Professional Documents
Culture Documents
Grundfos Pompe PDF
Grundfos Pompe PDF
HS
Installation
Mechanical installation 26
General installation guidelines 26
Vibration dampers 27
Expansion joints 27
Location 27
Foundation 27
Grouting 27
Measuring instruments 28
Piping 28
Suction piping 29
Discharge piping 31
Auxiliary piping 31
2
Introduction HS
Variants
Grundfos HS pumps are available in these variants:
• pump with motor and base frame
• bare shaft pump with base frame
• bare shaft pump.
3
Applications HS
Commercial systems
Industrial systems
Liquid transfer and pressure boosting in:
• process cooling and chilled water systems
GR 2910
• water condensing systems and cooling towers
• boiler feed and condensate systems
• industrial heating systems Fig. 3 HS pump in sprinkler irrigation
• washdown and cleaning systems
• industrial processing systems (water, light
chemicals, oils, etc).
Water distribution
Liquid transfer and pressure boosting in:
• public waterworks
• non-potable water systems.
4
Features and benefits HS
5
Performance range HS
Grundfos HS pumps are available with 2-, 4- or 6-pole 1. Go into the relevant performance range chart.
motors. 2. Find your duty point.
The next three pages show the performance range 3. Note which pump type covers your duty point.
covered by these three motor types. 4. Go to section “Product range” and then to
“Performance curves and technical data” and find
Knowing your required duty point, use the performance
more detailed information on your chosen pump.
ranges like this:
HS 2-pole
500
Q [m³/h]
Q [l/s]
2-pole, 60 Hz
400
HS
125-100-305
80 90 100
300
125-100-280
250
70
60
200
100-80-242
50
150
40
30
100
80
65-50-242
20
60
50
40
9 10
30
8
25
7
6
20
200
150
120
100
80
60
50
40
30
20
[m]
H
1000
900
800
700
600
500
400
300
200
p
6
p H
[kPa] [m] HS
250 4-pole, 60 Hz
2000 200 HS 4-pole
350-250-630
150
200-150-508
1000 100 35
0-
200-150-483 25
300-200-489 0-
49
800 80 8
150
600 - 125 20
60 - 381 0-
15 25 30
0- 0- 0-
125-100-381 38 20
0
25
500 50 1 - 38 0-
38
1 1
65-50-331 100-80-356
400 40
Performance range
300 125-100-305
20
0-
15
0-
25 30 30
5C 0-
65-50-242 25
0-
200 20 30
5
100-80-242 400-350-397
15
150-125-305 250-200-305
100 10
80 8
60 6
125-100-280
50 5
200-150-305A
40 4
20 25 30 40 50 60 80 100 150 200 250 300 400 500 600 800 1000 1500 2000 3000 4000
Q [m³/h]
6 7 8 9 10 20 30 40 50 60 70 80 100 200 300 400 500 700 Q [l/s]
7
8
p H
[kPa] [m] HS
100 6-pole, 60 Hz
900
HS 6-pole
800 80
700 350-250-630
600 60
500 50
200-150-483 200-150-508
400 40
300-200-489 350-250-498 350-300-508
300 30
Performance range
200 20
300-250-381
15
250-200-381
12
400-350-397
100 10
90
300-250-305
80 8
70
60 6
50 5
40 4
80 100 150 200 250 300 400 500 600 800 1000 1500 2000 2500 3000
Q [m³/h]
23 30 40 50 60 70 80 90 100 200 300 400 500 600 Q [l/s]
9
Product range HS
Pump configurations
10
Product range HS
Pump range
The table below gives an overview of the HS pump,
version 5 range. The table shows the complete PN 16
pump range. The PN 10 pump range does not include
all impeller sizes (see individual performance curves).
The product range includes the pumps established in
WebCAPS.
HS pumps are available with 2-, 4- or 6-pole motors;
other pole numbers are available on request.
HS pumps are available in four different construction
types, all with mechanical shaft seal.
11
Identification HS
Nominal diameter of
suction port
Nominal diameter of
discharge port
Maximum impeller diameter
(If suffix is used, “x” = different
impeller design)
12
Identification HS
The positions (1) - (4) cover four pieces of information Cooling method
2
about the mechanical shaft seal: N Uncooled stuffing box
Barrier fluid
3
E With internal barrier fluid
Example (1) (2) (3) (4)
Synthetic polymer packing rings, graphite
Grundfos type designation 4 K
impregnated. NBR O-ring in the pump
Material, rotating seal face
Material, stationary seat
Material, secondary seal and other rubber and composite parts
13
Construction HS
14
Construction HS
15
Construction HS
16
Construction HS
17
Construction HS
18
Construction HS
19
Construction HS
20
Construction HS
Impeller
The HS impeller (pos. 49) is a closed double-suction
impeller. The impeller has inflow of liquid from both
sides and is locked in position by a threaded sleeve
arrangement.
TM04 0475 0708
21
Construction HS
Coupling
As standard, HS pumps are fitted with a flexible grid
coupling.
Pos. Description
1 Shaft sleeve
2 Gland
3 Packing ring
4 Distribution ring
A Drilled hole for flushing liquid (pumped liquid)
22
Construction HS
Base frame
Pump and motor are mounted on a common base frame
designed according to Hydraulic Institute standard,
ANSI/HI 1.3-2000.
Surface treatment
Prior to delivery to the customer, pump, motor and base
frame are top coated with a black semi gloss RAL9005
coating; coating thickness is 25 μm.
Standard units are not painted internally.
Test pressure
Pressure testing is made with water at + 20 °C
containing corrosion inhibitor.
The standard hydrostatic test pressure is 1.5 times
pressure against “closed valve” or “shut off” pressure.
However, this may vary from one HS pump to another.
See table below.
23
Operating conditions HS
60
noise. However, such conditions will cause wear of
50
the carbon seal face leading to reduced seal life.
20 25 30 35 40 45 50 55 60 65 70 75 80
t [°C]
1000 2250 3500 m
NBR (xxxP)
NBR (nitrile) rubber covers a wide range of liquids at
Fig. 21 Relationship between motor output (P2) and am- temperatures below + 100 °C.
bient temperature
• Good mechanical properties.
Example
FKM (xxxV)
Fig. 21 shows that the load of the motor must be
FKM rubber covers a very wide range of liquids and
reduced to 88 % when installed 3500 m above sea
temperatures.
level.
• Poor mechanical properties at low temperatures
At an ambient temperature of 70 °C, the load of the
motor must be reduced to 78 % of the rated output. • Resistant to water up to + 90 °C
• Resistant to mineral oils and vegetable oils
Liquid temperatures • Not resistant to alkaline liquids at high
The maximum liquid temperature marked on the pump temperatures.
nameplate depends on the mechanical shaft seal used:
• Temperature range for NBR 0 °C up to + 80 °C
• Temperature range for FKM + 15 °C up to + 90 °C.
Shaft seal
The materials of the shaft seal types used in HS pumps
have certain characteristics. These characteristics may
be of importance when choosing the shaft seal for the
pump.
24
Operating conditions HS
Pressure
Maximum pressure
• Pump made of ductile iron: 16 bar
• Pump made of cast iron: 10 bar.
Flow
Minimum flow rate
The pump must not run against a closed discharge
valve as this will cause an increase in temperature/
formation of steam in the pump. This may cause shaft
damage, impeller erosion, short life of bearings, stuffing
boxes with packing rings or mechanical seals due to
stress or vibration.
The minimum flow rate must be at least 10 % of the
maximum flow rate stated on the pump nameplate.
25
Installation HS
26
Installation HS
Vibration dampers
A specific application may call for vibration dampeners Fig. 24 HS pump with accessibility for inspection and
to prevent pump vibrations from being transmitted to headroom for the use of an overhead crane
the building or the pipework. In order to select the right
vibration damper, you need this information: Foundation
We recommend that you install the pump on a concrete
• Forces transferred through the damper.
foundation which is heavy enough to provide
• Motor speed. In the case of speed control, this must permanent and rigid support for the entire pump. The
also be taken into account. foundation must be capable of absorbing any vibration,
• Desired dampening in % (recommended value: normal strain or shock. As a rule of thumb, the weight
70 %). of the concrete foundation should be 3-5 times the
The selection of vibration damper differs from weight of the complete pump unit.
installation to installation. In certain cases a wrong
In installations where silent operation is particularly
damper may increase the vibration level. Vibration
important, we recommend a foundation with a mass up
dampers should therefore be sized by the supplier of
to 5 times that of the complete pump unit.
the vibration dampers.
