Professional Documents
Culture Documents
Abtech Atex Reference Guide PDF
Abtech Atex Reference Guide PDF
Zone 0 CENELEC Classification EN 6007910 Division 1 US Classification ANSI/INFPA70 NEC Article 500
IEC Classification IEC 60 07910
ATEX Classification ATEX Directive 94/9/EC explosive
US Classification ANSI/INFPA70 NEC Article 505 Intermittent atmosphere is
Zone 1 / Zone 21
hazard Division 1 likely to occur in
normal operation
Explosion Protection Concepts Explosion Protection Concepts
Basic Concept of Typical Gas IEC/EN Typical explosive Type of Code Basic concept of Typical Applicable
Type of Protection Symbol Class
Protection Zone(s) Group Standard IEC EPL atmosphere is Protection protection Division / Zone Standard
Hazard under
Protection of Electrical Equipment for Gases and Vapours G unlikely to occur
abnormal Zone 2 / Zone 22
Division 2 but if it does, will Protection of Electrical Equipment for Gases and Vapours Class I
Flameproof d 1,2 600791 Gb conditions
Contain the exist only for a
II Flameproof AEx d Class 1 Zone 1, 2 ISA 600791
Enclosed Break nC explosion 2 6007915 Gc short period Contain the
Explosion proof XP Class 1 Division 1 UL1203
explosion
Increased Safety e No arcs, sparks or 1, 2 600797 Gb Enclosed Break AEx nC Class 1 Zone 2 ISA 6007915
hotsurfaces. II Equipment intended for use in zone 1 areas cannot be used in Division 1 areas as this Increased Safety AEx e Class 1 Zone 1, 2 ISA 600797
Non Sparking nA Enclosure IP54 2 6007915 Gc covers zone 0 rated areas also. No arcs, sparks or
Non Sparking AEx nA Class 1 Zone 2 ISA 6007915
ia 0, 1, 2 Ga hot surfaces
limit circuit energy Non Incendive NI Class 1 Division 2 ISA 12.12.01 / FM3611
Intrinsic Safety ib 1, 2 II 6007911 Gb Sand Filled AEx q Quench the flame Class 1 Zone 1, 2 ISA 600795
and hot surfaces
ic 2 Gc AEx ia Class 1 Zone 0, 1, 2
ma 0, 1, 2 Ga Comparison of IP and NEMA Enclosure Ratings Intrinsic Safety AEx ib
Limit circuit
Class 1 Zone 1, 2
ISA 6007911
Encapsulation mb 1, 2 6007918 Gb energy and hot
IS Class 1 Division 1 UL913 / FM3610
mc 2 Gc Enclosure surfaces
IP23 IP30 IP32 IP55 IP64 IP65 IP66 IP67 Limited Energy AEx nC Class 1 Zone 2 ISA 6007915
Sealed/Hermetic Sealing nC 2 Gc Type
6007915 AEx m Class 1 Zone 1, 2
Restricted Breathing nR Exclude fuel 2 II Gc 1 Encapsulation AEx ma Class 1 Zone 0, 1, 2 ISA 6007918
Oil Filled o 1, 2 600796 Gb 2 AEx mb Class 1 Zone 1, 2
px 1, 2 Gb Oil Filled AEx o Class 1 Zone 1, 2 ISA 600796
Pressurised py 1, 2 600792 Gb 3 Type X Class 1 Division 1
pz 2 Gc 4 Type Y Class 1 Division 1 NFPA 496 / FM3620
Exclude fuel
Sand Filled q Quench the flame 1, 2 II 600795 Gb 4X Pressurised
Type Z Class 1 Division 2
OP sh 0, 1, 2 Ga AEx px Class 1 Zone 1
Optical Radiation Op is Inherently safe 0, 1, 2 II 6007928 Ga
6 AEx px Class 1 Zone 1 ISA 600792
Op pr 1, 2 Gb 12 AEx px Class 1 Zone 2
Protection of Electrical Equipment for Combustible Dusts D 13 Restricted
AEx nR Class 1 Zone 2 ISA 6007915
This comparison is for guidance only. It is the responsibility of the user to ensure the Breathing
ta 20, 21, 22 Da
Exclude dusts by enclosure rating is suitable for the given application. Protection of Electrical Equipment for Combustible Dust Class II & III
Enclosure tb 21, 22 III 6007931 Db
use of enclosure
tc 21, 22 Dc Dust Ignition DIP Class II Division 1 & 2 UL1203
iaD Use of enclosure 20, 21, 22 Da Proof
Intrinsic Safety ibD and energy 21, 22 III 6124111 Db Dust Protected NI Exclude Class II Division 2 ISA 12.12.01 / FM3611
icD limitation 21, 22 Dc Temperature Classification Protection by AEx tD combustible dust Class II Zone 2
ISA 6007931
ma 20, 21, 22 Da Enclosure
Encapsulation mb Exclude dust 21, 22 6007918 Db Max Surface Max Surface AEx maD Zone 20, 21, 22
ATEX/IEC* NEC 505 NEC 500 Encapsulation ISA 6124118
mc 21, 22 Dc Temperature Temperature
AEx mbD Zone 21, 22
450C T1 T1 T1 450C AEx iaD Zone 20, 21, 22
General requirements Covers application and testing related to above protection methods Limit circuit ISA 6124111
300C T2 T2 T2 300C Intrinsic Safety AEX ibD energy and hot Zone 21, 22
T2A 280 C IS surfaces Class II Division 1
UL 913 / FM3610
Typical ATEX and IEC Ex Equipment Marking IS Class III Division 1
T2B 260 C
T2C 230 C Typical NEC Equipment Marking
Ex II 2 G Ex e IIC T4 Gb T2D 215 C
200C T3 T3 T3 200C NEC 500 NEC 505
T3A 180 C
Group
T3B 165 C Class 1 Division 1 T3 Class 1 Zone 1 AEx d IIC T3
A,B,C
Equipment Protection
explosion protection*
T3C 160 C
Equipment Category*
Explosion Protection
Specific marking for
Equipment Group*
Temperature Class
Type of Protection
135C T4 T4 T4 135C
Environment*
T4A 120 C
Gas Group
100C T5 T5 T5 100C
Protection Concept
American Standard
Temperature Class
Temperature Class
Permitted Division
85 T6 T6 T6 85
Level
Permitted Class
Permitted Zone
Permitted Class
*For ATEX/IEC applications applies to Group II gases only. Group 1 applications have different classifications
Gas Group
Gas Group
For ATEX certified equipment, the CE mark should be shown, along with the relevant Notified Body number, where applicable.
*Required for ATEX only
ABTHX2011