Professional Documents
Culture Documents
A3 Manual PDF
A3 Manual PDF
Advice
This User’s Guide defines both the establishment and
termination of right and liability with respect to product
quality guarantee responsibility and after-sales service
between Chery Automobile Co., Ltd. and customers. It
is necessary for customers to carefully read over this
manual before using Chery’s products.
Truly congratulate you on having a Chery A3 car! Also, sincerely thank you for your preference towards Chery and Chery’s products!
All staff of Chery authorized service stations have experienced the good and professional training, and they provide you with the best service heart and soul.
The advanced technology and the preeminent performance are incorporated into Chery A3 Series cars. Your selecting a Chery A3 car indicates that you have
rather rigorous requirements on the performance and style of a car.
This User’s Guide is intended to introduce technical characteristics, use methods and relevant precautions of Chery A3 Series cars.
You should carefully read over this User’s Guide, so that you may get familiar with characteristics of the car, properly use and maintain your car, take full
advantage of the outstanding performance of car, ensure the security of driving, keep the excellent performance of car, and finally obtain the maximized joy of
driving.
1
Preface
This manual is compiled in accordance with the If the any problem is found in Chery’s product
road conditions in People’s Republic of China and
Special Statements during the course of use, the car shall be checked
the specific conditions of Chery A3 Series cars, so and repaired by Chery authorized service station.
Before using this product, you should carefully
that it is only applicable to the A3 Series cars which In the process of check and repair, the station,
read over this User’s Guide, especially the section
is manufactured by Chery Automobile Co., Ltd. considering the actual conditions, is entitled to
“Quality Guarantee Service”, lest you may lose
and runs in the territory of People’s Republic of decide whether to carry out maintenance by
the right of enjoying the quality guarantee service
China. It includes the latest information till the means of repairing or replacing the equivalent. If
provided by Chery due to your violation against the
printing of this manual. Chery Automobile Co., Ltd. you meet something unclear when reading the
use compliance.
takes the full responsibility for revising and User’s Guide, you can get further interpretation
interpreting this manual, and also reserves the Chery Automobile Co., Ltd. (hereinafter referred to from Chery authorized service station. At the same
right that Chery may not give the further as “the Company” or “Chery”) has set the time, customer’s opinion and suggestion are
notification in the case of changing products after running-in rules for new cars and the technical considered precious and welcome.
the printing of this manual. Some figures in this maintenance for various stages, including the
The copyright of this manual is reserved by Chery
manual are featured and only used for reference. If first-time 5,000km maintenance. As the
Automobile Co., Ltd.
the featured car differs from the actual car, the maintenance rules forementioned is crucial to the
latter shall prevail. safe use and good running status of your car, you May you enjoy the driving!
shall abide by them.
This manual is the major voucher by which you
may get the vehicle quality guarantee and the If your car comes into failure as a result of your
first-time free maintain for your car. Please put this abuse, neglect and misuse of car or parts, or not
manual in your car, so as to find it whenever you having maintenance according to the required
need it. If you are going to resell the car, please mileage or time interval, or not having signed the
hand over this manual and the complete set of maintenance certification as required, or the
attached files together with the car to the new unapproved refitment or addition to your car, you
owner in order to allow for his use when necessary. will lose the right of claiming guarantee, and the
consequential direct or indirect guarantee
application shall be rejected by Chery authorized
service stations.
2
Catalogues
3
Drive Introduction
Chapter 1 Introduction
4
Drive Introduction
5
Drive Introduction
6
Drive Introduction
When the car is running, the too low engine speed replaced or whose wheel nuts have been
is also undesired. It is necessary to shift the lever loosened, it is also required to retighten these
to the proper gear, as the case may be. wheel nuts to the specified torques as soon as the
car has run for 800km.
Given a cold car, do not have the engine working
at the maximum speed, despite the lever being set
in the neutral or a driving gear.
“One-to-one” Service
At beginning of use, a new tyre does not get the For the purpose of providing you with the better
best adhesive force. Therefore, even a new tyre service and car, the dealer under Chery will assign
also needs running-in. Consequently, during the a service consultant for you when you are buying a
first 100km, the car speed shall be kept low and Chery car. If you have any question during the
the driving shall be particularly careful. course of using the car, you can contact your
service consultant and he/she will present the best
A new brake friction wafer wants running-in as
service to you.
well, for the brake does not have the ideal friction
within the first 200km. If the braking effect during
such a period seems poor, it is allowed to properly
increase the pressure on the pedal. This method is
also applicable every time you henceforth replace
the friction wafers with new ones.
7
Drive Introduction
Date of Delivery:
8
Drive Introduction
Car Data
Date of Delivery
Official Seal of
Dealer
Car Type
Engine No.
Transmission No.
9
Drive Introduction
Chery Car Sale & Delivery Sheet
1 Engine Yes □ No □
2 Engine oil, brake fluid, steering fluid, coolant, battery fluid and windscreen detergent Yes □ No □
Lights of complete car, including: headlight, turn light, fog light, combination light, indoor light, brake
5 Yes □ No □
light, reversing light, taillight, reading light, door light, instrument light and so on
7 Tachometer, engine speedometer, odometer, water thermometer and fuel meter Yes □ No □
8 Wheel shields, spare tyre, attached tools and User’s Guide of Complete Car Yes □ No □
9 Safety belt, seat, cigarette lighter, air conditioner switch, air outlet, glove box and sun visor Yes □ No □
10 Glass regulator, rearview mirror, windscreen wiper, scrubber, horn, audio system and antenna Yes □ No □
10
Drive Introduction
11
Drive Introduction
12
Drive Introduction
Kept by Customer
of maintenance have been introduced. □ Other affairs required by customer
□ The importance of maintaining/repairing car in Chery authorized service IV. Establishment of “One-to-one” Consultative Service Relation
station has been informed.
□ The User’s Guide has been delivered and I have been reminded of
reading.
□ The functions and use methods of Chery customer service hot line have Business Card of Service
been told. Consultant
II. Introduction to “One-to-one” Consultative Service Model (√ for yes, × for
no)
□ If you have some questions or requirements, you just need to inquire
nobody but your service consultant. Signature of Customer/ Date:
□ The service consultant is the only person that is designated by the service Signature of Service Consultant/ Date:
station to communicate with his customer.
