configuration: UMTS Cell
Configuration Express > Cell Parameters > The Parameters of The Manually
Triggered DSAC Algorithm in the Cell; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches).
l Deactivation Procedure
1. To deactivate manual DSAC, run the BSC6900 MML command RMV
UCELLDSACMANUALPARA (CME single configuration: UMTS Cell
Configuration Express > Cell Parameters > The Parameters of The Manually
Triggered DSAC Algorithm in the Cell; CME batch modification center: not
supported).
2. To deactivate automatic DSAC, run the BSC6900 MML command SET
UDSACAUTOALGO (CME single configuration: UMTS Radio Global
Configuration Express > Access Restriction Algorithm Parameters
Configuration > The Parameters of the Automatically Triggered DSAC
Algorithm; CME batch modification center: 3.15 Modifying RNC Parameters in
Batches). In this step, set Switch for auto DSAC to OFF.
----End
Example
//Activating DSAC
ADD UCELLDSACMANUALPARA: CellId=223, CnOpIndex=0, CsRestriction=TRUE,
PsRestriction=TRUE, RestrictionType=RestrictionFlexible, NumberOfACs=4,
AcRange=AC0-1&AC1-1&AC2-1&AC3-1&AC4-1&AC5-1&AC6-1&AC7-1&AC8-1&AC9-1&AC10-
0&AC11-0&AC12-0&AC13-0&AC14-0&AC15-0, AcRstrctIntervalLen=10;
SET UDSACAUTOALGO: DsacAutoSwitch=ON, CsRestriction=TRUE,
PsRestriction=TRUE, NumberOfACs=2,
AcRange=AC0-1&AC1-1&AC2-1&AC3-1&AC4-1&AC5-1&AC6-1&AC7-1&AC8-1&AC9-1&AC10-
0&AC11-0&AC12-0&AC13-0&AC14-0&AC15-0, AcIntervalOfCells=1,
AcRstrctIntervalLen=10;
//Deactivating DSAC
RMV UCELLDSACMANUALPARA: CellId=223, CnOpIndex=0;
SET UDSACAUTOALGO: DsacAutoSwitch=OFF;
This section describes how to activate, verify, and deactivate the optional feature WRFD-020160
Enhanced Multiband Management.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The following features have been configured before this feature is activated:
WRFD-020110 Multi Frequency Band Networking Management and
WRFD-020400 DRD Introduction Package when traffic steering is implemented
among inter-frequency cells
WRFD-020110 Multi Frequency Band Networking Management and
WRFD-020103 Inter-Frequency Load Balance when load sharing is performed
among inter-frequency cells
If a feature is not activated, the corresponding function is unavailable in the multi-
frequency band networking solution. Features can be configured according to
operator requirements.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
In a multiband network, the cells that work in different frequency bands have different coverage
areas. In this case, blind handovers may lead to call drops. When this feature is enabled, handover
decisions are made based on inter-frequency measurement results. This increases the handover
success rate.
In inter-frequency traffic steering, each cell is configured with the priority for carrying a type
of service (R99 RT, R99 NRT, HSPA, and others). After the RAB is set up, inter-band
measurement is performed to ensure that a UE accesses the cell with the highest priority.
In inter-band load sharing, load reshuffling (LDR) may trigger a load-based inter-frequency
handover after RAB setup. A target cell is selected based on the quality measurement of cells.
Only the cell that meets the quality requirement is selected. Before RAN14.0, measurement-
based inter-band handovers for inter-band load balancing are triggered only by basic congestion
of power resources. In RAN14.0, inter-band handovers can also be triggered by basic congestion
of uplink credit resources. This balances uplink credit resources between cell groups or NodeBs
and increases uplink credit resource utilization.
l Precautions
None
l Data Preparation
Procedure
l Activation Procedure
Configuring this feature based on traffic steering
1. Run the Run the BSC6900 MML command MML command SET UDRD (CME
single configuration: UMTS Radio Global Configuration Express > Directed
Retry Parameter Configuration > RNC-Oriented DRD Algorithm
Parameters; CME batch modification center: 3.15 Modifying RNC Parameters
in Batches). In this step, set Measurement-Based DRD Switch to ON.
2. Run the Run the BSC6900 MML command MML command MOD
UINTERFREQNCELL (CME single configuration: UMTS Cell Configuration
Express > Neighboring Cell > Inter-frequency Neighboring Cell; CME batch
modification center: not supported). In this step, set DrdOrLdrFlag to TRUE
(Send).
Configuring this feature based on load sharing
1. Run the Run the BSC6900 MML command MML command MOD
UINTERFREQNCELL (CME single configuration: UMTS Cell Configuration
Express > Neighboring Cell > Inter-frequency Neighboring Cell; CME batch
modification center: not supported). In this step, set DrdOrLdrFlag to TRUE
(Send).
2. Run the Run the BSC6900 MML command MML command MOD
UCELLLDR (CME single configuration: UMTS Cell Configuration Express >
Cell Parameters > Cell LDR Algorithm Parameters; CME batch modification
center: 3.18 Modifying UMTS Cell Parameters in Batches). In this step, set
InterFreq Load Handover Method Selection to MEASUREHO
(MEASUREHO).
3. Run the BSC6900 MML commandSET UMCDRD (CME single configuration:
UMTS Radio Global Configuration Express > Directed Retry Parameter
Configuration > RNC Based Measurement DRD Algorithm Parameters;
CME batch modification center: 3.15 Modifying RNC Parameters in Batches)
to set RNC-oriented DRD algorithm parameters.
l Verification Procedure
Verifying this feature based on traffic steering
1. Configure cells A and B. Cell A provides R99 services, and cell B provides HSPA
services.
2. Enable the UE to establish an R99 service in cell A. Use the UE to download a large
file.
3. View the RRC_MEAS_CTRL message transmitted on the Uu interface. You can find
that this message contains inter-frequency measurement control information, as
shown in Figure 249-1.
Example
//Configuring this feature based on traffic steering
This section describes how to activate, verify, and deactivate the optional feature WRFD-020400
DRD Introduction Package.
Prerequisites
l Dependencies on Hardware
None
l Dependencies on Other Features
None
l License
This feature is not under license control.
Context
This feature supports DRD and redirection for users between inter-frequency/inter-RAT cells
covering the same area. DRD Introduction Package includes five features: WRFD-02040001
Intra System Direct Retry, WRFD-02040002 Inter System Direct Retry, WRFD-02040003 Inter
System Redirect, WRFD-02040004 Traffic Steering and Load Sharing During RAB Setup, and
Inter-frequency Redirection Based on Distance.
l Precautions
The following describes how to activate, verify, and deactivate inter-frequency redirection
based on distance. For details about how to activate, verify, and deactivate the other
features, see the corresponding feature activation guide.
251 Configuring Intra System Direct Retry
252 Configuring Inter System Direct Retry
253 Configuring Inter-System Redirect
254 Configuring Traffic Steering and Load Sharing During RAB Setup
l Data Preparation
Procedure
l Activating Inter-frequency Redirection Based on Distance
1. Run the BSC6900 MML command SET UDISTANCEREDIRECTION (CME
single configuration: UMTS Radio Global Configuration Express > Directed
Retry Parameter Configuration > RNC-Oriented Delay Based RRC Redirection
Parameters; CME batch modification center: 3.15 Modifying RNC Parameters in
Batches) for the RNC or ADD UCELLDISTANCEREDIRECTION (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell-
Oriented Delay Based RRC Redirection Parameters; CME batch modification
center: 3.18 Modifying UMTS Cell Parameters in Batches) for a cell. In this step,
turn on InterFreqRedirSwitch, set RedirBandInd based on the network plan, and
set other parameters according to the prepared data.
If RedirBandInd is set to DependOnNCell, you do not need to set
ReDirUARFCNUplinkInd, ReDirUARFCNDownlink, and
ReDirUARFCNUplink.
If RedirBandInd is set to other values, set ReDirUARFCNUplinkInd,
ReDirUARFCNDownlink, and ReDirUARFCNUplink based on the network
plan.
NOTE
Inter-frequency redirection based on distance does not select the inter-frequency neighboring
cell under the DRNC as the target cell. DRD and redirection at RRC connection setup do not
select the inter-frequency neighboring cell that uses a different frequency band from the cell
where the RRC connection is to access.
The distance between the UE and the NodeB must be larger than InterFreqRedirDelayThd
x 78.125 m/chip x 3 chips.
3. View the Uu interface tracing data.
If the RRC CONNECTION REJECT message includes the redirectionInfo IE
and this IE contains frequencyInfo (information about the cell), as shown in
Figure 250-1, the RNC has redirected the UE to an inter-frequency neighboring
cell and this feature has been activated.
If the RRC CONNECTION REJECT message does not include the
redirectionInfo IE, this feature has not been activated.
Example
//Activating Inter-frequency Redirection Based on Distance
SET UDISTANCEREDIRECTION: InterFreqRedirSwitch=ON,
InterFreqRedirDelayThd=10, InterFreqRedirFactorOfLDR=50,
InterFreqRedirFactorOfNorm=0, RedirBandInd=DependOnNCell;
ADD UCELLDISTANCEREDIRECTION: CellId=1, InterFreqRedirSwitch=ON,
InterFreqRedirDelayThd=10, InterFreqRedirFactorOfLDR=50,
InterFreqRedirFactorOfNorm=0, RedirBandInd=DependOnNCell;
This section describes how to activate, verify, and deactivate the optional feature
WRFD-02040001 Intra System Direct Retry.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
The feature WRFD-020400 DRD Introduction Package must be configured before this
feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature supports inter-RAT directed retries during RRC connection or radio resource bearer
(RAB) assignment.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, set Direct retry switch to
DR_RRC_DRD_SWITCH, DR_RAB_SING_DRD_SWITCH, and
DR_RAB_COMB_DRD_SWITCH.
2. Run the BSC6900 MML command SET UDRD (CME single configuration: UMTS
Radio Global Configuration Express > Directed Retry Parameter
Configuration > RNC-Oriented DRD Algorithm Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches). In this step, turn
on the RNC-level switches: Service Steering DRD Switch, Load balance DRD
switch for DCH, Load balance DRD switch for HSDPA, Code Balancing DRD
Switch, Uplink load balance DRD Switch for DC-HSDPA, Measurement-Based
DRD Switch, and Device Type Steering DRD Switch.
3. Optional: Run the BSC6900 MML command ADD UCELLDRD (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Oriented DRD Algorithm Parameters; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches). In this step, turn on the cell-level
switches: Service Steering DRD Switch, Load balance DRD switch for DCH, Load
balance DRD switch for HSDPA, Code Balancing DRD Switch, Uplink load
balance DRD Switch for DC-HSDPA, and Device Type Steering DRD Switch.
CAUTION
l If a cell is configured with both the RNC-level and cell-level parameters, the cell-
level parameter settings take effect. Therefore, do not modify the parameters to
default values when you are configuring the cell-level parameters.
l Intra system direct retry does not select the inter-frequency neighboring cell under
the DRNC as the target cell. DRD and redirection at RRC connection setup do not
select the inter-frequency neighboring cell that uses a different frequency band
from the cell where the RRC connection is to access.
l Verification Procedure
1. Method 1: Verifying this feature during RRC connection setup
a. Start Uu interface tracing on the BSC6900 LMT. Use a UE to initiate a PS
interactive service.
b. The UE sends an RRC_RRC_CONNECT_REQ message from cell 1 to the
BSC6900. The BSC6900 sends the UE an RRC_RRC_CONN_SETUP
message containing the scrambling code of cell 2.
c. The UE sends an RRC_RRC_CONNECT_SETUP_CMP message from cell
2 to the BSC6900. This indicates that this feature has been activated.
2. Method 2: Verifying this feature during radio bearer (RB) setup
a. Start Uu interface tracing on the BSC6900 LMT. Use a UE to initiate a PS
interactive service.
b. The BSC6900 sends an RRC_RB_SETUP message from cell 1 to the UE. The
UE sends an RRC_RB_SETUP_CMP message from cell 2 to the BSC6900. If
the service is set up successfully in cell 2 and the data transmission is normal,
this feature has been activated.
l Deactivation Procedure
1. Run the BSC6900 MML command SET UDRD (CME single configuration: UMTS
Radio Global Configuration Express > Directed Retry Parameter
Configuration > RNC-Oriented DRD Algorithm Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches) to turn off the
RNC-level switches.
2. Optional: Run the BSC6900 MML command MOD UCELLDRD (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Example
//Activating Intra System Direct Retry
SET UCORRMALGOSWITCH:
DrSwitch=DR_RRC_DRD_SWITCH-1&DR_RAB_SING_DRD_SWITCH-1&DR_RAB_COMB_DRD_SWI
TCH-1;
This section describes how to activate, verify, and deactivate the optional feature
WRFD-02040002 Inter System Direct Retry.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
The feature WRFD-020400 DRD Introduction Package must be configured before this
feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature supports inter-RAT directed retries during RAB assignment.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, set Direct retry switch to
DR_RAB_SING_DRD_SWITCH, DR_RAB_COMB_DRD_SWITCH, and
DR_INTER_RAT_DRD_SWITCH.
2. Run the BSC6900 MML command SET UDRD (CME single configuration: UMTS
Radio Global Configuration Express > Directed Retry Parameter
Configuration > RNC-Oriented DRD Algorithm Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches). In this step, set
the RNC-level parameter Max inter-RAT direct retry number to a value other than
zero, and turn on the following RNC-level switches: Service Steering DRD
Switch, Load balance DRD switch for DCH, Load balance DRD switch for
HSDPA, Code Balancing DRD Switch, Uplink load balance DRD Switch for DC-
HSDPA, Measurement-Based DRD Switch, and Device Type Steering DRD
Switch.
3. Optional: Run the BSC6900 MML command MOD UCELLDRD (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Oriented DRD Algorithm Parameters; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches). In this step, set the cell-level
parameter Max inter-RAT direct retry number to a value other than zero. Turn on
the following cell-level switches: Service Steering DRD Switch, Load balance DRD
switch for DCH, Load balance DRD switch for HSDPA, Code Balancing DRD
Switch, Uplink load balance DRD Switch for DC-HSDPA, and Device Type
Steering DRD Switch.
CAUTION
If a cell is configured with both the RNC-level and cell-level parameters, the cell-level
parameter settings take effect. Therefore, do not modify the parameters to default
values when you are configuring the cell-level parameters.
l Verification Procedure
1. Start Iu interface tracing on the BSC6900 LMT. Use a UE to initiate a PS interactive
service.
2. In the Iu Interface Trace dialog box, view the following procedure:
a. The core network (CN) sends a RAB_ASSIGNMENT_REQ message to the
BSC6900.
b. The BSC6900 responds to the CN with a RAB_ASSIGNMENT_RSP message
containing the cause value "direct retry."
c. The BSC6900 sends the CN a RELOCATION REQUIRED message
containing the cause value "direct retry."
l Deactivation Procedure
1. Run the BSC6900 MML command SET UDRD (CME single configuration: UMTS
Radio Global Configuration Express > Directed Retry Parameter
Configuration > RNC-Oriented DRD Algorithm Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches). In this step, set
Max Inter-RAT direct retry number to 0. Turn off the RNC-level switches.
2. Optional: Run the BSC6900 MML command MOD UCELLDRD (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Oriented DRD Algorithm Parameters; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches). In this step, set Max inter-RAT
direct retry number to 0. Turn off the cell-level switches.
----End
Example
//Activating Inter System Direct Retry
SET UCORRMALGOSWITCH:
DrSwitch=DR_RAB_SING_DRD_SWITCH-1&DR_RAB_COMB_DRD_SWITCH-1&DR_INTER_RAT_D
RD_SWITCH-1;
SET UDRD: DRMaxGSMNum=3, ServiceDiffDrdSwitch=ON, LdbDRDSwitchDCH=ON,
LdbDRDSwitchHSDPA=ON, CodeBalancingDrdSwitch=ON,
ULLdbDRDSwitchDcHSDPA=ON, BasedOnMeasHRetryDRDSwitch=ON, DPGDRDSwitch=ON;
ADD UCELLDRD: CellId=11, DRMaxGSMNum=3, ServiceDiffDrdSwitch=ON,
LdbDRDSwitchDCH=ON, LdbDRDSwitchHSDPA=ON, CodeBalancingDrdSwitch=ON,
ULLdbDRDSwitchDcHSDPA=ON, DPGDRDSwitch=ON;
//Deactivating Inter System Direct Retry
SET UDRD: DRMaxGSMNum=0, ServiceDiffDrdSwitch=OFF, LdbDRDSwitchDCH=OFF,
LdbDRDSwitchHSDPA=OFF, CodeBalancingDrdSwitch=OFF,
ULLdbDRDSwitchDcHSDPA=OFF, BasedOnMeasHRetryDRDSwitch=OFF,
DPGDRDSwitch=OFF;
MOD UCELLDRD: CellId=11, DRMaxGSMNum=0, ServiceDiffDrdSwitch=OFF,
LdbDRDSwitchDCH=OFF, LdbDRDSwitchHSDPA=OFF, CodeBalancingDrdSwitch=OFF,
ULLdbDRDSwitchDcHSDPA=OFF, DPGDRDSwitch=OFF;
This section describes how to activate, verify, and deactivate the optional feature
WRFD-02040003 Inter System Redirect.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
The feature WRFD-020400 DRD Introduction Package must be configured before this
feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature allows inter-system redirection during RRC connection setup.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, set Direct Retry Switch to
DR_RRC_DRD_SWITCH.
2. Run the BSC6900 MML command SET UDRD (CME single configuration: UMTS
Radio Global Configuration Express > Directed Retry Parameter
Configuration > RNC-Oriented DRD Algorithm Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches). In this step, set
ConnectFailRrcRedirSwitch to Allowed_To_Inter_RAT.
l Verification Procedure
Example
//Activating Inter-System Redirect
SET UCORRMALGOSWITCH: DrSwitch=DR_RRC_DRD_SWITCH-1;
SET UDRD: ConnectFailRrcRedirSwitch=Allowed_To_Inter_RAT;
//Deactivating Inter-System Redirect
SET UDRD: ConnectFailRrcRedirSwitch=OFF;
This section describes how to activate, verify, and deactivate the optional feature
WRFD-02040004 Traffic Steering and Load Sharing During RAB Setup.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
The feature WRFD-020400 DRD Introduction Package must be configured before this
feature is activated.
l License
This feature is not under license control.
Context
With this feature, service steering and load sharing among different frequencies or bands are
implemented during RAB setup based on the service type and cell load.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command ADD UINTERFREQNCELL (CME single
configuration: UMTS Cell Configuration Express > Neighboring Cell > Inter-
frequency Neighboring Cell; CME batch modification center: not supported). In this
step, add an inter-frequency cell by setting the related parameters according to the
network plan.
2. Run the BSC6900 MML command ADD USPG (CME single configuration: UMTS
Global Configuration Express > Radio Basic Data Configuration > Service
Priority Group; CME batch modification center: not supported). In this step, add a
service priority group and set the service priority of each type of service according to
the network plan.
3. Run the BSC6900 MML command MOD UCELL (CME single configuration:
UMTS Cell Configuration Express > Cell Basic Information > Cell Basic
Example
//Activating Service Steering and Load Sharing During RAB Setup
ADD UINTERFREQNCELL: RNCId=1, CellId=1, NCellRncId=1, NCellId=2,
SIB11Ind=TRUE, SIB12Ind=FALSE, TpenaltyHcsReselect=D0, BlindHoFlag=TRUE,
NPrioFlag=FALSE, DrdOrLdrFlag=TRUE, InterNCellQualReqFlag=FALSE;
This section describes how to activate, verify, and deactivate the optional feature WRFD-020402
Measurement Based Direct Retry.
Prerequisites
l Dependencies on Hardware
None
l Dependencies on Other Features
The feature WRFD-020400 DRD Introduction Package has been configured before this
feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
After a UE has successfully set up the RRC connection, the RNC instructs the UE to initiate
inter-frequency or inter-system measurements. Upon receipt of a radio access bearer (RAB)
assignment request from the CN, the RNC performs Directed Retry Decision (DRD) based on
the measurement results.
This feature increases the success rate of DRD and reduces the call drop rate caused by DRD
with blind handovers.
Procedure
l Activation Procedure
1. Run the BSC6900 MML commandADD UCELLMBDRINTERFREQ (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Oriented Inter-frequency Measurement Parameters for MBDR Algorithm; CME
batch modification center: 3.18 Modifying UMTS Cell Parameters in Batches). In
this step, set MBDR Switch, Inter-freq Measure Quantity, and other parameters
related to MBDR inter-frequency measurements.
When selecting the target cell after the MBDR algorithm is enabled, sort the candidate cells based
on Inter-freq Measure Quantity of MBDR (by running the ADD
UCELLMBDRINTERFREQ (CME single configuration: UMTS Cell Configuration Express >
Cell Parameters > Cell Oriented Inter-frequency Measurement Parameters for MBDR
Algorithm; CME batch modification center: 3.18 Modifying UMTS Cell Parameters in
Batches) command), and select a cell with the optimum signal quality as the target cell.
4. Run the BSC6900 MML commandADD UCELLMBDRINTERRAT (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Oriented Inter-RAT Measurement Parameters for MBDR Algorithm; CME
batch modification center: 3.18 Modifying UMTS Cell Parameters in Batches). In
this step, set MBDR switch in the parameters related to MBDR inter-RAT
measurements.
5. Run the BSC6900 MML commandADD UINTERFREQNCELL (CME single
configuration: UMTS Cell Configuration Express > Neighboring Cell > Inter-
frequency Neighboring Cell; CME batch modification center: not supported). In this
step, set Flag of MBDR Cell to TRUE(send), and set MBDR Cell Priority based
on the network plan.
l Verification Procedure
1. Congestion may occur when a large number of UEs access a cell. If a handover based
on inter-frequency measurements is used to achieve load reshuffling (LDR), you can
view the inter-frequency measurement control information on the Uu interface. After
a UE sends the inter-frequency measurement report, the UE will be handed over to
another cell.
l Deactivation Procedure
1. Run the BSC6900 MML commandMOD UCELLMBDRINTERFREQ (CME
single configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Oriented Inter-frequency Measurement Parameters for MBDR Algorithm; CME
batch modification center: 3.18 Modifying UMTS Cell Parameters in Batches) to
clear the MBDR Switch check box.
----End
Example
//Activating the feature Measurement-based Direct Retry
//Enabling the MBDR algorithm
ADD UCELLMBDRINTERFREQ: CellId=1,
InterFreqActiveType=CSAMR_INTERFREQ-1&CSNONAMR_INTERFREQ-1&PSR99_INTERFRE
Q-1&PSHSPA_INTERFREQ-1, InterFreqReportMode=EVENT_TRIGGER;
SET UNBMPARA: PerfEnhanceSwitch=PERFENH_MBDR_LOADCOND_OPT_SWITCH-1;
SET UCORRMPARA: PerfEnhanceSwitch=PERFENH_MBDR_TARCELLSEL_OPT_SWITCH-1;
//Setting the parameters related to cell-level MBDR inter-RAT
measurements
ADD UCELLMBDRINTERRAT: CellId=1, InterRatActiveType=CSAMR_INTERRAT-1;
//Setting the MBDR cell flag of the inter-frequency neighboring cell and
the MBDR cell priority
ADD UINTERFREQNCELL: RNCId=1, CellId=1, NCellRncId=2, NCellId=2,
SIB11Ind=TRUE, SIB12Ind=FALSE, TpenaltyHcsReselect=D0, BlindHoFlag=FALSE,
NPrioFlag=FALSE, MBDRFlag=TRUE, MBDRPrio=2, InterNCellQualReqFlag=FALSE;
//Deactivating the feature Measurement-based Direct Retry
//Disabling the MBDR algorithm
MOD UCELLMBDRINTERFREQ: CellId=1,
InterFreqActiveType=CSAMR_INTERFREQ-0&CSNONAMR_INTERFREQ-0&PSR99_INTERFRE
Q-0&PSHSPA_INTERFREQ-0;
This section describes how to activate, verify, and deactivate the optional feature WRFD-020120
Service Steering and Load Sharing in RRC Connection Setup.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
The feature WRFD-020400 DRD Introduction Package must be configured before this
feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others
The UE needs to be compliant with 3GPP Release 6 (or later) to support the feature.
Context
With this feature, service steering and load sharing among different frequencies, bands, or radio
access technologies (RATs) can be achieved during radio resource control (RRC) connection
setup based on the service type and cell load.
Procedure
l Activation Procedure
NOTE
The adaptive multirate (AMR) service that is redirected to an inter-RAT cell during RRC connection setup
is used as an example.
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to enable the RRC directed retry decision (DRD) function.
In this step, set Direct Retry Switch to DR_RRC_DRD_SWITCH.
2. Run the BSC6900 MML command SET UREDIRECTION (CME single
configuration: UMTS Radio Global Configuration Express > Directed Retry
Parameter Configuration > RNC-Oriented RRC Redirection Parameters; CME
batch modification center: 3.15 Modifying RNC Parameters in Batches). In this
step, set RNC-level Traffic Type to AMR and Redirection Switch to
ONLY_TO_INTER_RAT.
3. Optional: Run the BSC6900 MML command MOD UCELLREDIRECTION
(CME single configuration: UMTS Cell Configuration Express > Cell
Parameters > Cell-level RRC Redirection Parameters; CME batch modification
center: 3.18 Modifying UMTS Cell Parameters in Batches). In this step, set cell-
level Traffic Type to AMR and Redirection Switch to
ONLY_TO_INTER_RAT.
NOTE
If a cell is configured with both the RNC-level and cell-level parameters, the cell-level parameter
settings take effect.
l Verification Procedure
1. Use a UE to send an RRC_SETUP_REQ message with the cause value "Originating
Conversational Call."
2. The BSC6900 responds with an RRC_CONN_REJ message. If "redirectioninfo" of
the message contains "GSM-TargetCellInfo," this feature has been activated.
l Deactivation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to disable the RRC DRD function.
2. Run the BSC6900 MML command SET UREDIRECTION (CME single
configuration: UMTS Radio Global Configuration Express > Directed Retry
Parameter Configuration > RNC-Oriented RRC Redirection Parameters; CME
batch modification center: 3.15 Modifying RNC Parameters in Batches). In this
step, set Redirection Switch to an appropriate value to disable the RNC-level RRC
DRD based on service steering.
3. Optional: Run the BSC6900 MML command MOD UCELLREDIRECTION
(CME single configuration: UMTS Cell Configuration Express > Cell
Parameters > Cell-level RRC Redirection Parameters; CME batch modification
center: 3.18 Modifying UMTS Cell Parameters in Batches). In this step, set
Redirection Switch to an appropriate value to disable the cell-level RRC DRD based
on service steering.
----End
Example
/*Activating Service Steering and Load Sharing in RRC Connection Setup*/
This section describes how to activate, verify, and deactivate the optional feature WRFD-020124
Uplink Flow Control of User Plane.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
The Uplink Flow Control of User Plane feature is a Huawei proprietary feature. This feature
detects uplink packet loss for R99 services by using private information elements (IEs) on the
Iub interface. In addition, this feature controls uplink traffic by sending Transport Format
Combination Control messages. By doing this, this feature prevents uplink packet loss caused
by lack of flow control, and increases transmission efficiency.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET URRCTRLSWITCH (CME single
configuration: UMTS Radio Global Configuration Express > Process Switch
Configuration > Process Switch; CME batch modification center: 3.15 Modifying
RNC Parameters in Batches). In this step, set Process switch to
NODEB_PRIVATE_INTERFACE_SWITCH.
NOTE
NODEB_PRIVATE_INTERFACE_SWITCH controls all the functions that are achieved
by using the private messages on the Iub interface. Turn on other related switches if flow control
over the uplink user plane is required.
2. Run the NodeB MML command SET R99FLOWCTRLSWTCH (CME single
configuration: NodeB Configuration Express > IUB_NodeB > Radio Layer >
Locell Algorithm Parameters > Locell Parameters >
R99FLOWCTRLSWTCH; CME batch modification center: not supported) to turn
on the cell-level switch for uplink user plane flow control.
l Verification Procedure
1. Start an Iub interface tracing task on the BSC6900 LMT, as shown in Figure 257-1.
l Deactivation Procedure
1. Run the NodeB MML command SET R99FLOWCTRLSWTCH (CME single
configuration: NodeB Configuration Express > IUB_NodeB > Radio Layer >
Locell Algorithm Parameters > Locell Parameters >
R99FLOWCTRLSWTCH; CME batch modification center: not supported) to turn
off the cell-level switch for uplink user plane flow control.
----End
Example
//Activating Uplink Flow Control of User Plane
SET URRCTRLSWITCH: PROCESSSWITCH=NODEB_PRIVATE_INTERFACE_SWITCH-1;
SET R99FLOWCTRLSWTCH: SWITCH=OPEN, LOCELL=1;
//Deactivating Uplink Flow Control of User Plane
SET R99FLOWCTRLSWTCH: SWITCH=CLOSE, LOCELL=1;
This section describes how to activate, verify, and deactivate the optional feature WRFD-020104
Intra Frequency Load Balance.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature enables the change in cell load by adjusting the cell PCPICH power. For those UEs
in soft handover state, this feature enables the intra-frequency neighboring cells to share the cell
load by removing high load cell from the active set.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command ADD UINTRAFREQNCELL (CME single
configuration: UMTS Cell Configuration Express > Neighboring Cell > Intra-
frequency Neighboring Cell; CME batch modification center: not supported) to add
an intra-frequency neighboring cell.
