Professional Documents
Culture Documents
INDEX BRUNDLE
As Britain’s leading distributor of welded mesh, we offer our customers the widest
range of top quality material, FROM STOCK.
Brundle welded mesh is manufactured from bright drawn mild steel wire to BS 1052.
Electronically welded at every intersection. It is produced in self colour (lightly copper coated) and galvanised after manufacture
to BS 443 or BS 729 on certain gauges such as 6g.
Some specifications are produced from galvanised wire and stainless steel, types 304 and 316.
19g - 1.00mm
16g - 1.50mm
14g - 1.93mm
12g - 2.44mm
10g - 3.00mm
8g - 3.94mm
6g - 4.69mm
FRAMED MESH PANELS
The sizes and specifications described are as accurate as tolerances allow. All information in this brochure is given in good faith.
However F.H.Brundle cannot accept responsibility for any loss or damage arising from the use of the products detailed herein.
F.H.Brundle reserves the right to amend or withdraw products without prior notice.
2
BRUNDLE WELDED WIRE MESH BRUNDLE
GUIDE TO STOCK SIZES
BRUN-MESH KLIPS
FOR JOINING MESH PANELS FOR FIXING UP TO 3.0mm THICK WIRE FOR FIXING UP TO 3.0mm
Brun-mesh Brun-mesh Klip THICK WIRE ON 2" x 2" MESH
Connector Klip (pre-galv finish) Brun-mesh Klip
Art. 07001 Art. 07005 (pre-galv finish)
Art. 07006
FOR FIXING UP TO
4.0mm THICK WIRE FOR USE WITH LIGHT
Brun-mesh Klip GAUGE MESH TO
19 x 33mm with 5mm hole CLIP MESH TO MESH
Galvanised - Art. 07002 Twilweld Clips
Stainless - Art. 07042 Art. 0109
3
BRUNDLE
WIRE NETTING AND WIRE BRUNDLE
wire size
Mesh
mm swg
roll width 50 metre rolls 25 metre rolls 10 metre rolls
13mm 0.70 22 900mm 090209132250 - 090209132210
13mm 0.70 22 1200mm - - 090212132210
25mm 0.90 20 600mm 090206252050 - -
25mm 0.90 20 900mm 090209252050 - 090209252010
25mm 0.90 20 1200mm 090212252050 - 090212252010
25mm 0.90 20 1800mm 090218252050 - -
31mm 1.00 19 600mm 090206311950 - -
31mm 1.00 19 1050mm 090210311950 - -
31mm 1.00 19 1200mm 090212311950 - -
50mm 1.00 19 900mm 090209501950 - 090209501910
50mm 1.00 19 1200mm 090212501950 - 090212501910
50mm 1.00 19 1800mm 090218501950 090218501925 -
100mm 1.60 16 900mm 0902091001650 - -
Art. 0702003
4
BRUNDLE
WOVEN WIRE MESH BRUNDLE
WOVEN WIRE MESH IS GENERALLY CHARGED BY THE SQUARE FOOT OR SQUARE METRE.
Mesh Wire Aperture Open Area Mesh Wire Aperture Open Area
Count Dia. mm AISI Width mm SWG % Count Dia. mm AISI Width mm SWG %
STAINLESS STEEL WOVEN MESH STAINLESS STEEL WOVEN MESH
2 2.00 316 48 10.70 (14) 71 36 0.25 304 48 0.46 (33) 42
2 1.60 304 48 11.10 (16) 76 40 0.18 304 48 0.46 (36) 51
3 2.00 316 48 6.47 (14) 58 40 0.22 304 48 0.44 (34) 42
3 1.60 304 48 6.87 (16) 66 40 0.22 316 36 0.44 (34) 42
3 1.60 316 48 6.87 (16) 66 S 40 0.22 316 48 0.44 (34) 42
4 1.60 304 48 4.35 (16) 56 50 0.18 304 48 0.33 (36) 42
4 1.25 304 48 5.10 (18) 64 60 0.16 304 48 0.26 (37.5) 39
4 0.90 304 48 5.45 (20) 74 60 0.16 316 48 0.26 (37.5) 39
5 1.00 304 48 4.08 (19) 64 70 0.15 304 48 0.212 (38) 34
6 1.60 304 48 2.63 (16) 39 80 0.14 304 48 0.178 (39) 31