13
Drive Introduction
14
Drive Introduction
15
Drive Introduction
Airbag mark
Indoor switch
Unlocking indication
indication
Electric Power
Warning light Steering (EPS)
indicating unclosed Audio alarming
door and luggage boot
lid
Anti-theft indication of
ESP indication
engine
16
Drive Introduction
17
Drive Introduction
Safety Precautions ● Turn the ignition switch to the “ON” potion, and don’t
Long-time running of engine at high speed will cause switch it to the position “START”.
excessively high temperature of the engine and exhaust The idle speed of engine is controlled by electronic control If it is hard to turn the key, you can rotate the steering wheel
system, which will possibly result in fire and other system. The high idle speed as the engine starting makes left and right for several times until the key can be turned
damages. Therefore, don’t park the vehicle on the ground for the temperature rise of engine. After the temperature easily. Reasons causing this situation are listed as follows:
with dry grass or other dry coverings. rise, the idle speed should be reduced automatically. If the ● Deflection of the front wheel.
idle speed can’t be reduced automatically, the vehicle ● The front wheel touches curb.
should be sent to Chery authorized service station for ● The steering wheel has been rotated as getting on or off
overhaul. Don’t let the engine operate for over 10 minutes the vehicle (viz. the steering wheel is self-locked).
at the speed higher than the specified idle speed.
18
Drive Introduction
19
Drive Introduction
20
Drive Introduction
21
Drive Introduction
22
Drive Introduction
Make Use of ABS Brake In the same way, the use of ABS can’t avoid the dangers
caused by short distance to the front vehicle, traveling in
Step on the brake pedal with all effort continuously in water, too fast steering or poor road condition; it can’t avoid Important principle to
emergency, and the antilock brake system will be started the accidents caused by mistake as well as the incorrect use ABS brake
immediately so that you are still able to control the steering. driving either. Please be cautious of driving and reduce the
If the space is enough, you can even avoid obstructions. speed as turning.
23
Drive Introduction
Hand Brake If you want to release the hand brake, you can pull Application/operation methods and precautions:
the hand brake handle upward a little, press the
release button on the top of handle and then push ● Step on the clutch pedal completely as shifting
it downwards. in order to make the transmission input shaft
separated with engine power, and then
The manual brake works on the rear wheels. operate the shift lever to shift.
Stepping on the brake pedal while pulling the
manual brake upwards can make the hand brake ● The low gear shall be applied as going
pulled easily. downhill or turning, and It is forbidden to make
the vehicle slide with the clutch separated.
Operation of Manual Transmission
● When the transmission is shifting up, don’t
The hand brake handle should be pulled upward
The order of gears is shown in the following figure: skip over gears, or else it will affect the service
tightly to avoid the vehicle sliding for oversight.
life of the synchronizer.
● Flapping method (that is the operation method
Please be sure to pull up the hand brake handle of pushing followed by releasing) is forbidden
before leaving the vehicle. as shifting. The shift gear shall be pressed
with hand all the time, which can reduce the
In the condition that the ignition switch is on, pull the hand
brake handle, and the parking braking indicator lamp will wearing time of the lock ring of synchronizer
light. If you want to use the hand brake, pull the hand brake and reduce the abrasion.
handle upward.
● Don’t put your hand on the shift lever as
traveling, or else it will cause too early
abrasion of shift fork.
● IF there are abnormal phenomena of
transmission in use such as abnormal sound
and obviously difficult operation, stop the
vehicle at once to for check and continue to
24
Drive Introduction
25
Drive Introduction
If the water goes into the air intake pipe of engine, Driving the Vehicle Equipped with
it will cause serious damage to the engine. If
wading deeply, the water entering the transmission
Unleaded Gasoline Catalytic Converter
through air vent of transmission, it will damage the
transmission.
During traveling, if the engine ignites badly
After wading, you must drive the vehicle slowly and or the performance reduces, please drive at low
step on the brake pedal lightly for several times to speed to the nearest Chery authorized service
remove the water on the brake. station.
The vehicle with gasoline engine is equipped
Three-way Catalytic Converter with narrow fuel filler, which only admits the filling Please avoid all the cases that can cause the
gun nozzle of the unleaded petrol pump. unburned or partly burnt fuel to enter the catalytic
The three-way catalytic converter contributes to converter, especially when the engine is of high
reducing the waste air pollution. temperature.
If the engine is operating all the while, the Always avoid the following cases:
three-way catalytic converter will become very hot.
Be sure to sue the unleaded fuel. The Be sure to wear protective gloves during ● Fuel exhaustion.
leaded fuel will cause permanent damage to the maintenance to avoid scald.
three-way catalytic converter and oxygen sensor. ● Unnecessary long-time starting of the engine.
Chery Company will not bear any responsibility for
the damage resulted by using leaded fuel. This ● The engine operates in the condition that
kind of damage is out of the warranty scope. If you When the gasoline engine operates, it is more than one spark plugs are removed.
add the leaded fuel inadvertently, please contact forbidden to pull out the ignition cable of the ● Start the vehicle with the engine at operating
the nearest Chery authorized service station ignition coil and check whether the engine works temperature through pushing or drawing.
immediately. well with individual cylinder cut-off method, or else
it will damage the three-way catalytic converter.
26
Drive Introduction
● Turn off the ignition switch during traveling. Oil Consumption Regular cold-start and shot-range travel will result
in obvious increase of the oil consumption.
Parking Oil consumption is influenced by the
● Traffic and road conditions
Don’t park on the ground with dry leaves or grass. following factors:
Even if the engine has been stalled, there is a Traffic jam, uphill driving, lots of curves and
● The selection of speed & gear rough road all affect the oil consumption.
potential fire hazard because the exhaust pipe still
emits much heat in short time. ●
Oil consumption
Good driving habit
Before leaving the vehicle, the ignition switch must Foresee the danger and keep safety distance
be turned off. Don’t let the engine operate when from the front vehicles, which not only can
nobody in the vehicle. If this point is neglected, decrease oil consumption but reduce the braking
your vehicle is likely to move unexpectedly, abrasion and noise.
resulting in personal injury or property damage.
Speed ● Vehicle loaded condition
Chassis Protection
Increase the load of vehicle will cause higher oil
Your vehicle has been quipped with thermal baffle. consumption.
Don’t hold painting work on the thermal baffle, The above figure shows how the oil consumption is
exhaust pipe or the catalytic converter body or influenced by the selection of speed and gear. ● Vehicle technical condition
beside them. Please don’t remove the thermal Operating at low gear to improve the acceleration
performance will result in the obvious higher oil Too low tyre pressure or the improper maintenance
baffle.
consumption. of engine & vehicle will result in high oil
consumption.
