Professional Documents
Culture Documents
www.agrinol.ua
REFERENCE BOOK
OILS, GEASES, CAR CARE
Production Reference Book. First edition (supplemented and revised) / Edited by
Candidate of Chemical Sciences V. I. Gumenniy — “Agrinol”, 2016 (№2) — 166 p.
The reference book contains brief information about the purpose, fields of
use and normative quality indices of the lubricants produced by the Limited
Liability Company “Agrinol”. The reference book can be used as a guide to choose
and utilize the association’s production.
4
Contents
REFERENCE BOOK
TECHNOLOGICAL
COOLING
LUBRICANTS ....................................... 133
5
OILS
REFERENCE BOOK
8
Agrinol universal multigrade motor oils
REFERENCE BOOK
TS U 23.2-30802090-085:2009
Agrinol 5W30 SL/CF — fuel economy low-viscosity synthetic universal oil for
gasoline and diesel engines of a new generation, adjusted to requirements for architecture
of engine with temperate emissions and low friction, including turbocharged, multivalve
engines and engines equipped with devices pre-treatment of exhaust gases operated
under the regime of "start-stop" and the conditions of urban traffic.
Agrinol 5W30 SM/CF — fuel economy low-viscosity synthetic oil for lubrication of all
gasoline and diesel engines (including turbocharged, multivalve, direct injection), as well as for
cars and off-road vehicles, gas-fueled, in which must apply low viscosity and a low friction oil.
Agrinol 5W40 SN/CF — Universal synthetic oil of new generation, recommended
for modern high-augmented gasoline engines with turbocharging and diesel engines
with supercharge of cars, minibuses and light trucks of European, American and Japanese
manufacturers, sport cars, as well as 4-strokes gasoline engines on motorbikes. Oil increases
the efficiency of fuel consumption while maintaining engine power.
Perfomance level:
Agrinol 5W-30 SL/CF FUEL ECONOMY (ACEA A3/B4/C3, API SL/CF)
VW 502.00/505.00, Ford WSS-M2C913-C/WSS-M2C913-D, BMW LL-01 FE, ACEA A3/B4/C3
9
Agrinol universal multigrade motor oils
REFERENCE BOOK
TS U 23.2-30802090-085:2009
Perfomance level:
Agrinol 5W-40 SL/CF PREMIUM (ACEA А3/B4, API SL/CF)
VW 502.00/505.00, Porsche A40, BMW LL-01, PSA B71 2296, Renault RN0710/RN0700, MB-229.5
10
Agrinol universal multigrade motor oils
REFERENCE BOOK
TS U 23.2-30802090-085:2009
10W-30 SM / CF: — fuel economy universal semi-synthetic motor oil for modern
multi-valve gasoline and diesel engines with hydraulic lifter (including turbocharges) cars,
vans, SUVs and light trucks manufactured after 2004, working under extremely difficult
conditions (idling, "start-stop" mode all year round, including the cold winter). It can be
used in diesel engines released after 1994 on diesel fuel with a sulfur content up to 0.5%.
10W-40 CI-4 / SL: universal semi-synthetic oil for high-speed four-stroke
gasoline and diesel engines of cars and trucks, multi-valve, turbocharged (including
the exhaust gas recirculation system (EGR) with direct injection. The optimal solution
for the mixed fleets.
Agrinol SAE 10W-40 CI-4 – is a universal semi-synthetic motor oil, Low SAPS
category (with low content of Sulphated Ash, Phosphorus and Sulphur), for high-speed
four-cycle engines with different types of fuel injection and supercharging (models from
2002 manufacturing year). For engines with systems of Exhaust Gase Recirculation (EGR).
Perfomance level:
Agrinol 10W-30 SM / CF FUEL ECONOMY (ACEA А1/В1/С2, API SM/CF)
VW 502.00/505.00, Ford WSS-M2C913-C, МВ 229.1, ACEA А1/В1/С2
Agrinol 10W-40 CI-4 / SL PREMIUM (ACEA А3 / В3 / В4 / E7, API CI-4/SL)
MB-228.3, 229.1, VW 500.00/505.00, Renault (RVI) RLD-2, Volvo VDS-3, MAN 3275, ACEA А3/В3/В4/E7
Agrinol 10W-40 CI-4 PREMIUM (ACEA E7 / E5 / E3 / B3 / B4, API CI-4)
BMW LL-98, MB-228.3, MAN M3275, Mack EO-M Plus, RVI RLD / RVI RLD-2, Volvo VDS-2 / VDS-3,
CAT ECF-1-a, Global DHD-1, Cummins CES 20076 / 77 / 78, Jaso DH-1, MTU Type 2, ACEA E7 / E5 / E3 / B3 / B4
11
Agrinol universal multigrade motor oils
REFERENCE BOOK
TS U 23.2-30802090-085:2009
12
Agrinol universal multigrade motor oils
REFERENCE BOOK
TS U 23.2-30802090-085:2009
13
Agrinol universal multigrade motor oils
REFERENCE BOOK
TS U 23.2-30802090-085:2009
Agrinol 15W-30 SF/CE — universal tractor oil used in all types of diesel
engines, including: turbocharged, hydraulic systems, hydrostatic and mechanical
transmissions, wet brake systems and multi-disc clutches, power shafts and
hydraulic boosters for all types of tractors.
Agrinol 20W-40 SF/CC, Agrinol 20W-50 SF/CC are mineral-based multi-grade
engine oils. Oils are designed for the lubrication of all gasoline and diesel engines
in passenger cars of domestic and foreign production, including a turbocharged
heavy-duty engines.
Oil Agrinol 20W-50 SF/CC is specially adapted for engines with high degree
of deterioration and equipment working in the southern regions.
Perfomance level:
Agrinol 20W-40 SF/CC STANDARD (ACEA A2/B2, API SF/CC)
MIL-46152-C; -46152E, CCMC G2/D1
14
Oils for automotive diesels
REFERENCE BOOK
TS U 23.2-30802090-085:2009
Agrinol SAE 10W CF-4 oil is designed for the lubrication of locomotive
and marine diesel engines, bulldozer diesel engines of domestic and foreign
production, metallurgical equipment of mining enterprises, various diesel
engines operating in different conditions, drilling equipment etc.
Agrinol SAE 30 CF-4 and Agrinol SAE 40 CF-4 oils are designed for diesel
engines of heavy trucks, mining and construction equipment operating under severe
conditions. Agrinol SAE 30 CF-4 can be used during the spring and autumn periods the
hydraulic oil ISO 100 in hydrodrives of construction, mining and special equipment.
Agrinol SAE 40 CF-4 can be used in summer or in hot climates.
Agrinol SAE 50 CF-4 il is designed for seasonal use in summer period in the
highly accelerated diesel engines of trucks, road construction, agricultural and
engineering machinery with engines of Euro-I и Euro-II environmental norms,
operating in difficult conditions.
Perfomance level:
Agrinol SAE 10W CF-4 (ACEA E3/B3/B4, API CF-4, ISO VG32)
AllISOn C-3/4 Fluids, Cat TO-2, Vickers 35VQ25 Pump Test, MACK EO-K/2, MAN 270/271
GM 6094-M, MiL-PRF-2104G, -L-46152E
15
Oils for automotive diesels
REFERENCE BOOK
GOST 8581-78
M-8G2, M-8G2k are winter oils for diesel automotive engines, including those
with moderate turbocharging, stationary diesel engines and diesel generators
operating under severe conditions. Temperature range: from minus 20°С to + 25°С.
М-8G2k oil unlike М-8G2 have more effective additive composition, which
increases terms of oil change. Recommended for vehicles of KAMAZ, ZIL type and
for “Ikarus”-type buses.
Operating temperature range: from minus 5°С to + 30°С.