2. Run the BSC6900 MML command MOD UCELLALGOSWITCH (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Algorithm Switches; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches). In this step, select INTRA_FREQUENCY_LDB(Intra
Frequency LDB Algorithm) from the Cell LDC algorithm switch drop-down list.
3. Run the BSC6900 MML command SET ULDCPERIOD (CME single configuration:
UMTS Radio Global Configuration Express > Load Control Parameter
Configuration > RNC Oriented LDC Algorithm Cycle Length; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches). In this step, set
Intra-frequency LDB period timer length to an appropriate value.
4. Run the BSC6900 MML command MOD UCELLLDB (CME single configuration:
UMTS Cell Configuration Express > Cell Parameters > Cell Oriented LDB
Algorithm Parameters; CME batch modification center: 3.18 Modifying UMTS
Cell Parameters in Batches) to set the following parameters associated with the cell-
level intra-frequency load balancing (LDB) algorithm to appropriate values:
Cell overload threshold
Pilot power adjustment step
Cell under load threshold
5. Run the BSC6900 MML command MOD UPCPICHPWR (CME single
configuration: UMTS Cell Configuration Express > Channel Configuration >
PCPICH; CME batch modification center: 3.20 Modifying UMTS Channel
Parameters in Batches). In this step, set P-CPICH parameters associated with intra-
frequency LDB, including Max transmit power of PCPICH and Min transmit
power of PCPICH to appropriate values.
l Verification Procedure
To verify that the RNC can balance the cell load by adjusting the P-CPICH power of a cell,
perform the following steps:
1. On the BSC6900 LMT, open the Monitor tab page. Create the task of monitoring
PCPICH TxPower of CELL_A11.
2. Run the NodeB MML command STR DLSIM to simulate high load in CELL_A11.
3. In the Cell Performance Monitoring dialog box, check the pilot power of
CELL_A11.
Expected result: As the cell load increases, the pilot power periodically decreases. The
actual pilot power must not be decreased to a level lower than the configured minimum
pilot power.
4. The NBAP_CELL_RECFG_REQ and NBAP_CELL_RECFG_RSP messages
should be displayed in the Iub tracing result. In the NBAP_CELL_RECFG_REQ
message, check whether the RNC has reduced the pilot power.
5. Run the NodeB MML command STR DLSIM to stop simulating high load in
CELL_A11.
6. In the Cell Performance Monitoring dialog box, check the pilot power of
CELL_A11.
Expected result: As the cell load becomes normal, the pilot power periodically
increases. The actual pilot power must not be increased to a level higher than the
configured maximum pilot power.
l Deactivation Procedure
1. Run the BSC6900 MML command MOD UCELLALGOSWITCH (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Algorithm Switches; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches). In this step, deselect INTRA_FREQUENCY_LDB from
the Cell LDC algorithm switch drop-down list.
2. Restore the parameter settings modified in the activation procedure.
----End
Example
//Activating Intra Frequency Load Balance
//Configuring intra-frequency neighboring cells
ADD UINTRAFREQNCELL: RncId=1, CellId=111, NCellRncId=1, NCellId=211,
SIB11Ind=TRUE, SIB12Ind=FALSE, TpenaltyHcsReselect=D0, NPrioFlag=FALSE;
//Enabling the cell-oriented intra-frequency LDB algorithm
MOD UCELLALGOSWITCH: CellId=111, NBMLdcAlgoSwitch=INTRA_FREQUENCY_LDB-1;
//Setting the intra-frequency LDB period
SET ULDCPERIOD: IntraFreqLdbPeriodTimerLen=1800;
//Setting parameters associated with the cell-oriented intra-frequency
LDB algorithm to appropriate values
MOD UCELLLDB: CellId=111, PCPICHPowerPace=2, CellOverrunThd=90,
CellUnderrunThd=30;
//Setting the P-CPICH associated parameters for intra-frequency LDB
MOD UPCPICHPWR: CellId=111, MaxPCPICHPower=346, MinPCPICHPower=313;
//Verifying Intra Frequency Load Balance
STR DLSIM: LOCELL=111, LR=90;
STP DLSIM: LOCELL=111;
//Deactivating Intra Frequency Load Balance
MOD UCELLALGOSWITCH: CellId=111, NBMLdcAlgoSwitch=INTRA_FREQUENCY_LDB-0;
This section describes how to activate, verify, and deactivate the optional feature WRFD-140211
Dynamic Target RoT Adjustment.
Prerequisites
l Dependencies on Hardware
The BTS3812E, BTS3812A, or BTS3812AE must be configured with the EBBI, EBOI,
EULP+EDLP, or EULPd+EDLP boards. Downlink cells must be set up on the EBBI,
EBOI, or EDLP board.
The DBS3800 must be configured with the EBBC or EBBCd board, and downlink cells
must be set up on the EBBC or EBBCd board.
The 3900 series base stations must be configured with the WBBPb, WBBPd, or WBBPf
board. Downlink cells must be set up on the WBBPb, WBBPd, or WBBPf board.
l Dependencies on Other Features
Configurations of other features on which this feature depends are complete. This
feature depends on feature WRFD-010612 HSUPA Introduction Package.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others
This feature should be used with professional services.
Context
l Precautions
None
l Data Preparation
Procedure
l Activation Procedure
1. Run the BSC6900 MML commandADD UCELLLICENSE (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
License Resource/Function Item; CME batch modification center: 3.18 Modifying
UMTS Cell Parameters in Batches). In this step, select
DYN_TGTROT_CTRL_SWITCH(Dynamic Target RoT Adjustment) under
Function Switch1 to enable the license of dynamic target ROT adjustment for a
specified cell.
2. Run the BSC6900 MML command MML command ADD UCELLHSUPA (CME
single configuration: UMTS Cell Configuration Express > Cell Parameters >
Configuration of HSUPA in Cell; CME batch modification center: 3.18 Modifying
UMTS Cell Parameters in Batches) or MOD UCELLHSUPA (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters >
Configuration of HSUPA in Cell; CME batch modification center: 3.18 Modifying
UMTS Cell Parameters in Batches) to enable Dynamic Target RoT Adjustment. In
this step, set Switch for Dynamically Adjusting RoT to ON(ON).
l Verification Procedure
Check the related performance counters on the M2000.
1. On the M2000, check the counter VS.HSUPA.TgtRoTInc or
VS.HSUPA.TgtRoTDec. If the value of either counter is not 0, this feature has
been activated.
Initiate message tracing on the LMT.
1. On the Run the BSC6900 MML command LMT, click Trace and display the
Iub Interface Trace dialog box. On the Basic tab page, select the NBAP check
box under the Trace Type parameter. On the NBAP tab page, select the
NBAP_COMM_MEAS_RPRT check box under the Message Type parameter.
Then, click Submit to enter the Iub interface trace page.
2. On the Iub interface trace page, check Message Type. If
NBAP_COMM_MEAS_RPRT is displayed and the measurement type is uL-
Timeslot ISCP, this feature has been activated, as shown in Figure 259-1.
l Deactivation Procedure
1. Run the Run the BSC6900 MML command MML command MOD
UCELLHSUPA (CME single configuration: UMTS Cell Configuration Express >
Cell Parameters > Configuration of HSUPA in Cell; CME batch modification
center: 3.18 Modifying UMTS Cell Parameters in Batches) to disable Dynamic
Target RoT Adjustment. In this step, set Switch for Dynamically Adjusting RoT to
OFF(OFF).
----End
Example
//Activating Dynamic Target RoT Adjustment
ADD UCELLLICENSE: CellId=1, FuncSwitch1=DYN_TGTROT_CTRL_SWITCH-1;
ADD UCELLHSUPA: CellId=1, DynTgtRoTCtrlSwitch=ON;
//Deactivating Dynamic Target RoT Adjustment
MOD UCELLHSUPA: CellId=1, DynTgtRoTCtrlSwitch= OFF;
This section describes how to activate, verify, and deactivate the optional feature WRFD-140212
CE Overbooking.
Prerequisites
l Dependencies on Hardware
This feature has the following impact on the NodeB hardware:
The 3900 series base station must be configured with the WBBPb, WBBPd, or
WBBPf board.
The DBS3800 must be configured with the EBBC or EBBCd board.
The BTS3812E, BTS3812A, and BTS3812AE must be configured with the EBBI,
EBOI, or EULPd board.
l Dependencies on Other Features
Configurations of other features on which this feature depends are complete. This
feature depends on features WRFD-010638 Dynamic CE Resource Management.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others
This feature should be used with Huawei professional services.
Procedure
l Activation Procedure
1. After the license is activated, this feature has been activated.
2. Run the BSC6900 MML command SET UALGORSVPARA (CME single
configuration: UMTS Global Configuration Express > Reserved Parameters >
System Level Reserved Parameters; CME batch modification center: 3.15
Modifying RNC Parameters in Batches). In this step, set Reserved Switch 1 to
RESERVED_SWITCH_1_BIT5.
NOTE
The NodeB baseband board uses different processing specifications for users with different
uplink bearer services, for example, HSUPA TTI 2 ms service,s HSUPA TTI 10 ms services,
and R99 services. When multiple users access the network,
l If this function is disabled, the system attempts to admit all new users using the highest
service bearers supported by the terminal. In this way, accessed users occupy too many
uplink processing specifications and therefore the total number of accessed users decreases.
l If this function is enabled, the NodeB baseband board dynamically selects proper uplink
service bearers for users to maximize the number of accessed users according to actual
NodeB processing specifications.
l Verification Procedure
Verify that the value of the new counter VS.NodeB.ULCreditUsed.Mean,
VS.NodeB.ULCreditUsed.Max or VS.NodeB.ULCreditUsed.Min is not 0. A non-zero
value indicates that CE Overbooking takes effect.
l Deactivation Procedure
None
----End
Example
//Activation Procedure SET
UALGORSVPARA:RsvSwitch1=RESERVED_SWITCH_1_BIT5-1;
This section describes how to activate, verify, and deactivate the optional feature WRFD-140213
Intelligent Access Class Control.
Prerequisites
l Dependencies on Hardware
This feature does not depend on Hardware.
l Dependencies on other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others
UEs must support access class control delivered in system information.
For UEs complying with 3GPP Release 5 and earlier releases, access class control
cannot be performed on CS and PS services separately. If the access class of such a UE
is barred, the UE can process neither CS nor PS services.
For UEs complying with 3GPP Release 6 and later releases, access class control can be
performed on CS and PS services separately. Therefore, such a UE can process CS
services while being barred from processing PS services.
Context
This feature prevents a large number of UEs from sending RRC connection setup requests
simultaneously. When the RNC determines that a cell is congested, the RNC restricts the access
of UEs of more access classes. When the RNC determines that congestion is relieved in the cell,
the RNC reduces the number of access classes on which access control is performed. This
prevents excessive RRC connection setup requests from wasting Uu interface resources and
RNC processing resources, relieves network congestion, and improves system stability.
l Precautions
None.
l Data Preparation
Paramet Parame Parameter Setting Data Source
er Name ter ID
Consideri CongOf Turn on this switch only when you Network plan
ng UL UlLoadS want to take the uplink power load
Load in witch congestion as a necessary condition for
Cell Cong increasing the number of barred ACs.
Decision
Consideri CongOf Turn on this switch only when you Network plan
ng CPU CpuSwit want to take the SPU CPU usage as a
Usage in ch necessary condition for increasing the
Cell Cong number of barred ACs.
Decision
Max No. RstrctR6 The default value is recommended for Network plan
of PS PSMax this parameter.
Restricte ACNum
d AC for
R6 or
Later
Max No. RstrctR5 The default value is recommended for Network plan
of MaxAC this parameter.
Restricte Num
d Access
Class for
R5 or
Early
Max No. RstrctR6 The default value is recommended for Network plan
of PS CSMax this parameter.
Restricte ACNum
d AC for
R6 or
Later
Procedure
l Activation Procedure
Run the BSC6900 MML command ADD UCELLCONGACALGO (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell Control
Parameters for Intelligent Access; CME batch modification center: 3.18 Modifying
UMTS Cell Parameters in Batches). In this step, perform the following steps:
1. Set CongACSwitch to ON.
2. Set ACRstrctRange to an appropriate value.
3. Optional: Perform the following operations based on the network plan:
If the radio access bearer (RAB) rejection rate needs to be considered during a
congestion decision, set CongOfRABRejRateSwitch to ON, and set
CongRejTrigThd and CongRejRelThd based on site requirements.
Example
//Activating Intelligent Access Class Control for cell1 where the access
class ranges from AC0 to AC9
ADD UCELLCONGACALGO: CellId=1, CongACSwitch=ON,
ACRstrctRange=AC0-1&AC1-1&AC2-1&AC3-1&AC4-1&AC5-1&AC6-1&AC7-1&AC8-1&AC9-1
;
//Deactivating Intelligent Access Class Control for cell1
MOD UCELLCONGACALGO: CellId=1, CongACSwitch=OFF;
This section describes how to activate, verify, and deactivate the optional feature WRFD-140215
Dynamic Configuration of HSDPA CQI Feedback Period.
Prerequisites
l Dependencies on Hardware
To implement dynamic configuration of CQI feedback period based on the uplink load,
the NodeB needs to reports actual service load. The reported value has the following
requirements for the NodeB configuration:
The BTS3812E, BTS3812A and BTS3812AE do not support this feature.
The DBS3800 does not support this feature.
If the 3900 series base station is configured with the WBBPa board or the RRU3801C
20 W, this feature is not supported. In other configurations, this feature is supported.
To implement dynamic configuration of CQI feedback period based on CS+PS services
or based on limited coverage, the NodeB does not require any dependency.
l Dependencies on Other Features
Configurations of other features on which this feature depends are complete. This
feature depends on feature WRFD-010610 HSDPA Introduction Package.
This feature is not supported when WRFD-021350 Independent Demodulation of
Signals from Multiple RRUs in One Cell is enabled.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Dependencies on Others
This feature needs UE to suport HSDPA.
Context
This feature considers the uplink load as the criterion for dynamically adjusting the channel
quality indicator (CQI) feedback period for HSDPA UEs. The goal is to ensure high downlink
rates when only a small number of HSDPA UEs are online and to increase the uplink capacity
when a large number of HSDPA UEs are online. For HSUPA UEs at cell edges or UEs engaged
in CS/PS combined services, a longer CQI feedback period reduces the call drop rate and
improves user experience.
l Precautions
None
l Data Preparation
Parameter Name Parameter ID Setting Source
Description
Procedure
l Activation Procedure
1. Run the BSC6900 MML commandADD UCELLLICENSE (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
License Resource/Function Item; CME batch modification center: 3.18 Modifying
UMTS Cell Parameters in Batches) or MOD UCELLLICENSE (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
License Resource/Function Item; CME batch modification center: 3.18 Modifying
UMTS Cell Parameters in Batches). In this step, select DYN_CQI_ADJUST under
Function Switch1 to enable the license of dynamic configuration of HSDPA CQI
feedback period for a specified cell.
2. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches), with the following parameter settings:
To enable the load-based algorithm for periodically selecting the CQI feedback
period, select PC_CQI_CYCLE_BASE_CELLLOAD_SWITCH under the
Power Control Switch parameter.
To enable the coverage-based algorithm for periodically selecting the CQI
feedback period, select PC_CQI_CYCLE_BASE_COVERAGE_SWITCH
under the Power Control Switch parameter.
To enable the algorithm based on CS/PS combined services for periodically
selecting the CQI feedback period, select
PC_CQI_CYCLE_BASE_CS_PLUS_PS_SWITCH under the Power Control
Switch parameter.
3. When enabling the coverage-based algorithm for periodically selecting the CQI
feedback period, you need to run the BSC6900 MML command SET
UCORRMALGOSWITCH (CME single configuration: UMTS Radio Global
Configuration Express > Connection_Oriented RRM Switch Configuration >
Connection Oriented Algorithm Switches; CME batch modification center: 3.15
Modifying RNC Parameters in Batches), with RESERVED_SWITCH_0_BIT5
or RESERVED_SWITCH_0_BIT7 selected under the CORRM Algorithm
Reserved Switch 0 parameter to enable the algorithm for shifting BE services from
HSUPA to R99 in the case of weak coverage or the coverage-based algorithm for BE
services on E-DCHs to fall back to DCHs.
NOTE
The coverage-based algorithm for periodically selecting the CQI feedback period depends on the
algorithm for shifting BE services from HSUPA to R99 in the case of weak coverage or the coverage-
based algorithm for BE services on E-DCHs to fall back to DCHs. That is, enable at least one of the
two algorithms before enabling the coverage-based algorithm for periodically selecting the CQI
feedback period.
4. Optional: Run the BSC6900 MML command SET UHSDPCCH (CME single
configuration: UMTS Radio Global Configuration Express > HS-DPCCH Power
Control Configuration > RNC-Oriented HS-DPCCH Power Control Algorithm
Parameters; CME batch modification center: 3.15 Modifying RNC Parameters in
Batches) (RNC level), ADD UCELLHSDPCCH (CME single configuration: UMTS
Cell Configuration Express > Cell Parameters > Cell-Oriented HS-DPCCH
Power Control Algorithm Parameters; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches) (cell level), or MOD
UCELLHSDPCCH (CME single configuration: UMTS Cell Configuration
Example
//Activating Dynamic Configuration of HSDPA CQI Feedback Period
ADD UCELLLICENSE: CellId=1, FuncSwitch1=DYN_CQI_ADJUST-1;
SET UCORRMALGOSWITCH:
PcSwitch=PC_CQI_CYCLE_BASE_CELLLOAD_SWITCH-1&PC_CQI_CYCLE_BASE_COVERAGE_S
WITCH-1&PC_CQI_CYCLE_BASE_CS_PLUS_PS_SWITCH-1;
This section describes how to activate, verify, and deactivate the optional feature WRFD-140216
Load-based Uplink Target BLER Configuration.
Prerequisites
l Dependencies on Hardware
This features requires the NodeB to report the value of the uplink actual service load.
The reported value has the following requirements for the NodeB configuration:
The BTS3812E, BTS3812A and BTS3812AE do not support this feature.
The DBS3800 does not support this feature.
If the 3900 series base station is configured with the WBBPa board or the RRU3801C
20W, this feature is not supported. In other configurations, this feature is supported.
l Dependencies on Other Features
This feature is not supported when WRFD-021350 Independent Demodulation of
Signals from Multiple RRUs in One Cell is enabled.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature is designed for UEs whose services carried by DCHs are all BE services. When the
uplink load on the cell causes congestion, this feature configures a large target BLER. This
mechanism lowers the uplink load on the cell, increases the cell capacity, and reduces the
possibility of call drops for cell edge users (CEUs).
l Precautions
None
l Data Preparation
Procedure
l Activation Procedure
1. Run the BSC6900 MML command ADD UCELLLICENSE (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
License Resource/Function Item; CME batch modification center: 3.18 Modifying
UMTS Cell Parameters in Batches) or MOD UCELLLICENSE (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
License Resource/Function Item; CME batch modification center: 3.18 Modifying
UMTS Cell Parameters in Batches). In this step, select DYN_BLER_PS under
Function Switch1,to enable the license of load-based uplink target BLER
configuration for a specified cell.
2. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches), with
PC_BLER_TARGET_BASE_CELLLOAD_SWITCH under Power Control
Switch selected. This operation enables the load-based algorithm for selecting the
target BLER.
3. Optional: Run the BSC6900 MML command SET UOLPC (CME single
configuration: UMTS radio global Configuration Express > RNC-Oriented
OLPC Algorithm Parameters Configuration > RNC-Oriented OLPC Algorithm
Parameters; CME batch modification center: 3.15 Modifying RNC Parameters in
Batches), with Uplink Target BLER for Heavily Loaded Cells set to a large value.
4. Optional: Run the BSC6900 MML commandADD UCELLLDM (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Oriented LDM Algorithm Parameters; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches) to set the value of UL Actual Load
Trigger Threshold.
5. Optional: To maximize the gain of the feature Load-based Uplink Target BLER
Configuration, it is recommended that you activate the optimized outer loop power
control. For details, see "Activating optimized outer loop power control" in 22
Configuring Outer Loop Power Control.
l Verification Procedure
Check the value of the counter VS.ULBler.BE.Large, which indicates the number of
attempts to set the target BLER when the uplink load on the cell causes congestion. If the
value of this counter is not 0, this feature has been activated.
l Deactivation Procedure
1. Run the BSC6900 MML command MOD UCELLLICENSE (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
License Resource/Function Item; CME batch modification center: 3.18 Modifying
UMTS Cell Parameters in Batches). In this step, clear DYN_BLER_PS(Load-
based Uplink Target BLER Configuration) under Function Switch1, to disable the
license of dynamic configuration of load-based uplink target BLER configuration for
a specified cell.
2. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches), with
PC_BLER_TARGET_BASE_CELLLOAD_SWITCH under Power Control
Switch cleared. This operation disables the load-based algorithm for selecting the
target BLER.
----End
Example
This section describes how to activate, verify, and deactivate the optional feature WRFD-140217
Inter-Frequency Load Balancing Based on Configurable Load Threshold.
Prerequisites
l Dependencies on Hardware
This feature does not depend on Hardware.
l Dependencies on Other Features
This feature depends on the feature WRFD-020110 Multi Frequency Band Networking
Management in the inter-band networking scenario.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature balances the load among inter-frequency cells by triggering measurement-based
inter-frequency handovers. With this feature, the RNC compares measurement results of uplink
and downlink power resource, code resource, and channel element (CE) resource in a cell with
load thresholds for the corresponding services. Based on the comparison result, the RNC selects
the UEs and target cell for an inter-frequency handover. This feature supports load balancing
between cells on the following frequencies.
l Intra-band frequencies
l Inter-band frequencies
l Inter-RNC frequencies
l Inter-vendor frequencies
l Frequencies between the macro network and the micro network
l Precautions
None
l Data Preparation
Parameter Name Parameter ID Setting Source
Description
Procedure
l Activation Procedure
1. Run the BSC6900 MML commandADD UCELLLICENSE (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
License Resource/Function Item; CME batch modification center: 3.18 Modifying
UMTS Cell Parameters in Batches) or MOD UCELLLICENSE (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
License Resource/Function Item; CME batch modification center: 3.18 Modifying
UMTS Cell Parameters in Batches). In this step, under FuncSwitch1, select
INTER_FREQ_LOAD_BALANCE_BASEON_CFG_THD(Inter-Frequency
Load Balancing Based on Config Load Thd) to enable the license of CLB for a
specified cell.
2. Run the BSC6900 MML commandADD UCELLALGOSWITCH (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Algorithm Switches; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches) or MOD UCELLALGOSWITCH (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Algorithm Switches; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches). In this step, under NBMLdcAlgoSwitch, select
UL_UU_CLB to enable uplink Uu-interface load balancing, select DL_UU_CLB to
enable downlink Uu-interface load balancing, select CELL_CODE_CLB to enable
cell code resource load balancing, and select CELL_CREDIT_CLB to enable cell
credit load balancing for a specified cell.
3. Run the BSC6900 MML commandADD UNODEBALGOPARA (CME single
configuration: NodeB Configuration Express > IUB_RNC > NodeB Basic
Information > NodeB Algorithm Parameters; CME batch modification center: 3.16
Modifying Logical NodeB Parameters in Batches) or MOD
UNODEBALGOPARA (CME single configuration: NodeB Configuration
Express > IUB_RNC > NodeB Basic Information > NodeB Algorithm
Parameters; CME batch modification center: 3.16 Modifying Logical NodeB
Parameters in Batches). In this step, under NodeBLdcAlgoSwitch, select
NODEB_CREDIT_CLB_SWITCH(NodeB Credit CLB Algorithm) to enable
NodeB credit load balancing and select LCG_CREDIT_CLB_SWITCH(Local Cell
Group Credit CLB Algorithm) to enable local cell group credit load balancing for
a specified NodeB.
4. Run the BSC6900 MML commandADD UINTERFREQNCELL (CME single
configuration: UMTS Cell Configuration Express > Neighboring Cell > Inter-
frequency Neighboring Cell; CME batch modification center: not supported) or
MOD UINTERFREQNCELL (CME single configuration: UMTS Cell
Configuration Express > Neighboring Cell > Inter-frequency Neighboring Cell;
CME batch modification center: not supported). In this step, set CLBFlag for the
inter-frequency neighboring cell of a specified cell to TRUE, and set CLBPrio based
on the network plan.
NOTE
The inter-frequency neighboring cell of intra-RNC whose CLBFlag is TRUE can be the target
cell of an inter-frequency handover using CLB only after step 1 is performed.
5. Run the BSC6900 MML command ADD UCELLCLB (CME single configuration:
UMTS Cell Configuration Express > Cell Parameters > Cell-Oriented
Parameters for CLB interfreq Load Banlance Algorithm; CME batch
modification center: 3.18 Modifying UMTS Cell Parameters in Batches) or MOD
UCELLCLB (CME single configuration: UMTS Cell Configuration Express >
Cell Parameters > Cell-Oriented Parameters for CLB interfreq Load Banlance
Algorithm; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches). In this step, set the feature parameters for a specified cell.
Based on the site requirements, set CellLoadBalanceRange to
ONLY_TO_INTRA_RNC, ONLY_TO_INTER_RNC, or
BOTH_TO_INTRA_RNC_AND_INTER_RNC to enable intra-RNC inter-
frequency load balancing, inter-RNC inter-frequency load balancing, or intra- and
inter-RNC inter-frequency load balancing, respectively. Keep the default settings of
other parameters, which are the thresholds for inter-frequency load balancing because
of code resource, cell credit resource, and MaxUserNumforCLBIFHO.
6. Optional: If CellLoadBalanceRange in step 5 is set to ONLY_TO_INTER_RNC
or BOTH_TO_INTRA_RNC_AND_INTER_RNC, Run the BSC6900 MML
commandSET UCLB (CME single configuration: UMTS Radio Global
Configuration Express > Load Control Parameter Configuration > RNC
Parameters for CLB interfreq Load Banlance Algorithm; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches) to set the
parameters related to the cell load status of the neighboring RNC.
7. Optional: Run the BSC6900 MML commandSET ULDCPERIOD (CME single
configuration: UMTS Radio Global Configuration Express > Load Control
Parameter Configuration > RNC Oriented LDC Algorithm Cycle Length; CME
batch modification center: 3.15 Modifying RNC Parameters in Batches). In this
step, set ClbPeriodTimerLen.
8. Optional: If NODEB_CREDIT_CLB_SWITCH(NodeB Credit CLB
Algorithm) or LCG_CREDIT_CLB_SWITCH(Local Cell Group Credit CLB
Algorithm)is selected under NodeBLdcAlgoSwitch in step 3, Run the BSC6900
MML commandADD UNODEBCLB (CME single configuration: NodeB
Configuration Express > IUB_RNC > NodeB Basic Information > NodeB-
Oriented Parameters for CLB interfreq Load Banlance Algorithm; CME batch
modification center: 3.16 Modifying Logical NodeB Parameters in Batches) or
MOD UNODEBCLB (CME single configuration: NodeB Configuration Express
> IUB_RNC > NodeB Basic Information > NodeB-Oriented Parameters for CLB
interfreq Load Banlance Algorithm; CME batch modification center: 3.16
Modifying Logical NodeB Parameters in Batches). In this step, set the feature
parameters for a specified NodeB. Keep the default parameter settings, which are the
thresholds for inter-frequency load balancing because of cell group credit resource
and NodeB credit resource.
9. Optional: If UL_UU_CLB or DL_UU_CLB is selected under
NBMLdcAlgoSwitch in step 2, Run the BSC6900 MML commandADD
UCELLLDM (CME single configuration: UMTS Cell Configuration Express >
Cell Parameters > Cell Oriented LDM Algorithm Parameters; CME batch
modification center: 3.18 Modifying UMTS Cell Parameters in Batches) or MOD
Example
/*Activating the feature WRFD-140217 Inter-Frequency Load Balancing Based on
Configurable Load Threshold*/
//Disabling NodeB credit load balancing and local cell group credit load
balancing for a specified NodeB
MOD UNODEBALGOPARA: IDTYPE=BYID, NodeBId=1,
NodeBLdcAlgoSwitch=NODEB_CREDIT_CLB_SWITCH-0&LCG_CREDIT_CLB_SWITCH-0;
This section describes how to activate, verify, and deactivate the optional feature WRFD-070004
Load Based GSM and UMTS Handover Enhancement Based on Iur-g.
Prerequisites
l Dependencies on Hardware
The BSC model is the BSC6900.
A GSM+UMTS dual-mode MS is required.
Interface board FG2a/FG2c/GOUa/GOUc should be configured to support Iur-g.
l Dependencies on Other Features
Configurations of other features on which this feature depends are complete. This
feature depends on features GBFD-511101 Load Based Handover Enhancement on Iur-
g, WRFD-020306 Inter-RAT Handover Based on Load or WRFD-021200 HCS
(Hierarchical Cell Structure).
