Page 1 o
- VALLEY INTERNATIONAL TEST. PROCESS:
TEST PROCESS FOR LEVELLER TWO CHANNEL LIMITER
EE EEE EEE EEE EEE EEE EEE EE REEL EE EEE EEE EEE EEE EEE EE EEE ELEC EEE EEE EEE EEE EEEE EEE EEE
TTUPI>Connect the coordinator "SEND" te the Leveller "IN". Connect the
ceordinater "RETURN" to the Leveller "OUT
Set Tek. osc. (source A) freauency to 1kHz» level to OdB.
DSet coordinater as follows! Source R = 6003 Level = @ dBs Source = As
"Noise": "CMR", and "Wrap" switches down.
(1) Unit setup and rower check
Set front panel controls as follows? Threshold to full cws Gain to QdE
Integration Time te "Qut"s VU Select to Input. Be sure that "Link"
switch is cut. Set rear panel Input Cal switch to "QdB".
dCenter all trim pots (six per channel).
DAPP]Y AC Power and verify presence of +15v and -15v rower supplies
Verify that "POWER" led is on.
(2) Level checks :
Verify that output level is @dB +/- 242. Adjust Gain control for exac
QdB at cutrut.
>Set Ineut cal switch (on rear panel) ta "+4dB". Output should be —4de
Set Input cal switch te "-10dB", Outeut should be 10d8, Return Input
cal switch te Ode.
Turn Gain control from ccw to cw. Output should 9¢ fram -20dB to 20de
DIncrease input level on coordinator to 104B. Starting with Gain contr
centered: increase Sain until the "Ovid" led lights. Outrut should be
arrroximately 2248,
>Continue to increase Gain to the onset of clipping as observed on the
oscilloscore. Output should be at least 24dB.
Adjust Gain control for 21dB at output. Short tip and ring of output
Jack to Ground: one at a time. Output level drop should be less than 1
(3) VU meter trim
>Set input level on coordinater to Qdk. Adjust Gain.centrol for exact!
@d@ at output. Adjust VU Cal trim rot (accesible through front panel)
to read Bde on VU meter. Set VU Select switch te *Output". There sho
be no change in the VU'meter reading.
(4) Intermodulation distortion trim
>Apply IMD test signal at QdB to input (set asc. to 7kHz and press IMD
Test Signal buttens on analyzers Fress IMD Function butten). Adjust
Unity Dist trim pot for minimum distortion (.04% or less).
dIncrease input level on ceerdinater to 10dB and adJust Gain control fe
Q4f at cuteut. Adjust Gain Dict trim rot for .04% or less distortion.
(5) Noise test
Set asc. frea. te 100 Hz and release the IMD Test Signal switch. On t
analyzers press the Level Function switch. Set coordinator level ta @
Set the Gain contrel te QdB.
Set coordinater Noise switch to up. Outrut level should be ~77d2 or
less. Press the 4Q0Hz HI PASS filter switch on the analyzer. Output
should drop less than 3dB. Release the 400Hz HI PASS filter switch.
16) Cantrol rejection trim
t coordinator Noise switch to dewn and remove Flug from Le:
ler ink
Connect the tin of this rlu® through 2 1CQk ohm resister to UWIOF rin 2
(UPGE Tor cheanel 2. A Ctr] Res trim rat fer minimum cuteut
CF) Detector beiance tein
Return lug to Leveller ing Integration Time to "Fast". Se
UG rin & CUST® for chann ny just Det Bal trim pot for eau:/
o
ae
an
TEST PROCESS FoR LEVELUBR TWO CHANNEL LIMITER Page 2 of
Tw eshold trim
Seb ose. freq. to {kHz Set bntegatien Tine to ‘Out" and ad
controt for éxatly Pd8 at ovtrur.
Set integ/ation Time bo "Slow": turn Threshold full ccw, Set Thresh tr
pot built tw them vhile watching JW meters turn it slowly cow until
output Just begins €o drop chen turn it back until outrut just reach
input level te 20d (10d on ose. and 10dB on coordinator). If cut
Fut chan3ez lez: than +1dB er ~.5dBy 90 on to next ster. If nots
readjust Thresh trim rat for QUE at output. Change input level back to
Qe, (2. . and coordinater) and verity that .5d8 Gain
Reduction led goes eff. If it does nots slowly turn Thresh trim rot
Just enough to mabe it Go off. Now chanSe input level back to 20dB
(det o and 1042 on coordinator).
t Gain
en both a
Relea
test
>Verify that al) Gain Reduction leds are on.
Set Noise test swi , coordinater to up and verify that all Gain
Reduction leds 90 off in 2.5 to 3 seconds. Set Noise test switch on |
coordinator to down.
Anticipatery release test
DLecate .22uF mylar capacitor nearest rin 1 ef U103 (UZO3 on channel 2).
Connect score prabe to rearmost lead of this capacitors set score for
Sv/div.+ DC courleds and verify that voltege is arrroximately -i2vdc.
2Now turn Threshald contro? cw while watching score and verify that whil<
control is being turned the veltage increases and falls back te its
riginal value when rot is not being turned.
nect scare probe from Levellers
Limiter operation check
SSet Threshold control te +10dB, Output should be 13dB +/~ 2dB, Adjust
Threshold control fer exactly 13d2 at outrut. Gain Reduction meter
should read 7d8.
DChan®e osc. reaver 100Hz. Output should change less than 14B.
SSet Integration Time te "Fast". Outrut should increase by 2-44B and Ga
Reduction meter should read 4 or 3 dB.
Link te
Set csc. Treauency te IhHE
Set Threshold contre) to full ccw. Press the Link switch in, Gain
Reduction leds on adjacent channel should match those on the channel beir
tested.
urn Thre
se the Link switch.
hold contre) cu.
eras they @
Gain Reduction leds on the twa channels shou
tb Proc on channel 2.