Grouting
Expansion joints
Expansion joints provide these advantages: NOTE: Unless otherwise specified, the base frame
• Absorption of thermal expansion and contraction of must be completely filled with grout and the
pipework caused by variations in liquid temperature. levelling wedges grouted in place. The
product warranty is void if this instruction is
• Reduction of mechanical influences in connection
with pressure surges in the pipework. not followed.
shims left in
flange on the suction side. This prevents turbulence in 19 to 32 mm place
grout
the joints, thus ensuring optimum suction conditions
Top of
and minimum pressure drop on the discharge side. Formwork
foundation
(rough)
At flow velocities > 2.4 m/s, we recommend you to fit
larger expansion joints matching the pipework. Fig. 25 Sectional view of foundation with foundation bolt,
grouting and base frame
Location Grouting compensates for uneven foundation,
Install the pump as close as possible to the supply of distributes weight of unit, dampens vibrations and
pumped liquid and with the shortest and most direct prevents shifting. Use an approved, non-shrinking
suction pipe practical. grout. If you have questions or doubts about the
grouting, please contact an expert on grouting.
27
Installation HS
28
Installation HS
Correct
towards pump
Eccentric reducer
Eccentric reducer
Fig. 29 Correctly mounted suction piping
Air pocket
TM04 0097 4907
Concentric reducer
Turbulent flow
29
Installation HS
Suction piping if the feed line comes in different Suction piping with a horizontal elbow in the feed line
horizontal planes Make sure that the liquid flow is evenly distributed to
Avoid high spots, such as loops, as they will collect air both sides of the double-suction impellers.
and throttle the system or lead to uneven pumping. There is always an uneven, turbulent flow through an
elbow, see below. If an elbow is installed in the suction
Correct pipe near the pump in a position other than vertical,
more liquid will enter one side of the impeller than the
other. This will result in heavy, unbalanced thrust loads
overheating the bearings, causing rapid wear and
reducing the hydraulic performance.
Eccentric reducer
≥ 10 X DN plus
Wrong expansion joint
DN
10 x DN
Air pocket
30
Installation HS
Discharge piping
The discharge pipe is usually preceded by a non-return
valve and a discharge isolating/throttle valve. The non-
return valve protects the pump against excessive back
pressure and reverse rotation of the pump and prevents
back flow through the pump in case of operational stop
or failure of the motor.
In order to minimise friction losses and hydraulic noise
in the pipework, flow velocities should not exceed 3 m/s
(9 ft/sec) in the discharge pipe (port).
On long horizontal runs, it is desirable to keep the
piping as level as possible.
Avoid high spots, such as loops as they will collect air
and throttle the system or lead to uneven pumping.
Auxiliary piping
1. Drains
Install drain pipes from pump casing and stuffing
boxes to a convenient disposal point.
2. Pumps fitted with stuffing boxes
When suction pressure is below ambient pressure,
supply the stuffing boxes with liquid to provide
lubrication and prevent the ingress of air. This is
normally achieved via a flushing pipe from the pump
discharge side to the stuffing box. A control valve or
orifice plate may be fitted in the flushing pipe to
control the pressure to the packing gland/stuffing
box.
If the pumped liquid is dirty and cannot be used for
flushing the seals, we recommend a separate clean,
compatible liquid supply to the stuffing box at 1 bar
(15 psi) above the suction pressure.
3. Pumps fitted with mechanical seals
Seals requiring re-circulation will normally be
provided with a flushing pipe from the pump casing.
Note: When pumping hot liquids, we recommend
that the supply of any external flushing or cooling
liquid is continued after stopping the pump. This
should be done to avoid seal damage.
31
Selection of product HS
Pump size H
Selection of pump size should be based on these data: [m]
HS 300-250-305
40 ISO 9906 Grade 2
• required flow and pressure
36
• pressure loss as a result of height differences /304.8 Duty point
(geometric lifting height) 32 + 10 %
/281.3
• friction loss in the pipework (pipes, bends, valves, 28 + 20 %
etc.) + 30 %
24 /257.8
• best efficiency at the estimated duty point.
20 /234.3
Max.flow
Efficiency 16 /210.8 rate
NPSH
margin
[m]
If you expect the pump to always operate in the same
12 12
duty point, select a pump which is operating in a duty
point corresponding to the best efficiency of the pump. 8 8
4 NPSH 4
In case of varying consumption, select a pump whose
60 /304.8 60
a) Select one of the following flow rate margins for your /281.3
40 40
pump:
TM04 0349 0608
/257.8
20 /234.3 20
/210.8
- Duty point to the end of the actual curve 0 0
(default in CAPS).
0 200 400 600 800 1000 Q [m³/h]
- Duty point + 30 %
- Duty point + 20 % Fig. 37 Establishing P2 for a selected flow rate margin of
- Duty point + 10 %. 30 %
32
Selection of product HS
In some cases, however, the input power actually To establish the motor safety margin, select method 1
decreases as the flow rate increases. It will thus be or alternatively method 2:
found at some other point within this flow range.
Method 1)
This is typically the case when the impeller is trimmed
Add a safety margin as outlined in ISO 5199 to the
to the smallest diameter.
maximum P2 found when determining parameter 1.
(Grundfos recommends the addition of a safety margin
H
[m] in accordance with this standard; default in WebCAPS.)
HS 300-250-305
40 ISO 9906 Grade 2
Required pump power up to Motor power
36 [kW] P2 [kW]
/304.8
540 600
32 473 525
/281.3
28
405 450
360 400
24 /257.8
338 375
/234.3 320 355
20
302 335
16 /210.8
NPSH 284 315
[m]
225 250
12 12
180 200
8 8 144 160
Duty point 119 132
4 NPSH 4
Max. flow rate margin
99 110
0 0 81 90
68 75
P2 0 200 400 600 800 1000 Q [m³/h] Eta
[kW] [%] 49 55
80 80 40 45
60 /304.8 60 32.5 37
/281.3
40 40 26 30
TM04 0350 0608
/257.8
20 /234.3 20 19 22
/210.8
P2 max 15.9 18.5
0 0
12.8 15
0 200 400 600 800 1000 Q [m³/h]
9.1 11
6.1 7.5
Fig. 38 Establishing the maximum P2 when P2 decreases 4.3 5.5
as the flow rate increases. 3.2 4
2.3 3
Parameter 2 - motor safety margin
1.7 2.2
As with any system, uncertainties and tolerances exist,
1.1 1.5
the motor safety margin takes the following into
Fig. 39 Safety margins according to ISO 5199
account:
Method 2)
• The actual head is at the high end of the tolerance Add a 5 % safety margin to the maximum P2 found
described in ISO 9906. This will increase the
when determining parameter 1.
required P2.
Note: If a safety margin of 5 % is selected, normal
• Pump efficiency is at the low end of the tolerance guarantees of the performance from Grundfos may not
described in ISO 9906. This will increase the
apply.
required P2.
• Motor efficiency is at the low end. If not specified by the customer, the motor size will be
determined in accordance with the WebCAPS defaults
listed above. This means a motor which covers the full
performance range and with a motor safety margin
according to ISO 5199.
33
34
Pumped liquids HS
Pumped liquids
We recommend HS pumps for thin, clean and non-
aggressive, non-explosive liquids, not containing solid
particles or fibres. The liquid must not attack the pump
materials chemically or mechanically.
The mechanical shaft seal must be suitable for the
liquid.
The maximum liquid temperature range depends on the
mechanical shaft seal used:
Nitrile rubber (xxxP): 0 °C to + 80 °C
FKM (xxxV): + 15 °C to + 90 °C.
Water in heating and ventilating systems often contains
additives to prevent negative effects such as system
corrosion or calcareous deposits. If you want to use the
pump for such liquids and if the temperature is above
80 °C, use special shaft seals to avoid crystallization/
precipitation between the seal faces.
