Professional Documents
Culture Documents
Hot Dip Galvanised PDF
Hot Dip Galvanised PDF
Hot-dip
galvanised
products
Product catalogue 49
Hot-dip galvanised products
General Grades
This section of the catalogue shows the standard
The hot-dip galvanised strip steel products offered grades of hot-dip galvanised steels offered by Corus.
in this section are listed below.
Typical applications
Page Steel • automotive components and body panels
50 General • steel framing
55 Galvatite for cold forming • roof and wall cladding (when painted or pre-finished)
61 Galvatite structural steel • components for building and construction
67 Galvatite high-strength steel • rainwater goods (when painted/coated)
• tubes and sections
• engineering components
• domestic appliances
• electrical goods
• components for agricultural machinery
50 Product catalogue
Hot-dip galvanised products
Corus will discuss these factors with the customer Coil width
to ensure compatibility with the quantity ordered. The coil width tolerances in table 7 on page 53 are from
EN 10143 :1993.
Particular products may have maximum coil weights
that differ from the range as a whole (see individual Flatness
product sections). Flatness complies with EN 10143 : 1993. Table 8 on
page 53 shows the flatness tolerances for steel grades
If a minimum coil weight has not been specified by the with ReL<280N/mm2. Table 9 on page 53 shows the
customer and agreed with Corus, then it will be 50% flatness tolerances for steel grades with ReL≥280N/mm2
of the agreed maximum weight. and <360N/mm2.
Edge camber
The deviation over a length of 2 metres will not exceed
6mm.
MB Zinc (Z) Minimised spangle Note: Coating mass shown in the table includes both surfaces.
improved surface
MC Zinc (Z) Minimised spangle
best quality surface
RA Iron-zinc (ZF) Regular, as coated surface
RB Iron-zinc (ZF) Regular improved surface
RC Iron-zinc (ZF) Regular best quality surface
Product catalogue 51
Hot-dip galvanised products
52 Product catalogue
Hot-dip galvanised products
Product catalogue 53
Hot-dip galvanised products
Surface quality C: Best quality surface Chemical passivation and oiling (CO)
This surface quality is obtained by temper rolling. The This combination of surface treatments increases
better side is suitable for the uniform appearance of a the degree of protection against white rust.
high-quality paint finish. The other side must at least
conform to surface quality B. Untreated (U)
Corus does not recommend that Galvatite be ordered
Inspected side in the untreated condition owing to the risk of white
As a rule, the upper side of the strip is inspected; rust formation during shipment and storage. However,
on request, the strip can be turned over so that the if untreated material is specified, it is supplied on the
underside is the inspected side. condition that the purchaser is responsible for any
corrosion arising from material ordered in the untreated
Surface texture condition.
All Galvatite products except those with a normal
spangle (NA) finish are available in several surface
textures. Unless the customer specifies otherwise,
Corus will supply a matt surface texture.
54 Product catalogue
Hot-dip galvanised products
Product catalogue 55
Hot-dip galvanised products
Table 15: Dimensions: EN 10142 : 2000 Table 16: Dimensions: EN 10142 : 2000
Z100, Z140: Coating finish NA Z100, Z140: Coating finish MA
Thickness Width Thickness Width
Max Max
> ≤ DX51D DX52D DX53D-56D > ≤ DX51D DX52D DX53D-56D
0.43 0.49 1420 1420 – 0.35 0.38 1270 – –
0.49 0.62 1420 1420 1250 0.38 0.40 1370 970 1200
0.62 0.63 1420 1420 1350 0.40 0.43 1370 1220 1250
0.63 0.70 1520 1520 1350 0.43 0.48 1520 1220 1250
0.70 1.00 1520 1520 1380 0.48 0.61 1520 1520 1350
1.00 1.25 1520 1520 1250 0.61 0.63 1525 1525 1350
1.25 2.00 1520 1520 – 0.63 0.66 1550 1525 1550
2.00 2.20 1375 1370 – 0.66 0.68 1650 1650 1550
2.20 2.50 1375 1220 – 0.68 0.70 1650 1650 1650
Note: Dimensions are in millimetres. 0.70 0.78 1780 1780 1750
0.78 0.80 1790 1790 1850
0.80 1.32 1820 1820 1850
1.32 1.40 1770 1770 1810
1.40 1.50 1700 1700 1730
1.50 1.60 1620 1620 1650
1.60 2.00 1470 1470 –
2.00 2.20 1375 1370 –
2.20 2.50 1375 1220 –
Note: Dimensions are in millimetres.
