Professional Documents
Culture Documents
8-channel multiplexer
Description
The M74HC151 is a high-speed CMOS
8-channel multiplexer manufactured using silicon
2
gate C MOS technology.
SO16 TSSOP16
It provides, in one device, the ability to select one
bit of data from up to eight sources. The
M74HC151 can be used as a universal function
Features generator to generate any logic function of four
variables. Outputs Y and W are complementary;
• High speed: tPD = 17 ns (typ.) at VCC = 6 V the selection depends on the address inputs A,
• Low power dissipation: B, and C. The strobe input must be taken low to
ICC = 4 µA (max.) at TA = 25 °C enable this device. When the strobe is high, the
• High noise immunity: W output is forced high and consequently the Y
VNIH = VNIL = 28 % VCC (min.) output goes low. All inputs are equipped with
• Symmetrical output impedance: protection circuits to guard against static
|IOH| = IOL = 4 mA (min) discharge and transient excess voltage.
• Balanced propagation delays: tPLH ~= tPHL
• Wide operating voltage range:
VCC (OPR) = 2 V to 6 V Table 1: Device summary
• Pin and function compatible with Temperature
74 series 151 Order code Package Packaging Marking
range
• ESD performance
− CDM: 1 kV SO16
(1) -40 °C to Tape and
M74HC151YRM13TR (automotive 74HC151Y
− HBM: 2 kV +125 °C
grade)
1 reel
− MM: 200 V
-55 °C to Tape and
M74HC151RM13TR SO16 74HC151
+125 °C reel
-55 °C to Tape and
M74HC151TTR TSSOP16 HC151
+125 °C reel
TSSOP16
1 -40 °C to Tape and
M74HC151YTTR (automotive HC151Y
+125 °C 1 reel
grade)
Notes:
(1)
Qualification and characterization according to AEC Q100 and Q003 or equivalent,
advanced screening according to AEC Q001 and Q002 or equivalent.
1 Pin information
Figure 1: Pin connections and IEC logic symbols
2 Functional description
Inputs Outputs
Select STROBE
Y W
C B A S
(1) 1 1
X X X H L H
L L L L D0 D 0
L L H L D1 D 1
L H L L D2 D 2
L H H L D3 D 3
H L L L D4 D 4
H L H L D5 D 5
H H L L D6 D 6
H H H L D7 D 7
Notes:
(1)
X: don’t care
This logic diagram has not been used to estimate propagation delays.
3 Electrical characteristics
Stressing the device above the ratings listed in the "Absolute maximum ratings" table may
cause permanent damage to the device. These are stress ratings only, and operation of the
device at these or any other conditions above those indicated in the operating sections of
this specification are not implied. Exposure to absolute maximum rating conditions for
extended periods may affect device reliability.
Notes:
(1)
500 mW at 65 °C; derate to 300 mW by 10 mW/°C from 65 °C to 85 °C
Table 6: DC specifications
Value
Test condition
Symbol Parameter TA = 25°C -40 to 85°C -55 to 125°C Unit
VCC (V) Min. Typ. Max. Min. Max. Min. Max.
2.0 30 75 95 110
tTLH tTHL Output transition time 4.5 8 15 19 22 ns
6.0 7 13 16 19
2.0 56 130 165 190
tPLH tPHL Propagation delay time (D – W) 4.5 16 26 33 38 ns
6.0 14 22 28 32
2.0 56 130 165 190
Propagation delay time (D – Y)
tPLH tPHL 4.5 16 26 33 38 ns
6.0 14 22 28 32
Propagation delay time 2.0 30 85 105 125
tPLH tPHL ( STROBE – W) 4.5 10 17 21 25 ns
6.0 9 14 18 21
2.0 30 85 105 125
tPLH tPHL Propagation delay time
4.5 10 17 21 25 ns
( STROBE – Y)
6.0 9 14 18 21
2.0 72 160 200 235
tPLH tPHL Propagation delay time 4.5 20 32 40 47 ns
(A, B, C – W)
6.0 17 27 34 40
Test Value
Symbol Parameter condition TA = 25°C -40 to 85°C -55 to 125°C Unit
VCC (V) Min. Typ. Max. Min. Max. Min. Max.
Input
CIN 5.0 5 10 10 10 pF
capacitance
Power
CPD dissipation 5.0 63 pF
(1)
capacitance
Notes:
(1)
CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the
operating current consumption without load (refer to the test circuit). The average operating current
can be obtained by the following equation: ICC(opr) = CPD x VCC x fIN + ICC
V CC
PULSE
GENERATOR D.U.T.
2
1 CL
RT
4 Package information
In order to meet environmental requirements, ST offers these devices in different grades of
® ®
ECOPACK packages, depending on their level of environmental compliance. ECOPACK
specifications, grade definitions and product status are available at: www.st.com.
®
ECOPACK is an ST trademark.
PO13H
mm. inches
Dimensions Min. Typ. Max. Min. Typ. Max.
A 1.75 0.068
a1 0.1 0.2 0.003 0.007
a2 1.65 0.064
b 0.35 0.46 0.013 0.018
b1 0.19 0.25 0.007 0.010
C 0.5 0.019
c1 45 ° (typ.)
D 9.8 10 0.385 0.393
E 5.8 6.2 0.228 0.244
e 1.27 0.050
e3 8.89 0.350
F 3.8 4.0 0.149 0.157
G 4.6 5.3 0.181 0.208
L 0.5 1.27 0.019 0.050
M 0.62 0.024
S 8 ° (max.)
A A2
K L
A1 b e c E
E1
mm. inches
Dimensions Min. Typ. Max. Min. Typ. Max.
A 1.2 0.047
A1 0.05 0.15 0.002 0.004 0.006
A2 0.8 1 1.05 0.031 0.039 0.041
b 0.19 0.30 0.007 0.012
c 0.09 0.20 0.004 0.0089
D 4.9 5 5.1 0.193 0.197 0.201
E 6.2 6.4 6.6 0.244 0.252 0.260
E1 4.3 4.4 4.48 0.169 0.173 0.176
e 0.65 BSC 0.0256 BSC
K 0° 8° 0° 8°
L 0.45 0.60 0.75 0.018 0.024 0.030
5 Revision history