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others
Both the 2G network and the 3G network are deployed.
IP transmission mode is used on the Iur-g interface.
A GSM cell and a UMTS cell are configured and the GSM cell is configured as the
neighboring cell of the UMTS cell.
Data is negotiated and planned for the inter-BSC6900 Iur-g interface. For details you
can refer to Configuring the inter-BSC6900 Iur-g interface.
NOTE
l The licenses on the BSC and the RNC sides are activated separately.
Context
This feature is based on Huawei private information exchange mechanism over the Iur-g
interface. With this feature, the traffic is distributed through the RRC redirection and load-based
handover from the 3G network to the 2G network on the basis of the service attributes and the
load of the 2G networks when 3G cell enters LDR status. In this manner, the load is shared by
the GSM network when the load of UMTS network is heavy.
Procedure
l Activation Procedure
1. Configuration on the RNC side
a. Run the BSC6900 MML command SET UMBSCCRRM (CME single
configuration: UMTS Radio Global Configuration Express > MBMS
Configuration > MBSC Comm-RRM Algorithm Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches) to enable
the non-coverage-based handover. In this step, set Non-Coverage Handover
Based on 2G Load Indication to ON(ON), Adjustment Coefficient of 2G
Load Value to 1 and Load-base Handover Based on 3G2G Load Difference
Indication to ON(ON).
b. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME
single configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to enable the inter-RAT handover. In this step, select
HO_INTER_RAT_CS_OUT_SWITCH and
HO_INTER_RAT_PS_OUT_SWITCH in the HandOver switch drop-down
list box.
c. Run the BSC6900 MML command MOD UCELLALGOSWITCH (CME
single configuration: UMTS Cell Configuration Express > Cell Parameters
> Cell Algorithm Switches; CME batch modification center: 3.18 Modifying
UMTS Cell Parameters in Batches) to enable UL and DL load reshuffling
(LDR) on the Uu interface. In this step, select UL_UU_LDR(Uplink UU LDR
Algorithm) and DL_UU_LDR(Downlink UU LDR Algorithm) in the Switch
for Cell Load Control drop-down list box.
d. Run the BSC6900 MML command MOD UCELLLDR (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
LDR Algorithm Parameters; CME batch modification center: 3.18 Modifying
UMTS Cell Parameters in Batches) to configure LDR actions. In this step, set
DL LDR first action and UL LDR first action to CSInterRatShouldBeLDHO
(CS domain inter-rat should be load handover); set DL LDR second action
and UL LDR second action to PSInterRatShouldBeLDHO(PS domain inter-
rat should be load handover); set DL LDR third action and UL LDR third
action to CSInterRatShouldNotLDHO(CS domain inter-rat should not be
load handover); set DL LDR fourth action and UL LDR fourth action to
PSInterRatShouldNotLDHO(PS domain inter-rat should not be load
handover).
NOTE
You need to configure UL and DL LDR actions according to the actual situation.
2. Configuration on the BSC side
a. Run the BSC6900 MML command SET GCELLHOINTERRATLDB (CME
single configuration: Cell Configuration Express > Handover Data > Inter-
RAT Handover Parameters; CME batch modification center: Modifying GSM
Cell Parameters in Batches) to activate MBSC Handover based on Load
Enhancement on the GSM side. In this step, set Allow Inter-RAT Load HO in
Connect State to YES(Yes).
b. Run the BSC6900 MML command SET GCELLHOBASIC (CME single
configuration: Cell Configuration Express > Handover Data > Basic
Handover Parameters of Cell; CME batch modification center: Modifying
GSM Cell Parameters in Batches) to enable inter-RAT handovers. In this step,
set Inter-RAT Out BSC Handover Enable and Inter-RAT In BSC Handover
Enable to YES(Yes) .
c. Run the BSC6900 MML command SET GCELLHOINTERRATLDB (CME
single configuration: Cell Configuration Express > Handover Data > Inter-
RAT Handover Parameters; CME batch modification center: Modifying GSM
Cell Parameters in Batches) to set 2G Load Adjustment Coefficient. Setting 2G
Load Adjustment Coefficient to 10 is recommended.
l Verification Procedure
NOTE
l If the verification achieves the following results as expected, the configuration succeeds. Otherwise,
the configuration fails.
1. 3G-to-2G Load Based Handover Enhancement
CAUTION
The verification can be done when only the UMTS cell is in the basic congestion state.
a. Use the dual-mode MS to call a fixed telephone in the UMTS cell. Trace signaling
on the Iu interface on the LMT. RANAP_RELOCATION_REQUIRED
message is reported. The RANAP_RELOCATION_REQUIRED message
contains reduce-load-in-serving-cell. Trace signaling on the A interface on the
LMT. Handover Request message is reported. The Handover Request
message contains reduce-load-in-serving-cell.
NOTE
After the verification, set the value of system to the value before the verification.
2. 2G-to-3G Load Based Handover Enhancement
a. Use the MS to initiate a call in the GSM cell, and the call is successfully
established.
b. When the GSM cell is in the basic congestion state, the MS hand over to 3G
neighbor cell. Trace signaling on the A interface. Check that Assignment
Request, Handover Required, and Handover Command messages are
reported and cause in the Handover Required message is reduce-load-in-
serving-cell.
l Deactivation Procedure
1. Configuration on the RNC side
Run the BSC6900 MML command SET UMBSCCRRM (CME single
configuration: UMTS Radio Global Configuration Express > MBMS
Configuration > MBSC Comm-RRM Algorithm Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches) to deactivate
MBSC Handover based on Load Enhancement on the UMTS side. In this step, set
Example
//Activating Handover based on Load Enhancement
//Configuration on the RNC side
/*Enabling the non-coverage-based handover*/
SET UMBSCCRRM: MbscNcovHoOn2GldInd=ON, LoadHoOn3G2GldInd=ON;
/*Enabling the inter-RAT handover*/
SET UCORRMALGOSWITCH:
HoSwitch=HO_INTER_RAT_CS_OUT_SWITCH-1&HO_INTER_RAT_PS_OUT_SWITCH-1;
/*Enabling UL and DL load reshuffling (LDR) on the Uu interface*/
MOD UCELLALGOSWITCH: CellId=0, NBMLdcAlgoSwitch=UL_UU_LDR-1&DL_UU_LDR-1;
/*Configuring LDR actions*/
MOD UCELLLDR: CellId=0, DlLdrFirstAction=CSInterRatShouldBeLDHO,
DlLdrSecondAction=PSInterRatShouldBeLDHO,
DlLdrThirdAction=CSInterRatShouldNotLDHO,
DlLdrFourthAction=PSInterRatShouldNotLDHO,
UlLdrFirstAction=CSInterRatShouldBeLDHO,
UlLdrSecondAction=PSInterRatShouldBeLDHO,
UlLdrThirdAction=CSInterRatShouldNotLDHO,
UlLdrFourthAction=PSInterRatShouldNotLDHO;
//Configuration on the BSC side
/*Enabling the Handover Enhancement Based on Iur-g*/
SET GCELLHOINTERRATLDB: IDTYPE=BYID, CELLID=0, OutSysLoadHoEn=YES;
/*Enabling the inter-RAT handover*/
SET GCELLHOBASIC: IDTYPE=BYID, CELLID=0, INTERRATOUTBSCHOEN=YES,
INTERRATINBSCHOEN=YES;
/*Setting 2G Load Adjustment Coefficient*/
SET GCELLHOINTERRATLDB: IDTYPE=BYID, CELLID=0, G2GLoadAdjustCoeff=10;
//Deactivating UMTS Handover based on Load Enhancement
//Configuration on the RNC side
SET UMBSCCRRM: MbscNcovHoOn2GldInd=OFF, LoadHoOn3G2GldInd=OFF;
//Configuration on the BSC side
SET GCELLHOINTERRATLDB: IDTYPE=BYID, CELLID=0, OutSysLoadHoEn=NO;
266
Assisted Cell Change) Procedure Optimization
Configuring NACC(Network
Based on Iur-g
This section describes how to activate, verify, and deactivate the optional feature WRFD-070005
NACC Procedure Optimization Based on Iur-g.
Prerequisites
l Dependencies on Hardware
The BSC model is the BSC6900.
A GSM+UMTS dual-mode MS is required.
Interface board FG2a/FG2c/GOUa/GOUc should be configured to support Iur-g.
l Dependencies on Other Features
Configurations of other features on which this feature depends are complete. This
feature depends on features WRFD-020303 Inter-RAT Handover Based on Coverage,
WRFD-020305 Inter-RAT Handover Based on Service, WRFD-020306 Inter-RAT
Handover Based on Load, GBFD-511102 NACC Procedure Optimization Based on Iur-
g between GSM and WCDMA, or WRFD-021200 HCS (Hierarchical Cell Structure).
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others
UEs must support NACC procedure.
IP transmission mode is used on the Iur-g interface.
The MS supports NACC.
Both the 2G network and the 3G network are deployed.
A GSM cell and a UMTS cell are configured and the GSM cell is configured as the
neighboring cell of the UMTS cell.
Data is negotiated and planned for the inter-BSC6900 Iur-g interface. For details you
can refer to Configuring the inter-BSC6900 Iur-g interface.
NOTE
l The licenses on the BSC and the RNC sides are activated separately.
Context
With this feature, the network assisted cell change (NACC) procedure is performed through the
internal information exchange mechanism of the MBSC. As a result, the interoperability of PS
services between GSM cells and UMTS cells under the same MBSC does not involve the CN.
In this manner, the time taken to perform the NACC procedure is shortened by about 680ms and
therefore the handover delay is reduced. In addition, the NACC procedure does not require the
support of the CN.
Procedure
l Activation Procedure
1. Configuration on the RNC side
a. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME
single configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to enable the NACC function. In this step, select
HO_INTER_RAT_PS_3G2G_CELLCHG_NACC_SWITCH in the
HandOver switch drop-down list box.
b. Run the BSC6900 MML command SET UMBSCCRRM (CME single
configuration: UMTS Radio Global Configuration Express > MBMS
Configuration > MBSC Comm-RRM Algorithm Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches) to enable
direct GERAN system information exchange. In this step, set GERAN System
Information Exchange Switch to ON.
c. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME
single configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to enable the inter-RAT handover. In this step, select
HO_INTER_RAT_CS_OUT_SWITCH and
HO_INTER_RAT_PS_OUT_SWITCH in the HandOver switch drop-down
list box.
d. Run the BSC6900 MML command MOD UEXT2GCELL (CME single
configuration: Object Group > UMTS Service Configuration and
Maintenance Management > External Cell Configuration > RNC 2G
External Cell; CME batch modification center: 3.19 Modifying RNC External
Cell Parameters in Batches) to enable the inter-RAT cell to support indication
of the RIM procedure. In this step, set Inter-RAT cell support RIM
indicator to TRUE. If multiple neighboring cells are planned, repeat this step
to enable the inter-RAT cell to support indication of the RIM for all the
neighboring cells.
2. Configuration on the BSC side
For the configuration on the BSC side you can refer to GBFD-511102 Configuring
NACC(Network Assisted Cell Change) Procedure Optimization Based on Iur-g
between GSM and WCDMA.
l Verification Procedure
1. Trace Iur-g and Um interfaces on the LMT.
2. Use a dual-mode MS to download data in the UMTS cell and then switch the MS to
the GSM cell.
3. Check that INFO_EXCHG_INIT_REQ and INFO_EXCHG_INIT_RSP
messages are reported on the Iur-g interface. The value of informationTypeItem in
the INFO_EXCHG_INIT_REQ message is nACC-Related-Data(8) and the
INFO_EXCHG_INIT_RSP message contains nACC-Related-Data.
l Deactivation Procedure
1. Configuration on the RNC side
a. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME
single configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) on the RNC to deactivate NACC Procedure
Optimization. In this step, deselect
HO_INTER_RAT_PS_3G2G_CELLCHG_NACC_SWITCH in the
HandOver switch drop-down list box.
----End
Example
//Activating NACC Procedure Optimization
//Configuration on the RNC side
/*Enabling the NACC function*/
SET UCORRMALGOSWITCH:
HoSwitch=HO_INTER_RAT_PS_3G2G_CELLCHG_NACC_SWITCH-1;
/*Enabling direct GERAN system information exchange*/
SET UMBSCCRRM: MbscReqGeranInfoSwitch=ON;
/*Enabling the inter-RAT handover*/
SET UCORRMALGOSWITCH:
HoSwitch=HO_INTER_RAT_CS_OUT_SWITCH-1&HO_INTER_RAT_PS_OUT_SWITCH-1;
/*Enabling the inter-RAT cell to support indication of the RIM
procedure*/
MOD UEXT2GCELL: GSMCellIndex=0, SuppRIMFlag=TRUE;
//Configuration on the BSC side
/*Allowing NACC-related information exchange on the Iur-g interface*/
MOD GNRNC: RNCINDEX=0, SPTINFOEXCHG=YES, INFOEXCHGLIST=NACCRELATED-1;
/*Setting basic GPRS attributes of the GSM cell*/
SET GCELLGPRS: IDTYPE=BYID, CELLID=0, GPRS=SupportAsInnPcu, NACCSPT=YES;
//Deactivating NACC Procedure Optimization
//Configuration on the RNC side
SET UCORRMALGOSWITCH:
HoSwitch=HO_INTER_RAT_PS_3G2G_CELLCHG_NACC_SWITCH-0;
This section describes how to activate, verify, and deactivate the optional feature WRFD-070006
GSM and UMTS Load Balancing Based on Iur-g.
Prerequisites
l Dependencies on Hardware
The BSC model is the BSC6900.
A GSM+UMTS dual-mode MS is required.
Interface board FG2a/FG2c/GOUa/GOUc should be configured to support Iur-g.
l Dependencies on Other Features
Configurations of other features on which this feature depends are complete. This
feature depends on features GBFD-511103 GSM and UMTS Load Balancing Based on
Iur-g, WRFD-020400 DRD Introduction Package and WRFD-020305 Inter-RAT
Handover Based on Service.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others
2G and 3G networks cover the same area.
IP transmission mode is used over the Iur-g interface.
A GSM cell and a UMTS cell are configured, and the GSM cell is configured as a
neighboring cell of the UMTS cell.
Data is negotiated and planned for the inter-BSC6900 Iur-g interface. For details you
can refer to Configuring the inter-BSC6900 Iur-g interface.
NOTE
l The licenses on the BSC and RNC sides are activated separately.
Context
This feature implements RRC redirection and the load-based GSM/UMTS handover through
the exchange of Huawei proprietary IE over the Iur-g interface. The Iur-g protocol stack complies
with the 3GPP specifications. With this feature, the traffic is distributed on the basis of the service
handover indicator and the load of the GSM network and UMTS network during RRC connection
setup or after RAB setup. In this way, a load balance is achieved between the GSM network and
UMTS network.
Procedure
l Activation Procedure
1. Configuration on the RNC side
a. Run the BSC6900 MML command SET UMBSCCRRM (CME single
configuration: UMTS Radio Global Configuration Express > MBMS
Configuration > MBSC Comm-RRM Algorithm Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches) to enable
load balancing and set load difference thresholds. In this step, set Service
Distribution and Load Balancing Switch to LOAD-BASED(LOAD-
BASED), Load Difference Threshold Between 3G And 2G of CS Service to
10, PS Load Difference Threshold Between 3G And 2G of Ps Service to 30,
and Adjustment Coefficient of 2G Load Value to 1.
b. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME
single configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to enable inter-RAT handover. In this step, select the
HO_INTER_RAT_CS_OUT_SWITCH and
HO_INTER_RAT_PS_OUT_SWITCH check boxes under the parameter
HandOver switch.
2. Configuration on the BSC side
a. Run the BSC6900 MML command SET GCELLHOINTERRATLDB (CME
single configuration: Cell Configuration Express > Handover Data > Inter-
RAT Handover Parameters; CME batch modification center: Modifying GSM
Cell Parameters in Batches) to turn on the load balancing switch and set the load
adjustment coefficient. In this step, set Allow Inter-RAT Load HO in Access
State to Load-based(Load-based), and set 2G Load Adjustment
Coefficient to 10.
b. Run the BSC6900 MML command SET OTHSOFTPARA (CME single
configuration: GSM Global Configuration Express > Software Parameter
Configuration > Other Software Parameters of BSC; CME batch
modification center: Modifying GBSC Parameters in Batches). In this step, set
CS 2G 3G Load Balance Delta Threshold to 110.
l Verification Procedure
NOTE
If the verification achieves the following results as expected, the configuration succeeds. Otherwise, the
configuration fails.
1. 3G-to-2G Load Balancing
CAUTION
The verification can be done when only the UMTS cell is in the basic congestion state.
a. The verification procedure consists of the RRC setup phase and the RAB
connection phase. The verification in the latter phase involves CS speech services
and PS data services.
a. Verifying that CS speech services in UMTS cell1 are handed over to GSM
cell2 at the RRC setup phase
1) Use the dual-mode MS to call a fixed telephone in cell1. The call is
successfully established. Initiate Uu-interface signaling tracing on the
LMT. The RRC_RRC_CONNECT_REQ and
RRC_RRC_CONN_REJECT messages are reported, and the
RRC_RRC_CONN_REJECT message contains GSM-
TargetCellInfo. That is, information about cell2 is contained,
indicating that the MS accesses cell2.
b. Verifying that PS data services in UMTS cell1 are handed over to GPRS
cell3 at the RAB connection phase
1) Use the MS to browse the Internet.
2) Initiate Uu-interface message tracing on the LMT. You can find that
the messages RRC_RB_SETUP, RRC_RB_SETUP_CMP,
RRC_MEAS_CTRL, and
RRC_CELL_CHANGE_ORDER_FROM_UTRAN are reported, and
that the value of InterRATEvent in the RRC_MEAS_CTRL message
is event3c.
3) Initiate Iu-interface signaling tracing on the LMT. You can find that
the RANAP_SRNS_CONTEXT_REQ message is sent from the CN
to the RNC and then the RANAP_SRNS_CONTEXT_RESP message
is sent from the RNC to the CN.
4) Initiate Iu-interface signaling tracing on the LMT. You can find that
the RANAP_SRNS_DATA_FORWARD_COMMAND and
RANAP_IU_RELEASE_COMMAND messages are sent from the
CN to the RNC and then the RANAP_IU_RELEASE_COMPLETE
message is sent from the RNC to the CN.
5) When the MS attempts to reselect cell3, Internet browsing is slightly
affected. After the MS reselects cell3, Internet browsing returns to
normal.
c. Verifying that CS speech services in UMTS cell1 are handed over to GSM
cell2 at the RAB connection phase
1) Use the dual-mode MS to call a fixed telephone in cell1. The call is
successfully established.
2) Initiate Uu-interface tracing on the LMT. You can find that the
messages RRC_RB_SETUP, RRC_RB_SETUP_CMP,
RRC_MEAS_CTRL, and RRC_HO_FROM_UTRAN_CMD_GSM
are reported, and that the value of InterRATEvent in the
RRC_MEAS_CTRL message is event3c.
3) Initiate Iu-interface signaling tracing on the LMT. You can find that
the RANAP_RELOCATION_REQUIRED message is sent from the
RNC to the CN and then the RANAP_RELOCATION_COMMAND
and RANAP_IU_RELEASE_COMMAND messages are sent from
the CN to the RNC.
4) Initiate Iu-interface signaling tracing on the LMT. You can find that
the RANAP_IU_RELEASE_COMPLETE message is sent from the
RNC to the CN.
2. 2G-to-3G Load Balancing
CAUTION
The verification can be done when only the GSM cell is in the basic congestion state.
a. Use the MS to initiate a call in the GSM cell. The directed retry procedure is
triggered so that the MS accesses the neighboring UMTS cell. The call is
successfully established. Initiate A-interface signaling tracing on the LMT. You
can find that the Assignment Request, Handover Required, and Handover
Command messages are reported and that the value of cause in the Handover
Required message is directed-retry(13).
l Deactivation Procedure
1. Configuration on the RNC side
a. Run the BSC6900 MML command SET UMBSCCRRM (CME single
configuration: UMTS Radio Global Configuration Express > MBMS
Configuration > MBSC Comm-RRM Algorithm Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches) to
deactivate MBSC load balancing. In this step, set Service Distribution and
Load Balancing Switch to OFF(OFF).
2. Configuration on the BSC side
For the deactivation procedure on the BSC side you can refer to GBFD-511103
Configuring GSM and UMTS Load Balancing Based on Iur-g.
----End
Example
//Activating Load Balancing Based on Iur-g
//Configuration on the RNC side
/*Enabling load balancing and setting load difference thresholds*/
SET UMBSCCRRM: MbscServiceDiffLdbSwitch=LOAD-BASED,
Mbsc3G2GLdBlcCsDeltaThrd=10, Mbsc3G2GLdBlcPsDeltaThrd=30;
/*Enabling inter-RAT handover*/
SET UCORRMALGOSWITCH:
HoSwitch=HO_INTER_RAT_CS_OUT_SWITCH-1&HO_INTER_RAT_PS_OUT_SWITCH-1;
//Configuration on the BSC side
/*Enabling load balancing*/
SET GCELLHOINTERRATLDB: IDTYPE=BYID, CELLID=0, OutSysLoadHoEn=YES,
InterRatServiceLoadHoSwitch=Load-based, G2GLoadAdjustCoeff=10;
/*Enabling inter-RAT handover*/
SET GCELLHOBASIC: IDTYPE=BYNAME, CELLNAME="0", INTERRATOUTBSCHOEN=YES,
INTERRATINBSCHOEN=YES;
/*Setting load difference thresholds*/
SET OTHSOFTPARA: G2G3GLdBlcDeltaThrd=110;
//Deactivating Load Balancing Based on Iur-g
//Configuration on the RNC side
SET UMBSCCRRM: MbscServiceDiffLdbSwitch=OFF;
//Configuration on the BSC side
This section describes how to activate, verify, and deactivate the optional feature WRFD-070007
GSM and UMTS Traffic Steering Based on Iur-g.
Prerequisites
l Dependencies on Hardware
The BSC model is the BSC6900.
A GSM+UMTS dual-mode MS is required.
Interface board FG2a/FG2c/GOUa/GOUc should be configured to support Iur-g.
l Dependencies on Other Features
Configurations of other features on which this feature depends are complete. This
feature depends on features GBFD-511104 GSM and WCDMA Traffic Steering Based
on Iur-g, WRFD-020400 DRD Introduction Package and WRFD-020305 Inter-RAT
Handover Based on Service.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others
2G and 3G networks cover the same area.
IP transmission mode is used over the Iur-g interface.
A GSM cell and a UMTS cell are configured, and the GSM cell is configured as a
neighboring cell of the UMTS cell.
Data is negotiated and planned for the inter-BSC6900 Iur-g interface. For details you
can refer to Configuring the inter-BSC6900 Iur-g interface.
NOTE
l The licenses on the BSC and RNC sides are activated separately.
Context
This feature supports RRC redirection and GSM/UMTS inter-RAT handover based on service.
With this feature, services are steered on the basis of the service handover indicator, hierarchical
network planning, and the load of the GSM network and UMTS network when an MS accesses
the network. Service steering enables UEs requesting speech or low-speed PS services to access
the GSM network and those requesting high-speed PS services to access the UMTS network.
Procedure
l Activation Procedure
1. Configuration on the RNC side
a. Run the BSC6900 MML command SET UMBSCCRRM (CME single
configuration: UMTS Radio Global Configuration Express > MBMS
Configuration > MBSC Comm-RRM Algorithm Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches) to enable
traffic steering. In this step, set Service Distribution and Load Balancing
Switch to SERVICE-BASED(SERVICE-BASED) and Adjustment
Coefficient of 2G Load Value to 1.
b. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME
single configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to enable inter-RAT handover. In this step, select the
HO_INTER_RAT_CS_OUT_SWITCH and
HO_INTER_RAT_PS_OUT_SWITCH check boxes under the parameter
HandOver switch.
c. Run the BSC6900 MML command ADD UCELLHOCOMM (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Oriented Handover Common Algorithm Parameters; CME batch
modification center: 3.18 Modifying UMTS Cell Parameters in Batches) to
enable inter-RAT CS handover. In this step, set Inter-RAT CS Handover
Switch to ON. Run the ADD UCELLHOCOMM (CME single configuration:
UMTS Cell Configuration Express > Cell Parameters > Cell Oriented
Handover Common Algorithm Parameters; CME batch modification center:
3.18 Modifying UMTS Cell Parameters in Batches) command to enable inter-
RAT CS handover for each cell.
2. Configuration on the BSC side
For the configuration on the BSC side you can refer to GBFD-511104 Configuring
GSM and WCDMA Traffic Steering Based on Iur-g.
l Verification Procedure
1. The verification procedure of 3G-to-2G Traffic Steering
CAUTION
The verification can be done when only the UMTS cell is in the basic congestion state.
a. Use the dual-mode MS to call a fixed telephone in the UMTS cell. Initiate Iu-
interface tracing on the LMT. You can find that the
RANAP_RELOCATION_REQUIRED message is reported and the handover
cause value in the message is resource-optimisation-relocation. Initiate A
interface tracing. You can find that the Handover Request message is reported
and the handover cause value in the message is traffic.
CAUTION
Ensure that the GSM cell is not in the congestion state.
CAUTION
The verification can be done when only the GSM cell is in the basic congestion state.
a. Use the dual-mode MS to call a fixed telephone in the GSM cell. Initiate CS
Domain Messages of a Single Subscriber tracing on the LMT. You can find that
the call is in GSM cell, and don't hand over to UMTS cell.
l Deactivation Procedure
1. Configuration on the RNC side
a. Run the BSC6900 MML command SET UMBSCCRRM (CME single
configuration: UMTS Radio Global Configuration Express > MBMS
Configuration > MBSC Comm-RRM Algorithm Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches) to
deactivate traffic steering. In this step, set Service Distribution and Load
Balancing Switch to OFF(OFF).
----End
Example
//Activating 3G-to-2G traffic steering
//Configuration on the RNC side
/*Enabling traffic steering*/
SET UMBSCCRRM: MbscServiceDiffLdbSwitch=SERVICE-BASED;
/*Enabling inter-RAT handover*/
SET UCORRMALGOSWITCH:
HoSwitch=HO_INTER_RAT_CS_OUT_SWITCH-1&HO_INTER_RAT_PS_OUT_SWITCH-1;
/*Enabling inter-RAT CS handover*/
ADD UCELLHOCOMM: CellId=1, CSServiceHOSwitch=ON;
//Configuration on the BSC side
/*Enabling inter-RAT incoming BSC handover*/
SET GCELLHOINTERRATLDB: IDTYPE=BYID, CELLID=0,
InterRatServiceLoadHoSwitch=Service-based;
//Deactivating 3G-to-2G traffic steering
//Configuration on the RNC side
SET UMBSCCRRM: MbscServiceDiffLdbSwitch=OFF;
This section describes how to activate, verify, and deactivate the optional feature WRFD-020303
Inter-RAT Handover Based on Coverage.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The UE supports relevant measurements and the handover procedure.
Context
This feature supports measurement-based inter-RAT handover triggered by event 2D or uplink
UE QoS and urgent blind inter-RAT handover triggered by event 1F. This type of handover is
applicable to inter-RAT interworking based on coverage or caused by moving UEs.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, select
HO_INTER_RAT_CS_OUT_SWITCH and
HO_INTER_RAT_PS_OUT_SWITCH from the HandOver Switch list.
2. Run the BSC6900 MML command ADD U2GNCELL (CME single configuration:
UMTS Cell Configuration Express > Neighboring Cell > GSM Neighboring
NOTE
Example
//Activating Inter-RAT Handover Based on Coverage
SET UCORRMALGOSWITCH:
HoSwitch=HO_INTER_RAT_CS_OUT_SWITCH-1&HO_INTER_RAT_PS_OUT_SWITCH-1;
MOD UTYPRABBASIC: RabIndex=0, SHInd=HO_TO_GSM_SHOULD_NOT_BE_PERFORM;
//Deactivating Inter-RAT Handover Based on Coverage
SET UCORRMALGOSWITCH:
HoSwitch=HO_INTER_RAT_CS_OUT_SWITCH-0&HO_INTER_RAT_PS_OUT_SWITCH-0;
This section describes how to activate, verify, and deactivate the optional feature WRFD-020309
Inter-RAT Handover Based on DL QoS.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others
The UE supports relevant measurements and the handover procedure.
Context
When the load of voice and PS BE services is high in a cell and downlink QoS decreases, this
feature enables the UE to be handed over to an inter-RAT cell, guaranteeing QoS requirements.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, set HandOver Switch to
HO_INTER_RAT_CS_OUT_SWITCH and
HO_INTER_RAT_PS_OUT_SWITCH.
2. Run the BSC6900 MML command ADD U2GNCELL (CME single configuration:
UMTS Cell Configuration Express > Neighboring Cell > GSM Neighboring
Cell; CME batch modification center: not supported) to add an inter-RAT neighboring
cell.
