Professional Documents
Culture Documents
Alcatel-Lucent 9370
Radio Network Controller | UA08.1
RNC Commissioning Method
24-3005
Issue 3.01 | October 2012
Legal notice
Legal notice
Alcatel, Lucent, Alcatel-Lucent and the Alcatel-Lucent logo are trademarks of Alcatel-Lucent. All other trademarks are the property of their respective
owners.
The information presented is subject to change without notice. Alcatel-Lucent assumes no responsibility for inaccuracies contained herein.
Copyright 2012 Alcatel-Lucent. All rights reserved.
Trademarks
"Nortel Multiservice Switch", "Nortel Multiservice Data Manager", "Nortel Point of Concentration" are Nortel products.
Contents
2 Material requirements
....................................................................................................................................................................................................................................
Preparations ................................................................................................................................................................................. 3-3
3-3
C LED display
D Glossary
....................................................................................................................................................................................................................................
iv Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
Contents
....................................................................................................................................................................................................................................
E Report sheet
Index
....................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC v
24-3005 UA08.1
Issue 3.01 October 2012
Contents
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
vi Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
List of tables
....................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC vii
24-3005 UA08.1
Issue 3.01 October 2012
List of tables
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
viii Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
List of figures
1-8 9370 RNC dimensioning with CP4 for DCPS ................................................................................................ 1-7
1-9 9370 RNC dimensioning with CP4 for eDCPS .............................................................................................. 1-7
4-2 Breakers Interface Panel (BIP) of the 9370 RNC .......................................................................................... 4-5
4-3 Alarm LED Status Indicators for BIM Modules ............................................................................................ 4-6
4-4 Laptop connection with the 9370 RNC CP card ............................................................................................ 4-7
....................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC ix
24-3005 UA08.1
Issue 3.01 October 2012
List of figures
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
x Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
About this document
About this document
Purpose
The purpose of this document is used to describe the on-site operations to be carried out
to commission Alcatel-Lucent 9370 RNC cabinet. There are two families of the 9370
RNCs:
9370 RNC-SDH: the 9370 RNC provides only optical interfaces (OC3/STM1).
9370 RNC-PCM: the 9370 RNC provides electrical PCMs interfaces.
Intended audience
The audience for this document is Installation personnel and Commissioning personnel.
...................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC xi
24-3005 UA08.1
Issue 3.01 October 2012
About this document
....................................................................................................................................................................................................................................
Supported systems
This document applies to Alcatel-Lucent W-CDMA UA08.1 system release.
This document applies to Alcatel-Lucent 9370 RNC.
Prerequisites
It is recommended that readers become familiar with 3rd Generation Partnership Project
(3GPP) Technical Specification release 99 (R99) and the UMTS specifications.
Conventions used
Vocabulary conventions
None
Typographical conventions
The following typographical conventions are used in this document:
Appearance Description
italicized text File and directory names
Emphasized information
IP reference, reference number Related document that is referenced in the
document
Related information
For information on subjects related to the content of this document, refer to the
documents listed in the following table:
....................................................................................................................................................................................................................................
xii Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
About this document
....................................................................................................................................................................................................................................
Document support
For support in using this or any other Alcatel-Lucent document, contact Alcatel-Lucent at
one of the following telephone numbers:
1-888-582-3688 (for the United States)
1-630-224-2485 (for all other countries)
Technical support
For technical support, contact your local Alcatel-Lucent customer support team. See the
Alcatel-Lucent Support web site (http://www.alcatel-lucent.com/support/) for contact
information.
How to order
To order Alcatel-Lucent documents, contact your local sales representative or use Online
Customer Support (OLCS) (http://support.alcatel-lucent.com)
How to comment
To comment on this document, go to the Online Comment Form (http://infodoc.alcatel-
lucent.com/comments/) or e-mail your comments to the Comments Hotline
(comments@alcatel-lucent.com).
....................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC xiii
24-3005 UA08.1
Issue 3.01 October 2012
About this document
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
xiv Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
1 Introduction to 9370 RNC
1
Overview
Purpose
This chapter provides a brief description of the the 9370 RNC in terms of hardware
compatibility conditions, IP transport evolution, supported cards, market models, and
capacity.
Contents
...................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC 1-1
24-3005 UA08.1
Issue 3.01 October 2012
Introduction to 9370 RNC 9370 RNC compatibility matrix
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
1-2 Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
Introduction to 9370 RNC 9370 RNC compatibility matrix
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC 1-3
24-3005 UA08.1
Issue 3.01 October 2012
Introduction to 9370 RNC 9370 RNC compatibility matrix
....................................................................................................................................................................................................................................
Table 1-1 Hardware compatibility (continued)
All RNC interfaces were transported as ATM on Sonet OC3 (or ATM on SDH STM1) till
UA5.2 release.
The ATM user-plane transport used the following transport layers and protocols:
ATM-AAL2/Sonet (SDH) for IuB, IuR, and IuCS
IP/ATM-AAL5/Sonet (SDH)4 for IuPS
The ATM control-plane traffic was a mix of AAL5 (NBAP) and SS7 stacks both also
being carried on ATM-AAL5 /Sonet (SDH).
Release UA06 introduced Hybrid IuB and IuPS on IP/GE. For hybrid IuB, HSPA user
plane traffic was routed as UDP/IP/GE, whereas other user-plane traffic (voice and other
low bandwidth traffic) remained on ATM-AAL2/Sonet (SDH). All the IuB control-plane
traffic remained on the ATM/Sonet (SDH) transport. With UA06, in addition to the ATM
transport for IuPS, all user-plane and control-plane traffic could alternately be transported
over IP/GE.
....................................................................................................................................................................................................................................
1-4 Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
Introduction to 9370 RNC 9370 RNC compatibility matrix
....................................................................................................................................................................................................................................
Release UA07.1 introduced the support for IP/GE for the IuCS, IuR, and IuB (native IP
IuB) interfaces. With this release, it was possible to use hybrid (ATM and IP) connections
on the same RNC for any Iu interface.
IuB - An RNC can connect simultaneously to a NodeB with ATM-only connections, a
NodeB with hybrid (ATM and IP) connections, and a NodeB with IP-only
connections.
IuR - An RNC may have some neighboring RNC with ATM IuR connections and
others with IP IuR connections. Although a single RNC can support both ATM and IP
IuR connections, all connections between any two RNCs have to be either ATM or IP
based.
IuPS - Using IuFlex, an RNC can connect simultaneously to one (or more) SGSN
core with ATM connections and one (or more) other SGSN with IP/GE connections.
IuCS - Using IuFlex, an RNC can connect simultaneously to one (or more) MSC with
ATM/Sonet (SDH) connections and other MSC with IP/ GE connections.
With the introduction of IP IuB, IuCS, IuR, and continued support for IuPS, it is now
possible to deliver an All IP UTRAN RNC. Replacement of two 16P OC3 (STM1) FP
cards with two Packet Server (PS) cards facilitates proportional growth in RNC capacity
from 10 to 12 PS cards.
....................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC 1-5
24-3005 UA08.1
Issue 3.01 October 2012
Introduction to 9370 RNC 9370 RNC compatibility matrix
....................................................................................................................................................................................................................................
Market models
The following tables show UA06/UA07/UA08 RNC market models and associated
NodeBs/Cells dimensioning.
....................................................................................................................................................................................................................................
1-6 Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
Introduction to 9370 RNC 9370 RNC compatibility matrix
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC 1-7
24-3005 UA08.1
Issue 3.01 October 2012
Introduction to 9370 RNC 9370 RNC compatibility matrix
....................................................................................................................................................................................................................................
