Professional Documents
Culture Documents
This RC boat hull building instruction goes hand-in-hand with the plans
available for download (use link below). The hull, and entire boat, is designed
to be a relatively easy project.
Before you email me asking if I think this is a suitable project for you, I'd like
to offer the following advice: Read through the building instructions and any
pages that it may link to and make your own guess first. I'm willing to bet
your guess will be better than mine anyways:)
Introduction
Read a short introduction to this new series of small RC model boats to learn
more, what materials you'll need etc.
Tools
Here are some of the tools I ended up using for building this RC boat hull.
Scissors
Steel straight-edge
Small square
Pencil
Glue
Next it's time to cut out the templates, starting with the bulkheads, transom,
keel, deck and chine shelf (Item "A").
A word of caution, don't cut too close to the outline at this point. You can
safely stay 1/16 (1.5mm) outside the perimeter of each part.
In addition, parts that get thinner in the middle or are generally "spindly",
(bulkheads #2, 3 and 4, keel, deck and chine shelf) are best not to cut out
the internal area for the template to maintain its integrity.
Leave 1/8" to 1/4" (3-6mm) between the outline of the parts. Once your
happy with the layout you can pencil in the outline of the templates onto the
balsa, or take a picture, so you remember where each piece go.
Use the Spray Mount adhesive to glue the templates in place. Follow the
instructions on the can.
At this point all templates should be glued to the balsa with the Spray Mount
Adhesive, essentially turning the templates into over-size sticky notes. Now
it's time to start cutting out the parts.
Separate each part from the sheet first by using a razor blade or X-acto knife
and a metal straight-edge. At this point don't worry about the templates,
except not to cut into them. This step is just to separate the pieces so they
can be trimmed later.
You don't need the straight-edge, but it is infinitely easier to make a cut if you
do, and the risk of slipping and cutting into a template is greatly reduced. If
you have a scroll saw or band saw it can be put to good use at this step.
As the pieces are separated from each other, there will be excess material
surrounding the templates. Now it's time to trim that down. I tend to do it in
successive steps and using the straight-edge as much as possible. The
resulting angles will be taken off at the final trim.
I also tend to start with the outside shape and do any internal areas last,
otherwise the pieces can break and split easily.
The best way to make two identical parts is to sandwich two sheets of wood
under the template and cut through the stack. Two issues emerge:
Next, leaving the other half oversize, glue it to the first half using two tiny
dots of CA glue. The amount of glue is relatively important - too much glue
and you won't be able to get them apart etc.
Making a perpendicular cut free hand on balsa is difficult. If you're just a little
off perpendicular the two halves will be different size and the whole point of
sandwiching the material is lost.
The way I do it is to trim the sandwiched parts until all you've got left is an
even 1/16" (1.5mm) of balsa surrounding the outline of the template. To get
to finished size I trim off the last bit with 80 grit sandpaper on a hard sanding
block. I often lay the balsa over the edge of my work table and that way have
an easier time keeping the angle straight.
Final Trim
With the exception of multiple parts from one template (as outlined above)
parts with straight edges are best cut to finished size with the knife and
straight-edge.
For rounded edges there will be excess material coming off as angles. This is
best dealt with using a wooden sanding block and 80 grit sand paper. Start at
the angled peaks and work your way around the perimeter.
When sanding, your strokes need to go in one direction only. from the
template side towards the back so you don't lift the template off the wood.
You can put some angle to it, but you get the general idea.
Here are all the parts for the RC boat hull with templates still attached.
The last thing to do is to trim mortises and the internal areas as mentioned
earlier. Once all done you should have a set of parts like in the picture above.
The best tools for the job is a small square and a sharp, relatively soft, lead
pencil.
A small square is used to transfer alignment and position marks to the balsa.
The parts that get the treatment are chine shelf, keel, deck, and transom.
Having the center line marked on the outside of the transom will help in
aligning the keel and rudder.
The other components need marks to give the relative position for the
bulkheads. Only one line is required per bulkhead, but I typically mark the
position for both edges so I don't have to remember if the bulkhead goes in
front of or behind the line. With two lines, I know the bulkhead goes between.
Dry fitting also helps you familiarize yourself with the pieces that make up an
assemble and help you figure out which order to attach the parts while
retaining good alignment and integrity.
