Professional Documents
Culture Documents
Release 3.1A
TABLE OF CONTENTS
ED 01 DRAFT
56
- 1.3.2.6 Install the redundant FLC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
- 1.3.3 Check the Status and the Persistency Synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
- 1.3.4 Rawloader Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
- 1.3.5 Connect the Craft Terminal to the 1678 MCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
not permitted without written authorization from Alcatel.
ED 01 DRAFT
56
LIST OF FIGURES AND TABLES
ED 01 DRAFT
56
1 INITIAL INSTALLATION OF THE FLC SOFTWARE
1.1 Preconditions
not permitted without written authorization from Alcatel.
All rights reserved. Passing on and copying of this
document, use and communication of its contents
– This document describes an initial installation of the FLC for the 1678 Metro Core Connect R3.1A.
– One or two FLCs are available and equipped with an EM04A and an DCR board.
• The FLCs are coming from factory and have never been installed before.
In this case both FLC boards must be plugged out before starting installation.
• The FLCs have already been installed before ( with old CORE, SKY or ION releases ).
In this case both FLCs must be in Maintenance state before starting installation.
– During installation only one LAN cable connected to one of the two redundant FLCs is supported.
– A Debug–Cable ( console cable ) for connection between installServer and FLC must be available
( only used during the installation ).
1 E 1
Length ~ 10 m F 2
2 E
to EM 3
COM1 3 F A 4
9600 bd 4 B 5
5 D 6
C 7
D 8
1
to DCR 2 B
COM2 or
COM5 3 A
38400 bd 4 C
5 D
Line D = GND
COM5 ( usb5toserial )
1AA 00014 0004 (9007) A4 – ALICE 04.10
ED 01 DRAFT
56
FLC
LAN Cable
HUB
not permitted without written authorization from Alcatel.
All rights reserved. Passing on and copying of this
document, use and communication of its contents
F–Interface
CT
Debug Cable
Installserver EM
DCR
It must be checked that the Voltage difference between the electrical ground of the
1678MCC and the Safety Edge of the 110/220V NET is lower than 3V! In case of a higher
voltage difference please contact PSC before proceeding further.
– 3xCD-ROMs with
• the FLC Platform Software ( CORE build + Rawloader V8.1.0 from 20.Juli 2004).
• the FLC Application Software ( SKY build + U–Boot Rawloader as rpm package).
– The CORE–xxx CD must be copied ( inserted ) first to the PC/Laptop ( see 1.2.1.1 e) ).
– The DCR board must be equipped with 512 MByte of main memory. This can be checked during boot-
ing of the DCR board. Look for the line “Physical memory Equipped” during booting. A reboot can
be triggered by pressing the reset button once on the FLC.
– The Compact Flash Card (CF) on the DCR board is not used but has to be plugged in.
– The configuration of the GMRE nodeAddress is described in the Network Configuration Guide.
– The following data must be available for the configuration of the FLC ( after installation ):
• Area address and System ID ( must be unique; e.g the MAC address of the DCR board can
be used as System ID ).
1AA 00014 0004 (9007) A4 – ALICE 04.10
ED 01 DRAFT
56
– The following data must be available ( requested by the aiGuideWizzard tool ):
• a terminal emulation program ( e.g Hyperterminal, Tera Term Pro ) used as terminal to the
console of EM04A and DCR boards.
• a hexcalculator ( for converting the MAC–address of the FLC into hex format)
ED 01 DRAFT
56
1.2 Detailed Description of the Installation Sequence of FLC
not permitted without written authorization from Alcatel.
The installation of both FLC at the same time is currently not supported. Therefore the installation
All rights reserved. Passing on and copying of this
document, use and communication of its contents
All the screenshots used in this detailed description are just examples.
These steps have to be done only once until the software versions are unchanged.
This can be done within the Windows2000 explorer or by using a Cygwin window.
b) Insert the CORE CD into the CD drive. Sometimes the insertion of the CD is not recognized. In this
case remove and insert the CD into the CD drive again.
c) Remove the CORE CD. Insert the SKY CD–ROM into the CD drive.
ED 01 DRAFT
56
not permitted without written authorization from Alcatel.
All rights reserved. Passing on and copying of this
document, use and communication of its contents
d) Remove the SKY CD. Insert the ION CD into the CD drive if required.
1AA 00014 0004 (9007) A4 – ALICE 04.10
ED 01 DRAFT
56
Press the “Finished” button after the download was finished. Remove the ION CD.
e) Setup of the sibdl tool by executing the following command using the Windows2000 explorer:
C:\ALCATEL\release\CORE–xxx\FLC\pack\rawloader\SIBDL_setup_2_2_0.exe
not permitted without written authorization from Alcatel.
