Professional Documents
Culture Documents
Afa Ni PDF
Afa Ni PDF
Three Bond 1207C increases its strength in the course of hardening. The resultant
rubber-like solids resist both heat and cold; maintain stability and original status under a
wide range of temperature: from -50°C to +230°C.
Features
• Highly resistant to heat, cold, weather, and has excellent electric insulation.
• It is solvent-less so little shrinkage occurs.
• Suitable for sealing comparatively large clearances.
Characteristics
Before cure
Units Result Remarks
Appearance Red
Specific Gravity 1.50 25°C
Sag Non - sag 25°C
After cure
Appearance Red
Specific Gravity 40 25°C
Hardness 0.3 JIS
Pulling Strength kg/cm² 1.50
Elongation % 170
Linear Shrinkage % 20
Shear Strength kg/cm² 60 Al plates used
Page 1 of 3
All recommendations and statements are based on our research and we believe them to be reliable. We cannot guarantee the results obtained through
the use of our products. All products are sold and samples are given without warranty, expressed or implied, of fitness for any particular purpose or
otherwise. The user shall make his own tests to determine the suitability of the product for his purpose. No agency or representative or employee of this
company is authorised to change this provision.
THREE BOND SINGAPORE PTE LTD TB 1207C
5, JOO KOON CRESCENT Print Date: October 20, 1998
SINGAPORE 629009
Test Condition
Pressure media: Turbine oil, 120°C
The pressure was increased at the rate of 0.1 kg/cm² per minute, until it reached one
kg/cm². Thereafter, the pressure speed was changed to 1 kg/cm² at every 20 minutes.
Three Bond 1207C hardens when reacting with the moisture in the air. The curing cycle
naturally has a close relation with thickness of the layer formed, temperature and relative
humidity.
In 20 - 30 minutes after application at 25°C and 50% RH, the surface becomes tack-free,
and turns into a rubber-like solid in 15 - 16 hours.
The maximum bond strength is obtained only after three days. Electric insulation
property is obtained in seven days after application.
Curing starts from the surface. Hence, when the layer is thick, the cure cycle becomes
longer accordingly.
Handling Precautions
1. Use at well ventilated area.
2. Keep away from children.
3. Combustible. Do not use near fire.
4. Harmful. Do not touch or breathe vapour of this product.
5. In case of eye contact, rinse with water for about 15 minutes, and then consult a
physician.
6. Wash eyes after removing contact lens.
7. Do not use on medical implants.
Page 2 of 3
All recommendations and statements are based on our research and we believe them to be reliable. We cannot guarantee the results obtained through
the use of our products. All products are sold and samples are given without warranty, expressed or implied, of fitness for any particular purpose or
otherwise. The user shall make his own tests to determine the suitability of the product for his purpose. No agency or representative or employee of this
company is authorised to change this provision.
THREE BOND SINGAPORE PTE LTD TB 1207C
5, JOO KOON CRESCENT Print Date: October 20, 1998
SINGAPORE 629009
Shelf Life
12 months unopened and stored at (10 ∼25 C°).
Packaging
Available in packing of 333ml, 150g and 20kg.
Disclaimer
For Industrial Use Only
(Do not use for household purposes)
• The data contained in this report are obtained from experimental results, based on
out test method. We cannot assume absolute responsibility for accuracy and
safety. Before using this product, use your own judgment to determine whether or
not this product meets the requirements of the application and objectives. This
includes the burden of responsibility and hazardous danger. The extent of the
guarantee provides replacement for products, which are clearly unsatisfactory.
• We assume responsibility for neither injury nor property damages resulting from
the misuse of this product.
• We do not assume responsibility without written notice or contract.
Page 3 of 3
All recommendations and statements are based on our research and we believe them to be reliable. We cannot guarantee the results obtained through
the use of our products. All products are sold and samples are given without warranty, expressed or implied, of fitness for any particular purpose or
otherwise. The user shall make his own tests to determine the suitability of the product for his purpose. No agency or representative or employee of this
company is authorised to change this provision.