М-8G2k
Index name М-8G2
Extra class First class
Compliance with classifications SAE (API) 20 (СС ) 20 (СС )
Kinematic viscosity at 100°С, mm2/s 8,0±0,5 7,5–8,5
Viscosity index, not less than 85 95 90
TBN, mg КОН/g, not less than 6,0 6,0
Temperature, °С:
• Open cup flash point, °С, not less than 200 210 200
• Pour point, not more than Minus 25 Minus 30 Minus 30
Sulphated ash, %, not more than 1,65 1,15
Degree of purity, mg on 100 g of oil, not more
500 450 500
than
Mass fraction of active elements, %, not less
than
0,15 0,19
• Calcium
0,06 0,05
OILS Oils for automotive diesels
• Zinc
0,06 0,05
• Phosphorous
16
Oils for automotive diesels
REFERENCE BOOK
GOST 8581-78
М-10G2k
Index name М-10G2
Extra class First class
Compliance with classifications SAE (API) 30 (СС ) 30 (СС )
Kinematic viscosity at 100°С, mm2/s 11,0±0,5 11,0±0,5
Viscosity index, not less than 85 95 85
TBN, mg КОН/g, not less than 6,0 6,0
Temperature, °С:
• Open cup flash point, °С, not less than 205 220 205
• Pour point, not more than Minus 15 Minus 18 Minus 15
Sulphated ash, %, not more than 1,65 1,15
Degree of purity, mg on 100 g of oil, not more
500 450 500
than
Mass fraction of active elements, %, not less
than
0,15 0,19
OILS Oils for automotive diesels
• Calcium
0,06 0,05
• Zinc
0,06 0,05
• Phosphorous
17
Oils for automotive diesels
REFERENCE BOOK
GOST 8581-78
Agrinol М-14G2k is intended for lubricating of four-stroke transport diesel
engines, highly accelerated automotive diesels without supercharging (or with
limited supercharging), that operate under moderate and heavy conditions.
Agrinol М-14G2k oil can be used instead of М-10G2k motor oil according to GOST
8581 for summer operation of automotive diesels in regions with long and hot
summers. Temperature range: from minus 20°С to +40°С.
18
Oils for automotive diesels
REFERENCE BOOK
GOST 8581-78
М-8DM, М-10DM — oil is intended for summer use for highly accelerated
automotive diesels, high-speed stationary diesels and diesel generators
of domestic and foreign production with turbo charger and without it, tractors,
bulldozers, dump trucks, in heavy operating conditions or fuel, which vary
in quality (including sour). Operating temperature range: summer oil М-10DM
from minus 5°С to +30°С, winter oil М-8DM: from minus 20°С to +25°С.
19
Universal mineral motor oils
REFERENCE BOOK
GOST 8581-78
М-8V — winter oil for medium augmented automotive diesel engines (ZIL-
130, GAZ-66,51, KaVZ, KAZ, PAZ, LIAZ). Also used in a medium augmented
gasoline engines of cars and trucks (replacement intervals up to 18 thousand
km). Can be applied in such medium augmented automotive diesel engines
as SMD-14, А-41, D-50, D-37, etc., which are running on high sulfur fuel. Operating
temperature range: from minus 20°С to +25°С.
М-6z/12G1 — multigrade oil for lubrication of boosted gasoline engines
of passenger cars in regions with moderate climate and air temperature ranged
from minus 20°С to +45°С.
20
Oils for 2- and 4-stroke engines
of small machinery REFERENCE BOOK
TS U 23.2-36451680-137:2010
Agrinol Moto Racer 2T — low ash, mineral oil for the lubrication of modern
two-stroke gasoline engines of average power, such as: chain saws, lawn mowers,
boat motors, motorcycles, mopeds, etc.
Recommended ratio of the fuel mixture is: 1:40 (oil: gasoline).
Agrinol Aqua Moto 2T — low ash, semisynthetic oil for the lubrication
of modern 2-stroke boat motors (including overhead) with water coolance (boats,
motor boats, jet skis, jet skis), as well as engines of snowmobiles, motorcycles,
chainsaws and other portable equipment with a variety of oil supply methods (by
adding a gasoline or by injection through the nozzle).
Recommended ratio of the fuel mixture is: 1:50 (oil: gasoline).
21
Oils for 2- and 4-stroke engines
REFERENCE BOOK
of small machinery
TS U 23.2-36451680-137:2010
Agrinol Moto Drive 2T — low ash, semisynthetic oil for the lubrication
of modern two-stroke gasoline engines of medium and high power, such
as: chainsaws, snowmobiles, karts, motorcycles, mopeds, and others. Oil
is recommended for use both in mixture and in separate fuel and oil supply.
Recommended ratio of the fuel mixture is:
– for snowmobiles, motorcycles, etc. — 1:50 (oil: gasoline);
– for lawn mowers, chainsaws — 1:40 (oil: gasoline).
Agrinol Moto Drive 4T — low ash, semisynthetic engine oil designed
to lubricate the modern four-stroke engines of motorcycles, ATVs, scooters and
other motor vehicles with any clutch, mobile equipment, water-cooled outboard
boat engines.
Traces Traces
• Mechanical impurities None None
Temperature,°С:
• Open cup flash point, °С, not less than 80 205
• Pour point, not more than -30 -32
Sulphated ash, %, not more than 0,1 1,5
Mass fraction of active elements, %, not less
than:
0,04 0,25
• Calcium
- 0,11
• Zink
22
Oils for marine and locomotive engines
REFERENCE BOOK
GOST 12337-84
М-14V2 oil is intended for use in two-and four-stroke diesel and marine diesel
engines of trunk piston type, operating on distillate fuels with sulfur content
up to 0,5 % (mass fraction), as well as for engines of open- pit dump trucks. Also
it can be used in southern areas as summer oil, instead of М-10V2.
М-16G2TsS is intended for lubricating of the trunk piston of cylinders (high
degree of forcing), crosshead (low-speed) of diesel engines with not more than
1,5 % of sulfur in fuel.
Agrinol Marine TBN 15 – marine engine oils developed for high-performance
trunk piston engines of average speed, which operates on distillate or residual
fuel with the content of sulfur of at most 1,5%. It is recommended for all high-
performance trunk engines and reduction gears where such type of lubricant is
determined by the manufacturer.
Agrinol Agrinol
Index name М-14V2 М-16G2TsS Marine Marine
TBN 15 TBN 15
Compliance with classifications SAE (API) 40 (СВ) 50 (СС) 30 (CD) 40 (CD)
Kinematic viscosity at 100°С, mm /s 2
13,5–14,5 15,5–17,0 905 910
Viscosity index, not less than 85 92 9,5-12,5 13,5-16,5
23
Chain Saw Oil
REFERENCE BOOK
TS U 19.2-32365441-206:2016
Special oils series Chain Saw Oil EXPERT– 68, -100, -150 is designed for
lubrication of chainsaw, chain rails (tires) and the leading asterisks of all kinds of
electric and gasoline-powered saws equipped with both manual and automatic
lubrication system.Developed to improve the use of cutting elements chainsaws
any models and classes.
24
Chain Saw Oil
REFERENCE BOOK
TS U 19.2-32365441-206:2016
Special oils series Chain Saw Oil STANDARD is designed for lubrication of
chainsaw, chain rails (tires) and the leading asterisks of all kinds of electric and
gasoline-powered saws equipped with both manual and automatic lubrication
system.
25
Oils for marine and locomotive engines
REFERENCE BOOK
GOST 12337–84
26
Oils for marine and locomotive engines
REFERENCE BOOK
GOST 12337–84
М-20Е70 oil is used for lubrication of the major low-speed marine diesel
engines during the work on low-sulfur heavy fuels (with sulfur content up to 4,5%).
М-20V2F — seasonal oil for marine diesel engines of 12CHN 18/20 and CHN
16/17 type, working with extended terms of oil change in difficult conditions,
conducive to the formation of high temperature deposits.
27
Oils for marine and locomotive engines
REFERENCE BOOK
TS U 23.2-36451680-144:2010
28
Oils for marine and locomotive engines
REFERENCE BOOK
TS U 23.2-36451680-145:2010
Agrinol М-14V is a mineral engine oil used for lubrication of two-and four-
stroke diesel engines of 2D100, D-50 types and similar to them in terms of boosting
shunting and industrial locomotives
TS U 23.2-30802090-122:2009
Agrinol МТ-16P is a seasonal mineral oil for lubricating of diesel engines of B2
type vehicles and its analogs in terms of forcing the naturally aspirated diesel
engines: automotive diesel engines of old models, marine, locomotive, stationary
and transport naturally aspirated diesel engines.
GOST 12337–84
М-20G2 — season mineral engine oil used for lubricating of high-speed
vessels, diesel and other diesel engines. Provides lubrication for two-stroke diesels
of MD 23/2×30 type.
29
Transmission oils
REFERENCE BOOK
TS U 23.2-30802090-120:2009
Transmission
30
Transmission oils
REFERENCE BOOK
TS U 23.2-36451680-153:2010
Agrinol MULTIPLEX GL-5 SAE-90 is a universal gear oil used for lubrication
of reducers of rolling mills, mechanical transmissions with all types of gears
including hypoid (drive axles, transfer cases, etc) of cars, trucks and tractors,
metallurgical equipment, which operate under severe conditions, where oils
of ТМ-5 (API GL-5) level are needed.