6 1.25 304 48 2.98 (18) 50 80 0.14 316 36 0.178 (39) 31
6 0.90 304 48 3.33 (20) 62 80 0.14 316 48 0.178 (39) 31
8 0.90 304 48 2.28 (20) 51 100 0.10 304 48 0.154 (42) 37
8 0.71 304 48 2.47 (22) 60 100 0.10 316 48 0.154 (42) 37
10 0.90 304 48 1.64 (20) 42 100 0.11 316 48 0.142 (41) 31
10 0.56 304 48 1.98 (24) 61 120 0.09 316 48 0.122 (43) 33
10 0.56 316 48 1.98 (24) 61 150 0.065 316 48 0.104 (46) 42
12 0.80 316 48 1.32 (21) 39 150 0.07 316 48 0.098 (45) 34
12 0.56 316 48 1.56 (24) 54 165 0.05 304 48 0.104 (47) 46
14 0.45 304 48 1.36 (26) 56 180 0.05 316 48 0.091 (47) 42
16 0.71 304 50 0.88 (22) 30 200 0.04 304 48 0.087 (47) 37
16 0.45 316 48 1.14 (26) 51 200 0.05 316 48 0.077 (47) 37
16 0.355 304 48 1.23 (28.5) 60 200 0.05 304 60 0.077 (47) 37
18 0.40 304 48 1.01 (27) 51 230 0.035 304 48 0.075 (48.5) 45
20 0.45 304 48 0.82 (26) 42 250 0.04 304 48 0.062 (48) 37
20 0.355 304 48 0.92 (28.5) 51 270 0.035 304 48 0.59 (48.5) 39
20 0.355 316 48 0.92 (28.5) 51 300 0.036T 304 48 0.49 (48.5) 33
24 0.35 304 48 0.70 (28.5) 44 300 0.04T 316 48 0.045 (48) 28
28 0.35 304 48 0.55 (28.5) 37 325 0.028 304 48 0.50 (49.5) 41
30 0.28 304 48 0.57 (31.5) 45 325 0.028 304 61 0.50 (49.5) 41
30 0.28 316 48 0.57 (31.5) 45 400 0.03T 316 48 0.034 (49) 28
500 0.025T 316 1.3M 0.026 (50) 26
5
BRUNDLE
WOVEN WIRE MESH BRUNDLE
Mesh Wire Aperture Open Area Mesh Wire Aperture Open Area
Count Dia. mm AISI Width mm SWG % Count Dia. mm AISI Width mm SWG %
STAINLESS STEEL HOLLANDER MONEL
12/72 316 48 .300 - - 120 0.09 1M 0.122 43 33
24/110 304 48 .125 - - 200 0.05 1M 0.077 47 37
50/250 304 48 .063 - - 250 0.04 1M 0.062 48 37
TAILESS STEEL HOLLAN
MILD STEEL ALUMINIUM INSECT MESH
6 0.90 48 3.33 20 62 18/16 0.28 48 - - -
8 0.71 48 2.47 22 60 FIBREGLASS INSECT MESH
8 1.00 1M 2.18 19 47
F18/16 48 - - -
10 0.56 48 1.98 24 61
10 0.56 74 1.98 24 61 PHOSPHOR BRONZE
10 0.90 48 1.64 30 32 40 0.22 48 0.41 34 42
12 0.50 48 1.62 25 58 50 0.19 48 0.30 36 40
14 0.40 48 1.41 27 61 60 0.16 48 0.26 37 39
100 0.11 48 0.142 41 31
16 0.45 64 1.14 26 51 150 0.06 48 0.109 42 42
16 0.50 54 1.09 25 47 200 0.05 48 0.077 47 37
16 0.60 1M 0.96 23 36 300 0.035T 48 0.049 48 29
16 0.34 GALV 48 1.23 28 60 BRASS
20 0.35 61 0.92 28 51
8 0.71 48 2.47 22 60
20 0.40 48 0.87 27 47 10 0.56 48 1.98 24 61
30 0.30 51 0.53 30 39 16 0.35 48 1.23 28 60
40 0.25 51 0.39 33 37 20 0.35 1M 0.92 28 51
30 0.28 40 0.57 31 45
60 0.16 51 0.26 37 39 40 0.22 1M 0.41 34 42
60 0.16 48 0.35 37 47
MONEL 80 0.14 1M 0.178 39 31
20 0.35 48 0.92 28 51 COPPER
28 0.35 48 0.55 28 37
16 0.35 48 1.23 28 60
40 0.22 48 0.41 34 42 20 0.35 48 0.92 28 51
50 0.18 1M 0.46 36 51 28 0.35 48 0.55 28 37
60 0.16 48 0.26 27 39 30 0.28 48 0.57 31 45
40 0.22 48 0.41 34 32
100 0.11 36 0.142 41 31 60 0.16 48 0.26 37 39
If you know the reference number you require, then look below for standard stocked
items. Illustrations of some popular specifications are shown on the following pages.
Non-stocked items can be quickly produced. All patterns can be cut-to-size in
commercial quantities.