35
Electrical data HS
2-pole motors
Motor P2 Standard voltage I 1/1
Cos ϕ 1/1 η Istart/I1/1
Frame size
[kW] [V] [A] [%] [%]
18.5 TECO 160L 380-480 D/660-690 Y 33.5-26.5/19.2-18.4 0.92-0.90 91.4-93.2 840
22 TECO 180MA 380-480 D/660-690 Y 40.0-34.0/23.0-24.0 0.90-0.83 92.6-93.5 860
30 TECO 200LA 380-480 D/660-690 Y 56.0-44.5/32.5-31.0 0.88-0.86 92.2-93.6 860
37 TECO 200LA 380-480 D/660-690 Y 67.0-52.5/38.5-36.5 0.89 93.8-95 860
45 TECO 225MA 380-480 D/660-690 Y 78.5-63.0/45.0-44.0 0.94-0.91 93.3-94.3 840
55 TECO 250SA 380-480 D/660-690 Y 95.5-76.5/55.0-53.0 0.93-0.92 94.0 740
75 TECO 250MA 380-480 D/660-690 Y 128-102/73.5-71.5 0.94-0.93 94.6 750
90 TECO 280SA 380-480 D/660-690 Y 154-124/88.0-85.5 0.94-0.93 95.0 700
110 TECO 280MA 380-480 D/660-690 Y 190-150/108-104 0.93 95.5 760
4-pole motors
Motor P2 Standard voltage I 1/1
Cos ϕ 1/1 η Istart/I1/1
Frame size
[kW] [V] [A] [%] [%]
2.2 TECO 100L 220-277 D/380-480 Y 7.80-6.30/4.50-3.65 0.85-0.83 87.2-87.9 760-960
3 TECO 100L 380-480 D/660-690 Y 6.25-5.05/3.60-3.50 0.83-0.81 87.7-88.4 980
3.7 TECO 112M 380-480 D/660-690 Y 7.45-6.00/4.30-4.15 0.85-0.83 89.2-89.9 980
4 TECO 112M 380-480 D/660-690 Y 8.05-6.45/4.60-4.50 0.85-0.83 89.2-89.9 980
5.5 TECO 132S 380-480 D/660-690 Y 10.8-8.50/6.20-5.95 0.86-0.85 90.6-91.5 980
7.5 TECO 132M 380-480 D/660-690 Y 14.4-11.6/8.35-8.10 0.87-0.85 90.7-91.5 870
11 TECO 160M 380-480 D/660-690 Y 20.6-16.4/11.6-11.4 0.89-0.87 92.7-93.5 870
15 TECO 160L 380-480 D/660-690 Y 27.0-22.0/15.6-15.2 0.90-0.88 93.2-94.0 860
18.5 TECO 180MC 380-480 D/660-690 Y 34.5-28.0/19.8-19.4 0.87-0.85 93.7-94.5 880
22 TECO 180LC 380-480 D/660-690 Y 41.0-33.0/23.6-23.0 0.87-0.85 93.7-94.5 830
30 TECO 200LC 380-480 D/660-690 Y 54.0-43.5/31.0-30.5 0.89-0.87 94.2-95.0 930
37 TECO 225SC 380-480 D/660-690 Y 68.5-55.0/39.5-38.5 0.87-0.85 94.7-95.5 780
45 TECO 225MC 380-480 D/660-690 Y 82.5-66.5/47.5-46.5 0.87-0.85 94.7-95.5 740
55 TECO 250SC 380-480 D/660-690 Y 104-80.0/60.0-55.5 0.85-0.86 94.9-96.0 740
75 TECO 250MC 380-480 D/660-690 Y 142-110/81.5-76.0 0.85-0.86 94.7-96.0 730
90 TECO 280SC 380-480 D/660-690 Y 170-130/97.5-91.0 0.85-0.86 95.0-96.0 700
110 TECO 280MB 380-480 D/660-690 Y 206-160/120-112 0.85-0.86 95.5-96.0 680
132 TECO 315SB 380-480 D/660-690 Y 250-190/142-132 0.85-0.87 95.1-96.0 600
160 TECO 315MB 380-480 D/660-690 Y 300-230/172-160 0.86-0.87 95.1-96.0 600
200 TECO 315MB 380-480 D/660-690 Y 365-290/210-166 0.88 95.8 780
250 TECO 315CB 380-480 D/660-690 Y 455-355/260-246 0.89 94.5-95.2 550-830
315 TECO 315DB 380-480 D/660-690 Y 575-445/330-310 0.88-0.90 94.5-95.2 550-830
335 TECO 315DB 380-480 D/660-690 Y 610-470/350-330 0.88-0.90 94.5-95.3 550-830
355 TECO 315DB 380-480 D/660-690 Y 645-510/370-355 0.89-0.88 94.5-95.2 550-830
375 TECO 355AB 380-480 D/660-690 Y 680-540/390-375 0.89-0.88 94.5-95.3 550-830
400 TECO 355CB 380-480 D/660-690 Y 730-570/420-395 0.88-0.89 94.7-95.3 550-830
450 TECO 355CB 380-480 D/660-690 Y 820-640/470-445 0.88-0.89 94.7-95.5 550-830
500 TECO 400AB 380-480 D/660-690 Y 890-700/515-485 0.90 94.7-95.5 550-830
525 TECO 400AB 380-480 D/660-690 Y 935-735/540-510 0.90 94.7-95.6 550-830
560 TECO 400CB 380-480 D/660-690 Y 995-785/575-545 0.90 94.8-95.6 550-830
600 TECO 400CB 380-480 D/660-690 Y 1060-840/615-585 0.90 94.8-95.7 550-830
36
Electrical data HS
6-pole motors
Motor P2 Standard voltage I 1/1
Cos ϕ 1/1 η Istart/I1/1
Frame size
[kW] [V] [A] [%] [%]
15.0 TECO 180LC 380-480 D/660-690 Y 29.5-24.0/17.0-16.8 0.85-0.81 91.6-93.1 520-830
18.5 TECO 200LC 380-480 D/660-690 Y 37.0-30.5/21.6-21.0 0.82-0.78 92.2-93.5 460-760
22.0 TECO 200LC 380-480 D/660-690 Y 43.5-35.5/25.0-24.5 0.83-0.80 92.3-93.8 460-770
30 TECO 225MC 380-480 D/660-690 Y 56.0-46.5/32.5-32.0 0.87-0.83 93.5-94.2 460-730
37 TECO 250SC 380-480 D/660-690 Y 68.0-56.5/39.0-39.5 0.88-0.83 94.0-94.8 540-870
45 TECO 250MC 380-480 D/660-690 Y 82.5-67.5/47.5-47.0 0.88-0.84 94.1-94.9 540-880
55 TECO 280SB 380-480 D/660-690 Y 99.5-78.5/57.0-54.5 0.89 95.0 530-830
75 TECO 280MB 380-480 D/660-690 Y 136-108/78.0-74.5 0.89 95.0 600-850
90 TECO 315SB 380-480 D/660-690 Y 160-126/92.5-88.5 0.90 95.2 600-830
110 TECO 315MB 380-480 D/660-690 Y 196-156/114-108 0.89 95.2 510-820
132 TECO 315MB 380-480 D/660-690 Y 236-184/134-128 0.90 95.2 550-800
160 TECO 315AB 380-480 D/660-690 Y 300-232/174-166 0.86-0.87 94.5-95.5 520-800
200 TECO 315AB 380-480 D/660-690 Y 375-290/216-208 0.86-0.87 94.5-95.6 520-800
300 TECO 355AB 380-480 D/660-690 Y 565-430/325-310 0.86-0.87 94.5-96.0 550-840
315 TECO 355CB 380-480 D/660-690 Y 580-455/335-320 0.87 95.0-96.0 550-840
335 TECO 355CB 380-480 D/660-690 Y 620-480/355-340 0.87 95.0-96.0 550-840
355 TECO 400AB 380-480 D/660-690 Y 650-505/375-355 0.88 95.0-96.0 540-830
375 TECO 400AB 380-480 D/660-690 Y 685-535/395-375 0.88 95.0-96.0 540-830
450 TECO 400AB 380-480 D/660-690 Y 820-640/470-450 0.88 95.4-96.2 540-830
37
Curve charts and technical data HS
H
[m]
HS 65-50-242
Total pump head 130
H = Htotal /241.3 60 Hz, n = 3550 min-1
ISO 9906 Grade 2 Pump type and speed
120
110 /223.8
100
QH curve for the
/206.3 individual pump.
90 The bold curve indicates
the recommended
80 /188.9
performance range.
70
/171.5
60 NPSH
[m]
50 25
40 20
30 15
The NPSH curve is an
20 10 average curve for all
variants shown. When
NPSH sizing the pumps, add a
10 5
safety margin of at least
0.5 m.