● Stroke / engine temperature
27
Drive Introduction
28
Drive Introduction
29
Drive Introduction
Safety Precautions ● Turn the ignition switch to the “ON” potion, and don’t
Long-time running of engine at high speed will cause switch it to the position “START”.
excessively high temperature of the engine and exhaust The idle speed of engine is controlled by electronic control If it is hard to turn the key, you can rotate the steering wheel
system, which will possibly result in fire and other system. The high idle speed as the engine starting makes left and right for several times until the key can be turned
damages. Therefore, don’t park the vehicle on the ground for the temperature rise of engine. After the temperature easily. Reasons causing this situation are listed as follows:
with dry grass or other dry coverings. rise, the idle speed should be reduced automatically. If the ● Deflection of the front wheel.
idle speed can’t be reduced automatically, the vehicle ● The front wheel touches curb.
should be sent to Chery authorized service station for ● The steering wheel has been rotated as getting on or off
overhaul. Don’t let the engine operate for over 10 minutes the vehicle (viz. the steering wheel is self-locked).
at the speed higher than the specified idle speed.
30
Drive Introduction
31
Drive Introduction
32
Drive Introduction
33
Drive Introduction
34
Drive Introduction
Make Use of ABS Brake In the same way, the use of ABS can’t avoid the dangers
caused by short distance to the front vehicle, traveling in
Step on the brake pedal with all effort continuously in water, too fast steering or poor road condition; it can’t avoid Important principle to
emergency, and the antilock brake system will be started the accidents caused by mistake as well as the incorrect use ABS brake
immediately so that you are still able to control the steering. driving either. Please be cautious of driving and reduce the
If the space is enough, you can even avoid obstructions. speed as turning.
35
Drive Introduction
Hand Brake If you want to release the hand brake, you can pull Application/operation methods and precautions:
the hand brake handle upward a little, press the
release button on the top of handle and then push ● Step on the clutch pedal completely as shifting
it downwards. in order to make the transmission input shaft
separated with engine power, and then
The manual brake works on the rear wheels. operate the shift lever to shift.
Stepping on the brake pedal while pulling the
manual brake upwards can make the hand brake ● The low gear shall be applied as going
pulled easily. downhill or turning, and It is forbidden to make
the vehicle slide with the clutch separated.
Operation of Manual Transmission
● When the transmission is shifting up, don’t
The hand brake handle should be pulled upward
The order of gears is shown in the following figure: skip over gears, or else it will affect the service
tightly to avoid the vehicle sliding for oversight.
life of the synchronizer.
● Flapping method (that is the operation method
Please be sure to pull up the hand brake handle of pushing followed by releasing) is forbidden
before leaving the vehicle. as shifting. The shift gear shall be pressed
with hand all the time, which can reduce the
In the condition that the ignition switch is on, pull the hand
brake handle, and the parking braking indicator lamp will wearing time of the lock ring of synchronizer
light. If you want to use the hand brake, pull the hand brake and reduce the abrasion.
handle upward.
● Don’t put your hand on the shift lever as
traveling, or else it will cause too early
abrasion of shift fork.
● IF there are abnormal phenomena of
transmission in use such as abnormal sound
and obviously difficult operation, stop the
vehicle at once to for check and continue to
36
Drive Introduction
37
Drive Introduction
If the water goes into the air intake pipe of engine, Driving the Vehicle Equipped with
it will cause serious damage to the engine. If
wading deeply, the water entering the transmission
Unleaded Gasoline Catalytic Converter
through air vent of transmission, it will damage the
transmission.
During traveling, if the engine ignites badly
After wading, you must drive the vehicle slowly and or the performance reduces, please drive at low
step on the brake pedal lightly for several times to speed to the nearest Chery authorized service
remove the water on the brake. station.
The vehicle with gasoline engine is equipped
Three-way Catalytic Converter with narrow fuel filler, which only admits the filling Please avoid all the cases that can cause the
gun nozzle of the unleaded petrol pump. unburned or partly burnt fuel to enter the catalytic
The three-way catalytic converter contributes to converter, especially when the engine is of high
reducing the waste air pollution. temperature.
If the engine is operating all the while, the Always avoid the following cases:
three-way catalytic converter will become very hot.
Be sure to sue the unleaded fuel. The Be sure to wear protective gloves during ● Fuel exhaustion.
leaded fuel will cause permanent damage to the maintenance to avoid scald.
three-way catalytic converter and oxygen sensor. ● Unnecessary long-time starting of the engine.
Chery Company will not bear any responsibility for
the damage resulted by using leaded fuel. This ● The engine operates in the condition that
kind of damage is out of the warranty scope. If you When the gasoline engine operates, it is more than one spark plugs are removed.
add the leaded fuel inadvertently, please contact forbidden to pull out the ignition cable of the ● Start the vehicle with the engine at operating
the nearest Chery authorized service station ignition coil and check whether the engine works temperature through pushing or drawing.
immediately. well with individual cylinder cut-off method, or else
it will damage the three-way catalytic converter.
38
Drive Introduction
● Turn off the ignition switch during traveling. Oil Consumption Regular cold-start and shot-range travel will result
in obvious increase of the oil consumption.
Parking Oil consumption is influenced by the
● Traffic and road conditions
Don’t park on the ground with dry leaves or grass. following factors:
Even if the engine has been stalled, there is a Traffic jam, uphill driving, lots of curves and
● The selection of speed & gear rough road all affect the oil consumption.
potential fire hazard because the exhaust pipe still
emits much heat in short time. ●
Oil consumption
Good driving habit
Before leaving the vehicle, the ignition switch must Foresee the danger and keep safety distance
be turned off. Don’t let the engine operate when from the front vehicles, which not only can
nobody in the vehicle. If this point is neglected, decrease oil consumption but reduce the braking
your vehicle is likely to move unexpectedly, abrasion and noise.
resulting in personal injury or property damage.
Speed ● Vehicle loaded condition
Chassis Protection
Increase the load of vehicle will cause higher oil
Your vehicle has been quipped with thermal baffle. consumption.
Don’t hold painting work on the thermal baffle, The above figure shows how the oil consumption is
exhaust pipe or the catalytic converter body or influenced by the selection of speed and gear. ● Vehicle technical condition
beside them. Please don’t remove the thermal Operating at low gear to improve the acceleration
performance will result in the obvious higher oil Too low tyre pressure or the improper maintenance
baffle.
consumption. of engine & vehicle will result in high oil
consumption.
● Stroke / engine temperature
39
Drive Introduction
40
Drive Introduction
41
Deal With Emergencies
Safety Precautions ● Turn the ignition switch to the “ON” potion, and don’t
Long-time running of engine at high speed will cause switch it to the position “START”.
excessively high temperature of the engine and exhaust The idle speed of engine is controlled by electronic control If it is hard to turn the key, you can rotate the steering wheel
system, which will possibly result in fire and other system. The high idle speed as the engine starting makes left and right for several times until the key can be turned
damages. Therefore, don’t park the vehicle on the ground for the temperature rise of engine. After the temperature easily. Reasons causing this situation are listed as follows:
with dry grass or other dry coverings. rise, the idle speed should be reduced automatically. If the ● Deflection of the front wheel.
idle speed can’t be reduced automatically, the vehicle ● The front wheel touches curb.
should be sent to Chery authorized service station for ● The steering wheel has been rotated as getting on or off
overhaul. Don’t let the engine operate for over 10 minutes the vehicle (viz. the steering wheel is self-locked).
at the speed higher than the specified idle speed.
