Professional Documents
Culture Documents
LL s160wc w2 1c
LL s160wc w2 1c
LL s160wc w2 1c
Features:
Descriptions:
◇ The S160 SMD LED is much smaller than lead frame type components, thus enable
smaller board size, higher packing density, reduced storage space and finally smaller
equipment to be obtained.
◇ Besides, lightweight makes them ideal for miniature applications, etc.
Applications:
Package Dimension:
LED Die
0.5
1 2 1 + 2
Polarity
1
0.7
0.2 0.6 0.2
Unit: mm
Cathode Mark Tolerance: ± 0.10mm
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ± 0.10mm (.004″) unless otherwise specified.
3. Specifications are subject to change without notice.
Power Dissipation PD 95 mW
Forward Current IF 25 mA
Reverse Voltage VR 5 V
Notes:
1. Luminous Intensity Measurement allowance is ± 10%.
2. θ1/2 is the off-axis angle at which the luminous intensity is half the axial luminous
intensity.
3. It use many parameters that correspond to the CIE 1931 2°. X, Y, and Z are CIE 1931 2°
values of Red, Green and Blue content of the measurement.
100 50
30
50
20
25
10
0
300 400 500 600 700 800 0
2.8 3.0 3.2 3.4 3.6 3.8 4.0
Wavelength λp (nm) Forward Voltage VF (V)
100 100
10 10
1 1 0 1 2 3
-60 -40 -20 0 20 40 60 80 100 10 10 10 10
Ambient Temperature Ta (℃) Forward Current IF (mA)
o
30
40
o
30 40
25 1.0 o
20 50
0.9 o
60
0.8 o
10 70
o
80o
0 0.7 90
0 20 40 60 80 100 0.5 0.3 0.10 0.2 0.4 0.6
Ambient Temperature Ta (℃)
Notes:
1. Color coordinates measurement allowance is ± 0.01.
2. One delivery will include up to two consecutive color ranks and three luminous intensity
ranks of the products the quantity-ratio of the ranks is decided by Luckylight.
Resistance to Tsld=260±5℃,
1 6 Min 25pcs 0/1
Soldering Heat Min. 5sec
H: +100℃ 5min ∫ 10
2 Thermal Shock 300 Cycles sec 25pcs 0/1
L: -10℃ 5min
H: +100℃ 15min ∫
Temperature
3 300 Cycles 5min 25pcs 0/1
Cycle
L: -40℃ 15min
High
4 Temperature 1000Hrs. Temp: 100℃ 25pcs 0/1
Storage
DC Operating
5 1000Hrs. IF=20mA 25pcs 0/1
Life
Low
6 Temperature 1000Hrs. Temp: -40℃ 25pcs 0/1
Storage
High
7 Temperature/ 1000Hrs. 85℃/85%RH 25pcs 0/1
High Humidity
3.2 Reflow soldering should not be done more than two times.
3.3 When soldering, do not put stress on the LEDs during heating.
3.4 After soldering, do not warp the circuit board.
4. Soldering Iron
Each terminal is to go to the tip of soldering iron temperature less than 260℃ for 5 seconds
within once in less than the soldering iron capacity 25W. Leave two seconds and more
intervals, and do soldering of each terminal. Be careful because the damage of the product is
often started at the time of the hand solder.
5. Repairing
Repair should not be done after the LEDs have been soldered. When repairing is unavoidable,
a double-head soldering iron should be used (as below figure). It should be confirmed
beforehand whether the characteristics of the LEDs will or will not be damaged by repairing.
6. Caution in ESD
Static Electricity and surge damages the LED. It is recommended to use a wrist band or
anti-electrostatic glove when handling the LED. All devices, equipment and machinery must be
properly grounded.