Professional Documents
Culture Documents
LTE Important Parameters and Switches PDF
LTE Important Parameters and Switches PDF
MO CellDlPcPdschPa
Parameter ID PdschPaAdjSwitch
Parameter Name PDSCHPAADJSWITCH
NE eNodeB
MML Command LST CELLDLPCPDSCHPA
MOD CELLDLPCPDSCHPA
Meaning Indicates the switch for adjusting the PA through power control on the
PDSCH. If this parameter is set to ON, the PA is adjusted dynamically
when the channel quality is extremely good or bad.
IsKey NO
Mandatory NO
Dynamic Attribute No
Feature ID LBFD-002016
Feature Name Dynamic Downlink Power Allocation
Value Type Enumeration values
GUI Value Range OFF(Off), ON(On)
Enumeration OFF~0, ON~1
Number/Bit
Unit None
Actual Value OFF, ON
Range
Default Value OFF(Off)
Recommended OFF(Off)
Value
Impact CellDlPcPdschPa
Parameter None
Relationship
Access Read & Write
Service No (And no impact on the UE in idle mode)
Interrupted After
Modification
Interruption Scope Not involved
Interruption Not involved
Duration (min)
Caution None
Validation of The parameter modification has no impact on the equipment.
Modification
Impact on Radio If this switch is on, the PA is adjusted. If this switch is off, the PA is not
Network adjusted.
Performance
Introduced in V100R002C00
Version...
Attribute Radio
Initial Value Default/Recommended
Setting Source
Parent topic: CellDlPcPdschPa
MimoAdaptiveSwitch
MO MimoAdaptiveParaCfg
Parameter ID MimoAdaptiveSwitch
Parameter Name MimoAdaptiveSwitch
NE eNodeB
MML Command LST MIMOADAPTIVEPARACFG
MOD MIMOADAPTIVEPARACFG
Meaning Indicates the switches related to adaptive MIMO.
LOFD-001003
Feature Name DL 2x2 MIMO
DL 4x2 MIMO
Value Type Bit field type
GUI Value Range ModeCOLoopSwitch(Open loop and Closed loop Switch),
ModeDivMuxSwitch(Diversity and Multiplexing Switch)
Enumeration ModeCOLoopSwitch~0, ModeDivMuxSwitch~1
Number/Bit
Unit None
Actual Value ModeCOLoopSwitch, ModeDivMuxSwitch
Range
Default Value Open loop and Closed loop Switch:off, Diversity and Multiplexing
Switch:on
Recommended Open loop and Closed loop Switch:off, Diversity and Multiplexing
Value Switch:on
Impact MimoAdaptiveParaCfg
Parameter None
Relationship
Access Read & Write
Service No (And no impact on the UE in idle mode)
Interrupted After
Modification
Interruption Scope Not involved
Interruption Not involved
Duration (min)
Caution None
Validation of The parameter modification has no impact on the equipment.
Modification
Impact on Radio The setting of this parameter determines the transmission modes that are
Network applicable to the UEs served by a multi-antenna eNodeB and hence affects
Performance the performance such as the throughput and coverage.
Introduced in V100R001C01
Version...
Attribute Radio
Initial Value Engineering Design
Setting Source
Parent topic: MimoAdaptiveParaCfg
DELTAMCSENABLED
MO CellUlPcDedic
Parameter ID DeltaMcsEnabled
Parameter Name DELTAMCSENABLED
NE eNodeB
MML Command LST CELLULPCDEDIC
MOD CELLULPCDEDIC
Meaning Indicates whether the transmit power of the UE is adjusted
In the message,
this indication occupies one bit. The value 0, which means disabled,
ROHCSwitch
MO PDCPROHCPara
Parameter ID ROHCSwitch
Parameter Name ROHCSwitch
NE eNodeB
MML Command LST PDCPROHCPARA
MOD PDCPROHCPARA
Meaning Indicates whether the eNodeB supports ROHC.
HighestMode
MO PDCPROHCPara
Parameter ID HighestMode
Parameter Name HighestMode
NE eNodeB
MML Command LST PDCPROHCPARA
MOD PDCPROHCPARA
Meaning Indicates the highest mode of ROHC operation.
Profiles
MO PDCPROHCPara
Parameter ID Profiles
Parameter Name Profiles
NE eNodeB
MML Command LST PDCPROHCPARA
MOD PDCPROHCPARA
Meaning Indicates the compression profile supported by the eNodeB.