MULTIPLEX SAE 140 GL-5 - transmission oil for the lubrication of loaded
axles and gears of all types: cylindrical, conical, spiral bevel and hypoid gear
off-road vehicles, trucks, buses, tractors, road and construction equipment,
operating in the most severe operating conditions that require compliance with
standards API GL- 5.
31
Transmission oils
REFERENCE BOOK
Transmission oils in accordance with GOST 23652-79
GOST 23652–79
Oil TAp-15V is intended for lubricating of transmissions of trucks, road
construction equipment and gears (spur, spiral bevel gearings and worm-type
gears where the contact stresses are up to 2000 MPa and oil temperature
is up to 130 °C). In the middle climatic zone this oil is used all year-round
at temperatures up to minus 25 °C.
TAD-17i oil is intended for lubricating of all types of gears (including hypoid)
of cars and other mobile equipment. Multigrade oil, operates at temperatures
up to minus 30 °С. The upper limit of continuous performance is 140 °C.
• At 50°С – 110–120
• At 100°С 15,0±1,0 not less than 17,5
Viscosity index, not less than – 100
Corrosion test (for 3 hours):
• At 100°С (steel and copper plates) Pass –
• At 120°С (copper plates), points, not more than – 2с
Temperature,°С:
• Open cup flash point, °С, not less than 185 200
• Pour point, not more than Minus 20 Minus 25
Tribological characteristics on 4 balls machine
at (20±5) °С, N, not less than:
3283 3687
• Scuff index
490 568
• Critical load
– 0,40
• Wear index (392 Н), mm, not more than
OILS Transmission oils
32
Transmission oils
REFERENCE BOOK
GOST 23652–79
TSp-10 oil is intended for lubricating of heavily loaded cylindrical, bevel and
spiral bevel gears operating under the contact stresses up to 1500 2000 MPa and
temperatures of oil in volume up to (100-110)°С.
Product is a winter oil, operational at the temperatures up to minus 45°С.
TSp-15K oil is a multigrade transmission oil for lubricating of heavily loaded
cylindrical, bevel and spiral-bevel gears of KamAZ heavy-vehicles. Operates
at temperatures up to minus 30°С.
TSp-14gip oil is used in hypoid gears of trucks. It is a multigrade oil, operated
at the temperatures up to minus 30°С.
33
Transmission oils
REFERENCE BOOK
Agrinol Transmission oils
TS U 23.2-30802090-021:2002
Oil ТАp-15V is intended for lubricating of transmissions of trucks, road
construction equipment and gears (spur, spiral bevel gearings and worm-type
gears where the contact stresses are up to 2000 MPa and oil temperature
is up to 130 °C). In the middle climatic zone this oil is used all year-round
at temperatures up to minus 25 °C.
ТAD-17i oil is intended for lubricating of all types of gears (including hypoid)
of cars and other mobile equipment. Multigrade oil, operates at temperatures
up to minus 30 °С. The upper limit of continuous performance is 140 °C.
Agrinol ТSzp-8 oil is designed for all seasons use in in the northern regions
and in winter in average climatic zones, lubricating aggregates of transmissions
that have planetary gear transmissions and hydraulic control systems of some
other mobile vehicles. This is transmission transport machinery, spur, helical-
bevel and worm gears operating under conditions of contact stresses up to
20,000 kg/cm2.
34
Transmission oils
REFERENCE BOOK
TS U 23.2-36451680-153:2010
TSp-10 oil is intended for lubricating of heavily loaded cylindrical, bevel and
spiral bevel gears operating under the contact stresses up to 1500 2000 MPa and
temperatures of oil in volume up to (110)°С.
Product is a winter oil, operational at the temperatures up to minus 45°С.
TSp-15K oil is a multigrade transmission oil for lubricating of heavily loaded
cylindrical, bevel and spiral-bevel gears of KamAZ heavy-vehicles. Operates
at temperatures up to minus 30°С.
Agrinol TSp-14gip oil designed for lubricating hypoid trucks (mainly GAZ)
and special machines as a year-round temperate climatic zone, where the
recommended oil level TM-5 (API GL-5).
35
Transmission oils
REFERENCE BOOK
Transmission oils for industrial an obsolete equipment
TS U 23.2-30802090-021:2002
Agrinol Nigrol oils are used as working liquids for gearboxes, easy-loaded units
of industrial equipment, open toothed gears, planetary toothed gears of cranes
and excavators, toothed gears and transmission units of industrial equipment,
tractors, agricultural and road-building machines, constructing devices.
36
Transmission oils
REFERENCE BOOK
Automatic transmission fluid
TS U 23.2-36451680-134:2010
37
Universal oils for automotive diesels
REFERENCE BOOK
TS U 23.2-36451680-137:2010
Agrinol STOU SAE 10W-30, STOU SAE 10W-40 – universal series of oils of
STOU class (Super Tractor Oil Universal) for apllication in engines, including
turbocharged, in mechanic transmissions and hydrosystems (hydro and hydraulic
clutches) of tractors and other agricultural and building vehicles. Suit for
apllication in “wetdiscbrakes” of modern special technics.
Perfomance level:
Engines:
АРI CG-4, ACEA E3, SAE J300 10W-30 (10W-40)
MAN 271
Transmission units:
SAE J306 75W-80 (75W-90)
ALLISON C-4, CAT TO-2/TO-4, FORD M2C159 B/C; John Deere JDM J 20 C; MF M1135, 1139, ZF TE-
ML06A
Hydro-systems and hydraulic clutches:
ISO VG 46 / 68 / 100, DIN 51524.2/3 НLP/HVLP-D
AFNOR NFE 48603 HV;
• Open cup flash point, °С, not less than 200 205
• Pour point, not more than –32 –32
38
Universal oils for automotive diesels
REFERENCE BOOK
TS U 23.2-36451680-137:2010
Perfomance level:
Transmission units:
АРI GL-4SAE; J306C 80W 85W; SAE J300; 10W-30; 20W-40; ZF TE-ML 03E, 05F, 06K,17E, 21F;
Allison C3/C4; Caterpillar TO-2; John Deere JDM J 20 C; Ford M2C 134 C/D, M2C 86 B/C;
Hydro-systems and hydraulic clutches:
ISO VG 46 / 68 /100; DIN51524.2/3 HLP/HLP-D
39
Oils for hydromechanical transmissions
REFERENCE BOOK
TS U 23.2-30802090-047:2005
Agrinol A oil is used for multigrade exploitation in torque converters,
automatic transmissions at the environmental temperatures up to minus
35°С. Product can be used as winter oil in the hydrostatic drives of self-propelled
agricultural and other machinery.
Agrinol R oil is used in systems of wheel hydrostrengthenings and hydrostatic
transmissions at the environmental temperature up to minus 40°С.
TS U 23.2-36451680-165:2011
Special Oil HMT is used for multigrade exploitation in torque converters,
automatic transmissions, and hydrostatic transmissions at the environmental
temperatures up to minus 5°С.
17–22
• At 40°С 30–45 30–45
not more than
• At 100°С not less than 6,5 not less than 6,5
5,0
Viscosity index, not less than 90 90 105
Temperature, °С:
• Open cup flash point, °С, not less 175 163 190
than Minus 40 Minus 45 Minus 40
• Pour point, not more than
Mass fraction, %, not more than:
• Mechanical impurities 0,01
• Water None
Mass fraction of active elements, %,
not less than:
0,16 0,16 0,16
• Calcium
0,08 0,8 0,08
• Zinc
Corrosive effect on metals Pass
40
Hydraulic oils
REFERENCE BOOK
Low-temperature oils
TS U 23.2-30802090-067:2006
Hydraulic oil Agrinol VMGZ is used as a winter oil. In Arctic conditions it is used
as а year-round working liquid in hydraulic drives and hydraulic control systems
of constructing, road, logging, lifting and other machines and mechanisms
exploited in the open air at the working temperature of oil from minus 55 °С up
to 80 °С.
GOST 6794–75
AMG-10 oil is designed for use as a working fluid for hydraulic devices operating
in the range of environmental temperatures from minus 60°С to +55 °С.
TS U 23.2-30802090-124:2009
Spindle oil Agrinol AU is intended for use in lightly loaded hydraulic systems
of mobile equipment with gear and piston pumps, working under pressure up to
15 MPa and maximum oil temperature up to 100°С.
Oil supports the work of hydraulic drives in the temperature range from
minus 35°С to plus 100°С.