First dry-fit of both chine shelf halves, transom and two knees.
The most important tool to make a straight hull is a flat surface to build it on.
It is good if you can drive pins into it, lay weights or use magnets to hold the
chine shelf down flat on the building board or table top.
Lay down the Hull Alignment Template on your building board and lay a sheet
of wax paper or plastic food film (Seran Wrap or similar) over to prevent the
model to stick to the template and your table. I've found the wax paper resist
CA glue better, so that's what I use.
Secure the sheets to the board with a method suitable for the type of building
board you're using - it can be pins, tape, weights etc.
Detail of the front end of the chine shelves on the building board. Three points line up perfectly: the stem,
bulkhead position and inner front edge.
When I built the prototype I didn't have the hull alignment template, so you'll
see the template is missing in the pictures on this page. Assembly should be
a lot easier and almost self explanatory with the template.
Align the two halves of the chine shelf on the hull alignment template. Pin or
weigh them down once they are in position. There three most important
places to check for proper alignment are:
If all three of these line up with the template, secure them in place to the
board and glue them together with a couple of drops of CA glue where they
join at the front.
There are a few other less important points that should line up, such as the
inner front edge and the lines drawn for the #1 bulkhead.
Drawing lines to high light the bulkhead positions.
Take a straight-edge and pencil and draw lines connecting the bulkhead
position marks you made from the templates to aid bulkhead placement later
on.
Earlier we marked both front and rear edge of the bulkheads onto the balsa.
Now I usually only connect one set of those tick-marks, using the other set as
a visual guide for bulkhead placement.
Place the transom (item "5") in-between the two chine shelf pieces and line it
up with even on the left and right hand side. Use the two knees (items "E") to
establish the correct angle for the transom. The knees should line up with the
inner edges of the chine shelf (see pictures), but their placement is not
critical.
Sometimes the parts will stay in place by themselves, other times they need
pins. Try and eliminate any gaps. Either way, once the placement is right,
attach the pieces with small drops of CA glue at the joints. Be careful not to
bump the parts out of position.
Next dry fit the stem piece (item marked "D") and bulkhead #1 and lay them
in position with stem piece centered on the hull center-line and the bulkhead
in it's marked position.
Check and make sure they are perpendicular to the building board and each
other. The position of the stem piece is more important than the bulkhead, so
pay extra attention to it. Once they're in position, glue them in place.
Take bulkhead #2 and align it as well. Check and make sure it is centered by
checking against the edge of the chine shelf - it should over/under-shoot
equally on either side. Where the tail end of the stem piece meet the
bulkhead is less important.
A bird's eye view of the rc boat hull so far.
Cut the two deck stringers from a 1/8" x 3/8" (or 3 x 10mm) balsa stick and
glue in place. You can leave it long at the transom end and trim it with an X-
acto Razor Saw for example.
The rc boat hull assembly is now fairly rigid and likely to stay straight and
true. In the next installment we'll focus on the deck, keel and lower part of
the hull structure before moving on to some internal installations and
planking.
In preparing the RC boat hull for the next step, you can now carefully remove
the structure from the building board. Don't worry if the wax paper sticks to
the hull or rips. Even if the wax paper looks clean and comes right off, I'd opt
to replace it for the next step. A spilled drop of glue or other debris can mess
you up, so better safe than sorry.
This is where we left off after the previous build log. If you missed it or would like to go back, click this
image.
Also, we're done with the hull alignment template that was placed under the
wax paper to guide component placement and alignment. However, if your
building board is really dark, or just ugly, you can lay the template upside
down under a fresh sheet of wax paper. It will provide a light, neutral
background when you build that makes it easier to spot things that are out of
the norm or things you drop or spill.
The Deck
After you remove the hull frame from the building board, remove any wax
paper remnants if any. Give the deck side of the structure a light sanding with
120 grit sandpaper backed with a flat sanding block. Go easy as the only
purpose is to take down any obvious high spots.
Put the hull frame aside while we focus on the two deck halves (item "B" on
the plans). Align them at the pinnacle of the stem and check alignment at the
rear edge where they join. At this point, place a piece of tape over the joint to
temporarily hold them together and flip the deck over with the tape facing
down. Pin or weigh the deck down on the building board.