DefDopplerLevel
MO INNERMEASSWITCH
Parameter ID DefDopplerLevel
Parameter Name DefDopplerLevel
NE eNodeB
MML Command MOD INNERMEASSWITCH
LST INNERMEASSWITCH
Meaning Indicates the default Doppler level. When the Doppler measurement switch
is shut down, parameters are set based on the default Doppler level.
IsKey NO
Mandatory NO
Dynamic Attribute No
Feature ID LOFD-00101502
Feature Name Dynamic Scheduling
Value Type Enumeration values
GUI Value Range CLASS_0(CLASS_0), CLASS_1(CLASS_1), CLASS_2(CLASS_2)
Enumeration CLASS_0~0, CLASS_1~1, CLASS_2~2
Number/Bit
Unit None
Actual Value CLASS_0, CLASS_1, CLASS_2
Range
Default Value CLASS_1(CLASS_1)
Recommended CLASS_1(CLASS_1)
Value
Impact INNERMEASSWITCH
Parameter None
Relationship
Access Read & Write
Service No (And no impact on the UE in idle mode)
Interrupted After
Modification
Interruption Scope Not involved
Interruption Not involved
Duration (min)
Caution None
Validation of The parameter modification has no impact on the equipment.
Modification
Impact on Radio Indicates the default Doppler level when the Doppler measurement switch
Network is shut down. The Doppler level and other associated factors affect the CQI
Performance report mode and reported parameters, and therefore affect the feedback
overhead on the uplink and throughput or coverage on the downlink.
Introduced in V100R001C01
Version...
Attribute Radio
Initial Value Default/Recommended
Setting Source
Parent topic: INNERMEASSWITCH
TtiBundlingSwitch
MO GlobalProcSwitch
Parameter ID TtiBundlingSwitch
Parameter Name TtiBundlingSwitch
NE eNodeB
MML Command LST GLOBALPROCSWITCH
MOD GLOBALPROCSWITCH
Meaning Indicates whether TTI bundling is enabled.
IsKey NO
Mandatory NO
Dynamic Attribute No
Feature ID LOFD-001015
Feature Name Enhanced Scheduling
Value Type Enumeration values
GUI Value Range OFF(Off), ON(On)
Enumeration OFF~0, ON~1
Number/Bit
Unit None
Actual Value OFF, ON
Range
Default Value OFF(Off)
Recommended OFF(Off)
Value
Impact GlobalProcSwitch
Parameter None
Relationship
Access Read & Write
Service No (And no impact on the UE in idle mode)
Interrupted After
Modification
Interruption Scope Not involved
Interruption Not involved
Duration (min)
Caution None
Validation of The parameter modification has no impact on the equipment.
Modification
Impact on Radio If TTI bundling is enabled for the UE, you can configure TTI bundling
Network through the UE to obtain more transmission chances within the delay
Performance budget on the VOIP air interface, improving uplink coverage.
Introduced in V100R001C01
Version...
Attribute Radio
Initial Value Engineering Design
Setting Source
Parent topic: GlobalProcSwitch
PdcchBndPcSw
MO CellDlpcPdcch
Parameter ID PdcchBndPcSw
NE eNodeB
Meaning Indicates the switch that is used to enable and disable power control
applied to the PDCCH carrying dedicated control information. If this
parameter is set to ON, the PDCCH power is adjusted dynamically when
the channel quality is extremely good or bad.
IsKey NO
Mandatory NO
Dynamic Attribute No
Feature ID LBFD-002016
Unit None
Impact CellDlpcPdcch
Parameter None
Relationship
Caution None
Introduced in V100R002C00
Version...
Attribute Radio
Parameter ID ReferenceSignalPwr
NE eNodeB
Meaning Indicates the reference signal power of the cell. For details, see 3GPP TS
36.213.
IsKey NO
Mandatory NO
Dynamic Attribute No
Feature ID LBFD-002003
LBFD-002009
LBFD-002016
Feature Name Physical Channel Management
Unit 0.1dBm
Recommended Value No recommended value. This parameter must be set based on the power
specification of the RRU and the cell bandwidth.
Impact PDSCHCfg
Parameter None
Relationship
Attribute Radio
Qam64 enabled
MO PUSCHCfg
Parameter ID Qam64Enabled
NE eNodeB
Mandatory NO
Dynamic Attribute No
Feature ID LOFD-001006
Unit None
Recommended Value No recommended value. The value should be set based on the 64QAM
capability of the UE.
