Professional Documents
Culture Documents
Especificaciones 226 B CAT Engine 3024C PDF
Especificaciones 226 B CAT Engine 3024C PDF
Valve lash
When the crankshaft is viewed from the front of the engine, the crankshaft rotates in the
following direction. ... Clockwise
When the camshaft is viewed from the front of the engine, the camshaft rotates in the
following direction. ... Clockwise
The front of the engine is opposite the flywheel end of the engine. The left side and the
right side of the engine are determined from the flywheel end. Number 1 cylinder is the
front cylinder of the engine.
Sistem distribution
4. Remove fasteners (3) . Identify the position of the different fasteners for
installation.
5. Carefully remove front housing (6) from plate (5) . Ensure that pin (2) remains
in the front housing.
Note: The front housing is aligned to the plate and to the cylinder block with
dowels.
3. Align pin (2) with hole (X) in oil pump cover (10) . Ensure that the oil pump
cover is concentric to idler gear assembly (11) .
5. Guide the linkage for the fuel injection pump into position so that the link is free
to move inside the aperture on the cylinder block for the fuel injection pump.
Align front housing (6) to the dowels in plate (5) . Install front housing (6) to
plate (5) .
8. Install a new O-ring seal (7) to front housing (6) . Position cover (8) on front
housing (6) and install nuts (4) and bolts (9) .
10. If the engine is equipped with a turbocharger, connect the hose to connection (1)
.
End By:
Standard free length for all C2.2 engines ... 35.0 mm (1.378 inch)
Service limit for the standard free length for all C2.2 engines ... 33.5 mm (1.319
inch)
Standard test force for all C2.2 engines ... 79 N (17.8 lb)
Service limit for the standard test force for all C2.2 engines ... 68.6 N (15.4 lb)
Length under test force for all C2.2 engines ... 30.4 mm (1.197 inch)
(A) Clearance between the exhaust valve and the valve guide
(A) Clearance between the inlet valve and the valve guide
Diameter of the exhaust valve stem for all C2.2 engines ... 6.940 to 6.955 mm
(0.2732 to 0.2738 inch)
Service limit ... 6.84 mm (0.269 inch)
Diameter of the inlet valve stem for all C2.2 engines ... 6.955 to 6.970 mm
(0.27382 to 0.27441 inch)
Service limit ... 6.89 mm (0.271 inch)
(B) Thickness of the valve head ... 0.925 to 1.075 mm (0.03642 to 0.04232 inch)
Exhaust valve
All C2.2 engines ... 1.94 to 2.16 mm (0.0764 to 0.0850 inch)
Service limit ... 2.5 mm (0.098 inch)
Inlet valve
All C2.2 engines ... 1.50 to 2.00 mm (0.0591 to 0.0790 inch)
Service limit ... 2.5 mm (0.098 inch)
Cylinder Head
The dowel pins in the cylinder block hold the cylinder head gasket in the correct
position when the cylinder head is installed.
(2) Cylinder head gasket
(3) The stamped marking on the cylinder head gasket must face upward. This ensures
that the cylinder head gasket is installed correctly.
Put clean engine oil on the threads of the cylinder head bolts. Tighten all of the bolts
finger tight. Tighten the bolts in the number sequence in Illustration 2.
Tighten the cylinder head bolts to the following torque. ... 101 N·m (75 lb ft)
Minimum distortion of the cylinder head ... 0.0 to 0.05 mm (0.000 to 0.002 inch)
Maximum distortion of the cylinder head ... 0.12 mm (0.005 inch)
Service limit ... 0.15 mm (0.006 inch)
Refer to Testing and Adjusting, "Cylinder Head - Inspect" for the procedures for
measuring the cylinder head.
(5) Piston height
Table 1
Piston Height Below Cylinder Block Thickness of Cylinder Head Gasket
Note: If the cylinder head has been machined, check the valve depth below the cylinder
head face. See Specifications, "Cylinder Head Valves". Before any work is done on the
valve seats, new valve guides must be installed.