Professional Documents
Culture Documents
(Frame timber width 78 or 92) Horizontal section Shave profile in this area
26 26 26
scheme 541 26
(see also vertical section)
41 Eurogroove only
DEVENTER S 9555 DEVENTER S 9565 required for fittings
7,5 (or similar) (or similar)
7
8
18
12
BLR - Free dimension BLR - free dimension
18 FFB 18
37 for RHB 78 37 for RHB 78
51 for RHB 92 FB 4 FB 4 4 FB 51 for RHB 92
RAB
Scheme 431, 651, and 633 Vertical section Fix running track to the Vertical section
building at intervals of 500 mm
with gear DSG 3 top running (Drill on side) bottom running Because of their better load dispersal we
Chart to determine FB recommend bottom-running elements be
(only for stated frame sizes) given preference.
Scheme x for frame timber width 78 92
12
321, 330 FB= RAB x 22 50 4 x 30
3
18
431 FB= RAB ± x +4 24 General formular
4 4 x 30
42
541, 550, 532 FB= RAB +x 30 2 RAB + [(No. of sashes 1) 26] (2 BLR Free dimension)
5 FB=
43
No. of sashes
24
651, 633 FB= RAB + x 56 28
6
83
18
761, 770, 743 FB= RAB + x 82 54
7
4 x 30
18
12
28
22
Scheme Overview
18
bottom running bottom running
12
1 : 2,5 1 : 2,5
Folding-Sliding Door Fittings 12/18 - 9
A D220
B 1) Access through 1st folding sash
2 Folding sashes 2) e.g. As = Point A mirror image etc.
0 Main opening sash1)
FFH
• sturdy track with minimal threshold height
FH
• multiple adjusting options
• low threshold possible D
2)
A As A C
• smooth sliding action provided by ball bearing raced bogie wheels
RAH
B D B E
FFH
FH
2 Folding sashes 3 Folding sashes
1 Main opening sash 0 Main opening sash1)
2) Components for over rebate sizes 19 - 24 mm see Product Catalogue under FS Accessories.
D Ds 2)
2)
A C As A C C A C As 2)
12
B B D B B E 2)
18
Under no circumstances should the above size ranges be exceeded. 4 Folding sashes 5 Folding sashes 3+2 Folding sashes
1 Main opening sash 0 Main opening sash1) 0 Main opening sash1)
For the SIEGENIA-AUBI-Fitting FS-PORTAL the information given in DIN 68 121 (timber profiles for
windows and doors) is valid.
20
Scheme 651 Scheme 660* Scheme 633
12
18
26
OKFF
18
Advice for calculating sash widths A C C As
2)
A C C D220 A C Cs As
2)
4 x 30
2)
B B F B B BS B F Bs 2)
5 Folding sashes 6 Folding sashes 3+3 Folding sashes
24
To rationalise the door preparation, the size matrix shows all sashes to be the same width. This leads to 1 Main opening sash 0 Main opening sash1) 0 Main opening sash1)
over-folding of the door sashes so that they stack parallel at approx 95°.
OKFF
81
42
The following three options can apply if it is planned to stack the folded door sashes against a wall at 90°:
4 x 30
FSgb1003_3_08.03/0
43
FSgb1003
18
This reduces the over-folding.
– Use a wider vertical outer-frame section, possibly with an add-on profile, and a flat form of handle.