42
Deal With Emergencies
43
Deal With Emergencies
44
Deal With Emergencies
45
Deal With Emergencies
46
Deal With Emergencies
Make Use of ABS Brake In the same way, the use of ABS can’t avoid the dangers
caused by short distance to the front vehicle, traveling in
Step on the brake pedal with all effort continuously in water, too fast steering or poor road condition; it can’t avoid Important principle to
emergency, and the antilock brake system will be started the accidents caused by mistake as well as the incorrect use ABS brake
immediately so that you are still able to control the steering. driving either. Please be cautious of driving and reduce the
If the space is enough, you can even avoid obstructions. speed as turning.
47
Deal With Emergencies
Hand Brake If you want to release the hand brake, you can pull Application/operation methods and precautions:
the hand brake handle upward a little, press the
release button on the top of handle and then push ● Step on the clutch pedal completely as shifting
it downwards. in order to make the transmission input shaft
separated with engine power, and then
The manual brake works on the rear wheels. operate the shift lever to shift.
Stepping on the brake pedal while pulling the
manual brake upwards can make the hand brake ● The low gear shall be applied as going
pulled easily. downhill or turning, and It is forbidden to make
the vehicle slide with the clutch separated.
Operation of Manual Transmission
● When the transmission is shifting up, don’t
The hand brake handle should be pulled upward
The order of gears is shown in the following figure: skip over gears, or else it will affect the service
tightly to avoid the vehicle sliding for oversight.
life of the synchronizer.
● Flapping method (that is the operation method
Please be sure to pull up the hand brake handle of pushing followed by releasing) is forbidden
before leaving the vehicle. as shifting. The shift gear shall be pressed
with hand all the time, which can reduce the
In the condition that the ignition switch is on, pull the hand
brake handle, and the parking braking indicator lamp will wearing time of the lock ring of synchronizer
light. If you want to use the hand brake, pull the hand brake and reduce the abrasion.
handle upward.
● Don’t put your hand on the shift lever as
traveling, or else it will cause too early
abrasion of shift fork.
● IF there are abnormal phenomena of
transmission in use such as abnormal sound
and obviously difficult operation, stop the
vehicle at once to for check and continue to
48
Deal With Emergencies
49
Deal With Emergencies
If the water goes into the air intake pipe of engine, Driving the Vehicle Equipped with
it will cause serious damage to the engine. If
wading deeply, the water entering the transmission
Unleaded Gasoline Catalytic Converter
through air vent of transmission, it will damage the
transmission.
During traveling, if the engine ignites badly
After wading, you must drive the vehicle slowly and or the performance reduces, please drive at low
step on the brake pedal lightly for several times to speed to the nearest Chery authorized service
remove the water on the brake. station.
The vehicle with gasoline engine is equipped
Three-way Catalytic Converter with narrow fuel filler, which only admits the filling Please avoid all the cases that can cause the
gun nozzle of the unleaded petrol pump. unburned or partly burnt fuel to enter the catalytic
The three-way catalytic converter contributes to converter, especially when the engine is of high
reducing the waste air pollution. temperature.
If the engine is operating all the while, the Always avoid the following cases:
three-way catalytic converter will become very hot.
Be sure to sue the unleaded fuel. The Be sure to wear protective gloves during ● Fuel exhaustion.
leaded fuel will cause permanent damage to the maintenance to avoid scald.
three-way catalytic converter and oxygen sensor. ● Unnecessary long-time starting of the engine.
Chery Company will not bear any responsibility for
the damage resulted by using leaded fuel. This ● The engine operates in the condition that
kind of damage is out of the warranty scope. If you When the gasoline engine operates, it is more than one spark plugs are removed.
add the leaded fuel inadvertently, please contact forbidden to pull out the ignition cable of the ● Start the vehicle with the engine at operating
the nearest Chery authorized service station ignition coil and check whether the engine works temperature through pushing or drawing.
immediately. well with individual cylinder cut-off method, or else
it will damage the three-way catalytic converter.
50
Deal With Emergencies
● Turn off the ignition switch during traveling. Oil Consumption Regular cold-start and shot-range travel will result
in obvious increase of the oil consumption.
Parking Oil consumption is influenced by the
● Traffic and road conditions
Don’t park on the ground with dry leaves or grass. following factors:
Even if the engine has been stalled, there is a Traffic jam, uphill driving, lots of curves and
● The selection of speed & gear rough road all affect the oil consumption.
potential fire hazard because the exhaust pipe still
emits much heat in short time. ●
Oil consumption
Good driving habit
Before leaving the vehicle, the ignition switch must Foresee the danger and keep safety distance
be turned off. Don’t let the engine operate when from the front vehicles, which not only can
nobody in the vehicle. If this point is neglected, decrease oil consumption but reduce the braking
your vehicle is likely to move unexpectedly, abrasion and noise.
resulting in personal injury or property damage.
Speed ● Vehicle loaded condition
Chassis Protection
Increase the load of vehicle will cause higher oil
Your vehicle has been quipped with thermal baffle. consumption.
Don’t hold painting work on the thermal baffle, The above figure shows how the oil consumption is
exhaust pipe or the catalytic converter body or influenced by the selection of speed and gear. ● Vehicle technical condition
beside them. Please don’t remove the thermal Operating at low gear to improve the acceleration
performance will result in the obvious higher oil Too low tyre pressure or the improper maintenance
baffle.
consumption. of engine & vehicle will result in high oil
consumption.
● Stroke / engine temperature
51
Deal With Emergencies
52
Deal With Emergencies
53
54
Parameters of Capacity and Specifications
55
Parameters of Capacity and Specifications
56
Parameters of Capacity and Specifications
57
Parameters of Capacity and Specifications
Your vehicle is equipped with the fuse extractor, The instrument electric box is located in the left
which can be found in the fuse box of the engine side of instrument panel. Open the protective cover
Spare Tyre
compartment. of the electric box and the instrument electric box
The spare tyre is located under the carpet in the
can be seen. Then check or replace the fuses.
luggage boot.
Engine Compartment Electric Box
Replacing Wheel
Procedure for Replacing Spare
Tyre
Before jacking up the vehicle, make
sure to observe the following precautions. The spare tyre is located under the carpet in the
luggage boot. Open the luggage boot, loosen the
1. Park your vehicle in a proper place and make nuts securing the spare tyre anticlockwise by hand
sure that the replacement of tyres will not and take out the spare tyre.
affect the traffic or endanger yourself.