Impact PUSCHCfg
Parameter None
Relationship
Caution None
Introduced in V100R001C00
Version...
Attribute Radio
UeTimerConst
This chapter describes the parameters related to the UeTimerConst MO.
Parameter ID IntraFreqMlbThd
NE eNodeB
Meaning Indicates the threshold that is used to trigger the intra-frequency load
balancing algorithm. When the cell load is equal to or lower than this
threshold, the intra-frequency load balancing algorithm is triggered or
stopped. This parameter is used with the load offset. That is, when the load
is higher than the load threshold plus the load offset, the algorithm is
triggered; when the load is lower than the load threshold, the algorithm is
stopped.
IsKey NO
Mandatory NO
Dynamic Attribute No
Feature ID LBFD-001001
LOFD-001032
Feature Name 3GPP R8 Specifications
Unit %
Default Value 60
Recommended Value 60
Impact CellMLB
Parameter The difference between the intra-frequency load balancing threshold and
Relationship the load offset should be greater than the DL cell dual-band intelligent
shutdown threshold. The sum of the intra-frequency load balancing
threshold and the load offset should be less than the DL admission load
threshold. The sum of the load balancing threshold and the load offset
cannot be greater than 100.
Access Read & Write
Caution None
Impact on Radio This parameter value has an obvious impact on the use of the MLB
Network algorithm. A greater parameter value may cause the MLB algorithm fail to
Performance take full effect when the cell is overload. A smaller parameter value may
cause too much signaling interaction and too many handovers.
Introduced in V100R002C00
Version...
Attribute Radio
SMeasure
MO HoMeasComm
Parameter ID SMeasure
NE eNodeB
Meaning Indicates the measurement threshold. When the quality of the serving cell
is higher than the threshold, the UE does not need to measure the intra-
frequency, inter-frequency, and inter-RAT neighboring cells. Thus, the
power consumption is reduced.
IsKey NO
Mandatory NO
Dynamic Attribute No
Feature ID LBFD-00201801
LBFD-00201802
LOFD-001019
LOFD-001020
LOFD-001021
LOFD-001022
LOFD-001022
Feature Name Coverage Based Intra-frequency Handover
SRVCC to UTRAN
SRVCC to UMTS
Value Type Interval values
Unit dBm
Impact HoMeasComm
Parameter None
Relationship
Caution None
Introduced in V100R001C00
Version...
Attribute Radio
Parameter ID RootSequenceIdx
NE eNodeB
MOD CELL
Meaning Indicates the logical root sequence index, which is used to derive the
preamble sequence. Each logical root sequence corresponds to a physical
root sequence. For the mapping between logical root sequences and
physical root sequences, see 3GPP TS 36.211.
IsKey NO
Mandatory YES
Dynamic Attribute No
Feature ID LBFD-002010
Unit None
Impact Cell
1) If 1 m <= cell radius <= 1 km, the value range of root sequence index is
24 to 819.
2) If 1 km < cell radius <= 1.5 km, the value range of root sequence index
is 30 to 815.
3) If 1.5 km < cell radius <= 2 km, the value range of root sequence index
is 36 to 809.
4) If 2 km < cell radius <= 2.6 km, the value range of root sequence index
is 42 to 803.
5) If 2.6 km < cell radius <= 3.5 km, the value range of root sequence
index is 52 to 795.
6) If 3.5 km < cell radius <= 4.3 km, the value range of root sequence
index is 64 to 789.
7) If 4.3 km < cell radius <= 5.5 km, the value range of root sequence
index is 76 to 777.
8) If 5.5 km < cell radius <= 6.8 km, the value range of root sequence
index is 90 to 765.
9) If 6.8 km < cell radius <= 8.6 km, the value range of root sequence
index is 116 to 751.
10) If 8.6 km < cell radius <= 10.6 km, the value range of root sequence
index is 136 to 729.
11) If 10.6 km < cell radius <= 13.2 km, the value range of root sequence
index is 168 to 707.
12) If 13.2 km < cell radius <= 17.2 km, the value range of root sequence
index is 204 to 659.
13) If 17.2 km < cell radius <= 21.5 km, the value range of root sequence
index is 264 to 629.
14) If 21.5 km < cell radius <= 27.8 km, the value range of root sequence
index is 328 to 561.
15) If 27.8 km < cell radius <= 32.8 km, the value range of root sequence
index is 384 to 513.
