Professional Documents
Culture Documents
Objective:
Audit the main 3G parameters for the different RRM functions Delta
3 RNCs [RNC 12 , RNC20, RNC 2] and check for inconsistencies or proposing
new parameter values to improve the network performance.
:
Consistency check:
Discrepancies were found for Only one site for one Parameter only as
Shonw
Power Control
Step Size for DCH BLER weighs the DCH BLER impact to the Delta
RNC HCPC EnableULQualDetRep 1 100% 1 SIR.
If the uplink SIR target has reached the maximum, and the uplink
SIR Target modification commands received by the outer loop PC
controller from the current active PC Entity during
ULQualDetRepThreshold seconds are all greater than zero, then the
uplink outer loop PC controller sends a quality deterioration report
RNC HCPC DownlinkInnerLoopPCStepSize 1 100% 1 to HC. The quality deterioration message to the HC is periodically
repeated, with ULQualDetREpTreshold defining the period, until
either the quality target is resumed, meaning that the condition
specified above is no longer met, or further actions are taken by
HC.
WCEL PtxPICH -8 100% -8 This is the transmission power of the PICH channel.
Defines the power offset for the TFCI symbols relative to the
WCEL PO1_15 8 100% 8 downlink transmission power of a Secondary CCPCH
Defines the power offset for the TFCI symbols relative to the
WCEL PO1_30 12 100% 12 downlink transmission power of a Secondary CCPCH
Defines the power offset for the TFCI symbols relative to the
WCEL PO1_60 16 100% 16 downlink transmission power of a Secondary CCPCH
The number of Page Indicators that can be paged in one PICH radio
WCEL Pi_amount 2 100% 2 frame
The DRX cycle length used by UTRAN to count paging occasions for
WCEL UTRAN_DRX_length 5 100% 5 discontinuous reception
The power offset between the last transmitted preamble and the
PowerOffsetLastPreamblePRACHmessa
WCEL 2 100% 2 control part of the PRACH message (added to the preamble
ge
power to receive the power of the message control part)
Deployed
% of cells at
Object AbbreviatedName Default Values Comments
Default
Range
Consistency check:
% of Deployed
Abbreviated
Object Default cells at Values Comments
Name
Default Range
Defines the noise level in the BTS digital receiver when there is no
WCEL Prxnoise -1050 0.1% -1019,-1050 load (thermal noise + noise figure) , default value is -1050 , if the
other values aren't based on any measurements done before
PrxNoiseAutotunin The auto tuning algorithm of PrxNoise can be switched on or off. The
WCEL 1 100% 1
g current value means that the algorithm is on
Deploye
% of
d
Object Abbreviated Name Default cells at Comments
Values
Default
Range
468,450,
WCEL Ptxtarget 400 0% This is the target value for total transmitted power ,
420,437
Consistency check:
MaxNumberOf
Defines how many re-attempts the RNC shall perform when hunting
RNC AC ReAttemptsCo 2 100% 2
congested logical or hardware resources
ng
MaxFreezingTi This timer ensures that, once frozen, a BTS is not locked to frozen
RNC AC 30 100% 30
me state because a defrost command is missing or arrives too late
Parameter defines the maximum code channel output power for the
WBTS PtxDPCHMax -30 100% -30
power control dynamic range of BTS
Parameter defines the minimum code channel output power for the
WBTS PTxDPCHmin -28 100% -28
power control dynamic range of BTS
330,360,3
WCEL 330 93% This is the transmission power of the primary common pilot channel.
PtxPrimaryCPIC 50,340
H
WCEL UEtxPowerMaxDP
24 100% 24 Defines the maximum transmission power level a UE can use on DPCH
AC CH
WCEL
PtxDLabsMax 370 1.5% 390,370 The planned maximum downlink transmission power of radio link
AC
WCEL 478,460,4 This parameter defines the maximum transmission power of the cell. The
PtxCellMax 430 11.3%
AC 30,447 following values showed good performance in Alexandria .
% of
Deploy
cells
Objec Abbreviat ed
Default at Comments
t ed Name Values
Defau
Range
lt
• Power, Load
• Admission control
• Handover Control
• Packet Scheduling
• HSDPA Parameters.
