Professional Documents
Culture Documents
NN 20500 260
NN 20500 260
WMS
WMS
UNCONTROLLED COPY: The master of this document is stored on an electronic database and is “write
protected”; it may be altered only by authorized persons. While copies may be printed, it is not recommended.
Viewing of the master electronically ensures access to the current issue. Any hardcopies taken must be
regarded as uncontrolled copies.
ALCATEL-LUCENT CONFIDENTIAL: The information contained in this document is the property of Alcatel-Lucent.
Except as expressly authorized in writing by Alcatel-Lucent, the holder shall keep all information contained
herein confidential, shall disclose the information only to its employees with a need to know, and shall protect
the information from disclosure and dissemination to third parties. Except as expressly authorized in writing by
Alcatel-Lucent, the holder is granted no rights to use the information contained herein. If you have received
this document in error, please notify the sender and destroy it immediately.
PUBLICATION HISTORY
SYSTEM RELEASE: OAM07 and later
September 2012
Issue 01.04/EN, Standard
Update the Reference Documents
Dec 2009
Issue 01.03/EN, Preliminary
Update taken into account a new method to upgrade the firmware of a ST2540 Disk Array
(linked to the CR 221419.01)
Dec 2009
Issue 01.02/EN, Preliminary
Update taken into account a new firmware revision (XCP1091) with support of
CPU Jupiter+ @2.53Ghz
August 2009
Issue 01.01/EN, Preliminary
Update after review
July 2009
Issue 01.00/EN, Draft
Document creation
Copyright © 2009-2012 Alcatel-Lucent Alcatel-Lucent 9353 Management System - M5000 Firmware Upgrade
Publication history iii
TABLE OF CONTENTS
1. INTRODUCTION ................................................................................................1
1.1. APPLICABILITY ..........................................................................................................................1
1.2. AUDIENCE ................................................................................................................................1
1.3. PREREQUISITES........................................................................................................................1
Copyright © 2009-2012 Alcatel-Lucent Alcatel-Lucent 9353 Management System - M5000 Firmware Upgrade
Publication history v
LIST OF FIGURES
Copyright © 2009-2012 Alcatel-Lucent Alcatel-Lucent 9353 Management System - M5000 Firmware Upgrade
Publication history vii
LIST OF TABLES
Table 1 : XCP Release .............................................................................................................................5
Copyright © 2009-2012 Alcatel-Lucent Alcatel-Lucent 9353 Management System - M5000 Firmware Upgrade
1
1. INTRODUCTION
This document describes the firmware upgrade procedures for the OAM M5000 server
platform. It deals with the following upgrade:
XCP
OBP
This document describes the firmware upgrade procedures for the ST2540 Disk Array
controller.
1.1. APPLICABILITY
The procedures described in this document only apply for OAM M5000 just before
any installation/upgrade steps.
1.2. AUDIENCE
This document is intended for anyone who is responsible for upgrading the firmware
on the M5000.
The instructions provided here are for experienced System or Field Engineers with
Sun/Solaris knowledge.
1.3. PREREQUISITES
Copyright © 2009-2012 Alcatel-Lucent Alcatel-Lucent 9353 Management System - M5000 Firmware Upgrade
2
2. REFERENCE DOCUMENTS
[R1] NN-20500-002 Terminology
http://docs.oracle.com/cd/E19580-01/index.html
[R2] Sun SPARC® Enterprise M3000/M4000/M5000/M8000/M9000 Servers
XSCF User’s Guide
http://docs.oracle.com/cd/E20734_01/index.html
http://docs.oracle.com/cd/E19508-01/index.html
3. GENERAL DESCRIPTION
A M5000 with a firmware release different from the one tested in Alcatel-Lucent
labs may lead to failures and therefore requires one or more firmware upgrade.
A M5000 with lower firmware release is not supported and therefore requires
upgrade.
The following chapters detail the upgrade procedure for the XCP, OBP firmware and
ST2540 Disk array.
Copyright © 2009-2012 Alcatel-Lucent Alcatel-Lucent 9353 Management System - M5000 Firmware Upgrade
4
4. PROCEDURE DESCRIPTION
4.1. OVERVIEW
The version of the XCP/OBP firmware may change regularly for a number of reasons:
XSCF firmware
Determine the current XCP release with one of the following commands:
XSCF> getflashimage –l
Existing versions:
Version Size Date
FFXCP1081.tar.gz 42413986 Tue Apr 14 17:29:16 CEST 2009
The current XCP Firmware revision here is 1081
4.3.1 CONSTRAINTS
The server MUST BE STOPPED for the XCP upgrade/downgrade. OAM services are
therefore DOWN.
Copyright © 2009-2012 Alcatel-Lucent Alcatel-Lucent 9353 Management System - M5000 Firmware Upgrade
6
The XCP firmware release is available at “My Oracle Support” web site
http://support.oracle.com. After “Sign In” select the tab “Patches & Updates”.
Then search for the product “Sun SPARC Enterprise M5000 Server” on the Platform
“Oracle Solaris on Sparc (64-bit); and download the XCP firmware.