Mark the bulkhead locations across the same way as you did on the chine
shelf. The lines will be a visual aid when aligning the deck to the hull.
Place the hull frame on top and position the raised part of the transom
inbetween the "legs" of the deck. When aligning the frame to the deck, the
stem is the most important, both in being centered and alignment front to
back.
Keep in mind that it is the top of the deck that after sanding should line up
with the profile angle of the stem piece, so looking at it all as assembled, the
frame will sit back a couple of millimeters from the foremost point on the
deck.
As the stem is lined up, glance at the bulkhead locations as marked on the
deck. Don't expect them all to line up perfectly, but it will give you a good
idea of how close to ideal you are at this point.
Also check and make sure the frame is making contact with the deck along
the deck stringers, transom, bulkheads and the stem piece. If care has been
taken so far in cutting out the parts and aligning, nothing should be too far
out of alignment.
When things look good place drops of thin CA along stem piece, bulkheads
and deck stringers.
We're going to take much of the tool requirements out of it and stop relying
on luck for success, here is how.
Keel cut to shape and two pieces of basswood or hard balsa for the propeller shaft tunnel.
To do this you need two pieces of basswood or hard balsa approximately 1/8
X 5/16 X 2 inches (3 X 8 X 50mm) that will act as doublers on either side of
the keel. Do as follows:
On the keel, we need to stay clear of the bulkhead #4 location, so make sure
the keel is well marked in that area. Next, lay the keel (template down) on a
flat surface and glue one doubler to the back side of the keel just ahead of
the #4 bulkhead location and line it up parallell with the bottom of the keel.
If you're off by a few millimeters from either that's fine. Try not to have the
doubler extend passed the bottom of the keel, it's better if you err on the
other side.
Next flip the keel over and trim away the area between the two phantom-
lines. This can be done with a razor blade and a straight edge or with a razor
saw. Try hard not to cut into the doubler.
The prototype used a 4mm outer diameter stuffing tube, so that's the size
marked on the drawing and template. Since the keel is made from 1/8" thick
material the tunnel you cut will be too tight from side to side. This can be
fixed later with a long 4mm drill or a needle file and some elbow grease.
Trim away the area of the keel where the propeller will pass through it, thus creating a tunnel for ditto.
Now peel away the template (make sure all bulkhead locations are transferred
first!) and place it on a flat surface with the attached doubler facing down.
Prop up either extreme of the keel with scraps of material until level and
clamp or place weights on top. Glue the second doubler in place and weigh or
clamp to the assembly.
Same rules apply as far as location - stay clear of bulkhead #4 location etc.
Propeller shaft tunnel finished - note faint pencil marks for bulkhead #4 just to the left of the doublers.
When I built the prototype it took me a while to figure this out, so they may
be missing in some of the pictures below.
Dry-fitting the keel with a square.
Time to fit the keel. Just like when the deck was attached, keeping the keel
perpendicular and centered is more important than locating front to back. The
easiest and best way to locate the keel front to back is to sand the front-most
part of the chine shelf flush to the angle of the stem piece. This way you'll
have an edge that should correspond with the front-most edge on the keel.
As you can see on the picture below, I didn't do it this way, but it would have
made things a little easier. Instead I eye-balled it in by looking at the profile
and having the curved part of the keel tangent the angle of the stem. Either
method works, but I highly recommend the former.
Transom and keel transition - note how the keel is lined up to the center line of the transom and flush at the
rear.
Also look at where the keel meets the transom. By design, the keel should
end at the stern face of the transom and be perfectly centered. Once all lines
up, attach the keel with a few drops of CA while held perpendicular and in
position.
The lower triangles that make up the rest of the bulkheads don't have
templates, but are taken off the triangular shape created between the keel
and chine shelf at each bulkhead location, or station as it is properly called.
First grab a piece of balsa a little wider than the height of the keel. At least
one of the long edges need to be straight. Use a square and make a cut at a
right angle to the straight edge.
Hold the square corner against the chine shelf and keel at station #3 with one
hand. With the other hand, with a sharp pencil, mark the edge where the keel
and chine shelf intersect (see picture below). All you need are two tick-marks.
A square corner of a balsa sheet is held against the hull at each station and the edge of chine shelf and keel
is marked on the balsa.