ALUMINIUM
GOLD ANODISED 351A 1220 x 915
351A 1250 x 1250
7
RAISED MESH
Expanded Steel Mesh
Ref. Mesh Size Size of Open Weight Sheet Size
Expanded Aluminium Mesh
No. Centre-Centre Strand Area Size
mm mm % mm Expanded Stainless
LW SW W T Norm Max Kgs/Sht LWM SWM
Steel Mesh Spec 304/S15
❊
957MM 1.50 0.92 0.22 0.15 46 54 0.160/Lm 212 Roll (Length to order)
957MM
❊
927S 3.175 1.81 0.254 0.152 60 66 1.088 420 x 10 metres
927S
901A
707S
602A
227S
203
LW denotes long way of mesh dimension. SW denotes short way of mesh dimension. All standard sheet sizes are nominal (normally oversize).
8
RAISED MESH
Expanded Steel Mesh
Ref. Mesh Size Size of Open Weight Sheet Size
Expanded Aluminium Mesh
No. Centre-Centre Strand Area Size
mm mm % mm Expanded Stainless
LW SW W T Norm Max Kgs/Sht LWM SWM
Steel Mesh Spec 304/S15
199
196S
1295
1294
1292
1597
1595
LW denotes long way of mesh dimension. SW denotes short way of mesh dimension. All standard sheet sizes are nominal (normally oversize).
9
RAISED MESH
Expanded Steel Mesh
Ref. Mesh Size Size of Open Weight Sheet Size
Expanded Aluminium Mesh
No. Centre-Centre Strand Area Size
mm mm % mm Expanded Stainless
LW SW W T Norm Max Kgs/Sht LWM SWM
Steel Mesh Spec 304/S15
1576
2091
2089
2088
3092
LW denotes long way of mesh dimension. SW denotes short way of mesh dimension. All standard sheet sizes are nominal (normally oversize).
10
RAISED MESH
Expanded Steel Mesh
Ref. Mesh Size Size of Open Weight Sheet Size
Expanded Aluminium Mesh
No. Centre-Centre Strand Area Size
mm mm % mm Expanded Stainless
LW SW W T Norm Max Kgs/Sht LWM SWM
Steel Mesh Spec 304/S15
3396
4097
4599
LW denotes long way of mesh dimension. SW denotes short way of mesh dimension. All standard sheet sizes are nominal (normally oversize).
11
FLATTENED MESH
Expanded Steel Mesh
Ref. Mesh Size Size of Open Weight Sheet Size
Expanded Aluminium Mesh
No. Aperture Strand Area Size
mm mm % mm Expanded Stainless
LW SW W T Norm Max Kgs/Sht LWM SWM
Steel Mesh Spec 304/S15
706F
226F
217F 217AF
197SF
1280F
1282F
LW denotes long way of mesh dimension. SW denotes short way of mesh dimension. All standard sheet sizes are nominal (normally oversize).
12
FLATTENED MESH
Expanded Steel Mesh
Ref. Mesh Size Size of Open Weight Sheet Size
Expanded Aluminium Mesh
No. Aperture Strand Area Size
mm mm % mm Expanded Stainless
LW SW W T Norm Max Kgs/Sht LWM SWM
Steel Mesh Spec 304/S15
1281F
1279F
1584F
1585F 1585AF
2076F
2077F
LW denotes long way of mesh dimension. SW denotes short way of mesh dimension. All standard sheet sizes are nominal (normally oversize).
13
FLATTENED MESH
Expanded Steel Mesh
Ref. Mesh Size Size of Open Weight Sheet Size
Expanded Aluminium Mesh
No. Aperture Strand Area Size
mm mm % mm Expanded Stainless
LW SW W T Norm Max Kgs/Sht LWM SWM
Steel Mesh Spec 304/S15
2073F
2074F 2074AF
2490F
3393F
LW denotes long way of mesh dimension. SW denotes short way of mesh dimension. All standard sheet sizes are nominal (normally oversize).
14
FLATTENED MESH
Expanded Steel Mesh
Ref. Mesh Size Size of Open Weight Sheet Size
Expanded Aluminium Mesh
No. Aperture Strand Area Size
mm mm % mm Expanded Stainless
LW SW W T Norm Max Kgs/Sht LWM SWM
Steel Mesh Spec 304/S15
* Galvanised
3394F
3395F
PA R A L L E L S T R A N D
PA R A L L E L S T R A N D
401
402
S Q U A R E
S Q U A R E
Ref Q38 with mesh aperture of 25 x 25mm and Ref Q76 with mesh aperture of 50 x 50mm.
Please enquire for full details. 1601F *
LW denotes long way of mesh dimension. SW denotes short way of mesh dimension. All standard sheet sizes are nominal (normally oversize).