0 0
0 10 20 30 40 50 60 70 80 90 100 110 120 130 Q [m³/h]
P2 Eta
[kW] [%]
70 70
The eta curves show
the efficiency of the
60 /241.3 60 pumps shown
/223.8
/206.3 /241.3
50 /188.9 50
/171.5
/223.8
40 40
/206.3
30 30
/188.9
20 20 The power curves
/171.5
indicate pump input
TM03 9844 4507
10 10
power [P2] for the
pumps shown
0 0
0 10 20 30 40 50 60 70 80 90 100 110 120 130 Q [m³/h]
38
Curve charts and technical data HS
39
Performance curves HS 65-50-242
2-pole
Technical data
2-pole
H
[m]
HS 65-50-242
130
/241.3 60 Hz, n = 3550 min-1
ISO 9906 Grade 2
120
110 /223.8
100
/206.3
90
80 /188.9
70
/171.5
60 NPSH
[m]
50 25
40 20
30 15
20 10
NPSH
10 5
0 0
0 10 20 30 40 50 60 70 80 90 100 110 120 130 Q [m³/h]
P2 Eta
[kW] [%]
70 70
60 /241.3 60
/223.8
/206.3 /241.3
50 /188.9 50
/171.5
/223.8
40 40
/206.3
30 30
/188.9
20 20
/171.5
10 10
TM03 9844 4507
0 0
0 10 20 30 40 50 60 70 80 90 100 110 120 130 Q [m³/h]
40
Performance curves HS 65-50-242
2-pole
Dimensional sketches
HS standard, 65-50-242
41
Technical data HS 100-80-242
2-pole
H
[m]
/241.3 HS 100-80-242
130
60 Hz, n = 3560 min-1
ISO 9906 Grade 2
120
/222.3
110
100
/203.2
90
80
/184.2
70
60 /165.1
50
40 NPSH
[m]
30 16
20 12
10 8
NPSH
0 4
0 20 40 60 80 100 120 140 160 180 200 220 240 Q [m³/h]
P2 Eta
[kW] [%]
160 80
140 70
120 /241.3 60
/203.2 /222.3
100 /184.2 50
/241.3
/165.1
80 40
/222.3
60 30
/203.2
40 /184.2 20
/165.1
20 10
TM03 9847 450
0 0
0 20 40 60 80 100 120 140 160 180 200 220 240 Q [m³/h]
The grey line represents a maximum shaft load of 1.27 kW/100 rpm for a Ø25.4 (1 inch) pump shaft when pumping
water at the conditions mentioned on page 39. If the required shaft load exceeds 1.27 kW/100 rpm, use a pump with a
Ø30.2 (1.19 inch) pump shaft.
Be aware that the curves will change when pumping liquids with a higher density and/or viscosity than water.
42
Performance curves HS 100-80-242
2-pole
Dimensional sketch
HS standard, 100-80-242
43
Technical data HS 125-100-280
2-pole
H
[m]
160 /279.4 HS 125-100-280
60 Hz, n = 3570 min-1
150 ISO 9906 Grade 2
140
130 /250.7
120
110
100 /222.0
90
80
/193.6
70
60
50 NPSH
/165.1 [m]
40 40
30 30
20 20
10 10
NPSH
0 0
0 40 80 120 160 200 240 280 320 360 Q [m³/h]
P2 Eta
[kW] [%]
320 80
280 /279.4 70
/250.7
240 /222.0 60
/193.6
200 50
160 /165.1 40
/279.4
120 30
/250.7
80 20
/222.0
40 /193.6 10
TM03 9850 4507
/165.1
0 0
0 40 80 120 160 200 240 280 320 360 Q [m³/h]
The grey line represents a maximum shaft load of 2.7 kW/100 rpm when pumping water at the conditions mentioned on
page 39. If the required shaft load exceeds 2.7 kW/100 rpm, use a larger pump.
Be aware that the curves will change when pumping liquids with a higher density and/or viscosity than water.
44
Performance curves HS 125-100-280
2-pole
Dimensional sketch
HS standard, 125-100-280
45
Technical data HS 125-100-305
2-pole
H
[m]
HS 125-100-305
/304.8
200 60 Hz, n = 3560 min-1
ISO 9906 Grade 2
180
/273.1
160
140
/241.3
120
100 /209.6
80
NPSH
/177.8
[m]
60 30
40 20
20 NPSH 10
0 0
0 50 100 150 200 250 300 350 400 450 500 550 Q [m³/h]
P2 Eta
[kW] [%]
400 80
/304.8
350 70
/273.1
/241.3
300 60
/209.6 /304.8
/177.8
250 50
200 /273.1 40
150 30
/241.3
100 20
/209.6
50 /177.8 10
TM03 9852 450
0 0
0 50 100 150 200 250 300 350 400 450 500 550 Q [m³/h]
The grey line represents a maximum shaft load of 2.7 kW/100 rpm when pumping water at the conditions mentioned on
page 39. If the required shaft load exceeds 2.7 kW/100 rpm, use a larger pump.
Be aware that the curves will change when pumping liquids with a higher density and/or viscosity than water.
46
Performance curves HS 125-100-305
2-pole
Dimensional sketch
HS standard, 125-100-305
47
Technical data HS 65-50-242
4-pole
4-pole
H
[m]
32 HS 65-50-242
/241.3 60 Hz, n = 1750 min-1
30 ISO 9906 Grade 2
28
/223.8
26
24
/206.3
22
20
/188.9
18
16 /171.5
14
12
10
8 NPSH
[m]
6 12
4 8
NPSH
2 4
0 0
0 5 10 15 20 25 30 35 40 45 50 55 60 65 Q [m³/h]
P2 Eta
[kW] [%]
14 70
12 /241.3 60
/223.8
10 /206.3 50
/171.5 /188.9
8 40
/241.3
6 30
/223.8
4 /206.3 20
/188.9
2 /171.5 10
TM03 9843 4507
0 0
0 5 10 15 20 25 30 35 40 45 50 55 60 65 Q [m³/h]
48
Performance curves HS 65-50-242
4-pole
Dimensional sketch
HS standard, 65-50-242
49
Technical data HS 65-50-331
4-pole
H
[m]
56
/330.2 HS 65-50-331
60 Hz, n = 1770 min-1
52 ISO 9906 Grade 2
/304.7
48
44
/279.4
40
36 /254.0
32
/228.6
28
24
20 NPSH
[m]
16 8
12 6
8 4
NPSH
4 2
0 0
0 10 20 30 40 50 60 70 80 90Q [m³/h]
P2 Eta
[kW] [%]
30 60
25 /330.2 50
/304.7
/279.4
20 /254.0 40
/228.6
/330.2
15 30
/304.7
/279.4
10 20
/254.0
/228.6
5 10
TM03 9845 4507
0 0
0 10 20 30 40 50 60 70 80 90Q [m³/h]
50
Performance curves HS 65-50-331
4-pole
Dimensional sketch
HS standard, 65-50-331
51
Technical data HS 100-80-242
4-pole
H
[m]
34 HS 100-80-242
/241.3 60 Hz, n = 1770 min-1
32
ISO 9906 Grade 2
30
28 /222.3
26
24
/203.2
22
20
/184.2
18
16
/165.1
14
12
10 NPSH
[m]
8 10
6 8
4 NPSH 6
2 4
0 2
0 10 20 30 40 50 60 70 80 90 100 110 120 Q [m³/h]
P2 Eta
[kW] [%]
16 80
14 70
/241.3
12 60
/203.2 /222.3 /241.3
10 /184.2 50
/165.1
/222.3
8 40
6 /203.2 30
/184.2
4 20
/165.1
2 10
TM03 9846 4507
0 0
0 10 20 30 40 50 60 70 80 90 100 110 120 Q [m³/h]
52
Performance curves HS 100-80-242
4-pole
Dimensional sketch
HS standard, 100-80-242
53
Technical data HS 100-80-356
4-pole
H
[m]
/355.6
HS 100-80-356
65
60 Hz, n = 1780 min-1
ISO 9906 Grade 2
60
/329.6
55
50
/303.5
45
40 /277.5
35
/251.5
30
25 NPSH
[m]
20 16
15 12
10 8
5 NPSH 4
0 0
0 20 40 60 80 100 120 140 160 180 Q [m³/h]
P2 Eta
[kW] [%]
60 70
/303.5 /355.6
/277.5 /329.6
50 /251.5 60
40 50
/355.6