Note that the cell radius cannot be larger than 32.8 km if the cell is a high-
speed or super high-speed.
Access Read & Write
Interruption 0.1
Duration (min)
Caution None
Validation of The parameter modification takes effect after the cell is automatically
Modification reset.
Introduced in V100R001C00
Version...
Attribute Radio
Parameter ID PreambleFmt
NE eNodeB
MOD CELL
Meaning Indicates the preamble format used in the cell. For details, see 3GPP TS
36.211.
IsKey NO
Mandatory NO
Dynamic Attribute No
Feature ID LBFD-002010
Unit None
Actual Value Range 0~4
Default Value 0
Recommended Value 0
Impact Cell
Interruption 0.1
Duration (min)
Caution None
Validation of The parameter modification takes effect after the cell is automatically
Modification reset.
Introduced in V100R001C01
Version...
Attribute Radio
Parameter ID PhyCellId
NE eNodeB
MOD CELL
Meaning Indicates the physical cell ID. For details, see 3GPP TS 36.331.
IsKey NO
Mandatory YES
Dynamic Attribute No
Feature ID LBFD-002009
Unit None
Impact Cell
Parameter None
Relationship
Interruption 0.1
Duration (min)
Caution None
Validation of The parameter modification takes effect after the cell is automatically
Modification reset.
Introduced in V100R001C00
Version...
Attribute Radio
Parameter ID CellAdminState
NE eNodeB
Meaning Indicates the administration state, which can be Unblock, High block,
Middle block, or Low block.
IsKey NO
Mandatory YES
Dynamic Attribute No
Feature ID None
Unit None
Impact Cell
Parameter None
Relationship
Caution None
Introduced in V100R001C00
Version...
Attribute Radio
CellAlgoSwitch
This chapter describes the parameters related to the CellAlgoSwitch MO.
NE eNodeB
Meaning Indicates the switch of the SINR adjustment algorithm. This parameters
indicates whether the SINR measured value is adjusted according to the
ACK/NACK messages of the UL HARQ processes.
IsKey NO
Mandatory NO
Dynamic Attribute No
Feature ID LBFD-001006
Unit None
Default Value ON
Recommended Value ON
Impact CellUlschAlgo
Parameter None
Relationship
Caution None
Introduced in V100R002C00
Version...
Attribute Radio
NE eNodeB
Mandatory NO
Dynamic Attribute No
Feature ID LOFD-001016
Unit None
Impact CellUlschAlgo
Parameter None
Relationship
Caution None
Introduced in V100R002C00
Version...
Attribute Radio
Parameter ID UlschStrategy
Parameter Name Uplink Scheduling Strategy
NE eNodeB
Meaning Indicates the priority of the UL user scheduling algorithm and the policy of
arranging the priority of users. According to the Max C/I scheduling
policy, the UE with good-quality channels are scheduled, thus the spectral
efficiency is very high. The QoS of and fairness among users, however,
cannot be ensured. The Max C/I scheduling policy can be used to verify
the maximum capacity of the system. The fairest scheduling policy is RR.
When RR is used, the system capacity, however, is the smallest. Therefore,
RR is used only to verify the upper limit of the scheduling fairness in the
system. In application effects, the PF scheduling policy is between the
previous two policies. Thus, PF can be used to verify the capacity,
coverage, and fairness of the system. According to the EPF scheduling
policy, the features such as user QoS, system capacity, and channel
frequency selection are considered. The basic scheduling policy is used
during the performance test. In commercial scenarios, you are advised to
use the EPF scheduling policy.
IsKey NO
Mandatory NO
Dynamic Attribute No
Feature ID LBFD-002025
LOFD-001015
Feature Name Basic Scheduling
Enhanced Scheduling
Value Type Enumeration values
Impact CellUlschAlgo
Parameter None
Relationship
Caution None
Introduced in V100R002C00
Version...
Attribute Radio
Configuration of UL Hopping
MO CellUlschAlgo
Parameter ID UlHoppingCfg
NE eNodeB
Meaning Indicates whether frequency hopping (FH) is enabled or disabled and the
type and scheme used for FH.
IsKey NO
Mandatory NO
Dynamic Attribute No
Feature ID LBFD-002025
LOFD-001015
Feature Name Basic Scheduling
Enhanced Scheduling
Value Type Enumeration values
Unit None
Impact CellUlschAlgo
Caution None
Introduced in V100R002C00
Version...
