Professional Documents
Culture Documents
Samsung LS17MJVKS
Samsung LS17MJVKS
4 Troubleshooting
4-1 Common Acknowledge
- If you change the interface board, be sure that the U105, U106 and U103 these three components also
changed to the new I/F board because there was program inside. If not, please re-write EDID or upload
firmware into Flash memory via VGA Cable.
- If you adjust clock and phase, please do it at the condition of Windows shut down pattern.
- If you confirm the R.G.B. color is normal or not, please do it under 16-grey scalar pattern.
- This LCM is analog interface. So if the entire screen is an abnormal color that means the problem
happen in the analog circuit part, if only some scale appears abnormal color that stand the problem
happen in the digital circuit part.
- If you check the H/V position, please use the crosshatch pattern.
- This LCM support more than 30 timing modes, if the input timing mode is out of specification, the picture
may appears abnormally.
- If brightness uneven, repairs Inverter circuit or change a new panel.
- If you find the vertical line or horizontal line lost on the screen, please change panel.
4-1
4 Troubleshooting
No power
Check pin3 of
Check R801, R805,
IC802 voltage
R822, R823, R817
about 1V
Check pin2 of
Check R803, R807,
IC802 voltage
R824, R825
about 2V
Check pin1 of
IC802 voltage is Check R812, R816, C818
5.8V
END
4-2
4 Troubleshooting
Check Vpin1-2 of
IC801 about
END
4-3
4 Troubleshooting
Unstable power
Check pin1 of
Check D806, C815
IC802 voltage is
if short
5.8V
END
4-4
4 Troubleshooting
No backlight
Yes
No Yes
No power supply to Check the cable that from
LED lamp is OK
inverter I/F BD to P/I BD is ok
Yes
Is there 14V No No
voltage on pin 3,4 U501, U502 fail Check power supply
of T501, T502
Is there PWM No
signal on pin 4 of Check I/F BD
IC501
Yes
Yes
No
Vsense voltage
Lamp connector opened
2.9V
No
Yes
Yes Yes
Pin 5 of IC501 Check R523, D504,
Feedback circuit failure
voltage is Low level R529, D507, R528, R533
Yes
END
4-5
4 Troubleshooting
Black Screen
Check power No
supply: Pin1, 2 of Power Fail
CN101
Yes
Yes
Yes
Check Reset No
Check C144, R172
(pin84) Of U105
Yes
Yes
No No
Check R167, Q106,
R108, R110
MCU Fail
4-6
4 Troubleshooting
White Screen
No
No
Yes Yes
Check VLCD Is Check LVDS Panel Fail
5V? Signals
No No
No
Yes
END
4-7
4 Troubleshooting
Bad Screen
No
No
Yes
Yes
4-8
6 Electrical Parts List
Level Loc. No. Code No. Description & Specification Q'ty SA/SNA
6-1
6 Electrical Parts List
Memo
6-2
9 Schematic Diagrams
9 Schematic Diagrams
- This Document can not be used without Samsung s authorization.
9-1 DC-DC
9-1
9 Schematic Diagrams
9-2 INPUT
9-2
9 Schematic Diagrams
9-3 TSUM16AL
9-3
9 Schematic Diagrams
9-4 POWER
9-4
9 Schematic Diagrams
9-5 INVERTER
9-5
9 Schematic Diagrams
9-6 KEYPAD
9-6