30 /329.6 40
/303.5
20 30
/277.5
10 /251.5 20
TM03 9848 4507
0 10
0 20 40 60 80 100 120 140 160 180 Q [m³/h]
54
Performance curves HS 100-80-356
4-pole
Dimensional sketch
HS standard, 100-80-356
55
Technical data HS 125-100-280
4-pole
H
[m]
40 /279.4 HS 125-100-280
38 60 Hz, n = 1770 min-1
ISO 9906 Grade 2
36
34
32 /250.7
30
28
26
24 /222.0
22
20
18 /193.6
16
14
12
/165.1 NPSH
10
[m]
8 16
6 12
4 8
NPSH
2 4
0 0
0 20 40 60 80 100 120 140 160 180 Q [m³/h]
P2 Eta
[kW] [%]
32 80
28 /279.4 70
/250.7
24 /222.0 60
/193.6
20 50
/165.1 /279.4
16 40
12 /250.7 30
8 /222.0 20
4 /193.6 10
/165.1
TM03 9849 4507
0 0
0 20 40 60 80 100 120 140 160 180 Q [m³/h]
56
Performance curves HS 125-100-280
4-pole
Dimensional sketch
HS standard, 125-100-280
57
Technical data HS 125-100-305
4-pole
H
[m]
HS 125-100-305
52
/304.8 60 Hz, n = 1780 min-1
ISO 9906 Grade 2
48
44
/273.1
40
36
32 /241.3
28
/209.6
24
20
/177.8
16
12 NPSH
[m]
8 8
4 4
NPSH
0 0
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 Q [m³/h]
P2 Eta
[kW] [%]
40 80
/304.8
35 /273.1 70
/241.3 /304.8
30 /209.6 60
/177.8
25 50
/273.1
20 40
15 /241.3 30
10 /209.6 20
5 /177.8 10
TM03 9851 4507
0 0
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 Q [m³/h]
58
Performance curves HS 125-100-305
4-pole
Dimensional sketch
HS standard, 125-100-305
59
Technical data HS 125-100-381
4-pole
H
[m]
75
/381.0 HS 125-100-381
60 Hz, n = 1780 min-1
70 ISO 9906 Grade 2
65
/346.0
60
55
50 /311.0
45
40 /276.2
35
30 /241.3
25 NPSH
[m]
20 20
15 15
10 10
5 NPSH 5
0 0
0 40 80 120 160 200 240 280 320 360 400 Q [m³/h]
P2 Eta
[kW] [%]
160 80
140 70
120 /381.0 60
/346.0
/311.0
100 /276.2 50
/381.0
/241.3
80 40
/346.0
60 30
/311.0
40 20
/276.2
20 /241.3 10
TM03 9853 4507
0 0
0 40 80 120 160 200 240 280 320 360 400 Q [m³/h]
60
Performance curves HS 125-100-381
4-pole
Dimensional sketch
HS standard, 125-100-381
61
Technical data HS 150-125-305
4-pole
H
[m]
/304.8
HS 150-125-305
48
60 Hz, n = 1780 min-1
ISO 9906 Grade 2
44
40
/273.1
36
32
/241.3
28
24
/209.6
20
16 /177.8
12
NPSH
[m]
8 8
4 4
NPSH
0 0
0 40 80 120 160 200 240 280 320 360 400 Q [m³/h]
P2 Eta
[kW] [%]
80 80
/304.8
/273.1
70 70
/241.3
60 /209.6 60
50 /304.8 50
/177.8
40 40
/273.1
30 30
20 /241.3 20
/209.6
10 10
/177.8
TM03 9854 4507
0 0
0 40 80 120 160 200 240 280 320 360 400 Q [m³/h]
62
Performance curves HS 150-125-305
4-pole
Dimensional sketch
HS standard, 150-125-305
63
Technical data HS 150-125-381
4-pole
H
[m]
80 /381.0
HS 150-125-381
60 Hz, n = 1780 min-1
75 ISO 9906 Grade 2
70
/342.9
65
60
55
/304.8
50
45
40 /266.7
35
30
/228.6
25 NPSH
[m]
20 20
15 15
10 10
5 NPSH 5
0 0
0 40 80 120 160 200 240 280 320 360 400 440 480 520 Q [m³/h]
P2 Eta
[kW] [%]
160 80
/381.0
/342.9
140 /304.8 70
120 /266.7 60
/381.0
100 /228.6 50
80 /342.9 40
60 30
/304.8
40 20
/266.7
20 /228.6 10
TM03 9855 4507
0 0
0 40 80 120 160 200 240 280 320 360 400 440 480 520 Q [m³/h]
64
Performance curves HS 150-125-381
4-pole
Dimensional sketch
HS standard, 150-125-381
65
Technical data HS 200-150-305A
4-pole
H
[m]
HS 200-150-305A
48 /304.8
60 Hz, n = 1780 min-1
ISO 9906 Grade 2
44
40
/276.4
36
32
/248.0
28
24 /219.9
20
/190.5
16
NPSH
[m]
12 12
8 8
4 4
NPSH
0 0
0 40 80 120 160 200 240 280 320 360 400 440 480 Q [m³/h]
P2 Eta
[kW] [%]
80 80
70 70
/304.8
/248.0 /276.4
60 60
/219.9
50 /190.5 /304.8 50
40 40
/276.4
30 30
/248.0
20 20
/219.9
10 10
/190.5
TM03 9856 4507
0 0
0 40 80 120 160 200 240 280 320 360 400 440 480 Q [m³/h]
66
Performance curves HS 200-150-305A
4-pole
Dimensional sketch
HS standard, 200-150-305A
67
Technical data HS 200-150-305C
4-pole
H
[m]
HS 200-150-305C
52
/304.8 60 Hz, n = 1780 min-1
ISO 9906 Grade 2
48
44
/273.1
40
36
32 /241.3
28
24 /209.6
20
/177.8
16 NPSH
[m]
12 12
8 8
4 4
NPSH
0 0
0 50 100 150 200 250 300 350 400 450 500 550 600 650 700 Q [m³/h]
P2 Eta
[kW] [%]
140 80
120 70
/241.3 /273.1 /304.8
100 60
/209.6
80 /177.8 50
/304.8
60 40
/273.1
40 30
/241.3
20 /209.6 20
/177.8
TM03 9857 450
0 10
0 50 100 150 200 250 300 350 400 450 500 550 600 650 700 Q [m³/h]
68
Performance curves HS 200-150-305C
4-pole
Dimensional sketch
HS standard, 200-150-305C
69
Technical data HS 200-150-381
4-pole
H
[m]
80 /381.0
HS 200-150-381
60 Hz, n = 1780 min-1
75 ISO 9906 Grade 2
70
65 /342.9
60
55
/304.8
50
45
40 /266.7
35
30
/228.6
25 NPSH
[m]
20 16
15 12
10 8
5 NPSH 4
0 0
0 50 100 150 200 250 300 350 400 450 500 550 600 650 700 750 800 Q [m³/h]
P2 Eta
[kW] [%]
280 80
200 60
/266.7
160 /228.6 50
/381.0
120 40
/342.9
80 30
/304.8
40 /266.7 20
/228.6
TM03 9858 4507
0 10
0 50 100 150 200 250 300 350 400 450 500 550 600 650 700 750 800 Q [m³/h]
70
Performance curves HS 200-150-381
4-pole
Dimensional sketch
HS standard, 200-150-381
71
Technical data HS 200-150-483
4-pole
H
[m]
HS 200-150-483
130
/482.6 60 Hz, n = 1780 min-1
ISO 9906 Grade 2
120
/457.2
110
/431.8
100
90 /406.4
80
/381.0
70
60
50 NPSH
[m]
40 20
30 15
20 10
10 5
NPSH
0 0
0 50 100 150 200 250 300 350 400 450 500 550 600 650 Q [m³/h]
P2 Eta
[kW] [%]
400 80
350 70
/482.6
300 /431.8 /457.2 60
/381.0 /406.4
250 50
/482.6
200 40
/457.2
150 30
/431.8
/406.4
100 20
/381.0
50 10
TM03 9859 4507
0 0
0 50 100 150 200 250 300 350 400 450 500 550 600 650 Q [m³/h]
The grey line represents a maximum shaft load of 7.25 kW/100 rpm for a Ø44.5 (1.75 inch) pump shaft when pumping
water at the conditions mentioned on page 39. If the required shaft load exceeds 7.25 kW/100 rpm, use a pump with a
Ø50.8 (2 inch) pump shaft.
Be aware that the curves will change when pumping liquids with a higher density and/or viscosity than water.