On-vehicle Jack
The jack-up position of the rear wheels is the part 4. If necessary, use a proper wheel block stop to
Jack-up Position filled in black in the figure. secure the vehicle and prevent it from rolling
or sliding.
The jack can only be rested in specific positions
under the car as shown in the figure. The groove 5. Use special tools on the vehicle to loosen the
part of the jack shall be rested on the raised part of wheel bolts as shown in the following figure.
the bottom of the vehicle, as near as possible to
the wheel to be repaired.
59
Parameters of Capacity and Specifications
Safety Advices
3. Lower the vehicle to remove the jack. While handling the battery, make sure
6. Place the jack so that the whole foot seat
to take the following precaution measures.
surface is located on a firm ground. 4. Replace the jack and the faulty wheel, and
secure them.
7. The jack shall be jacked up vertically to the
jack-up point. 5. If possible, deliver the wheel to Chery
authorized service station to check the
8. Jack up the vehicle until the wheel is above
tightening torque of the wheel bolt and the tyre
the ground.
pressure.
9. Loosen the wheel bolts to remove the wheel.
6. Since the spare tyre may be in storage for a ● The acid liquid of the battery is corrosive. Be
long time, its tyre shall be inflated with a sure to wear gloves and goggles. Do not allow
Mount Wheel pressure slightly higher than that of the your skin or clothing to come in contact with
normally used tyre to ensure that the spare acid or lead. Do not tilt the battery, for the acid
1. Push the wheel onto the wheel hub bearing to
tyre has standard pressure in it. liquid may flow from the vent opening. If the
align it with the bolt hole, screw on the wheel
acid liquid splashes into your eyes, wash your
bolt clockwise and make sure the pointed end
eyes immediately with clean water for several
of the wheel nut faces the wheel.
minutes and then seek doctor’s advice. If the
acid liquid splashes onto your skin or clothing,
60
Parameters of Capacity and Specifications
neutralize it with alkaline water (soap) and 4. When re-connecting the battery, first connect
then wash your skin or clothing with clean the positive (+) cable and then the negative (-)
water. If the acid liquid is swallowed, rush to cable.
the hospital immediately.
5. If the battery is re-connected after being
The electronic ignition system has high tension. removed, the vehicle may initially show
Please do not touch the components in the system slightly abnormal performance. This indicates
when the engine is running or the ignition switch is that the control system of the engine is
on. re-adapting to the engine.
● Keep children away from the acid liquid of the
battery. Removal and Installation
62
Parameters of Capacity and Specifications
3. Before disconnecting the leads, run the The rear trailer ring is located in the right mid-and- Note: The bolt thread is screwed in
engines of the two vehicles for three minutes. lower position of the rear bumper. Its mounting is anticlockwise.
the same as that of the front trailer ring. During the
Disconnect Lead trailing, drive the trailer slowly and smoothly to
prevent the trailer and the trailed vehicle from
First disconnect lead B (-) and then lead A (+). bouncing. If the pulling force of the trailing cable is During the trailing, the ignition switch of
too big, the vehicle may be damaged. the trailed vehicle shall be in the “ON” position
so that the steering wheel, the turn lamp and the
To reduce the voltage surge during the brake lamp can all work. Since the engine is
disconnection, please connect the blower and turned off, there is nor the braking or steering
the electric-heated rear windshield of the vehicle forces, so greater operating force is needed.
with the low battery. Please do not turn on the Therefore, the braking and steering forces shall
headlamps in stead of the heated rear windshield, be increased accordingly.
for the surge voltage may burn and damage the
bulbs.
Breakdown Trailer
The vehicle is equipped with threaded holes for The front trailer ring is located
trailer rings at both the front and the rear. In the between the left headlamp and
the left front fog lamp.
actual use, pry up the decorative cover with a flat
tip screwdriver, and then pick the trailer ring from
the on-vehicle tools and mount it into the threaded
hole for the installation of the trailing cable.
63
Parameters of Capacity and Specifications
Chapter 6 Maintenance
64
Parameters of Capacity and Specifications
The regular maintenance for your vehicle is Services Provided for You by Chery
Items You Must Implement
essential during the course of driving. Service Station
Please strictly conduct the maintenance Only the original parts and materials can Regularly inspect the liquid level and add
according to the maintenance schedule of guarantee the normal service life of your the oil liquid. Check the tyre pressure,
the manual to guarantee your vehicle's best vehicle. Please pay special attention to this: the lamps and the brakes. Check the
performance and good running state and Chery Automobile Co., Ltd. only provide the warning lamps. (See the Regular
extend the service life of vehicle. Carrying original parts to the special service stations Maintenance Schedule below for
out the regular maintenance for the vehicle of Chery all over the country, so you can reference).
can also help you to discover and eliminate only get the original parts from special
Containers of brake fluid, coolant and
the hidden dangers and prevent the service stations of Chery.
power steering fluid are semitransparent
accidents timely. This chapter describes the
Special service stations of Chery are the to facilitate the quick visual
detailed routine maintenance and inspection
only professional repair points inspection. .
methods, so that please read it carefully.
authorized by Chery Automobile Co., Ltd.
Maintenance
and their staff have been strictly trained
Maintenance is divided into two categories:
by Chery Automobile Co., Ltd. These staff
one is routine maintenance which can be Because of the high voltage inside
will be sincere to provide you with the
completed by vehicle owners, and the other
highest quality after-sales service. If the electronic ignition system, do not
is regular maintenance, inspection and
you are not satisfied with the work they touch these components when the engine
repair which should be finished by the
have done, please write directly to: is running or the ignition switch is
special service station of Chery.
After-sales Service of Sales Co., Ltd., turned on.
Please strictly use the engine oil, petrol,
Chery Automobile Co., Ltd., Economic and
antifreezing coolant and brake fluid
Technological Development Zone, Wuhu
recommended by this manual; otherwise,
City, Anhui Province, or call the Customer
your vehicle may get damaged.
Service Hotline: 400-883-8888, and we
will be in the fastest speed to eliminate
your worries. Don’t forget to write down
vehicle model, chassis code, engine code,
mileage and delivery date in your letter.