D D
2)
A C C As A C C C A C Cs As2) 4 x 30
2)
B B B D B B B E B B D Bs 2)
12
6 Folding sashes 7 Folding sashes 4+3 Folding sashes
1 Main opening sash 0 Main opening sash1) 0 Main opening sash1)
42,5
08.03 FSgb1003
Assembly (I) Assembly (II)
FS-PORTAL 12 mm airgap Assembly (I) FS-PORTAL 12 mm airgap Assembly (II)
in Profile set FS
19
20
23
20 22
21
A B C B D As
bottom top B C E C F As
running running
32 4 3 5 1 2 7 6 5 1 2 14 16 15 11
24
48 4 3 5 1 2 4 3 5 1 2
47
36 42 43 18 17 10
9 8 5 1 2
4 3 5 1 2
35
41
10
40 34 37
72 72 72 72 72
For hingeing with FS hinges and 50 50 50 50 50
packers .. see product catalogue
28 28 28 28
53
26 50 26 26 50 26
27
25 45 45 25 25 45 46 45 25
28 29 29 28 29
51 52 52 51 52
55 55 55 72 55
Parts List(I) (Surface TS Look) Parts List(II) (Surface TS Look)
FS-PORTAL 12 mm airgap Parts List(I) (Surface TS Look) FS-PORTAL 12 mm airgap Parts List(II) (Surface TS Look)
Materialnumber Part per scheme
321 330 431 541 550 532 651 633 761 770 743
Pos. Materialshorttext RAL 9003 dark mid
silver
white bronze bronze
FS PORTAL fittings
1-5 Carton sash hinge FS Cross section B 277423 278215 278208 278222 1 1 1 2 2 2 2 2 3 3 3
1-14 Carton bogie wheels D FS Cross section C 278277 278291 278284 278307 – 1 1 1 2 1 2 2 2 3 2
10,11
Carton bogie wheels FS Cross section D 278239 278253 278246 278260 1 – – 1 – 1 – – 1 – 1
15-18
19-23 Profile set FS Size RAB (mm)
250 to 2500 120989 120804 120798 137109
350 2501 to 3500 120996 120828 120811 137116 1 1 1 1 1 1 1 1 1 1 1
450 3501 to 4500 121009 120842 120835 137123
700 4501 to 6500 121016 120866 120859 137130
24 Seal HH0134-02 (17.5 m) 112977 1 1 1 1 1 1 1 1 1 1 1
Always required
50 Striker plate 56 A.... See profile data sheet 2...4 2...4 3 3...5 3...5 3...5 4 4 4...6 4...6 4...6
51 Striker plate S-ES A.... See profile data sheet 1 1 1 2 2 2 2 2 3 3 3
52 Tilt lock bearing S-ES FH A.... See profile data sheet 1 1 2 1 1 1 2 2 1 1 1
53 Striker plate A0767 for Pos. 46 711736 – – 0...2 – – – 0...2 0...2 – – –
Packaging Guide
FS-PORTAL 12 mm airgap Packaging Guide
Materialnumber
Pos. Quantity Materialshorttext RAL 9003 dark mid
silver
white bronze bronze
Assembly
Preparation
Pre-drill outer-frame for top hinges H-12 (34) and bottom hinges H-12/18 DH (31).
Prepare the required sash frame for the drive gear 3 (45).
See the specific assembly instructions for FAVORIT Si-line-timber.
Final Assembly
A Slide the Bogie wheels (10) into the Running rail (21).
B Assemble the row of folding sashes, starting with the sash nearest to the frame.
To install the bogie wheels (10) place vent setting blocks into frame rebate to give the correct airgap. Slide the bogie wheels
(10) into the support plates of Hinge D (8) and Hinge (17). With the locating nut in the correct position, see Diag. 2.
Tighten the pin of the bogie wheels (10) using allen key SW 5 and tighten locknut with
spanner SW 17 see Diag. 3.
C Slide Guide (11) into hinge D (6) and hinge (15), and tighten with spanner SW13
see Diag. 4.
SW 5 SW 13
Stellmutter
SW 17
Diag. 2 Bring locating nut into correct Diag. 3 Tighten pin L Diag. 4 Slide guide into support plate
positionand slide in bogie with allen key SW 5 and tighten and tighten with spanner
wheels locknut with spanner SW17 SW13
Assembly Instructions(II)
FS-PORTAL 12 mm airgap Assembly Instructions(II)
Galvanised and bichromated window screws for timber windows (not in product range)
Schemes Schemes
321, 541 and 761 431 and 651
Main opening door with
tilt and turn option on request
VS S-ES
Adjustments
2
mm
± 2,5 2 Positioning of the Sash hinges
-
Note: Slacken sash hinges in order,
adjust and re-tighten.