Select “English ( United States )” as language in the “Choose Setup Language” dialog and press
the “OK” button.
Select the “C:\ALCATEL\SIBDL_2.2.0” directory.
The “View readme file” button can be deselected. Press the “Finish” button at the end of the sibdl
setup.
Close the readme.txt file with “File –> Exit” in case of selected “View readme file” button.
The SIBDL tool is installed now.
Press the “OK” button.
f) Adapt the network configuration of the installServer PC/Laptop to the network configuration of the
FLC. Use therefore a free IP–Address in the subnet of the FLC to be installed.
Only one LAN interface must be configured on the installServer! Disable all other LAN
connection used before ( example: LAN used for F–Interface, PCMCIA or a second LAN
interface ).
ED 01 DRAFT
56
not permitted without written authorization from Alcatel.
All rights reserved. Passing on and copying of this
document, use and communication of its contents
ED 01 DRAFT
56
not permitted without written authorization from Alcatel.
All rights reserved. Passing on and copying of this
document, use and communication of its contents
Configure the IP Configuration of the installServer using the “Use the following IP address” dialog.
The configuration of DNS server is not necesary.
a) Connect the installServer via LAN interface to the FLC ( over hub/switch or directly ).
b) Connect the console cable between the COM1 and COM2/COM5 of the installServer PC/Laptop with
the console interface on the FLC. Refer to Figure 1. on page 4.
The console cable must be plugged in on both serial interfaces of the installServer.
Otherwise the DCR board may be blocked.
1AA 00014 0004 (9007) A4 – ALICE 04.10
ED 01 DRAFT
56
1.2.2 FLC Installation
not permitted without written authorization from Alcatel.
Configure the Console window (installServer <–> EM04A) using the serial interface COM1.
Configure the Console window (installServer <–> DCR) using the interface COM2 or COM5.
b) If the FLC to be installed have an already running application in active or passive state, you have to
shutdown the application on both FLCs before starting the installation. The application on the passive
FLC must be stopped first to avoid an FLC switch.
Login to the passive/active FLC as user appl using a cygwin window and shutdown the passive/ac-
tive FLC:
$ ssh appl@<ip_address_of_the_EM_board>
Password:
Last login: Tue Jan 25 12:25:23 2005 from 149.204.73.65 on pts/6
Linux emServA88 2.4.20_mvl31–menem04 #1 Thu Sep 23 17:50:10 MEST
2004 ppc unknown
appl@emServA88:~$ bash
appl@emServA88(appl)$
1AA 00014 0004 (9007) A4 – ALICE 04.10
appl@emServA88(appl)$ start
ED 01 DRAFT
56
appl@emServA88(START)$ SSUDiag –c shutSSU
d) If the FLC is a new one from factory ( never been installed before ) plug in the FLC to be installed
and interrupt immediatelly the download of the EM04A board by pressing Esc in the Console window.
The EM04A board should be in MenMon mode afterwards.
appl@localDCR:~$ su – root
root@localDCR:~$ reboot
and stop the boot sequence by sending a break command on the console window.
Change into the pSH mode and check the rawloader version with the command:
pSH+> raw
or in case of UB–01A or newer stop the boot sequence by pressing any key and check the rawloader
version:
=> ver
If the DCR board is blocking please press the reset button on the FLC once. This will cause a reboot
anyway.
ED 01 DRAFT
56
not permitted without written authorization from Alcatel.
All rights reserved. Passing on and copying of this
document, use and communication of its contents
If the RAWLOADER Version is not V8.1.0 from 20 Juli 2004 continue with 1.2.2.3, else go on with
1.2.2.4.
c) Open a command window under Windows2000 ( Start –> Run –> cmd ).
COM<x> means:
the serial interface number connected to the DCR board
ED 01 DRAFT
56
not permitted without written authorization from Alcatel.
All rights reserved. Passing on and copying of this
document, use and communication of its contents
f) Reconnect the console to the DCR board using the TeraTerm dialog “File –> New Connection”, choo-
se the COM2/COM5 serial port and press the “OK” button.
GEN> reset –p
Press enter to get the pSH+> prompt.
if following prompt is shown type in
pROBE+> gs
pROBE+> go
pSH+>
1AA 00014 0004 (9007) A4 – ALICE 04.10
ED 01 DRAFT
56
g) Trouble shooting
not permitted without written authorization from Alcatel.
All rights reserved. Passing on and copying of this
document, use and communication of its contents
This error appears if the TeraTerm window or the console connection is not closed.
** DL_file process **
– Downloaded 159 data record and skipped 51 in 00:07:24 (3581 bytes/sec)
– BDL stopped
– serial port closed
1AA 00014 0004 (9007) A4 – ALICE 04.10
ED 01 DRAFT
56
not permitted without written authorization from Alcatel.