3. Run the BSC6900 MML command SET UQOSHO (CME single configuration:
UMTS Radio Global Configuration Express > QOS Parameter Configuration >
RNC Oriented QoS Handover Measurement Algorithm Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches) to set
BSC6900-level parameters related to Inter-RAT Handover Based on DL QoS.
4. Run the BSC6900 MML command SET UQOSACT (CME single configuration:
UMTS Radio Global Configuration Express > QOS Parameter Configuration >
RNC-Oriented QoS Enhancement Algorithm Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches) to turn on QoS
switches for different traffic classes.
l Verification Procedure
1. Log in to the BSC6900 LMT and start Uu Interface Trace.
2. Ensure that the RNC sends to the NodeB an NBAP_DEDI_MEAS_INIT_REQ
message, which carries the event E parameter, as shown in Figure 270-1.
modification center: 3.15 Modifying RNC Parameters in Batches) to turn off QoS
switches for different traffic classes.
----End
Example
//Activating Inter-RAT Handover Based on DL QoS
SET UCORRMALGOSWITCH:
HoSwitch=HO_INTER_RAT_CS_OUT_SWITCH-1&HO_INTER_RAT_PS_OUT_SWITCH-1;
SET UQOSACT: BEQosPerform=YES, AMRQosPerform=YES, VPQosPerform=YES,
BeDlAct1=InterRatHO, DlQosAmrInterRatHoSwitch=YES,
DlQosWAmrInterRatHoSwitch=YES;
//Deactivating Inter-RAT Handover Based on DL QoS
SET UCORRMALGOSWITCH:
HoSwitch=HO_INTER_RAT_CS_OUT_SWITCH-0&HO_INTER_RAT_PS_OUT_SWITCH-0;
SET UQOSACT: BEQosPerform=NO, AMRQosPerform=NO, VPQosPerform=NO;
This section describes how to activate, verify, and deactivate the optional feature WRFD-020307
Video Telephony Fallback to Speech (AMR) for Inter-RAT HO.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
One or multiple of the following features must be configured before this feature is
activated:
WRFD-020303 Inter-RAT Handover Based on Coverage
WRFD-020305 Inter-RAT Handover Based on Service
WRFD-020306 Inter-RAT Handover Based on Load
WRFD-021200 HCS (Hierarchical Cell Structure)
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others
The UE needs to be compliant with 3GPP Release 6 to support the feature.
The MSC needs to be compliant with 3GPP Release 6 to support the feature.
Context
Before videophone services are handed over to the 2G system, this feature enables the fallback
of video telephony to speech to ensure continuous calls. However, due to the limitation of UE
and network support capability, the service may not be implemented. Therefore, Service Change
and UDI Fallback (SCUDIF) is introduced in 3GPP Release 6 to provide the mechanism to
provide the mechanism to fall back to speech without experiencing call drops in these scenarios.
Procedure
l Activation Procedure
The license controlling this feature has been activated. For details on how to activate the
license, see 4 Activating the UMTS License. For details about license items, see 2 Feature
Activation and License Item Descriptions.
l Verification Procedure
1. Start Iu Interface Trace and Uu Interface Trace on the BSC6900 LMT.
2. After videophone services are established, check in the Uu Interface Trace dialog
box that the UE sends to the BSC6900 an RRC_MEAS_RPRT message, which
contains the 3A report.
3. In the Iu Interface Trace dialog box, check that the BSC6900 sends an
RAB_MODIFY_REQ message to the CN. In the RAB_MODIFY_REQ message,
the value of the IE alternativeRABConfigurationRequest is alternative-RAB-
configuration-Requested.
l Deactivation Procedure
This feature does not need to be deactivated.
----End
This section describes how to activate, verify, and deactivate the optional feature WRFD-020308
Inter-RAT Handover Phase 2.
Prerequisites
l Dependencies on Hardware
BSC should support NACC RIM (RAN Information Management) and PS handover
procedure.
l Dependencies on Other Features
This feature is required only when one or several of the following inter-RAT handover
features are introduced:
WRFD-020303 Inter-RAT Handover Based on Coverage
WRFD-020305 Inter-RAT Handover Based on Service
WRFD-020306 Inter-RAT Handover Based on Load
WRFD-021200 HCS (Hierarchical Cell Structure)
l License
This feature is not under license control.
l Others
UE should support NACC and PS handover procedure.
GSM BSC should support NACC RIM (RAN Information Management) and PS
handover procedure.
SGSN supports NACC and PS handover procedure.
Context
This feature provides the inter-RAT relocation procedure for NACC and PS services to shorten
the interruption time of PS services caused by inter-RAT handover.
Procedure
l For details about how to activate, verify, and deactivate this feature, see the following
sections:
273 Configuring NACC(Network Assisted Cell Change)
274 Configuring PS Handover between UMTS and GPRS
----End
This section describes how to activate, verify, and deactivate the optional feature
WRFD-02030801 NACC(Network Assisted Cell Change).
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The configurations of the features on which this feature depends are complete. This
feature depends on the feature WRFD-020308 PS Inter-RAT Handover Phase 2.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others
UE should support NACC procedure.
GSM BSC should support NACC RIM (RAN Information Management).
SGSN should support NACC procedure.
Context
This feature supports the standard NACC procedure defined in 3GPP specifications.
The NACC refers to Network Assisted Cell Change from UTRAN to GERAN, which is different
from the normal cell change order procedure, because the network provides GERAN (P) SI for
the UE.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
----End
Example
//Activating NACC(Network Assisted Cell Change)
SET UCORRMALGOSWITCH:
HoSwitch=HO_INTER_RAT_PS_3G2G_CELLCHG_NACC_SWITCH-1&HO_INTER_RAT_PS_3G2G_
RELOCATION_SWITCH-0&HO_INTER_RAT_PS_OUT_SWITCH-1;
//Deactivating NACC(Network Assisted Cell Change)
MOD UEXT2GCELL: SuppRIMFlag=FALSE;
This section describes how to activate, verify, and deactivate the optional feature
WRFD-02030802 PS Handover between UMTS and GPRS.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The configurations of the features on which this feature depends are complete. This
feature depends on the feature WRFD-020308 PS Inter-RAT Handover Phase 2.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others
UE should support PS handover procedure.
GSM BSC should support PS handover procedure.
SGSN should support PS handover procedure.
Context
This feature enables the relocation of PS services (including non-real-time PS services and real-
time PS services) between systems. In inter-system handover scenarios, this feature can greatly
improve user perception, especially for real-time PS services.
The PS handover is different from NACC or normal cell change function, with which the
relocation procedure between 3G and 2G is applied, just like the CS inter-system handover. With
this feature, the service interruption for PS service inter-system handover is reduced by a great
extent.
In this feature, both the handover from UTRAN to GERAN and the handover from GERAN to
UTRAN are supplied. If both the UE and the network support PS handover, handover between
UTRAN and GERAN would be performed. Otherwise, either NACC or normal cell change order
would be selected.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to open the following switches in the HandOver switch
parameter:
HO_INTER_RAT_PS_OUT_SWITCH
HO_INTER_RAT_PS_3G2G_RELOCATION_SWITCH
2. Run the BSC6900 MML command ADD UEXT2GCELL (CME single
configuration: Object Group > UMTS Service Configuration and Maintenance
Management > External Cell Configuration > RNC 2G External Cell; CME batch
modification center: 3.19 Modifying RNC External Cell Parameters in Batches)
to add a neighboring GSM cell to the UMTS coverage and to set the Inter-RAT cell
support PS HO indicator parameter to TRUE.
3. Run the BSC6900 MML command ADD U2GNCELL (CME single configuration:
UMTS Cell Configuration Express > Neighboring Cell > GSM Neighboring
Cell; CME batch modification center: not supported) to add a neighboring GSM cell
for the UMTS cell.
4. Optional: Run the BSC6900 MML command SET UINTERRATHOCOV (CME
single configuration: UMTS Radio Global Configuration Express > HandOver
Parameter Configuration > RNC Oriented Coverage based Inter-rat Handover
Measurement Algorithm Parameters; CME batch modification center: 3.15
Modifying RNC Parameters in Batches) to set inter-RAT handover measurement
related parameters.
l Verification Procedure
1. Run the BSC6900 MML command LST UCORRMALGOSWITCH to check the
status of PS inter-RAT handover switch and the Relocation HO switch.
2. Run the BSC6900 MML command LST UEXT2GCELL to ensure the inter-RAT
cell supports PS Handover.
3. Run the BSC6900 MML command LST UINTERRATHOCOV to check inter-RAT
handover measurement related parameters.
l Deactivation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to set
HO_INTER_RAT_PS_3G2G_RELOCATION_SWITCH in the HandOver
switch parameter to 0.
2. Run the BSC6900 MML command MOD UEXT2GCELL (CME single
configuration: Object Group > UMTS Service Configuration and Maintenance
Management > External Cell Configuration > RNC 2G External Cell; CME batch
modification center: 3.19 Modifying RNC External Cell Parameters in Batches)
to set the SuppPSHOFlag parameter to FALSE.
----End
Example
//Activating PS Handover between UMTS and GPRS
SET UCORRMALGOSWITCH:
HoSwitch=HO_INTER_RAT_PS_3G2G_RELOCATION_SWITCH-1&HO_INTER_RAT_PS_OUT_SWI
TCH-1;
ADD UEXT2GCELL: GSMCellIndex=1, GSMCellName="GSMCELL1", NBscIndex=1,
LdPrdRprtSwitch=ON, MCC="460", MNC="01", CnOpGrpIndex=1, LAC=1,
CfgRacInd=REQUIRE, RAC=1, CID=1, NCC=1, BCC=1, BcchArfcn=512,
RatCellType=GPRS, UseOfHcs=NOT_USED, SuppPSHOFlag=TRUE;
ADD U2GNCELL: RNCId=1, CellId=100, GSMCellIndex=1;
SET UINTERRATHOCOV: InterRatReportMode=PERIODICAL_REPORTING,
FilterCoefOf2D2F=D4, InterRATFilterCoef=D6;
//Deactivating PS Handover between UMTS and GPRS
SET UCORRMALGOSWITCH: HoSwitch=HO_INTER_RAT_PS_3G2G_RELOCATION_SWITCH-0;
MOD UEXT2GCELL: SuppPSHOFlag=FALSE;
This section describes how to activate, verify, and deactivate the optional feature WRFD-020305
Inter-RAT Handover Based on Service.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature provides a mechanism for performing handover between GSM/GPRS and UMTS
systems on the basis of services. This feature forwards appropriate services in a UMTS system
to a GSM/GPRS system, balancing load between the two systems. This feature also prevents
the handover from adversely affecting services based on service attributes.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, select
HO_INTER_RAT_CS_OUT_SWITCH and
HO_INTER_RAT_PS_OUT_SWITCH from the HandOver Switch list.
2. Run the BSC6900 MML command ADD UEXT2GCELL (CME single
configuration: Object Group > UMTS Service Configuration and Maintenance
Management > External Cell Configuration > RNC 2G External Cell; CME batch
l Deactivation Procedure
1. Run the BSC6900 MML command MOD UCELLHOCOMM (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Example
//Activating Inter-RAT Handover Based on Service
SET UCORRMALGOSWITCH:
HoSwitch=HO_INTER_RAT_CS_OUT_SWITCH-1&HO_INTER_RAT_PS_OUT_SWITCH-1;
ADD UCELLHOCOMM: CellId=111, CSServiceHOSwitch=ON, PSServiceHOSwitch=ON;
//Deactivating Inter-RAT Handover Based on Service
MOD UCELLHOCOMM: CellId=111, CSServiceHOSwitch=OFF, PSServiceHOSwitch=OFF;
This section describes how to activate, verify, and deactivate the optional feature WRFD-020306
Inter-RAT Handover Based on Load.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
If this feature is used for HSDPA or HSUPA load control, the feature WRFD-010610
HSDPA Introduction Package or WRFD-010612 HSUPA Introduction Package has
been configured correspondingly before this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature is an important part of Load Reshuffling (LDR). It enables some UEs in a UMTS
cell to be blindly handed over to a GSM or GPRS cell to reduce the load of the UMTS cell.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to activate the inter-RAT handover. In this step, select the
HO_INTER_RAT_CS_OUT_SWITCH and
HO_INTER_RAT_PS_OUT_SWITCH check boxes under the parameter
HandOver Switch.
2. Run the BSC6900 MML command ADD UEXT2GCELL (CME single
configuration: Object Group > UMTS Service Configuration and Maintenance
Management > External Cell Configuration > RNC 2G External Cell; CME batch
modification center: 3.19 Modifying RNC External Cell Parameters in Batches)
to add the information about a GSM cell.
3. Run the BSC6900 MML command ADD U2GNCELL (CME single configuration:
UMTS Cell Configuration Express > Neighboring Cell > GSM Neighboring
Cell; CME batch modification center: not supported) to add the GSM cell as a
neighboring cell of the UMTS cell.
4. Run the BSC6900 MML command ADD UCELLLDR (CME single configuration:
UMTS Cell Configuration Express > Cell Parameters > Cell LDR Algorithm
Parameters; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches) to set the inter-RAT handover policy for the UMTS cell. In
this step, set DL LDR fourth action to CSInterRatShouldBeLDHO(CS domain
inter-rat should be load handover), DL LDR fifth action to
PSInterRatShouldBeLDHO(PS domain inter-rat should be load handover), UL
LDR fourth action to CSInterRatShouldBeLDHO(CS domain inter-rat should
be load handover), and UL LDR fifth action to PSInterRatShouldBeLDHO(PS
domain inter-rat should be load handover).
5. Run the BSC6900 MML command ADD UCELLINTERRATHONCOV (CME
single configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
Oriented None-Coverage Based Inter-rat Handover Measurement Algorithm
Parameters; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches) (at the cell level) or SET UINTERRATHONCOV (CME
single configuration: UMTS Radio Global Configuration Express > HandOver
Parameter Configuration > RNC Oriented None-Coverage based Inter-rat
Handover Measurement Algorithm Parameters; CME batch modification center:
3.15 Modifying RNC Parameters in Batches) (at the RNC level) to configure
parameters related to non-coverage-based inter-frequency handover to GSM.
l Verification Procedure
1. Initiate Iu interface message tracing and Uu interface message tracing on the
BSC6900 LMT.
2. Use a UE in the UMTS cell to call another UE in the same cell. The call is set up
successfully.
3. Run the BSC6900 MML command MOD UCELLLDM to reduce the downlink LDR
threshold.
The following messages can be traced on the Iu interface: the
RANAP_RELOCATION_REQUIRED message from the RNC to the CN, and the
RANAP_RELOCATION_COMMAND message from the CN to the RNC.
The following message can be traced on the Uu interface: the
RRC_HO_FROM_UTRAN_CMD_GSM message from the RNC to the UE.
The following messages can be traced on the Iu interface: the
RANAP_RELOCATION_REQUIRED message from the RNC to the CN, the
RANAP_RELOCATION_COMMAND message from the CN to the RNC, the
RANAP_IU_RELEASE_COMMAND message from the CN to the RNC, and the
RANAP_IU_RELEASE_COMPLETE message from the RNC to the CN.
l Deactivation Procedure
1. Run the BSC6900 MML command MOD UCELLLDR (CME single configuration:
UMTS Cell Configuration Express > Cell Parameters > Cell LDR Algorithm
Parameters; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches) to deactivate the load-based handover. In this step, set DL
LDR fourth action, DL LDR fifth action, UL LDR fourth action, and UL LDR
fifth action to NoAct.
2. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to deactivate the inter-RAT handover. In this step, deselect
the HO_INTER_RAT_CS_OUT_SWITCH and
HO_INTER_RAT_PS_OUT_SWITCH check boxes under the parameter
HandOver Switch.
----End
Example
//Activating Inter-RAT Handover Based on Load
SET UCORRMALGOSWITCH:
HoSwitch=HO_INTER_RAT_CS_OUT_SWITCH-1&HO_INTER_RAT_PS_OUT_SWITCH-1;
ADD UEXT2GCELL: GSMCellIndex=2, GSMCellName="2", NBscIndex=2,
LdPrdRprtSwitch=OFF, MCC="460", MNC="07", CnOpGrpIndex=1, LAC=H'0012,
CfgRacInd=REQUIRE, RAC=H'01, CID=2, NCC=2, BCC=2, BcchArfcn=1000,
RatCellType=GSM, UseOfHcs=NOT_USED;
ADD U2GNCELL: RncId=1, CellId=2, GSMCellIndex=2, BlindHoFlag=TRUE,
BlindHOPrio=1, NPrioFlag=FALSE;
ADD UCELLLDR: CellId=1, DlLdrFourthAction=CSInterRatShouldBeLDHO,
DlLdrFifthAction=PSInterRatShouldBeLDHO,
UlLdrFourthAction=CSInterRatShouldBeLDHO,
UlLdrFifthAction=PSInterRatShouldBeLDHO;
ADD UCELLINTERRATHONCOV: CellId=1;
//Deactivating Inter-RAT Handover Based on Load
MOD UCELLLDR: CellId=1, DlLdrFourthAction=NoAct, DlLdrFifthAction=NoAct,
UlLdrFourthAction=NoAct, UlLdrFifthAction=NoAct;
SET UCORRMALGOSWITCH:
HoSwitch=HO_INTER_RAT_CS_OUT_SWITCH-0&HO_INTER_RAT_PS_OUT_SWITCH-0;
This section describes how to activate and verify the optional feature WRFD-020401 Inter-RAT
Redirection Based on Distance.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The feature WRFD-020400 DRD Introduction Package has been configured before this
feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
If a UE initiates a CS voice call with a long distance to the antenna of a 3G cell, the UE may
experience call drops when the UE moves out of the pilot polluted area. To solve this problem,
the RAN redirects a UE to a GSM cell based on the distance threshold when the UE initiates an
RRC connection setup request.
Procedure
l Activation Procedure
1. run the BSC6900 MML command SET UDISTANCEREDIRECTION (CME
single configuration: UMTS Radio Global Configuration Express > Directed
Retry Parameter Configuration > RNC-Oriented Delay Based RRC Redirection
Parameters; CME batch modification center: 3.15 Modifying RNC Parameters in
Batches) to set the BSC6900-level parameters.
Set Redirection Switch to ON.
Set Propagation delay threshold as specified in 3GPP TS 25.433
2. Simulate a scenario where pilot pollution occurs. Place the UE in a place where the
UE is far away from the NodeB and pilot signals are strong. Then, use the UE to
establish a CS voice call.
3. Check the messages traced on the Uu interface.
As shown in Figure 277-2, if the RRC CONNECTION REJECT message
contains the information element (IE) GSM-Targetcellinfo, the RAN has
redirected the UE to the GSM network, and this feature has been activated.
If the RRC CONNECTION REJECT message does not contain the IE GSM-
Targetcellinfo, this feature is not activated.
l Deactivation Procedure
1. run the BSC6900 MML command SET UDISTANCEREDIRECTION (CME
single configuration: UMTS Radio Global Configuration Express > Directed
Retry Parameter Configuration > RNC-Oriented Delay Based RRC Redirection
Parameters; CME batch modification center: 3.15 Modifying RNC Parameters in
Batches) to deactivate this feature in the BSC6900 level. In this step, set Redirection
Switch to OFF.
2. run the BSC6900 MML command MOD UCELLDISTANCEREDIRECTION
(CME single configuration: UMTS Cell Configuration Express > Cell
Parameters > Cell-Oriented Delay Based RRC Redirection Parameters; CME
batch modification center: 3.18 Modifying UMTS Cell Parameters in Batches) to
deactivate this feature in the cell level. In this step, set Redirection Switch to OFF.
NOTE
If cell-level redirection parameters are set for a cell, the cell-level settings take effect. If no
cell-level redirection parameters are set for the cell, the RNC-level settings take effect.
----End
Example
//Activating Inter-RAT Redirection Based on Distance
//Activating this feature in the BSC6900 level
SET UDISTANCEREDIRECTION: RedirSwitch=ON, DelayThs=100,
RedirFactorOfLDR=70, RedirFactorOfNorm=60;
//Activating this feature in the cell level
ADD UCELLDISTANCEREDIRECTION: CellId=1, RedirSwitch=ON, DelayThs=100,
RedirFactorOfLDR=80, RedirFactorOfNorm=60;
//Deactivating Inter-RAT Redirection Based on Distance
//Deactivating this feature in the BSC6900 level
SET UDISTANCEREDIRECTION: RedirSwitch=OFF;
//Deactivating this feature in the cell level
MOD UCELLDISTANCEREDIRECTION: CellId=1, RedirSwitch=OFF;
This section describes how to activate, verify, and deactivate the optional feature WRFD-020310
3G/2G Common Load Management.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature is required only when one of the following features is available:
WRFD-020305 Inter-RAT Handover Based on Service
WRFD-020306 Inter-RAT Handover Based on Load
WRFD-021200 HCS (Hierarchical Cell Structure)
WRFD-020400 DRD Introduction Package
WRFD-020308 Inter-RAT Handover Phase 2
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others
The CN supports this feature.
The BSS supports this feature.
Context
The 3G/2G Common Load Management applies to inter-RAT handover and inter system direct
retry. The load of source cell and target cell is considered during inter-RAT handover from 3G
to 2G or from 2G to 3G and inter system direct retry.
Procedure
l Activation Procedure
Consult Huawei engineers about the verification solution to obtain professional technical support.
l Deactivation Procedure
1. Run the BSC6900 MML command SET UINTERRATHONCOV (CME single
configuration: UMTS Radio Global Configuration Express > HandOver
Parameter Configuration > RNC Oriented None-Coverage based Inter-rat
Handover Measurement Algorithm Parameters; CME batch modification center:
3.15 Modifying RNC Parameters in Batches) to set the parameter Send Load Info
to GSM Ind to OFF and the parameter NCOV Reloc Ind based on GSM cell load
to OFF.
----End
Example
//Activating 3G/2G Common Load Management
SET UCORRMALGOSWITCH:
HoSwitch=HO_INTER_RAT_CS_OUT_SWITCH-1&HO_INTER_RAT_PS_OUT_SWITCH-1;
SET UINTERRATHONCOV: SndLdInfo2GsmInd=ON, NcovHoOn2GldInd=ON;
//Deactivating 3G/2G Common Load Management
SET UINTERRATHONCOV: SndLdInfo2GsmInd=OFF, NcovHoOn2GldInd=OFF;
This section describes how to activate, verify, and deactivate the optional feature WRFD-020126
Mobility Between UMTS and LTE Phase 1. For details about how to configure this feature on
the LTE side, see the related documents provided by the LTE equipment vendor. (This feature
cannot be configured using the CME. )
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The UE supports both UMTS and LTE.
The LTE network supports this feature.
Context
The feature Mobility Between UMTS and LTE Phase 1 provides the following functions:
l UMTS supports bidirectional cell reselection between a UMTS cell and an LTE cell.
l UMTS supports PS handovers from an LTE cell to a UMTS cell.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command ADD UCELLSIBSWITCH or MOD
UCELLSIBSWITCH. In this step, set SIB Switch to SIB19.
After the information about the frequencies of neighboring LTE cells is configured
and SIB Switch is set to SIB19, the BSC6900 sends SIB19 messages to UEs. The
SIB19 message contains the neighboring LTE cell list and LTE cell reselection
parameters.
2. Run the BSC6900 MML command ADD UCELLSELRESEL or MOD
UCELLSELRESEL. In this step, set Absolute priority level of the serving cell to
an appropriate value.
Inter-RAT measurement is performed based on the settings of RSCP threshold for
low-prio-freq measurement initiation and Ec/No threshold for low-prio-freq
measurement initiation. The measurement result provides a reference to cell
reselection.
3. Run the BSC6900 MML command ADD UCELLNFREQPRIOINFO or MOD
UCELLNFREQPRIOINFO to configure the information about the frequencies of
neighboring cells.
The UE makes cell reselection decisions based on the configured information about
the frequencies of neighboring cells.
4. Configure the related data, such as the neighboring cell relationships between cells,
on the LTE side.
For details about how to configure this feature on the LTE side, see the related
documents provided by the LTE equipment vendor. If the LTE equipment is provided
by Huawei, see the LTE document Mobility Management in Connected Mode
Parameter Description.
5. Run the BSC6900 MML command ADD UNODEB or MOD UNODEB. In this step,
set NodeB Protocol Version to R8 or the higher version.
l Verification Procedure
1. In the Navigation Tree pane on the BSC6900 LMT, click the Trace tab. In the
displayed Trace Navigation Tree pane, double-click UMTS Services. On the
unfolded list, double-click Uu Interface Trace. In the displayed Uu Interface
Trace dialog box, select RRC_SYS_INFO_TYPE19 to trace Uu interface SIB19
message.
l Deactivation Procedure
NOTE
To deactivate this feature, you can either turn off the SIB19 switch or deactivate the license.
l To deactivate this feature in a specific cell, you are advised to turn off the SIB19 switch.
l To deactivate this feature in all cells under a BSC6900, deactivate the license. This method is
not recommended.
1. Run the BSC6900 MML command MOD UCELLSIBSWITCH. In this step,
deselect the SIB19 check box under the parameter SIB Switch to turn off the SIB19
switch in a cell. After the switch is turned off, the BSC6900 stops sending SIB19
messages to UEs. In such a case, the configured absolute priority of the serving cell
and the configured information about the frequencies of neighboring cells become
ineffective.
2. Run the BSC6900 MML command SET LICENSE to deactivate the license
controlling the feature Mobility Between UMTS and LTE Phase 1.
----End
Example
//Activating Mobility Between UMTS and LTE Phase 1
MOD UCELLSIBSWITCH: CellId=1, SibCfgBitMap=SIB19-1;
MOD UCELLSELRESEL: CellId=1, QualMeas=CPICH_ECNO, QrxlevminExtSup=FALSE,
NonhcsInd=NOT_CONFIGURED, ThdPrioritySearch1=2, ThdPrioritySearch2=2;
MOD UCELLNFREQPRIOINFO: CellId=1, EARFCN=1, NPriority=2,
BlacklstCellNumber=D0;
MOD UNODEB: NodeBId=1, NodeBProtclVer=R9;
//Deactivating Mobility Between UMTS and LTE Phase 1
MOD UCELLSIBSWITCH: CellId=1, SibCfgBitMap=SIB19-0;
SET LICENSE: SETOBJECT=UMTS, ISPRIMARYPLMN=YES,
FUNCTIONSWITCH5=LQW1ULM01-0;
This section describes how to activate, verify, and deactivate the optional feature WRFD-020129
Service-Based PS Service Redirection from UMTS to LTE.
Prerequisites
l Dependencies on Hardware
There is no requirement for BSC6900 and NodeB.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others
The UE must support 3GPP Release 8 (Sept. 2008) or later. It also must support both
UMTS and LTE.
The SGSN support this feature.
CN should support cooperation from UMTS to LTE.
The neighboring LTE cell has been configured. For details, see Configuring a
Neighboring LTE Cell.
Context
With this feature, the operator can choose to hand over the high-speed PS services from the
UMTS network to the LTE network. This helps fully utilize the UMTS and LTE network
resources, improving the user experience.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command MOD ULTECELL (CME single configuration:
Object Group > UMTS Service Configuration and Maintenance Management >
External Cell Configuration > RNC LTE External Cell; CME batch modification
center: not supported) to set an LTE cell. In this step, set LTE Cell Supporting PS
HO Indicator to NotSupport and set BlackCell List Flag to False.
2. Run the BSC6900 MML command SET UU2LTEHONCOV (CME single
configuration: UMTS Radio Global Configuration Express > HandOver
Parameter Configuration > RNC-Oriented Non-Coverage-Based UMTS-LTE
Handover Measurement Algorithm Parameters; CME batch modification center:
not supported) to set RNC-Oriented Non-Coverage-Based UMTS-LTE Handover
Measurement Algorithm Parameters. The BSC6900 sends these parameters to the UE
by means of a measurement control message.
3. Optional: Run the BSC6900 MML command ADD UCELLU2LTEHONCOV
(CME single configuration: UMTS Cell Configuration Express > Cell
Parameters > Cell-Oriented Non-Coverage-Based UMTS-LTE Handover
Measurement Algorithm Parameters; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches) to set the cell-level non-coverage-
based UMTS-to-LTE handover measurement parameters for a cell.
4. Run the BSC6900 MML command MOD UTYPRABBASIC (CME single
configuration: UMTS Radio Global Configuration Express > Typical Service
Configuration > Basic Information for Typical Traffic Radio Access Bearer;
CME batch modification center: not supported) to modify the basic configuration of
a typical radio access bearer (RAB). In this step, set EUTRANSHIND to
HO_TO_EUTRAN_SHOULD_BE_PERFORM.
5. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to select HO_LTE_PS_OUT_SWITCH and
HO_LTE_SERVICE_PS_OUT_SWITCH from HandOver Switch drop list.
l Verification Procedure
Start Uu interface tracing on the LMT to trace messages on the Uu interface.
View the RRC_MEAS_CTRL message, as shown in Figure 280-1. If the
measurementCommand message contains the information element (IE) e-UTRA-
FrequencyInfo, this feature takes effect. The measurement control message sent by the
BSC6900 contains the LTE cell information.
After receiving the message, the UE measures the signal quality in the LTE cell. The
measurement result serves as the basis for handover decision.