Explanation: Each service group (SG) supports a maximum number of 144 cells,
which depends on the number of TMUs configured. For example, if the RNC is
equipped with 10 eDCPS cards and we have 12 TMUs (with 10 SGs), then the RNC
can manage a maximum of 1440 cells. Once ServiceGroup*144 crosses 2400-cell
mark on a RNC containing 10 eDCPS boards, the maximum number of cells managed
by the RNC in this configuration will be limited to 2400 cells.
Note: When the eDCPS Capacity Increase feature is not activated, an RNC equipped
with 10 eDCPS boards can support 2400 cells. For example, If the number of TMUs
is 14, then number of managed cells will be 2400; (12 SG * 204 2400 cells).
The number of service groups supported is described in the following table:
Notes:
1. * = Not supported when eDCPS capacity increase feature is activated.
Note: The values listed above are default values and used for commissioning purpose
only. In case of 10 and 12 eDCPS configurations, the actual number of service groups
are set based on the required configuration and capacity.
Module type
The following table provides the supported modules for the 9370 RNC and the relevant
card type for these modules:
....................................................................................................................................................................................................................................
1-8 Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
Introduction to 9370 RNC 9370 RNC compatibility matrix
....................................................................................................................................................................................................................................
Table 1-3 Module type (continued)
....................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC 1-9
24-3005 UA08.1
Issue 3.01 October 2012
Introduction to 9370 RNC 9370 RNC compatibility matrix
....................................................................................................................................................................................................................................
9370 RNC application package
The following table lists the application packages to be downloaded and applied to the
RNC:
....................................................................................................................................................................................................................................
1-10 Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
2 Material requirements
2
Overview
Purpose
This chapter describes the material requirements for commissioning the Alcatel-Lucent
9370 RNC.
Contents
...................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC 2-1
24-3005 UA08.1
Issue 3.01 October 2012
Material requirements Prerequisites for RNC commissioning
....................................................................................................................................................................................................................................
Software
The softwares required for commissioning the 9370 RNC are as follows
Windows XP, Windows Vista, or Windows Seven
Hyper Terminal
Server U version 2.2 or later or other ftp server software.
DVD-ROMs containing the 9370 RNC software release
No other materials are required to perform this method.
....................................................................................................................................................................................................................................
2-2 Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
3 3recautions and
P
preparations
Overview
Purpose
This chapter describes the precautions and the preparations necessary to commission the
9370 RNC.
Contents
Precautions 3-2
Preparations 3-3
Check list 3-4
...................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC 3-1
24-3005 UA08.1
Issue 3.01 October 2012
Precautions and preparations Precautions
....................................................................................................................................................................................................................................
Precautions
Safety measures
Observe the general safety precautions against personal injury and equipment damage
outlined in the regional Installation Safety Manual at all times.
Observe the product specific safety precautions outlined in IM 45-9399 Alcatel-Lucent
9370 RNC Product Safety Installation Requirement.
Use of the antistatic wrist strap when handling modules.
....................................................................................................................................................................................................................................
3-2 Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
Precautions and preparations Preparations
....................................................................................................................................................................................................................................
Preparations
Preparations for RNC commissioning
It is strongly recommended that this method be read in its entirety before starting the
operations presented herein.
Prior to starting the operations presented in this method, arrange all materials, tools, and
test equipment at the work location so as to minimize fatigue and inconvenience.
....................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC 3-3
24-3005 UA08.1
Issue 3.01 October 2012
Precautions and preparations Check list
....................................................................................................................................................................................................................................
Check list
RNC commissioning pre-checks
Verify the following items have been received and/or accomplished before proceeding
with the RNC commissioning procedure:
The power supply cables are installed (-48Vdc voltage and grounding).
The internal cables are installed (power supply cables in the SIM modules, optical
fibers between 9370 RNC and the POC if present.
Check that the delivered equipment configuration complies with the requirement and
the applicable technical status in 9370 RNC UTRAN UA08.1.
....................................................................................................................................................................................................................................
3-4 Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
4 4370 RNC Commissioning
9
procedure
Overview
Purpose
This chapter describes the procedures to be performed for commissioning the 9370 RNC
The procedures available in this chapter are applicable for UA08.1 release, with the
following minimum RNC configuration:
DCPS or eDCPS cards are inserted in slots 2, 3, 4, and 5 of the 9370 RNC, and in no
other slots.
R18 RNC software base is used.
Contents
...................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC 4-1
24-3005 UA08.1
Issue 3.01 October 2012
9370 RNC Commissioning procedure Procedure Overview
....................................................................................................................................................................................................................................
Procedure Overview
Purpose
This topic provides an overview of the procedural steps for 9370 RNC commissioning.
Step Procedure
Procedures to be executed on site: local
1 9370 RNC cabinet power on (p. 4-4)
2 Hyper-terminal configuration (p. 4-7)
3 Hardware configuration using startup: out-band OAM (p. 4-10)
Procedures to be executed on site or on remote
4 Creation of SDS server (p. 4-19)
5 RNC software download (p. 4-25)
6 RNC parameters configuration (p. 4-29)
7 Set time in the 9370 RNC (p. 4-40)
8 Final checks (p. 4-45)
Step Procedure
Procedures to be executed on site: local
1 9370 RNC cabinet power on (p. 4-4)
2 Hyper-terminal configuration (p. 4-7)
3 Hardware configuration using startup: in-band OAM (p. 4-32)
Procedures to be executed on site or on remote
4 Creation of SDS server (p. 4-19)
5 RNC software download (p. 4-25)
....................................................................................................................................................................................................................................
4-2 Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
9370 RNC Commissioning procedure Procedure Overview
....................................................................................................................................................................................................................................
Table 4-2 In-Band 4pGe OAM Configuration procedural steps (continued)
....................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC 4-3
24-3005 UA08.1
Issue 3.01 October 2012
9370 RNC Commissioning procedure 9370 RNC cabinet power on
....................................................................................................................................................................................................................................
Procedure
The steps for switching on the 9370 RNC cabinet are as follows:
...................................................................................................................................................................................................
1 Ensure that all power breakers on each BIM are switched off.
Note: Risk of equipment damage by reverse polarity
Use the plus (+) and minus (-) symbols on the rear of the (BIP) to ensure that the
polarity of each A and B battery (-57/-43 V dc) and battery return for the input power
feeds is correct, the minus (-) is -48V and plus (+) is -48V return
When powering up the BIP, reversed polarity will damage circuits inside it the BIP
would have to be replaced.
...................................................................................................................................................................................................
2 Verify on the rear of the cabinet that the voltage between the A1- and A1+ pair is negative
and ranges within:
Nominal power 48 Vdc: min. 40 Vdc max 57.6 Vdc refer to Figure 4-1, Verification
of the Range of VDC (p. 4-5)
Nominal Power 60 Vdc: min. 50 Vdc max 72 Vdc refer to Figure 4-1, Verification of
the Range of VDC (p. 4-5)
Note: The minus (-) is -48V and plus (+) is -48V return for nominal power 48 Vdc.
...................................................................................................................................................................................................
3 Verify on the rear of the cabinet that the voltage between the B1- and B1+ pair is negative
and ranges within:
Nominal power 48 Vdc: min. 40 Vdc max 57.6 Vdc refer to Figure 4-1, Verification
of the Range of VDC (p. 4-5)
Nominal Power 60 Vdc: min. 50 Vdc max 72 Vdc refer to Figure 4-1, Verification of
the Range of VDC (p. 4-5)
Note: The minus (-) is -48V and plus (+) is -48V return for nominal power 48 Vdc.