56 Product catalogue
Hot-dip galvanised products
Table 17: Dimensions: EN 10142 : 2000 Table 18: Dimensions: EN 10142 : 2000
Z100, Z140: Coating finish MB Z100, Z140: Coating finish MC
Thickness Width Thickness Width
Max Max
> ≤ DX51D DX52D DX53D-56D > ≤ DX51D DX52D DX53D-56D
0.50 0.55 1375 1400 1400 0.50 0.55 1350 1350 1400
0.55 0.61 1520 1520 1400 0.55 0.60 1520 1520 1400
0.61 0.66 1525 1600 1600 0.60 0.61 1520 1600 1600
0.66 0.70 1650 1650 1600 0.61 0.66 1525 1600 1600
0.70 0.79 1700 1750 1750 0.66 0.70 1650 1650 1600
0.79 1.50 1800 1800 1800 0.70 0.79 1700 1750 1750
1.50 1.61 1750 1750 1750 0.79 1.00 1800 1800 1800
1.61 1.71 1650 1650 1650 1.00 1.20 1800 1650 1550
1.71 1.81 1550 1550 1550 1.20 1.25 1650 1650 1550
1.81 1.91 1450 1450 1450 1.25 2.00 1375 1375 –
1.91 2.00 1400 1400 1400 Note: Dimensions are in millimetres.
Note: Dimensions are in millimetres.
Table 19: Dimensions: EN 10142 : 2000 Table 20: Dimensions: EN 10142 : 2000
Z200, Z225, Z275: Coating finish NA Z200, Z225, Z275: Coating finish MA
Thickness Width Thickness Width
Max Max
> ≤ DX51D DX52D DX53D-56D > ≤ DX51D DX52D DX53D-56D
0.43 0.49 1420 1420 – 0.40 0.50 1375 1375 –
0.49 0.62 1420 1420 1250 0.50 0.55 1375 1375 1250
0.62 0.63 1420 1420 1350 0.55 0.61 1520 1520 1250
0.63 0.70 1520 1520 1350 0.61 0.62 1525 1525 1250
0.70 1.00 1520 1520 1380 0.62 0.66 1525 1525 1350
1.00 1.25 1520 1520 1250 0.66 0.70 1650 1650 1350
1.25 2.00 1520 1520 – 0.70 1.25 1650 1650 1550
2.00 2.20 1375 1370 – 1.25 2.00 1375 1375 –
2.20 2.50 1375 1220 – 2.00 2.50 1375 – –
Note: Dimensions are in millimetres. Note: Dimensions are in millimetres.
Product catalogue 57
Hot-dip galvanised products
Table 21: Dimensions: EN 10142 : 2000 Table 22: Dimensions: EN 10142 : 2000
Z200, Z225, Z275: Coating finish MB Z200, Z225, Z275: Coating finish MC
Thickness Width Thickness Width
Max Max
> ≤ DX51D DX52D DX53D-56D > ≤ DX51D DX52D DX53D-56D
0.40 0.50 1350 1350 – 0.40 0.50 1350 1350 –
0.50 0.55 1375 1400 1400 0.50 0.55 1350 1400 1400
0.55 0.61 1520 1520 1400 0.55 0.60 1520 1520 1400
0.61 0.66 1525 1600 1600 0.60 0.61 1520 1600 1600
0.66 0.70 1650 1650 1600 0.61 0.66 1525 1600 1600
0.70 0.79 1700 1750 1750 0.66 0.70 1650 1650 1600
0.79 1.50 1800 1800 1800 0.70 0.79 1700 1750 1750
1.50 1.61 1750 1750 1750 0.79 1.00 1800 1800 1800
1.61 1.71 1650 1650 1650 1.00 1.20 1800 1650 1550
1.71 1.81 1550 1550 1550 1.20 1.25 1650 1650 1550
1.81 1.91 1450 1450 1450 1.25 2.00 1375 1375 –
1.91 2.00 1400 1400 1400 Note: Dimensions are in millimetres.