15
SHAPED MESH
Expanded Steel Mesh
Ref. Mesh Size Size of Open Weight Sheet Size
Expanded Aluminium Mesh
No. Centre-Centre Strand Area Size
mm mm % mm Expanded Stainless
LW SW W T Norm Max Kgs/Sht LWM SWM
Steel Mesh Spec 304/S15
* Galvanised
E X P E R F
N6659F *
N6664F *
H E X A G O N S H A P E D M E S H
HEX1
MM I N
I N A R
A R E T
E T
Not
actual
size
MINAR1
LW denotes long way of mesh dimension. SW denotes short way of mesh dimension. All standard sheet sizes are nominal (normally oversize).
16
LARGE MESH Ideal for Window Grilles
R A I S E D N O . 8
F L AT T E N E D N O . 8
17
BRUNDLE
PERFORATED METAL BRUNDLE
MATERIAL - Mild Steel, Galvanised Steel, Stainless Steel 304 & 316, Aluminium & Zinc.
2. Thickness.
4. Thickness.
18
BRUNDLE
PERFORATED METAL BRUNDLE
19
BRUNDLE
PERFORATED METAL BRUNDLE
20
BRUNDLE
PERFORATED METAL BRUNDLE
21
BRUNDLE
PERFORATED METAL BRUNDLE
Examples of Perforations
22
BRUNDLE
PERFORATED METAL BRUNDLE
0300DEC1 11 49 ● -
0300DEC1D 5 52 ● -
0300DEC2 12 46 ● ●
0300DEC4 15 45 ● -
Pattern No. Pattern No. Pattern No. Pattern No.
0300DEC1 0300DEC1D 0300DEC2 0300DEC4
23
BRUNDLE
EDGING SECTIONS BRUNDLE
Suitable for framing flattened Expanded metal up to and including 3.18mm. LF2 Weight kg/m 0.34
7mm
❊ UF6 12.70 0.90 3.30 2540 0.20 1.5mm
25mm
❊ UF7 19.05 1.20 3.30 3810 0.38
Ref. LF2L section for framing ‘angled
❊ UF8 31.75 1.20 3.30 3810 0.62
strand’ type expanded steel having
Suitable for framing raised type expanded steel with strand widths strand widths of 2.40mm or under
of 2.39mm or under. and also flattened expanded steel.
Standard length 2500mm.
❊ UF9 19.05 1.20 5.08 3810 0.38
Steel L sections have been specially
❊ UF10 31.75 1.20 5.08 3810 0.62 produced for framing expanded steel
mesh and they offer several
Suitable for framing raised type expanded steel with strand widths advantages.
of 4.75mm or under.
With two sections only many
expanded steel meshes can be
UF11 19.05 1.50 10.16 3810 0.45 framed easily and with cost saving.
There is less metal in the L sections
than in U sections so they are more
economical and are lighter.
UF12 25.40 1.50 10.16 3810 0.63 With the L sections the fabrication of
framed panels is easier and therefore
less costly. The complete frame is
welded together with mitred corners
and the mesh placed in position and
UF13 25.40 2.95 10.16 3810 1.20
welded at intervals; all welding is
inside the panel.
The need for sliding the mesh into
a gap and clenching is eliminated.
UF14 38.10 1.50 10.16 3810 0.91
The absence of a narrow gap enables
protective finishes such as galvanising,
paint or plastic coating to achieve
total coverage.
UF15 38.10 2.95 10.16 3810 1.79
The L sections can be used with
advantage wherever the framed panel
is to be bolted to a structure with the
Suitable for framing raised type expanded steel with strand widths of 6.09mm or under. rear face of the framing concealed.
Can be used for framing expanded steel walkway grating ref. 2496. For full details see
leaflet IP5.
STAINLESS
STEEL EDGING
UF16 14.29 1.50 12.70 3810 0.46
SECTIONS
Ref No.
Suitable for framing 10g and 12g diameter welded mesh and expanded metal with strand UFS 3
widths up to 3.2mm.
UFS 4
UF18 19.05 1.20 6.50 3810 0.42 UFS 6
UFS 7
UFS 8
UF19 31.75 1.20 6.50 3810 0.66 UFS 9
UFS 10
Dimensions as opposite.
WE CAN SUPPLY, TO ORDER, SOME SIZES IN GALVANISED STEEL OR ALUMINIUM.