+ A Slacken both setscrews.
B Adjust the gap with allen key SW 4 .
SW 4
C Re-tighten setscrews..
3
Setting the height of Bogie wheels
SW 5
A Slacken lock nut SW 17 on the wheels.
- + B Adjust height of sash with 5 mm A/F hexagon
SW 17
socket head key.
Whilst doing this hold the clamping nut with a 17
mm A/F open ended spanner
3 C Then re-tighten the lock nut SW 17 keeping allen
key SW 5 firmly in place.
SW 13 ± 3,5 mm
Ø 7 mm
Ø 4,2 mm
=
ca. 100
Jig EB 644-4 for drill centring on the guide and running rails
Required: 1 off 143094
Drills: Ø 3,5
Important Notes
– The recommendations for profile section, Timber quality and design contained in DIN 68 121
(Timber profiles for windows and doors) is applicable to the SIEGENIA-AUBI-FS-PORTAL fittings.
The size limitations given on the front page must not be exceeded.
– It is possible that load bearing components can break due to overloading. This could result in a
folding sash becoming disengaged and causing serious injury. If due to special circumstances
(use in schools, nursuries,etc.)excessive loads can be expected, then precautions must be taken to prevent
straining of parts
– eg. by fitting a locking handle to prevent unauthorised usage.
Consult your SIEGENIA-AUBI sales advisor if you are unsure about anything in this respect.
– The hardware components made of steel, described in these Assembly Instructions are colourless
passivated and sealed to DIN EN 12329. They must not be installed for use in aggressive , corrosion
promoting air conditions, or on wood containing aggressive additives. If you have any doubts or
queries in these cases consult your SIEGENIA-AUBI-sales advisor.
– We can accept no liability in respect of damages or defects arising where the hardware assembly incor-
porates other products not manufactured by SIEGENIA-AUBI .
– Assemble the hardware components correctly as described in this instruction leaflet.
Details given for screw turns and torques are binding. Do not overtighten screws!
– Surface treatment must be performed prior to attachment of the hardware. Post treatment could adversely
affect the function of fittings; in this case we can accept no liability .
– Please follow the standard techniques for glazing and wedging of glass sealed units within the sash and
frame.
– Do not use any acid bonding sealants, as they can cause corrosion of the hardware components.
– Keep all rebates free of deposits and dirt - especially residues of cement or plaster. Avoid the direct effects
of wet on the hardware and contact of the
hardware with the cleaning materials.
– Affix a clearly visible copy of the user information Operating note: Operating note:
First open the access sash 1 . First open the access sash 1 .
to one of the folding sashes. The user information Swing the loose folding sash 2 Swing the loose folding sash 2
through 180° and enggage it. through 180° and enggage it.
stickers can be found in the cartons Bogie wheels Then open the other folding
sashes 3 and 4 etc.
Then open the other folding
sashes 3 and 4 etc.
FS and D FS. 3 2 1 1 2 3
Liability exclusion
4 3 1 1 3 4
Abbreviations
BLR Frame to sash clearance FFH Sash rebate height RHB Frame wood width
BS Hinge side FH Sash height S Stay
D/DF Side hung sash FS Fold & slide S-ES System security
DH With turn restraint H Wood U Bottom
DSG Slave sash drive gear HH Lift and slide-timber VS Locking side
E/EL Btm Hinge L Running rail VSU Locking side btm.
EB Drill jig MV Centre lock W Stay hinge
ED Side hung hinge O Top
F Folding sash OKFF Finished floor level
FB Sash width ON Without hardware grove
FEB Rebate corner hinge RAB Frame width
FFB Sash rebate width RAH Frame height