....................................................................................................................................................................................................................................
4-4 Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
9370 RNC Commissioning procedure 9370 RNC cabinet power on
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
4 Ensure that all FPs boards & CP spare board are unseated (rear connectors are not
touching the backplane), the CP in slot 0 must remain seated.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC 4-5
24-3005 UA08.1
Issue 3.01 October 2012
9370 RNC Commissioning procedure 9370 RNC cabinet power on
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
6 Check that the following LEDs are illuminate, refer to Figure 4-3, Alarm LED Status
Indicators for BIM Modules (p. 4-6)
Note: For more details of the 9370 RNC LEDs cards, refer to Appendix A,
Download and activate fabric software.
E...................................................................................................................................................................................................
N D O F S T E P S
....................................................................................................................................................................................................................................
4-6 Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
9370 RNC Commissioning procedure Hyper-terminal configuration
....................................................................................................................................................................................................................................
Hyper-terminal configuration
Purpose
This procedure configures the Hyper-Terminal.
Procedure
The steps for configuring the Hyper-terminal are as follows:
...................................................................................................................................................................................................
1 Connect your PC to the CP card of the 9370 RNC with serial cable (DB9/DB9).
The following figure shows the laptop connection with the CP card of the 9370 RNC:
....................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC 4-7
24-3005 UA08.1
Issue 3.01 October 2012
9370 RNC Commissioning procedure Hyper-terminal configuration
....................................................................................................................................................................................................................................
The steps for configuring the Hyper- terminal connection are as follows:
1. Click on Start/Program/Accessories/Communications/Hyper terminal
2. Double click on the icon "Hypertrm.exe" to launch Hyper Terminal application.
3. Enter a name for the connection (for instance "CP") and click on OK
4. Select the right Serial port (normally COM1) and click on OK.
....................................................................................................................................................................................................................................
4-8 Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
9370 RNC Commissioning procedure Hyper-terminal configuration
....................................................................................................................................................................................................................................
6. Once connected and after all boot messages, press enter the following prompt should
appear. If not, check the cable and the Hyper Terminal parameters.
E...................................................................................................................................................................................................
N D O F S T E P S
....................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC 4-9
24-3005 UA08.1
Issue 3.01 October 2012
9370 RNC Commissioning procedure Hardware configuration using startup: out-band OAM
....................................................................................................................................................................................................................................
Procedure
The steps for configuring the 9370 RNC hardware using startup Enhancements tool
(out-band OAM) are as follows:
...................................................................................................................................................................................................
1 Ensure that all cards (16pOC3/STM1, DCPS/eDCPS, 4pGE) are inserted except the spare
CP in slot 1.
Note:
There is a Startup tool on all CP that allows doing IP configuration for its Ethernet
port.
If the eDCPS cards are available in full RNC shelf, it may take more than 5
minutes for all FPs to come online.
To check the Startup tool load in the CP card, execute the following actions:
Login to the system (no factory login): example: debug
<Enter> debug (login)
<Enter> debug (password)
...................................................................................................................................................................................................
<Enter> startup
You have invoked the 'StartUp' facility. This facility is
for use during system installation and commissioning only.
Use at any other time may result in a loss of provisioning
information.
Please enter 'quit' or select the desired method of NMS
connectivity:
1. A connection to NMS through a DPN network.
2. A connection to NMS through a Passport network.
3. A direct connection to NMS from this Passport using
Frame Relay PVC.
4. A connection to NMS via Passport IP networking.
<Enter> 4
Note: If the CP3/4 is already commissioned you can have the following screen
displayed:
....................................................................................................................................................................................................................................
4-10 Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
9370 RNC Commissioning procedure Hardware configuration using startup: out-band OAM
....................................................................................................................................................................................................................................
<Enter> 5
....................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC 4-11
24-3005 UA08.1
Issue 3.01 October 2012
9370 RNC Commissioning procedure Hardware configuration using startup: out-band OAM
....................................................................................................................................................................................................................................
<Enter> 1
You have invoked the 'StartUp' facility. This facility is for use
during system installation and commissioning only.
Use at any other time may result in a loss of provisioning
information.
You have not confirmed your current provisioning view.
Shall I issue the 'confirm prov' command for you? [yes]
Confirmation succeeded
The available releases of BASE software are:RI8xxxx.
After this step the LEDs of all inserted cards becomes green for CP
board & solid amber for PS boards.
The currently selected NMS connectivity is:
A connection to NMS via Passport IP networking.
The currently selected media type is:
OamEnet.
....................................................................................................................................................................................................................................
4-12 Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
9370 RNC Commissioning procedure Hardware configuration using startup: out-band OAM
....................................................................................................................................................................................................................................
The MDM and Nortel Networks Multiservice Switch are on different IP
subnets.
Do you wish to change the selected MDM connectivity? [no]: No
Please enter 'quit' or select one of the following:
1. Reset node to CP-only software.
2. Create Sw lpts and load software on FPs.
3. Perform on-card tests of each card in the node.
4. Configure the node for MDM connectivity.
5. Display the cards inserted in the node.
6. Provision a spare CP.
7. Create RNC software lpts, Interfaces, Internal exchanges.
8. Configure RNC parameters.
9. Configure InBand OAM connectivity to another node via RNC
10. Change selected MDM connectivity.
11. Download RNC software.
12. Confirm the provisioning.
<Enter> 2
4 Run Startup Option 4 & enter the 9370 RNC Network parameters
Note: Ensure that the Ethernet cable is connected to CP0 port 0 before running startup
Option 4, else the procedure fails to execute.
....................................................................................................................................................................................................................................
for use during system installation and commissioning only.
Use at any other time may result in a loss of provisioning
information.
The currently selected NMS connectivity is:
A connection to NMS via Passport IP networking.
The currently selected media type is:
OamEnet
NMS and Passport are on the same IP subnet.
Do you wish to change the selected NMS connectivity? [no]
Please enter 'quit' or select one of the following:
1. Reset node to CP-only software.
2. Create Sw lpts and load software on FPs.
3. Perform on-card tests of each card in the node.
4. Configure the node for MDM connectivity.
5. Display the cards inserted in the node.
6. Provision a spare CP.
7. Create RNC software lpts, Interfaces, Internal exchanges.
8. Configure RNC parameters.
9. Configure InBand OAM connectivity to another node via RNC.
10. Change selected MDM connectivity.
11. Download RNC software.
12. Confirm the provisioning.
<Enter> 4
IP Connection configuration
Enter the Startup configuration information as prompted or enter
'quit
Virtual router name [0]
IP port address (aa.bb.cc.dd) [] 10.124.183.65
IP port Network Mask (aa.bb.cc.dd) [] 255.255.255.240
IP broadcast address (aa.bb.cc.dd) [] 10.124.183.79
Next hop IP address (aa.bb.cc.dd) [] 10.124.183.78
Note: Next hop IP address is displayed only if NMS and passport are not in the same
subnet, see step 2 procedure 3.
Note: The system display all inserted cards (see example on next step 5).
5 Run Startup Option 5. The output shows the DCPS or eDCPS cards inserted in slots 2 ,3,
4, and 5 of 9370 RNC.
The output screen displayed at this stage must be the same as shown below:
....................................................................................................................................................................................................................................