View the RRC_CONN_REL message, as shown in Figure 280-2. If in the message the
rrcConnectionRelease message contains the IE EUTRA-TargetFreqInfo, the RRC
connection release message carries the LTE cell information.
After receiving this message, the UE is handed over to the LTE network and the UE
reestablishes PS services in the LTE cell.
l Deactivation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to deselect HO_LTE_SERVICE_PS_OUT_SWITCH
from the HandOver Switch drop list.
----End
Example
//Activation procedure
//Deactivation procedure
//Disabling HO_LTE_SERVICE_PS_OUT_SWITCH
SET UCORRMALGOSWITCH: HoSwitch=HO_LTE_SERVICE_PS_OUT_SWITCH-0;
This section describes how to activate, verify, and deactivate the optional feature WRFD-140218
Service-Based PS Handover from UMTS to LTE.
Prerequisites
l Dependencies on Hardware
This BSC6900 supports this feature.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The UE must comply with 3GPP Release 8 or later and support UMTS-to-LTE PS
handovers and LTE measurement.
The eNodeB and MME must support UMTS-to-LTE PS handovers.
The SGSN must support UMTS-to-LTE PS handovers.
Context
With this feature, the operator can choose to hand over the high-speed PS services from the
UMTS network to the LTE network. In this way, user experience is improved, and the network
resources of UMTS and LTE are fully utilized.
l Precautions
None
l Data Preparation
Procedure
l Activation Procedure
1. Run the BSC6900 MML command MOD ULTECELL (CME single configuration:
Object Group > UMTS Service Configuration and Maintenance Management >
External Cell Configuration > RNC LTE External Cell; CME batch modification
center: not supported) to set an LTE cell. In this step, set LTE Cell Supporting PS
HO Indicator to Support(Support) and set BlackCell List Flag to False.
2. Run the BSC6900 MML command SET UU2LTEHONCOV (CME single
configuration: UMTS Radio Global Configuration Express > HandOver
Parameter Configuration > RNC-Oriented Non-Coverage-Based UMTS-LTE
Handover Measurement Algorithm Parameters; CME batch modification center:
not supported) to set the RNC-level non-coverage-based UMTS-to-LTE handover
measurement parameters. These parameter settings are to be delivered in the
measurement control information by the BSC6900 to UEs.
3. Optional: Run the BSC6900 MML command ADD UCELLU2LTEHONCOV
(CME single configuration: UMTS Cell Configuration Express > Cell
Parameters > Cell-Oriented Non-Coverage-Based UMTS-LTE Handover
Measurement Algorithm Parameters; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches) to set the cell-level non-coverage-
based UMTS-to-LTE handover measurement parameters for a cell.
4. Run the BSC6900 MML command MOD UTYPRABBASIC (CME single
configuration: UMTS Radio Global Configuration Express > Typical Service
Configuration > Basic Information for Typical Traffic Radio Access Bearer;
CME batch modification center: not supported) to allow the UMTS-to-LTE PS
handovers. In this step, set Service-Based Handover to LTE Allowed to
HO_TO_EUTRAN_SHOULD_BE_PERFORM.
Example
//Activating Service-Based PS Handover from UMTS to LTE
//Configuring an LTE cell
MOD ULTECELL: LTECellIndex=1, SuppPSHOFlag=Support, BlackFlag=False;
//Setting the RNC-level non-coverage-based UMTS-to-LTE handover
measurement parameters
SET UU2LTEHONCOV: LTEMeasTypOf3C=MeasurementQuantity, U2LTEFilterCoef=D6,
U2LTEMeasTime=30, LTEMeasQuanOf3C=RSRP, Hystfor3C=2, TrigTime3C=D10,
TargetRatThdRSRP=20, TargetRatThdRSRQ=30;
//Setting the cell-level non-coverage-based UMTS-to-LTE handover
measurement parameters
ADD UCELLU2LTEHONCOV: CellId=1, LTEMeasTypOf3C=MeasurementQuantity,
U2LTEFilterCoef=D6, U2LTEMeasTime=30, LTEMeasQuanOf3C=RSRP, Hystfor3C=2,
TrigTime3C=D10, TargetRatThdRSRP=20, TargetRatThdRSRQ=30;
//Modifying the basic information about RAB of the typical service
MOD UTYPRABBASIC: RabIndex=1, EUTRANSHIND=HO_TO_EUTRAN_SHOULD_BE_PERFORM;
//Enabling the service-based UMTS-to-LTE PS handovers
SET UCORRMALGOSWITCH:
HoSwitch=HO_LTE_PS_OUT_SWITCH-1&HO_LTE_SERVICE_PSHO_OUT_SWITCH-1;
//Deactivating Service-Based PS Handover from UMTS to LTE
///Disabling the service-based UMTS-to-LTE PS handovers
SET UCORRMALGOSWITCH: HoSwitch=HO_LTE_SERVICE_PSHO_OUT_SWITCH-0;
This section describes how to activate, verify, and deactivate the basic feature WRFD-140224
fast CS fallback based on RIM. For details about how to configure this feature on the LTE side,
see the related documents provided by the LTE equipment vendor.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The UE must support flash CSFB in Release 9.
The mobility management entity (MME) and serving GPRS support node (SGSN) must
support the RIM procedure in 3GPP release 9. If the core network (CN) is earlier than
3GPP release 9, it must support eNodeB ID conversion.
Context
This feature enables the eNodeB to obtain and maintain the system information of the UMTS
cell, including the ID of the target cell and convolutional code, through the RAN Information
Management (RIM) procedure and sends the information to the UE in the RRC Connection
Release message. This can reduce the access time when the UE is redirected from an LTE
network to a UMTS network without reading system information, improving user experience.
l Precautions
None
l Data Preparation
Procedure
l Activation Procedure
1. Configure the data on the LTE side, including setting the neighbor relationships
between cells.
For details about how to configure this feature on the LTE side, see the related
documents provided by the LTE equipment vendor. If the LTE equipment is provided
by Huawei, see the LTE document CS Fallback Parameter Description.
2. Run the BSC6900 MML command SET URRCTRLSWITCH (CME single
configuration: UMTS Radio Global Configuration Express > Process Switch
Configuration > Process Switch; CME batch modification center: 3.15 Modifying
RNC Parameters in Batches). In this step, select
FAST_CS_FB_BASEDON_RIM_SWITCH under Process Control Switch 2 to
enable this feature.
l Verification Procedure
1. Trace the Iu-interface and UE signaling on the RNC LMT. Trace the S1 interface
signaling (on the eNodeB LMT for Huawei eNodeBs) and the UE signaling (on the
M2000 for Huawei eNodeBs).
2. Verify that the Direct Information Transfer message that contains RAN-
INFORMATION PDU REQUEST or RAN-INFORMATION PDU REPORT is
transmitted over the Iu and S1 interfaces.
3. Initiate a CS service in an LTE cell. Check the UE signaling and verify that the IE
CellInfoListUTRA-FDD-r9 in the RRC Connection Release message contains the
frequency, primary scrambling code, and system information (including MIB, SIB1,
SIB3, SIB5, and SIB7) of the target UMTS cell.
4. Check the UE log and measure the duration between the UE receiving an RRC
Connection Release from the eNodeB and the UE sending an RRC Connection
Request to the target UMTS cell. Verify that during this duration the UE does not read
the system information of the target UMTS cell, and that this duration is shorter than
the duration measured when Fast CS Fallback Based on RIM is disabled.
5. Check the UE signaling and verify that the RNC sends the UE an RRC_RB_SETUP
message that contains the IE rrc-StateIndicator and instructs the UE to move to the
CELL_DCH state.
l Deactivation Procedure
1. Run the BSC6900 MML command SET URRCTRLSWITCH (CME single
configuration: UMTS Radio Global Configuration Express > Process Switch
Configuration > Process Switch; CME batch modification center: 3.15 Modifying
RNC Parameters in Batches). In this step, clear
Example
//Activating fast CS fallback based on RIM
SET URRCTRLSWITCH: PROCESSSWITCH2=FAST_CS_FB_BASEDON_RIM_SWITCH-0;
//Deactivating fast CS fallback based on RIM
SET URRCTRLSWITCH: PROCESSSWITCH2=FAST_CS_FB_BASEDON_RIM_SWITCH-1;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010505
Queuing and Preemption.
Prerequisites
l Dependencies on Hardware
This feature requires the CN to bring the information element allocation/retention
priority (ARP) to BSC6900 during RAB assignment so that BSC6900 can obtain service
priorities with RAB parameters.
l Dependencies on Other Features
The following features must be configured before this feature is activated:
WRFD-010610 HSDPA Introduction Package and WRFD-010612 HSUPA
Introduction Package.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others
This feature need the CN bring the ARP IE to RNC during RAB assignment procedure
so that RNC can get the service priority with those RAB parameters.
Context
This feature supports queuing and preemption to implement service differentiation in congested
networks, providing better service for high-priority users.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UQUEUEPREEMPT (CME single
configuration: UMTS Radio Global Configuration Express > Queue Preempt
Parameters Configuration > RNC Oriented Queue Preempt Algorithm
Parameters; CME batch modification center: 3.15 Modifying RNC Parameters in
Batches) to turn on the queuing and preemption switches. In this step, set Preempt
algorithm switch to ON and set Queue algorithm switch to ON.
l Verification Procedure
1. Run the BSC6900 MML command LST UQUEUEPREEMPT to check whether the
queuing and preemption switches are turned on.
l Deactivation Procedure
1. Run the BSC6900 MML command SET UQUEUEPREEMPT (CME single
configuration: UMTS Radio Global Configuration Express > Queue Preempt
Parameters Configuration > RNC Oriented Queue Preempt Algorithm
Parameters; CME batch modification center: 3.15 Modifying RNC Parameters in
Batches) to turn off the queuing and preemption switches. In this step, set Preempt
algorithm switch to OFF and set Queue algorithm switch to OFF.
----End
Example
//Activating Queuing and Preemption
SET UQUEUEPREEMPT: PreemptAlgoSwitch=ON, QueueAlgoSwitch=ON;
//Deactivating Queuing and Preemption
SET UQUEUEPREEMPT: PreemptAlgoSwitch=OFF, QueueAlgoSwitch=OFF;
This section describes how to activate, verify, and deactivate the optional feature WRFD-021103
Access Class Restriction.
Prerequisites
l Dependencies on Hardware
BSC6900 supports NACC RAN Information Management (RIM) and PS handover.
The UE supports NACC and PS handover.
The CN SGSN supports NACC and PS handover.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
When the cell or system is overloaded, this feature can restrict user access based on the allowed
service class by broadcasting system information, controlling potential load requirements of the
system.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UACALGO (CME single configuration:
UMTS Radio Global Configuration Express > Access Restriction Algorithm
Parameters Configuration > AC Algorithm Parameters; CME batch modification
center: 3.15 Modifying RNC Parameters in Batches). In this step, set AC
Restriction Switch to ON and other parameters to appropriate values.
l Verification Procedure
Verifying Access Class Restriction based on CPU overload
1. Start Uu Interface Trace on the BSC6900 LMT.
2. Run the BSC6900 MML command LST FCCPUTHD to query the settings of
AC control threshold and AC restore threshold.
3. Run the BSC6900 MML command SET FCCPUTHD. In this step, set AC control
threshold and AC restore threshold to appropriate values.
4. Enable a large number of UEs to access a cell until the CPU usage exceeds the AC
restore threshold.
5. Start Uu Interface Trace on the BSC6900 LMT and select
RRC_SYS_INFO_TYPE3 as the message type. If the value of barred IE in the
RRC_SYS_INFO_TYPE3 message is 0, as shown in Figure 284-1, the feature
has been activated. If the value is not 0, the feature is not activated.
6. Reduce the number of UEs in the cell until the CPU usage is lower than the AC
restore threshold.
7. Run the BSC6900 MML command SET FCCPUTHD. In this step, set AC control
threshold and AC restore threshold to their original values.
Verifying Access Class Restriction based on the access failure on the Iu interface
1. Run the BSC6900 MML command SET URRCTRLSWITCH. In this step, set
Process switch to SYS_INFO_UPDATE_FOR_IU_RST and
BARRED_CELL_FOR_CSDOMAIN_RST.
2. Run the BSC6900 MML commandMOD UCELLALGOSWITCH. In this step,
set Cell CAC algorithm switch to SYS_INFO_UPDATE_FOR_IU_RST
(System Info Update Switch for Iu Reset).
4. Run the BSC6900 MML command RST UIU. In this step, set CN Domain ID to
CS_DOMAIN.
5. Start Uu Interface Trace on the BSC6900 LMT and select
RRC_SYS_INFO_TYPE3 as the message to be traced. If the traced
RRC_SYS_INFO_TYPE3 message indicates that the cell is barred, as shown in
Figure 284-2, the feature has been activated. If the traced message does not
indicate that the cell is barred, the feature is not activated.
l Deactivation Procedure
1. Run the BSC6900 MML command SET UACALGO (CME single configuration:
UMTS Radio Global Configuration Express > Access Restriction Algorithm
Parameters Configuration > AC Algorithm Parameters; CME batch modification
center: 3.15 Modifying RNC Parameters in Batches). In this step, set AC
Restriction Switch to OFF.
----End
Example
//Activating Access Class Restriction
SET UACALGO: AcRstrctSwitch=ON, AcRstrctPercent=5, AcIntervalOfCell=1,
AcRstrctIntervalLen=6;
This section describes how to activate, verify, and deactivate the optional feature WRFD-050424
Traffic Priority Mapping onto Transmission Resources.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature enables the dynamical mapping of the services onto the transport bearers according
to the TC, ARP, and THP of the user. Operators can flexibly configure the mapping to provide
differentiated services while guaranteeing the QoS.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command ADD TRMMAP (CME single configuration:
UMTS Global Configuration Express > Transmission Resources Configuration
> Transport Resource Mapping; CME batch modification center: not supported) to
add the transport resource mapping.
NOTE
l Before setting the type of a mapping path for a service, ensure that this type of path is
available. Otherwise, the service may fail to be set up.
l The primary path and the secondary path for the same service type must be different.
l The default 14 transport resource mappings (indexed from 0 to 13) are added when the
system is initialized, and you cannot modify them.
2. Run the BSC6900 MML command ADD ADJMAP (CME single configuration:
NodeB Configuration Express > IUB_RNC > IP Transport > Adjacent Node
Mapping; CME batch modification center: not supported) to add the TRM mapping
to the adjacent node.
NOTE
Before running this command, ensure that the adjacent node or the NodeB is added by running
the BSC6900 MML command ADD ADJNODE (CME single configuration: NodeB
Configuration Express > IUB_RNC > IP Transport > Adjacent Node; CME batch
modification center: not supported) or ADD UNODEB (CME single configuration: Main
View > Right Click RNC > Create Logical NodeB; CME batch modification center: not
supported).
l Verification Procedure
This feature can be verified only by running the LST commands.
1. Run the BSC6900 MML command LST TRMMAP to check whether the transport
resource mapping is correct.
2. If the mapping is incorrect, run the BSC6900 MML command MOD TRMMAP to
modify the mapping.
NOTE
Do not modify Interface Type and Transport Type in the MOD TRMMAP command.
l Deactivation Procedure
1. Run the BSC6900 MML command RMV ADJMAP (CME single configuration:
NodeB Configuration Express > IUB_RNC > IP Transport > Adjacent Node
Mapping; CME batch modification center: not supported) to remove the TRM
mapping to the adjacent node.
2. Run the BSC6900 MML command RMV TRMMAP (CME single configuration:
UMTS Global Configuration Express > Transmission Resources Configuration
> Transport Resource Mapping; CME batch modification center: not supported) to
remove the transport resource mapping.
----End
Example
//Activating Traffic Priority Mapping onto Transmission Resources
ADD TRMMAP: TMI=15, REMARK="15", ITFT=IUB, TRANST=IP, VOICEPRIPATH=AF11;
ADD ADJMAP: ANI=10, ITFT=IUB, TRANST=IP, CNMNGMODE=SHARE, TMIGLD=15,
TMISLV=15, TMIBRZ=15, FTI=13;
This section describes how to activate, verify, and deactivate the optional feature WRFD-020806
Differentiated Service Based on SPI Weight.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The following features have been configured before this feature is activated:
WRFD-01061103 Scheduling based on EPF and GBR has been configured before
this feature is applied in the downlink over the Uu interface.
WRFD-01061402 Enhanced Fast UL Scheduling or WRFD-010638 Dynamic CE
Resource Management has been configured before this feature is applied in the
uplink over the Uu interface. When this feature is enabled together with the optional
feature WRFD-01061402 Enhanced Fast UL Scheduling, only uplink Uu interface
resources can be differentially scheduled. When this feature is enabled together with
the optional feature RFD-010638 Dynamic CE Resource Management, both uplink
Uu interface resources and CE resources can be differentially scheduled.
WRFD-010610 HSDPA Introduction Package and WRFD-050405 Overbooking on
ATM Transmission, or WRFD-010610 HSDPA Introduction Package and
WRFD-050408 Overbooking on IP Transmission have been configured before this
feature is applied in the downlink over the Iub interface.
WRFD-010637 HSUPA Iub Flow Control in Case of Iub Congestion has been
configured before this feature is applied in the uplink over the Iub interface.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
When Uu interface resources, CE resources, and Iub transmission resources do not meet the
GBR requirements of all online users, this feature enables the RAN to preferentially guarantee
the GBR of high-priority users. The RAN can thereby provide differentiated services under a
certain level of fairness.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UUSERPRIORITY (CME single
configuration: UMTS Radio Global Configuration Express > User Integrated
Priority Parameters Configuration > RNC Oriented User Priority Related
Parameters; CME batch modification center: 3.15 Modifying RNC Parameters in
Batches) to configure gold, silver, and copper users.
2. Run the BSC6900 MML command SET UTHPCLASS (CME single configuration:
UMTS Radio Global Configuration Express > Channel Management
Configuration > THP Class for Interactive Users; CME batch modification center:
3.15 Modifying RNC Parameters in Batches) to set priorities of PS interactive
services to appropriate values.
3. Run the BSC6900 MML command SET USCHEDULEPRIOMAP (CME single
configuration: UMTS Radio Global Configuration Express > Channel
Management Configuration > Schedule Priority Map Information; CME batch
modification center: not supported) to set the scheduling priority mapping
information.
4. Run the BSC6900 MML command SET UCAPARATERANGE (CME single
configuration: UMTS Radio Global Configuration Express > Channel
Management Configuration > Rate Thresholds for Differentiated HSPA Services
Based on SPI Weight; CME batch modification center: not supported) to set RNC-
specific reference rates and rate thresholds of all levels in the uplink and downlink.
5. Optional: Run the BSC6900 MML command ADD
UOPERCAPARATERANGE (CME single configuration: UMTS Radio Global
Configuration Express > Channel Management Configuration > Operator-Level
Rate Thresholds for SPI Weight of HSPA Services; CME batch modification
center: not supported) to set operator-specific reference rates and rate thresholds of
all levels in the uplink and downlink.
6. Run the BSC6900 MML command SET USPIWEIGHT (CME single configuration:
UMTS Radio Global Configuration Express > Channel Management
Configuration > Factor of Schedule Priority; CME batch modification center: 3.15
Modifying RNC Parameters in Batches) to set RNC-specific scheduling priority
weight.
7. Optional: Run the BSC6900 MML command ADD UOPERSPIWEIGHT (CME
single configuration: UMTS Radio Global Configuration Express > Channel
Management Configuration > Operator-Oriented Factor of Schedule Priority;
CME batch modification center: not supported) to set operator-specific scheduling
priority weight.
8. Run the BSC6900 MML command SET URRCTRLSWITCH (CME single
configuration: UMTS Radio Global Configuration Express > Process Switch
Configuration > Process Switch; CME batch modification center: 3.15 Modifying
RNC Parameters in Batches). In this step, set Process switch to
NODEB_PRIVATE_INTERFACE_SWITCH.
l Verification Procedure
1. Establish services on UE A and UE B. Assume that the SPI and SPI weight of UE A
are 7 and 50 respectively and the SPI and SPI weight of UE B are 7 and 100
respectively. In the traced Iub interface messages, check the information element (IE)
schedulingPriorityIndicator in the NBAP_RL_RECFG_PREP message to obtain
the SPI value; check the IE schedule-Prior-Indication-Weight-Private to obtain the
SPI weight, which is the actual SPI value for the NodeB, as shown in Figure 286-1,
Figure 286-2, Figure 286-3, and Figure 286-4.
Example
/*Activating Differentiated Service Based on SPI Weight*/
This section describes how to activate, verify, and deactivate the optional feature WRFD-020131
Optimization of R99 and HSUPA Users Fairness.
Prerequisites
l Dependencies on Hardware
The HBBI and HULP boards in the BTS3812E/BTS3812AE do not support this feature.
To support this feature, the BTS3812E/BTS3812AE must be configured with the EBBI
or EDLP board.
The BBU3806 in the DBS3800 does not support this feature. To support this feature,
the DBS3800 must be configured with the EBBC or EBBCd board.
To support this feature, the 3900 series base stations must be configured with WBBPb
or WBBPd boards. WBBPa boards in the 3900 series base stations do not support this
feature.
l Dependencies on Other Features
The feature WRFD-010612 HSUPA Introduction Package must be configured before
this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
In scenarios where R99 and HUSUPA users share the same TRX, this feature provides fair
services for the two types of users and improves HSUPA user experience by considering R99
and HSUPA user satisfaction with throughput, that is, the ratio of effective rate to guaranteed
bit rate (GBR).
Procedure
l Activation Procedure
1. To enable the algorithm switch for cell-level rate reduction for BE services based on
R99 and HSUPA user fairness, run the BSC6900 MML command MOD
l Deactivation Procedure
1. To disable the algorithm switch for cell-level rate reduction for BE services based on
R99 and HSUPA user fairness, run the BSC6900 MML command MOD
UCELLALGOSWITCH (CME single configuration: UMTS Cell Configuration
Express > Cell Parameters > Cell Algorithm Switches; CME batch modification
center: 3.18 Modifying UMTS Cell Parameters in Batches) with BE rate reduction
switch based on fairness set to OFF(Algorithm is OFF).
----End
Example
/*Activating the Optimization of R99 and HSUPA Users Fairness feature
//Setting the common measurement period based on R99 and HSUPA user
fairness
SET ULDCPERIOD: FairnessPeriodTimerLen=11;
//Setting the common measurement period based on R99 and HSUPA user
fairness in a satellite communications environment
SET USATLDCPERIOD: FairnessPeriodTimerLen=11;
This section describes how to activate, verify, and deactivate the optional feature WRFD-011502
Active Queue Management (AQM).
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
The AQM feature can improve user's feeling when HTTP and download services simultaneously
exist.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) to turn on the RNC-level AQM switch. In this step, select
the Dynamic resource allocation switch check box under the parameter
DRA_AQM_SWITCH.
l Verification Procedure
1. Initiate UE tracing on the BSC6900 LMT. In the displayed UE Trace dialog box,
select the Debug Mode check box, as shown in Figure 288-1.
2. Establish a BE service on the UE. Verify the value of the information element (IE)
"ucAqmSwitch" contained in the message PdcpSetupInfo as follows:
If the value of the IE "ucAqmSwitch" is 1, this feature has been activated.
If the value of the IE "ucAqmSwitch" is 0, this feature is not activated.
l Deactivation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, deselect the DRA_AQM_SWITCH check box
under the parameter Dynamic resource allocation switch.
----End
Example
//Activating Active Queue Management (AQM)
SET UCORRMALGOSWITCH: DraSwitch=DRA_AQM_SWITCH-1;
//Deactivating Active Queue Management (AQM)
SET UCORRMALGOSWITCH: DraSwitch=DRA_AQM_SWITCH-0;
This section describes how to activate, verify, and deactivate the optional feature WRFD-020128
Quality Improvement for Subscribed Service.
Prerequisites
l Dependencies on Hardware
Only BSC6900 supports this feature.
For BTS3812E and BTS3812AE, EBBI, EBOI, EULP or EULPd board is needed.
For BBU3806, EBBC/EBBCd is needed.
For BBU3900, WBBPb or WBBPd is needed.
l Dependencies on Other Features
The feature WRFD-010610 HSDPA Introduction Package has been configured before
this feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others
None.
Context
This feature enables BSC6900 to adjust the user scheduling priority by identifying the
characteristics of IP data streams and modifying the initial Scheduling Priority Indicator (SPI)
Weight of downlink services.
The feature grants high scheduling priorities to specific services on which telecom operators
focus, such as services from specific servers or http services. By doing this, the bandwidth
required for processing the services is guaranteed.
In addition, the feature lowers the scheduling weight of some non-paying services that consume
a large amount of bandwidth. By doing this, sufficient bandwidth is available for services with
high scheduling priorities.
Procedure
l Activation Procedure
1. Set the initial SPI Weight on the BSC6900 LMT.
If the license controlling the feature WRFD-020806 Differentiated Service Based
on SPI Weight has been activated, run the BSC6900 MML command SET
USPIWEIGHT (CME single configuration: UMTS Radio Global
Configuration Express > Channel Management Configuration > Factor of
Schedule Priority; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, set the parameters Scheduling Priority
Indicator and SPI Weight based on the actual network plan.
If the license controlling the feature WRFD-020806 Differentiated Service Based
on SPI Weight is not activated, run the BSC6900 MML command SET UFRC
(CME single configuration: UMTS Radio Global Configuration Express >
Basic Resource Control Parameter Configuration > RNC Oriented FRC
Algorithm Parameters; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, set Default SPI Weight based on the actual
network plan.
2. Run the BSC6900 MML command SET URRCTRLSWITCH (CME single
configuration: UMTS Radio Global Configuration Express > Process Switch
Configuration > Process Switch; CME batch modification center: 3.15 Modifying
RNC Parameters in Batches). In this step, select the
NODEB_PRIVATE_INTERFACE_SWITCH check box under the parameter
Process switch.
3. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, select the
DRA_IP_SERVICE_QOS_SWITCH check box under the parameter Dynamic
Resource Allocation Switch.
4. Run the BSC6900 MML command ADD UIPSERVICEQOS (CME single
configuration: UMTS Global Configuration Express > Operator Configuration >
Simple Packet Identify Three Element Parameter; CME batch modification center:
not supported). In this step, set the parameters related to the Quality Improvement for
Subscribed Service feature to appropriate values based on the network plan.
5. Run the BSC6900 MML command SET UDPUCFGDATA (CME single
configuration: UMTS Radio Global Configuration Express > DPU Data
Configuration > DPU Configuration Parameters; CME batch modification center:
3.15 Modifying RNC Parameters in Batches). In this step, set Service Priority
Adjusting Coefficient to an appropriate value.
l Verification Procedure
1. When the resources (for example, resources on the air interface) are limited, activating
this feature may increase the throughput of FTP services and shorten the network delay
of HTTP services.
l Deactivation Procedure
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Example
//Activating Quality Improvement for Subscribed Service
//Setting the initial SPI weight value if the license control switch for
the feature WRFD-020806 Differentiated Service Based on SPI Weight is
turned on
SET USPIWEIGHT: SPI=4, SPIWEIGHT=10;
//Setting the initial SPI weight value if the license control switch for
the feature WRFD-020806 Differentiated Service Based on SPI Weight is not
turned on
SET UFRC: DefaultSPIWeight=10;
This section describes how to activate, verify, and deactivate the optional feature WRFD-020123
TCP Accelerator.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The TCP Accelerator feature takes effect only when the server has the Time Stamp
option in the TCP deselected.
Downlink TCP accelerator requires that the BSC6900 version is RAN11.0 or later.
Uplink TCP accelerator requires that the BSC6900 version is RAN12.0 or later.
Context
The TCP Accelerator feature in RAN11.0 optimizes the data transmission performance in the
downlink.
Based on this feature in RAN11.0, RAN12.0 introduces the TCP Accelerator feature to optimize
the data transmission in the uplink. In addition, the Acknowledgment (ACK) splitting
technology, ACK splitting monitoring technology, and uplink data packet sequencing
technology are adopted. These technologies aim at accelerating the slow start and restore
processes during uplink data transmission, reducing the impact of packet loss on the performance
of uplink TCP data transmission.
NOTE
Data configurations are required only at the BSC6900 to activate, verify, and deactivate this feature.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET UDPUCFGDATA (CME single
configuration: UMTS Radio Global Configuration Express > DPU Data
Configuration > DPU Configuration Parameters; CME batch modification center:
3.15 Modifying RNC Parameters in Batches) to turn on the TCP accelerator switch.
In this step, select TPE_DOWNLINK_SWITCH or TPE_UPLINK_SWITCH
from TPE switch according to the actual requirements.
l Verification Procedure
1. Run the BSC6900 MML command LST UDPUCFGDATA to check whether the
TCP accelerator switch is turned on. If the switch is turned on, this feature has been
activated.
2. Use a test terminal to download a file of 200 KB from the FTP server. Then, compare
the download time taken before and after the TPE_DOWNLINK_SWITCH is turned
on.
