Professional Documents
Culture Documents
Estrella PDF
Estrella PDF
Mounting Star
Safety recommendations . . . . . . . . . . . . . . . . . . . . . 4
1. Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2. Components . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3. Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2 SKF TMDS 9
10. (Dis)Mounting procedures for shaft no. 6 . . . . . . . . . . . 15
10.1 Mounting bearing 21312 EK/C3 on shaft 6 . . . . . . . . 15
10.2 Dismounting bearing 21312 EK/C3 on shaft 6 . . . . . . . 15
SKF TMDS 9 3
Safety recommendations
– Never dismount a bearing from a tapered seating by means of the
Oil Injection Method without having an hydraulic nut or an SKF
locking nut screwed onto the shaft end.
4 SKF TMDS 9
1. Description
For a bearing to function properly and to last, it is important that the
correct mounting method and the suitable tools are being used. Care
should also be exercised with regard to cleanliness. Mounting should,
whenever possible, be carried out in a clean and dust-free room and not
in the immediate vicinity of dust producing machines. If the bearing is to
be re-used, dismounting must be conducted with the appropriate care.
SKF TMDS 9 5
2. Components
Component Designation Qty
1) Shaft no. 1 TMDS 9-11 1
2) Shaft no. 2 TMDS 9-12 1
3) Shaft no. 3 TMDS 9-13 1
4) Shaft no. 4 TMDS 9-14 1
5) Shaft no. 5 TMDS 9-15 1
6) Shaft no. 6 TMDS 9-16 1
7) Shaft no. 7 TMDS 9-17 1
8) Shaft no. 8 TMDS 9-18 1
9) Shaft no. 9 TMDS 9-19 1
10) Intermediate ring 1 (Shaft 2) TMDS 9-20 1
11) Intermediate ring 2 (Shaft 2) TMDS 9-21 1
12) Disc (Shaft 2) TMDS 9-22 1
13) Distance ring 1 (Shaft 5) TMDS 9-23 1
14) Distance ring 2 (Shaft 6) TMDS 9-24 1
15) Support ring (Shaft 5 + 6) TMDS 9-25 1
16) Stool (Shaft 7) TMDS 9-26 1
17) SNL 509 TG (Shaft 7) TMDS 9-27 1
18) Dismounting adapter (Shaft 7) TMDS 6-28 1
19) Turning Table 2072609 TMDS 9-29 1
3. Tools
Description Designation Qty
20) Hydraulic Handpump 729124 SRB 1
21) Hydraulic Nut HMV 12E 1
22) Electronic Induction Heater TMBH 1 1
23) Electronic Thermometer TMDT 2 1
24) Mechanical Fitting Tool TMFT 33 1
25) Bearing Puller Set TMMD 61 1
26) Bearing Puller TMMA 3 1
27) Locknut Spanner TMHN 7 1
28) Aluminium Heating Ring TMBR NU2212EC 1
29) Feeler Gauge 729865 A 1
30) Hook Spanner HN 13 1
31) Quick Connections Nipple 729100 3
32) Mounting Fluid LHMF 300/5 1
33) Dismounting Fluid LHDF 900/5 1
34) Split Collet Puller Set TMSC 30-60 1
35) Dial Indicator TMCD 5P 1
36) Lock Nut Socket TMFS 10 1
37) Hook Spanner HN 12 1
38) Hook Spanner HN 8 1
39) High Pressure Pipe 721740 A/300 1
40) Nipple 227963 1
41) Strong Back Puller TMBS 50 1
6 SKF TMDS 9
4. Bearings and Accessories
Bearing Qty Accessory Qty
21312 EK/C3 3 H 312 1
21312 E/C3 1 AHX 312 1
6208 1 KM 12 2
6212 1 MB 12 2
6214 1 KM 10 1
1209 EKTN9/C3 1 MB 10 1
6308 1 H 209 1
7308 BECBP 2 ASNH 509 1
NU 2212 ECP 1 MB 8 1
KM 8 1
KM 13 1
SKF TMDS 9 7
5.2 Dismounting of bearing 6208 on shaft no. 1 (1)
Select the correct combination of puller arms and withdrawal screw from
ball bearing puller TMMD 61, according to the instruction for the tool.
Insert the arms between the bearing rings, place the withdrawal screw
in position and dismount the bearing.
8 SKF TMDS 9
6. (Dis)Mounting procedures for shaft no. 2
SKF TMDS 9 9
6. (Dis)Mounting procedures for shaft no. 2
10 SKF TMDS 9
7. (Dis)Mounting procedures for shaft no. 3
SKF TMDS 9 11
8. (Dis)Mounting procedures for shaft no.4
12 SKF TMDS 9
8.2 Dismounting bearing 21312 EK/C3 on shaft no. 4
Connect pump 729124 SRB via
quick connection nipple 729100
to the shaft end. By pumping oil
into the oil duct and distribution
groove, an oil film will appear
between bearing inner ring and
shaft. Release the oil pressure by
turning the release valve at the
pump. Use hook spanner HN 12
to loosen and remove shaft nut
KM 12 and locking washer
MB 12. Rescrew the shaft nut so
far that a gap of about two
coarses of the thread is left
between the bearing and the nut. Tighten the release valve of the pump
again and build up a new oil film between bearing inner ring and shaft.
The bearing will simply be shot off from its seating with force and
without damaging the seat.
SKF TMDS 9 13
9. (Dis)Mounting procedures for shaft no. 5
14 SKF TMDS 9
10. (Dis)Mounting procedures for shaft no. 6
SKF TMDS 9 15
11. (Dis)Mounting procedures for shaft no. 7
16 SKF TMDS 9
12. (Dis)Mounting procedures for shaft no. 8
Shaft no. 8 will show the big differences in dismounting forces between
ball bearing 6212, which will be dismounted without Oil Injection
Method, and ball bearing 6214, which will be dismounted with Oil
Injection Method.
SKF TMDS 9 17
12.2 Dismounting ball bearing 6214 on shaft no. 8
Place bearing puller TMMA 3 around ball bearing 6214 and release the
spring of the puller. Connect high pressure pipe with adapter on the
shaft. Connect the quick connection nipple to the adapter and connect
pump 729124 SRB to quick connection nipple and pump oil between
bearing and bearing seat until oil escapes at the end of the contact
surface all around the shaft. While pumping, dismount the bearing by
means of the puller.
18 SKF TMDS 9
13. (Dis)Mounting procedures for shaft no. 9
SKF TMDS 9 19
In line with our policy of continuous development of
our products we reserve the right to alter any part of
the above specification without prior notice.
MP546E