24
BRUNDLE
PROFILE EDGING SECTIONS BRUNDLE
TRIANGULAR
1500P005 30 x 22 1.50 1.7 3000 1.15
P005
TRAPEZIUM
1500P006 20 x 20 1.25 1.7 3000 0.67
P006
ROUND
1500P007 10 dia 1.00 1.3 3000 0.243
1500P008 18 dia 1.25 1.7 3000 0.57
1500P009 27 dia 1.50 1.7 3000 1.15
1500P010 27 dia 1.50 2.7 3000 1.15
P010
SQUARE
for welded & woven mesh
1500P013 30 x 30 1.50 3.0 3000 1.48
1500P014 30 x 30 1.50 4.0 3000 1.47
1500P015 30 x 30 1.50 5.0 3000 1.46
P013
P012
25
BRUNDLE
TUBE CLAMPS & TUBE BRUNDLE
C D
B
A
26.9mm 33.7mm 42.4mm 48.3mm
IMPERIAL SIZES
SPLICE LOCK TUBE DIA. TUBE DIA.
Internal Fitting for Joining MM O/D INCHES O/D
Handrail Tube.
60.3mm 42.4mm - Art. 16177C A 26.9 1.1/16"
48.3mm - Art. 16177D
B 33.7 1.11/32"
NOTE: The standard finish is hot-dipped galvanised to BS EN ISO 1461 C 42.4 1.11/16"
Tube Clamps can also be supplied, to order, polyester powder coated, in a range of colours.
D 48.3 1.29/32"
Whilst every care has been taken to ensure that the information given in this manual is correct, F.H.Brundle
reserve the right to alter and revise this information as and when they consider it necessary. E 60.3 2.3/8"
This is in line with their policy of research and development.
26
A size to suit 26.9mm O.D. Tube B size to suit 33.7mm O.D. Tube C size to suit 42.4mm O.D. Tube
D size to suit 48.3mm O.D. Tube E size to suit 60.3mm O.D. Tube
❋ The fittings marked are not designed to withstand lateral loadings ❋❋ These fittings are not to be used as a base plate for guardrails or dependent structures No structure should be built using swivel fittings only
A
B B B
B
C C C
C
D D D
D
E E E
Short Tee 3 Way 900 Elbow Gate Eye Sleeve Joint
Angle Cross Ground Socket Internal Swivel Tee Two Socket Cross
for slope up to 450 allows slope up to 110
27
A size to suit 26.9mm O.D. Tube B size to suit 33.7mm O.D. Tube C size to suit 42.4mm O.D. Tube
D size to suit 48.3mm O.D. Tube E size to suit 60.3mm O.D. Tube
❋ The fittings marked are not designed to withstand lateral loadings ❋❋ These fittings are not to be used as a base plate for guardrails or dependent structures No structure should be built using swivel fittings only
A
B B
B
C C D
C
D D
D
Also new sizes: E E
Clamp on Crossover 900 Corner Swivel Single Male Section 271/20 Ridge Fitting
Male Section of Swivel
28
HANDRAIL SLOPE FITTINGS
152 153
D D
Base Flange 152D Base Flange Short Tee 153D Short Tee
Allows slope up to 110. Upright Pivots up to 110 Allows slope up to 110. Joins middle rail to end
from vertical. uprights on slopes up to 110.
154 155
D D
N.B The tolerence on standard Tube Clamp fittings is between 3 and 5 degrees
29
APPLICATION GUIDE
Wall and Base Flange Enables Tubes Start and End 900 Corner Adjustable Horizontals Wall face Fixing Supplied for Slope
with through top to be joined Section 900 - 1800 up to 450 - state
angle required
Adjustable 124 - 150 - 600 129 - Adjustable 300 - 600 Start End Slope 300 - 600 The 147 neck fits into
150 - 600 from Horizontal 130 - Adjustable 300 - 450 300 - 600 to level rail other fittings and
allows any angle of rail
From Slope to Level Allows fixing to Ground Socket for Riveted Swivel Swivel Base Covers Base 132
Rail using 147 Existing Rail Removable Tubes and then Sealant allows
it to be waterproof
Art. 1603001D
Art. 1603003D
30
BRUNDLE
DDA COMPLIANT BRUNDLE
HANDRAIL FITTINGS
For uprights use Type D tube (48.3mm O.D.) For horizontal use Type C tube (42.4mm O.D.)
DDA01 Upright Connector DDA02 Handrail Curve DDA03 Wall Bracket DDA04 Intermediate Bracket
03 05 07
DDA05 End Return DDA06 900 Bend DDA07 Internal Connector DDA09 Adjustable Bend
06
08 04 01
01 02 07
WARMAGRIP HANDRAIL
Warmagrip™
● 45mm diameter tube.
Our new and innovative
DDA compliant Handrail. ● Available from stock. NEW
EXCLUSIVE ● Load tested to 0.75 Kn.
to F.H.Brundle.
