Professional Documents
Culture Documents
Board
V1.2
2014-6-29
ELECREALM
http://www.elecrealm.com/
http://stores.ebay.com/elecrealm/
Content
................................................................................................ 15
Chapter 8--Troubleshooting..................................................... 30
1 / 31
http://stores.ebay.com/elecrealm/
Please check the inserting condition of each foot. If some foot is not fully inserted (as
shown in the figure below), please use tweezers to press the exposure to the top of
the foot, let all feet be inserted into well.
2 / 31
http://stores.ebay.com/elecrealm/
3 / 31
http://stores.ebay.com/elecrealm/
4 / 31
http://stores.ebay.com/elecrealm/
Then don't turn over, insert the thin, hard plastic pitch from the FPC cable's bottom.
The thin, hard plastic pitch is shown in the picture. In the actual operation, FPC cable
is at the upper of the plastic pitch and this can't photograph.
5 / 31
http://stores.ebay.com/elecrealm/
Push into the small clip on the both side. When you feel the connection has been the
more tight, stop push. The clip does not necessarily have to be completely pushed
into, so as to avoid damage to the clamp.
6 / 31
http://stores.ebay.com/elecrealm/
7 / 31
http://stores.ebay.com/elecrealm/
When the board is supplied with the adapter only having the DC +12.0V output, the LVDS
cable +5.0V wire cannot be connected to the board’s any pin because the DC+12.0V will be
supplied directly to the LCD and the LCD will be damaged immediately.
It’s prohibited to connect the red wire to the board CN1(power connector) , CN7(AV1+AV2
connector), CN9(VGA connector).
8 / 31
http://stores.ebay.com/elecrealm/
9 / 31
http://stores.ebay.com/elecrealm/
10 / 31
http://stores.ebay.com/elecrealm/
11 / 31
http://stores.ebay.com/elecrealm/
12 / 31
http://stores.ebay.com/elecrealm/
13 / 31
http://stores.ebay.com/elecrealm/
14 / 31
http://stores.ebay.com/elecrealm/
15 / 31
http://stores.ebay.com/elecrealm/
The steps:
Please confirm your PC has been installed the Parallel port driver program. If it
isn’t installed, please install it first.
Step 1. Installed the Parallel port driver program on the PC.
16 / 31
http://stores.ebay.com/elecrealm/
17 / 31
http://stores.ebay.com/elecrealm/
18 / 31
http://stores.ebay.com/elecrealm/
19 / 31
http://stores.ebay.com/elecrealm/
20 / 31
http://stores.ebay.com/elecrealm/
Step 4. Click .
21 / 31
http://stores.ebay.com/elecrealm/
22 / 31
http://stores.ebay.com/elecrealm/
Step 5. Click
23 / 31
http://stores.ebay.com/elecrealm/
Step 6. If the software shows the following image, please click
24 / 31
http://stores.ebay.com/elecrealm/
25 / 31
http://stores.ebay.com/elecrealm/
26 / 31
http://stores.ebay.com/elecrealm/
27 / 31
http://stores.ebay.com/elecrealm/
28 / 31
http://stores.ebay.com/elecrealm/
29 / 31
http://stores.ebay.com/elecrealm/
Chapter 8--Troubleshooting
Question 1 – The power adapter requirement of the board.
The board voltage and the LCD voltage are 2 different parameters.
The board can be worked from +5V to +12V with 3.0A current.
Center: +(Anode)
Around: - (Cathode)
30 / 31