Note: Dimensions are in millimetres.
Table 23: Dimensions: EN 10142 : 2000 Table 24: Dimensions: EN 10142 : 2000
Z350: Coating finish NA Z350: Coating finish MA
Thickness Width Thickness Width
Max Max
> ≤ DX51D DX52D > ≤ DX51D DX52D DX53D-56D
0.43 0.63 1420 1420 0.35 0.38 1270 – –
0.63 2.00 1520 1520 0.38 0.40 1370 970 1200
2.00 2.20 1375 1370 0.40 0.43 1375 1220 1250
2.20 2.50 1375 1220 0.43 0.48 1520 1220 1250
Note: Dimensions are in millimetres. 0.48 0.61 1520 1520 1350
0.61 0.63 1525 1520 1350
0.63 0.66 1550 1550 1550
0.66 0.68 1650 1550 1550
0.68 0.70 1650 1605 1650
0.70 0.78 1780 1780 1750
0.78 0.80 1790 1790 1850
0.80 1.32 1820 1820 1850
1.32 1.40 1770 1770 1810
1.40 1.50 1700 1700 1730
1.50 1.60 1620 1620 1650
1.60 2.00 1520 1470 –
2.00 2.20 1375 1370 –
2.20 2.50 1375 1220 –
Note: Dimensions are in millimetres.
58 Product catalogue
Hot-dip galvanised products
Table 25: Dimensions: EN 10142 : 2000 Table 26: Dimensions: EN 10142 : 2000
Z350: Coating finish MB Z450, Z600: Coating finish NA
Thickness Width Thickness Width
Max Max
> ≤ DX51D > ≤ DX51D
0.40 0.50 1350 0.40 2.50 1375
0.50 0.69 1375 Notes: Dimensions are in millimetres.
0.69 0.79 1700
0.79 1.51 1800
1.51 1.61 1750
1.61 1.71 1650
1.71 1.81 1550
1.81 1.91 1450
1.91 2.00 1400
Note: Dimensions are in millimetres.
Product catalogue 59
Hot-dip galvanised products
60 Product catalogue
Hot-dip galvanised products
Product catalogue 61
Hot-dip galvanised products
Table 33: Dimensions: EN 10147 : 2000 Table 34: Dimensions: EN 10147 : 2000
Z100, Z140: Coating finish NA Z100, Z140: Coating finish MA
Thickness Width Thickness Width
Max Max
S220GD S280GD S350GD S550GD S220GD S280GD S350GD
> ≤ S250GD S320GD > ≤ S250GD S320GD
0.40 0.43 – – – 1070 0.38 0.43 1420 1420 –
0.43 0.45 1420 1420 – 1070 0.43 0.45 1520 1520 –
0.45 0.60 1420 1420 1400 1220 0.45 0.55 1520 1520 1400
0.60 1.00 1520 1520 1520 1220 0.55 0.61 1520 1520 1520
1.00 2.00 1520 1520 1520 – 0.61 0.66 1525 1525 1525
2.00 2.50 1375 1375 1375 – 0.66 1.25 1650 1650 1650
Note: Dimensions are in millimetres. 1.25 1.40 1620 1620 1520
1.40 1.60 1570 1570 1520
1.60 2.00 1520 1520 1520
Table 35: Dimensions: EN 10147 : 2000
2.00 2.50 1375 1375 1375
Z100, Z140: Coating finish MB
Note: Dimensions are in millimetres.
Thickness Width
Max
S220GD S280GD S350GD
> ≤ S250GD S320GD
0.38 0.43 1420 1420 –
0.43 0.45 1520 1520 –
0.50 0.55 1520 1520 1375
0.55 0.61 1520 1520 1520
0.61 0.66 1525 1525 1525
0.66 0.74 1650 1650 1650
0.74 0.79 1780 1650 1650
0.79 1.25 1820 1650 1650
1.25 1.40 1820 1620 1620
1.40 1.51 1820 1570 1570
1.51 1.60 1750 1570 1570
1.60 1.61 1750 1520 1520
1.61 1.71 1640 1520 1520
1.71 1.81 1550 1520 1520
1.81 1.91 1470 1520 1520
1.91 2.00 1400 1520 1520
2.00 2.50 1375 1375 1375
Note: Dimensions are in millimetres.