4-14 Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
9370 RNC Commissioning procedure Hardware configuration using startup: out-band OAM
....................................................................................................................................................................................................................................
1. Reset node to CP-only software.
2. Create Sw lpts and load software on FPs.
3. Perform on-card tests of each card in the node.
4. Configure the node for MDM connectivity.
5. Display the cards inserted in the node.
6. Provision a spare CP.
7. Create RNC software lpts, Interfaces, Internal exchanges.
8. Configure RNC parameters.
9. Configure InBand OAM connectivity to another node via RNC.
10. Change selected MDM connectivity.
11. Download RNC software.
12. Confirm the provisioning.
<Enter> 5
+---+---+---+---+---+---+---+---+
| | | | | | | | |
| C | | P | P | P | P | | |
| P | | k | k | k | k | | |
| e | | t | t | t | t | | |
| E | | S | S | S | S | | |
| | | e | e | e | e | | |
| | | r | r | r | r | | |
| | | v | v | v | v | | |
| | | S | S | S | S | | |
| | | P | P | P | P | | |
| | | x | x | x | x | | |
| | | | | | | | |
+---+---+---+---+---+---+---+---+
00 01 02 03 04 05 06 07
+---+---+---+---+---+---+---+---+
| | | | | | | | |
| 1 | | | | | | 4 | |
| 6 | | | | | | p | |
| p | | | | | | G | |
| O | | | | | | e | |
| C | | | | | | | |
| 3 | | | | | | | |
| S | | | | | | | |
| m | | | | | | | |
| I | | | | | | | |
| r | | | | | | | |
| A | | | | | | | |
+---+---+---+---+---+---+---+---+
08 09 10 11 12 13 14 15
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC 4-15
24-3005 UA08.1
Issue 3.01 October 2012
9370 RNC Commissioning procedure Hardware configuration using startup: out-band OAM
....................................................................................................................................................................................................................................
Note: The current provisioning is already confirmed. This is an acceptable response.
<Enter> 6
Note: The 9370 RNC ask to insert the CP spare, Plug in it and wait until the LED of
the spare card is blinking green and the synchronization is completed.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
9 Quit startup
<Enter> quit
....................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC 4-17
24-3005 UA08.1
Issue 3.01 October 2012
9370 RNC Commissioning procedure Hardware configuration using startup: out-band OAM
....................................................................................................................................................................................................................................
Shall I issue the 'commit prov' command for you? [yes]
start -force prov ... ok
check prov ... ok
save -f(startup) prov ... ok
commit prov ... ok
end prov ... ok
Commit succeeded
Startup can save and commit a configuration employing the following naming structure
startup.full.xxx. Committing the startup configuration saves the configuration even if the
Node reboots or if the next step fails.
...................................................................................................................................................................................................
> start pr
Vr/0 Ip RipIf
A total of 1 components have been deleted.
ok 2011-08-29 16:45:47.99
In the RNC Telnet window
PROV> ch pr
PROV> act pr
PROV> conf pr
PROV> save pr
PROV> commit pr
PROV> end pr
...................................................................................................................................................................................................
11 Execute the ping commands to the verify the IP connectivity of the RNC to the next HOP
router and WMS. See the examples given:
Ping to the next HOP IP address
ping -ip(10.171.25.129) -trace vr/0 ip icmp
Ping to the WMS
ping -ip(10.40.7.229) -trace vr/0 ip icmp
E...................................................................................................................................................................................................
N D O F S T E P S
....................................................................................................................................................................................................................................
4-18 Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
9370 RNC Commissioning procedure Creation of SDS server
....................................................................................................................................................................................................................................
Procedure
The steps for creating the SDS server are as follows:
...................................................................................................................................................................................................
1 Local Commissioning
Connect the laptop PC to the CP card via Ethernet Crossed cable (Use Port N 0 of the CP
card)
Change the IP @ (same sub-mask as CP @ IP) of the laptop Ethernet card if
necessary.
On laptop Start/Setting/Control Panel.
Double click on Network icon, see the next graphic:
....................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC 4-19
24-3005 UA08.1
Issue 3.01 October 2012
9370 RNC Commissioning procedure Creation of SDS server
....................................................................................................................................................................................................................................
Select the protocol TCP/IP of the Ethernet card and then click on "properties" the
following window appears see the next graphic:
....................................................................................................................................................................................................................................
4-20 Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
9370 RNC Commissioning procedure Creation of SDS server
....................................................................................................................................................................................................................................
Check that the CP is replaying if not repeat from step 1 of this procedure for Local
Commissioning.
Check the network parameters for Remote Commissioning
....................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC 4-21
24-3005 UA08.1
Issue 3.01 October 2012
9370 RNC Commissioning procedure Creation of SDS server
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
On the Serv-U window, select Setup/FTP-Server and check that the option Enable
security is selected
On the Serv-U window, under the Setup/FTP-Server pull down menu in the tool bar,
select "Setup/Users".
In Setup Users window, enter new "User Name".
Enter new "Password"
Enter in Home directory delivery/PASSPORT (DVD-ROM directory which contains
the sub-directory "software")
....................................................................................................................................................................................................................................
4-22 Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
9370 RNC Commissioning procedure Creation of SDS server
....................................................................................................................................................................................................................................
On the Setup Users window, select add icon and Enter Path name delivery/PASSPORT
(DVD-ROM directory which contains sub-directory "software")
Confirm by OK.
On the Setup Users window, confirm all by store and after OK.
On the Serv-U window, under the Setup/FTP-Server pull down menu in the tool bar,
select "Setup/IP-Access".
Select "Allow access" confirm by OK.
Minimize Serv-U
....................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC 4-23
24-3005 UA08.1
Issue 3.01 October 2012
9370 RNC Commissioning procedure Creation of SDS server
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
4-24 Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
9370 RNC Commissioning procedure RNC software download
....................................................................................................................................................................................................................................
Procedure
The steps for downloading the RNC software are as follows:
...................................................................................................................................................................................................
<Enter> 11
....................................................................................................................................................................................................................................
ethernet_RI81036
Please enter the desired Patch release name [RI8xxxxxxxxxxx]
Note: Fill the patch release name then press Enter, the following patch release will be
displayed (RI810360B3251 is given as an example).
Do you want to download secure software packages(ipsec,
secureShell and RNCCiph)? [no] (enter Yes if OAM security feature is selected)
....................................................................................................................................................................................................................................
4-26 Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
9370 RNC Commissioning procedure RNC software download
....................................................................................................................................................................................................................................
where 1 is the number of the spare slot
Check that the spare card is locked
In the RNC Telnet window
> d sh ca/1 adminState
where 1 is the number of the spare slot
This remote commissioning step is terminate, go back to the startup and continue with
the procedure.
<Enter> 7
....................................................................................................................................................................................................................................
atmNetworking_RI81036 genericUtilities_RI81036
iRNC_RI81036 networking_RI81036
ss7Apc_RI81036 wanDte_RI81036
wirelessCommon_RI81036 apcBase_RI81036
baseExt_RI81036 iRNCApc_RI81036
baseExt_RI81036 iRNCApc_RI81036
ss7Apc_RI81036 cnp_RI81036
cRNCApc_RI81036 ethernet_RI81036
Are these values correct? This will activate provisioning [no] yes
start -force prov ... ok
copy prov ... ok
Screen Response............... (cut off)
E...................................................................................................................................................................................................
N D O F S T E P S
....................................................................................................................................................................................................................................
4-28 Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
9370 RNC Commissioning procedure RNC parameters configuration
....................................................................................................................................................................................................................................