• HSUPA Parameters.
Discrepancies were found for the following parameters and the sheet
attached includes the changes required for correction
Some of the parameters are related to Load based HO causes which
aren’t activated so it isn’t important parameters.
• QqualMin
• LHOWinSizeONResRateSC
• LHOWinSizeONInterference
• LHOWinSizeOFFResRateSC
• LHOResRateSC
• LHOPwrOffsetUL
• LHOPwrOffsetDL
• LHONumbUEInterRAT
• LHOHystTimeResRateSC
NSN – Mobinil propriety confidential data
Executive Summary (Cont.)
• LHOHystTimeCapaReqRejRate
• LHOHardBlockingRatio
Handover Control
• LHODelayOFFResRateSC
• LHODelayOFFCapaReqRejRate
• LHOCapaReqRejRateUL
• LHOCapaReqRejRateDL
This parameter is used for TDD and GSM cells, and for FDD cells when
WCEL Qhyst1 0 100% 0
cell selection and re-selection quality measure is set to CPICH RSCP.
Qhyst2 is used for FDD cells when cell selection and re-selection quality
WCEL Qhyst2 1 100% 1
measure is set to CPICH Ec/No.
SLHOUseConvPSRTD This parameter defines whether service or load based handovers are
RNC 0 100% 0
ata performed for the conversational PS RT data service.
SLHOUseConvPSSpee This parameter defines whether service or load based handovers are
RNC 0 100% 0
ch performed for the conversational PS speech service.
SLHOprofileStreamP Preferred RAT or WCDMA layer for the streaming PS RT data service in
RNC 0 100% 0
SRTdata the service and load based handovers.
SLHOprofileInteracti Preferred RAT or WCDMA layer for the interactive PS NRT data service
RNC 0 0% 1
vePSNRTdata in the service and load based handovers.Prefered layer is GSM
This parameter defines the load threshold for the common load
NCHOThrComLoadM
RNC 70 100% 70 measurements of the inter-frequency neighbor cells that are
easDRNCCell
controlled by the DRNC.
This parameter defines CPICH EcNo offset for the load and service
ADJI AdjiEcNoOffsetNCHO 12 100% 12
based handover procedure.
GSMDLTxPwrThrNrtP The parameter determines the downlink DPCH TX power threshold for a
FMCG -2 100% -2
S non-real time PS data connection.
-9,-10,-
17,-13,- The parameter determines the absolute CPICH Ec/No threshold
FMCS HHoEcNoCancel -9 34.68% 12,-7,- which is used by the UE to trigger the reporting event 1E. Need to
15,-11,- be Cleared
16,-8
-102,-112,-
99,-104,-
106,-100,-
The parameter determines the absolute CPICH RSCP threshold which is used
FMCS HHoRscpCancel -102 37.1% 97,-109,-
by the UE to trigger the reporting event 1E. Need to Be Cleared
107,-95,-
92,-110,-
105
The parameter determines the time period during which the CPICH RSCP of
FMCS HHoRscpCancelTime 13 95.97% 13,12 the active set cell must stay better than the threshold HHoRscpCancel before
the UE can trigger the reporting event 1E. Need to Be Cleared
-105,-115,-
102,-107,-
The parameter determines the absolute CPICH RSCP threshold which is used
FMCS HHoRscpThreshold -105 37.1% 109,-103,-
by the UE to trigger the reporting event 1F. Need to Be Cleared
100,-112,-
110,-95
10,25,60, This parameter determines the minimum required GSM RSSI level
15,63,13, which the averaged RSSI value of the GSM neighbour cell must
HOPG AdjgRxLevMinHO 15 25%
7,20,0,35, exceed before the coverage (or quality) reason handover to GSM is
30,5 possible. Optimized
AdjgPenaltyTimeNCH Parameter defines penalty time for GSM neighbour cell which has
HOPG 10 92.5% 10,20
O rejected resource request of handover attempt. Need to Be cleared
-100,-50,- The minimum required GSM RSSI level to make service or load reason
HOPG AdjgMinRxLevNCHO -95 17.5%
95,-47 handover to GSM possible need to Be cleraed