31
BRUNDLE
WARMAGRIP HANDRAIL BRUNDLE
NEW
A B C D E
63.4 Degree Tee Adjustable Tee Midrail Single Adjustable Connector Base Foot Flange
Code Colour Code Colour Code Colour Code Colour Code Colour
52A001G Grey 52A019G Grey 52A021G Grey 52A024G Grey 52A018G Grey
52A001Y Yellow 52A019Y Yellow 52A021Y Yellow 52A024Y Yellow 52A018Y Yellow
F G H I J
90 Degree Elbow 90 Degree Tee Side Mount Bracket 63.4 Degree Midrail Adjustable Midrail
Code Colour Code Colour Code Colour Code Colour Code Colour
52A002G Grey 52A022G Grey 52A015G Grey 52A023G Grey 52A009G Grey
52A002Y Yellow 52A022Y Yellow 52A015Y Yellow 52A023Y Yellow 52A009Y Yellow
Midrail Double Handrail End 3 Way Elbow Midrail Corner Security Fixing Tool
32
BRUNDLE
TUBULAR BRUNDLE
HANDRAIL STANDARDS
SELF COLOUR OR GALVANISED TO FIT 33.7mm o.d 42.4mm o.d & 48.3mm o.d
550
550
550
1010
1067
1100
550
550
550
B B B
65 90
10mm FLAT DRILLED 12mm FLAT DRILLED 10mm FLAT DRILLED
65
LENGTHS OF GALVANISED TUBE STOCKED INTERNAL FITTING FOR JOINING HANDRAIL TUBE
Type Size mm 1.075m 1.45m 3.0m 6.5m
A 26.9 160225
B 33.7 1602341075 16023430 160234
C 42.4 1602421075 16024230 160242
D 48.3 1602481075 1602481450 16024830 160248
42.4mm - 16177C 48.3mm - 16177D
E 60.3 160260
Splice Lock
SPECIAL LENGTHS CUT TO ORDER
33
BRUNDLE
ROOF EDGE PROTECTION BRUNDLE
34
ROOF EDGE PROTECTION
(NO FIXINGS REQUIRED)
Closed Installations
1 Refer to the project drawing.
2 Lay the first Post at the start position.
3 Attach a Counterweight to the first Post.
4 Position the second Post.
5 Position the third Post and attach a
Counterweight.
6 Drop handrail and knee rail into cradle fittings.
7 Repeat the procedure until completion.
8 Check that the maximum spacing for posts is
FULL TECHNICAL DETAILS
no greater than 2000mm.
CAN BE FOUND AT
9 Check that the maximum spacing for OUR WEBSITE
Counterweights is no greater than 4000mm. www.fhbrundle.co.uk
35
BRUNDLE
MORE USEFUL PRODUCTS BRUNDLE
Railing Flange with Toeboard Adaptor Flat Base Horizontal Side Palm
HANDRAIL BENDS
33.7mm o.d 42.4mm o.d 33.7mm o.d 42.4mm o.d
Self Colour Self Colour Galvanised Galvanised
RETURN BENDS
300mm legs 25B25113 25B32113 25B25213 25B32213
400mm legs 25B25114 25B32114 25B25214 25B32214
STAIR
RETURN BENDS Return bend Ramp bend
400mm legs 25B25124 25B32124 25B25224 25B32224
500mm legs 25B25125 25B32125 25B25225 25B32225
RAMP BENDS
500mm legs 25B25135 25B32135 25B25235 25B32235
90 deg BENDS
300mm legs 25B25143 25B32143 25B25243 25B32243
Code: Description Size (W x D x H) mm Hole Size mm TYPE REF. FOR TUBE DIMENSIONS HOLE CENTRES ART.
05LUG4 Slotted Lug 40 x 10 x 60 27 x 14 mm o.d mm mm
05LUG5 Slotted Lug 30 x 10 x 60 27 x 14 2B/4D/5B/8D 33.7 150 x 65 x 10 25-100-25 25F2501
05LUG6 Slotted Lug 30 x 8 x 60 27 x 14 42.4 160 x 65 x 12 25-100-25 25F3201
48.3 170 x 80 x 15 25-120-25 25F4001
Thickness 8mm
GALVANISED ANGLE CLEATS Art. 051515122
Art. Size (W x D x H) mm Hole Size mm
0702028 30 x 30 x 32 15 x 12
09FA552 38 x 38 x 5 19 x 11
09FA553 50 x 50 x 6 19 x 11
09FA554 75 x 50 x 6 19 x 11 Thickness 6mm
Art. 051515128 Thickness 8mm
Art. 051515127
Art. 3603C1
Size - W.52 x D.45 x H.45mm
Hole Size - 25 x 14mm
MILD STEEL DISCS
DIAMETER 1.5mm 3.0mm 5.0mm 6.0mm
CODE NUMBER INDICATES STOCK SIZE
1 /2"
1
201515 20153 20155 20156
2 /2"
1
202515 20253 20255 20256
3 /2"
1
203515 20353 20355 20356
Art. Description Size (W x D x H) mm Hole Size mm WE CAN SUPPLY OTHER
4" 20415 2043 2045 2046 SIZES TO ORDER IN
05LUG10 Self Colour 40 x 140 x 6 Ø 11 27 x 14
05LUG10G Galvanised 40 x 140 x 6 Ø 11 27 x 14 5" 20515 2053 x 2056 MILD STEEL OR
6" 20615 2063 x 2066
STAINLESS STEEL.