72
Performance curves HS 200-150-483
4-pole
Dimensional sketch
HS standard, 200-150-483
73
Technical data HS 200-150-508
4-pole
H
[m]
150
HS 200-150-508
/508.0
60 Hz, n = 1780 min-1
140 ISO 9906 Grade 2
130
/444.5
120
110
/381.0
100
90 /368.3
80
/355.6
70
60
50 NPSH
[m]
40 16
30 12
NPSH
20 8
10 4
0 0
0 100 200 300 400 500 600 700 800 Q [m³/h]
P2 Eta
[kW] [%]
800 80
700 70
/508.0
/381.0 /444.5
600 /368.3 60
/355.6
500 50
400 40
/508.0
300 /444.5 30
/381.0
200 20
/368.3
/355.6
100 10
TM03 9861 450
0 0
0 100 200 300 400 500 600 700 800 Q [m³/h]
74
Performance curves HS 200-150-508
4-pole
Dimensional sketch
HS standard, 200-150-508
75
Technical data HS 250-200-305
4-pole
H
[m]
/304.8 HS 250-200-305
48
60 Hz, n = 1780 min-1
ISO 9906 Grade 2
44
40 /273.7
36
32
/242.6
28
24 /211.5
20
/180.3
16
NPSH
[m]
12 12
8 8
4 NPSH 4
0 0
0 100 200 300 400 500 600 700 800 900 Q [m³/h]
P2 Eta
[kW] [%]
160 80
140 70
/304.8
120 60
/242.6 /273.7
100 /211.5 50
80 /180.3 /304.8 40
60 /273.7 30
40 20
/242.6
/211.5
20 10
/180.3
TM03 9863 4507
0 0
0 100 200 300 400 500 600 700 800 900 Q [m³/h]
76
Performance curves HS 250-200-305
4-pole
Dimensional sketch
HS standard, 250-200-305
77
Technical data HS 250-200-381
4-pole
H
[m]
80 HS 250-200-381
/381.0 60 Hz, n = 1780 min-1
75 ISO 9906 Grade 2
70
65
/342.9
60
55
50 /304.8
45
40 /266.7
35
30 /228.6
25 NPSH
[m]
20 16
15 12
10 8
5 NPSH 4
0 0
0 100 200 300 400 500 600 700 800 900 1000 1100 Q [m³/h]
P2 Eta
[kW] [%]
400 80
/381.0
350 /342.9 70
/304.8
300 /266.7 60
250 /228.6 50
200 /381.0 40
150 /342.9 30
100 20
/304.8
50 /266.7 10
/228.6
TM03 9864 4507
0 0
0 100 200 300 400 500 600 700 800 900 1000 1100 Q [m³/h]
78
Performance curves HS 250-200-381
4-pole
Dimensional sketch
HS standard, 250-200-381
79
Technical data HS 300-200-489
4-pole
H
[m]
/489.0 HS 300-200-489
130
60 Hz, n = 1780 min-1
ISO 9906 Grade 2
120
/455.7
110
100
/422.4
90
/389.0
80
70
/355.6
60
50
40 NPSH
[m]
30 30
20 20
10 10
NPSH
0 0
0 200 400 600 800 1000 1200 1400 1600 1800 Q [m³/h]
P2 Eta
[kW] [%]
800 80
700 70
/489.0
/422.4 /455.7
600 /389.0 60
/355.6
/489.0
500 50
/455.7
400 40
/422.4
300 30
/389.0
200 20
/355.6
100 10
TM03 9866 4507
0 0
0 200 400 600 800 1000 1200 1400 1600 1800 Q [m³/h]
80
Performance curves HS 300-200-489
4-pole
81
Technical data HS 300-250-305
4-pole
H
[m]
HS 300-250-305
52
60 Hz, n = 1780 min-1
/304.8 ISO 9906 Grade 2
48
44
/281.3
40
36
/257.8
32
/234.3
28
24
/210.8
20
16 NPSH
[m]
12 15
8 10
NPSH
4 5
0 0
0 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300 1400 1500 Q [m³/h]
P2 Eta
[kW] [%]
180 80
160 70
/304.8
140 /281.3 60
/257.8
/234.3
120 /210.8 /304.8 50
100 40
/281.3
80 30
60 /257.8 20
40 /234.3 10
TM03 9868 4507
/210.8
20 0
0 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300 1400 1500 Q [m³/h]
82
Performance curves HS 300-250-305
4-pole
Dimensional sketch
HS standard, 300-250-305
83
Technical data HS 300-250-381
4-pole
H
[m]
80 HS 300-250-381
/381.0 60 Hz, n = 1780 min-1
75 ISO 9906 Grade 2
70
/355.5
65
60
55 330.0
50
/304.7
45
/279.4
40
35
30
25 NPSH
[m]
20 16
15 12
10 8
NPSH
5 4
0 0
0 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300 1400 1500 1600 Q [m³/h]
P2 Eta
[kW] [%]
450 90
400 80
/381.0
350 /355.5 70
/330.0
300 /304.7 60
/279.4 /381.0
250 50
200 /355.5 40
150 /330.0 30
100 /304.7 20
/279.4
50 10
TM03 9870 4507
0 0
0 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300 1400 1500 1600 Q [m³/h]
84
Performance curves HS 300-250-381
4-pole
Dimensional sketch
HS standard, 300-250-381
85
Technical data HS 350-250-498
4-pole
H
[m]
140
HS 350-250-498
/497.8 60 Hz, n = 1780 min-1
130 ISO 9906 Grade 2
120
/462.3
110
100 /426.7
90
/391.2
80
70
/355.6
60
50 NPSH
[m]
40 40
30 30
20 20
10 10
NPSH
0 0
0 200 400 600 800 1000 1200 1400 1600 1800 2000 2200 2400 2600 Q [m³/h]
P2 Eta
[kW] [%]
1600 90
1400 80
1200 /497.8 70
/426.7 /462.3
1000 /391.2 60
/355.6
800 50
/497.8
600 /462.3 40
/426.7
400 30
/391.2
200 /355.6 20
TM03 9872 4507
0 10
0 200 400 600 800 1000 1200 1400 1600 1800 2000 2200 2400 2600 Q [m³/h]
86
Performance curves HS 350-250-498
4-pole
Dimensional sketch
HS extended, 350-250-498
87
Technical data HS 350-250-630
4-pole
H
[m]
/629.9
220 HS 350-250-630
210 60 Hz, n = 1780 min-1
200 ISO 9906 Grade 2
190 /580.4
180
170
160
/530.9
150
140
130
/481.3
120
110
100 /431.8
90
80
70
60
NPSH
50 [m]
40 20
30 15
20 10
NPSH
10 5
0 0
0 200 400 600 800 1000 1200 1400 1600 1800 2000 2200 2400 2600 2800 Q [m³/h]
P2 Eta
[kW] [%]
3600 90
3200 80
2800 70
/629.9
2400 /580.4 60
/530.9
2000 /481.3 50
/431.8
1600 /629.9 40
1200 30
/580.4
800 /530.9 20
/481.3
400 /431.8 10
TM03 9874 4507
0 0
0 200 400 600 800 1000 1200 1400 1600 1800 2000 2200 2400 2600 2800 Q [m³/h]
88
Performance curves HS 350-250-630
4-pole
Dimensional sketch
HS extended, 350-250-630
89
Technical data HS 400-350-397
4-pole
H
[m]
80 /396.2
HS 400-350-397
60 Hz, n = 1780 min-1
75 ISO 9906 Grade 2
/373.4
70
65
/350.5
60
/327.7
55
50
/304.8
45
40
35
30 NPSH
[m]
25 25
20 20
15 15
10 10
NPSH
5 5
0 0
0 200 400 600 800 1000 1200 1400 1600 1800 2000 2200 2400 2600 Q [m³/h]
P2 Eta
[kW] [%]
550 90
500 80
/396.2
450 /350.5 /373.4 70
/327.7
400 /304.8 60
350 50
/396.2
300 40
/373.4
250 30
/350.5
200 20
/327.7
150 10
/304.8
TM03 9877 4507
100 0
0 200 400 600 800 1000 1200 1400 1600 1800 2000 2200 2400 2600 Q [m³/h]
90
Performance curves HS 400-350-397
4-pole
Dimensional sketch
HS extended, 400-350-397
91
Technical data HS 200-150-483
6-pole
H
[m]
HS 200-150-483
60
60 Hz, n = 1180 min-1
/482.6 ISO 9906 Grade 2
55
/457.2
50
45 /431.8
40 /406.4
35 /381.0
30
25
20
NPSH
[m]
15 12
10 8
5 4
NPSH
0 0
0 40 80 120 160 200 240 280 320 360 400 440 Q [m³/h]
P2 Eta
[kW] [%]
160 80
140 70
/482.6
120 /431.8 /457.2 60
/381.0 /406.4
100 50
80 40
60 /482.6 30
/457.2
40 /431.8 20
/406.4
/381.0
20 10
TM03 9860 4507
0 0
0 40 80 120 160 200 240 280 320 360 400 440 Q [m³/h]
92
Performance curves HS 200-150-483
6-pole