Attribute Radio
Initial Value Setting Default/Recommended
Source
Parameter ID UlVmimoSw
NE eNodeB
Mandatory NO
Dynamic Attribute No
Feature ID LOFD-001002
Unit None
Impact CellUlschAlgo
Parameter None
Relationship
Caution None
Introduced in V100R002C00
Version...
Attribute Radio
Parameter ID PreAllocationSwitch
NE eNodeB
Mandatory NO
Dynamic Attribute No
Feature ID LOFD-00101502
Unit None
Default Value ON
Recommended Value ON
Impact CellUlschAlgo
Parameter None
Relationship
Caution None
Attribute Radio
Parameter ID McsAdaptHarqSw
NE eNodeB
Meaning Indicates the switch that is used to enable and disable UL adaptive HARQ.
If this switch is set to OFF, UL data is retransmitted by means of non-
adaptive synchronous HARQ. If this switch is set to ON, UL data is
retransmitted by means of adaptive synchronous HARQ. If this switch is
set to semi-ON, adaptive HARQ is triggered when a UL grant is delivered
to an HARQ process that is suspended because of, for example, resource
collision, activation of a measurement gap, or PDCCH congestion. Setting
this parameter to ON helps reduce resource consumption by
retransmission, increase the cell throughput, and prevent retransmission
conflicts. This, however, increases signaling overhead and therefore
consumes more PDCCH resources.
IsKey NO
Mandatory NO
Dynamic Attribute No
Feature ID LBFD-002006
Unit None
Impact CellUlschAlgo
Parameter None
Relationship
Caution None
Introduced in V100R002C00
Version...
Attribute Radio
FREQSELSW
MO CellDlschAlgo
Parameter ID FreqSelSw
NE eNodeB
Mandatory NO
Dynamic Attribute No
Feature ID LOFD-00101502
Feature Name Dynamic Scheduling
Unit None
Default Value ON
Recommended Value ON
Impact CellDlschAlgo
Parameter None
Relationship
Interruption No
Duration (min)
Caution None
Introduced in V100R001C00
Version...
Attribute Radio
DlScheSw
MO CellDlschAlgo
Parameter ID DlScheSw
NE eNodeB
Mandatory NO
Dynamic Attribute No
Feature ID LBFD-002025
LOFD-001015
Feature Name Basic Scheduling
Enhanced Scheduling
Value Type Enumeration values
Unit None
Impact CellDlschAlgo
Parameter None
Relationship
Interruption No
Duration (min)
Caution None
Validation of The parameter modification has no impact on the equipment.
Modification
Introduced in V100R001C00
Version...
Attribute Radio
Minimum RX level
MO CellSel
Parameter ID Qrxlevmin
NE eNodeB
Meaning Indicates the minimum required RX level. This parameter is used in the
formula of the cell selection criterion S.
IsKey NO
Mandatory NO
Dynamic Attribute No
Feature ID LBFD-001001
LBFD-002009
LBFD-00201803
Feature Name 3GPP R8 Specifications
Unit 2dBm
Impact CellSel
Parameter None
Relationship
Service Interrupted No (For the UE in idle mode, changes in this parameter affect cell
After Modification selection.)
Impact on Radio If this parameter of a cell is increased, it is more difficult for the cell to
Network meet criterion S and to become a suitable cell selected by a UE. If this
Performance parameter of a cell is decreased, it is easier for the cell to meet criterion S
and to become a suitable cell selected by a UE. The parameter should be
properly set so that the selected cells can provide signals that meet the
quality requirement of basic services.
Introduced in V100R001C00
Version...
Attribute Radio
MRO
This chapter describes the parameters related to the MRO MO.
Parameter ID GbrRbUseLowProportion
NE eNodeB
Meaning Indicates the allowed lowest proportion of resources (either the uplink or
downlink resources) to be occupied by GBR services. After an indication
of high resource usage by GBR services is reported, an indication of low
usage can be reported only when the proportion of resources currently
occupied by GBR services becomes lower than the value of this parameter.
IsKey NO
Mandatory NO
Dynamic Attribute No
Feature ID LBFD-001001
LBFD-002023
Feature Name 3GPP R8 Specifications
Admission Control
Value Type Interval values
Unit %
Recommended Value 99
Impact CellRacThd
Caution None
Attribute Radio
Parameter ID GbrRbUseHighProportion
NE eNodeB
Meaning Indicates the allowed highest proportion of resources (either the uplink or
downlink resources) to be occupied by GBR services. When
LCEM_RAC_ALG_GBR_USAGE_SWITCH is turned on, new GBR
services cannot be admitted if the proportion of PRB resources occupied
by the ongoing GBR services is higher than the value of this parameter.