Procedure
The steps for configuring the RNC parameters are as follows:
...................................................................................................................................................................................................
<Enter> 8
2 Quit startup.
....................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC 4-29
24-3005 UA08.1
Issue 3.01 October 2012
9370 RNC Commissioning procedure RNC parameters configuration
....................................................................................................................................................................................................................................
6. Provision a spare CP.
7. Create RNC software lpts, Interfaces, Internal exchanges.
8. Configure RNC parameters.
9. Configure InBand OAM connectivity to another node via RNC.
10. Change selected MDM connectivity.
11. Download RNC software.
12. Confirm the provisioning.
<Enter> quit
...................................................................................................................................................................................................
> start pr
PROV> ch pr
PROV> act pr
PROV> conf pr
PROV> save pr
PROV> commit pr
PROV> end pr
...................................................................................................................................................................................................
4 Insert or unlock the spare CP. This step triggers the cards to be configured.
Local Commissioning,
Re-seat/re-insert the spare card. Wait for the file system to synchronize (LED will be
blinking green)
Remote Commissioning,
Unlock the spare card
In the RNC Telnet window
> unlock sh ca/1
where 1 is the number of the spare slot.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
4-30 Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
9370 RNC Commissioning procedure RNC parameters configuration
....................................................................................................................................................................................................................................
In the RNC Telnet window
> Sync fs
When the syncProgress is 100% and syncStatus is Synchronized, this step is completed.
...................................................................................................................................................................................................
> d -p ac userid/*
> start pr
PROV> add ac userid/debug
PROV> set ac userid/debug password debug, commandscope network
PROV> set ac userid/debug allowedaccess local telnet fmip ftp
PROV> set ac userid/debug commandImpact debug
PROV> ch prov
PROV> act prov
PROV> confirm prov
PROV> add ac userid/mdmadmin
PROV> set ac userid/mdmadmin password mdmadmin, commandscope
network
PROV> set ac userid/mdmadmin allowedaccess local telnet fmip ftp
PROV> set ac userid/mdmadmin commandImpact debug
PROV> ch prov
PROV> act prov
PROV> confirm prov
PROV> save -f(new_view_name) pr
PROV> commit pr
PROV> end pr
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC 4-31
24-3005 UA08.1
Issue 3.01 October 2012
9370 RNC Commissioning procedure Hardware configuration using startup: in-band OAM
....................................................................................................................................................................................................................................
Procedure
The steps for configuring the 9370 RNC hardware using startup (in-band OAM) are as
follows:
...................................................................................................................................................................................................
1 Ensure that all cards (16pOC3/STM1, DCPS/eDCPS, 4pGE) are inserted except the spare
CP in slot 1.
Note: If the eDCPS cards are available in full shelf, it may take more than 5 mins for
all FPs to come up.
Open a telnet session on the active CP card
In the RNC Telnet window:
Launch startup tool
<Enter> debug (login)
<Enter> debug (password)
<Enter> startup
....................................................................................................................................................................................................................................
OamEnet
The MDM and Nortel Networks Multiservice Switch are on different IP
Do you wish to change the selected MDM connectivity? [no]: YES
A change in MDM connnectivity will reset the provisioning
information.
Continue? [no]: YES
Then you will return to the startup menu displayed above select
option 4.
<Enter> 4
<Enter> 1
....................................................................................................................................................................................................................................
If you continue, please confirm the following is satisfactory:
- A minimal provisioning file will be created and activated.
- The CP will activate using release base_RI81036.
- The node will reboot with this new provisioning file.
Are you sure you want to continue? [no] y
Please enter the following information required
for CP only software:
Cluster node? [no] n
Is this value correct? [yes] y
Node Id [32]
Node Name [RNC232_I]
Region Id [0]
NAMS Id [288]
Are these values correct? This will activate the provisioning.
[yes] y
start -force prov ... ok
..................................(Screen response Cut off)
...................................................................................................................................................................................................
You have invoked the 'StartUp' facility. This facility is for use
during system installation and commissioning only.
Use at any other time may result in a loss of provisioning
information.
he currently selected MDM connectivity is:
A connection to MDM via IP networking.
The currently selected media type is:
4pGe
The MDM and Nortel Networks Multiservice Switch are on different IP
subnets.
Do you wish to change the selected MDM connectivity? [no] n
Please enter 'quit' or select one of the following:
1. Reset node to CP-only software.
2. Create Sw lpts and load software on FPs.
3. Perform on-card tests of each card in the node.
4. Configure the node for MDM connectivity.
5. Display the cards inserted in the node.
6. Provision a spare CP.
7. Create RNC software lpts, Interfaces, Internal exchanges.
8. Configure RNC parameters.
9. Configure InBand OAM connectivity to another node via RNC.
10. Change selected MDM connectivity.
....................................................................................................................................................................................................................................
4-34 Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
9370 RNC Commissioning procedure Hardware configuration using startup: in-band OAM
....................................................................................................................................................................................................................................
11. Download RNC software.
12. Confirm the provisioning.
<Enter> 2
3 Run Startup Option 4 & enter the 9370 RNC Network parameters
You have invoked the 'StartUp' facility. This facility is for use
during system installation and commissioning only.
Use at any other time may result in a loss of provisioning
information.
he currently selected MDM connectivity is:
A connection to MDM via IP networking.
The currently selected media type is:
4pGe
The MDM and Nortel Networks Multiservice Switch are on different IP
subnets.
Do you wish to change the selected MDM connectivity? [no] n
Please enter 'quit' or select one of the following:
1. Reset node to CP-only software.
2. Create Sw lpts and load software on FPs.
3. Perform on-card tests of each card in the node.
4. Configure the node for MDM connectivity
5. Display the cards inserted in the node.
6. Provision a spare CP.
....................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC 4-35
24-3005 UA08.1
Issue 3.01 October 2012
9370 RNC Commissioning procedure Hardware configuration using startup: in-band OAM
....................................................................................................................................................................................................................................
7. Create RNC software lpts, Interfaces, Internal exchanges.
8. Configure RNC parameters.
9. Configure InBand OAM connectivity to another node via RNC.
10. Change selected MDM connectivity.
11. Download RNC software.
12. Confirm the provisioning.
<Enter> 4
<Enter> 2
<Enter> 2
....................................................................................................................................................................................................................................
4-36 Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
9370 RNC Commissioning procedure Hardware configuration using startup: in-band OAM
....................................................................................................................................................................................................................................
Node Topology: A connection to MDM via IP networking.