37
BRUNDLE
STAINLESS STEEL 304 & 316 PRO
HANDRAIL COMPONENTS
HANDRAIL BRACKETS - FIXED AND ADJUSTABLE
FIX TUBE/TUBE FIX TUBE/FLAT
101 101 101 101
FROM
FIX FLAT/WALL/FLAT STOCK
101 101 101 101
ASK FOR A
FULL CATALOGUE
FIX FLAT/WALL/TUBE
101 101 101 101
310CF 310DF 311CF 311DF 312CF 312DF 310CC 310DD 311CC 311DD 312CC 312DD 313CC 313DD
201C 201D 202C 202D 203C 203D 204C 204D 205C 205D 206C 206D
FROM
FLANGES AND BASE PLATES
STOCK
207C 207D 208C 208D 209C 209D 210C 210D 211C 211D
212C 212D 213C 213D 214C 214D 215C 215D 216C 216D
GLASS CLAMPS
WE HAVE GLASS CLAMPS TO SUIT 8, 10 & 12mm GLASS
FLAT BACK ROUND BACK
6 METRE TUBE
ASK FOR A
FULL CATALOGUE
FROM
STOCK ACCESSORIES
'D' rubbers for Square rubbers for Inline fitting rubbers for Metal security pins Plastic security pins
8, 10 & 12mm glass 8, 10 & 12mm glass 8, 10 & 12mm glass for glass for glass
Metal location plate Plastic screw Allen bolts Allen screws Allen keys
for glass cover caps
High strength retainer. Stud lock Activator (Anaerobic) Stainless Steel Cleaner.
50ml bottle 200ml tin 400ml tin
41
BRUNDLE
STAINLESS STEEL 304 & 316 PRO
HANDRAIL COMPONENTS
101 101 101 101
Rubber Channel
414C 414D 415C 415D 705C 705D To suit 42.4mm & 48.3mm Tube
Glass Thickness 13, 18 & 22 mm
FROM
STOCK
42
BRUNDLE
OPEN STEEL FLOORING BRUNDLE
20mm x 5mm
25mm x 5mm
30mm x 5mm
35mm x 5mm
40mm x 5mm
50mm x 5mm
55mm x 5mm
60mm x 5mm
ALSO AVAILABLE
WITH SERRATED
EDGE BEARER BARS
MANUFACTURED FROM MILD STEEL TO BS EN 100025 S275 JR FOR EXTRA GRIP
Industrial gratings combine great strength with a light structure giving good non-slip properties.
Ideal for use on platforms, galleries, gangways, storage floors etc.
The stock items only have an edge bar on two sides parallel to the first dimension shown in the table.
LIGHT DUTY - Access limited to 1 person GENERAL DUTY - Regular pedestrian traffic HEAVY DUTY - High density traffic
LIGHT DUTY - Access limited to 1 person GENERAL DUTY - Regular pedestrian traffic HEAVY DUTY - High density traffic
44
BRUNDLE
ANTI-SLIP FLOORING PLANKS BRUNDLE
GALVANISED
IN LENGTHS OF APPROX 4 METRES x 50mm DEEP x 2mm THICK
W L
RHINOMIXTE
Holes Ø 5mm burst embossed upwards.
Holes Ø 16mm embossed downwards.
Non slip surface.
Draining surface % Open area: 21.0
Joining clips available.
Width Art.
180mm 34240335
240mm 34240336
300mm 34240337
W L
RHINOPLUS
Split and embossed surface with serrated finish.
Very strong and non slip.
Recommended for high risk slippery areas.
Draining surface % Open area: 47.0
Joining clips available.
Width Art.
180mm 34240340
240mm 34240341
300mm 34240342
45
BRUNDLE
FLOORING PRODUCTS BRUNDLE
Art. 33271243825
Moulded Grating 25mm deep.
Mesh size - 38 x 38mm.
Standard panel - 1220 x 3660mm.
Colour - Green. Also available in Grey & Yellow.
Integral quartz grit top.
Art. 330002 - STAINLESS STEEL FIXING CLIPS
COMPETITIVELY PRICED WITH NON-FERROUS ALTERNATIVES.
46
BRUNDLE
FLOORING PRODUCTS BRUNDLE
TACTILE FLOORING
Tactile Flooring is a 4mm thick GRP tile incorporating raised profiles to warn people
when they are approaching a change in elevation such as railway platforms, pedestrian
crossings, staircase assents and decent areas as well as many other applications.