65
Parameters of Capacity and Specifications
Monthly Inspection:
The ignition switch should be turned Maintenance Schedule
off before the operation of engine
• Level of coolant level (engine in cold state)
compartment. Even if the ignition switch is
Daily Inspection:
turned off, the cooling fan may Leakage of assembly, pipeline, hose and
automatically operate all the same. • oil tank
Operating conditions of all exterior and interior
Therefore, please be careful to avoid
lamps. Replace the burned or dim bulbs and • Level of brake fluid
clothes (tie) being involved in the fan or
ensure the cleanness of all lenses.
driving belt. • Level of power steering oil
General Maintenance for Vehicle Inspection When Adding Fuel: • Operating condition of air conditioner
66
Parameters of Capacity and Specifications
67
Parameters of Capacity and Specifications
Engine Oil Dipstick In case the oil level stays between the MIN Simply rotated anticlockwise and pulled,
and the MAX signs at the lower end of the filling cover will be open. Do not open
dipstick, there is no need to add the oil the filling cover during the operation of
again. The hot engine oil may surpass the engine.
above gap sign for several millimeters due
Close the cover by rotating it clockwise
to the thermal expansion.
The engine oil consumption is affected by until hearing a click sound.
a number of factors. The new engine will In case the oil level is flush with or
reach the normal value of consumption below the MIN sign, only add the engine oil
after the vehicle has run for in line with Chery specifications to make
Do not use the engine oil
approximately 5,000km. The engine will the level stay between the MIN and the MAX
consume more oil under the high-load signs. See the chapter “Capacity and additives or engine processing agents.
operation. Specification” for details. They are not only unnecessary but in
It is necessary to carry out the regular some cases may also damage the engine,
inspection on engine oil, for example, Filling Cover for Engine Oil and this kind of damage is not within the
when adding fuel or before starting a scope of warranty.
long-distance journey.
When inspecting the engine oil, parked the
Add engine oil without
exceeding the upper limit of
reticle
69
Parameters of Capacity and Specifications
Only add the brake fluid in line with the Inspect the coolant level through the
Brake Fluid specification of Chery (see the chapter translucent reservoir. When the engine is
“Capacity and Specification”). Send it in the cold state, the coolant level
to the special service station of Chery should be between MIN and MAX signs. When
for the inspection of system leakage as the engine is hot, the coolant is likely
If the oil contacts the paint
soon as possible. to exceed the MAX sign due to the
surface, please wipe out the oil with expansion.
It is important to ensure the absolute
the wet sponge or rinse the paint
cleanness in case of adding the brake The coolant can be added if the engine is
surface with plenty of water.
fluid. cold. If it is necessary to add the coolant
in the presence of a hot engine, first of
all, wait 10 minutes to let the engine cool
down. Unscrew the cover of reservoir for
Do not let the brake fluid contact
a quart of circle to discharge the
your skin or eyes. Providing such an pressure. Wait for a period of time and
unlucky occasion is encountered, please then open the cover fully. Add the coolant
clean the affected parts with plenty of in line with the specification of this
water and immediately seek the medical vehicle.
treatment.
The brake fluid reservoir pot is located
at the left rear of engine compartment.
The oil level should stay between MAX and
Engine Coolant Tank
MIN signs at the side of oil tank. If the
oil level drops at the MIN sign, the brake
system warning light on instrument panel
Do not open the filling cover in
will lighten.
the event of a running engine or the high
temperature. Otherwise, the coolant may
eject from the system to result in the
70
Parameters of Capacity and Specifications
71
Parameters of Capacity and Specifications
Adding of Coolant
Inspection of Power Steering Fluid
The coolant is a kind of toxic 1. Unscrew the reservoir cover to add the
coolant till the MAX reticle, and run the Level
fluid and can not be used to wash hands
engine until the water temperature
or clothing. When adding the coolant, be
reaches about 90℃. It is unnecessary to
careful to avoid splash it onto any site
shut the reservoir cover, because there is
of engine. In the event that the coolant
gas discharged from pipeline, and
contact your skin or eyes, please clean
meanwhile reservoir level will drop.
the affected parts with plenty of water
and immediately seek the medical 2. Turn off the engine, add the coolant
treatment. into the reservoir and repeat the
above-mentioned processes once again
Using the coolant with correct until the reservoir level no longer drops,
concentration will not only protect the and then cover the reservoir. The fluid level should reach the MAX sign
engine from freeze in the winter, but also in case of the cold engine.
provide the anticorrosion protection
It is necessary to add the power steering
throughout the year. Modern engines
Do not mix the coolants of fluid in line with the specifications of
operate at the extremely high
Chery if the level is below the MIN sign.
temperature, so the bad coolant can not different colors and specifications.
provide the proper anticorrosion
protection for the cooling system. Transmission Oil Level
Therefore, please use the coolant in line The special service station of Chery will
with the specification of Chery. The tap inspect the level of transmission oil when
water can not be used instead. your vehicle is driven into the station
for maintenance.
See the chapter “Capacity and
Specification” for capacity.
72
Parameters of Capacity and Specifications
73
Parameters of Capacity and Specifications
The correct tyre pressure should be The worn depth of tread is limited in relevant
Replacement of Wiper Blade complied with especially during the laws and regulations. Notice that: when the
high-load and high-speed running. The worn depth reaches the limiting value of 3mm,
insufficient tyre pressure will the worn areas will appear on the tread, which
reduce the stability, increase the indicate that the performance and security of
rolling resistance and advance tyre tyre has greatly degraded and the tyre must be
abrasion and even lead to the replaced.
accident.
If you need to drive the vehicle on the
The worn tyres should be treated under
Raise the wiper arm and make it form a curb, you have to keep a low running
right angle with the wiper blade. To speed, and if possible, make the local environmental protection provisions.
remove the wiper blade, please press the wheels close to curb at right angle. Once the road conditions allow, the winter
fixing clip according to the direction Avoid the vertical and sharp tyres should be immediately changed with
shown by arrow, then release the wiper obstructions. When parking the summer ones. This will reduce the fuel
blade, and finally pull out the wiper arm vehicle, do not have the side wall of consumption and the noise.
according to the opposite direction. tyre scratched. Regularly interchange the tyres. It is
Regularly inspect tyre surface for recommended to interchange four wheels for
Tyre cut trace, foreign body and uneven every 5,000 km. Namely, interchange left
For your safety, please check the tyre wear. The uneven tread wear may front tyre with the right rear tyre, and
pressure after the tyres (including spare indicate the incorrect alignment of interchange the right front tyre with the
tyre) become cold. See the proposed tyre wheel. left rear tyre.
pressure in the chapter “Capacity and
Specification”.