Lay the sheet down on your cutting surface and lay a straight-edge between
the two tick marks and cut with a razor blade or X-acto knife. You can save a
little time by using the first triangle at each station as a template for the
opposite side.
Lower bulkhead "triangles" in place at station #3.
All the lower bulkheads are cut out and glued into place.
Now the hull frame is ready for sanding to smooth out the shape some and to
give the skin more edge to hold onto. After that we'll start the planking
process.
The RC boat hull flipped over ready for sanding and planking.
The process isn't complicated, but may need a thorough break-down for the
novice. This page is meant to clarify the sanding and planking process for the
simple RC boat hull.
The hull needs sanding and final shaping before the planking can start.
You may or may not want to mark the edge of the chine shelf as well. I did
not on the prototype for some reason.
Tools
The only tools you need is some 80 to 100 grit sandpaper and a couple of
sanding blocks. In the picture above you'll see a razor plane. I only used that
to shape the lower part of the transom. I could just as well have used the
sand paper.
You also need a good sanding block. The one on the picture is technically too
wide, which made the sanding more difficult than it had to be. I'd recommend
a hard block about 3/4" wide.
A narrow block that is swept along the hull with one of the long sides leading
as its moved along the length of the hull will easier follow the changing
contour. Another option here is to make a sanding stick - essentially the same
thing, except the sandpaper is glued to the block/stick.
1. The shape and fairness of the deck, keel and chine shelf
2. The transition between bulkheads and deck and chine shelf (or
stringers, if any)
Using the magic marker, as described before, is my best effort to take care of
#1 above.
The illustration below shows the steps of sanding and planking in regards to
#2 above. The red dots show where attention is needed for each step. A red
line shows where a straight sanding block or stick has been used.
It may be hard to see in this picture, but the upper side panel (between the deck and chine shelf) has been
sanded, corresponding to #1 & 2 in the illustration above.
Notice how I lay the first joint between balsa sheets in the middle of bulkhead
#2. It will help hide the joint as there is less tension in the sheet from the
steep bend. Also make sure you alternate sides when you plank: lay a sheet
on the right, then the corresponding sheet on the left etc. It helps taking
asymmetrical tension out of the hull as you progress.
I determine the shape of each sheet by holding a roughly cut piece of balsa to
the hull with one hand and transferring the contour to the sheet with a pencil.
Then I trim the sheet with a razor blade to the line. Most often it requires a
couple iterations before I'm satisfied with the fit. Before I glue it in place with
CA glue, I try it on the opposite side. If it fits well I make a copy of it for the
other hand to save a little bit of time.
4: Sand Lower Panel
Sanding the lower panel is not that different from sanding the upper panel.
It's easy to tear out parts of the balsa planking on the upper panel if you're
not careful. You can lessen the risk of this happening by:
Just as in step one, the keel needs to be sanded to an edge as well to give
the planking some flat area to land on. Go easy and try and take material
equally off both sides. A narrow flat in the middle is OK.
The propeller shaft I made for this boat is identical to the one I made for this
plastic kit conversion, only a little longer - measure on the plan for actual
length. You can also use a commercial 2mm diameter prop shaft.
The planking is straight forward, just follow the same method as with the
upper panels.
Final sanding.
Later we will finish the hull by adding a keel strip, rub and spray rail.
The devil's in the details rings true even for RC boat hulls. Here we'll add
some of those so we can move onto the rudder installation.
It's made from a piece of 1/8" x 3/8" (3 x 10mm) balsa strip trimmed to
length.
Add a Coaming
A coaming is a raised edge that keeps water out. They also help locate the
hatch. I made mine from strip balsa 1/8" x 1/4" (3mm x 6mm), but the
height is not critical. I glued it in about 1/8" (3mm) proud of the deck.
On the picture below you'll see the scalloped trailing edge of the skeg. It
could be left straight, but I liked the slight arch.
For final shape the skeg was sanded both in profile and thinned toward the
propeller.
Keel Strip
Until now the planking along the keel has been left open, and it looks pretty
ugly. There are several ways to address, but my favorite is to glue in a strip of
basswood for additional reinforcement.
The gap at this point is an uneven "V" where the actual angle varies along the
length. First thing to do is to square it up by running a square needle file up
and down the joint.
