Professional Documents
Culture Documents
Type Ffet: Single Cartridge O-Ring Seal
Type Ffet: Single Cartridge O-Ring Seal
TYPE FFET
Single Cartridge O-Ring Seal
A – Seat/Mating Ring D
B – Face/Primary Ring
C – Spring E
D – Sleeve
E – Quench/Drain
F – Flush
G – Safety Bushing
Design Features
■ Heavy duty drive
■ Stationary flexible unit permits high tolerance to solids.
■ Stationary external spring improves tolerance to clogging.
■ Indirect positive sleeve/shaft drive prevents shaft damage.
■ Easy, fast, and reliable installation as a pressure-tested
preset unit.
■ Multifunctional gland plate.
FFET
TYPE FFET
Single Cartridge O-Ring Seal
D27
MIN.
PCD
D95 D94
MIN. MAX.
L56
D26
D4
D1
+0.00mm/0.00"
-0.051mm/0.002"
Dry-Running Limits
Speed (rpm)
NOTES:
1400
Standard face combination for
1200 25mm/1" dry-running is silicon carbide/carbon.
40mm/1-5/8" Maximum dry-running operating
1000 50mm/2" pressure = 10 bar g/147 psig.
200
0
0 2 4 6 8 10 (bar g)
0 30 60 90 120 150 (psig)
Pressure
TYPE FFET
Single Cartridge O-Ring Seal
250
15
200
10 150
0 0
20 40 60 80 100 120 140 160 (mm)
(inches)
1 2 3 4 5 6
Seal Size
Multiplier Factors
Multiplier Example for Determining Pressure Rating Limits:
Selection Considerations
Factor Seal: 127mm/5" Diameter Type FFET
Sealed Fluid Petrol/Gasoline, Kerosene, or Better x 1.00 Product: Aqueous Solution
Lubricity Water and Aqueous Solutions (< 80°C/175°F) x 0.75
Face Materials: Silicon Carbide vs. Tungsten Carbide
Sealed Fluid Up to 80°C/175°F x 1.00 Operating Temperature: 80°C/175°F
Temperature From 80°C to 120°C/175°F to 250°F x 0.90 Operating Speed: 3600 rpm
(for carbon From 120°C to 180°C/250°F to 355°F x 0.80
only) From 180°C to 230°C/355°F to 445°F x 0.65
127mm 3600
Velocity = π* x x = 23.9 m/sec (4712 ft/min)
1000 60 sec
(*π = 3.14)
Therefore, velocity is within limits.
Using the Basic Pressure Rating graph, the maximum pressure would be 20 bar g/290 psig.
From the Multiplier Factors chart, apply the multiplier factors for the specific service requirements to
determine the maximum operating pressure for the application:
20 bar g/290 psig x 0.75 = 15 bar g/217 psig
The maximum operating pressure of this 127mm/5" Type FFET seal is 15 bar g/217 psig.
TYPE FFET
Single Cartridge O-Ring Seal
Materials of Construction
SEAL COMPONENTS MATERIALS
Application Criteria
The FFET cartridge seal can be customized for specific installations after review and evaluation by John Crane Engineering.
The following data is needed to evaluate the proposed service.
John Crane
North and Latin Americas Europe, Middle East, Africa Asia Pacific
Morton Grove, Illinois USA Slough, UK Singapore
Tel: 1-847-967-2400 Tel: 44-1753-224000 Tel: 65-222-9161
Fax: 1-847-967-3915 Fax: 44-1753-224224 Fax: 65-223-5035
1-800-SEALING
For your nearest John Crane facility, please contact one of the locations above.
If the products featured will be used in a potentially dangerous and/or hazardous process, your John Crane representative should be consulted prior to their selection and use. In
the interest of continuous development, John Crane Companies reserve the right to alter designs and specifications without prior notice. It is dangerous to smoke while handling
products made from PTFE. Old and new PTFE products must not be incinerated.