3. Use a test terminal to upload a file of 200 KB to the FTP server. Then, compare the
upload time taken before and after the TPE_UPLINK_SWITCH is turned on.
l Deactivation Procedure
1. Run the BSC6900 MML command SET UDPUCFGDATA (CME single
configuration: UMTS Radio Global Configuration Express > DPU Data
Configuration > DPU Configuration Parameters; CME batch modification center:
3.15 Modifying RNC Parameters in Batches) to turn off the TCP accelerator switch.
In this step, deselect TPE_DOWNLINK_SWITCH or TPE_UPLINK_SWITCH
from TPE switch according to the actual requirements.
----End
Example
//Activating TCP Accelerator
Turning on the TCP accelerator switch at the RNC
SET UDPUCFGDATA: TpeSwitch=TPE_DOWNLINK_SWITCH-1&TPE_UPLINK_SWITCH-1;
//Deactivating TCP Accelerator
Turning off the TCP accelerator switch at the RNC
SET UDPUCFGDATA: TpeSwitch=TPE_DOWNLINK_SWITCH-0&TPE_UPLINK_SWITCH-0;
This section describes how to activate, verify, and deactivate the optional feature WRFD-010507
Rate Negotiation at Admission Control.
Prerequisites
l Dependencies on Hardware
This feature does not depend on the hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
For Iu QoS negotiation, the CN nodes must support this feature.
For RAB rate reduction, the CN nodes do not need to support this feature.
Context
This feature supports the procedures for Iu QoS negotiation and RAB rate reduction.
Procedure
l Activation Procedure
Activating QoS negotiation
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME
single configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, set Dynamic Resource Allocation
Switch to DRA_DCCC_SWITCH, and set PS rate negotiation switch to
PS_BE_IU_QOS_NEG_SWITCH and
PS_STREAM_IU_QOS_NEG_SWITCH.
Activating RAB rate reduction
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME
single configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, set Dynamic Resource Allocation
Switch to DRA_DCCC_SWITCH, and set PS rate negotiation switch to
PS_RAB_DOWNSIZING_SWITCH.
l Verification Procedure
Verifying QoS negotiation
1. Run the BSC6900 MML command LST UCORRMALGOSWITCH to query
the activation result.
2. Start Iu message tracing on the BSC6900 LMT and establish a PS service, as shown
in Figure 291-1.
l Deactivation Procedure
Deactivating QoS negotiation
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME
single configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, deselect DRA_DCCC_SWITCH from the
Dynamic Resource Allocation Switch drop-down list box, and deselect
PS_BE_IU_QOS_NEG_SWITCH and
PS_STREAM_IU_QOS_NEG_SWITCH from the PS rate negotiation
switch drop-down list box.
Deactivating RAB rate reduction
1. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME
single configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, deselect DRA_DCCC_SWITCH from the
Dynamic Resource Allocation Switch drop-down list box, and deselect
PS_RAB_DOWNSIZING_SWITCH from the PS rate negotiation switch drop-
down list box.
----End
Example
//Activating Rate Negotiation at Admission Control
SET UCORRMALGOSWITCH: DraSwitch=DRA_HSUPA_DCCC_SWITCH-1, PsSwitch
=PS_BE_IU_QOS_NEG_SWITCH-1&PS_STREAM_IU_QOS_NEG_SWITCH-1;
SET UCORRMALGOSWITCH: DraSwitch=DRA_HSUPA_DCCC_SWITCH-1,
PsSwitch=PS_RAB_DOWNSIZING_SWITCH-1;
This section describes how to activate, verify, and deactivate the optional feature WRFD-020130
Videophone Service Restriction.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature disables the videophone (VP) function of a cell through cell-level configurations to
meet telecom operators' requirements for information security in restricted areas.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command DEA UCELL (CME single configuration: UMTS
Cell Configuration Express > Cell Basic Information > Cell Basic Information.
Set Validation indication to Deactivated; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches) to deactivate the cell. In this step,
set Cell ID to an appropriate value.
2. Run the BSC6900 MML command MOD UCELLSETUP (CME single
configuration: UMTS Cell Configuration Express > Cell Basic Information > Cell
Basic Information; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches). In this step, set Cell VP Limit Indicator to TRUE.
3. Run the BSC6900 MML command ACT UCELL (CME single configuration: UMTS
Cell Configuration Express > Cell Basic Information > Cell Basic Information.
----End
Example
//Activating Videophone Service Restriction
This section describes how to activate, verify, and deactivate the optional feature WRFD-020135
Intelligent Inter-Carrier UE Layered Management.
Prerequisites
l Dependencies on Hardware
This feature does not have any special requirements for hardware.
l Dependencies on Other Features
The feature WRFD-020400 DRD Introduction Package must be configured before this
feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature allows the RAN to intelligently distinguish between UEs and data cards in multi-
carrier scenarios and to separately set up services on different carriers.
Procedure
l Activation Procedure
The following methods assume that cell F1 and cell F2 are used.
1. Run the BSC6900 MML command SET UDRD (CME single configuration: UMTS
Radio Global Configuration Express > Directed Retry Parameter
Configuration > RNC-Oriented DRD Algorithm Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches). In this step, set
Device Type Steering DRD Switch to ON.
2. Run the BSC6900 MML command ADD UCELLLICENSE (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
License Resource/Function Item; CME batch modification center: 3.18 Modifying
UMTS Cell Parameters in Batches) twice to enable the layered terminal
management function for cell F1 and cell F2 respectively. In this step, set
FuncSwitch1 to INTELLIGENT_INTERFREQ_UE_TYPE_STEERING.
3. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME single
configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches). In this step, set Direct Retry Switch to
DR_RAB_SING_DRD_SWITCH.
4. Run the BSC6900 MML command ADD UDEVICETYPEIMSI (CME single
configuration: UMTS Radio Global Configuration Express > Directed Retry
Parameter Configuration > IMSI segment; CME batch modification center: not
supported). In this step, set IMSI Segment Choice to MultiIMSI and specify the
IMSI number range by setting IMSI Segment Start Value and IMSI Segment End
Value. If the IMSI of a terminal falls into the IMSI number range, the terminal is
regarded as a data card.
5. Run the BSC6900 MML command ADD UDEVICETYPEPRIOGROUP (CME
single configuration: UMTS Radio Global Configuration Express > Directed
Retry Parameter Configuration > Device Type Steering Priority Group; CME
batch modification center: not supported) to add terminal type priorities.
6. Run the BSC6900 MML command MOD UCELL (CME single configuration:
UMTS Cell Configuration Express > Cell Basic Information > Cell Basic
Information; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches) twice to bind a terminal type priority to cell F1 and cell F2
respectively.
7. Optional: Configure preferred camping. Cell F1 is a preferred camping frequency,
and cell F2 is a services balancing frequency.
NOTE
This feature does not depend on the camping policy setting of an existing network. When this
feature is activated and cell F2 provides discontinuous coverage, you must configure inter-
frequency neighboring cells for cell F2 during network optimization so that this feature can be
enabled.
Method 1
a. Run the BSC6900 MML command MOD UCELLSELRESEL (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters >
Cell Selection And Reselection; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches) to make it difficult for UEs
in idle mode to trigger inter-frequency measurement. In this step, set Inter-
freq cell reselection threshold for idle mode of cell F1 to 0.
b. Run the BSC6900 MML command MOD UCELLSELRESEL (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters >
Cell Selection And Reselection; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches) to make UEs in idle mode
keep triggering inter-frequency measurement. In this step, set Inter-freq cell
reselection threshold for idle mode of cell F2 to 127.
c. Run the BSC6900 MML command MOD UINTERFREQNCELL (CME
single configuration: UMTS Cell Configuration Express > Neighboring
Cell > Inter-frequency Neighboring Cell; CME batch modification center:
not supported) to set inter-frequency neighboring cell parameters (cell F1 to
cell F2).
l Deactivation Procedure
1. Run the BSC6900 MML command SET UDRD (CME single configuration: UMTS
Radio Global Configuration Express > Directed Retry Parameter
Configuration > RNC-Oriented DRD Algorithm Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches). In this step, set
Device Type Steering DRD Switch to OFF.
2. Run the BSC6900 MML command RMV UCELLLICENSE (CME single
configuration: UMTS Cell Configuration Express > Cell Parameters > Cell
License Resource/Function Item; CME batch modification center: not supported)
to disable the layered terminal management function for the cell.
----End
Example
//Activating Intelligent Inter-Carrier UE Layered Management
//Turning on the layered terminal management switch
SET UDRD: DPGDRDSwitch=ON;
//Enabling the layered terminal management function for cell F1 and cell
F2
ADD UCELLLICENSE: CellId=11013, INTELLIGENT_INTERFREQ_UE_TYPE_STEERING-1;
ADD UCELLLICENSE: CellId=11014, INTELLIGENT_INTERFREQ_UE_TYPE_STEERING-1;
//Turning on the single-service DRD switch
SET UCORRMALGOSWITCH: DrSwitch=DR_RAB_SING_DRD_SWITCH-1;
//Configuring an IMSI number range
ADD UDEVICETYPEIMSI: IMSISegIndex=1, IMSISegChoice=MultiIMSI,
IMSIStart="502808888800070", IMSIEnd="502808888800080";
//Adding terminal type priorities
ADD UDEVICETYPEPRIOGROUP: DPGId=1, UEDP=1, DataCardDP=1, ReservedDP=1;
ADD UDEVICETYPEPRIOGROUP: DPGId=2, UEDP=2, DataCardDP=2, ReservedDP=1;
//Binding terminal type priorities to cells
MOD UCELL: CellId=11013, DPGId=1;
MOD UCELL: CellId=11014, DPGId=2;
This section describes how to activate, verify, and deactivate the optional feature WRFD-140219
Micro NodeB Self-Planning.
Prerequisites
l Dependencies on Hardware
Only the BTS3902E supports this feature.
The BTS3902E has been configured with the SON receiver (default configuration) and
antenna.
If the BTS3902E uses an integrated antenna, the integrated antenna incorporates the
function of the SON receiver antenna and therefore a SON receiver antenna does
not need to be configured.
If the BTS3902E uses an external antenna, a SON receiver antenna needs to be
configured.
The RNC version must be RAN13.0 or later, and the RNC data can be configured and
modified on the M2000.
l Dependencies on Other Features
The feature WRFD-031101 NodeB Self-discovery Based on IP Mode and
WRFD-031102 NodeB Remote Self-configuration must be configured before this
feature is activated.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others
Data has been configured for micro NodeBs on the RNC side. The UARFCN,
scrambling code, LAC, RAC, and SAC do not need to be planned, but they must have
initial values in the data configuration file. The initial SAC value is configured in the
core network.
OM channels have been established for micro NodeBs, and micro NodeBs have
obtained their configuration files from the M2000. The UARFCN does not need to be
planned, but it must have an initial value in the data configuration file.
Necessary information has been obtained for SON receiver parameter settings.
The NodeB auto deployment function is enabled on the M2000 side.
The M2000 must support BTS3902E WCDMA self-planning.
The RNC version must be RAN13.0 or later, and the RNC data can be configured and
modified on the M2000.
The GBSC version must be GBSS 14.0 or later to support remote configuration by the
M2000.
Context
l This feature automatically plans the following information for micro NodeBs:
Available UTRA Absolute Radio Frequency Channel Numbers (UARFCNs)
Scrambling codes
Intra-frequency neighboring cells
Inter-frequency neighboring cells
Inter-RAT neighboring cells between UMTS and GSM
LAC/SAC/RAC parameters, in which SAC self-planning results is cell ID.
l Precautions
This feature interrupts micro NodeB services.
In micro NodeB self-planning, ensure that the logical cell on the RNC has been
deactivated when preparing the RNC-side micro NodeB configuration file. The
UARFCN, scrambling code, intra-frequency neighboring cell, inter-frequency
neighboring cell, and neighboring GSM cell, LAC, RAC, and SAC in the logical micro
NodeB configuration file on the RNC are initial values, not optimal values. They may
cause interference to neighboring cells.
l Data Preparation
Preparing Data for SON Receivers
Before enabling this feature, SON receiver parameters must be preconfigured.
SON Receiver Description Source
Parameter
Procedure
l Activation Procedure
Configuring SON Receiver Parameters on the M2000
After necessary data has been collected, perform the following steps on the M2000 to
configure SON receiver parameters.
1. Choose Configuration > UMTS Self-Planning.
2. Click the Receiver Parameter Settings tab.
3. Under the Parameters node, select the data type to be configured.
On the M2000 side, you can suspend a NodeB auto deployment task before the system
proceeds to the self-planning step. Once the self-planning step starts, it cannot be
suspended.
Once a micro NodeB receives a self-planning command, it starts procedures such as SON
receiver scanning and scanning result reporting. You cannot suspend self-planning.
----End
Example
None
This section describes how to activate, verify, and deactivate the optional feature WRFD-140209
NodeB Integrated IPSec.
Prerequisites
l Dependencies on Hardware
Only the 3900 series base stations equipped with the UMPT board support this feature
on Ethernet ports.
l Dependencies on Other Features
This feature depends on the feature WRFD-050402 IP Transmission Introduction on
Iub Interface.
When a digital certificate is used for authentication, this feature depends on the feature
WRFD-140210 NodeB PKI Support.
This feature cannot be used with the Automatic Address Configuration Protocol
(AACP) function in the feature WRFD-031101 NodeB Self-Discovery Based on IP
Route.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
On a UMTS network, an SeGW must be deployed on the RNC side to support IP
Security (IPSec).
Context
l IPSec policies include access control list (ACL) rules, IPSec protocols, and Internet Key
Exchange (IKE).
An ACL consists of a series of ACL rules, which are used to specify the data streams
to be protected. Only data streams that comply with ACL rules can enter an IPSec tunnel.
An IPSec protocol defines how to protect data streams and includes the protocol type,
encapsulation mode, and encryption and verification algorithms.
IKE is used to authenticate IPSec peers, negotiate encryption algorithms, and generate
session keys before an IPSec SA is established. IKE supports two methods for
authenticating IPSec peers: pre-shared key (PSK) and digital certificate.
l During IPSec deployment, base station data can be encrypted in two modes: unified
encryption and separate encryption.
In unified encryption mode, O&M data streams are protected by IPSec. Secure Sockets
Layer (SSL) encryption can be implemented before IPSec encryption.
In separate encryption mode, O&M data streams are protected by SSL, not by IPSec.
l Accordingly, IPSec networking scenarios are classified into the following types:
PKI-based networking in unified encryption mode
PKI-based networking in separate encryption mode
PSK-based networking in unified encryption mode
PSK-based networking in separate encryption mode
l Precautions
IPSec ensures transmission security by encapsulating and encrypting IP packets. This
reduces the transmission efficiency of service packets on the bearer network.
l Data Preparation
Prepare the data required for the IKE proposal (the IKEPROPOSAL MO).
Parameter Name Parameter ID Setting Source
Description
Prepare the data required for the IKE peer (the IKEPEER MO).
Parameter Name Parameter ID Setting Source
Description
Prepare the data required for the ACL rule (the ACL MO).
One or multiple ACLs need to be configured based on the planned IPSec tunnels. In the
IPSECPOLICY MO, an IPSec policy is bound to an ACL based on the ACLID setting.
Only data streams that comply with ACL rules are processed according to the operations
defined in the IPSec policy.
Parameter Name Parameter ID Setting Source
Description
Prepare the data required for the ACL rule (the ACLRULE MO).
Depending on the network plan, an IPSec tunnel may require multiple ACL rules to
protect different types of data streams.
Parameter Name Parameter ID Setting Source
Description
Protocol Type PT -
Destination DWC -
Wildcard
DSCP DSCP -
Prepare the data required for the IPSec proposal (the IPSECPROPOSAL MO).
Prepare the data required for the IPSec policy (the IPSECPOLICY MO).
Parameter Name Parameter ID Setting Source
Description
Prepare the data required for binding an IPSec policy group to a port (the
IPSECBIND MO).
Parameter Name Parameter ID Setting Source
Description
Slot No. SN -
If a PSK is used for authentication, prepare the IKE configuration data (the IKECFG
MO).
Parameter Name Parameter ID Setting Source
Description
Procedure
l Activation Procedure
Scenario 1: PKI-based Networking for a NodeB Using Unified Encryption
Figure 295-1 Example of PKI-based networking for a NodeB using unified encryption
1. Run the NodeB MML command ADD IKEPROPOSAL (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > IKE > IKE Proposal; CME batch modification
center: not supported) to add an IKE proposal.
2. Run the NodeB MML command ADD IKEPEER (CME single configuration: NodeB
Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > IKE > IKE Peer; CME batch modification center:
not supported) to add an IKE peer.
3. Run the NodeB MML command ADD ACL (CME single configuration: NodeB
Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > ACL > Access Control List; CME batch modification
center: not supported) to add an ACL.
4. Run the NodeB MML command ADD ACLRULE (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > Ipsecurity > ACL > Access Control List Rule; CME batch
modification center: not supported) to add a rule to the ACL.
5. Run the NodeB MML command ADD IPSECPROPOSAL (CME single
configuration: NodeB Configuration Express > IUB_NodeB > IP Transport
Layer > Feature Configuration > IPSecurity > IPSec > IPSec Proposal; CME
batch modification center: not supported) to add an IPsec proposal.
6. Run the NodeB MML command ADD IPSECPOLICY (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > IPSec > IPSec Policy; CME batch modification
center: not supported) to add an IPSec policy.
7. Run the NodeB MML command ADD IPSECBIND (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > IPSec > IPSec Policy Group Binding; CME batch
modification center: not supported) to bind an IPSec policy to a port.
Scenario 2: PKI-based Networking for a NodeB Using Separate Encryption
Figure 295-2 Example of PKI-based networking for a NodeB using separate encryption
Configuration > IPSecurity > IKE > IKE Proposal; CME batch modification
center: not supported) to add an IKE proposal.
2. Run the NodeB MML command ADD IKEPEER (CME single configuration: NodeB
Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > IKE > IKE Peer; CME batch modification center:
not supported) to add an IKE peer.
3. Run the NodeB MML command ADD ACL (CME single configuration: NodeB
Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > ACL > Access Control List; CME batch modification
center: not supported) to add an ACL.
4. Run the NodeB MML command ADD ACLRULE (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > Ipsecurity > ACL > Access Control List Rule; CME batch
modification center: not supported) to add a rule to the ACL.
5. Run the NodeB MML command ADD IPSECPROPOSAL (CME single
configuration: NodeB Configuration Express > IUB_NodeB > IP Transport
Layer > Feature Configuration > IPSecurity > IPSec > IPSec Proposal; CME
batch modification center: not supported) to add an IPsec proposal.
6. Run the NodeB MML command ADD IPSECPOLICY (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > IPSec > IPSec Policy; CME batch modification
center: not supported) to add an IPSec policy.
7. Run the NodeB MML command ADD IPSECBIND (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > IPSec > IPSec Policy Group Binding; CME batch
modification center: not supported) to bind an IPSec policy to a port.
Scenario 3: PSK-based Networking for a NodeB Using Unified Encryption
Figure 295-3 Example of PSK-based networking for a NodeB using unified encryption
1. Run the NodeB MML command SET IKECFG (CME single configuration: NodeB
Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > IKE > IKE Basic Configuration; CME batch
modification center: not supported) to set local IKE configurations.
2. Run the NodeB MML command ADD IKEPROPOSAL (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > IKE > IKE Proposal; CME batch modification
center: not supported) to add an IKE proposal.
3. Run the NodeB MML command ADD IKEPEER (CME single configuration: NodeB
Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > IKE > IKE Peer; CME batch modification center:
not supported) to add an IKE peer.
4. Run the NodeB MML command ADD ACL (CME single configuration: NodeB
Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > ACL > Access Control List; CME batch modification
center: not supported) to add an ACL.
5. Run the NodeB MML command ADD ACLRULE (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > Ipsecurity > ACL > Access Control List Rule; CME batch
modification center: not supported) to add a rule to the ACL.
6. Run the NodeB MML command ADD IPSECPROPOSAL (CME single
configuration: NodeB Configuration Express > IUB_NodeB > IP Transport
Layer > Feature Configuration > IPSecurity > IPSec > IPSec Proposal; CME
batch modification center: not supported) to add an IPsec proposal.
7. Run the NodeB MML command ADD IPSECPOLICY (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > IPSec > IPSec Policy; CME batch modification
center: not supported) to add an IPSec policy.
8. Run the NodeB MML command ADD IPSECBIND (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > IPSec > IPSec Policy Group Binding; CME batch
modification center: not supported) to bind an IPSec policy to a port.
Scenario 4: PSK-based Networking for a NodeB Using Separate Encryption
Figure 295-4 Example of PSK-based networking for a NodeB using separate encryption
The UMTS UMPT provides IPSec for signaling and service data streams on the NodeB,
not for O&M data streams on the NodeB.
1. Run the NodeB MML command SET IKECFG (CME single configuration: NodeB
Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > IKE > IKE Basic Configuration; CME batch
modification center: not supported) to set local IKE configurations.
2. Run the NodeB MML command ADD IKEPROPOSAL (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > IKE > IKE Proposal; CME batch modification
center: not supported) to add an IKE proposal.
3. Run the NodeB MML command ADD IKEPEER (CME single configuration: NodeB
Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > IKE > IKE Peer; CME batch modification center:
not supported) to add an IKE peer.
4. Run the NodeB MML command ADD ACL (CME single configuration: NodeB
Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > ACL > Access Control List; CME batch modification
center: not supported) to add an ACL.
5. Run the NodeB MML command ADD ACLRULE (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > Ipsecurity > ACL > Access Control List Rule; CME batch
modification center: not supported) to add a rule to the ACL.
6. Run the NodeB MML command ADD IPSECPROPOSAL (CME single
configuration: NodeB Configuration Express > IUB_NodeB > IP Transport
Layer > Feature Configuration > IPSecurity > IPSec > IPSec Proposal; CME
batch modification center: not supported) to add an IPsec proposal.
7. Run the NodeB MML command ADD IPSECPOLICY (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > IPSec > IPSec Policy; CME batch modification
center: not supported) to add an IPSec policy.
8. Run the NodeB MML command ADD IPSECBIND (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > IPSec > IPSec Policy Group Binding; CME batch
modification center: not supported) to bind an IPSec policy to a port.
l Verification Procedure
1. Run the NodeB MML command DSP IKESA. Check whether IKE SA data is
displayed in the returned result. If IKE SA data is displayed, go to step 2. If IKE SA
data is not displayed, IPSec fails to be activated.
2. Run the NodeB MML command DSP IPSECSA. Check whether IPSec SA data is
displayed in the returned result. If IPSec SA data is displayed, this feature has been
activated.
3. Run the NodeB MML command LST ACLRULE to check the ACL rules and
determine whether service data is protected by IPSec tunnels. Check whether the
protected services are running normally. For example, if voice services are protected
by IPSec tunnels, place a call to check whether voice services are still running
normally; if management plane packets are protected by IPSec tunnels, check whether
the corresponding NodeB is still online on the topology view of the M2000.
l Deactivation Procedure
1. Run the NodeB MML command RMV IPSECBIND (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > IPSec > IPSec Policy Group Binding; CME batch
modification center: not supported) to remove the binding between an IPSec policy
and a port.
2. Run the NodeB MML command RMV IPSECPOLICY (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > IPSec > IPSec Policy; CME batch modification
center: not supported) to remove an IPSec policy.
3. Run the NodeB MML command RMV IPSECPROPOSAL (CME single
configuration: NodeB Configuration Express > IUB_NodeB > IP Transport
Layer > Feature Configuration > IPSecurity > IPSec > IPSec Proposal; CME
batch modification center: not supported) to remove an IPSec proposal.
4. Run the NodeB MML command RMV ACLRULE (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > Ipsecurity > ACL > Access Control List Rule; CME batch
modification center: not supported) to remove a rule from an ACL.
5. Run the NodeB MML command RMV ACL (CME single configuration: NodeB
Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > ACL > Access Control List; CME batch modification
center: not supported) to remove the ACL.
6. Run the NodeB MML command RMV IKEPEER (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > IKE > IKE Peer; CME batch modification center:
not supported) to remove an IKE peer.
7. Run the NodeB MML command RMV IKEPROPOSAL (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > IKE > IKE Proposal; CME batch modification
center: not supported) to remove an IKE proposal.
----End
Example
//Activation procedure
//Scenario 1: PKI-based Networking for a NodeB Using Unified Encryption
//Adding an IKE proposal
ADD IKEPROPOSAL: PROPID=10, ENCALG=3DES, AUTHALG=MD5,
AUTHMETH=IKE_RSA_SIG, DHGRP=DH_GROUP14, DURATION=86400;
//Adding an IKE peer
ADD IKEPEER: PEERNAME="ike", PROPID=10, IKEVERSION=IKE_V1, EXCHMODE=MAIN,
IDTYPE=IP, REMOTEIP="90.90.90.90", REMOTENAME="secgw", DPD=PERIODIC,
DPDIDLETIME=20, DPDRETRI=4, DPDRETRN=6, LOCALIP="20.20.20.188";
//Adding an ACL
ADD ACL: ACLID=3000, ACLDESC="for IPsec";
//Adding a rule to the ACL
ADD ACLRULE: ACLID=3000, RULEID=1, PT=IP, SIP="32.32.32.1",
SWC="0.0.0.0", DIP="15.15.15.15", DWC="0.0.0.0", MDSCP=NO;
ADD ACLRULE: ACLID=3000, RULEID=2, PT=IP, SIP="30.30.30.1",
SWC="0.0.0.0", DIP="60.60.60.60", DWC="0.0.0.0", MDSCP=NO;
ADD ACLRULE: ACLID=3000, RULEID=3, PT=IP, SIP="30.30.30.1",
SWC="0.0.0.0", DIP="88.88.88.88", DWC="0.0.0.0", MDSCP=NO;
ADD ACLRULE: ACLID=3000, RULEID=4, PT=IP, SIP="30.30.30.1",
SWC="0.0.0.0", DIP="86.86.86.86", DWC="0.0.0.0", MDSCP=NO;
//Adding an IPSec proposal
REPLAYWND=WND_DISABLE;
//Adding the binding between an IPSec policy and a port
ADD IPSECBIND: CN=0, SRN=0, SN=7, SBT=BASE_BOARD, PT=ETH, PN=1,
SPGN="Policy0";
//Verification procedure
DSP IKESA:;
DSP IPSECSA: SN=7, SPGN="Policy0", SPSN=1;
LST ACLRULE:;
//Deactivation procedure
RMV IPSECBIND: SN=7, SBT=BASE_BOARD, PT=ETH, PN=1;
RMV IPSECPOLICY: SPGN="Policy0, SPSN=1;
RMV IPSECPROPOSAL: PROPNAME="prop0";
RMV ACLRULE: ACLID=3000, RULEID=1;
(Optional)RMV ACLRULE: ACLID=3000, RULEID=2;
(Optional)RMV ACLRULE: ACLID=3000, RULEID=3;
(Optional)RMV ACLRULE: ACLID=3000, RULEID=4;
RMV ACL: ACLID=3000;
RMV IKEPEER: PEERNAME="ike";
RMV IKEPROPOSAL: PROPID=10;
This section describes how to activate, verify, and deactivate the optional feature WRFD-140210
NodeB PKI Support. (This feature cannot be configured using the CME. )
Prerequisites
l Dependencies on Hardware
The 3900 series base stations must be configured with the UTRPc or UMPT board to
support this feature.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
On a live network, the operator's Certificate Authority (CA) that supports Certificate
Management Protocol version 2 (CMPv2) has been deployed.
An SeGW has been deployed to support IP Security (IPSec) on the RNC side.
The device certificate has been obtained.
Huawei device certificates have been configured for the NodeB.
Context
l Precautions
Public key infrastructure (PKI) is implemented on the M2000. Therefore, you must run
MML commands on the M2000 to activate PKI.
l Data Preparation
Prepare the data related to certificate deployment on the NodeB (the
CERTDEPLOY MO).
Cabinet No. CN -
Slot No. SN -
Signature SIGNALG -
Algorithm
Prepare the data related to the certificate request template (the CERTREQ MO).
Parameter Name Parameter ID Setting Source
Description
Country COUNTRY -
Organization ORG -
Organizational ORGUNIT -
Unit
Locality LOCALITY -
Prepare the data related to the device certificate (the CERTMK MO).
The active certificate is the device certificate that is currently used by a NodeB (the
APPCERT MO).
Parameter Name Parameter ID Setting Source
Description
Prepare the data related to the trust certificate (the TRUSTCERT MO).
Prepare the data related to the task of periodically checking certificate validity (the
CERTCHKTSK MO).
Parameter Name Parameter ID Setting Source
Description
(Optional) If the NodeB needs to obtain certificate revocation list (CRL) information
from the CA, prepare the data related to the CRL (the CRL MO).
Prepare the data related to the CRL application policy (the CRLPOLICY MO).
Parameter Name Parameter ID Setting Source
Description
Prepare the data related to the task of periodically downloading the CRL (the
CRLTSK MO).
Parameter Name Parameter ID Setting Source
Description
Password PWD -
Task ID TSKID -
Procedure
l Activation Procedure
1. Run the NodeB MML command SET CERTDEPLOY to set the board where a
certificate is to be deployed on the NodeB.
