Professional Documents
Culture Documents
Civil PDF
Civil PDF
a) dummy b) event
c) activity d)constant
a) 12 hours b) 24 hours
a) aeration b) deoxygenation
a) 4 to 8 hours b) 8 to 12 hours
12. Maximum permissible colour for domestic supplies based on cobalt scale is
a) 5 ppm b) 20 ppm
a) 1 b) 7
c) 10 d)14
19. The normal average annual rainfall over the whole of India is estimated as
a) 88 cm b) 119cm
c) 217 cm d)290 cm
a) semicircular b) rectangular
22. An earthen embankment built on each side of a river, some distance away from its banks, to control
flood is called
c) Groyne d)spur
23. The best instrument for measuring the velocity of a stream flow is
a) 10 mm b) 20 mm
c) 30 mm d)40 mm
27. The weight per unit volume of a sample of soil mass is called
31. Two steel parts at right angles are weided with fillet weld of 10 mm size. The throat thickness of the
fillet weld should be
a) 7mm b) 10mm
c) 12mm d)5mm
c) 0.7 d d)2d
33. The minimum thickness of plates in a steel stack should be
a) 3mm b) 5mm
c) 6mm d)9mm
34. As per IS-800-1974, the maximum longitudinal pitch allowed in bolted joints of tension members is
about
c) low strength concrete but high tensile strength d)high strength concrete and high tensile
strength
36. Partial safety factors used for steel and concrete in limit state design are
37. A retaining wall retaining a surcharge, if overall height of the wall is H, then the width of the base
slab would be
a) 0.70 H b) 0.55 H
c) 0.50 H d)0.40 H
38. The ratio of maximum shear stress to average shear stress of a circular beam is
a) 2/3 b) 3/2
c) 3/4 d)4/3
39. The thickness of the flange of a tee beam of a ribbed slab is generally assumed as
a) 6mm b) 8mm
c) 10mm d)12mm
43. For concreting of heavily reinforced sections, that too without vibration, the compaction factor for
concrete should be
44. If the thickness is small in comparison with length and width, such structural members are called as
45. Number of unknown internal forces in each member of a rigid jointed plane frame is
a) 1 b) 2
c) 3 d)6
a) solid b) hollow
c) tapering d)composite
a) 400 b) 450
c) 500 d)550
a) 20 X 10 X 10 cm b) 23 X 12 X 8 cm
c) 19 X 9 X 9 cm d)18 X 9 X 9 cm
56. Number of compatibility conditions needed in the analysis of statically determinate structure
are
64.Minimum number of equilibrium equations required for a plane frames analysis of structure is
65. Minimum number of equilibrium equations required for a space frames analysis of structure
is
66.The measurement of all the work and supplies are recorded in the
(a) soil type (b)method of pile installation (c)pile spacing (d) all of these
75. Garbage is a
(a) Dry waste (b)Semi liquid waste (c)liquid waste (d) None of these
79.The solidification of molten magma within the earth crust results in the formation of
82.A good brick when immersed in water bath for hours , should not observe more than
(a) withstand high temperature (b) with stand high crushing pressure
(a) segmental arch (b) semi-circular arch (c) Bull’s eye arch (d) horse shoe arch
86.As the cement sets and hardens it generates heat which is called
(a) latent heat (b) sensible heat (c) heat of humidity (d) heat of hydration
(a) cube (b) cylinder (c) frustum of a cone (d) none of these
(a) 2.5 times the diameter of rivet hole (b) 3.0 times the diameter of rivet hole
(c) 2.0 times the diameter of rivet hole (d) 3.5 times the diameter of rivet hole
(c) working loads are completely resisted by prestressing force (d) none of these
(a) rain gauge (b) osmoscope (c) turbidimeter (d) all of these
(a) points (b)Diamond crossing (c) curves (d) Tracks for train
1. C 39. B 77. C
2. D 40. B 78. A
3. D 41. D 79. D
4. D 42. A 80. B
5. C 43. D 81. D
6. A 44. B 82. A
7. B 45. C 83. B
8. C 46. B 84. A
9. B 47. D 85. B
25. B 63. B
26. B 64. B
27. A 65. A
28. C 66. B
29. C 67. C
30. C 68. A
31. A 69. B
32. C 70. D
33. A 71. B
34. C 72. B
35. D 73. D
36. C 74. D
37. A 75. A
38. D 76. C