Index name AMG-10 Agrinol VMGZ Agrinol AU
Compliance with classifications ISO VG 15 15 22
ISO 6743 // DIN 51524 HL // HLP HM // HLP НН
Designation according to GOST 17479.3 МГ-15-Б МГ-15-В МГ-22-А
Kinematic viscosity, mm2/s:
• at 40°С, not less than - - 16,0–22,0
• at 50°С, not less than 10 10 -
• at minus 40°С, not more than - 1500 30000
• at minus 50°С, not more than 1250 - -
Viscosity index, not less than 140
Temperature, °С:
• Open cup flash point, °С, not less
93 135 163
than
Minus 70 Minus 60 Minus 45
OILS Hydraulic oils
41
Power oils
REFERENCE BOOK
Turbine oils according to GOST 9972-74, GOST 10289-79
GOST 9972–74
Turbine oils with additives TP-22, TP-30 and TP-46 are intended for
lubricating and cooling bearings of such various turbo-units as steam and gas
turbines, water turbines, turbocompressor machines, ship steam turbine units
and other analogous types of equipment. These oils are also used as working
liquids for turbo-units’ regulating systems, circulating and hydraulic systems of
diverse industrial mechanisms.
GOST 10289–79
Oil for marine gas turbines (SGT) product is used for lubrication and cooling of
gears and bearings of marine gas turbines.
42
Power oils
REFERENCE BOOK
TS U 23.2-30802090-076:2007
The lubricating oil Agrinol МS-8p is intended for usage in hydraulic and
lubricating and cooling systems of gas-turbine units, gas-pumping units,
equipment of gas pipelines and other industrial equipment. The oil is efficient at
the temperature varying from minus 40°С up to 80°С
43
Power oils
REFERENCE BOOK
Kompressoil VG
TS U 23.2-36451680-156:2010
Kompressoil VG 46, 68, 100 oil is intended for lubricating of pistons (cross-
head, without cross-head, single and multistage) and rotary air compressors
working permanently at 220°С on a blowing line.
Low-viscosity versions of Kompressoil VG oils are used in rotary compressors
(in accordance with the recommendations of manufacturers of compressors).
Kompressoil
Index name
VG 46 VG 68 VG 100
44
Power oils
REFERENCE BOOK
TS U 23.2-36451680-156:2010
Kompressoil VG 150, 220, 320 oil is intended for lubricating of pistons (cross-
head, without cross-head, single and multistage) and rotary air compressors
working permanently at 220°С on a blowing line.
Low-viscosity versions of Kompressoil VG oils are used in rotary compressors
(in accordance with the recommendations of manufacturers of compressors).
Index name
VG 150 VG 220 VG 320
45
Power oils
REFERENCE BOOK
TS U 23.2-30802090-017-2003
GOST 9243-75
GOST 1861-73
Compressor oils K-12 and K-19 are produced from low-sulfur crude oils and
are used for lubricating piston and rotary compressors and blowers.
Oxidation stability:
• Sediment, %, not more than
None None 0,25 0,015
• Acid number, мг КОН/г, not more
0,5 0,5 – –
than
Corrosive effect on metals Pass – Pass
Corrosion on plates of the lead, g/m2, not – 10 –
more than
46
Power oils
REFERENCE BOOK
Compressor oils for gas-transit units
TS U 23.2-36451680-149:2010
GOST 5546-86
Agrinol
Index name Refoil HA-30 HF 12-16 HF 22-24
10KS
Compliance with classifications ISO (DIN
10 (KC) 46 (KA) 22 (KC) 32 (KC)
51503)
Kinematic viscosity, mm2 / s:
• At 20°С - 120-150 - -
• At 40°С 8,0-12,0 - - -
• At 50°С - 28-32 Not less than 17 24,5-28,4
Acid number, mg КОН / g, not more than 0,02 0,05 0,02 0,04
Temperature, °С:
• Open cup flash point, °С, not less than 144 185 174 130
• Pour point, not more than Minus 57 Minus 38 Minus 42 Minus 55
• Flocculation of oil mixed with Freon, - - Minus 50 -
not more than
Oxidation stability:
- 0,02 0,005
• Sediment, %, not more than -
- 0,5 0,04
• Acid number, mg КОН / g, not more than -
0,005 0,004 -
• Ash content, %, not more than -
Mass fraction, not more than:
OILS Power oils
47
Power oils
REFERENCE BOOK
TS U 23.2-30802090-035:2005
48
Power oils
REFERENCE BOOK
Тransformer oils
GOST 982–80
Transformer oils T-1500 and TK are sulfuric and solvent refined oils produced
from low-sulfur crude oils. These products are used as oil circuit breakers (and in
other high-voltage equipment as the primary insulating material).
49
Power oils
REFERENCE BOOK
GOST 10121–76
ТSО transformer oil is used to fill transformers and other oil-filled electrical
equipment.
TS U 23.2-30802090-113:2009
50
Power oils
REFERENCE BOOK
Cable oils
TS U 23.2-30802090-126:2009
51
Industrial oils
REFERENCE BOOK
52
Industrial oils
REFERENCE BOOK
Hydraulic oils of premium group
TS U 23.2-30802090-114:2009
Hydroil HM-10, -22, -32, -46, -68, -80 oils are used as a working liquid for
hydraulic actuators, hydraulic transmissions, and circulating oil systems of different
units, low-and moderate gears and worm gears, variable, electromagnetic, and
gear couplings, bearing units, sliding guides and bearings, and other sites of the
machinery of modern industrial equipment. Products does not contain chlorine
compounds.
Hydroil HM
Index name
10 22 32 46 68 80
10 22 32 46 68 80
Compliance with classifications ISO
HM// HM// HM// HM// HM// HM//
VG ISO 6743 // DIN 51524.2
HLP HLP HLP HLP HLP HLP
Kinematic viscosity at 40°С, mm2 / s 8-14 18-26 28-36 42-50 61-75 76-85
Viscosity index, not less than 108 100 98 97 94 92
Acid number, mg КОН / g, within 0,7
Temperature, °С:
• Open cup flash point, °С, not less 160 170 190 200 210 215
than -30 -27 -24 -24 -24 -20
• Pour point, not more than
Ash content, %, not more than 0,2
Color with dilution 15 / 85, CNT units,
1,0 1,5
not more than
Mass fraction of sulfur, %, not more
0,5 0,8
than
OILS Industrial oils
53
Industrial oils
REFERENCE BOOK
Hydraulic oils of premium group
TS U 23.2-30802090-114:2009
Hydroil HM-100, -120, -150, -200, -270, -330 oils are used as a working
liquid for hydraulic actuators, hydraulic transmissions, and circulating oil
systems of different units, low-and moderate gears and worm gears, variable,
electromagnetic, and gear couplings, bearing units, sliding guides and bearings,
and other sites of the machinery of modern industrial equipment. Products does
not contain chlorine compounds.
Hydroil HM
Index name
100 120 150 200 270 330
100 120 150 200 270 330
Compliance with classifications
HM// HM// HM// HM// HM// HM//
ISO VG ISO 6743 // DIN 51524.2
HLP HLP HLP HLP HLP HLP
Kinematic viscosity at 40°С, mm2/s: 320-
90-110 110-125 148-165 186-205 265-280
348
Viscosity index, not less than 91 90 90 90 90 90
Acid number, mg КОН/g, within,
0,7
within
Temperature, °С:
• Open cup flash point, °С, not 220 220 225 230 230 240
less than -18 -15 -15 -15 -15 -15
• Pour point, not more than
Ash content, %, not more than 0,2
Color with dilution 15:85, CNT
1,5 2,0
units, not more than
Mass fraction of sulfur, %, not
0,8 1,0
more than
OILS Industrial oils
54
Industrial oils
REFERENCE BOOK
TS U 23.2-36451680-155:2010
Agrinol Hydraulic Lift oils are designed for use as working fluids for hydraulic
drives, hydraulic transmissions and circulating oil systems of different industrial
units and machinery operating under extreme loads (pressures above 25 MPa).