As I file the groove, I dry-fit with a 1/16" (1.5mm) square basswood stick. In
the picture below you'll see it glued in place.
In the same picture, note how the upper edge of the hull planking (closest to
the table top) has a flat sanded to accommodate the rub rail which will be
fitted next.
Rub Rail
The rub rail consist of a 1/16 x 1/8 inch (1.5 x 3 mm) strip of basswood,
although most any hardwood strip of similar size will work. It can even be
made from styrene or laminated layers of card stock - your choice. Be sure to
sand a flat surface on the upper edge of the hull planking, perpendicular to
the deck. This surface should be as wide (vertically) as the strip is tall - in my
case 1/8" (3 mm).
I glued them on one at a time, starting with from the stern, the starboard
strip (right hand side) was glued in place first, as shown in the picture above.
Joining the strips at the stem can be tricky, but here is a tip.
Intuitively, most builders would aim for making a joint between the starboard
and port side strips, down the center line of the hull. This is not ideal for
several reasons: First, it's hard to do. Second, the strip is the most likely to
take a bump straight from the front and thus will see the most shock load
right where the joint is.
The second strip is also glued from the stern and gradually attached with CA
glue as I progress forward. I tried to make sure the strip is flush with the
deck as I went along.
Once at the stem, just continue the laying the strip passed the opposite side a
fair bit.
Spray Rail
The last thing to do before we move onto the rudder is to add a spray rail. I
wouldn't call it mandatory, but I believe it helps performance a little and it
certainly makes the boat look a lot better.
It's made from 1/16" (1.5 mm) square basswood strip. Again, a lot of
materials could be used, even hard balsa.
Attaching it is pretty straight forward. Starting from the transom and work
your way forward along the chine knee. At some point the knee will be less
defined and you need to establish the curve more or less by eye.
When I got to this point I took aim for an imaginary point at the stem where I
felt the strip made a curve that I liked and simply followed with the CA glue.
I'm sure there is a more scientific approach, but this worked well enough for
me.
I should point out that my spray strips ended up slightly off comparing left to
right, but I doubt anyone will ever notice. Below is a picture of how it ended
up.
Another thing I'd like to point out is that I did the tissue-and-dope before
adding the rub rail and spray strips. The CA glue has a hard time adhering to
the dense and hard lacquer finish, so I contemplated gluing the strips first
and then doing the tissue-dope.
After some valuable feedback (thanks Mike!), I'm back to the order presented
here. Adding tissue after the rails isn't just going to be a challenge getting the
tissue to conform to the rails, it will also shrink and pull away creating blisters
where the planking meets the rails - so, bad idea.
Surplus Mabuchi RE-280 to the left and Aristo-Craft RE-280 with a simple motor mount to the right.
Personally, I've always been in favor of a simple solution that gets the job
done. That's not to say I'd glue my motors into my boats. I do appreciate the
option to be able to remove or replace the motor easily, if need be.
Another thing to note is that I don't build high performance boats, so copy my
rubber-band mount for your Mega Power output brushless motor at your own
peril.
A homemade motor bed with the motor held in place with a rubber
band.
Universal joint
One of the most overlooked aspects when installing a motor in a model boat
is the alignment of the motor and propeller shaft. Too many builders believe
that because a compliant coupling is used having an angle between the two
shafts is OK. This is a misunderstanding.
Proper alignment between the motor and propeller shaft is paramount in model boat building. Note the
scratch-built motor mount.
The purpose of the compliant coupling is to relieve the motor from strain and
side loads due to misalignment. No motor installation is perfect, so the
misalignment that does occur should be kept to a minimum.
A model boat with a misaligned motor will suffer unnecessary power loss and
shorted life of the motor and coupling. The more power the motor generates
the more important the alignment becomes. That means:
In effect, most effected motor types are: high performance brushed motors,
all brushless and gas motors
The reason I like rubber bands for small motors is that they have high friction
against the motor can and prevent the motor from twisting. They also are
compliant and hold the motor with spring pressure. Compliance helps dampen
shock loads and is very resilient to vibrations compared to a more positive
type of mounting.
These RC model boats are based on an easy-to-build 15-inch long hard chine
hull mostly constructed from balsa. These boats would make great
introductions to both scratch building and RC boating.