Replacement of Tyre
The tyres used by your vehicle are properly
chosen to provide the best vehicle control,
comfort and safety. The above-mentioned
combined provisions of tyre and rim are
applicable to the steel or aluminum alloy wheel
rim. If you want to know whether other types
74
Parameters of Capacity and Specifications
75
Parameters of Capacity and Specifications
76
Parameters of Capacity and Specifications
77
Parameters of Capacity and Specifications
78
Parameters of Capacity and Specifications
79
Parameters of Capacity and Specifications
Remarks
Process Process Name
5,000 15,000 30,000
15 Finish the inspection ★ ★ ★
16 Inspect the high-low horn ★ ★ ★
17 Inspect the rear lighting ★ ★ ★
18 Inspect the rear brake lamp ★ ★ ★
19 Inspect the left-rear turn lamp ★ ★ ★
20 Inspect the right-rear turn lamp ★ ★ ★
21 Inspect the rear alarm lamp ★ ★ ★
22 Inspect the rear reversing lamp ★ ★ ★
23 Inspect the rear fog lamp ★ ★ ★
24 Inspect the license lamp ★ ★ ★
25 Finish the inspection ★ ★ ★
26 Inspect the steering wheel ★ ★ ★
27 Inspect all buttons of air conditioner ★ ★ ★
28 Inspect the air state of air outlet ★ ★ ★
29 Inspect all indicator lamps of instruments ★ ★ ★
30 Inspect the control performance of parking handle ★ ★ ★
31 Inspect the gearlever ★ ★ ★
32 Inspect the clutch pedal ★ ★ ★
80
Parameters of Capacity and Specifications
Remarks
Process Process Name
5,000 15,000 30,000
33 Inspect the brake pedal and the accelerator pedal ★ ★ ★
34 Inspect the front and rear wiper blades and the nozzle ★ ★
35 Inspect all keys of instrument panel ★ ★ ★
36 Inspect the CD player and the loudspeaker ★ ★ ★
37 Inspect the front ceiling lamp ★ ★ ★
38 Inspect the rear-view mirrors on both sides ★ ★ ★
39 Inspect the central control door lock ★ ★ ★
40 Inspect the electric glass regulators of all doors ★ ★ ★
41 Inspect the sun visor, the teacup stand and the ash tray ★ ★ ★
42 Inspect the cigar lighter, the sundries box and the electronic clock ★ ★ ★
43 Inspect the driver’s seat, the safety belt, the switch of front door and the door lock hinge ★ ★
44 Inspect the left-rear door’s glass regulator, door switch, door hinge, seat and safety belt ★ ★
45 Inspect the right-rear door’s glass regulator, door switch, door hinge, seat and safety belt ★ ★
46 Inspect the right-front door’s glass regulator, door switch, door hinge, seat and safety belt ★ ★
47 Open the rear door and inspect the door lock hinge, the accompanying tools and the spare tyre ★ ★ ★
48 Open the engine hood ★ ★ ★
49 Install the protective cover of fender ★ ★ ★
81
Parameters of Capacity and Specifications
Remarks
Process Process Name
5,000 15,000 30,000
50 Inspect the air cleaner core ★ ★ ★
51 Inspect the gap and burning state of ignition plug ★ ★
52 Inspect the power steering oil ★ ★ ★
53 Inspect the cleaning fluid of windshield ★ ★ ★
54 Inspect and measure the engine coolant ★ ★ ★
55 Inspect the battery ★ ★
56 Inspect the volume of transmission oil ★ ★ ★
57 Inspect the volume of engine oil ★ ★ ★
58 Inspect the level of brake fluid ★ ★ ★
59 Inspect the timing belt ★
60 Inspect the generator belt ★ ★ ★
61 Inspect the pipeline of air conditioner ★ ★ ★
62 Inspect the cooling pipeline ★ ★ ★
63 Inspect the oil leakage at upside of engine ★ ★ ★
64 Inspect the engine harness ★ ★ ★
65 Inspect the shock absorber ★ ★ ★
66 Unscrew the tyre bolts ★ ★ ★
67 Support the vehicle ★ ★ ★
82
Parameters of Capacity and Specifications
Remarks
Process Process Name
5,000 15,000 30,000
68 Initially raise the vehicle ★ ★ ★
69 Remove the tyres ★
70 Inspect the brake pad ★
71 Inspect the wheel hub bearing for abnormal noise ★ ★
72 Inspect the pressure and appearance of tyres ★ ★ ★
73 Change the positions of tyres ★
74 Inspect the pressure and appearance of spare tyre ★ ★ ★
75 Raise the vehicle again ★ ★ ★
76 Drain the old engine oil and install back the oil block ★ ★ ★
77 Replace the engine oil filter with new one and clean the bottom of engine ★ ★ ★
78 Replace the gear oil of gearbox with new one and clean the gearbox ★
79 Replace the petrol filter with new one ★
80 Inspect the torque of chassis bolt ★ ★
81 Inspect the rear axle and the fuel tank ★ ★ ★
82 Inspect the relevant pipelines of chassis for oil leakage ★ ★ ★
83 Inspect the transmission shaft and the steering tie rod ★ ★ ★
84 Inspect the protective sleeve of transmission shaft universal joint for breakage ★ ★ ★
85 Inspect the protective sleeve of steering cross tie rod universal joint assembly for breakage ★ ★ ★
83
Parameters of Capacity and Specifications
Remarks
Process Process Name
5,000 15,000 30,000
86 Inspect the ball-head protective sleeve of knuckle and the clearance ★ ★ ★
87 Lower the vehicle ★ ★ ★
88 Fasten the tyre nuts and install back the spare tyre and the accompanying tools ★
89 Add the specified-volume engine oil ★ ★ ★
90 Start the engine for 3 minutes ★ ★ ★
91 Test the engine computer and the sensor ★ ★ ★
92 Shut down the engine, wait for 90 seconds and then confirm the level of engine oil ★ ★ ★
Raise the vehicle again, inspect the engine oil filter, the oil pan, the oil drain bolts and the gearbox for oil leakage, and then lower
93
the vehicle ★ ★ ★
94 Conduct the trial run to inspect the vehicle, and then fill in the work card with all inspection results ★ ★ ★
95 Wash the vehicle ★ ★ ★
96 Accompany the customer to inspect the vehicle and pay the fares ★ ★ ★
97 Remind the customer of the next maintenance ★ ★ ★
98 Take off three sleeves and one pad ★ ★ ★
99 Thanks and look after the customer ★ ★ ★
Note: For the manual transmission, replace the gear oil of transmission every year or every 30,000km; replace the brake fluid every 2 years or every 50,000km.
84
Parameters of Capacity and Specifications
Note: The first maintenance is applicable within 5,000 km or 6 months, whichever comes earlier.
85
Parameters of Capacity and Specifications
Maintenance Care for First 5,000km (within 6 Months after Purchase) Maintenance Care for First 5,000km
Note: The first maintenance is applicable within 5,000 km or 6 months, whichever comes earlier. Signature of Car Owner ___________
86
Parameters of Capacity and Specifications
Maintenance Certification
The maintenance shall be conducted according to the items specified in Regular Technical Maintenance of A3 Car. (The maintenance is subject
to the forementioned mileage and time, whichever comes earlier.)