Hydraulic Lift
Index name
22 32 46 68 100
22 32 46 68 100
Compliance with classifications ISO VG
HM// HM// HM// HM// HM//
ISO 6743 // DIN 51524.2
HVLP HVLP HVLP HVLP HVLP
Kinematic viscosity at 40°С, mm2 / s: 18-26 28-36 41-51 61-75 90-110
Viscosity index, not less than 130
Acid number, mg КОН / g, within 0,5-1,0
Temperature, °С:
• Open cup flash point, °С, not less 160 170 180 190 200
than -40 -40 -40 -38 -38
• Pour point, not more than
Ash content, %, not more than 2,0
Color with dilution 15:85, CNT units, not 5,0
4,5 5,5 5,5 6,0
more than
Mass fraction of water, %, not more than None
Mass fraction of mechanical impurities, None
%, not more than
Corrosive effect on metals Pass OILS Industrial oils
55
Industrial oils
REFERENCE BOOK
Zinc-free hydraulic oils of premium group
TS U 23.2-36451680-155:2010
Oil Hydroil HM Ultra is used as the working fluid for hydraulic actuators,
hydraulic transmissions and circulating oil systems of different units, low-and
moderately loaded gearboxes and worm gears, CVTs, electromagnetic clutches
and gear, bearing units, sliding and rolling rails and the other nodes in the
machinery of modern industrial equipment.
For hydraulic systems, which cannot contain Zn-based additives.
Hydroil HM Ultra
Index name
22 32 46 68 100
22 32 46 68 100
Compliance with classifications ISO VG
HM// HM// HM// HM// HM//
ISO 6743 // DIN 51524.2
HLP HLP HLP HLP HLP
Kinematic viscosity at 40°С, mm2 / s: 18-26 28-36 42-50 61-75 90-110
Viscosity index, not less than 100 100 100 95 91
Acid number, mg КОН / g, within 0,3
Temperature, °С:
170 190 205 210 220
• Open cup flash point, °С, not less than
-30 -30 -30 -25 -20
• Pour point, not more than
Ash content, %, not more than 0,1
Color with dilution 15 : 85, CNT units, not
1,0 1,5
more than
Tribological characteristics on 4 balls
machine at (20±5) °С, not less than:
• Diameter of the wear spot (196 Н), mm, 0,4
OILS Industrial oils
56
Industrial oils
REFERENCE BOOK
Gear oils premium group
TS U 23.2-30802090-102:2009
Highrate XP oil series is designed for the lubrication of all types of toothed,
worm and helical gears and gear units with closed circulatory systems of
lubrication. Product also can be used for the lubrication of various industrial
spray equipment: metal cutting and woodworking machines, presses, casting
and molding machines, rolling mills, mixers, dryers, extruders, fans, crushers,
pumps, conveyors, elevators, lifts, rotary kilns, calenders, machines for paper
production, coal combines, etc.
In ship equipment oil is used to lubricate gears, centrifuges, winches,
windlasses, cranes, rotating machinery, pumps, hoists and lifting equipment of
steering mechanism.
Highrate XP
Index name
68 100 150 220 320 460 680
Compliance with classifications 68 100 150 220 320 460 680
ISO VG DIN 51517.3 CLP CLP CLP CLP CLP CLP CLP
Kinematic viscosity at 40°С, 140- 190- 300- 420- 610-
61-75 90-110
mm2 / s: 160 240 350 510 750
Viscosity index, not less than 100 100 97 94 92 90 90
Acid number, mg КОН / g, within 2,0 2,0 2,5 3,0 3,0 3,5 3,5
Temperature, °С:
• Open cup flash point, °С, not 210 220 225 230 230 240 245
less than
• Pour point, not more than -24 -24 -24 -18 -15 -12 -12
Mass fraction, %, not more than:
• Mechanical impurities 0,01 0,01 0,01 0,02 0,03 0,03 0,05
• Water Traces Traces Traces Traces Traces Traces Traces
Tribological characteristics on 4
balls machine (20±5)°С:
• Scuff index, Н, not less than 392 392 392 490 490 490 490
OILS Industrial oils
• Index of wearout (196Н), mm, 0,45 0,45 0,45 0,45 0,40 0,45 0,45
not more than
57
Industrial oils
REFERENCE BOOK
TS U 23.2-36451680-166:2010
Special Oil ART gear oils are designed for lubrication of all types of toothed,
worm and helical gears of various industrial equipment: metal cutting and
woodworking machines, hammers, presses, casting and molding machines,
winches, rolling mills, overhead cranes, conveyors, elevators, lifts, rotary cement
ovens, calenders, equipment for the manufacture of paper, coal combines, textile
and spinning machines and other equipment where high loads do not allow using
of oil without additives.
58
Industrial oils
REFERENCE BOOK
For rolling mills
TS U 23.2-30802090-097:2008
Industrial oils Agrinol I100PV are intended for lubricating of liquid friction
bearings of roller mills, equipped with circulating lubrication systems with long
pipelines and branching, as well as with the oil line of small diameter, where
ingress of water is possible.
The main consumers of oil are companies of steel industry.
59
Industrial oils
REFERENCE BOOK
GOST 12672–77
PS-28 is an oil, intended for lubrication of heavily loaded rolling mills with a
circulating lubrication systems (other than liquid friction bearings).
TS U 23.2-30802090-011:2002
Agrinol PS-20 and Agrinol PS-28z oils are used as lubricating oils for
circulating greasing of systems of rolling mills, reducers, rolling equipment units
of average and heavy loading, equipment of tyre factories etc. (except bearings
of fluid friction).
60
Industrial oils
REFERENCE BOOK
Oils for slideways
TS U 23.2-36451680-147:2010
Agrinol İNSp oil series is designed for lubrication of sliding and rolling
machine tools, heavy gears of drive screws of especially high precision with
program control, which require uniformity of the slow movement, accuracy and
sensitivity of the displacement tables.
61
Industrial oils
REFERENCE BOOK
Oils for liquid friction bearings
TS U 23.2-30802090-008:2002
Agrinol PZhT oil series is designed for lubrication of horizontal and vertical
liquid friction bearings of rolling mills equipped with circulating systems with
pipe-lines of various lengths and branching with possible irrigation.
62
Industrial oils
REFERENCE BOOK
GOST 6411–76
Heavy cylinder oils – petroleum oils, are intended for lubricating of the
reciprocating steam engines of different purposes, working in superheated steam
(C-38 up to 350°С, C-52 up to 400°С) under heavy loads and low speeds.
63
Industrial oils
REFERENCE BOOK
General purpose oils
TS U 23.2-30802090-013:2003
Agrinol МS-20 oil does not contain active additives. It is intended for the
usage in industrial equipment of rolling mills, reducers and other equipment of
metallurgical, mining, woodworking enterprises. For terrestrial applications.
Agrinol МS-20p and Agrinol МS-20ps oils are generally used as lubricating
oils in those cases when high requirements to exploitation properties, especially
for anti-deterioration and washing properties of oils are necessary.
Agrinol MS-20gk is intended for use as grease in the lubricating system
of gas motor compressors 10GKNA, MK8 and / or in other similar units. Oil
consumers are enterprises of metallurgy, mining, mining and timber industries,
paper manufacturing companies.
64
Industrial oils
REFERENCE BOOK
Industrial petroleum oils
GOST 20799–88
Industrial oils I-5А, I-8А, I-12А, I-12А1 are refined distillate and residual
oils or it’s mixtures without any additives. These oils are used for machines and
mechanisms of industrial equipment that does not impose specific requirements
to anti-oxidation and anti-corrosion properties of oils. These products can also
be used as hydraulic liquids.
65
Industrial oils
REFERENCE BOOK
TS U 23.2-30802090-061:2006
Industrial oils I-20А, I-30А, I-40А, I-50А are refined distillate and residual
oils or it’s mixtures without any additives. These oils are used for machines and
mechanisms of industrial equipment that does not impose specific requirements
to anti-oxidation and anti-corrosion properties of oils. These products can also
be used as hydraulic liquids.
66
Heat-treatment oils
REFERENCE BOOK
TS U 23.2-30802090-023:2004
67
Heat-treatment oils
REFERENCE BOOK
TS U 23.2-30802090-074:2008
68
Heat-treatment oils
REFERENCE BOOK
TS U 23.2-30802090-082:2009
69
Heat-treatment oils
REFERENCE BOOK
ТУ У 23.2-30802090-090:2008
70
Heat-treatment oils
REFERENCE BOOK
Vacuum oils
TS U 23.2-30802090-031:2006
Vacuum petroleum oils of Agrinol VM series are used as the working fluid for
mechanical vacuum pumps.
Agrinol VМ-1 oil is used as a working liquid in high-vacuum steam-jet pumps
of BN-3 series, which work at the residual pressure from 1*10 -3 to 1*10 -6 mm of
mercury.
Agrinol VМ-3 is used as a working liquid in high-production oil-vapor booster
pumps which work at the residual pressure from 1*10 -2 to 1*10 -4 mm of mercury.
Agrinol VМ-4 oil is used as a working liquid in mechanical vacuum pumps
with oil seal.