All rights reserved. Passing on and copying of this
document, use and communication of its contents
After installing the rawloader and executing ’reset –p’ the DCR may boot from Flash Card instead
from disk. This may happen if a bootable image is found on the Flash Card. This may be indicated
by the following trace:
Read Boot Table /home/adm–lc–ng/config/BT_EC
ED 01 DRAFT
56
1.2.2.4 Start the Installation
Only a part of the FLC configuration is done in this step. The final configuration is done after the instal-
not permitted without written authorization from Alcatel.
During installation only one LAN cable connected to one of the two redundant FLCs is
supported.
Additionally only one LAN Interface must be configured on the installServer. Disable all
other LAN Interfaces except the one where the installServer is connected to the FLC.
ED 01 DRAFT
56
All rights reserved. Passing on and copying of this
document, use and communication of its contents
not permitted without written authorization from Alcatel.
1AA 00014 0004 (9007) A4 – ALICE 04.10
ED
01
DRAFT
Enter the name and location of the NE. Press the “Next” button.
56
3AL 24169 ABAA PCZZA
19 / 56
All rights reserved. Passing on and copying of this
document, use and communication of its contents
not permitted without written authorization from Alcatel.
1AA 00014 0004 (9007) A4 – ALICE 04.10
ED
01
ment.
DRAFT
Press the “Next” button.
56
3AL 24169 ABAA PCZZA
Enter the software packages to be installed. Select the ION package only in case of GMRE enviro-
20 / 56
not permitted without written authorization from Alcatel.
All rights reserved. Passing on and copying of this
document, use and communication of its contents
Enter the correct IP address of the default gateway ( must be the router address ). Enter the IP ad-
dress for the local Craft Terminal and the NTP server. The configuration of the NTP server is man-
datory. The subnet address, the subnet mask and the gateway will be automatically retrieved from
the installServer configuration.
If an NE should have a connection to the outside world via gateway, you have to enable the gateway
access in the dialog above.
ED 01 DRAFT
56
not permitted without written authorization from Alcatel.
All rights reserved. Passing on and copying of this
document, use and communication of its contents
Enter the IP addresses of the activeEM, activeDCR, emCong, emServ, dcrServ and dcrCong board.
For the emCong, emServ, dcrServ and dcrCong also a hostname is required. The MAC address of
the emCong and emServ must be configured in the following way:
ED 01 DRAFT
56
In case of missing redundant FLC a fictive MAC address should be used instead ( e.g.
00C03A2D0000 ).
FLC
not permitted without written authorization from Alcatel.
All rights reserved. Passing on and copying of this
document, use and communication of its contents
EM board
ED 01 DRAFT
56
not permitted without written authorization from Alcatel.
All rights reserved. Passing on and copying of this
document, use and communication of its contents
Enter the used stack configuration ( Area address and System ID ) for the 1678MCC.
ED 01 DRAFT
56
not permitted without written authorization from Alcatel.
All rights reserved. Passing on and copying of this
document, use and communication of its contents
Select the FLC to be installed. Check the network cables. If done select “I have checked the network
cables”.
Do not execute the network boot with ’/alcafai/configBoot –np’ as described in the figure
above. Instead use the reset button as described in the following paragraph if the EM
board is not yet in the MENMON mode.
If the FLC is not yet in MENMON mode you must reboot the FLC by pressing the reset button for
about 3 seconds. Both, EM and DCR board will reboot in this case. Interrupt the booting sequence
by pressing the ESC button just after the message “Init ECC memory...” appears ( refer to the follow-
ing figure ).
1AA 00014 0004 (9007) A4 – ALICE 04.10
ED 01 DRAFT
56
All rights reserved. Passing on and copying of this
document, use and communication of its contents
not permitted without written authorization from Alcatel.
1AA 00014 0004 (9007) A4 – ALICE 04.10
ED
01
DRAFT
MenMon> rst
MenMon> ee–def
56
3AL 24169 ABAA PCZZA
26 / 56
Press “Start Installation” button in the aiGuideWizzard just after the following message appears:
“Searching for server (BOOTP) ...” ( refer to the following figure ).
ED 01 DRAFT
56
1.2.2.5 Download of the CORE, SKY and ION Software
a) The netboot_xxx.img should download now. Do not stop the booting sequence on the EM con-
not permitted without written authorization from Alcatel.
sole.
All rights reserved. Passing on and copying of this
document, use and communication of its contents
b) After loading of the netboot–xxx.img image, the netboot linux will be uncompressed and installed on
the FLC. This netboot linux will trigger the CORE build installation ( copy and unpack of the montavis-
ta linux ) on the EM04A and DCR board.
d) The ION installation will be started automatically ( only if the ION installation is required ).