You may wonder why I keep referring to this project in plural. The reason is,
this hull will become the basis for several simple semi scale model boats.
This is what the hull described here will look like when finished. It measures about 15 inches long by six
wide.
Being a planing hull the speed is high enough not to be boring, but not so fast
it would easily get out of control. Due to it's size it is suitable for calm ponds,
large fountains or pools. For safety reasons, don't run the boat in waters
where prohibited or where people or pets are in the water.
One word of caution; this project is not recommended for children or young
adults without adult supervision. If you are not comfortable using the tools
listed further down on this page, at the very least, ask someone for help.
This, and any other project on this site, is undertaken at your own risk.
The Plans
The plans for this boat was developed to be easy and inexpensive to build. If
you are interested in purchasing and downloading the plans, follow the link
above.
Material
The material used is mostly balsa, fiber board, basswood etc. A crucial aspect
for this project to be successful is that the weight is being kept down. I
strongly recommend that you don't substitute the materials recommended
here.
Below is a list of material needed for this RC boat hull and approximate
quantities. Material usage can vary widely from builder to builder. The
quantity listed is fairly generous and account for some do-overs.
1/8 x 4 inch wide x 36 inch long balsa - 2 sheets minimum + 1 extra for
superstructure. For those with access to metric sizes, substitute with 3 x 100
x 1000mm.
1/8 x 3/8 x 36 inch long balsa strip (just one needed) - 3 x 10 x 1000mm for
our metric friends.
1/16 x 3/16 basswood strip - one 36 or two 24 inch long - 1.5 x 5 x 1000mm.
One is technically enough, but see note on material quality.
1/16 x 1/16 basswood strip - one 36 or two 24 inch long - 1.5 x 1.5 x
1000mm. Again, see material quality note below.
For rudder and propeller shaft you will need stainless steel wire and some
brass rod. More about this later.
Generally, the balsa sheet should be relatively light-weight and soft, but most
importantly, straight grain and even density. It doesn't need to be the "ultra
light" stuff, but for this boat, avoid the heavy stuff. Also avoid warped or
bowed sheets. After a few boat projects you'll be a balsa expert.
For the balsa strips I'd go for a harder quality than the sheets (if available).
These strips will be used as structural stringers and for deck coaming, so
there are no bends or anything to consider. These strips could be substituted
for basswood or spruce if available in a pinch.
I've had mixed luck with basswood strips. I order most of my wood online and
thin basswood strips often has the grain run out the side of the strip causing
it to split when bending. For that reason I recommend getting several spares
if your ordering online. If you can pick them out yourself, you may be able to
avoid the duds and thus buy less.
Tools
Tools are often a matter of personal choice as there is often more ways than
one to skin a cat. I've tried to list the tools I've used for each step in the
building process.
Glue, Filler and Finishing
Glue - only thin CA glue has been used for this model boat
Hardware
There isn't much available in the US for building small RC boats like this. For
propeller I've come to use one plundered from a toy (I'll get into more detail
later in the build log).
For propeller shaft, stuffing tube, rudder etc. I opted to make them from
scratch out of brass tubing and sheet. It's not hard to do if you've got some
basic tools and the means and skill to solder with a basic solder iron. If not,
there are commercial alternatives, but we'll get into that later as well.
Propulsion
Build your own from balsa, styrene, popsicle sticks or other material at
hand
Buy the Crest or Aristo-Craft motor that come with a simple sheet
metal motor mount
I got a low cost, light weight 20A ESC from Hong Kong that I found on ebay.
Make sure the ESC is with "brake OFF" and comes with reverse.
The propeller is "on loan" from a Tamiya Submarine Motor (#70153). This is a
fairly common item and there are other brands and models. It's really not
ideal as the entire unit is junked except the prop. However, propellers this
size (3/4 inch diameter - about 20mm) are hard to come by in the US.
RC Controls
RC Controls are my trusted Tactic TTX-404 with a Hitec HS-55 sub micro
servo for steering.
Related Pages
Here is a list of links to related pages on this site:
Design Background - Learn more about the intent and goals for this RC
model boat
Plans
Build Logs
RC Boat Hull - part two - adding deck, keel and lower bulkheads
Hull Details - adding hatch coaming, skeg, rub and spray rails etc.