Vapor pressure at 20°С, Pa, not more than 5,3·10-6 1,33·10-2 5,3·10-3
Density at 20°С, kg/m2, not more than 900 890 908
71
Heat-treatment oils
REFERENCE BOOK
Oil heat transfer fluid
TS U 23.2-30802090-031:2006
Agrinol VM-5 oil is used as the working fluid in a high-vacuum steam jet
pumps, which operate at a residual pressure of 1*10 -3 to 1*10 -7 mm Hg. of Art.
Agrinol VM-6 used as a lubricating material and seal for piston backing
pumps, working at a residual pressure of 1*10 -3 mm Hg. of Art.
Agrinol VM-11 oil is used as the working fluid in a high-performance steam
booster, auxiliary and steam-jet and special fore-vacuum pumps.
72
Heat-treatment oils
REFERENCE BOOK
Flushing oils
TS U 23.2-30802090-050:2006
Agrinol MP and Agrinol MP Plus flushing oils are designed for irrigation of
automotive engine lubrication systems without disassembly (while replacement
of oil).
TS U 23.2-30802090-080:2008
73
Heat-treatment oils
REFERENCE BOOK
Conservative oils
GOST 10877–76
TS U 23.2-30802090-111:2009
Agrinol Gun Oil VO and Agrinol Gun Oil RG oils are designed for short-term
protection of metal surfaces from corrosion and as lubricating oils for unloaded
nodes.
Temperature of application: Agrinol Gun Oil VO — above 5 °C, Agrinol Gun Oil
RG — up to minus 50 °C.
TS U 23.2-30802090-111:2009
74
Heat-treatment oils
REFERENCE BOOK
Release agent Form Divider
TS U 24.6-30802090-106:2008
75
Heat-treatment oils
REFERENCE BOOK
Instrumental oils
GOST 1805–76
GOST 18375-73
76
77
REFERENCE BOOK
OILS
78
REFERENCE BOOK
Grease
Grease
79
REFERENCE BOOK
80
General-purpose lubricants
for standard temperatures REFERENCE BOOK
TS U 30802090.001-2000
Grease
81
General-purpose lubricants
REFERENCE BOOK for standard temperatures
GOST 3333–80
82
General-purpose lubricants
for standard temperatures REFERENCE BOOK
Red calcium grease - rough friction units of rolling and sliding of machines
and mechanisms of vehicles, agricultural machines, hand tools, screw and chain
drives, low-speed gear reducers, etc.
Green rubber grease - rough friction units of rolling and sliding of machines
and mechanisms of vehicles, agricultural machines, hand tools, screw and chain
drives, low-speed gear reducers, etc. Contain rubber.
83
General-purpose lubricants
REFERENCE BOOK
ТУ У 24.6-36451680-148:2010
Colloid stability, % of separated oil, not more than 20,0 15,0 12,0
Effective viscosity at 0°С and with average gradient
1500 1500 (25°С) 1600 (25°С)
of the strain rate 10 s−1, Pa·s, not more than
Evaporation at 150°С for 1 hour, %, not more than 5,0
Tribological characteristics on 4 balls machine at
(20±5) °С, H, not less than 3685 3685 3685
• welding load,
Dropping point, °С, not less than 185 190 190
Mass fraction of free alkalis in NaOH equivalent, %, mg
0,2
КOH / g, not more than
84
Automotive lubricants
REFERENCE BOOK
TS U 23.2-30802090-040:2005
Grease Agrinol ShRUS - 4 is used for lubricating the constant velocity (CV-)
joints of front wheel drive cars, cars with four-wheel drives, and double-row ball
bearings, which are used in the nodes of the hubs of cars VAZ, ZAZ and AZLK.
TS U 23.2-30802090-079:2007
Agrinol Fiol-2U is used for greasing of needle bearings and spline joints of
trunnion of driveshaft for VAZ cars and other vehicles.
85
Automotive lubricants
REFERENCE BOOK
TS U 23.2-30802090-062:2006
Agrinol №158 greases are used for lubrication of roller bearings of automotive
and tracktor equipment, needle bearings of cardan joints of unequal angular
velocities. Agrinol №158M is distinguished by improved anti-wear characteristics
and is recommended for usage in friction units with increased loads and low
sliding speeds, such as constant velocity joints, and front-wheel-drive vehicles as
well as in two-row ball bearings, which are used in hub nodes of cars.
TS U 23.2-30802090-043:2005
Agrinol Agrinol
Index name Agrinol ShRB-4
No158 No158M
TS U 23.2-36451680-127:2011
87
Multi-purpose lubricants
REFERENCE BOOK
TS U 23.2-36451680-127:2011
88
Multi-purpose lubricants
REFERENCE BOOK
TS U 23.2-36451680-127:2011
89
Multi-purpose lubricants
REFERENCE BOOK
TS U 23.2-36451680-127:2011
90
Multi-purpose lubricants
for standard and high temperatures REFERENCE BOOK
TS U 23.2-30802090-014:2002
GOST 1957–73
Konstalin-1 Konstalin-2
Index name Agrinol 1-13
grease grease
91
Industrial lubricants
REFERENCE BOOK
Water-resistant
TS U 23.2-30802090-132:2009
92
Industrial lubricants
REFERENCE BOOK
GOST
TS U 23.2-30802090-126:2009
20.5-32365441-207:2016
93
Industrial lubricants
REFERENCE BOOK
GOST
TS U 23.2-30802090-126:2009
20.5-32365441-207:2016
94
Industrial lubricants
REFERENCE BOOK
ТS U 20.5-32365441-192:2014
Agrinol Polynol HDS 460 recommended for lubrication of low- and middle-
speed industrial bearings, working at high temperature and high loads in
chemical, paper industry, casting and rolling mills, recommended for lubricating
by centralized grease system: live rollers in Continuous Casting Machines;
conveyer rollers in continuous furnaces; for other high temperature applications,
such as:annealing furnace, drying ovens; friction bearing in pouring cranes; hot
rollers in manufacturing of carton; asphalt pavers.
Shear strength at 50°С, Pa, not less than 140-600 1,0-4,0 150
Evaporation, %, not more than 3 3 2
Water resistance, grade, not less than 1c 1c 1c
Stability against oxidation, mg KOH/g,
1 1 0,5
not more than
Lubricating properties at the 4-ball
friction machine:
• Welding load, N, not less than 3283 3283 3283
• Critical load, not less than 1098 1098 1235
• Scuff index, not more than 440 440 -
• Wear out rate at 196N, mm, no more than 0,4 0,4 0,38
95
Industrial lubricants
REFERENCE BOOK
Bentol-1 M intended for the lubrication of plain and rolling bearings operating
at low speed and high temperature or under cyclical temperature changes from
room temperature to high.
Particularly suited for the lubrication of plain bearings of mechanisms,
operating at long relubrication intervals, low speeds or exposed shock loading.
96
Industrial lubricants
REFERENCE BOOK
TS U 23.2-30802090-084:2008
Lubricants for rolling mills Sliding GR are designed for the lubrication of
roller bearings of rolling mills, heavy duty rollers and ball bearings of nodes of
industrial equipment.
Semi-fluid greases Sliding GR 00 and Sliding GR 0 are intended for use in
centralized continuous lubrication systems.
97
Industrial lubricants
REFERENCE BOOK
TS U 23.2-30802090-084:2008
Lubricants for rolling mills Sliding GR are designed for the lubrication of
roller bearings of rolling mills, heavy duty rollers and ball bearings of nodes of
industrial equipment.
Sliding GR1 — for centralized systems of continuous lubrication.
Sliding GR2 is used as mortgage grease.
98
Industrial lubricants
REFERENCE BOOK
Sliding EP2 SHC 220 - grease of wide application for operation under
high pressure, which is recommended for use in heavy vehicles and industrial
equipment.
Recommended operating temperature range for the Sliding EP2 SHC 220
from -45 ° C up to 170 ° C.
99
Industrial lubricants
REFERENCE BOOK
TS U 23.2-30802090-032:2006
1500 (0ºC)
Pa·s, not more than
Tribological characteristics on 4 balls machine at (20±5) °С,
N, not less than
• Welding load 6174
• Critical load 980
• Scuff index 750
• Deterioration rate (196 Н), mm, not more than 0,7
100
Industrial lubricants
REFERENCE BOOK
TS U 30802090.002:2000
Agrinol IP-1l (summer) and Agrinol IP-1z (winter) are antifriction water-
resistant greases for centralized lubrication systems of rolling mills, blast
furnaces and other large-sized equipment of metallurgical enterprises.