4.3.2 PREREQUISITES
Before proceeding with the upgrade, be sure:
That the server has been correctly and entirely backed up.
4.3.3 PROCEDURE
The following procedure is applied to perform an upgrade to the 1082 XCP release.
When the firmware is available in PE_FWM5000; in the other case follow Oracle
documentation.
Example:
<hostname> # cd /opt/nortel/tmp/PE_FWM5000
<hostname> # ftp <SRS_IPaddress>
name: oamops
password: <OamopsUser_password>
ftp> cd /opt/nortel/data/srs/DELIVERY/OAM/ALL/PE_FWM5000/Vxx_yy.Ezz
ftp> binary
ftp> get PE_FWM5000.Vxx_yy.Ezz.tar.*
ftp> bye
<hostname> #
<hostname> # cd /opt/nortel/tmp/PE_FWM5000
<hostname> # gzip -d PE_FWM5000.Vxx_yy.Ezz.tar.*
<hostname> # tar xfp PE_FWM5000.Vxx_yy.Ezz.tar
<hostname> #
Warn the users that the OAM server will be halted if this procedure is
applied on an OAM server.
- Reset XSCF
- Power on host
User can continue logon to host or XSCF when system starts up with
new firmware.
<hostname> # su - oamops
<hostname>(oamops) % /opt/nortel/shell/sysmgt/wam_stopall.sh
<hostname># su -
<hostname># /opt/nortel/shell/sysmgt/wam_stopSunMC.sh
Copyright © 2009-2012 Alcatel-Lucent Alcatel-Lucent 9353 Management System - M5000 Firmware Upgrade
8
Create a temporary and dedicated ftp user account. The ftp service
need also to be activated:
The user must connect to the server through its XSCF access.
From any administrative machine on the LAN , get the XSCF prompt
using the “oam” account:
4. Go back to the XSCF menu and wait until the showlogs displays a “SCF:XCP
update has been completed“ message:
XSCF>showlogs monitor
<... this is an example ...>
Dec 3 15:41:25 xxxxxxxx monitor_msg: SCF:XSCF download has been completed
(XSCFU=0, bank=1, XCP version=1091:last version=1090, Firmware Element ID=00,
version=01090001:last version=01090000)
Dec 3 15:41:38 xxxxxxxx monitor_msg: SCF:XSCF download is started (XSCFU=0,
bank=1, XCP version=1091:last version=1090, Firmware Element ID=01,
version=01090001:last version=01090000)
Dec 3 15:44:04 xxxxxxxx monitor_msg: SCF:XSCF download has been completed
(XSCFU=0, bank=1, XCP version=1091:last version=1090, Firmware Element ID=01,
version=01090001:last version=01090000)
Dec 3 15:44:14 xxxxxxxx monitor_msg: SCF:XSCF download is started (XSCFU=0,
bank=1, XCP version=1091:last version=1090, Firmware Element ID=02,
version=01080001:last version=01080001).../...
XSCF>showlogs monitor
Dec 3 15:47:38 xxxxxxxx monitor_msg: SCF:XSCF download has been completed
(XSCFU=0, bank=1, XCP version=1091:last version=1090, Firmware Element ID=05,
version=01090001:last version=01090000)
Dec 3 15:47:47 xxxxxxxx monitor_msg: SCF:XSCF download is started (XSCFU=0,
bank=1, XCP version=1091:last version=1090, Firmware Element ID=07,
version=01090001:last version=01080004)
Dec 3 15:47:48 xxxxxxxx monitor_msg: SCF:XSCF download has been completed
(XSCFU=0, bank=1, XCP version=1091:last version=1090, Firmware Element ID=07,
version=01090001:last version=01080004)
Dec 3 15:47:49 xxxxxxxx monitor_msg: SCF:XSCF bank apply has been completed
(XSCFU=0, bank=1, XCP version=1091:last version=1090)
Copyright © 2009-2012 Alcatel-Lucent Alcatel-Lucent 9353 Management System - M5000 Firmware Upgrade
10
Dec 3 15:47:50 xxxxxxxx monitor_msg: SCF:XCP update has been completed (XCP
version=1091)
5. Restart the domain to complete the OBP firmware update. Through the XSCF
access, connect as root user on the domain and stop it:
XSCF> console -d 0
Connect to DomainID 0?[y|n] :y
<hostname># init 0
...
{1} ok
< #. Allows to go back to the XSCF>
exit from console.
XSCF> poweroff -d 0
DomainIDs to power off:00
Continue? [y|n] :y
00 :Powering off
*Note*
This command only issues the instruction to power-off.
The result of the instruction can be checked by the "showlogs power".
XSCF> poweron -d 0
DomainIDs to power on:00
Continue? [y|n] :y
00 :Powering on
*Note*
This command only issues the instruction to power-on.
The result of the instruction can be checked by the "showlogs power".
XSCF> console -d 0
Connect to DomainID 0?[y|n] :y
{0} ok boot
The system will reboot with the new system firmware installed.