62 Product catalogue
Hot-dip galvanised products
Table 36: Dimensions: EN 10147 : 2000 Table 37: Dimensions: EN 10147 : 2000
Z100, Z140: Coating finish MC Z200, Z225, Z275: Coating finish NA
Thickness Width Thickness Width
Max Max
S220GD S280GD S350GD S220GD S280GD S350GD S550GD
> ≤ S250GD S320GD > ≤ S250GD S320GD
0.38 0.43 1420 1420 – 0.40 0.43 1375 1375 1375 1070
0.43 0.50 1520 1520 – 0.43 0.45 1420 1420 1375 1070
0.50 0.55 1520 1520 1350 0.45 0.60 1420 1420 1400 1220
0.55 0.61 1520 1520 1520 0.60 1.00 1520 1520 1520 1220
0.61 0.66 1525 1525 1525 1.00 2.00 1520 1520 1520 –
0.66 0.70 1650 1650 1650 2.00 2.50 1375 1375 1375 –
0.70 0.79 1700 1650 1650 Note: Dimensions are in millimetres.
0.79 1.20 1800 1650 1650
1.20 1.40 1620 1620 1620
1.40 1.60 1570 1570 1570
1.60 2.00 1520 1520 1520
2.00 2.20 1370 1370 1370
2.20 2.50 1220 1220 1220
Note: Dimensions are in millimetres.
Table 38: Dimensions: EN 10147 : 2000 Table 39: Dimensions: EN 10147 : 2000
Z200, Z225, Z275: Coating finish MA Z200, Z225, Z275: Coating finish MB
Thickness Width Thickness Width
Max Max
S220GD S280GD S350GD S550GD S220GD S280GD S350GD
> ≤ S250GD S320GD > ≤ S250GD S320GD
0.38 0.40 1420 1420 – – 0.38 0.40 1420 1420 –
0.40 0.43 1420 1420 1375 1070 0.40 0.43 1420 1420 1350
0.43 0.45 1520 1520 1375 1070 0.43 0.50 1520 1520 1350
0.45 0.55 1520 1520 1375 1220 0.50 0.55 1520 1520 1375
0.55 0.61 1520 1520 1520 1220 0.55 0.61 1520 1520 1520
0.61 0.66 1525 1525 1525 1220 0.61 0.66 1525 1525 1525
0.66 1.00 1650 1650 1650 1220 0.66 0.74 1650 1650 1650
1.00 1.25 1650 1650 1650 – 0.74 0.79 1780 1650 1650
1.25 1.40 1620 1620 1520 – 0.79 1.25 1820 1650 1650
1.40 1.60 1570 1570 1520 – 1.25 1.40 1820 1620 1620
1.60 2.00 1520 1520 1520 – 1.40 1.51 1820 1570 1570
2.00 2.50 1375 1375 1375 – 1.51 1.60 1750 1570 1570
Note: Dimensions are in millimetres. 1.60 1.61 1750 1520 1520
1.61 1.71 1640 1520 1520
1.71 1.81 1550 1520 1520
1.81 1.91 1470 1520 1520
1.91 2.00 1400 1520 1520
2.00 2.50 1375 1375 1375
Note: Dimensions are in millimetres.
Product catalogue 63
Hot-dip galvanised products
Table 40: Dimensions: EN 10147 : 2000 Table 41: Dimensions: EN 10147 : 2000
Z200, Z225, Z275: Coating finish MC Z350: Coating finish NA
Thickness Width Thickness Width
Max Max
S220GD S280GD S350GD S220GD S280GD S350GD S550GD
> ≤ S250GD S320GD > ≤ S250GD S320GD
0.38 0.40 1420 1420 – 0.40 0.43 1375 1375 1375 –
0.40 0.43 1420 1420 1350 0.43 0.45 1420 1420 1375 –
0.43 0.55 1520 1520 1350 0.45 0.60 1420 1420 1400 1220
0.55 0.61 1520 1520 1520 0.60 1.00 1520 1520 1520 1220
0.61 0.66 1525 1525 1525 1.00 2.00 1520 1520 1520 –
0.66 0.70 1650 1650 1650 2.00 2.50 1375 1375 1375 –
0.70 0.79 1700 1650 1650 Note: Dimensions are in millimetres.