ED 01 DRAFT
56
not permitted without written authorization from Alcatel.
All rights reserved. Passing on and copying of this
document, use and communication of its contents
Ignore the displayed Errors or Warnings as long as the status report shows “0 errors”, “0 warnings”
and the “aiGuide was SUCCESSFULL” message appears.
f) Due to the fact that the installation is running automatically, the installation can only be observed.
1AA 00014 0004 (9007) A4 – ALICE 04.10
On installServer:
ED 01 DRAFT
56
• If BOOTP requests are not responded you may stop the aiGuideWizzard.
After stopping the aiGuideWizzard, execute the following command in a cygwin window on the
installServer:
not permitted without written authorization from Alcatel.
This command will print out all detected incoming BOOTP requests
and you’ll easily see if you got an request from an unexpected MAC.
• with ’ps –ef’ the runnig daemons can be checked. This can be alternatively checked via:
./installserver/bin/installserver status
On the FLC:
The installation progress can be supervised with the FLC installation wizzard window. Do not press
the “Exit” button until the installation is finished.
ED 01 DRAFT
56
Press again the “Exit” button.
It may happen that the following or a similar error message appears. This error can be
ignored if in the EM–COM1 console window no errors or warnings are shown.
not permitted without written authorization from Alcatel.
All rights reserved. Passing on and copying of this
document, use and communication of its contents
Wait until the installation is completed using the console window ( refer to Figure 8. ) or the aiGuide.trace
file. If the installation is finished successfully ( message “aiGuide was SUCCESSFULL” appears in the ai-
Guide.trace file or the console window ) complete the installation by pressing the “Exit” button.
1AA 00014 0004 (9007) A4 – ALICE 04.10
ED 01 DRAFT
56
not permitted without written authorization from Alcatel.
All rights reserved. Passing on and copying of this
document, use and communication of its contents
g) Check the date on the EM04A and DCR board via the “date” command. Both boards must have the
same date and time.
h) Check the modules file on the DCR board using a cygwin window. Login on the currently installed
FLC ( EM board ):
appl@emCongA88(appl)$start
appl@emCongA88(STARTUP)$ cat /dcrroot/etc/modules
cplab–dwl–fpga dwl_major=241
cplab–spi spi_major=240 flc=1
mac–drv
llc2–drv my_slot=20 issb_cfg=20
klapd
The issb_cfg parameter must be set to 20. If issb_cfg is not equal 20 you have to execute the worka-
rounds described in step i ) – k ), else continue with Chapter 1.2.2.6.
i) In case of wrong entries in the modules file, install the COREUpdate rpm package again as user
1AA 00014 0004 (9007) A4 – ALICE 04.10
install.
ED 01 DRAFT
56
appl@emCongA88(STARTUP)$ su – install
Password:
install@emCongA88(install)$ bash
install@emCongA88(install)$ sudo rpm −U − −force /packages/aiGuide/tmp.install/
not permitted without written authorization from Alcatel.
All rights reserved. Passing on and copying of this
document, use and communication of its contents
SKY10–xyz/LPPC/pack/COREUpdate–SKY10–xyz.ppc.rpm
j) After COREUpdate installation the inetd configuration contains a wrong blocksize (used by the tftp
daemon). Therefore you have to retrieve the original configuration by executing the following com-
mands:
install@emCongA88(install)$ su – root
Password:
# bash
root@emCongA88(root)$ cp /etc/inetd.conf.rpmsave /etc/inetd.conf
root@emCongA88(root)$ exit
# exit
installl@emCongA88(install)$ exit
install@emCongA88(install)$ exit
appl@emCongA88(STARTUP)$
k) Reset the related DCR board by executing the following command on the EM board:
appl@emCongA88(STARTUP)$ /usr/local/sbin/resetDCR
Check the modules file on the DCR board again by excuting step h ).
The installation of the redundant FLC is done in the same way as for the first FLC. Therefore repeat
the steps described in 1.2.2.1 b) to 1.2.2.5 k).
1AA 00014 0004 (9007) A4 – ALICE 04.10
ED 01 DRAFT
56
1.2.3 Check the Status and the Persistency Synchronization
not permitted without written authorization from Alcatel.
a) The application on both FLCs should run in ACTIVE/PASSIVE state. Check the state using the two
All rights reserved. Passing on and copying of this
document, use and communication of its contents
appl@emServA88(LogFiles)$start
appl@emServA88(STARTUP)$ SSUDiag –c getEquipInfo
<
b) Check the synchronization state on both FLCs. Use the same open cygwin windows.
appl@emServA88(STARTUP)$PersSync
ED 01 DRAFT
56
10 | MIB | 24597 | S | 0| T | F | F | 0K | 18 | F | F |
11 | MIB | 24597 | S | 0| T | F | F | 0K | 18 | F | F |
12 | MIB | 24597 | S | 0| T | F | F | 0K | 18 | F | F |
13 | no valid line in Offset–File with this index
not permitted without written authorization from Alcatel.