These greases are intended for lubricating of friction units of industrial
equipment functioning at the average and heavy losses.
101
Industrial lubricants
REFERENCE BOOK
TS U 23.2-30802090-087:2008
Agrinol Uniol-2M grease are used for greasing of rolling mills, blast furnaces
and other large equipment of metallurgical enterprises. Agrinol Uniol-2M-1
grease is used for greasing of embedded parts, and lubricant grease Agrinol
Uniol-2M-2 — for centralized lubrication systems.
TS U 23.2-30802090-045:2005
Agrinol
Agrinol Agrinol
Index name ProkatOl
Uniol-2M-1 Uniol-2M-2
ЕР 2
Compliance with classifications NLGI 2 0/1 1/2
DIN 51502 KP2P-20 KP0/1P-30 KP1/2Р-10
Appearance Homogeneous grease from
light-yellow to dark-brown
color
Thickener Li complex Li complex
Operating temperature range, min…max, °С -10..+150 -20..+150 -10 … 150
(+170) (+170) (+170)
Dropping point, °С, not less than 230 245
Penetration at 25°С, mm·10 −1 265-320 320-380 265-320
Grease Industrial lubricants
102
Industrial lubricants
REFERENCE BOOK
TS U 23.2-36451680-127:2010
LubriLiCa
Index name
WR 1 WR 2 WR 3
103
Industrial Greases
REFERENCE BOOK
TS U 23.2-36451680-127:2010
LubriLiCa
Index name
EP 1 EP 2 EP 3
104
Industrial Greases
REFERENCE BOOK
Metal-plating lubricants
TS U 23.2-30802090-081:2007
105
Industrial Greases
REFERENCE BOOK
Industrial lubricants for rolling mills
TS U 23.2-30802090-086:2008
Rolling GR are industrial greases for rolling mills designed for centralized
lubrication systems, blast furnaces, rolling and sliding bearings, hinges, screw
and chain drives, low-speed reducers, friction units of transport machinery, hand
tools and agricultural equipment.
Rolling GR S — summer grease, Rolling GR W — winter grease.
Rolling GR SW — for multigrade application.
106
Railway Greases
REFERENCE BOOK
GOST 19791-74
TS U 24.6-30802090-024-2004
107
Railway Greases
REFERENCE BOOK
TS U 23.2-30802090-006-2003
108
Railway Greases
REFERENCE BOOK
TS U 24.6-30802090-058:2006
TS U 24.6-30802090-059:2007
Agrinol ZhT-79L grease is used in brake systems of railway rolling stocks for
lubrication of rubber and rubber-tissue sealing parts of break systems and for
lubrication of friction surfaces: “metal - metal” and “metal - rubber”.
This product also can be used in electrical equipment friction surfaces of
rolling stock: in bearing devices, hinges and all relays, wipers, pressure regulators,
in the cylinders and sealing cuffs of rubber pistons of pneumatic drives of
locomotives and wagons, except the cases of using leather wrist pistons.
TS U 23.2-30802090-100:2009
109
Railway Greases
REFERENCE BOOK
TS U 23.2-30802090-055:2006
Greases Agrinol Relsol M and Agrinol Relsol GS are used for greasing of
“wheel-rail” friction parts of railway transport. Greases are fed into the zone of
wheel pair flanges by the lubricating device with periodic lubrication (grease
Agrinol Relsol М must be fed under the pressure).
TS U 23.2-30802090-075:2007
The metal plating semi-fluid grease Agrinol Puma-M is used for lubricating
of heavy-loaded toothed gears in reducers of locomotive engines as well as for
increasing durability at the contact of wheel pair combs with rails. The lubricant
is placed on wheel combs or cheeks of rails with the help of movable greasing
mechanisms. If the lubricant is placed into friction units, mortgage method is
applied. Agrinol Puma Ml — is summer grease, Agrinol Puma Mz is winter grease.
0/00
Compliance with classifications NLGI 00 000 1/2
G 0/00
DIN 51502 GP00C-30 GP000C-30 G ½ G-40
E-40
Thickener Ca Li
Operating temperature range, min…
-30..+50 -40..+50 -40..+110 -45..+80
max, °С
Dropping point, °С, not less than Not
70 - 140
specified
Penetration at 25°С with stirring (60
440-445 445-495 280-350 350-440
double strokes),
Grease Railway Greases
110
Heat-resistant greases
REFERENCE BOOK
TS U 24.6-32365441-170:2011
Agrinol Termol greases are used in roller bearings and other parts and
mechanisms, which are amenable to high temperatures (for example: circulation
fans of BN gas furnaces, conveyor mechanisms and tunnel kilns).
Agrinol Termol-1 is a synthetic grease with special additives, used in sed in
the operating temperature range from –40 °C to +400 °C.
Agrinol Termol-2 is a mineral based grease used in the temperature range
from –40 °C to +300 °C.
Agrinol Termol greases are clean, non-toxic lubricants.
Pass Pass
GOST 1050)
Mass fraction of water, %, not more than 0,2 0,2
111
Heat-resistant greases
REFERENCE BOOK
TS U 24.6-36451680-148:2010
112
Heat-resistant greases
REFERENCE BOOK
TS U 23.2-30802090-007:2004
113
Heat-resistant greases
REFERENCE BOOK
GOST 9433-80ММ
TS U 23.2-30802090-093:2008
114
Heat-resistant greases
REFERENCE BOOK
GOST 19774–74
VNII NP-207 grease is used in roller bearings of electric machines and starter-
generators with rotation speed of 10,000 min−1.
Product is efficient at residual pressure of 666.5 Pa.
TS U 24.6-30802090-104:2008
TS U 24.6-30802090-088:2008
with a blue
to dark-brown to black color.
tint
color
Thickener Ca complex - Ca complex
Operating temperature range, min…max, °С -50ºC..+180ºC
-60ºC..+200ºC -20ºC..+350ºC
(+200)
Penetration at 25°С, mm·10 −1 Not specified Not specified 300-380
Shear strength, Pa, within:, 80ºC 68,6 Not specified 70,00
Colloid stability, %, not more than 6,0 12 7,0
Effective viscosity with average gradient of
1400 (-30ºC) 750 (-10ºC) 1400 (-30ºC)
the strain rate 10 s−1, Pa·s, not more than
115
Chemically resistant lubricants
REFERENCE BOOK
GOST 8551–74
GOST 14296–78
VNII NP-279 grease is intended for greasing rolling and plain bearings,
threaded joints, connectors, valves, etc., operating in contact with aggressive
media at temperatures ranges from minus 50 °C up to +50 °C and air at
temperatures ranges from minus 50 °C up to +150 °С.
116
Chemically resistant lubricants
REFERENCE BOOK
TS U 24.6-30802090-068:2007
VNII NP-282 A and VNII NP-282M A are designed for designed for sealing
and lubrication of the friction surfaces of various units of equipment operating
at different loads in contact with corrosive environments and gaseous oxygen.
Greases are allowed to use at temperatures up to minus 60°C in powerful
mechanisms, valves and oxygen breathing equipment.
Greases have an increased resistance to oxygen and aggressive environments
(acids, amines, hydrazine), and lower resistance to prolonged contact with nitric
acid and hydrogen peroxide.
117
Drilling lubricants
REFERENCE BOOK
TS U 23.2-30802090-036:2005
TS U 23.2-30802090-116:2011
118
Low-temperature lubricants
REFERENCE BOOK
GOST 11110–75
GOST 8773–73
119
Rope greases
REFERENCE BOOK
TS U 23.2-30802090-110:2009
120
Rope greases
REFERENCE BOOK
TS U 23.2-30802090-115:2009
Agrinol Rope 39U is designed for the lubrication of wire ropes (against
corrosion and premature wearout during operation), including mining and drilling
ropes, working in temperatures ranging from minus 25 °C to +50 °C.
121
Rope greases
REFERENCE BOOK
TS U 23.2-30802090-053:2006
122
Instrumental lubricants
REFERENCE BOOK
GOST 6267–74
GOST 18179–72
OKB-122-7 grease is used in ball bearings and other friction units working in
the temperature range from minus 60 °C to 120 °C.
123
Marine lubricants
REFERENCE BOOK
GOST 2712-75
124
Consrevation (protective) lubricants
REFERENCE BOOK
TS U 23.2-30802090-063:2006
Agrinol ZES grease is used for protection of ground wires and armatures of
high-voltage power lines from corrosion. Product also can be used in various
machines, mechanisms and other metal products made of ferrous and non-
ferrous metals in various conditions (such as: operating, transportation and
storage in open areas).