0.79 1.20 1800 1650 1650
1.20 1.40 1620 1620 1620
1.40 1.60 1570 1570 1570
1.60 2.00 1520 1520 1520
2.00 2.20 1370 1370 1370
2.20 2.50 1220 1220 1220
Note: Dimensions are in millimetres.
Table 42: Dimensions: EN 10147 : 2000 Table 43: Dimensions: EN 10147 : 2000
Z350: Coating finish MA Z350: Coating finish MB
Thickness Width Thickness Width
Max Max
S220GD S280GD S350GD S220GD S280GD S350GD
> ≤ S250GD S320GD > ≤ S250GD S320GD
0.38 0.40 1420 1420 – 0.38 0.40 1420 1420 –
0.40 0.43 1420 1420 1375 0.40 0.43 1420 1420 1350
0.43 0.55 1520 1520 1375 0.43 0.50 1520 1520 1350
0.55 0.61 1520 1520 1520 0.50 0.60 1520 1520 1375
0.61 0.66 1525 1525 1525 0.60 0.69 1520 1520 1520
0.66 1.25 1650 1650 1650 0.69 0.78 1650 1520 1520
1.25 1.40 1620 1620 1620 0.78 0.79 1780 1620 1620
1.40 1.60 1570 1570 1570 0.79 1.40 1820 1620 1620
1.60 2.00 1520 1520 1520 1.40 1.51 1820 1570 1570
2.00 2.50 1375 1375 1375 1.51 1.60 1750 1570 1570
Note: Dimensions are in millimetres. 1.60 1.61 1750 1520 1520
1.61 1.71 1640 1520 1520
1.71 1.81 1550 1520 1520
1.81 2.00 1520 1520 1520
2.00 2.50 1375 1375 1375
Note: Dimensions are in millimetres.
64 Product catalogue
Hot-dip galvanised products
Table 44: Dimensions: EN 10147 : 2000 Table 45: Dimensions: EN 10147 : 2000
Z350: Coating finish MC Z450, Z600: Coating finish NA
Thickness Width Thickness Width
Max Max
S220GD S280GD S350GD S220GD S280GD S350GD
> ≤ S250GD S320GD > ≤ S250GD S320GD
0.38 0.43 1420 1420 – 0.40 2.50 1375 1375 1375
0.43 0.60 1520 1520 – Note: Dimensions are in millimetres.
0.60 0.69 1520 1520 1520
0.69 0.74 1650 1520 1520 Table 47: Dimensions: EN 10147 : 2000
0.74 0.78 1780 1520 1520 ZF100, ZF140: Coating finish RA
0.78 0.79 1780 1620 1620 Thickness Width
0.79 1.40 1820 1620 1620 Max
1.40 1.51 1820 1570 1570 S220GD S280GD S350GD
1.51 1.60 1750 1570 1570 > ≤ S250GD S320GD
1.60 1.61 1750 1520 1520 0.550 0.565 1490 1250 1250
1.61 1.71 1640 1520 1520 0.565 0.590 1490 1300 1300
1.71 1.81 1550 1520 1520 0.590 0.615 1490 1325 1325
1.81 2.00 1520 1520 1520 0.615 0.640 1500 1350 1350
2.00 2.20 1370 1370 1370 0.640 0.660 1500 1400 1400
2.20 2.50 1220 1220 1220 0.660 0.665 1550 1400 1400
0.40 2.50 1375 1375 1375 1.710 1.810 1530 1500 1500
Note: Dimensions are in millimetres. 1.810 1.830 1450 1500 1500
1.830 1.910 1450 1445 1445
1.910 2.000 1380 1375 1375
Note: Dimensions are in millimetres.
Product catalogue 65
Hot-dip galvanised products
66 Product catalogue
Hot-dip galvanised products
Product catalogue 67
Hot-dip galvanised products
68 Product catalogue