14 |CSServer | 1| S | 0| T | F | F | 0K | 18 | F | F |
All rights reserved. Passing on and copying of this
document, use and communication of its contents
15 |CSServer | 1| S | 0| T | F | F | 0K | 18 | F | F |
16 |GMRE_PM | 2| S | 0| T | F | F | 0K | 18 | F | F |
17 |GMRE_MA | 4| S | 0| T | F | F | 0K | 18 | F | F |
NVRAM access successfully ended!
All persistency domains should have the state “S” for synchronized.
ED 01 DRAFT
56
• Reset the DCR board from the EM board.
appl@emCongA85(appl)$ /usr/local/sbin/resetDCR
The DCR board is now booting with the new u–boot loader.
not permitted without written authorization from Alcatel.
• Check the installed rawloader during the reboot or by stopping the boot sequence ( only pos-
All rights reserved. Passing on and copying of this
document, use and communication of its contents
=> ver
U–Boot 1.1.1 (Jan 13 2005 – 18:52:51) – Alcatel SEL AG Stuttgart, Build: @(#)SEL Stuttgart
SCM ID: UBO–01B
=> reset
• Start the application on both FLCs again. The last ACTIVE FLC must be started first.
1AA 00014 0004 (9007) A4 – ALICE 04.10
ED 01 DRAFT
56
1.2.5 Connect the Craft Terminal to the 1678 MCC
not permitted without written authorization from Alcatel.
Connect the preinstalled and correctly configured CT ( LowerLayerManES required ) with the OMSG
All rights reserved. Passing on and copying of this
document, use and communication of its contents
Alcatel 1678 Metro Core Connect according to the customer network using the F–Interface.
If the CT is running on the installServer disconnect all used serial interfaces COM1 and COM2/5. Plug
out the EM debug cable on the PC/Laptop and the FLC side. Plug in the F–Interface cable to the
COM1 interface ( see Figure 2 ). To use the F interface it is required that the cable is plugged into
the ACTIVE FLC.
The FLC redundancy is not supported for F–Interface connections. After an FLC switch
the F–Interface connection will be broken. In this case reconnect the F–Interface cable to
the new ACTIVE FLC.
Menu
Sart –> Programs –> Alcatel –> Lower Layers –> Lower Layers Settings
Choose:
Serial Port
COM1
Default
Start the CT by double click the “Alcatel 1320CT” icon or via menue “START” –> “Alcatel 1320CT”.
Now you should be able to start supervision with the right mouse button menu on the CT.
1AA 00014 0004 (9007) A4 – ALICE 04.10
ED 01 DRAFT
56
–> Start Supervision.
Sometimes it can happen that the connection to the NE is not established. In this case shutdown the Low-
All rights reserved. Passing on and copying of this
document, use and communication of its contents
erLayerManES by pressing the “Shutdown” button and close an already open Map using the menu “Map”
–> “Exit”. Start the CT again by double click the “Alcatel 1320CT” icon.
If the previous workaround doesn’t solve the problem, kill the QIA process on the ACTIVE FLC.
ED 01 DRAFT
56
1.2.6 Create Main Shelf
eg.
Rack Id = 1
1AA 00014 0004 (9007) A4 – ALICE 04.10
Room = 1
Row = 1
Column = 1
ED 01 DRAFT
56
Press OK button.
eg.
Shelf Type = NGTRU
Top Subrack Id = 1
Subrack Position = 3
1AA 00014 0004 (9007) A4 – ALICE 04.10
Press OK button.
ED 01 DRAFT
56
not permitted without written authorization from Alcatel.
All rights reserved. Passing on and copying of this
document, use and communication of its contents
Create mainShelf
–> Edit
–> Create
–> Shelf
Enter Shelf Type, Shelf Id(hex), Top Subrack Id, Subrack Position, Matrix size
eg.
Shelf Type = MCC 1678
Shelf Id(hex) = 01
Top Subrack Id = 2
Subrack Position = 19
Matrix Size = 640G
According to the system configuration different Matrix Size must be configured. The following matrix sizes
1AA 00014 0004 (9007) A4 – ALICE 04.10
are supported:
1K 160
2K 320
4K 640 ( default )
ED 01 DRAFT
56
Select the correct Matrix Size.
Press OK button.
not permitted without written authorization from Alcatel.
Zoom in the new created mainShelf by double clicking on the Equipment View.