Media Type: 4pGe
IP port address: 10.99.0.2
IP port network mask: 255.255.255.252
IP broadcast address: 10.99.0.4
Next hop IP address: 10.99.0.1
Slot Number: 14
Card Type: 4pGe
Port Number: 0
Port Mode Type: VLAN
GE optical Module: LX
Are these values correct? This will activate the provisioning [yes] Y
start -force prov ... ok
add lp/14 ethernet/0 ... ok
set lp/14 ethernet/0 opticalModule type LX ... ok
add lan/0... ok
set lp/14 eth/0 applicationFramerName Lan/0 Framer ... ok
add VM/0 ... ok
add VM/0 if/0 ... ok
set VM/0 if/0 mode alwaysUpInterface ... ok
add vr/0 ... ok
set vr/0 virtualRouterProcess lp/0 ... ok
add vr/0 ip ... ok
add -s vr/0 ip Static routeEntry/0.0.0.0,0.0.0.0,0 nextHop/
10.99.0.1 ... ok
add vr/0 pp/GIGE1 ip logical/10.99.0.2 ... ok
add -s vr/0 pp/OAMINBAND1 ip logical/10.99.0.249 ... ok
add vr/0 pp/GIGE1 ip logical/10.99.0.2 net 255.255.255.252 ... ok
add vr/0 pp/OAMINBAND1 ip logical/10.99.0.249 net 255.255.255.240
... ok
set vr/0 pp/GIGE1 linkToMedia lan/0 ... ok
set vr/0 pp/OAMINBAND1 linkToMedia vm/0 if/0 ... ok
add lan/0 vlan/450 ... ok
set lp/14 ethernet/0 maxFramesize 1522 ... ok
set vr/0 pp/GIGE1 link lan/0 vlan/450 ... ok
check prov ... ok
activate -force prov ... ok
confirm prov ... ok
StartUp configuration completed
Please enter 'quit' or select one of the following
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC 4-37
24-3005 UA08.1
Issue 3.01 October 2012
9370 RNC Commissioning procedure Hardware configuration using startup: in-band OAM
....................................................................................................................................................................................................................................
4. Configure the node for MDM connectivity.
5. Display the cards inserted in the node.
6. Provision a spare CP.
7. Create RNC software lpts, Interfaces, Internal exchanges.
8. Configure RNC parameters.
9. Configure InBand OAM connectivity to another node via RNC.
10. Change selected MDM connectivity.
11. Download RNC software.
12. Confirm the provisioning.
<Enter> 12
<Enter> 6
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
5. Display the cards inserted in the node.
6. Provision a spare CP.
7. Create RNC software lpts, Interfaces, Internal exchanges.
8. Configure RNC parameters.
9. Configure InBand OAM connectivity to another node via RNC.
10. Change selected MDM connectivity.
11. Download RNC software.
12. Confirm the provisioning.
<Enter> 12
...................................................................................................................................................................................................
7 Quit startup
<Enter> quit
8 To complete the RNC commissioning, startup step 7 and 8 must be completed. For more
information, see Step 2 of RNC software download for startup step 7, and Step 1 of
RNC parameters configuration for startup step 8.
E...................................................................................................................................................................................................
N D O F S T E P S
....................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC 4-39
24-3005 UA08.1
Issue 3.01 October 2012
9370 RNC Commissioning procedure Set time in the 9370 RNC
....................................................................................................................................................................................................................................
Procedure
The steps for setting time in 9370 RNC are as follows:
...................................................................................................................................................................................................
1 Note: There are two options to configure the time zone on the network: all NE and
OAM are set to GMT time or all NE and OAM are set to the unique local time (even
if NE are in different time zone).
Check the time network choice: all NE to GMT or all NE to a unique local time
Set the date with the right time zone
To configure a local time zone on the RNC, first the RNC must be set to GMT with an
offset of 0 and then the operator modifies the offset to reflect the local time zone
....................................................................................................................................................................................................................................
4-40 Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
9370 RNC Commissioning procedure Set time in the 9370 RNC
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
> d time
==|==============================================================
| SI_IN3 Time
==|===========================(A)================================
1|moduleTime 2011-08-10 10:25:13.59
2|
offset 0 minutes
3|syncStatus synchronized
4|mainServer 135.120.165.17
5|syncSources 135.120.165.17
6|xntpVersion 3
7|leapSecondsApplied 31
8|dbgUtcOffset 0 microsec
9|dbgStream ~nts0 ~nts1 ~nts2 ~nts3 ~nts4 ~nts5
~nts6 ~nts7
| ~nts8 ~nts9 ~tms0 ~tms1 ~tms2 ~tms3
~tms4 ~tms5
| ~tms6 ~tms7 ~tms8 ~tms9 ~tms10 ~tms11
~tms12
| ~tms13 ~tms14 ~tms15 ~tms16 ~tms17
~tms18 ~tms19
| ~ntsAll ~tmsAll
10|dbgMode loose
11|dbgPreLeapSecondConditions timeComponent
Note: When the "offset" attribute is set to "0", the module time displayed is in GMT
mode, if it is the case apply the following step.
Adjust the RNC time to GMT time
In the RNC Telnet window
> Set time moduletime YYYY-MM-DD HH:MM:SS.CC
Output example
In the RNC Telnet window
> Set time moduletime 2011-08-10 10:25:13.59
Adjust the "offset" attribute corresponding to time zone.
To change the Time Zone, execute the following command: example: chtz NFT-1DFT
In the RNC Telnet window
> set time offset x
Output example for x=60
....................................................................................................................................................................................................................................
4-42 Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
9370 RNC Commissioning procedure Set time in the 9370 RNC
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
> st pr
....................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC 4-43
24-3005 UA08.1
Issue 3.01 October 2012
9370 RNC Commissioning procedure Set time in the 9370 RNC
....................................................................................................................................................................................................................................
PROV> ch pr
PROV> act pr
PROV> conf pr
PROV> save pr
PROV> commit pr
PROV> end pr
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
4-44 Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
9370 RNC Commissioning procedure Final checks
....................................................................................................................................................................................................................................
Final checks
Purpose
This procedure finalizes the commissioning of the 9370 RNC and can be executed locally
or remotely.
Procedure
The final checks to be performed on 9370 RNC are as follows:
...................................................................................................................................................................................................
1 Only for local commissioning: Check the LED alarm status for every card. The LEDs on
each module should be: solid green for active cards (active CP card) and fast flashing
green for cards running as standby (spare CP card)
...................................................................................................................................................................................................
> st pr
> set Vr/0 Pp/OAMENET0 IpPort proxyArpStatus enabled
Example:
....................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC 4-45
24-3005 UA08.1
Issue 3.01 October 2012
9370 RNC Commissioning procedure Final checks
....................................................................................................................................................................................................................................
Example:
....................................................................................................................................................................................................................................
4-46 Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
9370 RNC Commissioning procedure Final checks
....................................................................................................................................................................................................................................