IsKey NO
Mandatory NO
Dynamic Attribute No
Feature ID LBFD-001001
LBFD-002023
Feature Name 3GPP R8 Specifications
Admission Control
Value Type Interval values
Impact CellRacThd
Caution None
Impact on Radio A smaller value of this parameter results in a smaller quantity of resources
Network to be occupied by GBR services and a lower admission success rate of
Performance GBR services, thereby causing a higher probability of resource waste.
Parameter ID MaxNonGBRBearerNum
NE eNodeB
Meaning Indicates the maximum bearer number of non-GBR services in the cell.
IsKey NO
Mandatory NO
Dynamic Attribute No
Feature ID LBFD-001001
LBFD-002023
Feature Name 3GPP R8 Specifications
Admission Control
Value Type Interval values
Unit None
Impact CellRacThd
Parameter None
Relationship
Caution None
Impact on Radio A smaller parameter value indicates fewer admitted non-GBR services; a
Network greater parameter value indicates more admitted non-GBR services.
Performance
Introduced in V100R001C01
Version...
Attribute Radio
Parameter ID Qci1HoThd
NE eNodeB
Meaning Indicates the admission threshold for the handed-over service whose QCI
is 1. This threshold is applicable in both UL and DL.
Mandatory NO
Dynamic Attribute No
Feature ID LBFD-001001
LBFD-002023
Feature Name 3GPP R8 Specifications
Admission Control
Value Type Interval values
Unit %
Default Value 90
Recommended Value 90
Impact CellRacThd
Parameter 1. The sum of Qci1CongThd and CongRelOffset must be smaller than the
Relationship value of Qci1HoThd.
Caution None
Impact on Radio If the value of this parameter is too small, the admission threshold is too
Network low for the handed-over service whose QCI is 1. In this case, the QoS of
Performance the existing services cannot be guaranteed.
If the value of this parameter is too large, the admission threshold is too
high for the handed-over service whose QCI is 1. In this case, the
admission success rate is low for services with QCI of 1.
Introduced in V100R001C01
Version...
Attribute Radio
Parameter ID Qci1CongThd
NE eNodeB
Meaning Indicates the congestion threshold for services whose QCI is 1. This
threshold is applicable in both UL and DL.
When the satisfaction rate of services with QCI of 1 in the cell becomes
lower than this threshold, the services with QCI of 1 enter the congested
state.
When the satisfaction rate of services with QCI of 1 in the cell becomes
higher than the sum of this threshold and the congestion relief offset, the
services with QCI of 1 leave the congested state.
IsKey NO
Mandatory NO
Dynamic Attribute No
Feature ID LBFD-001001
LBFD-002024
Feature Name 3GPP R8 Specifications
Congestion Control
Value Type Interval values
Unit %
Default Value 65
Recommended Value 65
Impact CellRacThd
Parameter The sum of Qci1CongThd and CongRelOffset must be smaller than the
Relationship value of Qci1HoThd.
Caution None
Impact on Radio A larger value of this parameter indicates a higher probability of system
Network congestion. If the value is large, the system resource usage and the access
Performance success rate are low.
Attribute Radio
Parameter ID UlRbLowThd
NE eNodeB
MML Command MOD CELLRACTHD
Meaning Indicates the threshold that determines whether the UL resource block
(RB) usage is low. It is applicable to UL admission decision. If the MAC
layer reports that the UL RB usage is less than this threshold, you can infer
that the UL RB usage is low.
IsKey NO
Mandatory NO
Dynamic Attribute No
Feature ID LBFD-001001
LBFD-002023
LBFD-002024
Feature Name 3GPP R8 Specifications
Admission Control
Congestion Control
Value Type Interval values
Unit %
Default Value 90
Recommended Value 90
Impact CellRacThd
Parameter UlRbLowThd must be less than UlRbHighThd.
Relationship
Caution None
Impact on Radio A greater value of this parameter leads to the higher probability of
Network generating the low usage indication of UL resources resource blocks, thus
Performance causing excessive admission. The resource allocation, however, is
protected after the admission decision, and therefore this parameter does
not affect the QoS satisfaction rate of the whole system.