87
Parameters of Capacity and Specifications
Date:________________
Date: ________________ Date: ________________
Mileage:
Mileage: Mileage:
________________
________________ ________________
The maintenance shall be conducted according to the items specified in Regular Technical Maintenance of A3 Car. (The maintenance is subject
to the forementioned mileage and time, whichever comes earlier.)
88
Parameters of Capacity and Specifications
The maintenance shall be conducted according to the items specified in Regular Technical Maintenance of A3 Car. (The maintenance is subject
to the forementioned mileage and time, whichever comes earlier.)
89
Parameters of Capacity and Specifications
The maintenance shall be conducted according to the items specified in Regular Technical Maintenance of A3 Car. (The maintenance is subject
to the forementioned mileage and time, whichever comes earlier.)
90
Parameters of Capacity and Specifications
The maintenance shall be conducted according to the items specified in Regular Technical Maintenance of A3 Car. (The maintenance is subject
to the forementioned mileage and time, whichever comes earlier.)
91
Parameters of Capacity and Specifications
The maintenance shall be conducted according to the items specified in Regular Technical Maintenance of A3 Car. (The maintenance is subject
to the forementioned mileage and time, whichever comes earlier.)
92
Parameters of Capacity and Specifications
1.---------------------------- 1.----------------------------
2.---------------------------- 2.----------------------------
3.---------------------------- 3.----------------------------
4.---------------------------- 4.----------------------------
Date:------------------------ Date:------------------------
Official Seal of Special Service Station: Official Seal of Special Service Station:
93
Parameters of Capacity and Specifications
Official Seal of Special Service Station: Official Seal of Special Service Station: Official Seal of Special Service Station:
94
Parameters of Capacity and Specifications
Official Seal of Special Service Station: Official Seal of Special Service Station: Official Seal of Special Service Station:
Official Seal of Special Service Station: Official Seal of Special Service Station: Official Seal of Special Service Station:
95
Parameters of Capacity and Specifications
96
Introduction
Vehicle Identification Description
Vehicle
Identification
number
Vehicle
nameplate
97
Introduction
Vehicle Identification Number Vehicle Name Plate If the high quality gasoline with additives is
The VIN of Chery A3 vehicle is engraved unavailable at the very moment, or in case of
under the roof drip on the front wall as engine malfunctions, such as difficult starting,
shown in the above figure. rough idle or power dip etc, proper additives
98
Introduction
such damage is out of the warranty scope of special oil for Chery vehicles. Your vehicle
the Chery company. engine is designed for the use of this special Do not use engine oil that does
To avoid the possible accident from wrong oil. Be sure to use the required oil to achieve not meet the above specifications and
fuel filling, the fuel tank is designed with a the best performance of the vehicle. requirements. The improper use of engine
collaring oil filler cap. Only the oil gun with oil may damage the engine and this
unleaded gasoline could be put into it. Do not use the additives or engine damage is out of the warranty scope of
Vehicle equipped with the catalytic converter finishing agent that have not been verified the Chery company.
can only use unleaded gasoline. by Chery company, as such additives are Vehicle Oil
not necessary, and they may damage the Replace the oil at intervals as shown in the
If you fill the oil tank with leaded engine under certain conditions and such maintenance section.
gasoline by accident, don’t start the engine damage is out of the warranty scope of Transmission Oil
(even though only a little is added), as the the Chery company. Use special oil for Chery vehicles. The
lead contained in the fuel will permanently Engine Oil Filling authorized service station provides the
damage the catalytic converter. It is Chery authorized service station will keep special oil for Chery vehicles.
recommended to contact the nearest the records of the relevant oil replacement Check the oil level periodically in normal
Chery authorized service station date and will use the special engine oil. The check period.
immediately. addition of engine oil should not exceed the Power-assisted Steering Oil
Engine Oil MAX mark on the oil dipstick. Always use the hydraulic oil that meets the
Engine Oil Replacement For the detailed suggestion or information, specifications of Chery. The authorized
Use the special oil for Chery vehicles. The Chery authorized service station is willing to service station provides original oil for Chery
authorized service station provides the help you. vehicles.
99
Introduction
Brake Fluid windshield (1:20). If the temperature outside Washing system for
MAX mark
Use Dot4 brake fluid. Fill the fluid to the Max the vehicle is too low, use winter washing windshield
mark as required. Only use the brake fluid liquid for windshield. Oil tank 57L
without paraffin wax. Follow the instructions on the container for Brake fluid reservoir MAX mark
proper thickness. Vehicle Weight
When the vehicle is heavy loaded, The curb weight means the weight that the
such as towering a tail car, traveling on vehicle can travel with, including the weight
Do not throw away the empty or
mountainous area for a long time, brake of coolant, lubricating oil, oil tank filled up to
waste engine oil container and filter as
fluid should also be replaced when 90%, tools, spare tyre and the driver (75kg).
household rubbish. Make use of the local
replacing the brake gasket. Be sure to The payload capacity is the permitted gross
authorized waste treatment equipment.
keep the brake fluid absolutely clean weight subtracts the curb weight.
during refilling. Any dirt coming into the Optional parts and subsequent additional
Parameter Table of Capacity and
brake system may disable the braking equipment will reduce the payload weight.
Specifications
performance. Parameters of Capacity and Specifications (liter)
Engine oil (including 4.5L
Coolant filter) Abide by the specified weight on
Use the coolant meeting the specifications Manual transmission 2.1±0.5L the Manual (if applicable), and permitted
of Chery. The authorized service station Power-assisted gross weight can’t be exceeded, as this
MAX mark
steering
provides the original oil for Chery vehicles. may change the brake and control
Cooling system 7.0L
Washing Liquid for Windshield performance, which may result in
Fill the liquid reservoir with Chery specified accident.
condensed liquid and water for the
100
Introduction
Parameters of Mass
101
Introduction
Wheels and Tyres ● When the tyres are used in winter, the pressure data listed in
102
Introduction
Engine information
Engine model SQR481F SQR484FC SQR484F
Engine type upright, 4-cylinders inline, water-cooled, 4 strokes, double overhead camshafts
Cylinder diameter (mm) 81 81 83.5
Piston stroke (mm) 77.5 89.5 90
Displacement (mL) 1,597 1,845 1,971
Compression ratio 10.5:1 10.5:1 10:1
Rated power (kW) 87.5 97 102
Rotary speed at rated power (r/min) 6,150 5,750 5,750
Max. torque (Nm) 147 170 182
Rotary speed at Max. torque (r/min) 4,300-4,500 4,300-4,500 4,300-4,500
Min. fuel consumption rate (g/kW·h) 250 264 250
*Only start to adjust or check at least five minutes after the engine stops.
103
Introduction
Vehicle Dimensions
104
Introduction
105