Professional Documents
Culture Documents
CHEM 254 Experiment 8 Phase Diagrams - Liquid Vapour Equilibrium For Two Component Solutions
CHEM 254 Experiment 8 Phase Diagrams - Liquid Vapour Equilibrium For Two Component Solutions
EXPERIMENT 8
𝑃𝐴 = 𝑥𝐴 𝑃𝐴0 and 𝑃𝐵 = 𝑥𝐵 𝑃𝐵0 where PA0 and PB0 are the vapour pressures of pure A and B
respectively and xA and xB are the mole fractions of A and B in the
liquid phase respectively
The partial pressures of each component can also be calculated using Dalton’s Law which gives the
relation between the mole fractions in the vapour phase (yA and yB) and the partial pressures.
𝑃𝐴 = 𝑦𝐴 𝑃𝑇 and 𝑃𝐵 = 𝑦𝐵 𝑃𝑇 (2)
𝑥𝐴 𝑃𝐴0 𝑥𝐴 𝑃𝐴0
𝑦𝐴 = = (3)
(𝑥𝐴 𝑃𝐴0 +𝑥𝐵 𝑃𝐵0 ) P0B +(P0A −P0B )𝑥𝐴
The dependence of total vapour pressure of an ideal solution on the mole fraction of A in the entire
system is shown in Figure 1.
pA *
liquid
a
pressure
Liquid +vapour
pB*
vapour
0.0 xA yA 1.0
mole fraction of A
Figure 1. Pressure versus composition diagram for a two component ideal solution
The composition of solutions can be determined by various techniques. One of these techniques is
refractormetry. A refractometer device is for the measurement of refractive index. The refractive index,
n, of a medium is defined as the ratio of the velocity of a wave in a vacuum to the phase velocity, vp in
the medium itself: n = c / vp
Figure 2. Scheme for Abbe Refractometry.
When the interface between the two mediums of different light speed (u) is flat, the angles of incidence
(i, in medium 1) and refracted (r, in medium 2), angle between the ray and a surface normal are
related through Snell's law:
Surface
normal
angle of angle of
incidence reflection
i
incident ray
air n
Interfa
ce Sample n
medium
r refracted ray
angle of
refraction
Purpose: In this experiment liquid - vapor equilibrium of a two component system will be studied.
Apparatus and Chemicals
Apparatus: Refractometer, boiling point apparatus with electrical resistance and condenser, variac,
labeled stoppered test tubes, thermometer, graduated cylinder, soft absorbent paper
Chemicals: Benzene, acetone.
Procedure
1. Place 15 mL of pure benzene into the distillation flask and set up the apparatus.
2. Open the condenser. Heat the sample very slowly. Adjust the transformer so that liquid boils
vigorously at a constant rate (3-4 mV AC). Continue to the boiling with the same rate until the
thermometer reading becomes constant.
4. Turn off the heater. After waiting for about one minute take about 1 mL of samples from the distillate
and the residue.
5. Transfer the samples into labeled test tubes for refractive index measurements.
6. Measure refractive index of both solutions. Caution: Do not touch the surface of the prism of Abbe
refractrometer with any glass or metal object. Do not scratch the prism surface. Clean the surface
of the prism using soft absorbent paper to keep it always free from dust and dirt.
7. Repeat the steps 2-6 after successive additions of 1.0, 3.0, 5.0 and 7.0 mL of acetone to the
residue in the distillation flask through the sampling port.
8. Repeat the experiment using acetone instead of benzene and benzene instead of acetone.
Treatment of data
1. a. Using the calibration curve given in Figure 2, find mole fractions of acetone and benzene in the
residue and distillate
1.42
1.41
1.4
1.39
1.38
1.37
1.36
1.35
0.5 0.6 0.7 0.8 0.9 1 1.1
Mole Fraction of Acetone
Figure 4. Calibration curve. Variation of refractive index as a function of mole fraction of acetone in
acetone-benzene mixtures.
b. Plot temperature versus composition graphs for both distillate and residue on the same graph.
b. Calculate mole fractions in the liquid and vapor phases using Raoult’s Law.
c. Plot temperature versus composition graphs for both distillate and residue on the same graph.
QUESTIONS
Group Number:
Student Name:
Date: Assistant name and signature:
Table1. Experimental data and mole fractions determined from the calibration curve
T(˚C) nR nD xA (D) xA (R) pA0 p B0
15 mL benzene
+ 1 mL acetone
+ 3 mL acetone
+ 5 mL acetone
+ 7 mL acetone
15 mL acetone
+ 1 mL benzene
+ 3 mL benzene
+ 5 mL benzene
+ 7 mL benzene
2.a. Calculate theoretical vapour pressures at each temperature and fill Table 1
2.b. Calculate mole fractions in the liquid and vapour phases using Raoult’s law and fill the following
Table 2.
𝑃𝑇 = 𝑥𝐴 𝑃𝐴0 + 𝑥𝐵 𝑃𝐵0
𝑃𝑇 = 𝑥𝐴 𝑃𝐴0 + 𝑃𝐵0 (1 − 𝑥𝐴 )
𝑃𝑇 𝑌𝐴 = 𝑥𝐴 𝑃𝐴0
Table 2. Theoretical mole fractions
T(˚C) pA pB xA yA
15 mL benzene
+ 1 mL acetone
+ 3 mL acetone
+ 5 mL acetone
+ 7 mL acetone
15 mL acetone
+ 1 mL benzene
+ 3 mL benzene
+ 5 mL benzene
+ 7 mL benzene