The lubricant can be used in all climatic zones, including the dry and humid
tropics, sea fog, contact with fresh and sea water, as well as under direct impact
of sunlight beams.
GOST 19537–83
125
Sealing lubricants
REFERENCE BOOK
TS U 24.6-30802090-034:2005
Agrinol Kranol is a sealing grease for gas valves used for lubrication of
shutoff valves of gas appliances, shutoff valves of gas pipelines, gas distribution
and compressor stations at the pressure of 7.5 MPa
GOST 19538–74
ZZK-3u is used for cracks in hatches, lids, doors and other places of machines,
as well as in conservation of machine tools and other equipment, concealed with
housings, sheaths, and shields.
GOST 16862–71
126
Sealing lubricants
REFERENCE BOOK
TS U 23.2-30802090-121:2009
TS U 24.6-30802090-123:2009
Grease Agrinol Armatol-238 is used for the sealing of the locking devices of
mining oil industry equipment from oil, gas and gas condensate fields, which
contain hydrogen sulfide and carbon dioxide to 25 % by volume and operated
in all climatic zones (including areas with cold climates), as well as for various
other valves.
TS U 23.2-30802090-125:2009
Agrinol Rezbol ОМ-2 grease is intended for sealing and corrosion protection
of various pipes: casing, tubing and drilling in the construction and operation of
oil and gas rigs.
Agrinol LZ- Agrinol Agrinol
Index name
162u Armatol-238 Rezbol OM-2
127
Reducer lubricants (semi-fluid)
REFERENCE BOOK
TS U 23.2-30802090-026:2004
GOST 16422–79
NLGI
00 00 1
Compliance with classifications DIN
GHCF00G-40 GP00E-40 GP1H-30
51502
Appearance Homogeneous smooth ointment Homogeneous
from light brown to dark brown viscous black
color liquid
Thickener Li Ca
Operating temperature range, min…
-40..+110 -40..+70 -30..+100
Grease Reducer lubricants (semi-fluid)
max, °С
Dropping point, °С, not less than 150 -
Effective viscosity at 0°С with
1800 (dynamic, at
average gradient of the strain rate 10 1200 1400
minus 30°С)
s-1, Pa·s, not more than
Penetration at 25°С, mm·10 −1 300-360 ((–15°С)
400-430 385-430
Without stirring)
Colloid stability, %, not more than, 10-35 10-30 -
Evaporation, %, not more than 1,5 (100ºC) 0,8 (100ºC) 15,0 (125ºC)
Tribological characteristics on 4 balls
machine at (20±5) °С, N, not less than
• Welding load 1744 2764 6938
• Critical load 696 696 872
• Scuff index 343 392 764
128
Brake- in pastes
REFERENCE BOOK
TS U 23.2-30802090-052:2006
GOST 19782–74
GOST 14068–79
129
Insulation lubricants
REFERENCE BOOK
TS U 24.6-36451680-143:2010
130
131
REFERENCE BOOK
TECHNOLOGICAL
COOLING
LUBRICANTS
133
REFERENCE BOOK
134
Oil coolants
REFERENCE BOOK
GOST 38.01445–88
MR-7, MR-7V are used as cooling lubricants for blade machining, including
vending machines and benches, arbon, alloy, stainless and heat resistant steels,
as well as some hard-alloys. Limitedly applicable in processing of copper and its
alloys. Feeding to the cutting are is performed through irrigation or under the
pressure.
TS U 24.6-30802090-056:2006
135
Oil coolants
REFERENCE BOOK
TS U 24.6-36451680-161:2011
136
Water-based cooling lubricants
REFERENCE BOOK
TS U 24.6-30802090-139:2010
TS U 23.2-30802090-105:2011
137
Water-based cooling lubricants
REFERENCE BOOK
GOST 5702–75
TS U 23.2-30802090-025:2004
TS U 23.2-30802090-022:2003
Agrinol EHP and Agrinol HP technological lubricants are intended for use in
form of (2 5)%-aqueous emulsions (with hardness up to 5 mg-eq/dm3) at the stage
TECHNOLOGICAL COOLING LUBRICANTS Water-based cooling lubricants
138
Water-based cooling lubricants
REFERENCE BOOK
TS U 23.2-30802090-048:2006
TS U 24.6-36451680-091:2010
TS U 23.2-30802090-005:2003
139
Water-based cooling lubricants
REFERENCE BOOK
TS U 23.2-30802090-054:2006
TS U 23.2-30802090-051:2006
Agrinol Akvol-2 and Agrinol Akvol-2E are liquid coolants used in the
processing of doped, stainless, heat-resistant alloys and steels.
Liquids are used for the preparation of (3-10)% emulsions, which are used
in the processing of doped stainless, heat resistant steels and alloys on the
operations of turning, drilling, milling, reaming, threading, broaching, heavy-
duty grinding, as well as for processing of aluminum alloys with cutting.
140
Water-based cooling lubricants
REFERENCE BOOK
TS U 24.6-30802090-083:2009
141
Water-based cooling lubricants
REFERENCE BOOK
TS U 23.2-30802090-020:2002
TS U 23.2-30802090-042:2005
142
TECHNOLOGICAL COOLING LUBRICANTS
144
REFERENCE BOOK
REFERENCE BOOK
AUTO CHEMISTRY
AUTO CHEMISTRY
145
REFERENCE BOOK
146
Cooling liquids
REFERENCE BOOK
TS U 24.6-30802090-130:2009
147
Cooling liquids
REFERENCE BOOK
TS U 24.6-30802090-130:2009
148
Windshield fluids
REFERENCE BOOK
TS U 24.5-36451680-158:2010
Crystal windshield fluids can be used for cleaning the glass, headlights and
mirrors from ice, mud and insects; as well as a glass anti-fog. Fluids can be used
in all seasons, manually or with use of the washer.
Crystal windshield fluids can be used domestically for cleaning glass, mirrors,
crystal items, porcelain, pottery and ceramics (excluding food dishes).
Depending on operating conditions and the temperature of crystallization
several brands of liquids are offered: Crystal-2; Crystal-5; Crystal-16; Crystal-20;
Crystal-25; Crystal-32; Crystal-50
Crystal
Index name
2 5 16 20 25 32 50
Appearance at the
temperature of Homogenous transparent liquid without mechanical impurities
(20 ± 5) °С
Density at 20°С, 900- 900- 850- 850- 850- 850- 850-
kg / m3, within 1000 1000 980 980 980 980 980
Crystallization
temperature, °С, not -2 -5 -16 -20 -25 -32 -50
more than
РН level, рН units,
6-9 6-9 6-9 6-9 6-9 6-9 6-9
within
149
AUTO CHEMISTRY Windshield fluids
150
REFERENCE BOOK
Windshield fluids
Metal packing
REFERENCE BOOK
Metal packing
METAL PACKING
151
Metal packing
REFERENCE BOOK
152
Metal packing
REFERENCE BOOK
153
Metal packing
REFERENCE BOOK
154
Correspondence table products
REFERENCE BOOK
CASTROL MS / 3 Grease
NUCO Grease 57; SHELL Alvania RL 2; Q8
Agrinol 158
Li-K 1/2 Rubens WB 2; NESTE Semilix 1,5 / Superlix EP2;
Agrinol 158М
ELF Epexelf 1,2; ZIC Wheel Bearing Grease 2
Agrinol ShRB-4 к-Ва 2 Cluber Lubrication Centoplex 132 BV
Multu-purpose lubricants
Agrinol Fiol 1 Li 1 BP Energrease L 1, 2; MOBIL Mobilux 1,2; SHELL
Alvania RL 1,2
Agrinol Fiol 2 Li 2 CASTROL LM Grease; TEBOIL Multi-Purpose
Grease 2
155
Correspondence table products
REFERENCE BOOK
156
Correspondence table products
REFERENCE BOOK
157
Correspondence table products
REFERENCE BOOK
158
Correspondence table products
REFERENCE BOOK
159
Correspondence table products
REFERENCE BOOK
160
Annex
REFERENCE BOOK
In agreement with the customer the lubrication may be shipped in other types of packing
designed to transport plastic products. Annex
161
Index
REFERENCE BOOK
162
Index
REFERENCE BOOK
163
Index
REFERENCE BOOK
164
Index
REFERENCE BOOK
TSp-10 .................................................................33
TSp-14gip ...........................................................33
165
Notes
REFERENCE BOOK
Notes
166
Notes
REFERENCE BOOK
Notes
167
Notes
REFERENCE BOOK
Notes
168