2. Run the NodeB MML command ADD CA to add the operator's CA server.
3. Run the NodeB MML command DLD CERTFILE to download an operator's trust
root certificate.
4. Run the NodeB MML command ADD TRUSTCERT to add an operator's trust
certificate.
5. Run the NodeB MML command MOD CERTREQ to modify configurations of a
certificate request template.
6. Run the NodeB MML command REQ DEVCERT to apply for a device certificate
through a CMP session.
7. Run the NodeB MML command MOD APPCERT to modify configurations of an
active certificate. In this step, set Application Type to IKE(IKE).
8. Run the NodeB MML command SET CERTCHKTSK to set a task of periodically
checking certificate validity.
9. Optional: Run the NodeB MML command DLD CERTFILE to download the CRL
file.
10. Optional: Run the NodeB MML command ADD CRL to add a CRL.
11. Optional: Run the NodeB MML command ADD CRLTSK to add a task of
periodically downloading the CRL.
l Verification Procedure
1. Run the NodeB MML command DSP APPCERT. Check the value of Status in the
returned result. If NORMALLY is displayed, the device certificate has been loaded
to the NodeB.
2. Run the NodeB MML command DSP TRUSTCERT. Check the value of Status in
the returned result. If NORMALLY is displayed, the trust certificate has been loaded
to the NodeB.
3. Optional: Run the NodeB MML commandDSP CRL. Check the value of Status in
the returned result. If NORMALLY is displayed, the CRL has been loaded to the
NodeB.
4. After IPSec policies authenticated by the digital certificate take effect, Run the NodeB
MML commandDSP IKESA. Check the value of SA Flag in the returned result. If
READY is displayed, an IKE SA has been established.
l Deactivation Procedure
1. Run the NodeB MML command SET CERTDEPLOY. In this step, set Certification
Deploy Position Type to NULL(NULL).
----End
Example
//Activation procedure
//(Optional)Adding a CRL
ADD CRL: CERTNAME="NodeB.crl";
//Verification procedure
DSP APPCERT: APPTYPE=IKE;
DSP TRUSTCERT: CERTNAME="OperationCA.cer";
DSP CRL: CERTNAME="NodeB.crl";
DSP IKESA: CN=0, SRN=0, SN=4, IKEVSN=IKE_V1;
//Deactivation procedure
SET CERTDEPLOY: DEPLOYTYPE=null;
This section describes how to activate, verify, and deactivate the optional feature WRFD-140220
Intelligent Battery Management. (This feature cannot be configured using the CME. )
Prerequisites
l Dependencies on Hardware
The APM30H (Ver. C), BTS3900AL, TP48600A, and batteries must be configured.
l Dependencies on Other Features
This feature does not depend on other features.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Others
In a base station newly updated to RAN14.0 or later, update the PMU software version
to version corresponding to R14.0 or later and then activate the PMU software. In
addition, ensure that the PMU software version can work with the software version of
the base station.
In a new base station, activating the PMU software is not required because the PMU
software version delivered with the software version of the base station has been up to
date.
Context
The intelligent power management feature has the following functions: automatic switch
between the charge and discharge modes, self-protection under high temperature, and battery
runtime display. This feature enables the base station to prolong the battery lifespan by battery
self-protection, and therefore increase profits of operators by reducing operating expenses.
l Precautions
Check the local grip type. If the grid type is 1 or 2, it is recommended that the function
of automatic switch between the charge and discharge modes be enabled.
Check the ambient temperature of the base stations and determine the policies and
parameters for battery self-protection under high temperature.
l Data Preparation
Paramet Parame Description Data Source
er Name ter ID
Procedure
l Activation Procedure
1. (Optional) Activate the PMU software: Run the NodeB MML command ACT
SOFTWARE to activate the PMU software. Run the NodeB MML command DSP
BRDVER to query the PMU software version and ensure the version has been
upgraded to version corresponding to R14.0 or later.
2. Run the NodeB MML command SET EQUIPMENT. In this step, set Battery
Intelligent Management Swtich to ON.
3. Run the NodeB MML command ADD BATTERY or MOD BATTERY. In this step,
set High Temperature Shutdown Flag to ENABLE, Shutdown Temperature to
53, and Temperature Alarm Upper Threshold to 50.
l Verification Procedure
1. Intelligent Battery Management: Run the NodeB MML command DSP PMU to check
the values of Battery Intelligent Management Capability and Battery Intelligent
Management Mode.
Expected result: The value of Battery Intelligent Management Capability is
Support, and the value of Battery Intelligent Management Mode is ENABLE.
2. Self-Protection Under High Temperature: Run the NodeB MML command LST
BATTERY to check the values High Temperature Shutdown Flag, Shutdown
Temperature, and Temperature Alarm Upper Threshold.
Expected result: The value of High Temperature Shutdown Flag is ENABLE. The
value of Shutdown Temperature is 53. The value of Temperature Alarm Upper
Threshold is 50.
3. Battery Runtime Display: Run the NodeB MML command DSP BATTERY to check
the value of Remaining Time to get the battery leftover capacity.
l Deactivation Procedure
1. Run the NodeB MML command SET EQUIPMENT. In this step, set Battery
Intelligent Management Swtich to OFF.
----End
Example
/*Activation procedure*/
//Activating BIMS
SET EQUIPMENT: BATIMS=ON;
//Setting HTSDF, SDT, and TUTHD
ADD BATTERY: HTSDF=ENABLE, SDT=53, TUTHD=50;
/*Deactivation procedure*/
//Deactivating BATIMS
SET EQUIPMENT: BATIMS=OFF;
This section describes how to activate, verify, and deactivate the optional feature MRFD-221801
Multi-mode Dynamic Power Sharing (UMTS).
Prerequisites
l Dependencies on Hardware
Only the MRFU and the MRRU supports GSM and UMTS Dynamic Power Sharing at
present.
l Dependencies on Other Features
This feature can't be activated with WRFD-010684 22 MIMO or WRFD-010693 DL
64QAM+MIMO simultaneously.
This feature has to be activated with MRFD-211801 Multi-mode Dynamic Power
Sharing (GSM) simultaneously.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
The UMTS cell must exist HSDPA Carry.
Context
In the case of a 3900 series multi-mode base station, the GSM and UMTS TRXs can share one
power amplifier. When there is unbalanced traffic in the GSM and the UMTS, the power can be
used more efficiently in an effective way, namely, sharing the power amplifier. The overall
network quality of the GSM and the UMTS is therefore improved.
NOTE
l The feature may fail to recall the shared power in one second when the GSM services increase suddenly.
As a result, internal GSM peak clipping occurs, which affects service quality.
l Enabling the feature may cause the UMTS coverage to shrink and therefore increase the drop rate. The
problem can be addressed by handing over services in marginal coverage to a GSM/UMTS cell under
the same coverage as the original UMTS.
l The switch and other parameter configurations are performed only on the GSM side. The UMTS side
requires no configuration.
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET BTSGUPWRSHRFP (CME single
configuration: BTS Configuration Express > BTS Power > BTS GU Dynamic
Power Sharing Parameters; CME batch modification center: not supported). In this
step, set Board Parameter Configuration Enabled to YES(YES) and set the period
for enabling GU power sharing.
2. Run the BSC6900 MML command SET BTSRXUBP (CME single configuration:
BTS Device Panel > RXU Topology > Right click RXU Board > RXU Board
Porperties > RUX board Parameters; CME batch modification center: not
supported). In this step, setRXU Board Type to MRRU(MRRU) or MRFU
(MRFU), set GU Dynamic Power Sharing Switchto YES(YES), and set parameters
Minimum Number of Non-BCCH TRXs in GSM for GU Power Sharing, GSM
Power Load Threshold for GU Power Sharing, Number of Checked Timeslots
for Retrieving Shared Power, Num of Timeslots Meet Requirements for
Retrieving Shared Pwr, GSM Power Reserve Coefficient for Retrieving Shared
Power, GSM Idle Channel Threshold for GU Power Sharing, GSM Idle Channel
Hysteresis for GU Power Sharing, GSM Power Reserve in Low Load for GU
Power Sharing, GSM Power Reserve in High Load for GU Power Sharing,
Maximum Accumulated Shared Power That UMTS Can Accept, Maximum
Shared Power That UMTS Can Accept In Each Period to actual conditions.
3. Run the NodeB MML command MOD LOCELL (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Radio Layer > xx Sector > Locell; CME
batch modification center: 3.17 Modifying Physical NodeB Parameters in
Batches), set GU Power Share Flag to TRUE(TRUE).
l Verification Procedure
1. Run the BSC6900 MML command LST BTSGUPWRSHRFP and LST
BTSRXUBP and check the returned message.
Exception result: Board Parameter Configuration Enabled and GU Dynamic
Power Sharing Switch are YES.
2. Run the NodeB MML command LST LOCELL, and check the returned message.
Exception result: GU Power Share Flag is YES.
l Deactivation Procedure
1. Run the NodeB MML command MOD LOCELL (CME single configuration: NodeB
Configuration Express > IUB_NodeB > Radio Layer > xx Sector > Locell; CME
batch modification center: 3.17 Modifying Physical NodeB Parameters in
Batches), set GU Power Share Flag to FALSE(FALSE).
2. Run the BSC6900 MML command SET BTSGUPWRSHRFP (CME single
configuration: BTS Configuration Express > BTS Power > BTS GU Dynamic
Power Sharing Parameters; CME batch modification center: not supported). In this
step, set Board Parameter Configuration Enabled to NO(NO).
3. Run the BSC6900 MML command SET BTSRXUBP (CME single configuration:
BTS Device Panel > RXU Topology > Right click RXU Board > RXU Board
Porperties > RUX board Parameters; CME batch modification center: not
supported). In this step, set GU Dynamic Power Sharing Switch to NO(NO).
NOTE
GSM and UMTS Dynamic Power Sharing can be deactivated by performing either of the two
steps discussed above.
----End
Example
//Activation procedure
SET BTSGUPWRSHRFP: IDTYPE=BYID, BTSID=1, CFGFLAG=YES,
GUPWRSHARESTM1=07&00, GUPWRSHAREETM1=09&00, GUPWRSHARESTM2=10&00,
GUPWRSHAREETM2=12&00, GUPWRSHARESTM3=14&00, GUPWRSHAREETM3=16&00,
GUPWRSHARESTM4=20&00, GUPWRSHAREETM4=22&00;
SET BTSRXUBP: IDTYPE=BYID, BTSID=1, RXUIDTYPE=SRNSN, CN=0, SRN=4, SN=0,
RXUTYPE=MRFU, GUPWRSHARESWITCH=YES,
GUPWRSHARETRXNUM=1, GUPWRSHAREPWRLOAD=80, GUPWRSHAREN=8, GUPWRSHAREP=6,
GUPWRSHARERSVFACTOR=50, GUPWRSHAREGSMIDLETH=12,
GUPWRSHAREGSMIDLEHS=2, GUPWRSHAREGSMIDLERSVPWR=5,
GUPWRSHAREGSMBUSYRSVPWR=10, GUPWRSHAREURCVPWR=15, GUPWRSHAREURCVPWRPD=5;
MOD LOCELL: LOCELL=0, SECT=LOCAL_SECTOR, GUPOWERSHARE=TRUE;
//Verification procedure
LST BTSGUPWRSHRFP: IDTYPE=BYID, BTSID=1, LSTFORMAT=VERTICAL;
LST BTSRXUBP: IDTYPE=BYID, BTSID=1, RXUIDTYPE=SRNSN, CN=0, SRN=4, SN=0,
LSTFORMAT=VERTICAL;
LST LOCELL: MODE=LOCALCELL, LOCELL=0;
//Deactivation procedure
SET BTSGUPWRSHRFP: IDTYPE=BYID, BTSID=1, CFGFLAG=NO;
SET BTSRXUBP: IDTYPE=BYID, BTSID=1, RXUIDTYPE=SRNSN, CN=0, SRN=4, SN=0,
RXUTYPE=MRFU, GUPWRSHARESWITCH=NO;
MOD LOCELL: LOCELL=0, SECT=LOCAL_SECTOR, GUPOWERSHARE=FALSE;
This section describes how to activate, verify, and deactivate the optional feature MRFD-221802
GSM and UMTS Dynamic Spectrum Sharing (UMTS). This feature enables the spectrum
resources to be dynamically shared between the GSM and UMTS networks based on their traffic
load, improving frequency utilization.
Prerequisites
l Dependencies on Hardware
The 900 MHz MRFU and MRRU must support this feature.
GSM and UMTS sharing the same MRFU/MRRU.
l Dependencies on Other Features
On the dynamic spectrum shared carrier, this feature can not be activated with
MRFD-211703 2.0MHz Central Frequency point separation between GSM and UMTS
mode(GSM), MRFD-221703 2.0MHz Central Frequency point separation between
GSM and UMTS mode(UMTS) simultaneously
This feature can not be activated with GBFD-117001 Flex MAIO simultaneously.
This feature has to be activated with MRFD-211802 GSM and UMTS Dynamic
Spectrum Sharing (GSM) simultaneously.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Start Dynamic Spectrum Sharing on the M2000 by referring to the M2000 Online Help.
l Other Prerequisites
A specific M2000 V200R011 version that matches SRAN6.0 is required to support this
feature.
GSM and UMTS sharing the same MRFU/MRRU.
Context
The dynamic spectrum sharing (DSS) between GSM and UMTS increases network throughput
and reduces the total cost of data services because UMTS has higher spectral efficiency than
GSM. In theory, the maximum throughput gain is about 50%. After this feature is used, the total
cost of ownership (TCO) of mobile broadband (MBB) can be reduced, and dynamic GSM/
UMTS refarming can be implemented. Thus, the maintenance cost of manual refarming is
reduced.
Procedure
l Activation Procedure
1. Configuration on the RNC side
a. Run the BSC6900 MML command MOD UNODEB (CME single
configuration: NodeB Configuration Express > IUB_RNC > NodeB Basic
Information > NodeB; CME batch modification center: not supported) with
DSS NodeB Flag set to TRUE.
b. Run the BSC6900 MML command ADD UCELLQUICKSETUP (CME single
configuration: Main View > Right click NodeB > Add UMTS Cell; CME batch
modification center: not supported) to set up a DSS cell, set DSS Cell Flag to
TRUE, and set Maximum TX Power in Small DSS Coverage and PCPICH
TX Power in Small DSS Coverage based on network conditions.
c. Run the BSC6900 MML command MOD UCELLACCESSSTRICT (CME
single configuration: UMTS Cell Configuration Express > Cell Parameters
> Cell Access Restriction Information; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches) with both Cell barred
indicator for SIB3 and Cell barred indicator for SIB4 of DSS cells set to
BARRED.
d. Run the BSC6900 MML command ADD UINTERFREQNCELL (CME single
configuration: UMTS Cell Configuration Express > Neighboring Cell >
Inter-frequency Neighboring Cell; CME batch modification center: not
supported) to add the neighbor 3G cells of DSS cells as inter-frequency
neighboring cells, and set Blind Handover Flag to TRUE and
DrdOrLdrFlag to TRUE.
e. Run the BSC6900 MML command ADD U2GNCELL (CME single
configuration: UMTS Cell Configuration Express > Neighboring Cell > GSM
Neighboring Cell; CME batch modification center: not supported) to add the
neighboring GSM cells for DSS cells, and set Blind Handover Flag to TRUE.
f. Run the BSC6900 MML command ADD U2GNCELL (CME single
configuration: UMTS Cell Configuration Express > Neighboring Cell > GSM
Neighboring Cell; CME batch modification center: not supported) to add the
neighboring DSS cells as intra-frequency neighboring cells.
g. Run the BSC6900 MML command SET UCORRMALGOSWITCH (CME
single configuration: UMTS Radio Global Configuration Express >
Connection_Oriented RRM Switch Configuration > Connection Oriented
Algorithm Switches; CME batch modification center: 3.15 Modifying RNC
Parameters in Batches) with both DRD switch for single RAB and
HO_INTER_FREQ_HARD_HO_SWITCH set to ON.
h. Run the BSC6900 MML command SET UDRD (CME single configuration:
UMTS Radio Global Configuration Express > Directed Retry Parameter
Configuration > RNC-Oriented DRD Algorithm Parameters; CME batch
modification center: 3.15 Modifying RNC Parameters in Batches) with Load
balance DRD switch for HSDPA set to ON and Load Balancing DRD
Choice set to UserNumber.
CAUTION
The parameter Spectrum Sharing Shutdown Allowed for all TRXs to be shared
under a base station should be set to YES(Yes) except for the BCCH TRX.
l Verification Procedure
1. Start spectrum sharing on the M2000 manually.
2. Run the BSC6900 MML command DSP UNODEB to query the DSS status of a
NodeB.
Expected result: The value of NodeB DSS state is Actived in Normal DSS
coverage.
3. Run the BSC6900 MML command DSP UCELL to query the DSS status of a cell.
Expected result: The value of DSS state is Actived in Normal DSS coverage.
4. Run the NodeB MML command LST LOCELL to check the value of GU Power
Share Flag.
Expected result: The value of GU Power Share Flag is TRUE.
5. Run the BSC6900 MML command DSP BTSSTAT to query the value of Dynamic
Spectrum Sharing. Expected result: The value of Dynamic Spectrum Sharing is
Yes.
l Deactivation Procedure
1. Stop Dynamic Spectrum Sharing on the M2000 by referring to the M2000 Online
Help.
2. Run the BSC6900 MML command MOD UNODEB (CME single configuration:
NodeB Configuration Express > IUB_RNC > NodeB Basic Information >
NodeB; CME batch modification center: not supported) with DSS NodeB Flag set to
FALSE.
3. Run the BSC6900 MML command SET GDSSPARA (CME single configuration:
BTS Configuration Express > BTS Basic Attributes > BTS Spectrum Sharing
Parameters; CME batch modification center: not supported) with Spectrum Sharing
Allowed set to NO(No).
4. Run the BSC6900 MML command SET GTRXDEV (CME single configuration:
TRX Configuration Express > Site TRX Dev Property > Site TRX Dev
Property; CME batch modification center: Modifying GSM TRX Parameters in
Batches) with Spectrum Sharing Shutdown Allowed set to NO(No).
5. Remove the neighboring cell by referring to Reconfiguration Guide.
6. Run the BSC6900 MML command DEA UCELL (CME single configuration: UMTS
Cell Configuration Express > Cell Basic Information > Cell Basic Information.
Set Validation indication to Deactivated; CME batch modification center: 3.18
Modifying UMTS Cell Parameters in Batches) to deactivate a cell.
----End
Example
//Activation procedure
MOD UNODEB: NodeBId=1, DSSFlag=TRUE;
ADD UCELLQUICKSETUP: CellId=102, CellName="dss102", PeerIsValid=INVALID,
CnOpGrpIndex=0, BandInd=Band2, UARFCNDownlink=412, PScrambCode=0,
TCell=CHIP256, LAC=1, SAC=0, CfgRacInd=NOT_REQUIRE, SpgId=1, URANUM=D1,
URA1=0, NodeBName="102", LoCell=102, SupBmc=FALSE, DSSFlag=TRUE,
DSSSmallCovMaxTxPower=431, DSSSmallCovPCPICHPower=331;
MOD UCELLACCESSSTRICT: CellId=102, IdleCellBarred=BARRED,
IdleIntraFreqReselection=ALLOWED, IdleTbarred=D320,
ConnCellBarred=BARRED, ConnIntraFreqReselection=ALLOWED,
ConnTbarred=D320;
ADD UINTERFREQNCELL: RNCId=0, CellId=102, NCellRncId=1, NCellId=105,
SIB11Ind=TRUE, SIB12Ind=FALSE, TpenaltyHcsReselect=D0, BlindHoFlag=TRUE,
NPrioFlag=FALSE, DrdOrLdrFlag=TRUE, InterNCellQualReqFlag=FALSE;
ADD U2GNCELL: RNCId=2, CellId=102, GSMCellIndex=120, BlindHoFlag=TRUE,
NPrioFlag=FALSE;
ADD UINTRAFREQNCELL: RNCId=0, CellId=102, NCellRncId=3, NCellId=121,
SIB11Ind=TRUE, SIB12Ind=FALSE, TpenaltyHcsReselect=D0, NPrioFlag=FALSE;
SET UCORRMALGOSWITCH: DrSwitch=DR_RAB_SING_DRD_SWITCH-1,
HoSwitch=HO_INTER_FREQ_HARD_HO_SWITCH-1;
This section describes how to activate, verify, and deactivate the optional feature MRFD-221501
IP-Based Multi-Mode Co-Transmission on Base Station Side. For details about data
configurations, see section Configuration Reference > MBTS Configuration Reference
(V100R007C00) > Common Transmission in the 3900 Series Base Station Initial
Configuration Guide, or see section Common Transmission in the WCDMA RAN Feature
Documentation. The latest 3900 Series Base Station Initial Configuration Guide can be obtained
from the following path: HUAWEI Technical Support (support.huawei.com), Support >
Documentation > SingleRAN > MBTS > SingleRAN7.0.
This section describes how to activate, verify, and deactivate the optional feature MRFD-221504
TDM-Based Multi-mode Co-Transmission via Backplane on BS side (NodeB). (This feature
cannot be configured using the CME. )
Prerequisites
l Dependencies on Hardware
A GSM and UMTS dual-mode base station supports this feature.
When the TDM timeslot cross connection co-transmission feature is supported by a
GSM and UMTS dual-mode base station, a UTRP should be configured for the BTS.
The UTRP type must be UTRP3, UTRP4, or UTRPb4.
l Dependencies on Other Features
WRFD-050302 Fractional ATM Function on Iub Interface
WRFD-050411 Fractional IP Function on Iub Interface
l License
This feature is not under license control.
Context
This feature enables the BTS and NodeB to share E1/T1 transmission resources through a
backplane clock channel with the effective TDM timeslot cross connection function.
l The number of E1/T1 on the BTS backplane is within the range of 16 through 19. E1/T1 numbers 16 through
19 on the BTS backplane correspond to E1/T1 numbers 0 through 3 on the NodeB backplane. Cross
connection is not supported. For example, E1/T1 No. 16 on the BTS backplane only corresponds to E1/T1
No. 0 on the NodeB backplane.
l E1 timeslot numbers configured on the BTS side must be consistent with those configured on the NodeB
side.
Procedure
l Activating the BTS data (GTMU-based)
1. Run the BSC6900 MML command ADD BTSCONNECT to add a connection
between a GTMU port and the NodeB. Set Dest Node Type (select Connect to
BSC on the CME) to OTHER.
2. Run the BSC6900 MML command ADD BTSTOPCONFIG to configure the TOP
switching parameters.
Set Port Subrack No. and Port Slot No. to numbers of the subrack and slot where
the BTS port connected to the NodeB interface board is located. Set TOP Board
Subrack No. and TOP Board Slot No. to numbers of the subrack and slot where
the NodeB interface board is located.
Set Port Type to TOPEXTOUTPORT.
Set TS Mask to the timeslot of the NodeB backplane.
NOTE
When E1 transmission resources on the BTS side are shared by the NodeB, set Port Type to
TOPEXTOUTPORT.
l Activating the NodeB data (GTMU-based)
1. Run the NodeB MML command ADD BACKE1T1 to add a backplane E1/T1 link.
Set Subrack No. and Slot No. to numbers of the subrack and slot that house the
Iub interface board.
Set Subboard Type to BACK_BOARD.
Set Destination Slot No. to the number of the slot that houses the GTMU.
NOTE
Similar to a common E1, the backplane E1 can be configured with the upper-layer bearer. It,
however, does not support the configuration of the operating work mode and loopback mode, and
online and offline tests. The upper-layer link bearer of the backplane E1 can be UNILNK/IMALNK/
FRAATMLNK/PPLNK/MPLNK. You need to configure the link bearer according to actual
networking mode.
2. Run the NodeB MML command ADD IMAGRP to add an IMA group. In this step,
set Subboard Type to BASE_BOARD.
3. Run the NodeB MML command ADD IMALNK to add an IMA link and then add it
to the MP group. In this step, set Subboard Type to BACK_BOARD or
BASE_BOARD.
4. Run the NodeB MML command ADD SAALLNK to add an SAAL link.
Set Subboard Type to BASE_BOARD.
Set Rate Unit to KBPS or CELL/S. Only one rate unit can be used. Therefore,
rate units in other configuration must be consistent.
5. Run the NodeB MML command ADD AAL2NODE to add an AAL2 node.
Set Node Type to LOCAL(LOCAL).
Set ATM Address to a valid ATM address. The recommended value is
H'3900000000000000000000000000000000000000.
6. Run the NodeB MML command ADD AAL2PATH to add an AAL2 path.
Set Node Type to LOCAL(End Node).
Set Subboard Type to BASE_BOARD.
Set Rate Unit to KBPS or CELL/S. Only one rate unit can be used. Therefore,
rate units in other configuration must be consistent.
7. Run the NodeB MML command ADD IUBCP to add an NCP link. In this step, set
NCP/CCP Port Type to NCP(NCP Port).
8. Run the NodeB MML command ADD IUBCP to add a CCP link. In this step, set
NCP/CCP Port Type to CCP(CCP Port).
NOTE
Before a CCP link is added, the number of the CCP port must be the same as that of the CCP port
on the BSC6900 side. To query information about the CCP link on the BSC6900 side, run the
BSC6900 MML command LST UIUBCP.
l Activating the BTS data (GSM-UTRP-based)
1. Run the BSC6900 MML command ADD BTSCONNECT to add a connection
between a UTRP port and the NodeB. Set Dest Node Type (select Connect to BSC
on the CME) to OTHER.
2. Run the BSC6900 MML command ADD BTSTOPCONFIG to configure the TOP
switching parameters.
Set Port Type to TOPEXTOUTPORT.
Set TS Mask to the timeslot of the NodeB backplane.
NOTE
When E1 transmission resources on the BTS side are shared by the NodeB, set Port Type to
TOPEXTOUTPORT.
l Activating the NodeB data (GSM-UTRP-based)
1. Run the NodeB MML command ADD BACKE1T1 to add a backplane E1/T1 link.
Set Cabinet No., Subrack No., and Slot No. to the numbers of the cabinet,
subrack, and slot that house the Iub interface board.
Set Subboard Type to BACK_BOARD.
Set Destination Slot No. to the number of the slot that houses the UTRP.
NOTE
Similar to a common E1, the backplane E1 can be configured with the upper-layer bearer. It,
however, does not support the configuration of the operating work mode and loopback mode, and
online and offline tests. The upper-layer link bearer of the backplane E1 can be UNILNK/IMALNK/
FRAATMLNK/PPLNK/MPLNK. You need to configure the link bearer according to actual
networking mode.
2. Run the NodeB MML command ADD IMAGRP to add an IMA group. In this step,
set Subboard Type to BASE_BOARD.
3. Run the NodeB MML command ADD IMALNK to add an IMA link and then add it
to the MP group. In this step, set Subboard Type to BACK_BOARD or
BASE_BOARD.
4. Run the NodeB MML command ADD SAALLNK to add an SAAL link.
Set Subboard Type to BASE_BOARD.
Set Rate Unit to KBPS or CELL/S. Only one rate unit can be used. Therefore,
rate units in other configuration must be consistent.
5. Run the NodeB MML command ADD AAL2NODE to add an AAL2 node.
Set Node Type to LOCAL(LOCAL).
Set ATM Address to a valid ATM address. The recommended value is
H'3900000000000000000000000000000000000000.
6. Run the NodeB MML command ADD AAL2PATH to add an AAL2 path.
Set Node Type to LOCAL(End Node).
Set Subboard Type to BASE_BOARD.
Set Rate Unit to KBPS or CELL/S. Only one rate unit can be used. Therefore,
rate units in other configuration must be consistent.
7. Run the NodeB MML command ADD IUBCP to add an NCP link. In this step, set
NCP/CCP Port Type to NCP.
8. Run the NodeB MML command ADD IUBCP to add a CCP link. In this step, set
NCP/CCP Port Type to CCP.
NOTE
Before a CCP link is added, the number of the CCP port must be the same as that of the CCP port
on the BSC6900 side. To query information about the CCP link on the BSC6900 side, run the
BSC6900 MML command LST UIUBCP.
----End
Example
//Activating the BTS data (GTMU-based)
//Configuring a connection between a GTMU port and the NodeB
ADD BTSCONNECT: IDTYPE=BYID, BTSID=255, INPN=1, INCN=0, INSRN=0, INSN=6,
DESTNODE=OTHER;
//Configuring the TOP switching relation between the GTMU and the WMPT:
E1 port 16 on the backplane corresponds to port 0 on the WMPT, the GTMU
provides the WMPT with a transmission path, the port type is TOPEXTINPO,
and the output port is E1 port 1 on the GTMU
ADD BTSTOPCONFIG: IDTYPE=BYID, BTSID=255, CN=0, SRN=0, SN=6,
E1T1PORTNO=16, TOPBOARDCN=0, TOPBOARDSRN=0, TOPBOARDSLOTNO=7,
PORTTYPE=TOPEXTOUTPORT, ORIPORT=1,
TSMASK=TS1-1&TS2-1&TS3-1&TS4-1&TS5-1&TS6-1&TS7-1&TS8-1&TS9-1&TS10-1&TS11-
1&TS12-1&TS13-1&TS14-1&TS15-1&TS16-1&TS17-1&TS18-1&TS19-1&TS20-1&TS21-1&T
S22-1&TS23-1&TS24-1&TS25-1&TS26-1&TS27-1&TS28-1&TS29-1&TS30-1&TS31-1;
This section describes how to activate, verify, and deactivate the optional feature MRFD-221601
Multi-Mode BS Common Reference Clock (NodeB). For details about data configurations, see
section Configuration Reference > MBTS Configuration Reference (V100R007C00) >
Common Clock in the 3900 Series Base Station Initial Configuration Guide, or see section
Common Clock in the WCDMA RAN Feature Documentation. The latest 3900 Series Base
Station Initial Configuration Guide can be obtained from the following path: HUAWEI
Technical Support (support.huawei.com), Support > Documentation > SingleRAN > MBTS
> SingleRAN7.0.