7. Delete the temporary ftp account and disable the ftp service:
<hostname> # su - oamops
<hostname>(oamops) % /opt/nortel/shell/sysmgt/wam_startall.sh
<hostname># /usr/sbin/prtconf -V
OBP 4.24.12 2009/10/30 06:59
Or
<hostname># /usr/sbin/prtdiag -v
...
Copyright © 2009-2012 Alcatel-Lucent Alcatel-Lucent 9353 Management System - M5000 Firmware Upgrade
12
4.4.1 CONSTRAINTS
No LUN managements are allowed during the upgrade of the firmware.
This procedure involves a ST2540 system reboot. It is mandatory to stop all OAM
services at the beginning of the firmware upgrade.
4.4.2 PREREQUISITES
Before proceeding with the upgrade, be sure:
That the server has been correctly and entirely backed up.
That the ST2540 has no hardware failure and there are two active controllers
card.
State: Okay
State: Okay
State: Okay
State: Okay
a u 16 8192 /dev/dsk/c1t0d0s7
a u 8208 8192 /dev/dsk/c1t0d0s7
a u 16400 8192 /dev/dsk/c1t0d0s7
a u 16 8192 /dev/dsk/c0t1d0s7
a u 8208 8192 /dev/dsk/c0t1d0s7
a u 16400 8192 /dev/dsk/c0t1d0s7
a u 16 8192 /dev/dsk/c1t1d0s7
a u 8208 8192 /dev/dsk/c1t1d0s7
a u 16400 8192 /dev/dsk/c1t1d0s7
<domainA hostname># luxadm display `luxadm probe | grep "Logical Path" | cut
-d: -f2-` | nawk '/Class/ || /State/ {print $0}'
Class secondary
State STANDBY
Class primary
State ONLINE
Class primary
State ONLINE
Class secondary
State STANDBY
Caution: If multipathing is not enabled, the system is not configured for a failover
operation. Before continuing with a live firmware upgrade, make sure the configuration
is set up for multipathing support.
The following actions allow checking that the two LAN links connected to the two
controller of the ST2540 are fully operational:
Copyright © 2009-2012 Alcatel-Lucent Alcatel-Lucent 9353 Management System - M5000 Firmware Upgrade
14
The following actions allow checking that the SUN CAM product is correctly activated
on the server:
rd
If not present, activate the CAM product located in /opt/Nortel/3 _party/CAM
The following actions allow checking that the SUN package including all necessary
firmware file is installed on the server:
CONTROLLER Procedure
<domain hostname>#
3. Verify the controller A and the controller B of the ST2540 are reachable on
the network:
Copyright © 2009-2012 Alcatel-Lucent Alcatel-Lucent 9353 Management System - M5000 Firmware Upgrade
16
Class secondary
State STANDBY
Class primary
State ONLINE
Class primary
State ONLINE
Class secondary
State STANDBY
The following table lists one of the installed firmware release after the upgrade:
See $4.4.2.4 for the command to execute to retrieve the firmware releases.
Copyright © 2009-2012 Alcatel-Lucent Alcatel-Lucent 9353 Management System - M5000 Firmware Upgrade
18
5. QUICK REFERENCE
{1} ok banner
Sun SPARC Enterprise M5000 Server, using Domain console
Copyright 2009 Sun Microsystems, Inc. All rights reserved.
Copyright 2009 Sun Microsystems, Inc. and Fujitsu Limited. All rights
reserved.
OpenBoot 4.24.12, 65536 MB memory installed, Serial #86374034.
<hostname> # /usr/sbin/prtconf –V
OBP 4.24.12 2009/10/30 06:59
<hostname> # /usr/sbin/prtdiag –v
...
6.1. ABBREVIATIONS
For the purposes of the present document, the following abbreviations apply:
6.2. DEFINITIONS
The XCP 1090 firmware is the first XCP release to support the XSCF command
showdateoffset.
The XCP 1090 firmware is the first XCP release to support the SPARC64 VII 2.53 GHz
processor. Earlier XCP firmware releases do not support this faster version of the processor,
which in other respects is functionally identical to all SPARC64 VII processors
The XCP 1091 firmware introduces the Active Directory and LDAP over SSL features.
Copyright © 2009-2012 Alcatel-Lucent Alcatel-Lucent 9353 Management System - M5000 Firmware Upgrade
20
UNCONTROLLED COPY: The master of this document is stored on an electronic database and is “write
protected”; it may be altered only by authorized persons. While copies may be printed, it is not recommended.
Viewing of the master electronically ensures access to the current issue. Any hardcopies taken must be
regarded as uncontrolled copies.
ALCATEL-LUCENT CONFIDENTIAL: The information contained in this document is the property of Alcatel-Lucent.
Except as expressly authorized in writing by Alcatel-Lucent, the holder shall keep all information contained
herein confidential, shall disclose the information only to its employees with a need to know, and shall protect
the information from disclosure and dissemination to third parties. Except as expressly authorized in writing
by Alcatel-Lucent, the holder is granted no rights to use the information contained herein. If you have
received this document in error, please notify the sender and destroy it immediately.