Professional Documents
Culture Documents
LA-110
Advanced Integrated Access Device
networks, with DSL Corrects network errors such as jitter buffer on the fly and compensates for
lost packets
interfaces
LA-110 is an advanced Integrated Access MULTISERVICE OVER ATM
Device (IAD) offering voice, data, and LAN The UNI network interface supports the
service extension over ATM or following ATM adaptation layers:
packet-switched networks.
AAL1 –Transparent transport of serial
The services supported by LA-110 include: data streams, and circuit emulation
High-quality leased lines over E1 or services (CES)
serial data links AAL2 –ATM Forum Loop Emulation
E1 (CES, PRI, UNI) Services (LES) for PSTN and ISDN BRI
and PRI access
Cellular backhaul
AAL5 –Packet traffic (Frame Relay,
High-speed data (transparent and
Ethernet, IP).
Frame Relay)
Ethernet with MAC bridge and IP router
Voice, such as ISDN BRI, PRI or FXS.
When configured to operate as an IP The data payload is processed in The transport of analog voice requires LES
router, LA-110 supports: accordance with the user-selectable over AAL2, which allows several voice
1–2 IP networks (sharing the same application mode: AAL1 or Frame Relay. connections to share the same VC. The
physical Ethernet interface) In AAL1 mode, the data stream is ELCP can also be used.
1–8 WAN ports, each using its own transferred transparently in the CBR
service category. The AAL1 stream mode ISDN INTERFACE
PVC
supports any Layer-2 protocol. Four independent ISDN BRI S0 interfaces
An optional host interface for router comply with ETSI 300012 and ITU-T
management. When the LA-110 data port operates in
Frame Relay mode, the traffic is carried Rec. I.430. The interface characteristics
The router uses static routing entries or over AAL5, in the user-configurable ATM are compatible with many types of ISDN
RIP I/II for routing decisions. It can also service category. switches, including NTT, 5ESS, DMS-100,
use policy-based routing (PBR) to define and NI1.
user-specific routing rules, overriding the The device supports up to 8 DLCIs.
The ISDN interface operates in NT
routing table settings. The Frame Relay interworking mode can (Network Termination) mode, enabling
In IP router mode, LA-110 performs be configured to: direct connection of ISDN terminal
encapsulation per RFC2684, or transfers Service interworking per FRF.8 equipment to “S” ports.
the traffic using PPPoA (with PAP and Network interworking per FRF.5. The ISDN ports require use of LES over
CHAP authentication). AAL2, allowing several connections to
The device serves as a DNS relay, FXS INTERFACE share the same VC. The ELCP can also be
exchanging DNS requests and replies LA-110 can be ordered with four used. The signaling information carried by
between its hosts and the DNS server. independent FXS analog voice interfaces, the multiplexed 64-kbps D channel is
A firewall can be set on each router for direct connection to subscriber POTS transported transparently to the voice
interface (WAN, LAN) for filtering inbound phone, fax, or voiceband modem gateway.
or outbound traffic. equipment. Each port provides power feed
and ringing to the subscriber equipment. E1 AND T1 USER INTERFACE
LA-110 can be configured as a DHCP
server or to DHCP relay mode. The input and output audio levels of each LA-110 can be ordered with one user E1
channel are user selectable. The signals or T1 port with balanced or unbalanced
When operating opposite a RADIUS server, (E1) interfaces.
are encoded by a PCM codec, using
the unit performs client authentication.
64-kbps PCM encoding per ITU-T The E1 interface supports the following
The IP router provides up to 20 NAT/NAPT Rec. G.711, enabling transparent transfer framing modes:
translations. Each translation can be of DTMF signaling, Group III fax signals,
applied to a WAN or LAN port. G732S
and voiceband modem signals.
G732N
Each channel includes a near-end echo
DATA INTERFACE
canceller. The echo canceller can be disabled Unframed
The LA-110 data port is a synchronous when processing fax or modem signals. ISDN PRI (AAL2 only)
serial DCE port, supporting V.35 and X.21
interfaces. The data port operates at rates For compatibility with national E1 ATM UNI.
n 64 kbps in the range of 64 to implementations, the PSTN signaling
2048 kbps. characteristics are user selectable.
In AAL1 mode, LA-110 uses the following Internal –Clock is generated by the DIAGNOSTICS
transmission methods: internal oscillator. LA-110 collects performance monitoring
Structured CES, transmitting each E1 statistics at the physical and ATM layers
bundle over a separate PVC MANAGEMENT for the network and user interfaces. It
Dynamic bandwidth allocation (DB-CES) The unit can be managed using the also provides statistics for individual
for detecting voice channel activity and following ports and applications: connections (AAL1, AAL5).
allocating uplink bandwidth Local out-of-band management via an Comprehensive diagnostic capabilities
accordingly. ASCII terminal connected to the include:
In AAL2 mode, LES is used for voice RS-232 port Physical loopbacks on the network and
support, with or without ELCP. Application Remote out-of-band management via user interfaces
identifiers determine the signaling the LAN port OAM loopback on a VCC
methods: Remote inband management via the Ping for IP connectivity checks.
CAS ATM uplink. Remote management is
performed using Telnet, Web browser, LA-110 stores alarms detected during
PSTN signaling operation in a buffer holding up to
or RADview, RAD’s SNMP-based
DSS1 for ISDN BRI and PRI management access system. 200 alarms.
