PROBLEM 2.25
esa Link BD is made of ass (£ = 108 GPa) and as a cross-sectional aea of
c[k C= sade of unin (2 = 72 GP) a so cos
. ‘Scotioual area of 300 mun". Knowing that they support rigid member 48C,
{determine the minum force P that ean be applied vertically at point if
Istlon qs deflaction of isnot to excasd 0.35 mam.
PROBLEM 2.26
Members 42C and DEF are joined with steel links (E = 200 GPa).
Each of the links is made of a pair of 25 » 3Snm plates. Determine
the change in length of (a) member BE. (8) member CF
PROBLEM 2.27
Each ofthe links 4B and CD is made of aluminum (E = 75 GPa) and has
‘2 cross-sectional area of 258 mm. Knowing that they support the rigid
member BC, determine the defletion of point
PROBLEM 2.29
“Aliomogensous cable of length Zand uniform cross section is suspended from one end. (a) Denoting by pthe
density (anass per unit volume) ofthe cable and by £ its modulus of elasticity. determine the elongation of the
cable due fo its own weight. (2) Show thatthe same elongation would be obtained ifthe cable were horizontal
and if a force equal te alf of is weight were applied at each end.
(2.35. The 1.35 m concrete post is reinforced with six steel bars, each with a
28 mm diameter. Knowing that E, = 200 GPa and E, = 29 GPa,
determine the normal stresses in the steel and in the concrete when a
1560 kN axial conti ore Pis applied tothe post.Sam PROBLEM 2.37
‘An axial force of 200 EN is applied to the assembly shown by means of
gid end plates. Determine (a) the normal stress in the aluminum shell,
(B) the corresponding deformation ofthe assembly.
eo
Alisha
che
PROBLEM 2.39
A polystyrene rod consisting of two cylindrical potions 4B and BC is restrained at
WIN both ends and supports twa 30-KN loads as shown. Knowing that E3.1GPa,
determine (¢) the reactions at 4 and C. (6) the normal stress in each portion ofthe
rad,
e250
Diners nm PROBLEM 2.41
‘Two oplindrca rods, one of ste! and the or of bras, re jinsd at
‘Cand restrained by rigid supports at 4 and £, For the loading shown
‘and Knowing that E,=200 GPa and £, =105 GPa, detemine
(the reactions at and E, (the deletion of point C:
{0-0 dam
A “PROBLEM 2.43
aw wl eat ae 2 nd CE mad tg = 105 GP)
: NT andi cessostonl area of 200 mn. tein the
‘ deflection of end ofthe rigid member ABC caused by the
BRN Toad
PROBLEM 2.51
A rod consisting of to eplindtisal portions 4B and BC is restrained a both
ends, Portion 4B is made of tel (E, =200 GPa, @, =11.7 10°C) and
postion BC is mde of bss (Z, =105 GPa, ay =20.9»10-*/°C), Knowing
‘har the 10d is intially uaswessed, determine the compressive force induced in
ABC when there is. temperate tse of S0°C.. PROBLEM 2.53,
ee Solve Problem 2.52, assuming that portion AB f the composite rod is
‘made of stel and portion BC is made of brass.
' b PROBLEM 2.52 A rod consisting of tw eylindrical portions 42 and BC
L tonnsmaser is restained at both ends. Portion AB is made of brass (Ey =105 GPa,
910°C) and portion BC is made of aluminum (E, =72 GPa,
9x10%7C). Knowing that the rod is initally ‘unstressed.
determine (a) the normal stresses induced in portions AB and BC by a
‘temperature rise of 42°C, (6) the cortesponding deflection of point B.
Cio spain —j PROBLEM 2.58
Knowing that a 0.5.mm gap exists when the temperature is 24°C,
deiermine (a) the temperature at which the normal stress in the
‘aluminum bar will be equal to ~75 MPa, (b) the corresponding exact
hin length of the aluminum bar.
Hx 10 wre
«amp PROBLEM 2.69
ett A an se wa don hs fa tel pose
a E vessel. After pressurization, the biaxial sess condition atthe square
one Se! Nm isa shown. For £ =200 GPa and »=0.30, determine the change in
= tr length of (a) side AB, (b) side BC, (c) diagnonal AC.
%
“a
PROBLEM 2.70
The block shown is made ofa magnesium alloy. for which
E=48 GPa and ¥=0.38. Knowing that 2, =—180 MPa,
determine (2) the mgaitue of ¢, for which the change in
the height of the block willbe zero, (0) the coresponding
chnge inthe aea ofthe fae ABCD. () the comespondin
‘thang inthe valine ofthe block.
PROBLEM 2.75
“The plastic block shown is bonded to a rigid support and to vertical plate to
which a 240-4N load P is applied. Knowing that for the plastic used
1050 MPa, determine the deflection ofthe plateA
Lot
PROBLEM 2.81
_A vibration isolation unit consists of rwo blocks of hard subber bonded
fo 4 plate 4 and to rigid supports as shown. Knowing that a foree of
magnitude P= 25KN causes a deflection = 1.5mm. of plate 43,
‘determine the modulus of rigidity ofthe rubber used,