| 3| 4|pc | 1|na | 0| 0| 0| 240
| 3| 5|rab | 5|na | 56| 0| 0| 0
| 4| 0|rab | 6|na | 69| 0| 0| 0
| 4| 1|tmu | 2|na | na| na| na| na
| 4| 2|aNi | 0|spared| na| na| na| na
| 4| 3|rab | 7|na | 69| 0| 0| 0
| 4| 4|pc | 2|na | 0| 0| 0| 246
| 4| 5|aOmu | 0|spared| na| na| na| na
| 5| 0|rab | 8|na | 69| 0| 0| 0
| 5| 1|tmu | 3|na | na| na| na| na
| 5| 2|sNi | 1|spared| na| na| na| na
| 5| 3|rab | 9|na | 69| 0| 0| 0
| 5| 4|pc | 3|na | 0| 0| 0| 240
| 5| 5|sOmu | 1|spared| na| na| na| na
| 6| 0|rab | 10|na | 69| 0| 0| 0
| 6| 1|tmu | 4|na | na| na| na| na
| 6| 2|rab | 11|na | 56| 0| 0| 0
| 6| 3|rab | 12|na | 70| 0| 0| 0
| 6| 4|pc | 4|na | 0| 0| 0| 250
| 6| 5|rab | 13|na | 28| 0| 0| 0
| 7| 0|rab | 14|na | 69| 0| 0| 0
| 7| 1|tmu | 5|na | na| na| na| na
| 7| 2|rab | 15|na | 69| 0| 0| 0
| 7| 3|rab | 16|na | 56| 0| 0| 0
| 7| 4|pc | 5|na | 0| 0| 0| 240
| 7| 5|rab | 17|na | 28| 0| 0| 0
|10| 0|rab | 18|na | 69| 0| 0| 0
|10| 1|tmu | 6|na | na| na| na| na
|10| 2|rab | 19|na | 70| 0| 0| 0
|10| 3|rab | 20|na | 56| 0| 0| 0
|10| 4|pc | 6|na | 0| 0| 0| 240
|10| 5|rab | 21|na | 28| 0| 0| 0
|11| 0|rab | 22|na | 70| 0| 0| 0
|11| 1|tmu | 7|na | na| na| na| na
|11| 2|rab | 23|na | 70| 0| 0| 0
|11| 3|rab | 24|na | 56| 0| 0| 0
|11| 4|pc | 7|na | 0| 0| 0| 240
|11| 5|rab | 25|na | 28| 0| 0| 0
|12| 0|rab | 26|na | 69| 0| 0| 0
|12| 1|tmu | 8|na | na| na| na| na
|12| 2|rab | 27|na | 56| 0| 0| 0
|12| 3|rab | 28|na | 70| 0| 0| 0
|12| 4|pc | 8|na | 0| 0| 0| 240
|12| 5|tmu | 9|na | na| na| na| na
|13| 0|rab | 29|na | 70| 0| 0| 0
|13| 1|tmu | 10|na | na| na| na| na
|13| 2|rab | 30|na | 70| 0| 0| 0
|13| 3|rab | 31|na | 56| 0| 0| 0
|13| 4|pc | 9|na | 0| 0| 0| 250
|13| 5|tmu | 11|na | na| na| na| na
ok 2011-11-03 11:49:49.96
> d rncin tmu/* sg
Output example
....................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC 4-47
24-3005 UA08.1
Issue 3.01 October 2012
9370 RNC Commissioning procedure Final checks
....................................................................................................................................................................................................................................
RncIn Tmu/*
+===+--------+----------------------------------------
|Tmu| sg |Response
+===+--------+----------------------------------------
| 0| 9|
| 1| 3|
| 2| 7|
| 3| na|
| 4| na|
| 5| 4|
| 6| 0|
| 7| 6|
| 8| 1|
| 9| 8|
| 10| 2|
| 11| 5|
ok 2011-11-03 11:50:42.49
> d lp/* ap/1 rnc
Output example
....................................................................................................................................................................................................................................
| 7|rab | 17|na | 28| 0| 0| 0
|10|rab | 21|na | 28| 0| 0| 0
|11|rab | 25|na | 28| 0| 0| 0
|12|tmu | 9|na | na| na| na| na
|13|tmu | 11|na | na| na| na| na
ok 2011-11-03 11:51:25.10
...................................................................................................................................................................................................
5 Finish filling out the report sheet. All non-compliance case has to be physically.Spotted
on site and recapitulated on Appendix E, Report sheet.
...................................................................................................................................................................................................
6 Leave one copy of the report sheet on site, and send one to the co-ordinator.
...................................................................................................................................................................................................
9 The next step is the integration of the RNC in the network, refer to the IM: 3-65-6222.
E...................................................................................................................................................................................................
N D O F S T E P S
....................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC 4-49
24-3005 UA08.1
Issue 3.01 October 2012
9370 RNC Commissioning procedure Final checks
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
4-50 Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
Appendix A: Download and
activate fabric software
Overview
Purpose
This appendix provides the procedure to download and activate fabric software.
Contents
...................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC A-1
24-3005 UA08.1
Issue 3.01 October 2012
Download and activate fabric software Download and activate fabric software
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
If the response is a load number, you need to upgrade the firmware.
...................................................................................................................................................................................................
6 Verify that the fabric card operates correctly with the new firmware:
In the 9370 RNC Telnet window
> start shelf fabricCard/<fabcard_inst> test
Note: The test results show if the fabric card is operating correctly.
...................................................................................................................................................................................................
7 If there are problems with the upgraded fabric card, it might be necessary to make the
fixed bank the bankOnShelfRestart using the following command:
In the 9370 RNC Telnet window
> set shelf fabricCard/<fabcard_inst> bankOnShelfRestart
Note: If the writable bank is set as the committed bank and it becomes corrupted, the
fabric card might not come up. If the writable bank is corrupted, it must be replaced.
Contact your ALU representative.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC A-3
24-3005 UA08.1
Issue 3.01 October 2012
Download and activate fabric software Download and activate fabric software
....................................................................................................................................................................................................................................
> unlock shelf fabricCard/<fabcard_inst>
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
A-4 Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
Appendix B: DB-9 to RJ45
adapter
Overview
Purpose
This Appendix describes the pin out configuration needed for the DB-9 to RJ45 adapter
when the RNC 9370 is connecting to a Cisco Terminal Server. If the RNC9370 will be
connecting to a Cisco Terminal Server then the pin out outlined below will be required for
the console connection to work properly.
Contents
...................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC B-1
24-3005 UA08.1
Issue 3.01 October 2012
DB-9 to RJ45 adapter DB-9 to RJ45 adapter
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
B-2 Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
Appendix C: LED display
Overview
Purpose
This appendix provides the LED display information for CP cards, FP cards, and SP cards
passport.
Contents
...................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC C-1
24-3005 UA08.1
Issue 3.01 October 2012
LED display LED display
....................................................................................................................................................................................................................................
LED display
Card Status based on LED display
This topic applies to the CP cards, FP and the SP cards Passport has only one led active at
one time, no combination of green and red LEDs.
....................................................................................................................................................................................................................................
C-2 Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
Appendix D: Glossary
Overview
Purpose
This appendix provides the list of terms specific to the 9370 RNC commissioning.
Contents
Glossary D-2
...................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC D-1
24-3005 UA08.1
Issue 3.01 October 2012
Glossary Glossary
....................................................................................................................................................................................................................................
Glossary
Terms
The following table terms specific to the RNC commissioning.
Abbreviation
The following table lists the acronyms and abbreviations specific to the RNC
commissioning.
A Ampere
CC1 Communication Controller
CEC Canadian Electrical Code part I
CP Control Processor
DCPS Dual Core Packet Server
S
eDCPS Enhanced Dual Core Packet Server
GND GrouND
RNC Radio Network Controller
MDM Multiservice Device Management
MMS Mass Memory Storage
NE Network Element
NEC National Electrical Code
OAM Operation, Administration, Maintenance
OC-3 Optical Carrier level 3
OMC-B Centralized Node B implementation specific OAM center
OMC-R Centralized UTRAN OAM center
OMU Operation and Maintenance Unit
PIM Power Interface Module
....................................................................................................................................................................................................................................
D-2 Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
Glossary Glossary
....................................................................................................................................................................................................................................
Table D-2 Abbreviation (continued)
....................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC D-3
24-3005 UA08.1
Issue 3.01 October 2012
Glossary Glossary
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
D-4 Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
Appendix E: Report sheet
Overview
Purpose
This appendix provides the Report sheet which is to be maintained for 9370 RNC
commissioning.
Contents
...................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC E-1
24-3005 UA08.1
Issue 3.01 October 2012
Report sheet RNC Commissioning data sheet
....................................................................................................................................................................................................................................
In the Action following chart, "To Use? "column MUST be filled by the co-ordinator
before the site operation.
This Method applies to the 9370 RNC
....................................................................................................................................................................................................................................
E-2 Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
Report sheet RNC Commissioning data sheet
....................................................................................................................................................................................................................................