Attribute Radio
Parameter ID UlRbHighThd
NE eNodeB
Meaning Indicates the threshold that determines whether the usage of the UL
resource block (RB) is high. It is applicable to UL admission decision. If
the MAC layer reports that the usage of the UL RB is greater than this
threshold, you can infer that the UL RB usage is high.
IsKey NO
Mandatory NO
Dynamic Attribute No
Feature ID LBFD-001001
LBFD-002023
LBFD-002024
Feature Name 3GPP R8 Specifications
Admission Control
Congestion Control
Value Type Interval values
Unit %
Default Value 95
Recommended Value 95
Impact CellRacThd
Caution None
Impact on Radio A greater value of this parameter leads to the lower probability of
Network generating the high usage indication of UL resources resource blocks, thus
Performance causing excessive admission. The resource allocation, however, is
protected after the admission decision, and therefore this parameter is not
sensitive to admission. In addition, a greater value of this parameter may
cause slow load control.
Attribute Radio
LBFD-002024
Feature Name 3GPP R8 Specifications
Congestion Control
Value Type Interval values
GUI Value Range 0~50
Enumeration Not involved
Number/Bit
Unit %
Actual Value 0~0.50
Range
Default Value 20
Recommended 20
Value
Impact CellRacThd
Parameter 1. The sum of Qci1CongThd and CongRelOffset must be smaller than the
Relationship value of Qci1HoThd.
ANR
This chapter describes the parameters related to the ANR MO.
LST CELLMRO
Meaning Indicates whether to set the upper and lower limits of the CIO adjustment
range for the cell.
If this parameter is set to CFG, the CIO for the cell can be changed by an
amount within the range specified by the upper and lower limits. If this
parameter is set to NOT_CFG, the upper and lower limits of the CIO
adjustment range for the cell in intra-frequency MRO are calculated by
using the following formulas: Lower limit = Off + ofs + ocs - ofn + Hys -
5, Upper limit = Off + ofs + ocs - ofn + Hys -1, where Off is the offset for
intra-frequency handover, ofs and ofn are the frequency-specific offsets for
the serving frequency and neighboring frequency respectively, ocs is the
cell-specific offset for the serving cell, and Hys is the hysteresis for intra-
frequency handover. If this parameter is set to NOT_CFG, the upper and
lower limits of the CIO adjustment range for the cell in inter-frequency
MRO are calculated by using the following formulas: Lower limit = -24,
Upper limit = thresh + 110 - ofn + hys, where thresh is the RSRP threshold
for triggering a coverage-based inter-frequency handover and hys is the
hysteresis for inter-frequency handover.
IsKey NO
Mandatory NO
Dynamic Attribute No
Feature ID LOFD-002005
Feature Name Mobility Robust Optimization(MRO)
Value Type Enumeration values
GUI Value Range NOT_CFG(Not configure), CFG(Configure)
Enumeration NOT_CFG~0, CFG~1
Number/Bit
Unit None
Actual Value NOT_CFG, CFG
Range
Default Value NOT_CFG(Not configure)
Recommended None
Value
Impact CellMro
Parameter If the CioAdjLimitCfgInd parameter is set to CFG, the CioAdjLowerLimit
Relationship and CioAdjUpperLimit parameters need to be set.
LST CSFALLBACKHO
Meaning Indicates the time-to-trigger for event B1 that is used in CS fallback to
UTRAN. When CS fallback to UTRAN is applicable, this parameter is set
for UEs and used in the evaluation of whether to trigger event B1. When
detecting that the signal quality in at least one UTRAN cell meets the
entering condition, the UE does not send a measurement report to the
eNodeB immediately. Instead, the UE sends a report only when the signal
quality continuously meets the entering condition during the time-to-
trigger. This parameter helps decrease the number of occasionally
triggered event reports, the average number of handovers, and the number
of wrong handovers, and thus helps prevent unnecessary handovers. For
details, see 3GPP TS 36.331.