The SLC boards are not correctly configured after startAppl. Therefore the SLC boards must be re-
seted using the csReset command ( first the passive SLC board ). Execute the following commands
on the ACTIVE FLC:
appl@emServA88(LogFiles)$start
appl@emServA88(STARTUP)$ csReset –mx640ge MX640GEA ac
appl@emServA88(STARTUP)$ csReset –mx640ge MX640GEB ac
ED 01 DRAFT
56
1.2.8 Update the FLC Configuration
not permitted without written authorization from Alcatel.
The Update of the FLC configuration using the EP tool is described in the following section.
All rights reserved. Passing on and copying of this
document, use and communication of its contents
The GMRE Node Address and installserver configuration describe below is only necesary if the related
fields are empty or wrong. In case of valid entries nothing has to be changed.
Do not press the “OK” button. Press “IP DCN” for further configuration.
Configure GMRE Node Address and Install Server Ip Address in case of installation with ION software
installation ( NE with GMRE ):
Configure GMRE Node Address and Install Server Ip Address in case of installation without ION software
installation ( NE without GMRE ):
1AA 00014 0004 (9007) A4 – ALICE 04.10
ED 01 DRAFT
56
Do not press the “OK” button. Press “IP DCN” for further configuration.
not permitted without written authorization from Alcatel.
All rights reserved. Passing on and copying of this
document, use and communication of its contents
Do not press the “OK” button. Press “OSI DCN” for further configuration.
Check the configuration of the the NTP Server in the “NTP Server” dialog. The configuration of
the NTP server is mandatory.
1AA 00014 0004 (9007) A4 – ALICE 04.10
ED 01 DRAFT
56
not permitted without written authorization from Alcatel.
All rights reserved. Passing on and copying of this
document, use and communication of its contents
Enter the corresponding SH, CT and additional WS. All host which should have access to the NE
must be entered using this dialog ( IP address and hostname ).
Backup and Restore is only possible if the SH/CT is configured under “Other IP Hosts” !
1AA 00014 0004 (9007) A4 – ALICE 04.10
ED 01 DRAFT
56
not permitted without written authorization from Alcatel.
All rights reserved. Passing on and copying of this
document, use and communication of its contents
• Enter the NSAP address of the manager in the NSAP Address field
• Enter the name of the transport selector in the TSEL text field
• Enter the name of the session selector in the SSEL text field
• Enter the name of the presentation selector in the PSEL text field
• Click on the add button to add the configuration data to the list
Examples:
SSEL 00
PSEL 1D
ED 01 DRAFT
56
SH OSI NSAP Address 4700058000000000000001000A0030D30140F21D
TSEL 0101
SSEL 00
PSEL 1D
not permitted without written authorization from Alcatel.
All rights reserved. Passing on and copying of this
document, use and communication of its contents
After pressing the ”OK” button in the EP tool, the FLCs are switching sometimes. The F–Interface
connection is down in case of FLC switch, while the F_interface must always be connected to the
ACTIVE FLC.
After FLC installation and configuration the SETUP_LAPD entries in the inbnd.conf file have default
values.
To save the configuration on both FLCs stop the running application on both FLCs ( begin with the
passive FLC to avoid FLC switches ).
appl@emCongA88(STARTUP)$SSUDiag –c shutAppl
appl@emCongA88(STARTUP)$SSUDiag –c shutSSU
Save the new configuration on both FLCs by executing the command saveCurrentIns-
tallation. This will take about 15 min.
appl@emServA88(START)$ su – maint
login: maint
Password:******
maint@emServA88(maint)$bash
maint@emServA88(maint)$sudo saveCurrentInstallation
1AA 00014 0004 (9007) A4 – ALICE 04.10
ED 01 DRAFT
56
If you want to monitor the saveCurrentInstallation procedure using a console cable, both console
windows (EM and DCR) must be opened and connected.
If the console cable is connected to the FLC, but the console windows are not opened or discon-
not permitted without written authorization from Alcatel.
Therefore we recommend to plug out the FLC console cable at the FLC during saveCurrentInstalla-
tion.
Check if the configured time server is already selected. To do this, use the following command:
appl@emServA88(START)$ ntpq –p
ED 01 DRAFT
56
not permitted without written authorization from Alcatel.
All rights reserved. Passing on and copying of this
document, use and communication of its contents
In order to avoid problems with IO boards the FPGA Goblin on the IO board must have the version
3.5. Therfore you have open telnet session to the active SLC. The Goblin version is contained in the
FPGA register 0 and 1. In our example the FPGA register 0 contains “3”, while the FPGA register 1
contains “5”. The version of the Goblin is 3.5.
pSH+> hw_cfg
HW–CFG–DRV device–driver
––––––––––––––––––––––––
[0] Display all the HW–CFG debug–counter variables.