Tiles are glued and screwed to the existing substrate therefore eliminating the need of
costly excavation.
Tactile Flooring is available in three surfaces and are available in
400mm x 400mm standard tiles.
TYPES AVAILABLE APPLICATIONS
ON STREET BLISTER OFF STREET BLISTER CORDUROY ON STREET BLISTER OFF STREET BLISTER
Art. 33018 Art. 33019 Art. 33020
FIXING KIT
CORDUROY
Blister On-Street Tactile Blister Off-Street Tactile Corduroy Tactile Art. 33021
DURALINE
Duraline is a revolutionary new line marking product aimed at providing a
permanent solution to a company's line marking requirements. The construction
method which combines resin and fibres, means that it is an exceptionally hard
wearing product designed for long life.
Duraline comes in standard lengths of 3000mm.
It has pre-drilled holes at approximately 500mm centres.
Duraline is 50mm wide and 3mm thick.
The chamfered sides are incorporated to reduce the
Art. 33031
possibility of causing a tripping hazard.
47
BRUNDLE
FLOORING PRODUCTS BRUNDLE
55mm 70mm
mm
Up to 3000
30mm
55mm
"Easily cut to the 3mm
Stock Size mm Nosing Art.
required size" 3mm FIXING KIT
3000 70 x 30 33001 I or E
1500 70 x 30 33002 I or E
1000 70 x 30 33003 I or E Two types of grit surface are available.
750 70 x 30 33004 I or E
3000 55 x 55 33005 I or E Type I with its smaller grit size is usually used
1500 55 x 55 33006 I or E for internal use, whilst the Type E with a much
1000 55 x 55 33007 I or E heavier grit profile is ideal for the rigours of the
750 55 x 55 33008 I or E external environment. Art. 33009
● Durable.
● Slip Resistant.
● Corrosion Resistant.
● Simple to Install.
● Complies to DDA & Building Regs. TREAD COVERS FIXING KIT
Stock Size mm Type Art.
3000 x 250 x 4 55mm turn down 33010
1500 x 250 x 4 55mm turn down 33011
1000 x 250 x 4 55mm turn down 33012
750 x 250 x 4 55mm turn down 33013 Art. 33017
Specials made to order up to 345mm Deep 40 or 55mm nosing
LANDING COVERS
Stock Size mm Type Art.
2440 x 1200 x 4 55mm turn down 33014
1200 x 1200 x 4 55mm turn down 33015
800 x 1200 x 4 55mm turn down 33016
BEFORE AFTER
48
BRUNDLE
STAIRTREADS BRUNDLE
OPEN STEEL
Galvanised or Self Colour 41/100mm
Size mm Bar Dimension Self Colour Galvanised
1000 x 283 25 x 5mm 441110283 441210283
1000 x 242 25 x 5mm 441110242 441210242
800 x 283 25 x 5mm 441108283 441208283
800 x 242 25 x 5mm 441108242 441208242
900 x 283 25 x 5mm - 441209283
SPECIALS MADE TO ORDER
16mm
15mm
Cut to Length required and 30mm 115mm 138mm
49
BRUNDLE
STAIRTREADS BRUNDLE
STAIR TREADS GRATING STEP With grating pattern to Edge bars Size Art.
Material: Galvanised Steel match our standard grating
50 x 3 250 x 700 427257G
sizes and with superb
Mesh: 20 x 30mm 50 x 3 250 x 800 427258G
non-slip properties.
50 x 3 250 x 900 427259G
50 x 3 250 x 1000 427251G
60 x 3 300 x 1200 427302G
G = 13mm
15
17
D H c d
A flat step with 9mm punched raised holes to ensure non-slip 150 45/- 35 78
properties, and a 5mm countersunk hole to drain off water and oil. 200 45/57 45 102
225 45/57 45 127
The stair treads have a specially designed front edge to provide excellent
250 45/57 50 142
strength. On 300mm width an additional hole Ø13mm, c/c 48mm from G,
275 45/57 62 143
to provide an extra fixing point.
300 45/57 50 192
These treads are designed according to British Standard BS4592 Part 3 1987.
Typical cross
section of
corrugated BEAMS
beam and post
connection STRAIGHT 3.2m NOMINAL LENGTH (overall 3.5m) Art. 120132
310
Post centres normally 3.2m and 1.6m (1.9m) for extra strength
SCROLL END
Art. 120306
fishtail adds
540mm from
end post
D internal C external B A
0
CORNER INTERNAL 900 CORNER EXTERNAL 90 BULLNOSE END TYPE "B" FISHTAIL END TYPE "A"
Art. 120304 Art. 120303 Art. 120302 Art. 120301
51