Dimensional sketch
HS extended, 200-150-483
93
Technical data HS 200-150-508
6-pole
H
[m]
HS 200-150-508
65 /508.0
60 Hz, n = 1180 min-1
ISO 9906 Grade 2
60
/444.5
55
50
/381.0
45
40 /368.3
35
/355.6
30
25
20
15 NPSH
[m]
10 8
NPSH
5 4
0 0
0 50 100 150 200 250 300 350 400 450 500 550 600 Q [m³/h]
P2 Eta
[kW] [%]
160 80
140 70
/508.0
/381.0 /444.5
120 /368.3 60
/355.6
/508.0
100 50
/444.5
80 40
/381.0
60 30
/368.3
40 20
/355.6
20 10
TM03 9862 4507
0 0
0 50 100 150 200 250 300 350 400 450 500 550 600 Q [m³/h]
94
Performance curves HS 200-150-508
6-pole
Dimensional sketch
HS extended, 200-150-508
95
Technical data HS 250-200-381
6-pole
H
[m]
34 /381.0 HS 250-200-381
60 Hz, n = 1180 min-1
32
ISO 9906 Grade 2
30
28 /342.9
26
24
22 /304.8
20
18
/266.7
16
14
/228.6
12
10 NPSH
[m]
8 8
6 6
4 4
2 NPSH 2
0 0
0 50 100 150 200 250 300 350 400 450 500 550 600 650 700 750 Q [m³/h]
P2 Eta
[kW] [%]
80 80
/381.0
70 /342.9 70
/304.8
/381.0
60 /266.7 60
/228.6
50 50
40 /342.9 40
30 30
/304.8
20 20
/266.7
10 /228.6 10
TM03 9865 4507
0 0
0 50 100 150 200 250 300 350 400 450 500 550 600 650 700 750 Q [m³/h]
96
Performance curves HS 250-200-381
6-pole
Dimensional sketch
HS extended, 250-200-381
97
Technical data HS 300-200-489
6-pole
H
[m]
HS 300-200-489
60
60 Hz, n = 1180 min-1
/489.0
ISO 9906 Grade 2
55
50 /455.7
45
/422.4
40
/389.0
35
30 /355.6
25
20
NPSH
[m]
15 15
10 10
5 5
NPSH
0 0
0 100 200 300 400 500 600 700 800 900 1000 1100 1200 Q [m³/h]
P2 Eta
[kW] [%]
400 90
350 80
300 70
/489.0
/422.4 /455.7
250 /389.0 60
/355.6
200 50
150 /489.0 40
/455.7
100 /422.4 30
/389.0
50 /355.6 20
TM03 9867 4507
0 10
0 100 200 300 400 500 600 700 800 900 1000 1100 1200 Q [m³/h]
98
Performance curves HS 300-200-489
6-pole
Dimensional sketch
HS extended, 300-200-489
99
Technical data HS 300-250-305
6-pole
H
[m]
HS 300-250-305
22 /304.8 60 Hz, n = 1180 min-1
ISO 9906 Grade 2
20
/281.3
18
16
/257.8
14
/234.3
12
10 /210.8
6
NPSH
[m]
4 8
2 4
NPSH
0 0
0 100 200 300 400 500 600 700 800 900 Q [m³/h]
P2 Eta
[kW] [%]
90 90
80 80
70 70
/304.8
60 /281.3 60
/257.8
50 /234.3 50
/210.8
40 40
/304.8
30 30
/281.3
20 20
/257.8
10 /234.3 10
/210.8
TM03 9869 4507
0 0
0 100 200 300 400 500 600 700 800 900 Q [m³/h]
100
Performance curves HS 300-250-305
6-pole
Dimensional sketch
HS extended, 300-250-305
101
Technical data HS 300-250-381
6-pole
H
[m]
34 /381.0
HS 300-250-381
60 Hz, n = 1180 min-1
32
ISO 9906 Grade 2
30
/355.5
28
26
/330.0
24
22
/304.7
20
18 /279.4
16
14
12
10 NPSH
[m]
8 8
6 6
4 4
NPSH
2 2
0 0
0 100 200 300 400 500 600 700 800 900 1000 Q [m³/h]
P2 Eta
[kW] [%]
180 90
160 80
/381.0
140 /355.5 70
/330.0
120 /304.7 60
100 /279.4 50
80 /381.0 40
60 /355.5 30
40 /330.0 20
/304.7
20 /279.4 10
TM03 9871 4507
0 0
0 100 200 300 400 500 600 700 800 900 1000 Q [m³/h]
102
Performance curves HS 300-250-381
6-pole
Dimensional sketch
HS extended, 300-250-381
103
Technical data HS 350-250-498
6-pole
H
[m]
HS 350-250-498
60
/497.8 60 Hz, n = 1180 min-1
ISO 9906 Grade 2
55
/462.3
50
45
/426.7
40
/391.2
35
30 /355.6
25
20
NPSH
[m]
15 15
10 10
5 5
NPSH
0 0
0 200 400 600 800 1000 1200 1400 1600 Q [m³/h]
P2 Eta
[kW] [%]
400 90
350 80
300 /497.8 70
/426.7 /462.3
250 /391.2 60
/355.6 /497.8
200 50
/462.3
150 40
/426.7
100 /391.2 30
/355.6
50 20
TM03 9873 4507
0 10
0 200 400 600 800 1000 1200 1400 1600 Q [m³/h]
104
Performance curves HS 350-250-498
6-pole
Dimensional sketch
HS extended, 350-250-498
105
Technical data HS 350-250-630
6-pole
H
[m]
100 /629.9 HS 350-250-630
95 60 Hz, n = 1190 min-1
ISO 9906 Grade 2
90
85 /580.4
80
75
70 /530.9
65
60
/481.3
55
50
45 /431.8
40
35
30
NPSH
25
[m]
20 8
15 6
10 4
NPSH
5 2
0 0
0 200 400 600 800 1000 1200 1400 1600 1800 Q [m³/h]
P2 Eta
[kW] [%]
900 90
800 80
700 70
/629.9
600 /580.4 60
/530.9
500 /481.3 50
/431.8 /629.9
400 40
300 /580.4 30
/530.9
200 20
/481.3
100 /431.8 10
TM03 9875 4507
0 0
0 200 400 600 800 1000 1200 1400 1600 1800 Q [m³/h]
106
Performance curves HS 350-250-630
6-pole
Dimensional sketch
HS extended, 350-250-630
107
Technical data HS 350-300-508
6-pole
H
[m]
60 /508.0
HS 350-300-508
60 Hz, n = 1190 min-1
56 ISO 9906 Grade 2
52
/463.6
48
44
/419.1
40
36
/374.7
32
28
/330.2
24
20 NPSH
[m]
16 16
12 12
8 8
NPSH
4 4
0 0
0 200 400 600 800 1000 1200 1400 1600 1800 2000 2200 2400 2600 Q [m³/h]
P2 Eta
[kW] [%]
450 90
400 80
350 /508.0 70
/463.6
/508.0
300 60
/419.1
250 /374.7 50
/463.6
200 40
/330.2
150 /419.1 30
100 /374.7 20
/330.2
50 10
TM03 9876 4507
0 0
0 200 400 600 800 1000 1200 1400 1600 1800 2000 2200 2400 2600 Q [m³/h]
108
Performance curves HS 350-300-508
6-pole
Dimensional sketch
HS extended, 350-300-508
109
Technical data HS 400-350-397
6-pole
H
[m]
36 HS 400-350-397
/396.2
34
60 Hz, n = 1180 min-1
ISO 9906 Grade 2
32
/373.4
30
28 /350.5
26
/327.7
24
22
/304.8
20
18
16
14
12
10
NPSH
8
[m]
6 12
4 8
2 NPSH 4
0 0
0 200 400 600 800 1000 1200 1400 1600 Q [m³/h]
P2 Eta
[kW] [%]
180 90
160 80
/396.2
140 /350.5 /373.4 70
/327.7
120 /304.8 60
100 50
/396.2
80 /373.4 40
60 /350.5 30
/327.7
40 /304.8 20
20 10
TM03 9878 4507
0 0
0 200 400 600 800 1000 1200 1400 1600 Q [m³/h]
110
Performance curves HS 400-350-397
6-pole
Dimensional sketch
HS extended, 400-350-397
111
Bare shaft pump HS
Dimensional sketch
CP Key (WxL)
Pump size DNs DNd A AE B BP D DH G ∅HH HZ
Sealed Packed [inch] [mm]
HS65-50-242 65 50 305 260 222 178 510 545 178 89 16 19 270 0.25x2.12 6.35x53.85
HS65-50-331 65 50 305 260 222 178 510 545 216 89 16 19 355 0.25x2.12 6.35x53.85
HS100-80-242 1) 100 80 305 260 222 178 510 545 203 102 19 19 290 0.25x2.12 6.35x53.85
HS100-80-242 2) 100 80 305 260 222 178 510 545 203 102 19 19 290 0.25x2.12 6.35x53.85
HS100-80-356 100 80 305 260 279 235 644 687 254 127 22 19 380 0.38x2.25 9.65x57.15
HS125-100-280 125 100 305 260 283 235 631 674 257 124 22 19 370 0.38x2.25 9.65x57.15
HS125-100-305 125 100 305 260 283 235 631 674 257 124 22 19 370 0.38x2.25 9.65x57.15
HS125-100-381 125 100 305 260 349 305 631 674 330 159 25 19 470 0.38x2.25 9.65x57.15