[1] Read FPGA register.
[2] Test Cmd (You could erase all the data saved on Flash Memory).
[3] Test Driver (You could erase all the data saved on Flash Memory).
[4] Enable/Disable message tracement.
[5] Display error codes.
Select : 1
0 version
1 hidden_version
2 flash_op
3 fpga_download
Insert register address : 0
1AA 00014 0004 (9007) A4 – ALICE 04.10
ED 01 DRAFT
56
pSH+> hw_cfg
HW–CFG–DRV device–driver
not permitted without written authorization from Alcatel.
––––––––––––––––––––––––
All rights reserved. Passing on and copying of this
document, use and communication of its contents
Select : 1
0 version
1 hidden_version
2 flash_op
3 fpga_download
Insert register address : 1
pSH+>
The fan speed can be read on pShell / telnet session to the ACTIVE SLC with command:
In this case the fan speed must be adjusted with the following command:
ED 01 DRAFT
56
1.3 Short Description of the Installation Sequence of FLC
not permitted without written authorization from Alcatel.
This is the short installation description of the FLCs. This description has been written for well trained
All rights reserved. Passing on and copying of this
document, use and communication of its contents
The installation of both FLC at the same time is currently not supported. Therefore the installation
must be executed for each FLC separately.
These steps have to be done only once until the software versions are unchanged.
b) Insert the CORE, SKY and ION CD successive into the CD drive. Begin with the CORE CD.
c) Setup of the sibdl tool by executing the following command using the Windows2000 explorer:
C:\ALCATEL\release\CORE–xxx\FLC\pack\rawloader\SIBDL_setup_2_2_0.exe
Install the sibdl tool to the C:\ALCATEL\SIBDL_2.2.0 directory.
e) Adapt the network configuration of the installServer PC/Laptop to the network configuration of the
FLC. Use therefore a free IP–Address in the subnet of the FLC to be installed.
a) Connect the installServer via LAN interface to the FLC ( over hub/switch or directly ).
b) Connect the console cable between the COM1 and COM2/COM5 of the installServer PC/Laptop with
the console interface on the FLC. Refer to Figure 1. on page 4.
b) If the FLC to be installed have an already running application in active or passive state, you have to
shutdown the application on both FLCs before starting the installation. The application on the passive
FLC must be stopped first to avoid an FLC switch.
1AA 00014 0004 (9007) A4 – ALICE 04.10
c) If the FLC is already plugged in refer to chapter 1.3.2.4 b) on page 52 for later reboot.
ED 01 DRAFT
56
d) If the FLC is a new one from factory ( never been installed before ) plug in the FLC to be installed
and interrupt immediatelly the download of the EM04A board in the Console window. The EM04A
board should be in MenMon mode afterwards.
not permitted without written authorization from Alcatel.
a) Change to the DCR console window on the PC/Laptop. Reboot the DCR board and send a break to
get the pSH+> shell. Check the rawloader version.
pSH+> raw
b) If the DCR board is blocking please press the reset button on the FLC once. This will cause a reboot
anyway.
c) If the RAWLOADER Version is not V8.1.0 from 20 Juli 2004 continue with 1.3.2.3 , else skip to
1.3.2.4.
c) Open a command window under Windows2000 ( Start –> Run –> cmd ).
where “COM<x>” is the used serial interface connected to the DCR board
f) Reconnect the console to the DCR board using the dialog “File –> New Connection”, choose the
COM2/COM5 serial port and press the “OK” button.
GEN> reset –p
Press enter to get the pSH+> prompt.
pSH+>
b) Enter the required FLC configuration data. The NTP server is mandatory.
1AA 00014 0004 (9007) A4 – ALICE 04.10
If the FLC is not yet in MENMON mode you must reboot the FLC by pressing the reset button for
about 3 seconds. Both, EM and DCR board will reboot in this case. Interrupt the booting sequence
by pressing the ESC button just after the message “Init ECC memory...” appears.
ED 01 DRAFT
56
Enter the following commands in the MENMON mode:
MenMon> ee–def
MenMon> rst
not permitted without written authorization from Alcatel.
Press “Start Installation” button in the aiGuideWizzard just after the following message appears:
All rights reserved. Passing on and copying of this
document, use and communication of its contents
a) The netboot_xxx.img should download now. Do not stop the booting sequence on the EM con-
sole.
b) Trigger the CORE build installation on the EM04A and DCR board.
d) The ION installation will be started automatically ( only if the ION installation is required ).
f) Due to the fact that the installation is running automatically, the installation can only be observed. See
the detail description for other debugging hints.