ISDN PRI remote access with ELCP. Different stations can manage LA-110
LA-110 transparently transfers the simultaneously, enabling monitoring the
ATM-based E1 UNI services at the rate network status from different locations.
1984 kbps.
The balanced T1 user interface offers the PLUG & PLAY
same transmission and signaling methods LA-110 supports automatic configuration
as the E1 user interface. from a remote location. Once the unit is
installed, it needs only to be powered up.
TIMING MODES It then automatically receives its
The device supports flexible timing modes management IP address, and all the
for hierarchical timing distribution in the configuration procedures can be
network. performed from the remote location.
IP router FXS, for direct connection to a 2-wire G732S with or without CRC-4
telephone, RS-464 loop start
MAC Bridge ISDN PRI
Number of ports: 1 LAN, 1–8 WAN Nominal impedance UNI (multiframe or non-multiframe)
600
VLAN: Aware or unaware mode Line Impedance
Return Loss (ERL) 120, balanced
IP Router Better than 20 db
Routing: static, RIP I, RIP II, or both RIP I 75, unbalanced
and RIP II, policy based Encoding
64-kbps PCM per ITU-T Rec. G.711 and Receive Input Level
Number of ports: 1–2 IP networks (sharing 0 to -43 dB
AT&T PUB-43801, μ-Law or A-Law
the same physical LAN interface), 1–8
32-kbps ADPCM per ITU-T Rec. G.726 (see 0 to -12 dB
WAN, host (optional)
Ordering) Transmit Output Level
DHCP services: DHCP server (up to
10 address pools), DHCP relay Frequency Response (Ref: 1020 Hz) ±3V ±10%, balanced
NAT, PAT services ±0.5 dB: 300 to 3000 Hz ±2.37V ±10%, unbalanced
±1.1 dB: 250 to 3400 Hz
Maximum Frame Size Jitter
1536 bytes Signal/Total Distortion (ITU-T ITU-T Rec. G.823
Rec. G.712, G.713 Method 2)
Connector Connectors
0 to -30 dBm0: Better than 33 dB
RJ-45 RJ-45, balanced
+3 to -45 dBm0: Better than 22 dB
Two BNC, unbalanced (via RJ-45 to BNC
ISDN INTERFACES Idle Channel Noise adapter cable)
Number of interfaces Better than -70 dBm0 ( 20 dBrnc)
4
Type
“S”
Data Sheet
T1 INTERFACE Management
Inband: SNMP, Telnet, Web
Compliance
AT&T TR-62411, ANSI T1.403, ITU-T Rec. Out-of-band: LAN port, serial V.24
G.703, G.704, G.706 (RS-232) port
Framing Indicators
Unframed PWR (green) – Power status
ESF WAN (red/green) – WAN interface
SF synchronization status
LAN (green) – LAN transmit/receive
Line Impedance
activity status
100, balanced
Power
Receive Input Level
AC: 100–240 VAC
0 to -36 dB (normal sensitivity)
DC: -48 VDC (-40/-60 VDC)
0 to -30 dB (low sensitivity)
Note: The DC option is not available for units with
Transmit Output Level ISDN, FXS user, or E1 network interfaces.
±3V ±10%; 0 dB, -7.5 dB,
Power Consumption
-15 dB, -22.5 dB (CSU)
7.5W max
±3V ±10%, 0 to 655 feet, (DSU)
Physical
Jitter Height: 43.7 mm (1.7 in)
ITU-T Rec. G.824 Width: 217 mm (8.5 in)
Connectors Depth: 170 mm (6.7 in)
RJ-45, balanced Weight: 0.5 kg (1.1 lb)
GENERAL Environment
Temperature: 0–50°C (32–122°F)
Timing
Humidity: Up to 90%,
Recovered from xDSL interface (NTR)
non-condensing
Recovered from E1 interface
Adaptive
Internal
Data Sheet
LA-110
Advanced Integrated Access Device
product names Optimux and IPmux, are registered trademarks of RAD Data Communications Ltd. All other trademarks are the property of their respective holders.
144-100-05/09 Specifications are subject to change without prior notice. 1988–2012 RAD Data Communications Ltd. The RAD name, logo, logotype, and the terms EtherAccess, TDMoIP and TDMoIP Driven, and the
SUPPLIED ACCESSORIES
Ordering
AC/DC adapter plug (if DC option is
LA-110/~/$/*/#/@/?
ordered)
Legend
~ Power supply (Default=AC): OPTIONAL ACCESSORIES
DC -48 VDC (-40/-60 VDC)
RM-33-2
$ Network interface:
Hardware kit for mounting one or two
SHDSL 2-wire SHDSL
LA-110 units in a 19-inch rack
SHDSL/4W 4-wire SHDSL
SHDSL/IMA IMA over 4x2-wire SHDSL CBL-RJ45/2BNC/E1
E1 Balanced E1 RJ-45 to BNC adapter cable for unbalanced
* ADPCM compression (Default=None): E1 network or user interface
VC4 ADPCM FXS, 4 TS CBL-DB9F-DB9M-STR
VC8 ADPCM ISDN, 8 TS Control port cable
VC30 ADPCM E1, 30 TS
Note: ADPCM compression is not available for units
with IMA over SHDSL network interfaces.
# Voice interface:
E1 E1
T1 T1
FXS 4-port FXS
ISDN 4-port ISDN
Note: FXS and ISDN interfaces are not available for
units with single SHDSL network interfaces.