HS150-125-305 150 125 305 260 305 260 775 775 368 165 25 19 475 0.38x2.25 9.65x57.15
HS150-125-381 150 125 305 260 305 260 801 801 410 165 25 19 550 0.38x2.25 9.65x57.15
HS200-150-305A 200 150 305 260 305 260 656 699 330 165 25 19 430 0.38x2.25 9.65x57.15
HS200-150-305C 200 150 305 260 305 260 801 801 406 165 25 19 530 0.38x2.25 9.65x57.15
HS200-150-381 200 150 311 260 457 419 929 929 464 184 29 19 605 0.38x2.25 9.65x57.15
HS200-150-483 3) 200 150 305 260 356 305 888 888 432 171 25 19 615 0.38x2.31 9.65x57.74
HS200-150-483 4) 200 150 305 260 356 305 899 899 432 171 25 19 615 0.38x3.00 9.65x76.20
HS200-150-508 200 150 318 260 356 305 995 995 451 171 25 19 660 0.50x3.00 12.70x76.20
HS250-200-305 250 200 305 260 394 356 929 929 438 171 29 19 580 0.38x2.25 9.65x57.15
HS250-200-381 250 200 324 260 495 445 949 949 483 178 29 19 655 0.38x2.25 9.65x57.15
HS300-200-489 300 200 648 502 489 406 1306 1306 529 198 35 29 745 0.63x3.00 16.00x76.20
HS300-250-305 300 250 324 260 495 445 974 974 503 203 29 19 645 0.38x2.25 9.65x57.15
HS300-250-381 300 250 457 381 356 305 1051 1051 508 254 29 22 630 0.50x2.75 12.70x69.85
HS350-250-498 350 250 648 502 489 406 1403 1403 586 246 35 29 785 0.75x4.75 19.05x120.65
HS350-250-630 350 250 648 502 489 406 1377 1377 635 305 35 29 820 0.75x4.75 19.05x120.65
HS350-300-508 350 300 648 502 489 406 1377 1377 643 313 35 29 790 0.63x3.00 16.00x76.20
HS400-350-397 400 350 790 610 657 575 1299 1299 670 320 40 23 800 0.63x3.00 16.00x76.20
1)
Shaft load up to 1.27 kW/100 rpm
2)
Shaft load above 1.27 kW/100 rpm
3)
Shaft load up to 2.7 kW/100 rpm
4)
Shaft load above 2.7 kW/100 rpm
112
Bare shaft pump HS
Dimensional sketch
N U Net weight
Pump size DNs DNd SH W WB WS X YY
Sealed Packed [inch] [mm] [kg]
HS65-50-242 65 50 100 65 89 1.00 25.40 305 416 216 216 216 73
HS65-50-331 65 50 100 65 89 1.00 25.40 305 416 216 254 254 95
HS100-80-242 1) 100 80 100 65 102 1.00 25.40 305 416 216 279 279 80
HS100-80-242 2) 100 80 100 65 102 1.19 30.16 305 416 216 279 279 80
HS100-80-356 100 80 118 75 127 1.50 38.10 368 508 251 305 305 177
HS125-100-280 125 100 106 63 124 1.50 38.10 368 508 251 305 305 164
HS125-100-305 125 100 106 63 124 1.50 38.10 368 508 251 305 305 164
HS125-100-381 125 100 106 63 159 1.50 38.10 368 543 216 357 357 255
HS150-125-305 150 125 63 63 165 1.50 38.10 419 572 289 330 330 268
HS150-125-381 150 125 63 63 165 1.50 38.10 432 584 302 356 381 318
HS200-150-305A 200 150 105 63 165 1.50 38.10 381 533 251 279 330 255
HS200-150-305C 200 150 63 63 165 1.50 38.10 432 584 302 356 406 411
HS200-150-381 200 150 87 87 184 1.75 44.45 508 737 298 381 406 455
HS200-150-483 3) 200 150 305 305 171 1.75 44.45 489 667 337 432 432 534
HS200-150-483 4) 200 150 305 305 171 2.00 50.80 489 667 337 432 432 534
HS200-150-508 200 150 98 98 171 2.13 53.98 546 724 394 432 483 545
HS250-200-305 250 200 87 87 171 1.75 44.45 508 705 330 406 432 511
HS250-200-381 250 200 87 87 178 1.75 44.45 518 765 295 483 483 568
HS300-200-489 300 200 147 147 198 2.50 63.50 723 994 519 414 559 727
HS300-250-305 300 250 87 87 203 1.75 44.45 530 778 308 495 495 636
HS300-250-381 300 250 149 149 254 2.25 57.15 600 778 448 432 584 991
HS350-250-498 350 250 205 205 246 3.13 79.38 797 1049 594 508 660 1436
HS350-250-630 350 250 219 219 305 3.13 79.38 799 1049 594 610 711 1905
HS350-300-508 350 300 121 121 313 2.50 63.50 749 994 546 584 711 1318
HS400-350-397 400 350 142 147 320 2.50 63.50 723 1052 436 550 650 1460
113
Accessories HS
O-ring NBR EPDM 300 x 250 684 350 314 569 430 584 25 15 189
300 x 300 690 367 340 600 410 586 25 15 203
350 x 250 764 380 330 607 460 644 25 15 272
350 x 300 764 379 341 607 460 644 25 15 280
350 x 350 752 370 350 634 460 622 25 15 315
PTG is the diameter of drain role.
PTH is the diameter of a pressure gauge tapping.
114
Accessories HS
Pressure drop
In operation the suction diffuser causes a minor pressure drop.
10000 350A
300A
250A
200A
150A
125A
100A
1000
80A
Flow rate [m3/h]
100
10
115
Accessories HS
Mode of operation
Tighten the activating screw in the bottom of the
cartridge and a gas generating pellet will drop into a
liquid electrolyte starting a chemical reaction. The
pressure built-up inside the unit (up to 4 bar) will push
against a piston, which in turn will push the lubricant out
TM03 3747 0906
Product number
Pt 100 can be ordered using this product number:
95043173.
116
Further product documentation HS
WebCAPS
WebCAPS is a Web-based Computer Aided Product
Selection program available on www.grundfos.com.
WebCAPS contains detailed information on more than
185,000 Grundfos products in more than 20 languages.
In WebCAPS, all information is divided into 6 sections:
• Catalogue
• Literature
• Service
• Sizing
• Replacement
• CAD drawings.
Catalogue
Literature
In this section you can access all the lastest documents of a given
pump, such as
• data booklets
• Installation and operating instructions
• service documentation, such as Service kit catalogue and
Service kit instructions
• quick guides
• product brochures, etc.
Service
117
Further product documentation HS
Sizing 0 1
Replacement
CAD drawings
2-dimensional drawings
• .dxf, wireframe drawings
• .dwg, wireframe drawings.
3-dimensional drawings
• .dwg, wireframe drawings (without surfaces)
• .stp, solid drawings (with surfaces)
• .eprt, E-drawings.
WinCAPS
WinCAPS is a Windows-based Computer Aided
Product Selection program containing detailed inform-
tion on more than 185,000 Grundfos products in more
than 20 languages.
The program contains the same features and functions
as WebCAPS, but is an ideal solution if no Internet
connection is available.
WinCAPS is available on CD-ROM and updated once a
year.
Fig. 47 WinCAPS CD-ROM
118
119
Being responsible is our foundation
Thinking ahead makes it possible
Innovation is the essence
96827075 0408
GB
Subject to alterations.
www.grundfos.com