Wait until the installation is completed using the console window ( refer to Figure 8. on page 29 ) or the
aiGuide.trace file.
g) Check the date on the EM04A and DCR board via the “date” command. Both boards must have the
same date and time.
h) Check the modules file on the DCR board using a cygwin window. Login on the currently installed
FLC ( EM board ):
appl@emCongA88(appl)$start
appl@emCongA88(STARTUP)$ cat /dcrroot/etc/modules
cplab–dwl–fpga dwl_major=241
cplab–spi spi_major=240 flc=1
mac–drv
llc2–drv my_slot=20 issb_cfg=20
klapd
The issb_cfg parameter must be set to 20. If issb_cfg is not equal 20 you have to execute the worka-
rounds described in step i ) – k ), else continue with Chapter 1.3.2.6.
i) In case of wrong entries in the modules file, install the COREUpdate rpm package again as user
install.
appl@emCongA88(STARTUP)$ su – install
Password:
install@emCongA88(install)$ bash
install@emCongA88(install)$ sudo rpm −U − −force /packages/aiGuide/tmp.install/
SKY10–xyz/LPPC/pack/COREUpdate–SKY10–xyz.ppc.rpm
1AA 00014 0004 (9007) A4 – ALICE 04.10
j) After COREUpdate installation the inetd configuration contains a wrong blocksize (used by the tftp
daemon). Therefore you have to retrieve the original configuration by executing the following com-
mands:
ED 01 DRAFT
56
install@emCongA88(install)$ su – root
Password:
# bash
root@emCongA88(root)$ cp /etc/inetd.conf.rpmsave /etc/inetd.conf
not permitted without written authorization from Alcatel.
root@emCongA88(root)$ exit
All rights reserved. Passing on and copying of this
document, use and communication of its contents
# exit
installl@emCongA88(install)$ exit
install@emCongA88(install)$ exit
appl@emCongA88(STARTUP)$
k) Reset the related DCR board by executing the following command on the EM board:
appl@emCongA88(STARTUP)$ /usr/local/sbin/resetDCR
Check the modules file on the DCR board again by excuting step h ).
The installation of the redundant FLC is done in the same way as for the first FLC. Therefore repeat
the steps described in 1.3.1.2 b) to 1.3.2.5 g).
All persistency domains should have the state “S” for synchronized.
• Logout from DCR board and reset the DCR board from the EM board.
appl@emCongA85(appl)$ /usr/local/sbin/resetDCR
• Check the installed rawloader during the reboot or by stopping the boot sequence ( only pos-
sible on the DCR console ).
During reboot the communication from SH to NE may be interrupted depending on which FLC the
LAN cable is plugged in.
Start the application on both FLCs again. The last ACTIVE FLC must be started first.
ED 01 DRAFT
56
1.3.5 Connect the Craft Terminal to the 1678 MCC
Connect the preinstalled and correctly configured CT ( LowerLayerManES required ) with the OMSG
Alcatel 1678 Metro Core Connect according to the customer network using the F–Interface.
not permitted without written authorization from Alcatel.
All rights reserved. Passing on and copying of this
document, use and communication of its contents
If the CT is running on the installServer disconnect all used serial interfaces COM1 and COM2/5. Plug
out the EM debug cable on the PC/Laptop and the FLC side. Plug in the F–Interface cable to the
COM1 interface ( see Figure 2 ). To use the F interface it is required that the cable is plugged into
the ACTIVE FLC.
Enter Shelf Type, Shelf Id(hex), Top Subrack Id, Subrack Position, Matrix size of the mainShelf.
Set the Matrix Size on the passive SLC ( Matrix ) board according to the system configuration.
Zoom in the new created mainShelf by double clicking on the Equipment View.
The SLC boards are not correctly configured after startAppl. Therefore the SLC boards must be re-
seted using the csReset command ( first the passive SLC board ).
appl@emServA88(LogFiles)$start
appl@emServA88(STARTUP)$ csReset –mx640ge MX640GEA ac
appl@emServA88(STARTUP)$ csReset –mx640ge MX640GEB ac
Update the FLC configuration using the EP tool as described in the detailed description on page 55.
After FLC installation and configuration the SETUP_LAPD entries in the inbnd.conf file have default
values.
1AA 00014 0004 (9007) A4 – ALICE 04.10
ED 01 DRAFT
56
Save the new configuration on both FLCs by executing the command saveCurrentInstalla-
tion. This will take about 15 min.
not permitted without written authorization from Alcatel.
In order to avoid problems with IO boards the FPGA Goblin on the IO board must have the version
3.5.
pSH+> hw_cfg
The fan speed can be read on pShell / telnet session to the ACTIVE SLC with command:
In this case the fan speed must be adjusted with the following command:
ED 01 DRAFT
56