Professional Documents
Culture Documents
SAFETY NEEDED
GOGGLES
GLOVES
NO LOOSE CLOTHING
EXTRA PERSON FOR CONSTRUCTION
DO NOT: USE THE SWING FRAME FOR ANYTHING OTHER THAN ITS INTENDED PURPOSE; ALTER THE FRAME;
OR ENGAGE MORE THAN 225LBS ON SWING. SWING MUST BE ANCHORED TO THE GROUND.
PARENTAL SUPERVISION REQUIRED FOR CHILDREN UNDER 10 YEARS OF AGE.
CAUTION: The instructions are only a guide, and should be followed by individuals familiar with home building projects. Spike TV and Producer assume no responsibility,
and are not liable for any injuries or damages due to reliance on instructions. Parental supervision recommended for individuals under 18. Use at your own risk.
STEP ONE: DISASSEMBLE PALLETS
Using a reciprocating saw, disassemble the pallets.
CAUTION: The instructions are only a guide, and should be followed by individuals familiar with home building projects. Spike TV and Producer assume no responsibility,
and are not liable for any injuries or damages due to reliance on instructions. Parental supervision recommended for individuals under 18. Use at your own risk.
STEP THREE: BUILD FRAME
Build a basic 2 x 4 frame with two 48 2 x 4s and
four 16 2 x 4s, spaced 16 on center.
A. Your sides will the two 48 pieces, ribbed with the
16 ones.
CAUTION: The instructions are only a guide, and should be followed by individuals familiar with home building projects. Spike TV and Producer assume no responsibility,
and are not liable for any injuries or damages due to reliance on instructions. Parental supervision recommended for individuals under 18. Use at your own risk.
STEP FIVE:
Attach the back seat boards to the back supports using 1 wood screws, be sure to
off set the screws to add strength.
STEP SIX:
CAUTION: The instructions are only a guide, and should be followed by individuals familiar with home building projects. Spike TV and Producer assume no responsibility,
and are not liable for any injuries or damages due to reliance on instructions. Parental supervision recommended for individuals under 18. Use at your own risk.
STEP SEVEN:
Attach the back and front arm supports.
STEP EIGHT:
Attach the top of the arm rest to the supports by pre drilling and using 1 5/8
wood screws.
STEP NINE:
The eyebolt should be inserted on the top of the front of the left and right arms of the swing and the back of the left
and right arm. Attach the eyebolt to the arms of the swing a few inches from each end and in the center. Drill a hole
that is slightly smaller than the diameter of the eyebolt's threaded end. Take the threaded end of the eyebolt and
insert it into the hole. Turn the eyebolt by placing a screwdriver into the "eye" and turning it until the only thing you
see is the eye firmly against the wood. Make sure that there is an equal distance between the two eyebolts.
CAUTION: The instructions are only a guide, and should be followed by individuals familiar with home building projects. Spike TV and Producer assume no responsibility,
and are not liable for any injuries or damages due to reliance on instructions. Parental supervision recommended for individuals under 18. Use at your own risk.
STEP TEN :
Assemble swing frame according to the manufacturers directions
STEP ELEVEN :
Attach swing to swing frame according to the manufacturers directions
CAUTION: The instructions are only a guide, and should be followed by individuals familiar with home building projects. Spike TV and Producer assume no responsibility,
and are not liable for any injuries or damages due to reliance on instructions. Parental supervision recommended for individuals under 18. Use at your own risk.
PALLET PATIO SET
SAFETY NEEDED
Goggles
Gloves
Backbrace (helpful when lifting)
STEP ONE:
Align one pallet on top of another and in each corner, using 1 screws, secure through the adjoining slats
STEP TWO:
Now measure the width of your pallets and cut a 2 x 4 to that length
STEP THREE:
Affix the 2 x 4 with 1 screws underneath the top slats at the distance of your desired seat back
STEP FOUR:
Take another pallet and measure 19 into the middle on each side. Connect the line.
Repeat on the opposing side
STEP FIVE:
5. Run the circular saw down each of these lines, cutting your pallet into three pieces.
The two 19 lengths will your seat backing. Discard the third
STEP SIX:
Take your two seat backs and measure their length.
STEP SEVEN:
Cut a 2 x4 to length, and on open end of the seat back pieces, insert and attach
your 2 x 4, using the 1 screws.
STEP EIGHT:
Position the seat back above the 2 x 4 you affixed in step three, with the 2 x 4
end of the seat back facing down.
STEP NINE:
Attach the seat back using 4 SDS screws
STEP TEN:
Attach four casters in each corner of the bottom pallet.
FOR COUCH
Repeat steps above twice to make two separate chairs
Scab them together using a 2 1 x 3 on the front and back insides of the pallet
(Scab means using one piece of wood, attaching it to 2 other pieces of wood to form one continuous piece.)
FOR TABLE
Repeat steps 1-3 above
Attach four casters in each corner of the bottom pallet.
STEP ELEVEN: SHARE YOUR WORK!
Snap a photo or shoot or shoot a video of your completed work and it might get shown on the live show!
twitter.com/BuildStuffLive
instagram.com/BuildStuffLive
facebook.com/BuildStuffLive
Whatever platform you choose to post on, be sure to use the hashtag:
#BuildStuffLive