IsKey NO
Mandatory NO
Dynamic Attribute No
Feature ID LOFD-001033 / TDLOFD-001033
Feature Name CS Fall Back to UMTS / CS Fallback to UTRAN
Value Type Enumeration values
GUI Value Range 0ms, 40ms, 64ms, 80ms, 100ms, 128ms, 160ms, 256ms, 320ms, 480ms,
512ms, 640ms, 1024ms, 1280ms, 2560ms, 5120ms
Enumeration 0ms~0, 40ms~1, 64ms~2, 80ms~3, 100ms~4, 128ms~5, 160ms~6,
Number/Bit 256ms~7, 320ms~8, 480ms~9, 512ms~10, 640ms~11, 1024ms~12,
1280ms~13, 2560ms~14, 5120ms~15
Unit ms
Actual Value 0ms, 40ms, 64ms, 80ms, 100ms, 128ms, 160ms, 256ms, 320ms, 480ms,
Range 512ms, 640ms, 1024ms, 1280ms, 2560ms, 5120ms
Default Value 40ms
Recommended 40ms
Value
Impact CSFallBackHo
Parameter None
Relationship
Access Read & Write
Service No (And no impact on the UE in idle mode)
Interrupted After
Modification
Interruption Scope Not involved
Interruption Not involved
Duration (min)
Caution None
Validation of The parameter modification has no impact on the equipment.
Modification
Impact on Radio A larger value of this parameter results in a lower probability of handover
Network to the UTRAN cell, and a smaller value results in a higher probability.
Performance
Introduced in V100R002C00
Version...
Attribute Radio
Initial Value Radio Planning
Setting Source
Parent topic: CSFallBackHo
LST CSFALLBACKHO
Meaning Indicates the Ec/No threshold for event B1, which is used in CS fallback to
UTRAN. When CS fallback to UTRAN is required, this parameter is set
for UEs and used in the evaluation about whether to trigger event B1. This
parameter indicates the Ec/No requirement for the UTRAN cells to be
included in the measurement report. A UE sends a measurement report
related to event B1 to the eNodeB when the Ec/No in at least one UTRAN
cell exceeds this threshold and other triggering conditions are met. For a
cell with large signal fading variance, set this parameter to a large value to
prevent unnecessary handovers. For a cell with small signal fading
variance, set this parameter to a small value to ensure timely handovers.
For details, see 3GPP TS 36.331.
IsKey NO
Mandatory NO
Dynamic Attribute No
Feature ID LOFD-001033 / TDLOFD-001033
Feature Name CS Fall Back to UMTS / CS Fallback to UTRAN
Value Type Interval values
GUI Value Range -48~0
Enumeration Not involved
Number/Bit
Unit 0.5dB
Actual Value -24~0
Range
Default Value -13
Recommended -13
Value
Impact CSFallBackHo
Parameter None
Relationship
Access Read & Write
Service No (And no impact on the UE in idle mode)
Interrupted After
Modification
Interruption Scope Not involved
Interruption Not involved
Duration (min)
Caution None
Validation of The parameter modification has no impact on the equipment.
Modification
Impact on Radio A larger value of this parameter results in a lower probability of handover
Network to UTRAN, and a smaller value results in a higher probability.
Performance
Introduced in V100R001C00
Version...
Attribute Radio
Initial Value Radio Planning
Setting Source
Parent topic: CSFallBackHo
LST CSFALLBACKHO
Meaning Indicates the RSCP threshold for event B1, which is used in CS fallback to
UTRAN. When CS fallback to UTRAN is applicable, this parameter is set
for UEs and used in the evaluation about whether to trigger event B1. This
parameter indicates the RSCP requirement for the UTRAN cells to be
included in the measurement report. A UE sends a measurement report
related to event B1 to the eNodeB when the RSCP in at least one UTRAN
cell exceeds this threshold and other triggering conditions are met. For
details, see 3GPP TS 36.331.
IsKey NO
Mandatory NO
Dynamic Attribute No
Feature ID LOFD-001033 / TDLOFD-001033
Feature Name CS Fall Back to UMTS / CS Fallback to UTRAN
Value Type Interval values
GUI Value Range -120~-25
Enumeration Not involved
Number/Bit
Unit dBm
Actual Value -120~-25
Range
Default Value -106
Recommended -106
Value
Impact CSFallBackHo
Parameter None
Relationship
Access Read & Write
Service No (And no impact on the UE in idle mode)
Interrupted After
Modification
Interruption Scope Not involved
Interruption Not involved
Duration (min)
Caution None
Validation of The parameter modification has no impact on the equipment.
Modification
Impact on Radio A larger value of this parameter results in a lower probability of handover
Network to UTRAN, and a smaller value results in a higher probability.
Performance
Introduced in V100R002C00
Version...
Attribute Radio
Initial Value Radio Planning
Setting Source
Parent topic: CSFallBackHo
ENodeBAlgoSwitch
This chapter describes the parameters related to the ENodeBAlgoSwitch MO.