Comments:
Sign off:
Last Page
....................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC E-3
24-3005 UA08.1
Issue 3.01 October 2012
Report sheet RNC Commissioning data sheet
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
E-4 Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
Appendix F: Product
conformance statements
Overview
Purpose
This appendix presents the product conformance statements that apply to the
Alcatel-Lucent 9370 Radio Network Controller.
In regions such as North America and the European Union, the statements that are
required are determined primarily by national or multi-national regulations. However, in
some regions, contract terms determine the required statements.
The presence of the statement indicates that the product does comply with that statement
wherever it is required to do so.
Contents
...................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC F-1
24-3005 UA08.1
Issue 3.01 October 2012
Product conformance statements Regulatory requirement compliance
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
F-2 Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
Product conformance statements Compliance for Canada
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC F-3
24-3005 UA08.1
Issue 3.01 October 2012
Product conformance statements Compliance for Canada
....................................................................................................................................................................................................................................
Eco-Environmental Statements
Packaging collection and recovery requirements
Countries, states, localities, or other jurisdictions may require that systems be established
for the return and/or collection of packaging waste from the consumer, or other end user,
or from the waste stream. Additionally, reuse, recovery, and/or recycling targets for the
return and/or collection of the packaging waste may be established. For more information
regarding collection and recovery of packaging and packaging waste within specific
jurisdictions, contact the Alcatel-Lucent Environment, Health and Safety organization.
....................................................................................................................................................................................................................................
F-4 Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
Product conformance statements Compliance for China
....................................................................................................................................................................................................................................
Eco-Environmental Statements
Packaging collection and recovery requirements
Countries, states, localities, or other jurisdictions may require that systems be established
for the return and/or collection of packaging waste from the consumer, or other end user,
or from the waste stream. Additionally, reuse, recovery, and/or recycling targets for the
return and/or collection of the packaging waste may be established. For more information
regarding collection and recovery of packaging and packaging waste within specific
jurisdictions, contact the Alcatel-Lucent Environment, Health and Safety organization.
Material content compliance
The People's Republic of China Ministry of Information Industry has published a
regulation (Order #39) and associated standards regarding restrictions on hazardous
substances (China RoHS). Currently, the legislation requires all Electronic and
Information Products (EIP) to comply with certain labeling and documentation
requirements. Alcatel-Lucent products manufactured on or after 1 March 2007, that are
intended for sale to customers in the China market, must comply with these requirements.
In accordance with the People's Republic of China Electronic Industry Standard Marking
for the Control of Pollution Caused by Electronic Information Products
(SJ/T11364-2006), customers may access the Alcatel-Lucent Hazardous Substances Table
at (http://www.alcatel-sbell.com.cn/wwwroot/images/upload/private/1/media/ChinaRoHS.
pdf).
....................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC F-5
24-3005 UA08.1
Issue 3.01 October 2012
Product conformance statements Compliance for European Union
....................................................................................................................................................................................................................................
CE Marking Statement
This product has been CE-marked in accordance with the following European Directives:
Directive 1999/5/EC Radio and Telecommunication Terminal Equipment (R&TTE) of
the European Parliament and of the council.
Directive 2004/108/EC Electromagnetic Compatibility (EMC)
Directive 73/23/EEC Low Voltage Directive (LVD)
Directive 2002/96/EC Waste Electrical and Electronic Equipment (WEEE)
Directive 2002/95/EC Restriction of the use of certain Hazardous Substances in
Electrical and Electronic Equipment (RoHS)
EMC compliance
The equipment complies with the following EMC specifications:
EN 300 386 (Europe)
EN 55022 (Europe) Class B
EN 55024 (Europe)
....................................................................................................................................................................................................................................
F-6 Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
Product conformance statements Compliance for European Union
....................................................................................................................................................................................................................................
CB Report is issued by CSA and provides regulatory safety compliance to International
and European markets and covers the following standards:
IEC 60950-1 Information technology equipment - Safety - Part 1: General
requirements International Regulatory Safety Standard.
EN 60950-1 Information technology equipment - Safety Part 1: General requirements
European Standard Regulatory Safety Standard.
9370 RNC CB Report
Reference number: CB 154792-1889473
Certificate Reference: CA/8762M2/CSA
Eco-environmental Statements
Packaging collection and recovery requirements
Countries, states, localities, or other jurisdictions may require that systems be established
for the return and/or collection of packaging waste from the consumer, or other end user,
or from the waste stream. Additionally, reuse, recovery, and/or recycling targets for the
return and/or collection of the packaging waste may be established. For more information
regarding collection and recovery of packaging and packaging waste within specific
jurisdictions, contact the Alcatel-Lucent Environment, Health and Safety organization.
Recycling / take-back / disposal of products and batteries
Electronic products and batteries bearing or referencing the symbols shown below shall
be collected and treated at the end of their useful life, in compliance with applicable
European Union and other local legislation. They shall not be disposed of as part of
unsorted municipal waste. Due to materials that may be contained in the product and
batteries, such as heavy metals, the environment and human health may be negatively
impacted as a result of inappropriate disposal.
Note: For electronic products put on the market in the European Union, a solid bar
under the crossed-out wheeled bin indicates that the product was put on the market
after 13 August 2005.
....................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC F-7
24-3005 UA08.1
Issue 3.01 October 2012
Product conformance statements Compliance for European Union
....................................................................................................................................................................................................................................
Note: For batteries put on the market in the European Union, a chemical symbol Hg
(mercury), Cd (cadmium), or Pb (lead), or a combination of those symbols, beneath
the cross-out wheeled bin indicates that the battery contains the corresponding heavy
metals.
....................................................................................................................................................................................................................................
F-8 Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
Product conformance statements Compliance for United States
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC F-9
24-3005 UA08.1
Issue 3.01 October 2012
Product conformance statements Compliance for United States
....................................................................................................................................................................................................................................
Any modifications to this equipment are not permitted without review and official written
authorization from the specific Certification Body. Unauthorized changes may violate the
Product Safety Certification. Modifications or changes authorized by official CN/CNN
are assumed to have received prior approval from this lab.
Indoor applications
This equipment is intended for installation in restricted access locations where access is
controlled or where access can only be gained by service personnel with a key or tool.
Access to this equipment is restricted to qualified service personnel only.
Eco-Environmental statements
Packaging collection and recovery requirements
Countries, states, localities, or other jurisdictions may require that systems be established
for the return and/or collection of packaging waste from either the consumer or the end
user, or from the waste stream. Additionally, reuse, recovery, and/or recycling targets for
the return and/or collection of the packaging waste may be established. For more
information regarding collection and recovery of packaging and packaging waste within
specific jurisdictions, contact the Alcatel-Lucent Environment, Health and Safety
organization or Alcatel-Lucent Hazardous Waste Center technical support at (888)
539-2783.
Material content compliance
The following notification applies to Alcatel-Lucent products distributed for sale, resale,
or use.
This product, part, or both may include a lithium-manganese dioxide battery, which
contains very small amounts of a perchlorate substance. Special handling may apply.
For California
Perchlorate Material - special handling may apply. See www.dtsc.ca.gov/hazardouswaste/
perchlorate.
....................................................................................................................................................................................................................................
F-10 Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012
Index
A appendix
....................................................................................................................................................................................................................................
Alcatel-Lucent 9370 RNC IN-1
24-3005 UA08.1
Issue 3.01 October 2012
Index
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
IN-2 Alcatel-Lucent 9370 RNC
24-3005 UA08.1
Issue 3.01 October 2012