This section describes how to activate, verify, and deactivate the multi-mode feature
MRFD-221602 Multi-mode BS Common IPSec(UMTS).
Prerequisites
l Dependencies on Other Features
UMPT or UTRPc
l Dependencies on other features
MRFD-221501 IP-Based Multi-mode Co-Transmission on BS side (NodeB).
One mode of multi-mode shall support IPSec feature (GBFD-113524 BTS Integrated
IPsec, WRFD-140209 NodeB Integrated IPSec, LOFD-003009 IPsec).
This feature must be used together with one of features MRFD-211602 Multi-mode BS
Common IPSec (GSM) and MRFD-231602 Multi-mode BS Common IPSec (LTE), or
both.
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
IPSec Networking of an MBTS
l IPSec networking for a GU, GL, and UL dual-mode base station: IPSec-related data on the
UTRPc board is configured by the mode with the highest priority. During secure base
station deployment, all security-related configuration data is configured by the mode with
a higher priority. The mode with a lower priority does not participate in secure base station
deployment.
l IPSec networking for a GUL triple-mode base station:
GU+L (BBU interconnection): IPSec is implemented on the LMPT board, and the
UTRPc board forwards the LTE service data and processes UMTS and GSM IPSec
data. IPSec-related data on the UTRPc board is configured by the mode with a higher
priority. If digital certificates are used for identity authentication, the LMPT and UTRPc
boards use their respective digital certificates to authenticate with the SeGW.
GU+L (BBU interconnection): IPSec is implemented on the UMPT board, and the
UTRPc board forwards the UMTS service data and processes LTE and GSM IPSec
data. IPSec-related data on the UTRPc board is configured by the mode with a higher
priority. If digital certificates are used for identity authentication, the UMPT and UTRPc
boards use their respective digital certificates to authenticate with the SeGW.
In other BBU interconnection scenarios: The UTRPc board performs IPSec-related
processing. IPSec-related data on the UTRPc board is configured by the mode with a
higher priority. If digital certificates are used for identity authentication, the UTRPc
board uses its digital certificate to authenticate with SeGW, and the three mode of the
base station share the same IPSec tunnels and digital certificate.
l Data Preparation
Prepare the data required for the IKE proposal (the IKEPROPOSAL MO).
Parameter Name Parameter ID Setting Source
Description
Prepare the data required for the IKE peer (the IKEPEER MO).
Prepare the data required for the ACL rule (the ACL MO).
One or multiple ACLs need to be configured based on the planned IPSec tunnels. In the
IPSECPOLICY MO, an IPSec policy is bound to an ACL based on the ACLID setting.
Only data streams that comply with ACL rules are processed according to the operations
defined in the IPSec policy.
Parameter Name Parameter ID Setting Source
Description
Prepare the data required for the ACL rule (the ACLRULE MO).
Depending on the network plan, an IPSec tunnel may require multiple ACL rules to
protect different types of data streams.
Parameter Name Parameter ID Setting Source
Description
Protocol Type PT -
Destination DWC -
Wildcard
DSCP DSCP -
Prepare the data required for the IPSec proposal (the IPSECPROPOSAL MO).
Prepare the data required for the IPSec policy (the IPSECPOLICY MO).
Parameter Name Parameter ID Setting Source
Description
Prepare the data required for binding an IPSec policy group to a port (the
IPSECBIND MO).
Parameter Name Parameter ID Setting Source
Description
Slot No. SN -
If a PSK is used for authentication, prepare the IKE configuration data (the IKECFG
MO).
Parameter Name Parameter ID Setting Source
Description
Procedure
l Activation Procedure
Scenario 1: PKI-based Networking for a NodeB Using Unified Encryption
Figure 303-1 Example of PKI-based networking for a NodeB using unified encryption
1. Run the NodeB MML command ADD IKEPROPOSAL (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > IKE > IKE Proposal; CME batch modification
center: not supported) to add an IKE proposal.
2. Run the NodeB MML command ADD IKEPEER (CME single configuration: NodeB
Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > IKE > IKE Peer; CME batch modification center:
not supported) to add an IKE peer.
3. Run the NodeB MML command ADD ACL (CME single configuration: NodeB
Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > ACL > Access Control List; CME batch modification
center: not supported) to add an ACL.
4. Run the NodeB MML command ADD ACLRULE (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > Ipsecurity > ACL > Access Control List Rule; CME batch
modification center: not supported) to add a rule to the ACL.
5. Run the NodeB MML command ADD IPSECPROPOSAL (CME single
configuration: NodeB Configuration Express > IUB_NodeB > IP Transport
Layer > Feature Configuration > IPSecurity > IPSec > IPSec Proposal; CME
batch modification center: not supported) to add an IPsec proposal.
6. Run the NodeB MML command ADD IPSECPOLICY (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > IPSec > IPSec Policy; CME batch modification
center: not supported) to add an IPSec policy.
7. Run the NodeB MML command ADD IPSECBIND (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > IPSec > IPSec Policy Group Binding; CME batch
modification center: not supported) to bind an IPSec policy to a port.
Scenario 2: PKI-based Networking for a NodeB Using Separate Encryption
Figure 303-2 Example of PKI-based networking for a NodeB using separate encryption
Configuration > IPSecurity > IKE > IKE Proposal; CME batch modification
center: not supported) to add an IKE proposal.
2. Run the NodeB MML command ADD IKEPEER (CME single configuration: NodeB
Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > IKE > IKE Peer; CME batch modification center:
not supported) to add an IKE peer.
3. Run the NodeB MML command ADD ACL (CME single configuration: NodeB
Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > ACL > Access Control List; CME batch modification
center: not supported) to add an ACL.
4. Run the NodeB MML command ADD ACLRULE (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > Ipsecurity > ACL > Access Control List Rule; CME batch
modification center: not supported) to add a rule to the ACL.
5. Run the NodeB MML command ADD IPSECPROPOSAL (CME single
configuration: NodeB Configuration Express > IUB_NodeB > IP Transport
Layer > Feature Configuration > IPSecurity > IPSec > IPSec Proposal; CME
batch modification center: not supported) to add an IPsec proposal.
6. Run the NodeB MML command ADD IPSECPOLICY (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > IPSec > IPSec Policy; CME batch modification
center: not supported) to add an IPSec policy.
7. Run the NodeB MML command ADD IPSECBIND (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > IPSec > IPSec Policy Group Binding; CME batch
modification center: not supported) to bind an IPSec policy to a port.
Scenario 3: PSK-based Networking for a NodeB Using Unified Encryption
Figure 303-3 Example of PSK-based networking for a NodeB using unified encryption
1. Run the NodeB MML command SET IKECFG (CME single configuration: NodeB
Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > IKE > IKE Basic Configuration; CME batch
modification center: not supported) to set local IKE configurations.
2. Run the NodeB MML command ADD IKEPROPOSAL (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > IKE > IKE Proposal; CME batch modification
center: not supported) to add an IKE proposal.
3. Run the NodeB MML command ADD IKEPEER (CME single configuration: NodeB
Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > IKE > IKE Peer; CME batch modification center:
not supported) to add an IKE peer.
4. Run the NodeB MML command ADD ACL (CME single configuration: NodeB
Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > ACL > Access Control List; CME batch modification
center: not supported) to add an ACL.
5. Run the NodeB MML command ADD ACLRULE (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > Ipsecurity > ACL > Access Control List Rule; CME batch
modification center: not supported) to add a rule to the ACL.
6. Run the NodeB MML command ADD IPSECPROPOSAL (CME single
configuration: NodeB Configuration Express > IUB_NodeB > IP Transport
Layer > Feature Configuration > IPSecurity > IPSec > IPSec Proposal; CME
batch modification center: not supported) to add an IPsec proposal.
7. Run the NodeB MML command ADD IPSECPOLICY (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > IPSec > IPSec Policy; CME batch modification
center: not supported) to add an IPSec policy.
8. Run the NodeB MML command ADD IPSECBIND (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > IPSec > IPSec Policy Group Binding; CME batch
modification center: not supported) to bind an IPSec policy to a port.
Scenario 4: PSK-based Networking for a NodeB Using Separate Encryption
Figure 303-4 Example of PSK-based networking for a NodeB using separate encryption
The UMTS UMPT provides IPSec for signaling and service data streams on the NodeB,
not for O&M data streams on the NodeB.
1. Run the NodeB MML command SET IKECFG (CME single configuration: NodeB
Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > IKE > IKE Basic Configuration; CME batch
modification center: not supported) to set local IKE configurations.
2. Run the NodeB MML command ADD IKEPROPOSAL (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > IKE > IKE Proposal; CME batch modification
center: not supported) to add an IKE proposal.
3. Run the NodeB MML command ADD IKEPEER (CME single configuration: NodeB
Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > IKE > IKE Peer; CME batch modification center:
not supported) to add an IKE peer.
4. Run the NodeB MML command ADD ACL (CME single configuration: NodeB
Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > ACL > Access Control List; CME batch modification
center: not supported) to add an ACL.
5. Run the NodeB MML command ADD ACLRULE (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > Ipsecurity > ACL > Access Control List Rule; CME batch
modification center: not supported) to add a rule to the ACL.
6. Run the NodeB MML command ADD IPSECPROPOSAL (CME single
configuration: NodeB Configuration Express > IUB_NodeB > IP Transport
Layer > Feature Configuration > IPSecurity > IPSec > IPSec Proposal; CME
batch modification center: not supported) to add an IPsec proposal.
7. Run the NodeB MML command ADD IPSECPOLICY (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > IPSec > IPSec Policy; CME batch modification
center: not supported) to add an IPSec policy.
8. Run the NodeB MML command ADD IPSECBIND (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > IPSec > IPSec Policy Group Binding; CME batch
modification center: not supported) to bind an IPSec policy to a port.
l Verification Procedure
1. Run the NodeB MML command DSP IKESA. Check whether IKE SA data is
displayed in the returned result. If IKE SA data is displayed, go to step 2. If IKE SA
data is not displayed, IPSec fails to be activated.
2. Run the NodeB MML command DSP IPSECSA. Check whether IPSec SA data is
displayed in the returned result. If IPSec SA data is displayed, this feature has been
activated.
3. Run the NodeB MML command LST ACLRULE to check the ACL rules and
determine whether service data is protected by IPSec tunnels. Check whether the
protected services are running normally. For example, if voice services are protected
by IPSec tunnels, place a call to check whether voice services are still running
normally; if management plane packets are protected by IPSec tunnels, check whether
the corresponding NodeB is still online on the topology view of the M2000.
l Deactivation Procedure
1. Run the NodeB MML command RMV IPSECBIND (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > IPSec > IPSec Policy Group Binding; CME batch
modification center: not supported) to remove the binding between an IPSec policy
and a port.
2. Run the NodeB MML command RMV IPSECPOLICY (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > IPSec > IPSec Policy; CME batch modification
center: not supported) to remove an IPSec policy.
3. Run the NodeB MML command RMV IPSECPROPOSAL (CME single
configuration: NodeB Configuration Express > IUB_NodeB > IP Transport
Layer > Feature Configuration > IPSecurity > IPSec > IPSec Proposal; CME
batch modification center: not supported) to remove an IPSec proposal.
4. Run the NodeB MML command RMV ACLRULE (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > Ipsecurity > ACL > Access Control List Rule; CME batch
modification center: not supported) to remove a rule from an ACL.
5. Run the NodeB MML command RMV ACL (CME single configuration: NodeB
Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > ACL > Access Control List; CME batch modification
center: not supported) to remove the ACL.
6. Run the NodeB MML command RMV IKEPEER (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > IKE > IKE Peer; CME batch modification center:
not supported) to remove an IKE peer.
7. Run the NodeB MML command RMV IKEPROPOSAL (CME single configuration:
NodeB Configuration Express > IUB_NodeB > IP Transport Layer > Feature
Configuration > IPSecurity > IKE > IKE Proposal; CME batch modification
center: not supported) to remove an IKE proposal.
----End
Example
//Activation procedure
//Scenario 1: PKI-based Networking for a NodeB Using Unified Encryption
//Adding an IKE proposal
ADD IKEPROPOSAL: PROPID=10, ENCALG=3DES, AUTHALG=MD5,
AUTHMETH=IKE_RSA_SIG, DHGRP=DH_GROUP14, DURATION=86400;
//Adding an IKE peer
ADD IKEPEER: PEERNAME="ike", PROPID=10, IKEVERSION=IKE_V1, EXCHMODE=MAIN,
IDTYPE=IP, REMOTEIP="90.90.90.90", REMOTENAME="secgw", DPD=PERIODIC,
DPDIDLETIME=20, DPDRETRI=4, DPDRETRN=6, LOCALIP="20.20.20.188";
//Adding an ACL
ADD ACL: ACLID=3000, ACLDESC="for IPsec";
//Adding a rule to the ACL
ADD ACLRULE: ACLID=3000, RULEID=1, PT=IP, SIP="32.32.32.1",
SWC="0.0.0.0", DIP="15.15.15.15", DWC="0.0.0.0", MDSCP=NO;
ADD ACLRULE: ACLID=3000, RULEID=2, PT=IP, SIP="30.30.30.1",
SWC="0.0.0.0", DIP="60.60.60.60", DWC="0.0.0.0", MDSCP=NO;
ADD ACLRULE: ACLID=3000, RULEID=3, PT=IP, SIP="30.30.30.1",
SWC="0.0.0.0", DIP="88.88.88.88", DWC="0.0.0.0", MDSCP=NO;
ADD ACLRULE: ACLID=3000, RULEID=4, PT=IP, SIP="30.30.30.1",
SWC="0.0.0.0", DIP="86.86.86.86", DWC="0.0.0.0", MDSCP=NO;
//Adding an IPSec proposal
REPLAYWND=WND_DISABLE;
//Adding the binding between an IPSec policy and a port
ADD IPSECBIND: CN=0, SRN=0, SN=7, SBT=BASE_BOARD, PT=ETH, PN=1,
SPGN="Policy0";
//Verification procedure
DSP IKESA:;
DSP IPSECSA: SN=7, SPGN="Policy0", SPSN=1;
LST ACLRULE:;
//Deactivation procedure
RMV IPSECBIND: SN=7, SBT=BASE_BOARD, PT=ETH, PN=1;
RMV IPSECPOLICY: SPGN="Policy0, SPSN=1;
RMV IPSECPROPOSAL: PROPNAME="prop0";
RMV ACLRULE: ACLID=3000, RULEID=1;
(Optional)RMV ACLRULE: ACLID=3000, RULEID=2;
(Optional)RMV ACLRULE: ACLID=3000, RULEID=3;
(Optional)RMV ACLRULE: ACLID=3000, RULEID=4;
RMV ACL: ACLID=3000;
RMV IKEPEER: PEERNAME="ike";
RMV IKEPROPOSAL: PROPID=10;
304
Frequency point separation between GSM and
Configuring 2.0MHz Central
UMTS mode(UMTS)
This section describes how to activate, verify, and deactivate the optional feature MRFD-221703
2.0MHz Central Frequency point separation between GSM and UMTS mode(UMTS).
Prerequisites
l Dependencies on Hardware
MRFU and RRU3908 of V2 or later versions support the feature.
UMTS:900M MRRU, 900M MRFU (excluding V1), 850M MRRU V2.
l Dependencies on Other Features
GBFD-114801 Discontinuous Transmission (DTX) Downlink
GBFD-117601 HUAWEI III Power Control Algorithm
GBFD-117602 Active Power Control
MRFD-211703 2.0 MHz Central Frequency Point Separation Between GSM and UMTS
Mode (GSM)
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Other Prerequisites
GSM and UMTS Dynamic Power Sharing is not supported in GSM dynamic transmit
diversity.
It is not recommended that GSM and UMTS Dynamic Power Sharing coexist with the
baseband frequency hopping algorithm involving two power amplifiers because their
coexistence would result in a certain level of performance loss.
GSM and UMTS Dynamic Power Sharing in MIMO is not recommended.
It needs to purchase professional service additionally to minimize the KPI losses.
Context
This feature improves frequency utilization. It enables the UMTS carriers to use the bandwidth
3.8 MHz and therefore increase the capacity of the GSM network.
Procedure
l Activation Procedure
1. Run the NodeB MML command SET FREQBWH (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Device Panel > RUX Topology >
Right click RRU > RXU Board Property > Radio Frequency Unit; CME batch
modification center: not supported) to set the minimal frequency bandwidth on the
UMTS side. In this step, set Frequency Min Bandwidth to 3800.
2. To ensure that the UMTS carrier bandwidth is 3.8 MHz and the frequency spacing
between GSM and UMTS carriers is 2.0 MHz, as set in step 1, do as follows to modify
frequency points on the GSM or UMTS side:
Modify the UMTS carrier Central Frequency Point
a. Run the BSC6900 MML command DEA UCELL (CME single
configuration: UMTS Cell Configuration Express > Cell Basic
Information > Cell Basic Information. Set Validation indication to
Deactivated; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches) to deactivate a cell.
b. Run the BSC6900 MML command MOD UCELLSETUP (CME single
configuration: UMTS Cell Configuration Express > Cell Basic
Information > Cell Basic Information; CME batch modification center:
3.18 Modifying UMTS Cell Parameters in Batches). In this step, modify
frequency points for UMTS cells at the BSC6900. Set Band Indicator, UL
Frequency Ind, Uplink UARFCN and Downlink UARFCN.
c. Run the NodeB MML command MOD LOCELL (CME single
configuration: NodeB Configuration Express > IUB_NodeB > Radio
Layer > xx Sector > Locell; CME batch modification center: 3.17 Modifying
Physical NodeB Parameters in Batches) to modify some properties of a
local cell. In this step, set UL Frequency Channel Number and DL
Frequency Channel Number.
d. Run the BSC6900 MML command ACT UCELL (CME single
configuration: UMTS Cell Configuration Express > Cell Basic
Information > Cell Basic Information. Set Validation indication to
Activated; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches) to activate a cell.
Modify the GSM central frequency point separation
a. Run the BSC6900 MML command MOD GTRX (CME single configuration:
BTS Topology > Right click Cell > Configure TRX Frequency; CME
batch modification center: not supported) to modify the frequency of a TRX.
In this step, set Frequency to ensure that the frequency spacing between GSM
and UMTS carriers is 2.0 MHz.
l Verification Procedure
1. Run the NodeB MML command LST FREQBWH to check whether the UMTS
carrier bandwidth is 3.8 MHz.
2. Check on the NodeB side whether all TRXs work properly when the frequency spacing
between GSM and UMTS carriers is 2.0 MHz.
3. Check on the BSC side whether services in all cells are normal when the frequency
spacing between GSM and UMTS carriers is 2.0 MHz.
l Deactivation Procedure
1. Run the NodeB MML command SET FREQBWH (CME single configuration:
NodeB Configuration Express > IUB_NodeB > Device Panel > RUX Topology >
Right click RRU > RXU Board Property > Radio Frequency Unit; CME batch
modification center: not supported) to set the UMTS carrier bandwidth. The UMTS
carrier bandwidth should range from 4.2 MHz to 5.0 MHz.
2. To ensure that the UMTS carrier bandwidth is the bandwidth set in step 1, do as follows
to modify frequency points on the GSM or UMTS side:
Modify the UMTS central frequency point separation
a. Run the BSC6900 MML command DEA UCELL (CME single
configuration: UMTS Cell Configuration Express > Cell Basic
Information > Cell Basic Information. Set Validation indication to
Deactivated; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches) to deactivate a cell.
b. Run the BSC6900 MML command MOD UCELLSETUP (CME single
configuration: UMTS Cell Configuration Express > Cell Basic
Information > Cell Basic Information; CME batch modification center:
3.18 Modifying UMTS Cell Parameters in Batches). In this step, modify
frequency points for UMTS cells at the BSC6900 and set Band Indicator,
UL Frequency Ind and Downlink UARFCN.
c. Run the NodeB MML command MOD LOCELL (CME single
configuration: NodeB Configuration Express > IUB_NodeB > Radio
Layer > xx Sector > Locell; CME batch modification center: 3.17 Modifying
Physical NodeB Parameters in Batches) to modify some properties of a
local cell. In this step, set UL Frequency Channel Number and DL
Frequency Channel Number.
d. Run the BSC6900 MML command ACT UCELL (CME single
configuration: UMTS Cell Configuration Express > Cell Basic
Information > Cell Basic Information. Set Validation indication to
Activated; CME batch modification center: 3.18 Modifying UMTS Cell
Parameters in Batches) to activate a cell.
Modify the GSM central frequency point separation
a. Run the BSC6900 MML command MOD GTRX (CME single configuration:
BTS Topology > Right click Cell > Configure TRX Frequency; CME
batch modification center: not supported) to modify the frequency of a TRX.
In this step, set Frequency to ensure that the frequency spacing between GSM
and UMTS carriers no less than 2.2 MHz.
----End
Example
//Activation procedure
//Setting the UMTS carrier bandwidth to 3.8 MHz
SET FREQBWH: CN=0, SRN=4, SN=0, FMBWH=3800;
//Setting the uplink and downlink frequencies of a UMTS cell to 2815 and
3040
DEA UCELL: CellId=101;
MOD UCELLSETUP: CellId=101, BandInd=Band8, UARFCNUplinkInd=FALSE,
UARFCNDownlink=3040;
MOD LOCELL: LOCELL=101, SECT=LOCAL_SECTOR, ULFREQ=2815, DLFREQ=3040;
ACT UCELL: CellId=101;
//Setting the uplink and downlink frequencies of a UMTS cell to 2821 and
3046
DEA UCELL: CellId=101;
MOD UCELLSETUP: CellId=101, BandInd=Band8, UARFCNUplinkInd=FALSE,
UARFCNDownlink=3046;
MOD LOCELL: LOCELL=101, SECT=LOCAL_SECTOR, ULFREQ=2821, DLFREQ=3046;
ACT UCELL: CellId=101;
This section describes how to activate, verify, and deactivate the multi-mode feature
MRFD-221803 Dynamic MA for GU Dynamic Spectrum Sharing(UMTS).
Prerequisites
l Dependencies on Other Features
The following features have been configured before this feature is activated:
MRFD-221802 GSM and UMTS Dynamic Spectrum Sharing(UMTS).
This feature cannot be used together with MRFD-211703 2.0MHz Central Frequency
point separation between GSM and UMTS mode(GSM) and MRFD-221703 2.0MHz
Central Frequency point separation between GSM and UMTS mode(UMTS).
The feature must be used together with the feature MRFD-211803 Dynamic MA for
GU Dynamic Spectrum Sharing (GSM).
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
l Requirements for the Operating Environment
The M2000 is of the V200R011 version.
A common M2000 configuration is required.
Context
After this feature is activated, the BSC starts spectrum sharing when the traffic volume of a cell
is lighter than what can be carried on two or three TRXs, increasing the spectrum sharing time.
Operators are advised to enable this feature in the scenario where the GSM and UMTS Dynamic
Spectrum Sharing feature is enabled.
l Precautions
After this feature is activated, dynamically changing an absolute radio frequency
channel number (ARFCN) of a cell leads to cell reset.
This feature affects the following algorithms:
Procedure
l Activation Procedure
1. Run the BSC6900 MML command ADD GCELLMAGRP (CME single
configuration: BTS Topology > Cell > Configure MA Group; CME batch
modification center: not supported) to add the mobile allocations (MAs) before and
after dynamic spectrum sharing is enabled.
2. Run the BSC6900 MML command SET GTRXCHANHOP (CME single
configuration: BTS Topology > Cell > Configure MA Group; CME batch
modification center: not supported). In this step, set FH Index Used After Frequency
Spectrum Sharing and MAIO Used After Frequency Spectrum Sharing for the
channels in the cell.
l Verification Procedure
1. Check that this feature has taken effect by viewing the value of the Number of dynamic
MA changing requests counter.
l Deactivation Procedure
1. Run the BSC6900 MML command SET GTRXCHANHOP (CME single
configuration: BTS Topology > Cell > Configure MA Group; CME batch
modification center: not supported). In this step, set FH Index Used After Frequency
Spectrum Sharing to 255.
----End
Example
/*Activation procedure*/
//GSM and UMTS Dynamic Spectrum Sharing must have been configured before
//Deactivation procedure
SET GTRXCHANHOP: TRXID=1001, CHNO=0, TRXHOPINDEX=1, TRXMAIO=0,
IDTYPE=BYID, TRXDSSHOPINDEX=255, TRXDSSMAIO=0;
SET GTRXCHANHOP: TRXID=1001, CHNO=1, TRXHOPINDEX=1, TRXMAIO=0,
IDTYPE=BYID, TRXDSSHOPINDEX=255, TRXDSSMAIO=0;
This section describes how to activate, verify, and deactivate the multi-mode feature
MRFD-221804 GSM Power Control on Interference Frequency for GU Small Frequency gap
(UMTS).
Prerequisites
l Requirements on Hardware
Only 3900 series base stations support this feature.
l Dependencies on Other Features
The feature GBFD-113701 Frequency Hopping (RF hopping, baseband hopping) has
been configured before this feature is activated.
MRFD-221703 2.0MHz Central Frequency point separation between GSM and UMTS
mode (UMTS) or WRFD-021001 Flexible frequency bandwidth of UMTS.
The feature must be used together with MRFD-211804 GSM Power Control on
Interference Frequency for GU Small Frequency gap (GSM).
l License
The license controlling this feature has been activated. For details on how to activate
the license, see 4 Activating the UMTS License. For details about license items, see
2 Feature Activation and License Item Descriptions.
Context
This feature is recommended for the GU refarming 3.8 MHz or 4.2 MHz scenario where the
number of FH TCH frequencies is greater than or equal to 6.
l Precautions
The interfering frequencies must join in FH.
Operators are not advised to enable this feature together with the feature MRFD-211801
Multi-mode Dynamic Power Sharing(GSM) or MRFD-221801 Multi-mode Dynamic
Power Sharing(UMTS).
This feature affects the following features: GBFD-117002 IBCA (Interference Based
Channel Allocation), GBFD-118106 Dynamic Power Sharing, GBFD-113201
Concentric Cell, GBFD-115507 WB AMR, and GBFD-115830 VAMOS.
l Data Preparation
When this feature is used together with the feature 2.0MHz Central Frequency point
separation between GSM and UMTS mode, operators only need to prepare the data for
the feature 2.0MHz Central Frequency point separation between GSM and UMTS
mode.
When this feature is used together with the function GU Refarming 4.2 MHz of the
Flexible Frequency Bandwidth of UMTS Carrier feature, the data for this feature is the
same as the data for the function GU Refarming 4.2 MHz.
The following table describes the parameters that are specific to this feature.
Paramet Parame Description Data Source
er Name ter ID
Procedure
l Activation Procedure
1. Run the BSC6900 MML command SET GCELLNONSTANDARDBW (CME
single configuration: Cell Configuration Express > Power Control > GSM/UMTS
Small Frequency Spacing Interference Control Parameters; CME batch
modification center: Modifying GSM Cell Parameters in Batches). In this step, set
Frequency-based Power Control to ON and set the other parameters to appropriate
values. The other parameters are Cell Index, Interference Coordination Policy,
GU2.0 MHz Max. Power Decrease for Interfering Frequency, GU2.2 MHz Max.
Power Decrease for Interfering Frequency, UMTS Center Frequency 1, UMTS
Center Frequency 2, Non-AHR Power Compensation Proportion, Non-AHR
l Deactivation Procedure
1. Run the BSC6900 MML command SET GCELLNONSTANDARDBW (CME
single configuration: Cell Configuration Express > Power Control > GSM/UMTS
Small Frequency Spacing Interference Control Parameters; CME batch
modification center: Modifying GSM Cell Parameters in Batches). In this step, set
Frequency-based Power Control to OFF.
----End
Example
/*Activation procedure*/
SET GCELLNONSTANDARDBW: IDTYPE=BYID, CELLID=2, GUDegratePwrCtrl=ON,
GUDegratePwrPri=GSM, GU2000KHzMaxVal=10, GU2200KHzMaxVal=3,
UMTSFreqNum1=0, UMTSFreqNum2=0, NAHRCompCoeff=5, NAHRCompOffVal=-15,
AHRCompCoeff=5, AHRCompOffVal=-15;
/*Deactivation procedure*/
SET GCELLNONSTANDARDBW: IDTYPE=BYID, CELLID=2, GUDegratePwrCtrl=OFF;